SP40S

Multi-Function Facility
Communication System

Installation, Testing,
Operation and
Maintenance Manual

Part Number P84714 Revision P

Assembly Number A84715-001 Revision C
Copyright 2018 Cooper Wheelock, dba Cooper Notification. All Rights Reserved.
SP40S Multi-Function Facility Communications System 2
About Cooper Notification:
Cooper Notification fulfills its mission of
Helping People Take Action by
providing high quality and advanced
products and services for the life safety,
communications, and security markets.
Cooper Notification has served the
needs of commercial, educational,
industrial, health care, and government
users for more than eighty-five years.
Today the company continues to focus
on designing and manufacturing
advanced technological products to
meet the world’s needs for Emergency
Incident Management and Notification,
Multi-Function Communications, and
Mass Notification.

For more information, contact: Cooper Notification

273 Branchport Avenue
Long Branch, NJ 07740-6899
Telephone: (800) 631.2148
Fax: (732) 222.2588
Web Site: www.coopernotification.com
E-Mail: [email protected]

SP40S Multi-Function Facility Communications System 3

SP40S Multi-Function Communication System 4
 Table of Contents

1. Forward 13
1.1 Intended use .................................................................................................... 13
1.2 Design Change Disclaimer ............................................................................. 13
1.3 User Operation Assistance.............................................................................. 13
1.4 Product Model Descriptions ........................................................................... 13
1.5 Typographical Notation Conventions ............................................................. 13
2. Safety Precautions 15
2.1 Read This Manual........................................................................................... 15
2.2 Operational Safety .......................................................................................... 15
2.2.1 Expected Equipment Lifecycle ............................................................ 16
2.2.2 Periodic Testing ................................................................................... 16
2.3 Compliance with Applicable Codes, Regulations, Laws, Standards, and
Guidelines ...................................................................................................... 16
2.4 Insurance Recommendation ........................................................................... 17
2.5 Audio Output Considerations ......................................................................... 17
2.6 RF Interference ............................................................................................... 18
2.7 General ........................................................................................................... 18
3. Overview 19
3.1 Compatibility with Existing Safepath Products.............................................. 19
3.2 Standard Features ........................................................................................... 19
3.3 Enclosure and Configuration .......................................................................... 21
3.4 Nominal Electrical Data ................................................................................. 21
3.5 User Interface ................................................................................................. 22
3.5.1 Basic Operation of User Interface ........................................................ 23
3.5.2 Overview .............................................................................................. 23
3.6 Additional Drawings....................................................................................... 25
3.7 User Settings ................................................................................................... 30
3.7.1 Switch Descriptions ............................................................................. 30
3.7.2 Jumper Descriptions............................................................................. 32
3.8 LED Descriptions ........................................................................................... 33
4. Installation 34
4.1 Introduction .................................................................................................... 34
4.2 Fire Alarm Control Panel Wiring Applications .............................................. 34
4.3 General Installation Instructions ..................................................................... 35
4.4 Preparing the System Wiring Diagram ........................................................... 38
4.4.1 Unpacking and Taking Inventory......................................................... 38
4.4.2 Locating the Panel................................................................................ 38
4.4.3 Installing Field Wiring Connections .................................................... 40
4.4.4 Installing Strobe Connections .............................................................. 41
4.4.5 Installing Audio Output Connections................................................... 42
4.4.6 Installing Auxiliary Circuit Connections ............................................. 43

SP40S Multi-Function Communication System 5

 4.4.7 Installing Audio Input Connections ..................................................... 43
4.4.8 Installing Digital Voice Initiating Connections ................................... 43
4.4.9 Installing Ancillary Audio Input Connections ..................................... 43
4.4.10 Setting Adjustable Audio BGM Sources .......................................... 45
4.4.11 Installing Alarm, System Trouble, and AC Trouble Output
Connections ...................................................................................... 45
4.5 Wiring the System .......................................................................................... 46
4.5.1 Wiring Guidelines ................................................................................ 46
4.5.2 Field Wiring Connections .................................................................... 47
4.5.3 Preparing a System Wiring Diagram ................................................... 47
4.5.4 Visual Notification Appliance Output Wiring ..................................... 47
4.5.5 Speaker Notification Appliance Output Wiring ................................... 48
4.5.6 Wiring Diagrams for Audio/Visual Notification Appliances .............. 48
4.5.7 Wiring the Alarm Output Contact ........................................................ 49
4.5.8 Wiring the System Trouble Connections ............................................. 50
4.6 Performing System Checkout ......................................................................... 50
4.6.1 System Control Settings ....................................................................... 50
4.6.2 Checkout Procedure ............................................................................. 51
4.7 Ground Fault Detection .................................................................................. 53
4.8 Battery Care and Backup Battery Calculations .............................................. 53
4.8.1 Caring for Sealed Lead Acid Batteries................................................. 53
4.8.2 Storing Batteries................................................................................... 54
4.8.3 Calculating Backup Battery Requirements .......................................... 54
4.9 Installing AC Power and Batteries ................................................................. 55
4.9.1 Installing AC Power ............................................................................. 55
4.9.2 Installing Batteries ............................................................................... 56
5. Operation 58
5.1 Introduction .................................................................................................... 58
5.2 User Interface ................................................................................................. 58
5.3 Supervision ..................................................................................................... 58
5.3.1 Visual Notification Appliance Output Circuit Supervision ................. 59
5.3.2 Audio Notification Appliance Output Circuit Supervision .................. 59
5.3.3 Amplifier Supervision .......................................................................... 59
5.3.4 Ground Fault Supervision .................................................................... 59
5.4 Actions that Initiate Audio Alarms ................................................................. 59
6. Operating Procedures 60
6.1 Making Live Announcements ........................................................................ 60
6.2 Recording Digital Voice Messages ................................................................ 60
6.3 Recording Messages on the Digital Voice Section......................................... 61
6.4 Verifying Messages ........................................................................................ 62
7. Periodic Testing and Maintenance 63
7.1 Introduction .................................................................................................... 63
7.2 Periodic Testing .............................................................................................. 63
7.2.1 Test Frequency ..................................................................................... 63
7.2.2 Equipment ............................................................................................ 63
7.3 Faulty Equipment ........................................................................................... 63

SP40S Multi-Function Communication System 6

 7.4 Qualified Personnel ........................................................................................ 63
8. Troubleshooting 64
8.1 Introduction .................................................................................................... 64
8.2 General ........................................................................................................... 64
8.2.1 Procedure A ......................................................................................... 68
8.2.2 Procedure B.......................................................................................... 68
8.2.3 Procedure C.......................................................................................... 68
8.2.4 Procedure D ......................................................................................... 69
8.2.5 Procedure E .......................................................................................... 69
8.2.6 Procedure F .......................................................................................... 70
8.2.7 Procedure G ......................................................................................... 70
8.2.8 Procedure H ......................................................................................... 70
8.2.9 Procedure I ........................................................................................... 71
8.2.10 Procedure J........................................................................................ 71
8.2.11 Procedure K ...................................................................................... 71
8.2.12 Procedure L....................................................................................... 72
8.2.13 Procedure M...................................................................................... 72
8.2.14 Procedure N ...................................................................................... 72
8.2.15 Procedure O ...................................................................................... 73
8.2.16 Procedure P ....................................................................................... 73
8.2.17 Procedure Q ...................................................................................... 73
8.2.18 Procedure R ...................................................................................... 74
8.2.19 Procedure S ....................................................................................... 74
8.2.20 Procedure T ....................................................................................... 74
9. Technical Data 75
9.1 Mechanical ..................................................................................................... 75
9.2 Environmental ................................................................................................ 75
9.3 Electrical ......................................................................................................... 75
9.3.1 Input ..................................................................................................... 75
9.3.2 Battery Current Calculations ................................................................ 75
9.3.3 Activation ............................................................................................. 75
9.3.4 Outputs ................................................................................................. 76
9.4 Wiring Connections ........................................................................................ 77
9.4.1 End of Line Resistor (EOLR) .............................................................. 77
10. Warranty 78
11. Battery Backup Calculation Worksheet 79
12. Compatible Signaling Appliances 80

SP40S Multi-Function Communication System 7

SP40S Multi-Function Communication System 8
 List of Figures

Figure 1 Basic Capabilities of the SP40S Panel 21

Figure 2 Layout of SP40S Panel 22
Figure 3 SP40S User Interface 23
Figure 4 SP40 Terminal Blocks 25
Figure 5 SP40S Jumpers 26
Figure 6 SP40S Switches 27
Figure 7 Diagnostic LEDs/Fuses 28
Figure 8 SP40S Potentiometers 29
Figure 9 Grounding Screws and Grounding Standoff Locations 30
Figure 10 Location of Field Wiring Connections 35
Figure 11 SP40S Panel Mounting and Grounding/Conduit Locations 39
Figure 12 Removable Terminal Block 40
Figure 13 Strobe Connections 41
Figure 14 Audio Output Connections 42
Figure 15 Digital Voice initiating Connections 43
Figure 16 Ancillary Audio Input Connections 44
Figure 17 Wiring Diagram for Visual Only Notification Appliances 48
Figure 18 Wiring Diagram for Combination Audio/Visual Notification Appliances 48
Figure 19 Wiring Diagram for Audio Only Notification Appliance Output 49
Figure 20 Alarm Connections 49
Figure 21 System Trouble Connections (Trouble Status Relay Contact) 50
Figure 22 VAC Input Connection 56
Figure 23 Battery Wire Connections 57
Figure 24 Battery Alignment and Jumper Connection 57
Figure 25 SP40S User Interface 62
Figure 26 Trouble LED and Fuse Locations 67

SP40S Multi-Function Communication System 9

SP40S Multi-Function Communication System 10
 List of Tables

Table 1 SP40S Standard Features 19

Table 2 SP40S User Interface Pushbuttons/Indicators 23
SP40S(E)-D User interface Pushbuttons/Indicators 24
Table 4 Terminal Block Connection Definitions 36
Table 5 Digital Voice Message Tests 52
Table 6 Audio Alarm Conditions and Results 59
Table 7 Trouble Procedure Cross Reference 66

SP40S Multi-Function Communication System 11

SP40S Multi-Function Communication System 12
 Forward

1. Forward
1.1 Intended use
This manual is designed to serve the installers and operators of the SP40S Multi-Function
Facility Communication System. All operating instructions, product illustrations,
troubleshooting/error messages, and other relevant information are contained in this
manual. It is the user’s responsibility to ensure that all instructions in this manual are
applied strictly.

1.2 Design Change Disclaimer

Due to design changes and product improvements, information in this manual is subject
to change without notice. Cooper Notification reserves the right to change product
design, including illustrations and diagrams, at any time without notice to anyone, which
may subsequently affect the contents of this manual.
Cooper Notification assumes no responsibility for any errors that may appear in this
manual. Cooper Notification will make every reasonable effort to ensure that this manual
is up to date and corresponds with the shipped Cooper Notification SP40S Multi-
Function Facility Communication System.

1.3 User Operation Assistance

Should you experience any difficulty in installing or operating your SP40S Multi-
Function Facility Communication System, please contact your Cooper Notification
representative. The Troubleshooting chapter in this manual (Chapter 8) includes a list of
common system problems, possible causes, and corrective operator actions. The
information given here is general. Feel free to contact the Technical Support department
of Cooper Notification at 1-800-631-2148. Hours are
8:00 a.m. - 7:00 p.m. (Eastern Time), Monday through Thursday and 8:00 a.m. –
5:00 p.m. (Eastern Time) on Friday.

1.4 Product Model Descriptions

SP40S – 120V, option to annunciate CO alarm (code 4)SP40SE – 240V, option to
annunciate CO alarm (code 4)
SP40S-D – SP40S panel with expanded capability to meet UFC requirements – 10
minute NAC circuit timeout.
SP40SE-D – SP40SE panel with expanded capability to meet UFC requirements – 10
minute NAC circuit timeout.

1.5 Typographical Notation Conventions

Thank you for using our products. Use this product according to this instruction manual.
Please keep this instruction manual for future reference.
Any material extrapolated from this document or from Cooper Notification
manuals or other documents describing the product for use in promotional or
advertising claims, or for any other use, including description of the product's

SP40S Multi-Function Communication System 13

 Forward

application, operation, installation, and testing is used at the sole risk of the user
and Cooper Notification will not have any liability for such use.
Certain information contained in this manual has been extracted from the NFPA 72
Manual and the Life Safety Code 101™ Manual.

WARNING: INDICATES A POTENTIALLY HAZARDOUS SITUATION THAT, IF

NOT AVOIDED, COULD RESULT IN SERIOUS PERSONAL INJURY OR DEATH
TO YOU OR OTHERS.

CAUTION: Indicates a situation which the equipment could be damaged or a situation in

which not following instructions correctly could result in the equipment not working
properly.

SP40S Multi-Function Communication System 14

 Safety Precautions

2. Safety Precautions
2.1 Read This Manual
1. Cooper Notification recommends that, before performing any actions to specify,
apply, install, maintain, and operationally test the SP40S Multi-Function Facility
Communication System, personnel properly qualified in the application and use of
life safety equipment read this manual carefully.
2. Keep this manual with the SP40S Multi-Function Facility Communication System
for reference during the life of the product. Make this manual available to all
qualified personnel who operate, test, maintain, or service the SP40S Multi-Function
Facility Communication System. It is strongly recommend that such personnel read
and understand the entire manual.

