AP5057 Chipown

Using SOP8 package

1A Linear Li-Ion Battery Charger

General Description Features

The AP5057 is a complete constant current & constant z Programmable Charge Current Up to 1000mA
voltage linear charger for single cell lithium-ion batteries. z No MOSFET, Sense Resistor or Blocking Diode
Its SOP package and low external component count Required
make the AP5057 ideally suited for portable applications. z Complete Linear Charger in SOP Package for single
Furthermore, the AP5057 is specifically designed to Cell Lithium-Ion Batteries
work within USB power specifications. z Constant-Current/Constant-Voltage Operation with
No external sense resistor is needed, and no blocking Thermal Regulation to Maximize Charge Rate
diode is required due to the internal MOSFET Without Risk of Overheating
architecture. Thermal feedback regulates the charge z Charges Single Cell Li-Ion Batteries Directly from
current to limit the die temperature during high power USB Port
operation or high ambient temperature. The charge z Preset 4.2V Charge Voltage
voltage is fixed at 4.2V, and the charge current can be z Charge Current Monitor Output for Gas Gauging
programmed externally with a single resistor. The z Automatic Recharge
AP5057 automatically terminates the charge cycle when z Charge state pairs of output, no battery and fault
the charge current drops to 1/10th the programmed value status display
after the final float voltage is reached. z C/10 Charge Termination
When the input supply (wall adapter or USB supply) is z 50uA Supply Current in Shutdown
removed, the AP5057 automatically enters a low current z 2.9V Trickle Charge Threshold
state, dropping the battery drain current to less than 2uA. z Soft-Start Limits Inrush Current
The AP5057 can be put into shutdown mode, reducing z Battery temperature monitoring function
the supply current to 50uA. z Available in SOP8-PP Package
Other features include Battery temperature monitor,
under-voltage lockout, automatic recharge and two status Package
pins to indicate charge and charge termination. SOP8-PP

Applications
z Cellular Telephones, PDAs, MP3 /MP4 Players
z Charging Docks and Cradles
z Bluetooth 、GPS Applications

Typical Application Circuit

Figure 1. Basic Application Circuit with AP5057

8/F, ChuangYuan Building No.21-1 Changjiang Road, Wuxi New Destrict Tel: +86(510)8521-7718 http://www.chipown.com.cn V2.0 1/7
AP5057 Chipown
Pin Description

Pin No. Pin Name Pin Function

1 TEMP Battery temperature detection input.
2 PROG Charge Current Program, Charge Current Monitor and Shutdown Pin.
3 GND Ground.
4 VCC Positive Input Supply Voltage.
5 BAT Charge Current Output.
6 STDBY The completion of battery charging instructions side.
7 CHRG Open-Drain Charge Status Output.
8 CE Chip Enable Input.

Functional Block Diagram

Figure 2. Block Diagram

8/F, ChuangYuan Building No.21-1 Changjiang Road, Wuxi New Destrict Tel: +86(510)8521-7718 http://www.chipown.com.cn V2.0 2/7
AP5057 Chipown
Absolute Maximum Ratings

PARAMETER SYMBOL MAXIMUM RATING UNIT

Input Supply Voltage Vcc VSS-0.3～VSS+8
PROG pin Voltage Vprog VSS-0.3～Vcc+0.3
V
BAT pin Voltage Vbat Vss-0.3～8
CHAG pin Voltage Vchrg VSS-0.3～VSS+8
BAT pin Current Ibat 1400 mA
PROG pin Current Iprog 1400 uA
Operating Ambient Temperature Topa -40～+85
Storage Temperature Tstr -65～+125 °C
Lead Temperature (Soldering, 10s) 260
Caution: The absolute maximum ratings are rated values exceeding which the product could suffer physical
damage. These values must therefore not be exceeded under any conditions.

Electrical Characteristics

Parameter Symbol CONDITION MIN TYP MAX UNIT

Input supply voltage Vcc 4.25 6.5 V
Charge mode, RPROG =10K 350 2000 uA
Standby mode 150 500 uA
Input supply current Icc Shutdown mode(RPROG not
connected,Vcc<Vbat or 50 100 uA
Vcc<Vuv)
Regulated Output Voltage Vfloat 0°C≤TA≤85°C, IBAT = 40mA 4.177 4.263 V
RPROG =2k,Current mode 450 500 550 mA
RPROG =1k,Current mode 900 1000 1100 mA
BAT pin Current Ibat Standby mode,Vbat=4.2V 0 -2.5 -6 uA
Shutdown mode -1 -2.5 uA
Sleep mode,Vcc=0V -0.3 -2.5 uA
Trickle charge current Itrikl Vbat<Vtrikl,Rprog=1k 80 100 120 mA
Trickle charge Threshold
Vtrikl RPROG =10K,Vbat Rising 2.78 2.9 3.0 V
Voltage
Trickle voltage hysteresis
Vtrhys RPROG =10k 118 135 152 mV
voltage
Vcc Undervoltage lockout
Vuv From Vcc low to high 3.65 3.8 3.9 V
Threshold
Vcc undervoltage lockout
Vuvhys 150 200 300 mV
hysteresis
Vcc-Vbat Lockout Threshold Vcc from low to high 50 100 140 mV
Vasd
voltage Vcc from high to low 5 40 50 mV
C/10 Termination Current Iterm RPROG=1k 0.085 0.1 0.115 mA/mA

