0% found this document useful (0 votes)

54 views

Fs tcp2022

This document outlines testing and commissioning procedures for fire service installations in government buildings in Hong Kong. It aims to ensure proper functioning and performance of installed systems through a series of tests during construction and after completion. The procedures include preliminary tests and inspections during installation, functional performance tests, and commissioning activities. They verify that fire service systems meet design requirements and statutory standards. Contractors must follow these procedures and address any deficiencies revealed to obtain final acceptance.

Uploaded by

Vincent Lee

Available Formats

Download as PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

54 views

Fs tcp2022

Uploaded by

Vincent Lee

Available Formats

Download as PDF, TXT or read online on Scribd

You are on page 1/ 210

TESTING AND COMMISSIONING PROCEDURE

FOR

FIRE SERVICE INSTALLATION

GOVERNMENT BUILDINGS

THE HONG KONG SPECIAL ADMINISTRATIVE REGION

2022 EDITION

ARCHITECTURAL SERVICES DEPARTMENT

THE GOVERNMENT OF THE HONG KONG SPECIAL ADMINISTRATIVE REGION
PREFACE

This Testing and Commissioning (T&C) Procedure aims to lay down the minimum testing and
commissioning requirements to be carried out on Fire Service Installation in Government Buildings of
the Hong Kong Special Administrative Region (HKSAR). Such requirements are applicable to both new
installations upon completion and existing ones after major alteration.

The present edition was developed from the General Specification for Building Services
Installation in Government Buildings of the Hong Kong Special Administrative Region 2022 Edition
that was established by the Architectural Services Department (ArchSD).

Electronic version of this T&C Procedure is to be viewed on and free for download from the
ArchSD Internet homepage. As part of the Government’s efforts to limit paper consumption, hard copies
will not be put up for sale.

The ArchSD welcomes comments on this T&C Procedure at any time since the updating of this
T&C Procedure is a continuous process to tie in with technological advances.
DISCLAIMER

This T&C Procedure is solely compiled for Fire Service Installation carried out for or on behalf of
the ArchSD in Government premises of the HKSAR.

There are no representations, either expressed or implied, as to the suitability of this T&C
Procedure for purposes other than that stated above. Users who choose to adopt this T&C Procedure for
their works are responsible for making their own assessments and judgement of all information contained
here. The ArchSD does not accept any liability and responsibility for any special, indirect or
consequential loss or damages whatsoever arising out of or in connection with the use of this T&C
Procedure or reliance placed on it.

The materials contained in this document may not be pertinent or fully cover the extent of the
installation in non-government buildings and there is no intimated or implied endorsement of the sales,
supply and installation of the materials and equipment specified in this T&C Procedure within the
territory of the HKSAR.
TABLE OF CONTENTS
Page

1. Introduction 1

2. Objectives of the Testing and Commissioning Works 1

3. Scope of the Testing and Commissioning Works 2

3.1 Tests and Inspections during Construction

3.2 Functional Performance Tests
3.3 Commissioning, Statutory Tests and Inspections
3.4 Documentation and Deliverables

4. Testing and Commissioning Procedures 4

4.1 Water System Tests

4.2 Electrical and Alarm System Tests
4.3 Gaseous Extinguishing System Tests
4.4 Emergency Lighting and Exit Sign Tests
4.5 Emergency Generator Tests
4.6 Hot Smoke Tests
4.7 Tests on Other Fire Service Installations

Annex

Annex I Testing and Commissioning Progress Chart for Fire Service Installation

Annex II Testing and Commissioning Certificate for Fire Service Installation

Table of Contents T&C Procedure for Fire Service Installation

Page 1 of 1 2022 Edition
(TCP-FS-2022)
Testing and Commissioning Procedure for
Fire Service Installation

1. Introduction

The procedures stated in this Testing and Commissioning (T&C) Procedure cover the activities
in preliminary tests and inspections, functional performance tests and the commissioning of
newly completed Installations and existing ones after major alteration. They are so compiled to
facilitate the work of Project Building Services Engineer (PBSE) and Project Building Services
Inspector (PBSI) / Project Electrical and Mechanical Inspector (PEMI), who are appointed as
the Supervising Officer’s Representatives, in the following aspects with respect to testing and
commissioning :

(a) to vet and approve the T&C procedures proposed and submitted by the contractor for
the Fire Service Installation (Contractor);

(b) to witness those T&C procedures as specified; and

(c) to accept the T&C certificates and other supporting data.

The Contractor shall carry out the T&C works as detailed in this T&C Procedure.
Supplementary T&C plans may be proposed by the Contractor as appropriate and agreed by
PBSE, e.g. for special equipment supplied and/or installed by the Contractor.

The administrative requirements for T&C works are in general as specified in the General
Specification for Building Services Installation in Government Buildings of the Hong Kong
Special Administrative Region 2022 Edition and all current corrigenda/amendments thereto
published before the date of first tender invitation for the Contract issued by the ArchSD (the
General Specification).

All words and expressions shall have the meaning as assigned to them under the General
Specification unless otherwise specified herein.

2. Objectives of the Testing and Commissioning Works

The objectives of the T&C works are:

(a) to verify proper functioning of the equipment/system after installation;

(b) to verify that the performance of the installed equipment/systems meet with the
specified design intent and statutory requirements, if any, through a series of tests and
adjustments; and

(c) to capture and record performance data of the whole Installation as the baseline for
future operation and maintenance.

For the avoidance of doubt, depending on the specific demands of individual installation, the
PBSE may require additional or substitute T&C works in regard to any elements in the
Installation other than those indicated in this T&C Procedure.

Page 1 of 9 T&C Procedure for Fire Service Installation

2022 Edition
(TCP-FS-2022)
3. Scope of the Testing and Commissioning Works

3.1 Tests and Inspections during Construction

The purpose of these tests is to ensure that all components and systems are in a satisfactory and
safe condition before start up. Preliminary adjustment and setting of equipment at this stage
shall also be carried out at the same time to pave way for the coming functional performance
tests.

Before carrying out any test, the Contractor shall ensure that the Installations comply with all
relevant statutory requirements and regulations. The T&C works shall also comply with all site
safety regulatory requirements currently in force. In particular, the Contractor shall note the
statutory requirements listed in the General Specification in carrying out the works.

3.2 Functional Performance Tests

The purpose of functional performance tests is to demonstrate that the Installations can meet the
functional and performance requirements as specified in the Contract. Functional performance
tests should proceed from the testing of individual components to the testing of different systems
in the Installations.

The Contractor may have to make temporary modifications as the tests proceed. The specific
tests required and the order of tests will vary depending on the type and size of systems, number
of systems, sequence of construction, interface with other installations, relationship with the
building elements and other specific requirements as indicated in the Contract. The testing of
systems may have to be carried out in stages depending on the progress of work or as proposed
by the Contractor.

Part of the tests may be required to be carried out in suppliers’ premises in accordance with the
provisions as specified in the Contract.

Any performance deficiencies revealed during the functional performance tests must be
evaluated to determine the cause. After completion of the necessary corrective measures, the
Contractor shall repeat the tests.

If any test cannot be completed because of circumstances that are beyond the control of the
Contractor, it shall be properly documented and reported to the PBSE, who shall then liaise with
the relevant parties to resolve the situation. The Contractor shall resume his testing work
immediately upon the attainment of a suitable testing environment.

3.3 Commissioning, Statutory Tests and Inspections

Commissioning is the advancement of the Installations from the stage of static completion to
full working conditions and to meet the performance requirements as specified in the Contract.
This will include setting into operation and regulation of the Installations. Fine-tuning of the
commissioned system shall be done by the Contractor to match system performance to the actual
needs of the building occupier more closely.

Page 2 of 9 T&C Procedure for Fire Service Installation

2022 Edition
(TCP-FS-2022)
The Contractor shall carry out tests for the Installations to meet statutory requirements as
specified in the Contract. After the proper testing and commissioning of the Installations, the
Contractor shall notify the appropriate authority as specified in the Contract, through the PBSE
of the completion of the Installations and its readiness for inspection and testing. The Contractor
shall arrange for the necessary inspections and tests as required by the Authority.

Statutory tests and inspections required shall include, but not limited to, those specified in the
Codes of Practice for Minimum Fire Service Installations and Equipment and Inspection,
Testing and Maintenance of Installations and Equipment, current edition published by Fire
Services Department, the Government of the Hong Kong Special Administrative Region
(hereinafter refer to as FSDCoP).

Before notifying the appropriate statutory authority for inspection, the Contractor shall arrange
a mock up inspection and test with the PBSE/PBSI to demonstrate the readiness of the fire
service installation for statutory inspection. The mock up test shall be a full inspection test same
as the statutory inspection to be conducted for appropriate statutory authority. The Contractor
shall prepare and make ready all documents required for statutory inspection that will be
examined during the mock up inspection and statutory inspection. The Contractor shall follow
all relevant requirements in the Contract.

Further mock-up test(s) shall be required if the installation fails to meet with the satisfaction of
the PBSE/PBSI in the test. The Contractor should not arrange inspection with the statutory
authority till the satisfactory completion of the mock-up inspection and accepted by the
PBSE/PBSI.

3.4 Documentation and Deliverables

The Contractor shall submit his proposed T&C procedures together with the Testing and
Commissioning Progress Chart shown in Annex I to PBSE for approval.

All inspection and T&C results shall be recorded by the Contractor in the appropriate test record
forms. A complete set of these forms can be found in Annex II.

Data recorded in other formats may also be acceptable subject to prior approval of the PBSE.
Upon completion of all the required T&C works, the Contractor shall complete and sign a
testing and commissioning certificate as shown Annex II to the effect that the agreed T&C
works have been duly carried out.