2.2 Operational Safety

WARNING: IF SAFETY PRECAUTIONS, INSTALLATION, AND TESTING

INSTRUCTIONS ARE NOT PERFORMED PROPERLY, THE SP40S MULTI-
FUNCTION FACILITY COMMUNICATION SYSTEMS MAY NOT OPERATE IN
AN EMERGENCY SITUATION, WHICH COULD RESULT IN SERIOUS INJURY
OR DEATH TO YOU AND/OR OTHERS.

WARNING: IF THE PROTECTIVE SIGNALING SYSTEM SOUNDS AND/OR

FLASHES, IT IS A WARNING THAT A POSSIBLE SERIOUS SITUATION
REQUIRES IMMEDIATE ATTENTION.

CAUTION: A SP40S Multi-Function Facility Communication System printed circuit

board is sensitive to static electricity and has delicate components mounted on it. (a)
Before handling the board or any component on it, discharge any static electricity from
your body by touching a grounded object, such as a metal screw, which is connected to
earth ground. (b) Handle the board by its edges and be careful not to twist or flex it.
Install the SP40S Multi-Function Facility Communication System in a static-free area.
(c) Attach grounded wrist straps properly before touching any static sensitive areas. (d)
After handling a SP40S Multi-Function Facility Communication System printed circuit
board, test the panel as described in section 4.6 to verify that it is functioning properly.

NOTE: In areas prone to lighting strikes, using a surge protection device is recommended.
NOTE: This SP40S Multi-Function Facility Communication System will not work without
power. The SP40S Multi-Function Facility Communication System is powered by 120 or 240
VAC, depending on model. 24VDC re-chargeable batteries provide backup power, should
be purchased separately. If both sources of power are cut off for any reason, the SP40S
Multi-Function Facility Communication System will not operate.
1. DO NOT assume any installation, operation, and testing details not shown in this
manual.

SP40S Multi-Function Communication System 15

 Safety Precautions

CAUTION: DO NOT operate the SP40S Multi-Function Facility Communication System

without the dead front panel being properly in place.

2.2.1 Expected Equipment Lifecycle

Notification equipment cannot last forever. Even though the SP40S Multi-Function Facility
Communication System is expected to last up to ten years, any of its parts or components
could fail before then.

2.2.2 Periodic Testing

1. Cooper Notification recommends testing of the entire protective signaling system,
including the SP40S Multi-Function Facility Communication System, all notification
equipment, as well as all messages and their output channel, and priority assignment,
at least twice each year, or more often as required by local, state and federal codes,
regulations and laws, by qualified personnel.
2. If the notification equipment is not working properly, immediately contact the
installer and have all/any problems corrected immediately.
3. Replace any malfunctioning components immediately; do not attempt to repair
malfunctioning components. Return malfunctioning components for factory
repair or replacement. In the event you cannot contact the installer, contact the
manufacturer.

WARNING: FOR PROPER OPERATION IN LIFE SAFETY APPLICATIONS,

PERFORM THE FOLLOWING: (A) CONNECT THE SP40S MULTI-FUNCTION
FACILITY COMMUNICATION SYSTEM TO A LISTED COMPATIBLE AND
PROPERLY OPERATING CONTROL PANEL, WHICH CONTROLS ITS
ACTIVATION. (B) ENSURE THAT ALL EQUIPMENT IS PROPERLY
INTERCONNECTED AND OPERATING. (C) MAKE SURE THE INSTALLER
CHECKS THE COMPATIBILITY OF ALL EQUIPMENT PRIOR TO
INSTALLATION; OTHERWISE, THE SP40S MULTI-FUNCTION FACILITY
COMMUNICATION SYSTEM AND/OR THE CONTROL PANEL MAY BE
DAMAGED AND/OR FAIL TO OPERATE IN AN EMERGENCY SITUATION.

WARNING: CERTAIN HARDWARE FUNCTIONS ON THE SP40S MULTI-

FUNCTION FACILITY COMMUNICATION SYSTEM ARE NOT SUPERVISED. IF
ANY SUCH HARDWARE FUNCTIONS FAIL, THE SP40S MULTI-FUNCTION
FACILITY COMMUNICATION SYSTEM MAY NOT PROVIDE THE INTENDED
WARNING AND/OR NOT INDICATE A TROUBLE CONDITION.

2.3 Compliance with Applicable Codes, Regulations, Laws, Standards, and

Guidelines
Comply with all of the latest applicable codes, regulations, laws, standards, and guidelines.

SP40S Multi-Function Communications System 16

 Safety Precautions

WARNING: ENSURE THAT FOR EMERGENCY, LIFE SAFETY APPLICATIONS

USING THE SP40S MULTI-FUNCTION FACILITY COMMUNICATION SYSTEM,
INSTALLATION, TESTING AND MAINTENANCE ALWAYS BE PERFORMED BY
QUALIFIED PERSONNEL IN ACCORDANCE WITH ALL THE LATEST
NATIONAL FIRE PROTECTION ASSOCIATION (NFPA), UNDERWRITER’S
LABORATORY (UL), NATIONAL ELECTRIC CODE (NEC), OCCUPATIONAL
SAFETY AND HEALTH ADMINISTRATION (OSHA), STATE, COUNTY, LOCAL,
PROVINCE, DISTRICT, FEDERAL, AND OTHER APPLICABLE BUILDING AND
FIRE STANDARDS, GUIDELINES, REGULATIONS, LAWS, AND CODES
INCLUDING, BUT NOT LIMITED TO, ALL APPENDICES AND AMENDMENTS
AND REQUIREMENTS OF THE LOCAL AUTHORITY HAVING JURISDICTION
(AHJ).

WARNING: ALL ELECTRICAL INSTALLATIONS SHALL BE IN ACCORDANCE

WITH THE APPROPRIATE NATIONAL ELECTRICAL CODE – CAN/ULC S524,
CANADIAN ELECTRICAL CODE, PART 1, NATIONAL BUILDING CODE OF
CANADA. FINAL ACCEPTANCE IS SUBJECT TO AUTHORITIES HAVING
JURISDICTION

It is recommended that the local Authority Having Jurisdiction (AHJ) inspect and approve
the proposed placement of all the notification appliances.

2.4 Insurance Recommendation

The SP40S Multi-Function Facility Communication System is not a substitute for insurance.
Make sure that you have adequate levels of life and property insurance.

2.5 Audio Output Considerations

CAUTION: The output of the audio system may not be heard in all cases. Sound can be
blocked or reduced by walls, doors, carpeting, wall coverings, furniture, insulation, bed
coverings, and other obstacles that may temporarily or permanently impede the output
of the audio system. Sound is also reduced by distance and masked by background noise.
The output of the audio system may not be sufficient to alert all occupants, especially
those who are asleep, those who are hearing-impaired, those who are wearing devices
that plug or cover the ears, and those who have recently used drugs or alcohol.
The output of the audio system may not be heard by an alert person if the output device
is placed in an area which is isolated by a closed door, or is located on a different floor
from the person in a hazardous situation or is placed too far away to be heard over
ambient noise such as, but not limited to, running water, traffic, air conditioners,
machinery or musical appliances.
If live microphone announcements, audible tones and/or voice messages cannot be
readily heard and understood clearly within the protected areas as intended, increase
the number and/or sound output intensity of speakers within those areas so that they are
heard and understood clearly when activated.

WARNING: AUDIBLE SIGNALS MAY MASK MEDICAL EQUIPMENT

MONITORING ALARMS. WHERE MEDICAL EQUIPMENT MONITORING
ALARMS ARE IN USE, DO NOT USE AUDIBLE SIGNALS; PROVIDE VISUAL
NOTIFICATION APPLIANCES IN HIGHLY VISIBLE LOCATIONS.

SP40S Multi-Function Communications System 17

 Safety Precautions

2.6 RF Interference
The SP40S Multi-Function Facility Communication System has been tested and found to
comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in
which case the user is required to correct the interference at their own expense.

2.7 General
Each manufacturer's panel and notification appliances operate differently and have different
features. Before specifying, installing, operating, testing, maintaining, or servicing a
system, carefully read the installation, operation, and testing manual for each piece of
equipment and applicable codes.
Additional copies of this manual may be obtained from:
Cooper Notification
273 Branchport Ave.
Long Branch, N.J. 07740
Tel: (800) 631-2148
Fax: (732) 222- 2588
E-mail: [email protected]

SP40S Multi-Function Communications System 18

 Overview

3. Overview
The SP40S Multi-Function Facility Communication System is capable of supplying the
following:
• 40 Watts of audio power
• 2 Amps of strobe power
• There is an additional 0.5 Amps of auxiliary power at 28 Volts that can be used to power
other Safepath Products.
The SP40S Multi-Function Facility Communication System is used for Alarm and Non
Alarm Announcements.
The SP40S-D and SP40SE-D models do not have the option of carbon monoxide (CO)
annunciation. If you have either of these models, ignore any reference to that option.

3.1 Compatibility with Existing Safepath Products

The SP40S Multi-Function Facility Communication System is fully compatible with the
SP40S, all current Audio Splitters (SP4Z-A/B and SP4-APS), the Safepath Remote
Microphone (SPRM), the Safepath Volume Control (SP-SVC), the Telephone Zone
Controller (SP4-TZC), and the Safepath Remote Microphone Expander (SP4-RMX). A
maximum of two SP4-RMX units can be connected to the SP40s.

3.2 Standard Features

Table 1 SP40S Standard Features
Feature Description
• 24VDC @ 2 Amps Maximum.
• Requires separate NAC Circuit (8 to 33VDC) input or can be
programmed to operate when Digital Voice messages are played.
• Microphone (MIC) is active.
• Auxiliary (AUX) input is active and/or Digital Voice message are
played. (Each message can be programmed individually to activate
the strobe circuitry.)
One strobe NAC output section • Return allows pass-through for Cooper Notification synchronized
strobes, remote SP40S panels, additional strobe appliances, or
EOLR.
• Synchronized output when using Cooper Notification’s
synchronized strobe products.
• Supervised with 10K Ohm end-of-line resistor (EOLR).
• Trouble LEDs for Open and Short conditions.
• Power limited to minimize overload condition.
• Selection of 25V,70V or 100V RMS speaker output.
• Supervised with 10K Ohm EOLR.
40-Watt Audio Amplifier section • Trouble LEDs for Open and Short Conditions
• Power limited to avoid overload condition.
• 25V setting: Class 2
• 70V setting: Class 3

SP40S Multi-Function Communications System 19

 Overview

• Capable of playback and record (via 1/8” audio jack).

• Digital Voice Message Chip contains the recording program and
memory for eight message sections.
• Memory in eight sections with corresponding inputs.
o A total of four minutes of messages.
o Each message is 30 seconds in duration.
o Messages can be combined for longer durations.
• Activated by one of eight contact closure inputs (IN1 – IN8) or
Digital Voice Section manual activation on user interface.
• Each CC input (contact closure) can be supervised for an OPEN.
• Pre-alert tones can be chosen for each message (code 3, code 4,
continuous, or no pre-tone). Code 4 uses a low frequency 520Hz
pre-alert tone in sleeping area applications for CO annunciation.
• Messages can be selected to have a post-tone that matches the
pre-tone.
• Capable of selecting the strobe NAC output for each input.

Feature Description

• Three Priority ordered audio inputs

Hand-held, push-to-talk (PTT) microphone, and Priority 1. For live,
emergency voice announcements and instructions. The microphone
overrides (mutes) any voice message or tones in progress.
• Auxiliary Input (AUX IN, CC/NAC), Priority 2.
o CC or NAC initiates AUX IN audio
o CC is supervised. NAC is not supervised.
o For use with SAFEPATH – Remote Microphone Expander
Alarm Audio Processing Section (SP4-RMX) or SAFEPATH – Remote Microphone (SPRM)
• Digital Voice Section inputs (IN1, IN2, IN3, IN4, IN5, IN6, IN7,
IN8).
o IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8 have priorities 3, 4, 5,
6, 7, 8, 9, and 10 respectively.
o IN1 – IN8 are initiated via Contact Closure.
o IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8 are supervised for an
OPEN.
o Messages can also be initiated via user interface.

• Night Ring (NR), Priority 6.

o Contact closure activated.
o Non-alarm.
o Does not operate if on Battery.
Non-Alarm Audio Processing • Telephone Page (TEL), Priority 7.
Section o Accepts a Telephone Page Port Input.
o Will not operate if the panel is on Battery.
• Background Music (BGM), Priority 8.
o Line Level Input.
o Will mute when any other input is used.
o Will not operate if the panel is on Battery.

Monitors inputs and outputs for 40K Ohms minimum in relation to

Ground Fault Detection Section
ground.

A Dual-Tone Tone Generator with

two field selectable sounds (Code Provides Code 3 tone or Slow Whoop (user selectable) in the instance
3 Tone, Slow Whoop) that sound of a Digital Voice failure or system timeout.
when there is a Digital Voice

SP40S Multi-Function Communications System 20

 Overview

Section Failure in alarm condition.