8/F, ChuangYuan Building No.21-1 Changjiang Road, Wuxi New Destrict Tel: +86(510)8521-7718 http://www.chipown.com.cn V2.0 3/7
AP5057 Chipown
Threshold RPROG=2k 0.085 0.1 0.115 mA/mA
PROG pin Voltage Vprog RPROG =1k, Current mode 0.93 1.0 1.07 V
CHRG pin Output low voltage Vchrg Ichrg=5mA 0.68 0.75 V
STDBY pin Output low
Vstdby Istdby=5mA 0.68 0.75 V
voltage
Recharge Battery threshold
ΔVrecg VFLOAT - VRECHRG 50 100 200 mV
Voltage
CE high voltage Vce-h 1.2 V
CE low voltage Vce-l 0.6 V
TEMP pin voltage of the
Vtemp-h 80 82 %Vcc
high-end flip
TEMP pin voltage of the
Vtemp-l 43 45 %Vcc
low-end flip
Limited temperature patterns
Tlim 145 ℃
in the junction temperature

Typical Performance Characteristics

Ibat Vs Vbat Ibat vs Vin

600 1200

500
1000

400
800
Ibat(mA)

Ibat(mA)

300
600

200
400

100
Vin=5V,Rprog=2K 200
Rprog=1K
0 Rprog=2K
2.7 3 3.3 3.6 3.9 4.2 4.5 0
4 4.5 5 5.5 6
Vbat(V)
Vin(V)

Vprog vs Vin
Vfloat vs Vin

4.240 1.020

4.230 1.015
4.220
1.010
4.210
1.005
Vfloat(V)

Vprog(V)

4.200
1.000
4.190
0.995
4.180
0.990
4.170

4.160 0.985
Rprog=10K Rprog=10K
4.150 0.980
4 4.5 5 5.5 6 4 4.5 5 5.5 6
Vin(V) Vin(V)

8/F, ChuangYuan Building No.21-1 Changjiang Road, Wuxi New Destrict Tel: +86(510)8521-7718 http://www.chipown.com.cn V2.0 4/7
AP5057 Chipown
Ordering Information

Part Number Mark Package

AP5057
AP5057SPER SOP8-PP
XXXX1
1. XXXX= date code

Pin Function

TEMP (Pin 1): Battery temperature detection input. TEMP pin to receive the battery NTC sensor output. If the TEMP
pin voltage is less than the input voltage is greater than 45% or 80% of the input voltage means the battery temperature
is too low or too high, then the charge has been suspended.
If the TEMP direct access GND, battery temperature detection canceled, the other charged and functioning properly.

PROG (Pin 2): Charge Current Program, Charge Current Monitor and Shutdown Pin. The charge current is
programmed by connecting a 1% resistor, RPROG, to ground. When charging in trickle-current mode, this pin servos to
0.1V.When charging in constant-current mode, this pin servos to 1V. In all modes, the voltage on this pin can be used
to measure the charge current using the following formula:
IBAT = (VPROG/RPROG) • 1000.
The PROG pin can also be used to shut down the charger. Disconnecting the program resistor from ground allows a 3uA
current to pull the PROG pin high. When it reaches the 1.21V shutdown threshold voltage, the charger enters shutdown
mode, charging stops and the input supply current drops to 50uA. This pin is also clamped to approximately 2.4V.
Driving this pin to voltages beyond the clamp voltage will draw currents as high as 1.5mA. Reconnecting RPROG to
ground will return the charger to normal operation.

GND (Pin 3): Ground.

VCC (Pin 4): Positive Input Supply Voltage. Provides power to the charger, VCC can range from 4.25V to 6.5V and
should be bypassed with at least a 10uF capacitor. When VCC drops to within 30mV of the BAT pin voltage, the
AP5057 enters shutdown mode, dropping IBAT to less than 2uA.

BAT (Pin 5): Charge Current Output. Provides charge current to the battery and regulates the final float voltage to
4.2V. An internal precision resistor divider from this pin sets the float voltage which is disconnected in shutdown
mode.

STDBY (Pin 6): The completion of battery charging instructions side. When the battery charge is complete, STDBY
pulled low by internal switches, indicating the completion of charging. In addition, STDBY pin will be in a
high-impedance state.

CHRG (Pin 7): Open-Drain Charge Status Output. When the battery is charging, the CHRG pin is pulled low by an
internal N-channel MOSFET. When the charge cycle is completed, CHRG pin will be in a high-impedance state.

CE (Pin 8): Chip enable input. High input level would AP5057 is in normal working condition; low input level so that
AP5057 is prohibited charging status. CE pin can be TTL or CMOS level-level driver.

8/F, ChuangYuan Building No.21-1 Changjiang Road, Wuxi New Destrict Tel: +86(510)8521-7718 http://www.chipown.com.cn V2.0 5/7
AP5057 Chipown
Package Information

8/F, ChuangYuan Building No.21-1 Changjiang Road, Wuxi New Destrict Tel: +86(510)8521-7718 http://www.chipown.com.cn V2.0 6/7
AP5057 Chipown

Important Notice

Chipown Microelectronics Co. Ltd. reserves the right to make changes without further notice to any products or
specifications herein. Chipown Microelectronics Co. Ltd. does not assume any responsibility for use of any its
products for any particular purpose, nor does Chipown Microelectronics Co. Ltd assume any liability arising out of the
application or use of any its products or circuits. Chipown Microelectronics Co. Ltd does not convey any license under
its patent rights or other rights nor the rights of others.

8/F, ChuangYuan Building No.21-1 Changjiang Road, Wuxi New Destrict Tel: +86(510)8521-7718 http://www.chipown.com.cn V2.0 7/7