A functional performance test report covering all measured data, data sheets, and a
comprehensive summary describing the operation of the system at the time of the functional
performance tests shall be prepared and submitted to the PBSE. Deviations in performance as
specified in the Contract or the design intent should be recorded, with a description and analysis
included.

Where required in the Contract, the Contractor shall conduct a final evaluation of the
performance of the Installations, the results of which shall be included in the commissioning
report.

Page 3 of 9 T&C Procedure for Fire Service Installation

2022 Edition
(TCP-FS-2022)
4. Testing and Commissioning Procedures

4.1 Water System Tests

Water systems and circuits shall be tested hydraulically to a minimum pressure of 1,000 kPa or
1.5 times the working pressure whichever is higher applied at the highest point of the system
and held for a period of not less than 15 minutes or the required period as stipulated in the
relevant design standards or FSD Circular Letters whichever is the higher, without leaks
appearing. For automatic sprinkler system, the hydraulic test for all installation pipework shall
be in accordance with the LPC Rules for Sprinkler Installations and the modifications in FSD
Circular Letters.

All pipework shall be thoroughly cleaned and flushed before test. The Contractor shall ascertain
that there is adequate drainage nearby to discharge by large hose in order to ensure flooding of
low level areas will not occur. Where necessary, the Contractor shall provide chemical cleaning
to the pipes. After flushing out the pipework, a flow test shall be performed on the hydrant/hose
reel system in accordance with the requirements of the FSDCoP.

A water supply test with the drain and test valves fully opened shall be made on the sprinkler
system in accordance with the requirements of Loss Prevention Council Rules for Automatic
Sprinkler Installations (including all the LPC Technical Bulletins, Notes, Commentary, and
Recommendation) incorporating BS EN 12845, FSD Circular Letters as required in the General
Specification and all the subsequent amendments by the FSD (hereinafter collectively referred
to as LPC Rules for Sprinkler Installation). An alarm test for at least 30 seconds on the water
gong shall also be carried out by opening the test valve to ensure that it shall sound continuously
after water flow in the system is detected. All controls and air supply system for the pre-action
system, recycling pre-action system and dry pipe system shall also be tested.

An actual water discharge test shall be performed on the long throw sprinkler system/ extended
coverage of sprinkler system/drencher/deluge/water spray/water mist system and for other
automatic fixed installations using water to test the actual system performance. The T&C
procedure of the actual water discharge test shall be submitted by the Contractor and approved
by the Supervising Officer prior to the testing and commissioning.

For street hydrant system without pumps, the Contractor shall test the incoming water supply
pressure at a nearby supply point and at such time as agreed with the PBSE/PBSI before the
commencement of the installation works to establish the adequacy of the water supply pressure.
If the supply pressure is inadequate, the Contractor shall propose remedial measures for the
approval of the PBSE. The Contractor shall find and select the most appropriate nearby supply
point for the test.

The Contractor shall provide whatever hoses or drainage channels required to safely remove the
test water discharged while carrying out these tests in order to ensure that no damage to the
building and property will be caused by the test water.

The Contractor shall submit hydraulic test certificates/reports that shall be signed by the
Contractor's Commissioning Engineer in Charge (CEIC) and by the PBSE or the PBSI who has
witnessed the test. The test certificates/reports shall contain the following particulars: -

Page 4 of 9 T&C Procedure for Fire Service Installation

2022 Edition
(TCP-FS-2022)
- Date of test
- Apparatus or section under test
- Makers number (if any)
- Nature, duration and conditions of test
- Result of test
- Name of Registered Fire Service Installation Contractor’s representative (in block letter)
in charge of test; and
- Name of Employer’s representative at witness the test

4.2 Electrical and Alarm System Tests

Electrical wiring systems shall be tested generally as required by the General Specification,
Testing and Commissioning Procedure for Electrical Installation in Government Buildings,
Hong Kong, issued by the Architectural Services Department, the HKSAR (hereinafter referred
to as EE_TC), and this T&C Procedure. Extra low voltage wiring shall be insulation tested to
a D.C. voltage of twice the normal working voltage of the system. Any tests that are liable to
cause damage to the delicate components such as those incorporating electronic circuits shall
be carried out with the components disconnected.

Smoke detectors shall be checked for correct sensitivity settings by means of manufacturer's
test set and for operation by simulated smoke tests. The smoke detectors shall be tested and
checked for correct settings after every cleaning and right after the occupation of the building.

Rate-of-rise heat detectors shall be tested by gentle application of a heat source such as hair
dryer. Fixed temperature heat detectors must not be tested other than using simulated tests.

Each sensing element of the multi-sensor detectors shall be checked for correct sensitivity
settings by means of manufacturer's test set approved by the PBSE and for operation by
simulated tests.

Soak test of at least 1 week shall be carried out for all automatic detectors at the time after the
completion of all works including fitting-out works and the whole area is cleaned up, normally
at the time of occupation by users or immediately after. Such test shall be deemed to be
successful only if during such period no false fire alarm is occurred or necessary action has been
taken to rectify the causes.

Battery capacity shall be tested by discharging through the alarm circuits and being charged via
the incorporated charger unit. The specific gravity of the electrolyte shall be tested with a clean
hydrometer where applicable. Battery voltage shall be checked.

The Contractor shall arrange power failure load tests to prove proper functioning of the fire
service installation and the associated power supply changeover control during power failure
and fire mode.

The input D.C. supply to the alarm supervisory circuitry shall be checked for correct voltage
and stability such as to match the signal and alarm triggering devices.

For fire alarm direct link to the FSD or FSD's approved centre, the Contractor shall, unless
approved by the PBSE, initiate the fire alarm direct link applications to the appropriate agencies
within 3 months after commencement of the Contract so that the fire alarm direct link will be

Page 5 of 9 T&C Procedure for Fire Service Installation

2022 Edition
(TCP-FS-2022)
connected and tested before the fire service inspections. The Contractor shall submit a copy of
the application document to the PBSE/PBSI for record.

The Contractor shall co-ordinate and shall closely monitor the status of completion of fire alarm
direct link and the telephone line before the fire service inspections by the FSD. The Contractor
shall apply for and provide at the Contractor's own cost the required telephone point for
connection of the fire alarm direct link as required. If the Contractor cannot complete the fire
alarm direct link by the date of fire service inspection by the FSD, the Contractor shall be
responsible for providing all necessary manpower and telephone equipment, at the Contractor's
own expenses, solely for the purpose for a 24-hour/day full attendant service to substitute the
fire alarm direct link, to the approval of the FSD and the PBSE, up to the date of the completion
of the fire alarm direct link. The fire alarm direct link shall be tested to the satisfaction of PBSE
and FSD after connection.

4.3 Gaseous Extinguishing System Tests

Gaseous extinguishing system and manifolds shall be tested in accordance with the relevant
requirements of the General Specification, and all requirements of FSD including FSD Circular
Letters and Fire Protection Notices of the Fire Services Department, the HKSAR (hereinafter
collectively referred to as FSD Requirements and Circular Letters). Pipework shall be tested
for 10 minutes to a minimum of 1.5 times the operating pressure of the system and 1,000 kPa
whichever is larger. A 'puff' test(s) to the installed pipework is required.

The Contractor shall allow carrying out on-site full discharge test after completion of the
installation when required by the FSD to confirm the design conditions can be met and to the
satisfaction of the FSD and approval of the PBSE. Room integrity test should be conducted in
accordance with NFPA 2001 and the statutory requirements. The Contractor shall follow
relevant FSD Requirements and Circular Letters on the requirements of discharge tests. The
Contractor shall refill the gas cylinders with the design agents after the tests and reset all the
equipment after the discharge test.

4.4 Emergency Lighting and Exit Sign Tests

Each self-contained luminaire, internally illuminated exit sign and central battery system shall
be energised from its battery by simulation of a failure of the supply to the normal lighting for
a period of the rated duration of the battery. During this period all luminaires and/or signs shall
be examined and tested in accordance with BS 5266-1, BS EN 50172, BS EN 1838, BS EN
60598-1, BS EN 60598-2-22, the requirements of the FSD and the Buildings Department
wherever applicable to ensure that they are functioning correctly and properly to the relevant
requirements. All tests required in the FSDCoP and in this T&C Procedure shall be carried out
and recorded.

For those emergency lighting systems with battery and backed up by emergency generators,
each emergency generator shall be started up and allowed to energise the emergency lighting
system for a continuous period of at least 1 hour. During this period all luminaires and/or signs
shall be examined visually to ensure that they are functioning correctly. The start up time of the
generator and the illumination level in terms of 'lux' and 'cd/m2' etc. shall be recorded and the
Contractor shall ensure that the start up time matches with FSD's requirements.

Page 6 of 9 T&C Procedure for Fire Service Installation

2022 Edition
(TCP-FS-2022)
For emergency lighting system and exit signs provided with central monitoring, testing and
logging system, the system shall be tested in accordance with the manufacturer's specification
and to meet the requirements in the FSDCoP, EE_TC and this T&C Procedure.

Where indicated that there is emergency lighting installation and/or exit signs in a building
carried out by others and not included in the work under the Installations, the Contractor shall
follow the requirements of the General Specification with particular attention to Clause
8.1.11.1.12. The Contractor shall include the emergency lighting installation and exit signs as
part of the fire service installation in the submission to the FSD with the necessary information
to be provided by the relevant parties.

4.5 Emergency Generator Tests

The Contractor shall carry out full visual inspection, safety check, functional and performance
test for the emergency generator installation. The tests shall include measurement on noise
confirming compliance with the statutory requirements and/or conditions as required by the
Environmental Protection Department, the HKSAR.