Audio NAC circuit wiring -- open and short conditions during standby
AND active (Alarm and BGM) Ground Fault detection
Strobe NAC circuit wiring -- open and short conditions
Full supervision with on-board PTT Microphone -- not installed or damaged
diagnostics and trouble reporting Amplifier -- operation
circuits for: Digital Voice Section
Input voltage/low battery
Tone generator operation

Feature Description

Form C contact normally energized. Contacts transfer during a trouble,

Form C relay trouble contacts for
an alarm trouble, or an AC trouble: 2.0 amps at 24VDC max, resistive
external notification.
load. Non-Supervised.
To indicate trouble, with a trouble silence switch to silence it. If the
Built-in Sounder trouble is not corrected in 20 hours, the sounder reactivates. (Trouble
Silence Switch does not change the state of the Form C Trouble relay.)
Remote reporting via output
AC trouble can be configured for report separately or as a system
contacts for system trouble, alarm
trouble.
activation, and AC trouble.

Figure 1 Basic Capabilities of the SP40S Panel

3.3 Enclosure and Configuration

For technical specifications, see Chapter 9

3.4 Nominal Electrical Data

For technical specifications, see Chapter 9.

SP40S Multi-Function Communications System 21

 Overview

MOTHERBOARD

AC Wiring
(NON-POWER* Wiring to Battery
(NON-POWER
LIMITED) LIMITED)

* MUST BE ROUTED OUT

BOTTOM LEFT OF ENCLOSURE USER INTERFACE

Figure 2 Layout of SP40S Panel

3.5 User Interface

The User Interface of the SP40S Multi-Function Facility Communication System displays
the basic status of the unit as well as allowing for a limited amount of user controls. Table
2identifies the pushbuttons and indicators. Table 3 describes the different operation for
Messages 1-6 on the SP40S-D and SP40SE-D.

Message 1
Message 2
Message 3
Message 4
Message 5
Message 6
Message 7
Message 8

SP40S Multi-Function Communications System 22

 Overview

Figure 3 SP40S User Interface

Table 2 SP40S User Interface Pushbuttons/Indicators

Pushbutton or Indicator Description/Function

Message 1 - 8 (there are 8 messages, 1 through 8) Button manually actives Messages 1- 8. Illuminated
steady means contact closure is on a DV input.
Illuminated blinking means DV is activated via button
push.

POWER ON indicator If illuminated, indicates SP40S is powered by primary or

secondary power.

SYSTEM TROUBLE indicator If illuminated, indicates the SP40S has a trouble.

AC TROUBLE indicator If illuminated, indicates primary power is low or has

failed and SP40S is running on secondary power.

ALARM ACTIVE indicator Indicates PTT MIC (push to talk microphone), AUX
(auxiliary), or DV (digital voice) has been initiated.

STROBE ACTIVE indicator Indicates the strobe circuit has been initiated.

TROUBLE SILENCE button Temporarily silences the audible trouble indicator.

RECORD button and indicator For message recording process, see section 6.3.

3.5.1 Basic Operation of User Interface

When a Message button is pressed, the user interface microcontroller processes the signal
and outputs it to the Digital Voice microcontroller which plays the corresponding message.
The user interface illuminates the corresponding message LED when a button is pressed or a
message activation contact closure is received. The LED blinks if the activation was a button
press and the LED remains ON constantly when a contact closure is present. If a button is
pressed, the message LED remains blinking and the message remains active until the button
is pressed again.

3.5.2 Overview
This section describes the behavior differences of digital voice messages between SP40S
firmware and SP40S-D firmware. The SP40S-D firmware changes are limited to the user
interface section of the SP40S panel (refer to Figure 1). All other behaviors of the SP40S,
such as strobe activation, message prioritization, and AUX input functionality have not
changed.
3.5.2.1 Operation of Digital Voice Messages with SP40S firmware
Digital voice (DV) messages on the SP40S are activated locally via the front panel interface
pushbuttons (PB) or remotely using contact closures (CC) with the SP40S firmware. An
activated DV message will remain active indefinitely until you clear the source of activation.
Activation of a particular DV message appears locally at the front panel interface by LEDs

SP40S Multi-Function Communications System 23

 Overview

located on each DV message PB. For the SP40S firmware, a flashing LED indicates that the
PB activated a message, and a solid LED indicates that a CC activated a message.
3.5.2.2 Operation of the Digital Voice Messages with the SP40S-D firmware

Each PB and CC for DV messages 1 through 6 are individual inputs each having their own
10-minute timer. If one of the inputs goes active its associated timer starts, the associated
message starts playing, and if the input does not restore, the input’s timer will time out and
the message will stop playing. The input must restore before it can go active again,
triggering the message to play.
Example 1: CC1 goes active, its timer starts and message1 starts playing. If CC1 does not
restore, the timer will expire and the message will stop playing in 10 minutes. Once CC1
times out, CC1 cannot trigger message1 to play again until CC1 restores. You can,
however, press PB1 and message1 will start playing again and will continue for 10 minutes
if PB1 remains active. If PB1’s timer is allowed to time out also, message one cannot be
triggered by anything now since both of its associated inputs are still in “Timeout” mode.
One or both must restore and re-activate for message1 to start playing again.
Example 2: CC1 goes active, its timer starts and message1 starts playing. 8 minutes into
the timer PB1 goes active which start PB1’s timer and message1 continues to play for
another 10 minutes. This makes the total play time 18 minutes in this example if neither
CC1 nor PB1 restores and re-activates. It is possible that lower priority messages may not
be heard at all because of a higher priority message’s inputs being restored and re-activated
while the lower priority input times out.
DV message 7 and 8’s inputs (PB & CC) do not have a timer associated with them and will
continue to play message 7 or 8 until the input restores or a higher priority input goes active.
Example 3: PB7 activates which starts message7 playing. This message will continue
playing as long as PB7 remains active. CC1 goes active, its timer starts, CC1 is a higher
priority message, so message1 is heard instead of message7 now. CC1 remains active
through the 10 minute timer and the timer times out shutting off message1. Message7 starts
playing again at this time because PB7 is still active.
The addition of the timeout functionality in the SP40S-D firmware causes the user interface
on the SP40S to indicate that a particular DV input is in timeout.
Table 3 SP40S(E)-D User interface Pushbuttons/Indicators
LED Indicator Function DV Description
Message LED
STEADY OFF Both the PB and CC input for the DV message are INACTIVE.
STEADY ON The DV message input is ACTIVE as a result of either PB or CC activation.
ONE BLINK The CC input for the DV message is in the TIMEOUT state and the PB input is
INACTIVE. Deactivating the CC input will cause the LED to turn off as both
inputs become INACTIVE.
TWO BLINKS The PB input for the DV message is in the TIMEOUT state and the CC input is
INACTIVE. Deactivating the PB input will cause the LED to turn off as both
inputs become INACTIVE.
THREE BLINKS Both the CC input and the PB input for the DV channel are in the TIMEOUT
state.

SP40S Multi-Function Communications System 24

 Overview

3.5.2.3 Timeout State

Other outputs may be affected when the system is in the timeout state. In the timeout state,
the alarm active relay and LED will deactivate. If strobes are tied to a message, then the
strobe output and LED will also deactivate.

3.6 Additional Drawings

Figure 4 SP40 Terminal Blocks

SP40S Multi-Function Communications System 25

 Overview

J1 Audio JP4 Contact

Output Select Closure Supervision

JP3
2 Wire/4 Wire Mode
(For connection
to Audio Boosters)

JP5 DV J4 AUX IN
Record Select

J6 User
J5 FACP Interface
Display
(for future use)
Interface
Connection

Figure 5 SP40S Jumpers

SP40S Multi-Function Communications System 26

 Overview

SW2 AC Trouble Settings

Booster Connection
Settings

SW3 Strobe
Activation SW4
Tone Types

SW6
NAC/Contact
Closure Select

SW7 DV IN
Supervision
SW5 Pretone/ and Auxiliary
Postone Enable Timeout

SW9 Sync/
Nonsync
Strobe
Settings

Figure 6 SP40S Switches

SP40S Multi-Function Communications System 27

 Overview

D4 MIC
PTT MIC Missing
D1 Audio Circuit or Inoperable
Open
D3 DV
Digital D5 AMP
Amplifier Section D6 SPB
D2 Audio Circuit Voice Section Supervision Open
Trouble
Short

D8 Batteries
Missing or Low

D29
(Red) Audio
Peak/Overload
D44 AUX IN,
CC Open,
RMX or
Remote MIC
Trouble

D47 Interface
Trouble
D55 - DV1 - IN1 OPEN
D62 - DV2 - IN2 OPEN

D58 - DV3 - IN3 OPEN

D65 - DV4 - IN4 OPEN
D67 GF
Ground
D75 - DV5 - IN5 OPEN
Fault
Trouble
D78 - DV7 - IN7 OPEN
D87 - DV8 - IN8 OPEN
D84 - DV6 - IN6 OPEN

D97 Strobe Open

D96 Strobe Circuit
F2 AC Short
Line Fuse D109 (Green)
(250V 10A) AC Power is Present

D93 Battery D100 (Green) F1 Battery Fuse

Charger Trouble Power is Present (125V 8A)
(AC and/or BAT)

Figure 7 Diagnostic LEDs/Fuses

SP40S Multi-Function Communications System 28

 Overview

R40 Telephone
Page Volume
Control

R92 Background
Music Volume
Control
R93 Tone
Control Treble
R73 Digital
Voice Volume
Control R94 Tone
Control Bass
R81 Digital
Voice Tone R100 AUX IN
Volume Control Volume
Control

Figure 8 SP40S Potentiometers

SP40S Multi-Function Communications System 29

 Overview

Figure 9 Grounding Screws and Grounding Standoff Locations

These 8 parts must be installed and securely fastened.

3.7 User Settings

3.7.1 Switch Descriptions

SW2 (AC Trouble Settings, Booster Connection Settings)
PIN FUNCTION ON
10k EOLR supervision On For SPB
1 Ext. AC Loss Sup.
SUP Contacts
170 minute AC Loss Delay
2 AC Loss Delay
(For Off Premise AC Loss Reporting)
Audio Booster AC Trouble Reported
3 Ext AC TRB Mode
To SP40S Separately

SP40S Multi-Function Communications System 30

 Overview

SW3 (Strobe Activation)

PIN FUNCTION ON
1 DV1 Strobe STB on when DV1 active
2 DV2 Strobe STB on when DV2 active
3 DV3 Strobe STB on when DV3 active
4 DV4 Strobe STB on when DV4 active
5 DV5 Strobe STB on when DV5 active
6 DV6 Strobe STB on when DV6 active
7 DV7 Strobe STB on when DV7 active
8 DV8 Strobe STB on when DV8 active
9 MIC Strobe STB on when MIC active
10 AUX Strobe STB on when AUX active

SW4 (Tone Types)

PIN FUNCTION ON
1 Tone Type - DV1 Code 3 (OFF = continuous 1kHz/Code 4 520Hz)
2 Tone Type - DV2 Code 3 (OFF = continuous 1kHz/Code 4 520Hz)
3 Tone Type - DV3 Code 3 (OFF = continuous 1kHz/Code 4 520Hz)
4 Tone Type - DV4 Code 3 (OFF = continuous 1kHz/Code 4 520Hz)
5 Tone Type - DV5 Code 3 (OFF = continuous 1kHz/Code 4 520Hz)
6 Tone Type - DV6 Code 3 (OFF = continuous 1kHz/Code 4 520Hz)
7 Tone Type - DV7 Code 3 (OFF = continuous 1kHz/Code 4 520Hz)
8 Tone Type - DV8 Code 3 (OFF = continuous 1kHz/Code 4 520Hz)
9 Backup tone Code3 (OFF = slow whoop)
10 Pre-tone frequency 520Hz for sleeping areas (OFF = 1kHz)

SW5 (Pre-tone/Post-tone Enable)

PIN FUNCTION ON
1 Pre-tone - DV1 Pre-tone ON for Message 1
2 Pre-tone - DV2 Pre-tone ON for Message 2
3 Pre-tone - DV3 Pre-tone ON for Message 3
4 Pre-tone - DV4 Pre-tone ON for Message 4
5 Pre-tone - DV5 Pre-tone ON for Message 5
6 Pre-tone - DV6 Pre-tone ON for Message 6
7 Pre-tone - DV7 Pre-tone ON for Message 7
8 Pre-tone - DV8 Pre-tone ON for Message 8
9 Post-tone - All Post-tones enabled (Post-tone Matches Pre-tone)
10 Message Repeat ON = Message plays a minimum of 3 times
OFF = Message plays a minimum of 1 time*

*NOTICE TO USERS, INSTALLERS, AUTHORITIES HAVING JURISDICTIONS AND OTHER

INVOLVED PARTIES: In order for this product to comply with the requirements in the Standard for
Control Units and Accessories for Fire Alarm Systems, UL 864, Position 10 of SW5 must be kept in the ON
position. UL 864, 9th Edition, section 34.2.1.1 requires the alert tone/prerecorded message combination shall
be repeated a minimum of 3 times.

