Scribd
Upload
178 views1 page

Base Plate Design

The document summarizes the design of a base plate (BP1) for a truss with the following key details: 1. The critical load combination is 36 kN with axial and bending forces of 61.34 kN and 0.006 kN-m respectively. 2. The required base plate thickness is calculated to be 3.19 mm but a minimum of 5.44 mm is required, so an 8 mm thick plate is selected. 3. Four 12 mm diameter anchor bolts are selected to support the 61.34 kN axial load safely in single shear.

Uploaded by

Jimit Pay
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
178 views1 page

Base Plate Design

The document summarizes the design of a base plate (BP1) for a truss with the following key details: 1. The critical load combination is 36 kN with axial and bending forces of 61.34 kN and 0.006 kN-m respectively. 2. The required base plate thickness is calculated to be 3.19 mm but a minimum of 5.44 mm is required, so an 8 mm thick plate is selected. 3. Four 12 mm diameter anchor bolts are selected to support the 61.34 kN axial load safely in single shear.

Uploaded by

Jimit Pay
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Rev DATE

Project :- ODU Structure 0 17-03-2021

Base Plate Design (BP1)


Node No 62
Critical Load Combination 36 300 mm
At Truss End forces from Staad
Axial Force, Fx = 61.334 kN
Moment, My = 0.006 kN-m

200 mm

300 mm
= b
Moment, Mz 0 kN-m

100
Grade of Concrete = 30 N/mm2
Yield Strength of Steel, fy = 250 N/mm2

a
Section used SHS 100X100X6 = 100 x 100 x mm
Assume Size of Column below bearing plate = 300 x 300 mm 200 mm
Assume , Size of Bearing Plate = 200 x 200 mm
Thickness of flange, tf = 8 mm
Area of Bearing Plate, A = 40000 mm2
Section Modulus of base plate = 1333333 mm3
Distance, a = 50 mm
Distance, b = 50 mm
Bending Moment at the face of the Base plate,
= 0.38446 kN-m
M

Intensity of Pressure on base plate = (P/A)+(My/Z)+(Mz/Z)


= 1.53785 N/mm2

Max allowable Pressure pressure = 2.46475 N/mm2

Hence ok
Design Bending Stress = 227.273 N/mm2

Thickness of Base plate required, treq. = 3.18588 mm

Min. Thickness required for base plate as per IS


= 5.44092 mm
800 :2007

Provide Base Plate thickness = 8 mm (At lesast equal to the thickness of flange )

Hence Safe
Required Base Plate Size is 200 x 200 x 8 mm
Provide Base Plate Size is 200 x 200 x 16 mm

Anchor Bolt Design

No of bolts consider on each row = 2


No of rows of bolts = 2
No of bolts consider on each row = 0
No of rows of bolts = 0
Axial force, Fx = 61.334 kN
Moment, My = 0.006 kN-m
Moment, Mz = 0 kN-m
Distance Between two bolts in a row = 200 mm
Distance Between two bolts in a row = -200 mm
Load coming on each bolt due to bi-axial moment = 0.001 kN
Total Load coming on each bolt = 15.334 kN
Grade of Bolts = 4.400

Ultimate Strength of Bolts = 400 N/mm2


Assume dia of bolt = 12 mm
Tensile Capacity of one bolt = 25.4164 kN
Strength of Bolt in single shear, Vdb = 16.3046 kN
Hence ok
Provide 4 No of Bolts of 12 mm dia.

You might also like