After full test of the fire service installations in a building or premises has been carried out, with
all systems connected to the mains electricity supply, the mains electricity supply shall be
switched off to simulate power failure and the emergency generator shall start automatically.

When the emergency generator has gained its capacity and is ready to accept the fire service
load, each fire service installation shall be switched on until all installations are in operating
conditions. If an automatic starting programme or device is provided for controlling the starting
sequence of the equipment using emergency power supply, the programme or device shall be
allowed to operate and test. A 'simultaneous running' test shall then take place and shall last for
a continuous period of 1 hour. During this period, the performance of each fire service
installation shall be monitored and recorded.

After 1 hour of testing, the emergency generator set shall be examined and all instruments,
safety devices etc. shall indicate normal running of the generator.

The fuel tank shall be topped up after the tests.

Where the emergency generator installation is provided as work under the installations, in
addition to the tests required by the FSD, the Contractor shall test and commission the
emergency generator installation complying with the requirements in the Contract.

Where indicated that there is emergency generator installation in the same building carried out
by others and not included in the work under the Installations, the Contractor shall follow the
requirements of the General Specification, with particular attention to Clause 8.1.11.3. The
Contractor shall include the emergency generator installation as part of the fire service
installation in the submission to the FSD with the necessary information to be provided by the
relevant parties.

4.6 Hot Smoke Tests

Hot smoke tests shall be carried out where specified or required by the FSD. The Contractor
shall prepare and submit proposals including all calculations, designs, and computer fluid

Page 7 of 9 T&C Procedure for Fire Service Installation

2022 Edition
(TCP-FS-2022)
dynamic simulations, etc., arrange, co-ordinate and carry out the hot smoke tests to meet the
purpose for simulating the prototype of a real fire under specific dynamic buoyant flow of smoke
and heat intensity in a controlled manner and for assessing the performance of smoke
management system, smoke control system and smoke extraction system with the given
building geometry. Hot smoke tests shall follow FSDCoP, Australian Standard AS 4391
"Smoke Management System – Hot Smoke Test" or approved international standards and
practises and to the satisfaction of the FSD and the PBSE. The Contractor shall be responsible
for the submissions to the FSD and obtain comments and approval from the FSD and all relevant
parties on the detailed requirements and arrangement for the hot smoke test at early stage of the
Contract.

The Contractor shall provide all materials, equipment, facilities, fuels, manpower and the like
for hot smoke tests. The Contractor shall co-ordinate and arrange with the Building Contractor
to provide all necessary temporary protections to the building finishes, parts, fixtures, furniture,
services and other building works during the tests. The Contractor shall submit the details of
such requirements to the Building Contractor in good times before the tests and to the PBSE for
approval. The Contractor shall supply and install all necessary protections and allow all
appropriate provisions to other parts of the building not covered by the Building Contractor so
as not to cause any damage, and to keep any disturbance to the possible minimum to any
occupants or services during hot smoke tests. The Contractor shall co-ordinate with the
Building Contractor and the FSD and shall propose a suitable location and a suitable fire size
according to the proposals approved by the FSD for carrying out the hot smoke tests. The
Contractor shall carry out risk assessments of the hot smoke tests and allow adequate protections
and provisions for the risks. The Contractor shall employ a standby fire brigade including fire
engine from the FSD during hot smoke tests for the purpose of fire safety. The Contractor shall
deem to allow all necessary insurance coverage for the hot smoke tests when such or any part
of it is not covered under the general insurance policy of the Building Contractor for the Site.

The Contractor shall arrange and co-ordinate with relevant parties in carrying out the hot smoke
tests. The Contractor shall employ a qualified professional engineer to arrange the details and
co-ordinate the hot smoke tests. The engineer employed shall be a Registered Professional
Engineer in Hong Kong under the Engineers Registration Ordinance (Cap. 409) in fire, building
services or mechanical discipline (or equivalent approved professional qualifications) with
proof of experience of at least 3 years in hot smoke test and Fire Service Installation
works. The professional status and qualifications of the Registered Professional Engineer shall
also be acceptable by FSD and the Supervising Officer.

Hot smoke tests shall be carried out to verify the effectiveness of the smoke management
systems and the like included in the work under the installations before the compliance
inspections of the FSD. Where hot smoke tests indicate deficiency in any systems, the
Contractor shall rectify them to the satisfaction of the FSD and the PBSE at no additional cost.
Where the smoke management systems are not included in the work under the installations, the
Contractor shall report the deficiency to the PBSE and propose improvement measures. The
Contractor shall submit a detailed test report at the end of each test that shall include all the
measurement results and data, recommendations and improvement measures. A final report
shall be prepared and submitted after the compliance inspections for the approval of the FSD.

Details of the hot smoke test requirement shall refer to the General Specification and FSDCoP.

Page 8 of 9 T&C Procedure for Fire Service Installation

2022 Edition
(TCP-FS-2022)
4.7 Tests on Other Fire Service Installations

Tests on fire service installations other than those listed in this T&C Procedure shall be in
accordance with the FSDCoP and FSD Requirements and Circular Letters, and the approved
detailed testing and commissioning procedures proposed by the Contractor and approved by the
PBSE. The Contractor shall propose and submit detailed testing and commissioning procedures
for all fire service installations for approval by the PBSE where such details of testing and
commissioning are not available in EE_TC, FSDCoP and this T&C Procedure. The detailed
testing and commissioning procedures submitted shall be comprehensive and sufficient to
demonstrate the functioning and performance of all the systems and equipment.

Page 9 of 9 T&C Procedure for Fire Service Installation

2022 Edition
(TCP-FS-2022)
Annex I
Testing and Commissioning Progress Chart for
Fire Service Installation
Contract Number :
Contract Title :
Name of Sub-contractor :
Name of Main Contractor :
Contract Period: __/__/20__ to __/__/20__ *Revised /Actual Completion Date: __/__/20__
dd/mm/yyyy dd/mm/yyyy

Testing and Commissioning Progress Chart for Fire Service Installation (Rev. ) (Note 1)
Dates Remark
(Note 2)

Activities Reference S A S A S A S A S A S A S A S A
to T&C
Procedure
Clause
1. Hydrant and Hose Reel 3.1
System
Visual inspection
System Readiness for
Hydraulic Test
Functional and
performance test
Submission of test record

2. Automatic Sprinkler 3.2

System
Visual inspection
System Readiness for
Hydraulic Test
Functional and
performance test
Submission of test record

3. Manual and Automatic 3.3

Fire Alarm System and
Fire Alarm Control
System
Visual inspection
Functional and
performance test
Submission of test record

Annex I T&C Procedure for Fire Service Installation

Page 1 of 3 2022 Edition
(TCP-FS-2022)
Testing and Commissioning Progress Chart for Fire Service Installation (Rev. ) (Note 1)
Dates Remark
(Note 2)

Activities Reference S A S A S A S A S A S A S A S A
to T&C
Procedure
Clause
4. Gaseous Extinguishing 3.4
System
Visual inspection
System Readiness for
Pneumatic Test
System Readiness for
Puff Test
Functional Test
Submission of test record

5. Street Hydrant 3.5

Visual inspection
System Readiness for
Hydraulic Test
Functional and
performance test
Submission of test record

6. Drencher System 3.6

Visual inspection
System Readiness for
Hydraulic Test
Functional and
performance test
Submission of test record

7. Audio/Visual Advisory 3.7

System
Visual inspection
Functional and
performance test
Submission of test record

8. Portable Hand- 3.8

Operated Approved
Appliances
Visual inspection

9. Fire Shutters 3.9

Visual inspection
Functional test
Submission of test record

Annex I T&C Procedure for Fire Service Installation

Page 2 of 3 2022 Edition
(TCP-FS-2022)
Testing and Commissioning Progress Chart for Fire Service Installation (Rev. ) (Note 1)
Dates Remark
(Note 2)

Activities Reference S A S A S A S A S A S A S A S A
to T&C
Procedure
Clause
10. Emergency Generator 3.10
Installation
Visual inspection
Functional test
Submission of test record

11. Emergency Lighting & 3.11

Exit Signs
Visual inspection
Functional test
Submission of test record

12. VAC Control System 3.12

Visual inspection
Functional test
Submission of test record

13. Pressurisation of 3.13

Staircases System
Visual inspection
Functional test
Performance test
Submission of test record

14. Smoke Extraction 3.14

System
Visual inspection
Functional test
Performance test
Submission of test record

15. Hot Smoke Test 3.15

Visual inspection
Functional test
Performance test
Submission of test record

16. Submission of T&C

Certificate

Notes
* Delete as appropriate
(1) Insert revision no.
(2) Insert additional columns as necessary
S - schedule % completion
A - actual % completion

Annex I T&C Procedure for Fire Service Installation

Page 3 of 3 2022 Edition
(TCP-FS-2022)
Annex II
Testing and Commissioning Certificate for
Fire Service Installation

Contract Number :
Contract Title :

Part 1 Details of Project

1.1 Project title :

1.2 P.W.P. No. :
1.3 Contract Number :
1.4 Sub-contractor :
1.5 Main Contractor :
1.6 Name of *PBSE :
1.7 Name of *PBSI :

Part 2 Declaration

2.1 I certify that the Fire Service Installation as specified in the Contract/Sub-
contract/Quotation at the above location has been inspected, tested and
commissioned in accordance with this Testing and Commissioning (T&C) Procedure
and/or any other procedures as agreed between the *PBSE and the Contractor. The
results are satisfactory in the aspects as mentioned in Part 3 and/or as recorded in
Part 4 of this Certificate, except that indicated in the COMMENTS items.