SP40S Multi-Function Communications System 31

 Overview

SW6 (Initiation mode select for Aux IN)

SETTING DESCRIPTION
Contact Closure Mode for use with RMX or
CC
SPRM
NAC 8 to 33VDC NAC Input

SW7 (DV IN Supervision and Auxiliary Timeout)

PIN FUNCTION ON
1 DV MES 1 CC Supervision 10k EOLR supervision ON for IN1
2 DV MES 2 CC Supervision 10k EOLR supervision ON for IN2
3 DV MES 3 CC Supervision 10k EOLR supervision ON for IN3
4 DV MES 4 CC Supervision 10k EOLR supervision ON for IN4
5 DV MES 5 CC Supervision 10k EOLR supervision ON for IN5
6 DV MES 6 CC Supervision 10k EOLR supervision ON for IN6
7 DV MES 7 CC Supervision 10k EOLR supervision ON for IN7
8 DV MES 8 CC Supervision 10k EOLR supervision ON for IN8
9 AUX Input Timeout Timeout active
10 unused --

SW9
PIN FUNCTION ON
Standard Sync
1 Sync mode (NAC input)
(OFF = PASS THRU SYNC MODE)
2 Sync mode (Alarm) Standard Sync (OFF = 28 volts)
3 unused --

3.7.2 Jumper Descriptions

Jumper Description Additional
J1 Audio Output Level Select (25/70/100V)
J4 AUX IN Select (1/25/70/100 V)
J5 FACP Interface (for future use)
J6 User Display Interface Connection Trouble occurs if Interface is not connected

JP2 NOT USED NOT USED

JP3 2-Wire / 4-Wire Mode Removed = 4-Wire Mode
JP4 Contact Closure Supervision (AUX SUP) REMOVED = CC input supervision active
JP5 DV Record REMOVED = DV Record can be activated
JP6 NOT USED NOT USED

SP40S Multi-Function Communications System 32

3.8 LED Descriptions
Head Description Additional
D1 Audio Output Open ON = Audio Output is open or missing EOLR
D2 Audio Output Short ON = Audio Output is shorted
D3 DV, Digital Voice Section ON = DV Audio is low or DV is damaged
ON = MIC missing or inoperable;
D4 MIC, PTT MIC Missing or inoperable
Blinking = MIC preamp trouble
ON = Amplifier trouble or audio current limiting;
D5 AMP, Amplifier Section Trouble
Blinking = AUX preamp trouble
D6 External AC Wiring trouble ON = SPB SUP missing EOLR
D8 Battery Trouble ON = BATT missing or low
D29 Audio Peak/Overload ON = Audio level is too high
D44 AUX IN Trouble ON = CC Open, RMX, or Remote MIC Trouble
D47 User Interface trouble User Interface is improperly connected
D55 DV1 – IN1 OPEN ON = IN1 open or missing EOLR
D58 DV3 – IN3 OPEN ON = IN3 open or missing EOLR
D62 DV2 – IN2 OPEN ON = IN2 open or missing EOLR
D65 DV4 – IN4 OPEN ON = IN4 open or missing EOLR
D67 GF, Ground Fault Trouble
D75 DV5 – IN5 OPEN ON = IN5 open or missing EOLR
D78 DV7 – IN7 OPEN ON = IN7 open or missing EOLR
D84 DV6 – IN6 OPEN ON = IN6 open or missing EOLR
D87 DV8 – IN8 OPEN ON = IN8 open or missing EOLR
D93 Battery Charger Trouble ON = Battery charger circuit in trouble
D96 Strobe Short ON = Short on strobe out
D97 Strobe Open ON = Strobe out open or missing EOLR
D100 (Green) Power ON = AC and or BAT Power is present
D109 (Green) AC Power ON = AC Power is present

SP40S Multi-Function Communications System 33

 Installation

4. Installation
4.1 Introduction
Remember, the lives of people depend upon the safe and proper installation of the voice
evacuation system and the SP40S Multi-Function Facility Communication System. Please
read, understand, and follow the specific installation instructions set forth in this chapter
carefully to avoid damage to the panel and equipment connected to it. Ensure that only
qualified personnel in accordance with the procedures in this manual conduct the
installation.

WARNING: POSSIBLE FIRE HAZARD - REMOVAL OF ALL SHIPPING

MATERIAL IS REQUIRED PRIOR TO WIRING OF YOUR SAFEPATH PANEL.

SHUT OFF ALL POWER BEFORE STARTING THE INSTALLATION.

ELECTRICAL SHOCK CAN CAUSE DEATH OR SERIOUS INJURY.

WARNING: DO NOT CONNECT AC POWER OR BATTERY BACKUP POWER

UNTIL SYSTEM WIRING HAS BEEN CONNECTED, MODULES HAVE BEEN
INSTALLED, AND FIELD WIRING HAS BEEN INSPECTED.

CAUTION: The SP40S printed circuit board is sensitive to static electricity and has
delicate components mounted on it. Before handling the board or any component on it,
discharge any static electricity from your body by touching a grounded object such as a
metal screw, which is connected to earth ground. Install the panel in a static-free area;
properly attach grounded wrist straps before touching any static-sensitive areas.

• If you or the installer have any questions about the installation, consult with the
authorities having jurisdiction (AHJ), prior to installation.

4.2 Fire Alarm Control Panel Wiring Applications

The SP40S Digital Voice Section inputs require Contact Closures to initiate. The Fire
Alarm Control Panel (FACP) supplies these dry Contact Closures.
NOTE: Do not connect a NAC or DC voltage directly to the Digital Voice Inputs. A relay
is required.

The SP40S strobe input requires 8-33VDC to initiate. The FACP NAC Circuit of 12VDC or
24VDC initiates this circuit.

TROUBLE Form C relay terminals and an internal sounder are available for monitoring the
condition of the SP40S Multi-Function Facility Communication System.

SP40S Multi-Function Communications System 34

 Installation

4.3 General Installation Instructions

For a view of the location of wiring connections used in the installation of the SP40S Multi-
Function Facility Communication System, refer to Figure 10. Table 4 explains the functions
of the different wiring connections.

Section 2
Section 1 System Trouble Connections
Alarm Connections Section 3
AC Trouble
Connections

Section 4
Audio Output
Connections

Section 5
Night Ring, Telephone
Page, Background
Music Connections

Section 6
Auxilary Input
and 24VDC
Output
Connections

Sections 7 and 8
Internal Digital Voice
Connections

Section 9 Section 11
Section 10 Strobe Connections
Primary Power Secondary Power
(120VAC) Connections (Battery) Connections

Figure 10 Location of Field Wiring Connections

SP40S Multi-Function Communications System 35

 Installation

Table 4 Terminal Block Connection Definitions

Terminal Definitions
Symbol Alarm Connections
Block
Alarm Connections

Alarm Form C relay changes state in Audio Alarm Conditions. These

conditions are: Push-to-talk Button on MIC depressed. AUX initiated via
ALM Alarm connections CC or NAC, and IN1- IN8 inputs present. Contacts are rated at 24VDC,
TB1 2A. Resistive load.
Terminal
Block 1 NO Normally open Alarm Relay contact open to Common (COM) in non-alarm condition.
Section 1

NC Normally closed Alarm Relay contact closed to Common (COM) in non-alarm condition.

COM Common Alarm Relay Common (COM).

System Trouble Connections

Trouble Form C relay changes state in Trouble Conditions. Contacts are
TRB System Trouble connections
rated at 24VDC, 2A. Resistive load.
TB2
Terminal Trouble Relay contact open to Common (COM) when a system trouble is
NO Normally open
Block 2 NOT present.
Section 2
Trouble Relay contact closed to Common (COM) when a system trouble
NC Normally closed
is NOT present.

COM Common Trouble Relay Common (COM).

AC Trouble Connections
AC Trouble Form C relay changes state when primary power is missing or
AC TRB AC Trouble connections
low. Contacts are rated at 24VDC, 2A. Resistive load.
TB3
Terminal AC Trouble Relay contact open to common (COM) when primary power is
NO Normally open
Block 3 sufficient.
Section 3
AC Trouble Relay contact closed to common (COM) when primary power
NC Normally closed
is sufficient.

COM Common AC Trouble common (COM).

Terminal
Symbol Alarm Connections Definitions
Block
Audio Output Connections
Audio Output for 25V or 70V speakers. Supervised using UL Listed 10K
AUD Ohm, ½ W EOLR. Power Limited.
Audio Output
OUT
TB4 25V setting = Class 2; 70V setting = Class 3
Terminal
24V 24 VDC, 0.5A Continuous Output Connection, Power Limited auxiliary
Block 4 24 VDC, 0.5A Output
OUT power source. NOTE: Two 24V outputs combine for 0.5A.
Section 4
Contact Closure indicates a primary power loss on the audio booster.
SPB SAFEBAPTH4 Booster Input is supervised using 10k Ohm EOLR. Used only when AC loss is
SUP Supervision reported separately from system trouble. Active only when SW2
Position 3 is ON.
Night Ringer, Telephone Page, Background Connections
Contact Closure Input initiates chime sound for Night Ring. Non-
NR Night Ring supervised. Night Ring does not operate without VAC input and the Panel
TB5 is operating on Battery.
Terminal
Telephone Page Input from a telephone Page Port. Non-Supervised.
Block 5
TEL Telephone Page Input Telephone Page does not operate without VAC input and the Panel is
Section 5
operating on Battery.
BGM Background Music Input Line Level, 600 Ohm Background Music Input. Automatically mutes when
any other input is in use. Non-Supervised. Background Music input does
not operate without VAC input and the panel is operating on Battery

SP40S Multi-Function Communications System 36

 Installation

Auxiliary Input and 24VDC Output Connections (For Connection To SPRM or SP4-RMX)
AUX Auxiliary Input Audio Line Level Audio Input, Remote MIC, or SP4-RMX Priority 2.
TB6
Terminal Contact closure or NAC will initiate AUX IN Audio. CC is supervised.
CC/NAC Contact Closure/NAC
Block 6 Connects to RMX or Remote MIC (CC Mode).
Section 6,
Regulated, 24 VDC, 0.5A Continuous Output Connection, Power Limited
24V Out 24VDC, 0.5A output auxiliary power source. NOTE: Two 24V outputs combine for 0.5A.
Connects to RMX or Remote MIC.

Terminal
Symbol Alarm Connections Definitions
Block
Internal Digital Voice Module Input Connections
Digital Voice Initiating connection for message #1 (contact closure).
IN 1 Input 1
Priority 3.
TB7
Digital Voice Initiating connection for message #2 (contact closure).
Terminal IN 2 Input 2
Priority 4.
Block 7
Section 7 Digital Voice Initiating connection for message #3 (contact closure).
IN 3 Input 3
Priority 5.
Digital Voice Initiating connection for message #4 (contact closure).
IN 4 Input 4
Priority 6.

Internal Digital Voice Module Input Connections

Digital Voice Initiating connection for message #5 (contact closure).

IN 5 Input 5
Priority 7.
TB8
Terminal Digital Voice Initiating connection for message #6 (contact closure).
IN 6 Input 6
Block 8 Priority 8.
Section 8 Digital Voice Initiating connection for message #7 (contact closure).
IN 7 Input 7
Priority 9.
Digital Voice Initiating connection for message #8 (contact closure).
IN 8 Input 8
Priority 10.
TB9
Terminal
Primary Power (VAC) Connections
Block 9
Section 9
AC Input Voltage. Make sure Line (L), Neutral (N), and Ground (G) are
AC Primary Power (AC) connected. Non-power limited. Make sure power cord is run properly (see
wiring diagram Figure 4-13 in Section 4.9.1).

TB10 Secondary Power (Battery) Connections

Terminal
Block 10 24VDC, up to 33 Ah Battery input connection. The enclosure can
Section BAT Secondary Power (Battery) accommodate up to 12 Ah. Batteries greater than 12 Amp-Hours (Ah) are
10 required to be installed in a UL listed battery box. Non-power limited.

Strobe Connections. See Appendix E for strobe compatibility list.

TB12 STB 8-33 VDC, Regulated, 2A Maximum Strobe NAC Output Supervised with
Strobe Output
Terminal OUT UL Listed 10k Ohm, ½ W EOLR. (Power limited).
Block 12
Section Strobe Input Return for connecting additional strobe circuits, or UL Listed
RET Return
11 10k Ohm, ½ W EOLR.

STB IN Strobe Input 8-33 VDC, Strobe NAC Input. Triggers strobe in Alarm condition.

NOTE: All Outputs (Strobe Output, Audio Output, and 24VDC Auxiliary Power Source) are
power limited circuits.

SP40S Multi-Function Communications System 37

 Installation

4.4 Preparing the System Wiring Diagram

• Keep a copy of the system-wiring diagram with the SP40S manual as a permanent
record of the system wiring.

4.4.1 Unpacking and Taking Inventory

Carefully unpack the panel and make sure each item described on the packing slip is present
and undamaged.
1. Check the exterior of the shipping container(s) for any exterior damage, then the
interior of the container(s).
2. Notify both the carrier and Cooper Notification immediately on the straight bill of
lading (supplied by the carrier) if any damage is found both verbally and in writing;
you may also request an inspection by the carrier. Such requests must usually be
made within a specified time period from date of shipment. Cooper Notification is
not responsible for damage to equipment occurring during shipping, and only
furnishes replacement parts against a written purchase order. It is the customer’s
responsibility to file a claim with the carrier.
3. Follow any instructions Cooper Notification and/or the carrier may supply about
possible damage.
4. If no damage is found, compare the contents of the Inventory List against the
contents of the shipping container(s), to ensure receipt of all components.
5. Save all shipping materials (any “bubble wrap” or plastic) for possible future use.
Store in a safe, dry location.

4.4.2 Locating the Panel

Mount the panel in a location within the environmental limits specified in the latest UL
Standard 864 for indoor/dry control panels. DO NOT locate the panel in a hazardous
area.

