Scribd
Upload
33 views

1.dynamic Characteristics Introduction

This document discusses the dynamic characteristics of instruments when subjected to changing input signals over time. It describes how instruments do not instantly reach their final output but instead go through a transient state before settling. The dynamic response and characteristics are important when inputs are dynamic rather than static. Key dynamic characteristics discussed include response time, lag, fidelity, and dynamic error. The document also covers different types of dynamic inputs like step, linear, and sinusoidal and how instruments respond to each.

Uploaded by

World Today
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
33 views

1.dynamic Characteristics Introduction

This document discusses the dynamic characteristics of instruments when subjected to changing input signals over time. It describes how instruments do not instantly reach their final output but instead go through a transient state before settling. The dynamic response and characteristics are important when inputs are dynamic rather than static. Key dynamic characteristics discussed include response time, lag, fidelity, and dynamic error. The document also covers different types of dynamic inputs like step, linear, and sinusoidal and how instruments respond to each.

Uploaded by

World Today
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 20

Dynamic Characteristics of

Instruments

B Tech 4 th Semester
Instrumentation and control

Mechanical Engineering
Transient Response
➢When an input is applied to an instrument or a
measurement system, the instrument or the system
cannot take up immediately its final steady state
position.
➢It goes through a transient state before it finally
settles to its final “steady state” position.
➢Some of the measurements are made under such
conditions as to allow the sufficient time for the
instrument or the measurement system to settle to its
final steady state conditions.
➢Under such conditions the study of behaviour of the
system under transient state, known as “transient
response” is not of much of importance.
➢However, in many areas of measurement systems
applications it becomes necessary to study the response
of the system under both transient as well as steady
state conditions.
➢In many applications, the transient response of the
system, i.e., the way system settles down to its final
steady state conditions is more important than the
steady state response.
➢The transient response in the instruments is on
account of the presence of energy storage elements in
the system, such as, electrical inductance and
capacitance, mass, fluid and thermal capacitances etc.
➢The systems exhibit a characteristic of sluggishness
or slowness on account of presence of these elements.
Dynamic Response &Characteristics
➢In several applications the measurement
systems are subjected to inputs which are not
static but dynamic in nature, which means the
inputs vary with time. Since the input varies
from instant to instant, so does the output.
➢The behaviour of the system under such
conditions is described by the dynamic
response of the system and the characteristics
of the measuring system under such conditions
are known as dynamic characteristics.
Dynamic Characteristics :
The set of criteria defined for the instruments,
which are changes rapidly with time, is called
‘dynamic characteristics’.
Dynamic characteristics of a measuring instrument
refer to the case where the measured variable
changes rapidly.
As in case of sensors in control system cannot react
to a sudden change in measured variable
immediately. A certain amount of time is required
before the measuring instrument in control system
technology can indicate any output based on the
input received by the measuring instrument.
The dynamic behaviour of the measuring instruments
is judged for the following three types of inputs -
(i) Step Input
(ii) Linear Input
(iii) Sinusoidal Input

(i) Step Input- In this case, the input changes


instantaneously by a finite value and then remains
constant.
(ii) Linear Input- In this case, the input changes linearly
with time
(iii) Sinusoidal Input- In this case, the input changes
according to a sinusoidal function of constant amplitude.
The dynamic characteristics of any measurement
system are:
(i) Speed of response and Response time
(ii) Lag
(iii) Fidelity
(iv) Dynamic error
Out of the above four characteristics the
Speed of Response and the Fidelity are desirable in a
dynamic system,
while Lag and Dynamic error are undesirable.
Speed of Response & Response Time
➢Speed of Response is defined as the rapidity with
which an instrument or measurement system
responds to changes in measured quantity.
➢Response Time is the time required by instrument
or system to settle to its final steady position after
the application of the input.
➢For a step input function, the response time may be
defined as the time taken by the instrument to settle
to a specified percentage of the quantity being
measured, after the application of the input.
➢This percentage may be 90 to 99 percent depending
upon the instrument.
➢For portable instruments it is the time taken by the
pointer to come to rest within 0.3 percent of final scale
length.
➢For switch board (panel) type of instruments it is the
time taken by the pointer to come to rest within 1 percent
of its final scale length.
Measuring Lag
➢ The delay in the response of an instrument to a
change in the measured quantity is known
as measuring lag.
➢This lag is usually quite small, but this small
lag becomes highly important when high speed
measurements are required.
➢In the high speed measurement systems, as in
dynamic measurements, it becomes essential
that the time lag be reduced to minimum.
Measuring lag is of two types :
i) Retardation type: In this type of measuring
lag the response begins immediately after a
change in measured quantity has occurred.

ii) Time delay: In this type of measuring lag the


response of the measurement system begins after
a dead zone after the application of the input
Fidelity
• Fidelity of a system is defined as the ability of the
system to reproduce the output in the same form as the
input.
• It is the degree to which a measurement system
indicates changes in the measured quantity without
any dynamic error.
• Supposing if a linearly varying quantity is applied to a
system and if the output is also a linearly varying
quantity the system is said to have 100 percent fidelity.
• Ideally a system should have 100 percent fidelity and
the output should appear in the same form as that of
input and there is no distortion produced in the signal
by the system. In the definition of fidelity any time lag
or phase difference between output and input is not
included.
Dynamic Error
➢ The dynamic error is the difference between the true value
of the quantity changing with time and the value indicated
by the instrument if no static error is assumed.
• However, the total dynamic error of the
instrument is the combination of its fidelity
and the time lag or phase difference between
input and output of the system.
Overshoot
Moving parts of instruments have mass and thus
possess inertia. When an input is applied to
instruments, the pointer does not immediately come
to rest at its steady state (or final deflected) position
but goes beyond it or in other words overshoots its
steady position.
• The overshoot is evaluated as the maximum
amount by which moving system moves beyond
the steady state position. In many instruments,
especially galvanometers it is desirable to have
a little overshoot but an excessive overshoot is
undesirable.
Thank You

You might also like