2.2 I also certify that site tests have been performed in accordance with the requirements
set in this T&C Procedure and that the results are satisfactory. A record of the tests
has been prepared and submitted to the *PBSE.

Name of Authorised Contractor’s Representative: Signature:

Designation /Post of Contractor’s Representative: Date Signed:

Name and Stamp of Contractor: Telephone Number:

* delete /amend if required

Annex II T&C Procedure for Fire Service Installation

Page 1 of 194 2022 Edition
(TCP-FS-2022)
Items tested/ Items witnessed
checked by by
Contractor PBSE/PBSI

Part 3 : Items to be Inspected and Tested

3.1 Fire Hydrant and Hose Reel System
Type of Building: *Domestic/Industrial/ Godown/ Others

3.1.1 F.S.I. Drawings Against Building Plans

3.1.1.1 Check nos. and locations of:

a) Fire service inlets Yes/No/N.A. Yes/No/N.A.

b) Fire hydrants and hose reels Yes/No/N.A. Yes/No/N.A.

c) Fixed fire pumps Yes/No/N.A. Yes/No/N.A.

d) Intermediate booster pumps Yes/No/N.A. Yes/No/N.A.

e) Water tank and capacity Yes/No/N.A. Yes/No/N.A.

3.1.2 Plumbing Line Diagram

3.1.2.1 Check:
a) Pipings are suitably connected to the fire pumps, fire hydrants, hose reels *Yes/No/N.A. *Yes/No/N.A.
and fire service inlets.

b) Size of the rising mains are correct. Yes/No/N.A. Yes/No/N.A.

c) Size and height of the inter-connection header pipe(s) for fire service *Yes/No/N.A. *Yes/No/N.A.
inlets is correct.

d) By-pass pipings for intermediate booster pumps. Yes/No/N.A. Yes/No/N.A.

e) F.S. appliance to be provided by FSD to test the system. (to be confirmed *Yes/No/N.A. *Yes/No/N.A.
by FSD)

3.1.3 Visual Inspection

3.1.3.1 Water Supply

a) Is an independent town main connection provided for the FH/HR *Yes/No/N.A. *Yes/No/N.A.
installation alone?

b) Does the size of the incoming water pipe from the town mains up to the *Yes/No/N.A. *Yes/No/N.A.
supply tank tally with the vertical plumbing diagram approved by W.S.D.

c) Are the effective water capacity correct of the :

Tested / Checked by : Signature - Post :

(Name of Authorised Contractor’s Representative) Tel. No. :
( ) Date :
Witnessed by : Signature - Post :
(Name(s) of *PBSE/PBSI) Tel. No. :
( ) Date :

Annex II T&C Procedure for Fire Service Installation

Page 2 of 194 2022 Edition
(TCP-FS-2022)
Items tested/ Items witnessed
checked by by
Contractor PBSE/PBSI

(i) Supply tank? Yes/No/N.A. Yes/No/N.A.

(ii) Transfer tank? *Yes/No/N.A. *Yes/No/N.A.

d) Are the ball valves of the water tank readily accessible? *Yes/No/N.A. *Yes/No/N.A.

e) Does the size of the water pump suction water pipe from the tank match *Yes/No/N.A. *Yes/No/N.A.
the size of the pump suction inlet?

f) Are levels of suction pipes correct? Yes/No/N.A. Yes/No/N.A.

g) Are puddle flanges of the same sizes as the water pump suction pipes? *Yes/No/N.A. *Yes/No/N.A.

h) Are automatic priming arrangements provided for suction lift condition? *Yes/No/N.A. *Yes/No/N.A.

i) Is anti-overheating circulating pipe provided? Yes/No/N.A. Yes/No/N.A.

j) Is vortex inhibitor provided and clear of debris? Yes/No/N.A. Yes/No/N.A.

k) Are water tanks clear of debris? Yes/No/N.A. Yes/No/N.A.

l) Has the Fire Service Completion Advice issued? Yes/No/N.A. Yes/No/N.A.

3.1.3.2 Pipework

a) Are water pipes up to 150 mm dia. to BS EN 10255 / ISO 65/ BS EN *Yes/No/N.A. *Yes/No/N.A.
10217-1 medium grade or other approved type?

b) Are water pipes larger than 150 mm dia. to BS EN 545:2010 Class 64 (dia. *Yes/No/N.A. *Yes/No/N.A.
200 – 350) or Class 50 (dia. 400 – 600) or other approved type?

c) Are U/G water pipes to BS EN 545:2010 Class 100 (dia. 80 -150), Class *Yes/No/N.A. *Yes/No/N.A.
64 (dia. 200 – 350) or Class 50 (dia. 400 – 600) or to BS EN 10255 / ISO
65 heavy grade or other approved type?

d) Are U/G water pipes protected with two coats of bituminous paint and *Yes/No/N.A. *Yes/No/N.A.
wrapped with self-amalgamating tapes and mastics having minimum 55%
overlapping?

e) Are water pipes up to 50 mm dia. operating at working pressure not *Yes/No/N.A. *Yes/No/N.A.
exceeding 1600 kPa provided with screw joints?

f) Are water pipes of dia. larger than 50 mm and up to 150 mm operating on *Yes/No/N.A. *Yes/No/N.A.
or below 1600 kPa provided with mechanical pipe couplings or screwed
joints?

g) Are water pipes of dia. larger than 150 mm provided with flanged joints *Yes/No/N.A. *Yes/No/N.A.
and flanged fittings?

h) Are U/G water pipes provided with mechanical pipe couplings or other *Yes/No/N.A. *Yes/No/N.A.
approved couplings?

Tested / Checked by : Signature - Post :

(Name of Authorised Contractor’s Representative) Tel. No. :
( ) Date :
Witnessed by : Signature - Post :
(Name(s) of *PBSE/PBSI) Tel. No. :
( ) Date :

Annex II T&C Procedure for Fire Service Installation

Page 3 of 194 2022 Edition
(TCP-FS-2022)
Items tested/ Items witnessed
checked by by
Contractor PBSE/PBSI

i) Are water pipes provided with adequate disconnecting flanges, *Yes/No/N.A. *Yes/No/N.A.
mechanical pipe couplings or screwed unions for future ease of
dismantling?

j) Are pipes suitably connected to the fire pumps, hydrants, hose reels and *Yes/No/N.A. *Yes/No/N.A.
fire service inlets?

k) Are bends of water pipes larger than 50 mm dia. and bends of water pipes *Yes/No/N.A. *Yes/No/N.A.
installed outside false ceiling/concealed void of long radius type, or as
approved?

l) Are galvanised mild steel sleeves provided for pipes through wall or slab? *Yes/No/N.A. *Yes/No/N.A.

m) Are spaces between water pipes and pipe sleeves through wall or slab *Yes/No/N.A. *Yes/No/N.A.
filled with approved fire proof material and sealant?

n) Are fire rated pipe sleeves provided for pipes through fire rated wall or *Yes/No/N.A. *Yes/No/N.A.
slab?

o) Are spaces between water pipes and pipe sleeves through fire rated wall *Yes/No/N.A. *Yes/No/N.A.
or slab filled with approved fire proof material and sealant?

p) Are adequate clearances provided between pipe and sleeve? *Yes/No/N.A. *Yes/No/N.A.

q) Are sleeves projected at least 100 mm above finish floor level and at least *Yes/No/N.A. *Yes/No/N.A.
150 mm above roof finish

r) Are pipes installed without being embedded in concrete structure? *Yes/No/N.A. *Yes/No/N.A.

s) Are adequate pipe hangers and supports provided as required? *Yes/No/N.A. *Yes/No/N.A.

t) Are pipe hangers and supports rigidly fixed and unbroken? *Yes/No/N.A. *Yes/No/N.A.

u) Are expansion pipe joints provided at location through building expansion *Yes/No/N.A. *Yes/No/N.A.
joint?

v) Are strainers in water pipes cleaned? Yes/No/N.A. Yes/No/N.A.

w) Are adequate air vents and drain cocks provided? *Yes/No/N.A. *Yes/No/N.A.

x) Are valves closed at clockwise rotation? Yes/No/N.A. Yes/No/N.A.

y) Are valves locked at OPEN position with security devices including *Yes/No/N.A. *Yes/No/N.A.
chains, padlocks, tamper-proof serially numbered security tags, and
durable warning labels to prevent tampering/unauthorised operation, and
with a log book to keep track of maintenance services and operation, of
the valves?

z) Are by-pass pipings provided for intermediate booster pumps? *Yes/No/N.A. *Yes/No/N.A.

aa) Are pressure gauges of correct specification? Yes/No/N.A. Yes/No/N.A.

Tested / Checked by : Signature - Post :

(Name of Authorised Contractor’s Representative) Tel. No. :
( ) Date :
Witnessed by : Signature - Post :
(Name(s) of *PBSE/PBSI) Tel. No. :
( ) Date :

Annex II T&C Procedure for Fire Service Installation

Page 4 of 194 2022 Edition
(TCP-FS-2022)
Items tested/ Items witnessed
checked by by
Contractor PBSE/PBSI

ab) Are isolating cocks/valves provided for pressure gauges? *Yes/No/N.A. *Yes/No/N.A.

ac) Are sprinkler heads provided at top of refuse chutes? *Yes/No/N.A. *Yes/No/N.A.

ad) Do water pipe sizes tally with drawings? Yes/No/N.A. Yes/No/N.A.

ae) Are equipotential earth bondings provided for all sections of the *Yes/No/N.A. *Yes/No/N.A.
pipeworks?