CAUTION: To comply with the latest NFPA and UL requirements for interconnection of
fire alarm control equipment, locate the SP40S Multi-Function Facility Communication
System in the same room, and within 20 feet of, a listed compatible fire alarm control panel.
Enclose the wiring in conduit and connect it properly to such control panel.

1. See Figure 11 for the panel mounting hole layout.

2. Mark and drill mounting holes for appropriate screws and anchors to ensure secure
mounting to the type of surface at the selected location.
3. Prevent dust and dirt contamination of the SP40S Multi-Function Facility
Communication System during installation. This contamination can interfere with
the operation and reduce the life of the equipment.
4. Open the door and remove the dead front panel, then mount the SP40S Multi-
Function Facility Communication System at the selected location. Use care to avoid
damage to the module during installation. Do not apply excessive pressure to the
PC board or its components, including field wiring terminals and connectors.

SP40S Multi-Function Communications System 38

 Installation

3/4" - 1" Conduit

Knockouts (18 Places)
14.00"

Grounding
Points

17.00"

Ground

Figure 11 SP40S Panel Mounting and Grounding/Conduit Locations

CAUTION: Use care when punching out knock-outs to avoid damage to internal
components.

SP40S Multi-Function Communications System 39

 Installation

Wire Distance Chart For 25V Speaker Line in feet

Watts 12 AWG 14 AWG 16 AWG 18 AWG
5 2179 1374 865 543
10 1090 687 432 271
15 726 458 288 181
20 545 344 216 136
25 436 275 173 109
30 363 229 144 90
35 311 196 124 78
40 272 172 108 68

Wire Distance Chart For 70V Speaker Line in feet

Watts 12 AWG 14 AWG 16 AWG 18 AWG
5 17087 10775 6780 4256
10 8543 5387 3390 2128
15 5696 3592 2260 1419
20 4272 2694 1695 1064
25 3417 2155 1356 851
30 2848 1796 1130 709
35 2441 1539 969 608
40 2136 1347 847 532

4.4.3 Installing Field Wiring Connections

NOTE: The terminal blocks on the SP40S Multi-Function Facility Communication System
are removable. To remove a terminal block, pull the block straight up from the circuit
board, as shown in Figure 12. Attach wires to the desired connections, then plug the
terminal block back on the board, being careful to match the pins.

Figure 12 Removable Terminal Block

SP40S Multi-Function Communications System 40

 Installation

NOTE: For power limited circuits, make sure that all input power sources (Alarm and
Trouble relay connections, NAC inputs, and auxiliary inputs) are power limited.
NOTE: The AC Power input wiring is non-power limited. Route it on the left side of the
enclosure, using one of the knockouts on the left side of the enclosure. Route all power
limited inputs and outputs on the right side and top of the enclosure.

Install field wiring in conduit when required, following the most current National Electrical
Code (NFPA-70) and local codes for the type of system being installed. Make all necessary
connections at any additional wiring or junction boxes.

CAUTION: Provide proper strain relief for all wiring not in conduit.

NOTE: Shielded wire is not required on any output circuits. If shielded wire is used, connect the
shields to the grounding points as shown in Figure 11.

4.4.4 Installing Strobe Connections

The Strobe Appliance Circuit consists of a NAC (8 to 33VDC) input and supervised NAC
(regulated 27VDC) output. The strobe output provides a synchronized output for compatible
Cooper Notification, synchronized strobes. When a synchronized signal from a previous
module is used, turn OFF SW9-position 1. This action also allows for pass-through of the
synchronized NAC Circuit on the RET connections. When connected with an SPB-80/4,
strobe compatibility is system-wide.

Section 11
Strobe Connections

Figure 13 Strobe Connections

1. Connect the Strobe Appliance Circuit to the Strobe output STB OUT connection on
TB12. Observe correct polarity. See Figure 4-1 for TB12’s location. Figure 4-4 is an
enlarged picture of the referred area. The Strobe Appliance Output Circuit is
supervised. A UL Listed 10K Ohm, ½ W EOLR is required at the end of the circuit
for proper supervision.
NOTE: The strobe output circuit can be activated four ways: (1) If the strobe output is to be
activated during a live PTT MIC page, turn ON SW3-position 9. (2) If the strobe output is to

SP40S Multi-Function Communications System 41

 Installation

be activated during an AUX activation, turn ON SW3-position 10. (3) If the strobe output is
to be activated when one or all the digital voice messages are initiated, operate DIP switch
SW9 as explained in Section 3.7.1. (4) The fourth way is to connect a NAC circuit input from
an FACP to STB IN as described below.
2. Connect Strobe Circuit input (8 to 33VDC) from the FACP or other UL Listed
control panels to the Strobe Input circuit (STB IN) connection on TB11. Observe
correct polarity. The maximum line impedance of the strobe circuits is 40 ohms.
3. Connect the FACP EOLR, additional appliances or additional SP40S panels to RET
connection on TB11.
• The Digital Voice Initiating Connections (IN1, IN2, IN3, IN4, IN5, IN6, IN7, and
IN8) can also initiate the strobe output circuit. Strobes can be initiated by the MIC,
AUX, IN1, IN2, IN3, IN4, IN5, IN6, IN7, and IN8.
• Positions 1, 2, 3, 4, 5, 6, 7, and 8 of SW3 control the strobe initiation for inputs IN1,
IN2, IN3, IN4, IN5, IN6, IN7, and IN8, respectively. If positioned in the ON or UP
position, the strobes operate during message playback.
• Position 9 of SW3 in the ON position initiates the strobe circuit during a PTT MIC
live announcement.
• Position 10 of SW3 in the ON position initiates the strobe circuit during an AUX
activation.
• Position 2 (ON) of SW9 selects the Cooper Notification Sync Mode during an alarm
strobe activation.

4.4.5 Installing Audio Output Connections

1. Connect the Audio Appliance Circuit to the Audio Output (AUDIO OUT)
connection on TB4. See Figure 10 for TB4’s location. Figure 14 is an enlarged picture
of the referred area. The Audio Output is supervised. A UL Listed 10K Ohm, ½ W
EOLR is required at the end of the circuit for proper supervision.

Section 4
Audio Output
Connections

Figure 14 Audio Output Connections

2. Select the proper output voltage (25V or 70V) using the Audio Output Select Jumper
J1.

SP40S Multi-Function Communications System 42

 Installation

4.4.6 Installing Auxiliary Circuit Connections

Refer to the Remote MIC or RMX Installation Manual for proper connections from 24V
OUT, AUX IN, and CC/NAC to these products. All connections to these products are made
from TB6.

4.4.7 Installing Audio Input Connections

The SP40S panel has thirteen inputs. The highest priority input is the on board Push-To-Talk
Microphone; it overrides all other audio inputs. The second highest priority input is the
AUX. This could be a Remote MIC or RMX. Next are the IN1, IN2, IN3, IN4, IN5, IN6,
IN7, and IN8 respectively, followed by Night Ring (NR), Telephone Page (TEL), and
Background Music (BGM). Background Music is muted when any other audio input is
initiated. Night Ring (NR), Telephone Page (TEL), and Background Music (BGM) are
considered non-alarm audio and operate only when the panel has VAC applied.

4.4.8 Installing Digital Voice Initiating Connections

The Digital Voice Initiating Connections (IN1, IN2, IN3, IN4, IN5, IN6, IN7, and IN8)
provide the initiation of the stored messages in the Digital Voice Section of the SP40S
panel. Each initiation circuit requires a Contact Closure input to trigger the respective voice
message. Additionally, each initiating circuit is supervised for an open. A 10k Ohm, ½ W
EOLR is required for each input that is supervised. If an input is not being used, supervision
can be turned off via DIP switch (SW7, positions 1-8).
NOTE: Do not connect a NAC or DC voltage directly to the Digital Voice Inputs. A relay
is required.

Sections 7 and 8
Internal Digital Voice
Connections

Figure 15 Digital Voice initiating Connections

• While observing correct polarity, connect the Digital Voice Initiating connections
(IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8) to the connections on TB7 or TB8 as
desired. See Figure 10 for TB7 and TB8’s locations. Figure 15 is an enlarged picture
of the referred area.

4.4.9 Installing Ancillary Audio Input Connections

The SP40S panel has three ancillary audio inputs. Listed in order of priority, they are Night
Ring (NR), Telephone Page (TEL), and Background Music (BGM). These inputs do not
operate when the SP40S panel is in the alarm condition or when the input voltage
(VAC) is not applied and the panel is on battery backup. In addition, these inputs are not
supervised.

SP40S Multi-Function Communications System 43

 Installation

The Telephone Page input requires input from a Telephone Page Port. The Night Ring input
requires a dry contact closure. The Background Music input requires a line level, 600 Ohm,
1Vrms signal.
1. Connect Telephone Page Input (TEL) to TB5. See Figure 10 for TB5’s location.
Figure 16 is an enlarged picture of the referred area.
2. Connect Night Ring Input (NR) to TB5.

Section 5
Night Ring, Telephone
Page, Background
Music Connections

Figure 16 Ancillary Audio Input Connections

NOTE: The Night Ring (NR) input requires a contact closure from the phone system to
activate. The NR must be connected to the phone line in the same room.
NOTE: When installed in New York City, the background music feature and telephone
paging features are not permissible.

3. Connect Background Music Input (BGM) to TB5.

WARNING: EXCESSIVE BGM VOLTAGE INPUT CAN CAUSE AMPLIFIER

FAILURE. MAKE SURE THAT THE PREFERRED AUDIO SOURCE OUTPUT
FOR THE BGM INPUT OF THE SP40S PANEL (CD PLAYER, TUNER,
EQUALIZER, ETC.) IS A FIXED LINE LEVEL VOLTAGE LESS THAN 2.5V
PEAK TO PEAK OR 300MV RMS. AUDIO SOURCES MARKED “LINE LEVEL
OUTPUT” ARE TYPICALLY WITHIN THIS LIMIT. AUDIO SOURCES WITH
OTHER THAN FIXED LINE LEVEL OUTPUTS (THAT IS, ADJUSTABLE
SPEAKER OUTPUTS, ETC.) REQUIRE THAT THE AUDIO SOURCE BE
ADJUSTED USING A MULTI-METER ACROSS THE OUTPUT OF THE SIGNAL
SOURCE (SEE BELOW). ONCE THE LEVEL HAS BEEN SET PROPERLY,
SECURE THE ADJUSTABLE AUDIO SOURCE SO THAT THE LEVEL CANNOT
BE INADVERTENTLY CHANGED. FAILURE TO SET ADJUSTABLE AUDIO
SOURCES APPROPRIATELY OR FAILURE TO SECURE AUDIO ADJUSTABLE
SOURCES CAN LEAD TO FAILURE OF THE AMPLIFIER SECTION OF THE
SP40S PANEL. THIS FAILURE, IN TURN, COULD RESULT IN SERIOUS INJURY
OR DEATH TO YOU AND/OR OTHERS.

SP40S Multi-Function Communications System 44

 Installation

4.4.10 Setting Adjustable Audio BGM Sources

NOTE: Use a good multi-meter that provides true RMS readings in the AC voltage scale
and calculates the results through average sampling. Some multi-meters can select instant
or average sampling readings. Always do this adjustment in the “averaging” mode. Most
digital multi-meters use the average sampling method in the “AC Volts RMS” setting.

1. Ensure that power is disconnected from the SP40S panel.

2. Set the Audio Source volume control to the minimum setting.
3. Connect the Audio Source output to the BGM input terminals (TB5) on the panel.
4. Set the multi-meter to the AC Volts scale, which is capable of reading 300mV RMS.
5. Connect the multi-meter across the BGM terminals on the panel.
6. Adjust the output control of the audio source to obtain a reading of 300mV RMS on
the multi-meter.
7. Secure the output control of the audio source so that it cannot be changed
inadvertently.
8. Disconnect the multi-meter. The output of the Audio Source is now correctly set for
the SP40S BGM input.

4.4.11 Installing Alarm, System Trouble, and AC Trouble Output Connections

The Alarm Form C relay contacts change state when a MIC, AUX, or a DV (Digital Voice)
message is active. The AC Trouble Form C relay contacts change when primary power is
missing or low. The System Trouble Form C relay contacts change state when the panel
goes into any trouble condition. For additional information, see Table 4. An AC Loss can be
delayed 170 minutes before it is reported as a system trouble (SW2 – Position 2 set to ON).
1. Connect the external alarm circuit to the proper Alarm (ALM) connections. See
Figure 10 ,TB1, Section 1, for location.
2. Connect the external Trouble circuit to the proper Trouble (TRB) connections.
3. Connect the SP40S panel to earth ground, following the National Electrical Code and
local codes for the type of system being installed. Wire gauge selection of the earth
ground wiring involves consideration of all factors, including maximum allowable
wire resistance and length. The panel is tied to earth ground by connecting the
ground terminals to an earth ground. The location of the ground terminals within the
panel is shown in Figure 22.

CAUTION: Do not connect input voltage to any equipment until the field wiring
has been tested, inspected and approved.

SP40S Multi-Function Communications System 45

 Installation

4. Check the integrity of all field wiring. Confirm that the specified cable is installed,
and that there is continuity between required points (no open circuits), with no
unwanted shorts to other conductors, chassis, or earth ground.
a) Verify that the field wiring complies with the instructions of this manual and
the detailed wiring diagram prepared for this installation.
b) Ensure that no unwanted voltages are present on circuit conductors and
ground.
c) Test all ungrounded connectors for electrical isolation from ground.
d) Measure and record the resistance of each NAC circuit. Conduct this test
reversing polarity.
5. Perform Ground Fault Installation procedure as described in Section 4.7.
6. Calculate and install properly sized backup batteries as described in Section 4.8.3.
The SP40S panel is UL approved for 24VDC for a maximum of 33 Ah. Batteries
greater than 12 Amp-Hour (Ah) are required to be installed in a UL listed battery
box. The enclosure can accommodate up to 12 Ah.

WARNING: TWO DIFFERENT SOURCES OF POWER SHOULD BE CONNECTED

TO THIS UNIT. DISCONNECT BOTH SOURCES OF POWER BEFORE
SERVICING. FAILURE TO DISCONNECT BOTH POWER SOURCES BEFORE
SERVICING COULD RESULT IN SERIOUS INJURY, OR DEATH TO YOU
AND/OR OTHERS.

WARNING: ALWAYS APPLY AC VOLTAGE BEFORE APPLYING BATTERY

BACKUP VOLTAGE. FAILURE TO DO SO MAY CAUSE DAMAGE TO THE SP40S
PANEL.

7. Perform System Checkout procedures as described in Section 4.6.

4.5 Wiring the System

4.5.1 Wiring Guidelines

Although the SP40S panel incorporates signal verification and noise filtering circuitry on its
inputs, induced voltages or noise on the input wiring can cause improper operation.
Therefore, use shielded twisted pair wire for all dry contact input wiring.
• Connect the shield of each cable only at one end.
• Connect each shield of each cable that connects to the panel to the grounding points
provided near the knockout locations on the chassis (see Figure 11).
The National Electrical Code defines two types of circuits for protective signaling systems:
power limited circuits and non-power limited circuits. All outputs (STB OUT, AUDIO
OUT, and ± 24VDC auxiliary power source) are either Class 2 or Class 3 power-limited
circuits.

SP40S Multi-Function Communications System 46

 Installation

WARNING: ROUTE ALL SP40S MULTI-FUNCTION FACILITY

COMMUNICATION SYSTEM AUDIO WIRING AWAY FROM ANY HIGH
VOLTAGE OR HIGH CURRENT WIRING (SUCH AS AC OR DC POWER WIRING,
AUDIO POWER WIRING, AND MOTOR OR RELAY ACTUATION WIRING).
FAILURE TO DO SO MAY CAUSE ELECTRICAL SHOCK, RESULTING IN
SERIOUS INJURY OR DEATH TO YOU AND/OR OTHERS.

CAUTION: The National Electric Code limits the maximum number of conductors that
can be installed in conduit and wiring boxes depending on the size of the conduit, the
volume of the boxes, and the gauge of the wire used. Make sure that wiring used for
SP40S installation complies with the latest NEC, NFPA, Local, State, County, or
Province requirements. wiring has been tested, inspected and approved.

4.5.2 Field Wiring Connections

All SP40S wiring terminals are designed to accept #12 AWG through #18 AWG wiring
for one wire per terminal or #16 AWG to #18 AWG for two wires per terminal. Proper
wire gauge considerations for the Notification Circuit must take into account current
requirements versus length of run.
NOTE: Only speakers with DC blocking capacitors provide for proper speaker supervision.

4.5.3 Preparing a System Wiring Diagram

Prepare a system-wiring diagram to include all Notification Appliances, and internal
connections and power sources as required.
NOTE: Separate the AC input power wiring from the other input and output wiring. Wire
the AC input power to the left side of the motherboard (Figure 22) and the other input and
output wiring to the right..

4.5.4 Visual Notification Appliance Output Wiring

Wire gauge selection involves consideration of all factors including, wire loop length,
maximum current draw of each appliance, number of appliances, and maximum voltage
drop allowable.
• Strobe NAC has a regulated 24VDC, 2.0 Amps maximum output.
• Strobe NAC meets Class B supervision requirements for notification appliance
circuits.
• For the strobe output circuit, install a UL Listed 10K Ohm, ½ W EOLR across the
last visual notification appliance. If the output is unused, place a UL Listed 10K
Ohm, ½ W EOLR across the output terminals.

SP40S Multi-Function Communications System 47

 Installation

4.5.5 Speaker Notification Appliance Output Wiring

Wire gauge may vary for each audio appliance output on the panel. When:
• Speaker (with transformer) appliances are used with supervised audio amplifier
module. Wire gauge selection involves consideration of all factors including, wire
length, appliance power ratings, and the number of appliances.
• The amplified output is either a selectable 25 or 70.7Vrms audio output, rated for 40
watts maximum.
• The output meets Class B supervision requirements for notification appliance
circuits.
• To meet Class A requirements, a Cooper Notification splitter (SP4-A/B or SP4-APS)
is required.
• For the audio output circuit, install a UL Listed 10K Ohm, ½ W EOLR installed
across the last notification appliance. If the output is unused, place a UL Listed 10K
Ohm, ½ W EOLR across the output terminals.

4.5.6 Wiring Diagrams for Audio/Visual Notification Appliances

+ UL LISTED 10K OHM, 1/2 W

STROBE END OF LINE RESISTOR
-
Figure 17 Wiring Diagram for Visual Only Notification Appliances

CAUTION: Do not loop wire under terminals. Break wire run to provide supervision
of the connection.

+ UL LISTED 10K OHM, 1/2 W

AUDIO END OF LINE RESISTOR
-
+ UL LISTED 10K OHM, 1/2 W
STROBE END OF LINE RESISTOR
-

Figure 18 Wiring Diagram for Combination Audio/Visual Notification Appliances

CAUTION: Do not loop wire under terminals. Break wire run to provide supervision
of the connection.

SP40S Multi-Function Communications System 48

 Installation

+ UL LISTED 10K OHM, 1/2 W

AUDIO END OF LINE RESISTOR
-
Figure 19 Wiring Diagram for Audio Only Notification Appliance Output

CAUTION: Do not loop wire under terminals. Break wire run to provide supervision
of the connection.

4.5.7 Wiring the Alarm Output Contact

The location of the Alarm Output Connections (TB1) is shown in Figure 10. A magnified
view of this area on the motherboard is shown in Figure 20.
• Wire gauge selection of the Alarm Status output contact wiring involves
consideration of all factors including, wire loop length, maximum current capacity,
and maximum voltage drop allowable.
• The Alarm Status output contact is Form C, rated for 2.0 amps at 24VDC, resistive
load.
• For terminal connection details of the Alarm Status output contact (shown in the
non-alarm mode), see Figure 20.
• Contacts are duplicated for ease of IN and OUT wiring.
• An external 24VDC or the internal 24VDC connection (TB1) can be used to power
non-supervised Alarm appliances.

Section 1
Alarm Connections

Figure 20 Alarm Connections

SP40S Multi-Function Communications System 49

 Installation

4.5.8 Wiring the System Trouble Connections

The locations of the System Trouble (Trouble Status Output) Connections (TB2) are shown
in Figure 10. A magnified view of this area on the motherboard is shown in Figure 21.
• Wire gauge selection of the system Trouble Status output contact wiring involves
consideration of all factors including, wire length, maximum current capacity, and
maximum voltage drop allowable.
• The system Trouble Status output contact is Form C, rated for 2.0 amps at 24VDC,
resistive load.
• For a detail of the system Trouble Status output contact terminal connections (shown
in the trouble position), see Figure 21 below.
• An external 24VDC or the internal 24VDC connection (TB1) can be used to power
Trouble indicating appliances.

Section 2
System Trouble Connections

Figure 21 System Trouble Connections

(Trouble Status Relay Contact)

4.6 Performing System Checkout

For guidelines on testing notification systems, refer to the latest NFPA 72 code.

4.6.1 System Control Settings

Figure 4 thru Figure 8 show the location of the controls used to configure the SP40S Multi-
Function Facility Communication System. Table 4 identifies and explains the functions of
the terminal blocks, Section 3.7 the other user settings. The following procedure is a basic
setup for the panel.
1. Ensure that the AC and Battery Power are not connected.
2. Plug in the microphone.
3. Select the proper audio output (25V or 70V) on J1 Audio Output Select.
4. Connect the speaker circuit(s) to terminal block TB4 AUD OUT. Verify that the
speaker circuit has a UL Listed 10K Ohm, ½ W EOLR.

SP40S Multi-Function Communications System 50

 Installation

5. If applicable, connect the strobe circuit to TB12 STB OUT. Verify that the strobe
circuit has a UL Listed 10K Ohm, ½ W EOLR.
6. If Strobe synchronization is to be defeated, turn OFF positions 1 and 2 of SW9
Strobe Synchronization Defeat.

4.6.2 Checkout Procedure

WARNING: ALWAYS CONNECT THE AC POWER SOURCE BEFORE

CONNECTING THE BATTERY BACKUP POWER. ALWAYS DISCONNECT THE
AC POWER SOURCE BEFORE DISCONNECTING THE BATTERY BACKUP
POWER.

NOTE: All terminal blocks, jumpers, switches, LEDs, Fuses, and Potentiometers are
illustrated in Figure 4 thru Figure 8.
• Connect the interface ribbon cable to J6.
• Connect AC power, then connect the batteries.
When the AC power source is applied to the panel, the battery voltage check circuitry
is activated. If batteries are not connected within 20 seconds, the panel trouble circuit
activates. The battery voltage check circuitry re-checks for batteries every two
minutes. If the batteries are installed during the two-minute period, the panel remains
in trouble mode until the next re-check.
• D100 PWR LED and POWER ON (Interface) LED should be “ON” to indicate
normal operation.
• If SYSTEM TROUBLE (Interface) LED (Yellow) is “ON,” and the internal sounder
is operating, a trouble condition is indicated.
• In such a case, STOP TESTING. Refer to Chapter 8 of this manual, then
troubleshoot and correct the problem before you resume testing. See Figure 7 for
location of LEDs.
• Perform the following tests:
4.6.2.1 A Microphone Test
1. Press the push-to-talk Button on the microphone and speak into the microphone.
2. Ensure your voice can be heard on the output speaker circuit.
4.6.2.2 B Auxiliary Test
1. If a Remote MIC or RMX is being used, initiate a Remote MIC and speak into the
microphone.
2. Ensure your voice can be heard on the output speaker circuit.
4.6.2.3 C Digital Voice Message Test
Message 1
1. Press the top message button. The message should be heard on output speaker
circuit. The top message button/LED on the interface should blink to indicate the
button has been pressed.

SP40S Multi-Function Communications System 51

 Installation

2. Test the strobe circuit associated with the first message by switching DIP switch
SW3 (DV/Strobe Select), position 1 “ON.” The STB LED on the interface (Red)
turns “ON.” If the strobe circuit is attached to TB11, strobes flash.
3. Turn OFF message 1 by pressing the top message button again or removing contact
closure from IN1. The message plays to completion at least three times. If DIP
switch SW2 (DV/Strobe Select) position 1 is ON, the strobe circuit is ON until the
message is complete.
4. Turn DIP switch SW3, position 1 OFF.
5. Apply contact closure activation to TB7 (IN1) connection (Figure 15). The message
should be heard from output speaker circuit. The top message button/LED on the
interface should illuminate steadily to indicate contact closure is present.
6. Test the strobe circuit associated with the first message switching DIP switch SW3
(DV/Strobe Select), position 1 “ON.” The STB LED (Red) turns “ON.” If the strobe
circuit is attached to TB2, strobes flash.
7. Remove the contact closure from TB7 (IN1). The message plays to completion at
least three times. If DIP switch SW3 (DV/Strobe Select) position 1 is “ON,” the
strobe circuit is ON until the message is complete. The top message button/LED on
the interface should turn OFF once the contact closure is removed.
8. Turn DIP switch SW3, position 1 OFF.
9. Perform Steps 3 through 10 on Messages 2 and 3. Use Table 5.
Table 5 Digital Voice Message Tests
Message SW3 DV/Strobe
TB4 Interface Button
Number Select

Message 1 IN1 Top Position 1

Message 2 IN2 Second Position 2

Message 3 IN3 Third Position 3

Message 4 IN4 Fourth Position 4

Message 5 IN5 Fifth Position 5

Message 6 IN6 Sixth Position 6

Message 7 IN7 Seventh Position 7

Message 8 IN8 Eighth Position 8

4.6.2.4 D Strobe Circuit Test

1. If the Strobe circuit is being used separately, apply 24VDC from TB4 or TB6 to STB
IN connection TB12 (Figure 13). The Strobes on the Strobe Output Circuit should
flash. Also, the SP40 interface Strobe Active LED should illuminate.
2. Remove the voltage.

SP40S Multi-Function Communications System 52

 Installation

4.6.2.5 E Night Ring Test

Test Night Ring by shorting NR connection TB5 (Figure 16). The chime sound should be
heard from the output speaker circuit.
4.6.2.6 F Telephone Page Test
If the Telephone Page circuit is used, make a telephone page from the phone system. The
page should be heard from the AUDIO OUT speaker circuit.
4.6.2.7 G Background Music Test
1. If the Background Music (BGM) circuit is used, energize the music source. The
music source output should be heard from the output speaker circuit. The Installation
and Checkout procedure is now complete.
2. Make and check final connections, then replace the dead front panel.