3.1.3.3 Fire Hydrant

a) Do the layouts of the hydrant tally with the latest approved building plans? *Yes/No/N.A. *Yes/No/N.A.

b) Are outlets of male round thread? Yes/No/N.A. Yes/No/N.A.

c) Are outlets of female instantaneous? Yes/No/N.A. Yes/No/N.A.

d) Are outlets adaptable to F.S.D equipment? Yes/No/N.A. Yes/No/N.A.

e) Are the hydrant valves individually controlled by wheel operated screw *Yes/No/N.A. *Yes/No/N.A.
valve designed to open in counter-clockwise direction?

f) Is the direction of opening engraved in both English and Chinese on the *Yes/No/N.A. *Yes/No/N.A.
wheel of the valve?

g) Are the centre of coupling of hydrant outlets between 800mm and *Yes/No/N.A. *Yes/No/N.A.
1200mm above finished floor level?

h) Is the hydrant outlet provided with bronze caps complete with chains? *Yes/No/N.A. *Yes/No/N.A.

i) If the hydrant is located in a recess to which a door is fitted, is such door *Yes/No/N.A. *Yes/No/N.A.
fitted with non-lockable pull open handle and with the words “FIRE
HYDRANT ((消防栓), lettering of which shall be of at least 50mm high?

j) Is adequate clearance provided around the hydrant outlet and valve for the *Yes/No/N.A. *Yes/No/N.A.
free use of the hydrant?

k) Is the outlet not obstructing any door opening, or any existing exit route? *Yes/No/N.A. *Yes/No/N.A.

l) Are the hydrants at positions without being concealed by adjacent opened *Yes/No/N.A. *Yes/No/N.A.
doors?

m) Is water fed by gravity? Yes/No/N.A. Yes/No/N.A.

n) Is water fed by fixed fire pump? Yes/No/N.A. Yes/No/N.A.

3.1.3.4 Hose Reel

Tested / Checked by : Signature - Post :

(Name of Authorised Contractor’s Representative) Tel. No. :
( ) Date :
Witnessed by : Signature - Post :
(Name(s) of *PBSE/PBSI) Tel. No. :
( ) Date :

Annex II T&C Procedure for Fire Service Installation

Page 5 of 194 2022 Edition
(TCP-FS-2022)
Items tested/ Items witnessed
checked by by
Contractor PBSE/PBSI

a) Do the layouts of the hose reels tally with the latest approved building *Yes/No/N.A. *Yes/No/N.A.
plans?

b) Is the length of the tubing not exceeding 30 m? Yes/No/N.A. Yes/No/N.A.

c) Is the internal bore of tubing not less than 19mm in diameter? *Yes/No/N.A. *Yes/No/N.A.

d) Is the hose reel drum not less than 150mm in diameter? *Yes/No/N.A. *Yes/No/N.A.

e) Is nozzle fitted with simple two-way on/off valve and the valve is not *Yes/No/N.A. *Yes/No/N.A.
spring loaded?

f) Are the control valves of gate type or of simple two-way ball type? *Yes/No/N.A. *Yes/No/N.A.

g) Are the gates valves are closed by clockwise rotation? *Yes/No/N.A. *Yes/No/N.A.

h) Are the rising mains and associated pipework not less than 40mm nominal *Yes/No/N.A. *Yes/No/N.A.
bore?

i) Are the pipes feeding individual hose reel are not less than 25mm nominal *Yes/No/N.A. *Yes/No/N.A.
bore.

j) Can every part of the building be reached by a nozzle? Yes/No/N.A. Yes/No/N.A.

k) Is the nozzle capable of projecting a 6-metre jet? Yes/No/N.A. Yes/No/N.A.

l) Are the control valves sited adjacent to the nozzles? *Yes/No/N.A. *Yes/No/N.A.

m) Is the orifice of nozzle not less than 4.5 mm? *Yes/No/N.A. *Yes/No/N.A.

n) Are the control valves and nozzles 1350 mm or less above finished floor *Yes/No/N.A. *Yes/No/N.A.
level, and for a recessed type hose reel not more than 500 mm from the
surface of the wall?

o) Are guide rings provided for fixed type hose reel? *Yes/No/N.A. *Yes/No/N.A.

p) Is suitable guide ring provided to permit easy withdrawal of the hose reel *Yes/No/N.A. *Yes/No/N.A.
tubing?

q) Are the jet nozzles unbroken and housed in glass-fronted cabinet secured *Yes/No/N.A. *Yes/No/N.A.
under lock and key?

r) Is the guide bracket unbroken and installed? Yes/No/N.A. Yes/No/N.A.

s) Are strikers provided inside the cabinets? Yes/No/N.A. Yes/No/N.A.

t) Are manual fire alarm call points sited at a prominent position near the *Yes/No/N.A. *Yes/No/N.A.
hose reels?

u) Are the manual fire alarm call points not more than 1200 mm above the *Yes/No/N.A. *Yes/No/N.A.
finished floor level?

Tested / Checked by : Signature - Post :

(Name of Authorised Contractor’s Representative) Tel. No. :
( ) Date :
Witnessed by : Signature - Post :
(Name(s) of *PBSE/PBSI) Tel. No. :
( ) Date :

Annex II T&C Procedure for Fire Service Installation

Page 6 of 194 2022 Edition
(TCP-FS-2022)
Items tested/ Items witnessed
checked by by
Contractor PBSE/PBSI

v) Upon actuation of any manual fire alarm call point in the building, shall *Yes/No/N.A. *Yes/No/N.A.
the fixed fire pump come into operation regardless of the zoning of the fire
alarm call point?

w) Are operation instruction notices provided for and adjacent to each of the *Yes/No/N.A. *Yes/No/N.A.
hose reels?

x) Is the notice clearly marked with the standard wordings in English and *Yes/No/N.A. *Yes/No/N.A.
Chinese characters of at least 5mm high in red letters on white background
or vice versa?

y) Are hose reels of swinging cradle type? Yes/No/N.A. Yes/No/N.A.

z) Can the cradle be swung freely into the corridor or passage when required? *Yes/No/N.A. *Yes/No/N.A.

aa) Is the tubing of the hose reels properly wound round the drum without *Yes/No/N.A. *Yes/No/N.A.
kinking?

ab) Are the outer faces of the hose reels flush with the wall when the reels are *Yes/No/N.A. *Yes/No/N.A.
not in use?

ac) Door fitted to the hose reel cabinet. Yes/No/N.A. Yes/No/N.A.

i) Do such doors cause no undue obstruction and no interference with any *Yes/No/N.A. *Yes/No/N.A.
exit point when in open position?

ii) Do such doors cause no obstruction to the hose being run out in either *Yes/No/N.A. *Yes/No/N.A.
direction?

iii) Are the doors of the hose reel cabinets or recesses provided without *Yes/No/N.A. *Yes/No/N.A.
any locks?

iv) Are the doors clearly bear “FIRE HOSE REEL”(消防喉轆) with *Yes/No/N.A. *Yes/No/N.A.
characters of at least 50 mm high?

v) Are control valves and nozzles sited in a discernible and accessible *Yes/No/N.A. *Yes/No/N.A.
position of not more than 500 mm from the surface of the doors?

vi) Are the operation instruction notices fixed immediately below the *Yes/No/N.A. *Yes/No/N.A.
words “FIRE HOSE REEL” on the outer surface of the doors?

3.1.3.5 Rising Mains

a) Are air relief valves provided for rising mains? *Yes/No/N.A. *Yes/No/N.A.

b) Are draining facilities provided at the lowest points of rising mains? *Yes/No/N.A. *Yes/No/N.A.

c) Are the rising mains of the correct sizes? (Industrial/Godown – not less *Yes/No/N.A. *Yes/No/N.A.
than 100 mm nominal bore, Others – not less than 80 mm nominal bore)

Tested / Checked by : Signature - Post :

(Name of Authorised Contractor’s Representative) Tel. No. :
( ) Date :
Witnessed by : Signature - Post :
(Name(s) of *PBSE/PBSI) Tel. No. :
( ) Date :

Annex II T&C Procedure for Fire Service Installation

Page 7 of 194 2022 Edition
(TCP-FS-2022)
Items tested/ Items witnessed
checked by by
Contractor PBSE/PBSI

d) Are the rising mains supply the correct number of hydrant outlets (2 *Yes/No/N.A. *Yes/No/N.A.
outlets per floor for industrial/godown and 1 outlet per floor for other
buildings)?

e) Is each rising main provided with an independent F.S. inlet? *Yes/No/N.A. *Yes/No/N.A.

f) Are rising and down-coming mains permanently primed? Yes/No/N.A. Yes/No/N.A.

g) Is there any provision of by-pass for intermediate booster pump? *Yes/No/N.A. *Yes/No/N.A.

h) Is/Are the Header pipe(s) provided to connect the fire service inlets to the *Yes/No/N.A. *Yes/No/N.A.
rising mains if there is more than 1 rising main in the system?

i) Is/Are the Header pipe(s) with a maximum height of 30 m above ground *Yes/No/N.A. *Yes/No/N.A.
level?

j) Are the rising mains interconnected by header pipes of correct sizes? *Yes/No/N.A. *Yes/No/N.A.
(Industrial/Godown – not less than 150 mm nominal bore, Others – not
less than 100 mm nominal bore).

k) For godown/industrial buildings, is the rising main provided for each *Yes/No/N.A. *Yes/No/N.A.
staircase with a fire service inlet?

l) Are the number and location of fire service inlets conforming to latest *Yes/No/N.A. *Yes/No/N.A.
approved building plan?