WARNING: PERFORM MANDATORY TESTING OF ALL PROTECTIVE

SIGNALING SYSTEMS AS REQUIRED. TEST ALL PROTECTIVE SIGNALING
SYSTEM EQUIPMENT USING QUALIFIED PERSONNEL AT LEAST TWICE A
YEAR FOR PROPER OPERATION, OR MORE OFTEN IF REQUIRED BY CODES,
REGULATIONS, AND LAWS. FAILURE TO MAINTAIN AND TEST PROTECTIVE
SIGNALING SYSTEM EQUIPMENT CAN RESULT IN NOT DETECTING
EQUIPMENT FAILURE THAT CAN CAUSE SERIOUS PERSONAL INJURY OR
DEATH TO YOU AND/OR OTHERS DURING AN EMERGENCY SITUATION.

4.7 Ground Fault Detection

Ground fault detection sensitivity is a minimum of 40K Ohms for Class B, Style Y
connections.

4.8 Battery Care and Backup Battery Calculations

4.8.1 Caring for Sealed Lead Acid Batteries

Sealed lead acid batteries are designed to operate in standby service for approximately five
years. This is based upon a normal service condition where there is an ambient temperature
of 20 degrees C (68 degrees F) and batteries are completely discharged once every three
months. Length of service life is directly affected by the number of discharge cycles,
depth of discharge, and ambient temperature.

Use Guidelines
• Avoid installation and/or operation in close proximity to heat sources. While the
operating temperature range is 0 to 49 degrees C (32-120 degrees F), battery life is
maximized at an ambient temperature of 20 degrees C (68 degrees F).
• Batteries may generate ignitable gases. Because of this, install batteries in a well-
ventilated location, away from spark producing equipment.
• DO NOT install batteries in an atmosphere where organic solvents or adhesives may
be present. DO NOT clean the batteries with oils, thinners, or similar substances.

SP40S Multi-Function Communications System 53

 Installation

The case and cover of the batteries are ABS plastic resin, which may suffer damage
from these chemicals.
• DO NOT install batteries in a heavy vibration or shock location.
• ALWAYS wear insulated gloves when handling batteries.
• DO NOT use together batteries of different capacities, age, or manufacture.
WARNING: DO NOT CRUSH, INCINERATE, OR DISMANTLE BATTERIES. THE
ELECTROLYTE CONTAINS SULFURIC ACID, WHICH CAN CAUSE SERIOUS
DAMAGE TO EYES AND SKIN. IF CONTACT DOES OCCUR, FLUSH WITH
WATER AND SEEK IMMEDIATE MEDICAL ATTENTION.

4.8.2 Storing Batteries

• For batteries that are to be stored for an extended period of time, give a supplemental
charge monthly.
• NEVER store batteries in a discharged condition.
• The self-discharge rate of batteries is approximately 3% per month when the storage
temperature is maintained at 20 degrees C (68 degrees F). The self-discharge rate
varies depending upon temperature. Cooler temperatures cause the self-discharge
rate to decrease. Warmer temperatures cause the self-discharge rate to increase.

4.8.3 Calculating Backup Battery Requirements

A Worksheet for assisting in calculating battery backup is available in Chapter 11.
Due to the current drain on the battery, the maximum battery size for the SP40S Multi-
Function Facility Communication System is 33 Amp-Hours (Ah). The enclosure can
accommodate up to 12 Ah. Batteries greater than 12 Amp-Hours (Ah) are required to be
installed in a UL listed battery box.
It is necessary to calculate the current draw for battery backup requirement. The current
requirement depends on the system configuration and the appliances connected to the
Speaker output circuits. Battery Backup current has two separate calculations that are added
together: Standby Current and Alarm Current.
4.8.3.1 A Standby Current
The Standby Current consumes the largest part of the storage battery capacity. The Standby
Current of the SP40S Multi-Function Facility Communication System is 0.130 Amps.
Multiply this value by the number of standby hours required. Normally this is 24 hours. This
represents the total Standby current in Amp-Hours for the panel.
4.8.3.2 B Alarm Current
The maximum Alarm Current for the SP40S Multi-Function Facility Communication
System is 4.66 Amps (2.16 Amps for audio, 2.0 Amps for strobe, and 0.5 Amps for auxiliary
power).
1. Calculate the strobe output current by adding the current draw of all strobes. Current
draw is in Amps.

SP40S Multi-Function Communications System 54

 Installation

2. Calculate speaker output current by totaling all the speaker wattage settings.
Multiply the sum by 0.054. The result is the current draw in Amps.
3. Add the strobe current, the speaker current, and auxiliary current together. The result
is the total Alarm Current in Amps.
4. Alarm circuits are required to operate for 15 minutes on battery power. Multiply Step
3 by 0.25 hrs. The result is the total Alarm Capacity Required in Amp-Hours.
4.8.3.3 Battery Calculations
Good engineering practices recommend the total Amp-hours required for backup should not
exceed 90% of the Backup Battery capacity. The SP40S Multi-Function Facility
Communication System has been UL approved for a maximum of 33 Ah batteries. The
enclosure can accommodate up to 12 Ah. Batteries greater than 12 Amp-Hours (Ah) are
required to be installed in a UL listed battery box.
1. Add the total Standby Capacity Required to the total Alarm Capacity Required.
2. Multiply Step 1 by 1.25. This is the minimum Backup Battery requirement for this
panel.
3. Record results on worksheet.

4.9 Installing AC Power and Batteries

NOTE: Power-limited and non-power limited wiring must be separated. Wire non-power
limited wiring (AC power and battery) to the left of the motherboard. Wire power limited
wiring to the right and top of the motherboard.
WARNING: TWO DIFFERENT SOURCES OF POWER SHOULD BE CONNECTED
TO THIS UNIT. DISCONNECT BOTH SOURCES OF POWER BEFORE
SERVICING. FAILURE TO DISCONNECT BOTH POWER SOURCES BEFORE
SERVICING COULD RESULT IN SERIOUS INJURY OR DEATH TO YOU AND/OR
OTHERS.

CAUTION: Observe correct polarity requirements on all connections. Failure to do so

may damage the equipment.

CAUTION: Always apply AC voltage before applying battery backup voltage. Failure
to do so may cause damage to the SP40S Multi-Function Facility Communication
System.

4.9.1 Installing AC Power

1. Refer to Figure 22 and connect the line and neutral input wiring to the L (Line) and
N (Neutral) terminals on the terminal block TB9 (see Figure 4 for location) in the
lower left corner of the chassis.
2. Ensure that the ground input wiring is connected to the ground terminal (TB9) on the
left side of the chassis.

SP40S Multi-Function Communications System 55

 Installation

AC Field Wiring
(non-power limited)

LINE, GROUND
and NEUTRAL

Thread wire out

knockout on the
left side of the
enclosure.
Figure 22 VAC Input Connection

4.9.2 Installing Batteries

NOTE: Batteries are not supplied with the SP40S Multi-Function Facility Communication
System and must be purchased separately.
1. Connect the supplied red battery wire to the (+) terminal and the supplied black
battery wire to the (–) terminal of TB10 (see Figure 23).
2. Run jumpers along the bottom of the chassis in the battery compartment.

To Negative To Positive
(-) of battery (+) of battery
terminal terminal
(Black) (Red)

SP40S Multi-Function Communications System 56

 Installation

Figure 23 Battery Wire Connections

3. Refer to Figure 24 and place one 12 Volt battery with the battery terminals on top and
to the right. Place the second battery to the right of the first battery with the battery
terminals on top and to the left.

CAUTION: Always install the two batteries with the battery terminals pointing to the
center and in the upright position as shown in Figure 24. Failure to do so may cause a
short circuit which may damage the SP40S panel or batteries and cause the panel to fail
to operate in an emergency condition.

Short Jumper
(Supplied)
+
-
-
+
To Negative (-)
of Battery
Terminal (TB10)
on bottom of
motherboard
To Positive (+)
of Battery
Terminal (TB10)
on bottom of
motherboard
Figure 24 Battery Alignment and Jumper Connection
4. Connect the short jumper (included) to the back terminals (negative to positive) of
the two batteries as shown in Figure 24. This connects the 12VDC batteries in series
in order to produce 24VDC.
5. Place the batteries in the battery compartment with the battery terminals and jumper
facing “UP” or toward the top of the SP40S panel. Make sure that the red and black
battery jumpers are clear of the batteries.
6. Attach the red and black battery wires (red to (+), black to (–)) to the proper battery
terminals.

SP40S Multi-Function Communications System 57

 Operation

5. Operation
5.1 Introduction
This chapter describes the operating characteristics of the SP40S Multi-Function Facility
Communication System. Included is information about the following panel features:
• Supervision
• Audio Notification Appliance Output Circuit Supervision
• Amplifier Supervision
• Actions that Initiate Alarms

5.2 User Interface

The User Interface on the SP40S displays the basic status of the unit as well as providing a
limited number of user controls. The User Interface includes a Microphone and the manual
activation or recording of the eight messages. There is also a button to silence the audible
trouble indicator. Status indicators include POWER ON, SYSTEM TROUBLE, AC
TROUBLE, ALARM ACTIVE, and STROBE ACTIVE (see Figure 3).

5.3 Supervision
A SYSTEM TROUBLE LED indicates that the supervisory functions have detected a
malfunction in the panel. When a trouble condition is detected, the panel may not be able to
receive and/or broadcast messages from the control panel.
If a trouble condition is detected by any of the supervisory functions, the internal sounder
operates the panel Form C TROUBLE relay (normally energized), changes state, and the
yellow SYSTEM TROUBLE LED turns “ON.” The Trouble Status Relay (TB2) must be
properly connected to and used by the control panel to indicate a system trouble. At the
same time, one of the yellow trouble location LEDs identifies the location of the trouble
condition. The internal sounder can be silenced for 20 hours by depressing the “Trouble
Acknowledge” Switch (SW1, on the User Interface). Any subsequent troubles cause the
sounder to be re-activated. If a trouble condition is indicated, follow the procedures in
Chapter 8 "Troubleshooting.”
An AC Loss can be selected to be reported as a system trouble after 170 minutes (SW2-
Position 2 = ON). This is desirable for off-premise trouble reporting. If SW2-Position 2 is
OFF, AC Loss is reported as a system trouble after 30 seconds.

WARNING: DO NOT LEAVE THE SP40S PANEL IN A TROUBLE CONDITION, AS

IT MAY NOT PLAY WARNING MESSAGES, WHICH COULD RESULT IN
SERIOUS INJURY OR DEATH TO YOU AND/OR OTHERS. IF THE PANEL
INDICATES A TROUBLE CONDITION: (1) PROVIDE UL REQUIRED
ALTERNATIVE SIGNALING AND (2) HAVE QUALIFIED SERVICE PERSONS
IMMEDIATELY REPLACE UNIT(S) THAT HAVE MALFUNCTIONED.

SP40S Multi-Function Communications System 58

 Operation

WARNING: MESSAGES REQUESTED BEFORE AND DURING A TROUBLE

CONDITION MAY NOT BE HEARD, WHICH COULD RESULT IN SERIOUS
INJURY OR DEATH TO YOU AND/OR OTHERS. IF MESSAGES REQUESTED
BEFORE AND DURING A TROUBLE CONDITION ARE STILL NECESSARY,
REPEAT THEM WHEN THE SP40S PANEL IS RETURNED TO NORMAL.

5.3.1 Visual Notification Appliance Output Circuit Supervision

The Visual Notification Appliance Output Circuit uses Class B, Style Y wiring, and is
supervised for open and short circuits when the output is de-energized. Output circuit
supervision requires installation of UL Listed 10K Ohm, ½ W EOLR on the output circuit.
A sensed strobe short circuit trouble illuminates D96 STB SHORT LED. A sensed strobe
open circuit trouble illuminates D97 STB OPEN LED. See Figure 8-1 for LED location.

5.3.2 Audio Notification Appliance Output Circuit Supervision

The Audio Notification Appliance Output Circuit uses Class B, Style Y wiring, and is
supervised for open and short circuits when the output is de-energized. Output circuit
supervision requires installation of UL Listed 10K Ohm, ½ W EOLR on the output circuit.
A sensed open circuit trouble illuminates D1 AUDIO OPEN LED. A sensed strobe short
circuit trouble illuminates D2 AUDIO SHORT LED. See Figure 26 for LED location.

5.3.3 Amplifier Supervision

An inaudible supervisory tone plays through the Amplifier section during standby for
supervision purpose. Any sensed trouble illuminates D5 “AMP” LED steadily. See Figure 8-
1 for LED location.

5.3.4 Ground Fault Supervision

The SP40S Multi-Function Facility Communication System supervises for Ground Fault
conditions on Class B, Style Y field wiring that is not electrically isolated. The supervised
wiring includes contact inputs, visual NAC circuits, audio NAC circuits, amplified speaker
NAC circuits, and trouble audible output circuits. All other wiring is electrically isolated. If
a Ground Fault condition exists, D67 GF LED illuminates. See Figure 26 for LED locations.