Tested / Checked by : Signature - Post :

(Name of Authorised Contractor’s Representative) Tel. No. :
( ) Date :
Witnessed by : Signature - Post :
(Name(s) of *PBSE/PBSI) Tel. No. :
( ) Date :

Annex II T&C Procedure for Fire Service Installation

Page 8 of 194 2022 Edition
(TCP-FS-2022)
3.1.3.6 Fire Pump

a) Pump/Motor Set Data :

Fixed Fire Pump Intermediate Pump Transfer Pump

Duty Standby Duty Standby Duty Standby

Location

Quantity (No(s).)

Pump
Manufacturer
Motor

Pump
Model No.
Motor

Pump
Serial
Motor

Motor Power (kW)

Pump Power (kW)

Flow rate (l/min)

Pressure (kPa)

Starting method

Tested / Checked by : Signature - Post :

(Name of Authorised Contractor’s Representative) Tel. No. :
( ) Date :
Witnessed by : Signature - Post :
(Name(s) of *PBSE/PBSI) Tel. No. :
( ) Date :

Annex II T&C Procedure for Fire Service Installation

Page 9 of 194 2022 Edition
(TCP-FS-2022)
Items tested/ Items witnessed
checked by by
Contractor PBSE/PBSI

b) Is electricity used for driving the pump? If no, please specify. *Yes/No/N.A. *Yes/No/N.A.

c) Is secondary power supply provided for electric pumps? Yes/No/N.A. Yes/No/N.A.

d) If no, is diesel engine driven standby pump provided? Yes/No/N.A. Yes/No/N.A.

e) Are alternative means of starting the pump manually, in addition to *Yes/No/N.A. *Yes/No/N.A.
manual fire alarm call points provided, where the pump is not electrically
operated?

f) Are starting instructions for diesel driven pump prominently displayed in *Yes/No/N.A. *Yes/No/N.A.
the pump room?

g) Are the motor/pump set rotating parts protected by safety guards? *Yes/No/N.A. *Yes/No/N.A.

h) Are pump motors protected by HRC fuses? Yes/No/N.A. Yes/No/N.A.

j) Can the pump just be stopped by switching off at the pump control *Yes/No/N.A. *Yes/No/N.A.
installed near the pump, rather than by any automatic means?

j) Are manual fire alarm call points wired for starting the pump? *Yes/No/N.A. *Yes/No/N.A.

k) Are the pumps duplicated for duty and standby use? *Yes/No/N.A. *Yes/No/N.A.

l) Are the fire pump starters wired through a selector switch for duty and *Yes/No/N.A. *Yes/No/N.A.
standby pump selection?

m) Are pumps permanently primed? Yes/No/N.A. Yes/No/N.A.

n) Are non-return valve(s) provided to prevent water backflow into the water *Yes/No/N.A. *Yes/No/N.A.
tank?

o) Is pump motor power rated at 20% higher than the required hydraulic *Yes/No/N.A. *Yes/No/N.A.
power for the rated flow of the system?

p) Are emergency lock-off buttons provided adjacent to pump motors with *Yes/No/N.A. *Yes/No/N.A.
visual and audible indication on the panel with a common fault signal
repeated at the main fire control panel when the pump is locked?

q) Are the status of each fire pump comprising “Power Supply On”, “Pump *Yes/No/N.A. *Yes/No/N.A.
Running” and “Pump Failed” monitored and displayed at the pump control
panel in the pump room?

r) Are such signals repeated to fire control room or a status panel at the main *Yes/No/N.A. *Yes/No/N.A.
entrance of the building?

s) Are all fire pumps housed in suitable enclosures and designed solely for *Yes/No/N.A. *Yes/No/N.A.
accommodating pumps for fire service installations?

t) Are pump enclosures clearly marked in English and Chinese characters? *Yes/No/N.A. *Yes/No/N.A.

Tested / Checked by : Signature - Post :

(Name of Authorised Contractor’s Representative) Tel. No. :
( ) Date :
Witnessed by : Signature - Post :
(Name(s) of *PBSE/PBSI) Tel. No. :
( ) Date :

Annex II T&C Procedure for Fire Service Installation

Page 10 of 194 2022 Edition
(TCP-FS-2022)
Items tested/ Items witnessed
checked by by
Contractor PBSE/PBSI

u) Are the pumps enclosures suitably locked to prevent unauthorised *Yes/No/N.A. *Yes/No/N.A.
tampering of the pumps?

v) Are doors to pump rooms provided with automatic door closers? *Yes/No/N.A. *Yes/No/N.A.

w) Are pump rooms laid clear of any exit or normal communication routes *Yes/No/N.A. *Yes/No/N.A.
through the premises?

x) Are pump rooms clear of debris? Yes/No/N.A. Yes/No/N.A.

y) Are doors to pump rooms clearly labelled “FIXED FIRE PUMP” (消防 *Yes/No/N.A. *Yes/No/N.A.
泵) *and/or “INTERMEDIATE BOOSTER FIRE PUMP” (中途泵)?

z) Are the running and static pressure at any hydrant outlet not exceeding *Yes/No/N.A. *Yes/No/N.A.
850kPa?

3.1.3.7 Intermediate booster pump

a) Height between the topmost hydrant and the lowest F.S. inlet (m): ____________ _____________

b) No. of rising main: _

c) Required aggregate flow (l/min): _

d) Are the pumps duplicated for duty and standby use? *Yes/No/N.A. *Yes/No/N.A.

i) Is one set of intermediate booster pumps consisting of duty and standby *Yes/No/N.A. *Yes/No/N.A.
to feed all rising mains in the same system?

ii) Are two/three pumps of same capacity provided using sequential *Yes/No/N.A. *Yes/No/N.A.
starting as duty pumps with one standby to achieve required flow and
pressure within 30 seconds?

e) Is the standby pump energised within 15 seconds upon failure of the duty *Yes/No/N.A. *Yes/No/N.A.
pump and take over the role of duty pump?

f) Are the motors driving the pumps rated to give 20% more power in *Yes/No/N.A. *Yes/No/N.A.
addition to the hydraulic power required for the rated flow?

g) Are all pumps permanently primed and electrically driven? *Yes/No/N.A. *Yes/No/N.A.

h Does the pump continue to run irrespective of power interruption when *Yes/No/N.A. *Yes/No/N.A.
start button is activated?

i) Are the Start/stop push buttons with pump status indicator lights *Yes/No/N.A. *Yes/No/N.A.
(comprising “power supply on”, “pump running” and “pump failed”
indicators for each pump) and alarm buzzer provided adjacent to the fire
service inlets?

Tested / Checked by : Signature - Post :

(Name of Authorised Contractor’s Representative) Tel. No. :
( ) Date :
Witnessed by : Signature - Post :
(Name(s) of *PBSE/PBSI) Tel. No. :
( ) Date :

Annex II T&C Procedure for Fire Service Installation

Page 11 of 194 2022 Edition
(TCP-FS-2022)
Items tested/ Items witnessed
checked by by
Contractor PBSE/PBSI

j) Are the above switches clearly labelled in English and Chinese characters *Yes/No/N.A. *Yes/No/N.A.
“INTERMEDIATE BOOSTER PUMP CONTROL" (中途泵開關掣) of
at least 5 mm high?

k) Are the status of each fire pump comprising “Power Supply On”, “Pump *Yes/No/N.A. *Yes/No/N.A.
Running” and “Pump Failed” monitored and displayed at the pump control
panels in the pump enclosures?

l) Are such signals repeated to fire control room or a status panel at the main *Yes/No/N.A. *Yes/No/N.A.
entrance of the building?

m) Are all fire pumps housed in suitable enclosures and designed solely for *Yes/No/N.A. *Yes/No/N.A.
accommodating pumps for fire service installations?

n) Are the pump enclosures suitably locked and laid clear of any exit or *Yes/No/N.A. *Yes/No/N.A.
normal communication routes through the premises?

o) Are the pump enclosures clearly marked in English and Chinese *Yes/No/N.A. *Yes/No/N.A.
characters?

p) Is the intermediate booster pump utilised as the fixed fire pump? *Yes/No/N.A. *Yes/No/N.A.

q) Do the running and static pressure at any hydrant outlet not exceeding 850 *Yes/No/N.A. *Yes/No/N.A.
kPa?

3.1.3.8 Fire Service Inlet

a) Are the fire service inlet couplings between 600 mm and 1000 mm above *Yes/No/N.A. *Yes/No/N.A.
finished floor level?

b) Are the fire service inlets suitably enclosed and protected? *Yes/No/N.A. *Yes/No/N.A.

c) Are the fire service inlets readily accessible by Fire Services personnel? *Yes/No/N.A. *Yes/No/N.A.

d) Is a non-return valve provided for each inlet? Yes/No/N.A. Yes/No/N.A.

e) Are the fire service inlet enclosures clearly and permanently labelled “F.S. *Yes/No/N.A. *Yes/No/N.A.
INLET” (消防入水掣) with characters at least 50 mm high?

f) Is each inlet affixed with a metal identification plate raised on engraved *Yes/No/N.A. *Yes/No/N.A.
with English and Chinese characters?

3.1.3.9 Miscellaneous

a) Are all pipeworks and metal works properly painted? *Yes/No/N.A. *Yes/No/N.A.

b) Is proper identification provided for pipeworks, wirings and equipment? *Yes/No/N.A. *Yes/No/N.A.

Tested / Checked by : Signature - Post :

(Name of Authorised Contractor’s Representative) Tel. No. :
( ) Date :
Witnessed by : Signature - Post :
(Name(s) of *PBSE/PBSI) Tel. No. :
( ) Date :

Annex II T&C Procedure for Fire Service Installation

Page 12 of 194 2022 Edition
(TCP-FS-2022)
Items tested/ Items witnessed
checked by by
Contractor PBSE/PBSI

3.1.4 Testing and Commissioning

3.1.4.1 Pipeworks

a) Are hydraulic tests performed satisfactorily for water tightness of all *Yes/No/N.A. *Yes/No/N.A.
sections of the pipeworks? (Test records on Part 4.1 Table 1)

b) Is flushing out of all water pipes performed? Yes/No/N.A. Yes/No/N.A.

c) Is flushing out of all hose reel tubing performed? Yes/No/N.A. Yes/No/N.A.

d) Do the automatic air release valves function properly? Yes/No/N.A. Yes/No/N.A.

e) Do the pressure reducing valve sets function properly? (Test records on *Yes/No/N.A. *Yes/No/N.A.
Part 4.1 Table 2)

f) Do the gate valves, stop valves and globe valves function properly? *Yes/No/N.A. *Yes/No/N.A.

3.1.4.2 Electrical Wiring

a) Is the electrical wiring system tested satisfactorily in accordance with the *Yes/No/N.A. *Yes/No/N.A.
T&C Procedure for Electrical Installation and to Electricity Ordinance
requirements?

b) Does the battery charger function properly? Yes/No/N.A. Yes/No/N.A.

c) Is the telephone link connected and functioning? Yes/No/N.A. Yes/No/N.A.

d) Is permanent electricity supply connected? Yes/No/N.A. Yes/No/N.A.

e) Is emergency electricity supply available? Yes/No/N.A. Yes/No/N.A.

3.1.4.3 Fire Pump

a) Do the pumps and motors run at the designed discharge water pressure and *Yes/No/N.A. *Yes/No/N.A.
operating electrical current? (Test records on Part 4.1 Table 3)

b) Do the pumps run at an acceptable noise and vibration levels? *Yes/No/N.A. *Yes/No/N.A.

c) Do the pump control switches and indicating lights function properly? *Yes/No/N.A. *Yes/No/N.A.

d) Do the pump protective devices function properly? Yes/No/N.A. Yes/No/N.A.

e) Do the fixed fire pumps come into operation upon actuation of any manual *Yes/No/N.A. *Yes/No/N.A.
fire alarm call point, regardless of the zoning of the fire alarm call point?

Tested / Checked by : Signature - Post :

(Name of Authorised Contractor’s Representative) Tel. No. :
( ) Date :
Witnessed by : Signature - Post :
(Name(s) of *PBSE/PBSI) Tel. No. :
( ) Date :

Annex II T&C Procedure for Fire Service Installation

Page 13 of 194 2022 Edition
(TCP-FS-2022)
Items tested/ Items witnessed
checked by by
Contractor PBSE/PBSI

f) Are the status of fire pumps including “power supply on”, “pump running” *Yes/No/N.A. *Yes/No/N.A.
and pump failed” displayed at the pump control panel and repeated at the
main fire service control panel?

g) Do the float switches in the water tanks for controlling the transfer pumps *Yes/No/N.A. *Yes/No/N.A.
function properly?

h) Do the high and low water level alarms and indications for the water tanks *Yes/No/N.A. *Yes/No/N.A.
function properly?

i) Are the temperatures of the pump bearings satisfactorily at running *Yes/No/N.A. *Yes/No/N.A.
condition?

j) Are the temperatures of the pump motors satisfactorily at running *Yes/No/N.A. *Yes/No/N.A.
condition?

k) Do the pressure gauges function properly? Yes/No/N.A. Yes/No/N.A.

l) Is water leakage from the pump shafts at an acceptable level? *Yes/No/N.A. *Yes/No/N.A.

m) Do the non-return valves function properly? Yes/No/N.A. Yes/No/N.A.

n) Does the pressure relief valve of the anti-overheating circulating pipe *Yes/No/N.A. *Yes/No/N.A.
function properly? (Operate at _______ kPa)

o) Do the pressure switches controlling the duty and standby pumps operate *Yes/No/N.A. *Yes/No/N.A.
properly? (Test records on Part 4.1 Table 4)

p) Is the standby pump energised within 15 second upon electrical and *Yes/No/N.A. *Yes/No/N.A.
mechanical failure of the duty pump and take over the role of duty pump?

q) Is the duty pump maintained in operation in case of power changeover? *Yes/No/N.A. *Yes/No/N.A.

3.1.4.4 Fire Service Inlet

a) Do the non-return valves of the F.S. inlets function properly? *Yes/No/N.A. *Yes/No/N.A.

b) Do the stop/start buttons, indicating lights and audible alarms for the *Yes/No/N.A. *Yes/No/N.A.
intermediate booster pumps function properly?

c) Do the drain valves function properly? Yes/No/N.A. Yes/No/N.A.

3.1.4.5 Hose reel

a) Can the hose reel tubing be drawn out freely and easily in any direction *Yes/No/N.A. *Yes/No/N.A.
without obstruction?

b) Are the hose reels capable to cover within 6 m of each part of the occupied *Yes/No/N.A. *Yes/No/N.A.
area? (Test Records on Part 4.1 Table 5)

Tested / Checked by : Signature - Post :

(Name of Authorised Contractor’s Representative) Tel. No. :
( ) Date :
Witnessed by : Signature - Post :
(Name(s) of *PBSE/PBSI) Tel. No. :
( ) Date :

Annex II T&C Procedure for Fire Service Installation

Page 14 of 194 2022 Edition
(TCP-FS-2022)
Items tested/ Items witnessed
checked by by
Contractor PBSE/PBSI

c) Are the hose reels capable to project a water jet of 6 m or greater? (Test *Yes/No/N.A. *Yes/No/N.A.
Records on Part 4.1 Table 5)

d) Is the water tightness of the stop valves, nozzles, and tubing connections *Yes/No/N.A. *Yes/No/N.A.
satisfactory when the fire pump is running?

3.1.4.6 Fire Hydrant

a) Is the water tightness of the hydrant outlet satisfactory when the water *Yes/No/N.A. *Yes/No/N.A.
pump is running?

b) Do the flow capacity and pressure test satisfy Fire Services Department’s *Yes/No/N.A. *Yes/No/N.A.
requirements as the following Table? (Test records on Part 4.1 Tables 6, 7
and 8)

Rising Main With fixed fire pump

Building Type No. of hydrant outlet Minimum aggregate flow
Running Pressure (kPa)
operating rate (l/min)

Industrial 1 or more 3 350 – 850 1350

All other types 1 or more 2 350 – 850 900

Rising Main With intermediate booster pump

Building Type No. of hydrant outlet Minimum aggregate flow
Running Pressure (kPa)
operating rate (l/min)

Industrial 1 3 350 – 850 1350

2 or more 6 350 – 850 2700

Domestic 1 or more 2 350 – 850 900

All other types 1 2 350 – 850 900

2 or more 4 350 – 850 1800

Note:
a) Each hydrant outlet shall have a flow of 450 L/min at a running pressure of not less than 350 kPa.
b) The running and static pressure at any fire hydrant outlet shall in no case exceed 850 kPa.

Tested / Checked by : Signature - Post :

(Name of Authorised Contractor’s Representative) Tel. No. :
( ) Date :
Witnessed by : Signature - Post :
(Name(s) of *PBSE/PBSI) Tel. No. :
( ) Date :

Annex II T&C Procedure for Fire Service Installation

Page 15 of 194 2022 Edition
(TCP-FS-2022)
Items tested/ Items witnessed
checked by by
Contractor PBSE/PBSI

3.2 Automatic Sprinkler System

3.2.1 Visual Inspection

3.2.1.1 Water Supplies

a) Is an independent town main connection provided for the sprinkler system *Yes/No/N.A. *Yes/No/N.A.
installation alone?

b) Does the size of the incoming water pipe from the town mains up to the *Yes/No/N.A. *Yes/No/N.A.
sprinkler tank tally with the vertical plumbing diagram approved by
W.S.D.?

c) Is the effective water capacity correct of the :

(i) Sprinkler tank? Yes/No/N.A. Yes/No/N.A.

(ii) Transfer tank? *Yes/No/N.A. *Yes/No/N.A.
(iii) Priming tank? *Yes/No/N.A. *Yes/No/N.A.

d) Is an indication given before a water storage level drops more than 10% *Yes/No/N.A. *Yes/No/N.A.
below its normal fill level?

e) Are the ball valves of the water tank readily accessible? *Yes/No/N.A. *Yes/No/N.A.

f) Positive suction head:

(i) Is there at least two-thirds of the effective capacity of the suction *Yes/No/N.A. *Yes/No/N.A.
tank above the level of the pump centre-line? AND

(ii) Is the pump centre-line not more than 2m above the low water level *Yes/No/N.A. *Yes/No/N.A.
of the suction tank?
(Remark: If the above conditions cannot be fulfilled, the pumps are
in suction lift conditions.)

(iii) Is the nominal diameter of suction pipe under positive suction *Yes/No/N.A. *Yes/No/N.A.
correct? (LH – min. 65 mm dia., OH1&2 – min. 150 mm dia., OH3
& 4 – min. 200 mm dia)

g) Suction lift condition:

(i) Is each water pump provided with an independent suction pipe? *Yes/No/N.A. *Yes/No/N.A.

(ii) Is the nominal diameter of suction pipe under suction lift condition *Yes/No/N.A. *Yes/No/N.A.
correct? (LH – min. 80 mm dia., OH1&2 – min. 150 mm dia., OH3
& 4 – min. 200 mm dia)

(iii) Are automatic priming arrangements provided for suction lift *Yes/No/N.A. *Yes/No/N.A.
condition?

(iv) Are sizes of priming water pipes correct? (LH – min. 25 mm dia., *Yes/No/N.A. *Yes/No/N.A.
OH and HH – min. 50 mm dia.)

Tested / Checked by : Signature - Post :

(Name of Authorised Contractor’s Representative) Tel. No. :
( ) Date :
Witnessed by : Signature - Post :
(Name(s) of *PBSE/PBSI) Tel. No. :
( ) Date :

Annex II T&C Procedure for Fire Service Installation

Page 16 of 194 2022 Edition
(TCP-FS-2022)
Items tested/ Items witnessed
checked by by
Contractor PBSE/PBSI

(v) Is each water pump provided with an independent priming tank? *Yes/No/N.A. *Yes/No/N.A.
(LH – min. 100 litres, OH and HH – min. 500 litres)

h) Is the equivalent length of the suction pipe and fittings not more than *Yes/No/N.A. *Yes/No/N.A.
30m?

i) Are levels of suction pipes correct? Yes/No/N.A. Yes/No/N.A.

j) Are puddle flanges of the same size as the water pump suction pipes? *Yes/No/N.A. *Yes/No/N.A.

k) Is a foot valve or check valve fitted to the suction pipe where not less than *Yes/No/N.A *Yes/No/N.A
one-sixth of the effective stored capacity contained below the centre-line
of the pump and the low water level X?

l) Is anti-overheating circulating pipe provided? Yes/No/N.A. Yes/No/N.A.

m) Is vertex inhibitor provided and clear of debris? Yes/No/N.A. Yes/No/N.A.

n) Are strainers in water tank cleaned? Yes/No/N.A. Yes/No/N.A.

o) Is the tank clear of debris? Yes/No/N.A. Yes/No/N.A.

p) Has the Fire Service Completion Advice issued? Yes/No/N.A. Yes/No/N.A.

3.2.1.2 Spacing and Location of Sprinklers

a) Are spacing and location of sprinkler heads in accordance with LPC Rules
regarding :

(i) Area of coverage? Yes/No/N.A. Yes/No/N.A.

(ii) Maximum distance between sprinklers? Yes/No/N.A. Yes/No/N.A.

(iii) Minimum distance between sprinklers? Yes/No/N.A. Yes/No/N.A.

(iv) Distance from wall/partition? Yes/No/N.A. Yes/No/N.A.

(v) Distance from open face of building? Yes/No/N.A. Yes/No/N.A.

(vi) Distance from beam? Yes/No/N.A. Yes/No/N.A.

(vii) Distance from column? Yes/No/N.A. Yes/No/N.A.

(viii) Clear space below sprinklers? Yes/No/N.A. Yes/No/N.A.

(ix) Depth of ceiling void? Yes/No/N.A. Yes/No/N.A.

(x) Obstruction below sprinklers? Yes/No/N.A. Yes/No/N.A.

(xi) Canopy? Yes/No/N.A. Yes/No/N.A.

Tested / Checked by : Signature - Post :

(Name of Authorised Contractor’s Representative) Tel. No. :
( ) Date :
Witnessed by : Signature - Post :
(Name(s) of *PBSE/PBSI) Tel. No. :
( ) Date :

Annex II T&C Procedure for Fire Service Installation

Page 17 of 194 2022 Edition
(TCP-FS-2022)
Items tested/ Items witnessed
checked by by
Contractor PBSE/PBSI

(xii) Are construction of open ceiling spacing and location of sprinkler *Yes/No/N.A. *Yes/No/N.A.
heads in accordance with LPC Rules?

1) Open area of ceiling? (Not less than 70% open area including light *Yes/No/N.A. *Yes/No/N.A.
fittings)

2) Dimensions of opening? (Not less than 0.025m or not less than the *Yes/No/N.A. *Yes/No/N.A.
depth of the ceiling)

3) Distance of sprinklers? (Not exceed 3m) Yes/No/N.A. Yes/No/N.A.

4) Vertical separation between sprinklers and ceiling? (Not less than *Yes/No/N.A. *Yes/No/N.A.
0.3 m for flat spray sprinkler and not less than 0.8 m for sprinklers
other than flat spray sprinklers)

b) Is there any sheet metal or fire resistance sheet not less than 200mm wide *Yes/No/N.A. *Yes/No/N.A.
and 150mm high located midway between the sprinklers or by using
intervening construction features when there is possibility for adjacent
sprinklers from wetting each other?

c) Are there any baffles with its top edge extend above the sprinkler deflector *Yes/No/N.A. *Yes/No/N.A.
by 50mm to 75mm if the baffles are fitted on the range pipe when there is
possibility for adjacent sprinklers from wetting each other?

3.2.1.3 Sprinkler Heads

a) Are sprinklers clean from contamination by paint, etc.? Yes/No/N.A. Yes/No/N.A.

b) Are sprinklers of correct nominal K factor in accordance with LPC rules? *Yes/No/N.A. *Yes/No/N.A.

c) Are sprinklers of correct temperature ratings? (68oC red bulb for normal *Yes/No/N.A. *Yes/No/N.A.
use, 93oC green bulb for skylight)

d) Are replacement sprinklers provided and completed with cabinets? (LH *Yes/No/N.A. *Yes/No/N.A.
- 6 Nos., OH - 24 Nos. & HH - 36 Nos. For more than 2 installations,
added 50% to the figures.)

e) Is there a stock of spare sprinklers kept in the Fire Control Room of the *Yes/No/N.A. *Yes/No/N.A.
premises adequate for operated or damaged sprinklers?

f) Is sprinkler spanner provided and kept in sprinkler cabinet? Yes/No/N.A. Yes/No/N.A.

g) Is the cabinet or cabinets located in a prominent and easily accessible *Yes/No/N.A. *Yes/No/N.A.
position where the ambient temperature does not exceed 40oC?

h) Are sprinkler guards provided at locations where the sprinklers are at a *Yes/No/N.A. *Yes/No/N.A.
height less than 2 m from ground level or liable to damage?

i) Are the Nos. of sprinklers installed on the range and distribution pipes in *Yes/No/N.A. *Yes/No/N.A.
accordance with LPC Rules?

Tested / Checked by : Signature - Post :

(Name of Authorised Contractor’s Representative) Tel. No. :
( ) Date :
Witnessed by : Signature - Post :
(Name(s) of *PBSE/PBSI) Tel. No. :
( ) Date :

Annex II T&C Procedure for Fire Service Installation

Page 18 of 194 2022 Edition
(TCP-FS-2022)
Items tested/ Items witnessed
checked by by
Contractor PBSE/PBSI

j) Are sprinklers installed in upright position for either type of pre-action *Yes/No/N.A. *Yes/No/N.A.
installation unless otherwise recommended by the corresponding
manufacturer of the installation?

k) Are sprinkler heads installed in upright position for dry pipe system *Yes/No/N.A. *Yes/No/N.A.
installations in cold room?

3.2.1.4 Pipeworks

a) Are water pipes up to 150 mm dia. to BS EN 10255 / ISO 65 / BS EN Yes/No/N.A. Yes/No/N.A.

10217-1 medium grade or other approved type?

b) Are water pipes larger than 150 mm dia. to BS EN 545 Class 64 (dia. 200 *Yes/No/N.A. *Yes/No/N.A.
– 350) or Class 50 (dia. 400 – 600) or other approved type?

c) Are U/G water pipes to BS EN 545 Class 100 (dia. 80 -150), Class 64 (dia. *Yes/No/N.A. *Yes/No/N.A.
200 – 350) or Class 50 (dia. 400 – 600) or to BS EN 10255 / ISO 65 heavy
grade or other approved type?

d) Are U/G water pipes protected with two coats of bituminous paint and *Yes/No/N.A. *Yes/No/N.A.
wrapped with self-amalgamating tapes and mastics having minimum 55%
overlapping?

e) Are water pipes up to 50 mm dia. operating at working pressure not *Yes/No/N.A. *Yes/No/N.A.
exceeding 1600 kPa provided with screw joints?

f) Are water pipes of dia. larger than 50 mm and up to 150 mm operating on *Yes/No/N.A. *Yes/No/N.A.
or below 1600 kPa provided with mechanical pipe couplings or screwed
joints?

g) Are water pipes of dia. larger than 150 mm provided with flanged joints *Yes/No/N.A. *Yes/No/N.A.
and flanged fittings?

h) Are U/G water pipes provided with mechanical pipe couplings or other *Yes/No/N.A. *Yes/No/N.A.
approved couplings?

i) Are water pipes provided with adequate disconnecting flanges, *Yes/No/N.A. *Yes/No/N.A.
mechanical pipe couplings or screwed unions for future ease of
dismantling?

j) Are pipes suitably connected to the sprinkler pumps, sprinkler control *Yes/No/N.A. *Yes/No/N.A.
valves and sprinkler inlets?

k) Are bends of water pipes larger than 50 mm dia. and bends of water pipes *Yes/No/N.A. *Yes/No/N.A.
installed outside false ceiling/concealed void of long radius type, or as
approved?

l) Are galvanised mild steel sleeves provided for pipes through wall or slab? *Yes/No/N.A. *Yes/No/N.A.

m) Are spaces between water pipes and pipe sleeves through wall or slab *Yes/No/N.A. *Yes/No/N.A.
filled with approved fire proof material and sealant?

Tested / Checked by : Signature - Post :

(Name of Authorised Contractor’s Representative) Tel. No. :
( ) Date :
Witnessed by : Signature - Post :
(Name(s) of *PBSE/PBSI) Tel. No. :
( ) Date :

Annex II T&C Procedure for Fire Service Installation

Page 19 of 194 2022 Edition
(TCP-FS-2022)
Items tested/ Items witnessed
checked by by
Contractor PBSE/PBSI