5.4 Actions that Initiate Audio Alarms

Table 6 indicates what can initiate an alarm condition and the resulting SP40S Multi-
Function Facility Communication System actions.
Table 6 Audio Alarm Conditions and Results
PRIORITY INITIATING
RESULT
OF EVENT ACTION
Panel microphone push-to-talk button,
1 Panel microphone live voice broadcast enabled.
is depressed.
Remote Microphone push-to-talk
2 Remote MIC live voice broadcast is enabled.
button is depressed
Digital Voice circuit Contact Closure
3, 4, 5, 6, 7, 8, Selected Digital Voice enabled. If digital voice is
inputs. (IN1, IN2, IN3, IN4, IN5, IN6,
9, 10 non-operational, program tone broadcasts.
IN7, IN8)

SP40S Multi-Function Communications System 59

 Operating Procedures

6. Operating Procedures
6.1 Making Live Announcements
1. Hold the on board or remote microphone within 2 inches from your mouth, press the
Push-To-Talk (PTT) switch and begin speaking. (For best results, hold the
microphone within a half inch from your mouth.)
2. When finished, release the PTT switch and return the microphone to its holder.
NOTE: If the on-board microphone push-to-talk button is depressed and remains depressed
for two and a half minutes, the microphone circuit switches automatically to the selected
supervision tone.

6.2 Recording Digital Voice Messages

The Digital Voice section of the SP40S panel contains a digital voice memory chip that
contains the digital voice program and the voice messages. The memory chip comes with
eight messages installed. The DV Memory Chip can be removed and the messages remain
on the chip. If tailored messages (messages with tones) are required from Cooper
Notification Inc., the new chip can be installed when received.
• The message chip memory is divided into eight segments. Each segment is
prioritized 1 through 8, matching the inputs IN1 through IN8.
• If the IN8 message is playing and a higher priority message is initiated, the message
on IN8 stops immediately and the higher priority message plays.
• As long as the contact closure voltage is applied to the input, the message repeats.
When the voltage is removed, the message plays to the end and stops. The message
plays a minimum of three times completely.
• Each message can be selected to have a code3 pre-alert tone, a continuous pre-alert
tone, a code 4 pre-alert tone or no pre-alert tone. This is based on SW4 and SW5,
positions 1-8 settings.
• The frequency of the pre-alert tone can be selected to be 1kHz, or 520Hz for sleeping
applications. This is based on SW4 position 10 setting (see table SW4, section 3.7.1)
• Post-tones are also selectable via SW5, position 9. Post-tones match pre-tones on an
individual message basis.
• When the Digital Voice Section is set up for record mode, field recording is limited
to 30-second segments.
• When using the code 4 CO annunciation feature, all CO voice messages must be the
highest voice message priorities. For example, if you have two CO messages, five
fire messages and one general message, set the two CO messages for IN1 and IN2,
followed by the fire messages IN3-IN7 and the general message as IN8.

SP40S Multi-Function Communications System 60

 Operating Procedures

6.3 NOTE: If the Digital Voice Section fails, the SP40S panel plays the
selected tone (Code 3 Tone or Slow Whoop). See Figure 6 for the location of
SW3-position 9. Recording Messages on the Digital Voice Section

CAUTION: Recording of any new message permanently erases the previous message.
If a Cooper Notification factory prerecorded fire or emergency message or a tailored
message is accidentally or intentionally erased, a new factory recorded message kit
must be purchased to restore the message.

• Decide which message segment to make the recording on.

• Read through this procedure carefully before attempting a recording.
• Identify all components mentioned.

1. Remove the DV Record Jumper JP5 (see Figure 5). Place jumper in a secure place;
this is replaced at the end of the recording procedure.
2. Connect 1/8” line level audio to audio jack (J2) on the left side of the SP40S unit.
3. Press and hold the RECORD button on the user interface.
4. Determine which one of the eight messages you wish to record.
5. Press the message button on the interface corresponding to the message you wish to
record. The Record LED illuminates and recording begins. You may release the
record button at this point.
6. When the message concludes, press the illuminated message button again. Recording
then stops.
7. Check the recorded message by pressing the proper DV message button. The
message plays in its entirety at least three times.
8. For additional message recording, repeat steps 2 through 7.
9. When recording is done, replace DV Record Jumper (JP5).

SP40S Multi-Function Communications System 61

 Operating Procedures

6.4 Verifying Messages

NOTE: Verify that DIP switch JP5 is in place. See Figure 5 for location.

Message 1
Message 2
Message 3
Message 4
Message 5
Message 6
Message 7
Message 8

Figure 25 SP40S User Interface

1. Press the button of the desired DV message. The message will begin playback and
the corresponding DV message LED will blink (LED will be steady with model
SP40S(E)-D).

2. Press the blinking button again to deactivate the DV message. The message plays in
its entirety a minimum of three times.

SP40S Multi-Function Communications System 62

 Periodic Testing and Maintenance

7. Periodic Testing and Maintenance

7.1 Introduction
• Conduct periodic testing and maintenance of the panel and all notification equipment
frequently as required.
• Check local, state and federal codes, regulations and laws, for required tests.
• Make sure that only qualified personnel perform all tests and maintenance.

7.2 Periodic Testing

7.2.1 Test Frequency

Perform mandatory testing of equipment at least twice each year, or more often as
required by local, state and federal codes, regulations, and laws.

7.2.2 Equipment
The following equipment needs to be tested to ensure that equipment is operating properly:
• SP40S Multi-Function Facility Communication System
• All notification appliances

7.3 Faulty Equipment

• If the notification equipment is not working properly, contact the service
representative and have problems corrected immediately.
• If the service representative is not available, contact the manufacturer.
• Replace any malfunctioning modules in the panel immediately. Do not attempt to
repair them.
• Return any malfunctioning modules to the manufacturer for repair or replacement.

7.4 Qualified Personnel

“Qualified personnel” are those who can evaluate proper equipment functionality and ensure
its proper operation and perform all testing procedures on the SP40S Multi-Function Facility
Communication System.
WARNING: PROVIDE ALTERNATIVE SIGNALING MEANS DURING PERIODIC
TESTING TO ASSURE ADEQUATE PROTECTION OF PEOPLE AND PROPERTY.
FAILURE TO PROVIDE ALTERNATIVE SIGNALING MAY CAUSE PEOPLE TO
NOT BE WARNED OF AN EMERGENCY CONDITION WHICH COULD RESULT IN
SERIOUS INJURY OR DEATH TO YOU AND/OR OTHERS.

SP40S Multi-Function Communications System 63

 Troubleshooting

8. Troubleshooting
8.1 Introduction

WARNING: SOME ELECTRONIC COMPONENTS STORE A HIGH VOLTAGE

CHARGE, EVEN THOUGH POWER IS NOT CONNECTED, AND CAN CAUSE A
DANGEROUS SHOCK IF TOUCHED. DO NOT TOUCH EXPOSED CIRCUITRY ON
THE SP40S MULTI-FUNCTION FACILITY COMMUNICATION SYSTEM UNLESS
THE CIRCUITRY HAS DISCHARGED FOR ONE HOUR AND A SAFE DISCHARGE
PROCEDURE IS USED.

WARNING: PROVIDE UL REQUIRED ALTERNATIVE SIGNALING MEANS

DURING TROUBLE CONDITIONS AND SERVICING TO ASSURE ADEQUATE
PROTECTION OF PEOPLE AND PROPERTY. ENSURE THAT QUALIFIED
SERVICE PERSONS IMMEDIATELY REPLACE ANY MODULES THAT HAVE
MALFUNCTIONED.

CAUTION: Make sure that only qualified personnel in accordance with the procedures
in this manual conduct troubleshooting and servicing. Do not attempt to make other
adjustments, modifications, or repairs. Never use water, steam, cleaning liquids or
sprays on the panel.

CAUTION: User servicing of the panel is limited to field-wiring changes, PC board

replacement, and following the instructions in the Installation chapter (Chapter 4) and
troubleshooting procedures in this chapter.

• After any troubleshooting procedure is completed, perform a complete system

checkout as described in Section 4.6.

8.2 General
The SP40S Multi-Function Facility Communication System monitors system integrity.
Items monitored for integrity are:
• Visual appliance circuit field wiring
• Audio appliance circuit field wiring
• Input voltage
• Battery voltage level
• Battery circuit field wiring
• Amplifier functionality
• Digital Voice Section functionality
• Battery charge voltage
• Tone generators
• Audio chain

SP40S Multi-Function Communications System 64

 Troubleshooting

System status is indicated to the visual indicators on the user interface, the internal Trouble
Sounder, and the Trouble and AC Trouble Form "C" relay contacts. If the AC (primary
power) is removed or low, the trouble the panel responds as follows:
• Turns "ON" the AC Trouble LED indicator on the user interface.
• Turns "ON" the System Trouble LED indicator on the user interface.
• Turns "ON" the internal sounder.
• Changes the state of the Form C AC Trouble contact to the TROUBLE position.
• Changes the state of the Form C General Trouble contact to the TROUBLE position.
(After 170 minutes if SW2-Position 2=ON or after 30 seconds if SW2-Position
2=OFF)
Any other trouble detected by the panel is reported as follows:
• Turns "ON" the System Trouble LED indicator on the user interface.
• Turns "ON" the internal sounder.
• Changes the state of the Form C General Trouble contact to the TROUBLE position.
When there are no trouble conditions detected, the user interface has the POWER ON
indicator illuminated while the SYSTEM TROUBLE and AC TROUBLE indicators are
OFF. If the POWER ON indicator is not illuminated, check to see if D100 and/or D109 (on
the PC board) are illuminated.
Figure 26 shows the location of all trouble location LED indicators within the SP40S. Table 7
cross-references the trouble location LED indicators on the PC board to the proper
troubleshooting procedure.
NOTE: When the System Trouble indicator is ON, indicating a panel Trouble, at least one
of the other yellow LED indicators is also ON, indicating the trouble location.

SP40S Multi-Function Communications System 65

 Troubleshooting

Table 7 Trouble Procedure Cross Reference

Troubleshooting
Condition Trouble Description
Procedure
D109 (POWER ON LED) is
AC and Battery power are missing or Low Section 8.2.1 (A)
OFF
D96 AND D97 are ON Strobe Over current Protection is active Section 8.2.2 (B)
D8 (BAT) is ON Battery voltage is below 20.4 VDC or battery is missing Section 8.2.3 (C)
AC TROUBLE (of display)
AC input voltage missing or low Section 8.2.4 (D)
is ON
D3 (DV) is ON Digital Voice Signal is too low or missing Section 8.2.5 (E)
D4 (MIC) is ON steady Push-to-Talk Microphone inoperable or missing Section 8.2.6 (F)
D5 (AMP) is ON steady Audio Over current Protection is active Section 8.2.7 (G)
D96 (STB SHT) is ON Strobe Notification Appliance Circuit is shorted Section 8.2.8 (H)
D97 (STB OPEN) is ON Strobe Notification Appliance Circuit is open Section 8.2.9 (I)
Auxiliary input is open, RMX is in trouble, or remote
D44 (AUX IN) is ON Section 8.2.10 (J)
MIC is in trouble
Audio Notification Appliance Circuit is Shorted, Splitter
D2 (AUD SHT) is ON Section 8.2.11(K)
is in trouble, or Audio Booster is in trouble
D1 (AUD OPEN) is ON Audio Notification Appliance Circuit is Open Section 8.2.12 (L)
D67 (GF) is ON Ground Fault Trouble Section 8.2.13 (M)
D47 (INT TRB) is ON User Interface is incorrectly connected or damaged Section 8.2.14 (N)
D6 (EXT AC WIR) is ON SPB SUP is open or Audio Booster has AC failure Section 8.2.15 (O)
D5 (AMP) is blinking Auxiliary preamp failure Section 8.2.16 (P)
D4 (MIC) is blinking Microphone preamp failure Section 8.2.17 (Q)
D93 (CHG TRB) is ON Battery voltage is below 18.5 VDC or battery is missing Section 8.2.18 (R)
D55 (DV1) is ON IN1 (DV input 1) is open Section 8.2.19 (S)
D62 (DV2) is ON IN2 (DV input 2) is open Section 8.2.19 (S)
D58 (DV3) is ON IN3 (DV input 3) is open Section 8.2.19 (S)
D65 (DV4) is ON IN4 (DV input 4) is open Section 8.2.19 (S)
D75 (DV5) is ON IN5 (DV input 5) is open Section 8.2.19 (S)
D84 (DV6) is ON IN6 (DV input 6) is open Section 8.2.19 (S)
D78 (DV7) is ON IN7 (DV input 7) is open Section 8.2.19 (S)
D87 (DV8) is ON IN8 (DV input 8) is open Section 8.2.19 (S)
EXCESSIVE NOISE FROM MOTHERBOARD MAY NOT BE PROPERLY
Section 8.2.20 (T)
SPEAKERS GROUNDED TO ENCLOSURE

Before performing any of the following troubleshooting procedures, make sure that
you read, understand, and follow the preliminary troubleshooting information at the
beginning of this “troubleshooting” chapter.

SP40S Multi-Function Communications System 66

 Troubleshooting

D4 MIC
PTT MIC Missing
D1 Audio Circuit or Inoperable
Open
D3 DV
Digital D5 AMP
Amplifier Section D6 SPB
D2 Audio Circuit Voice Section Supervision Open
Trouble
Short

D8 Batteries
Missing or Low

D29
(Red) Audio
Peak/Overload
D44 AUX IN,
CC Open,
RMX or
Remote MIC
Trouble

D47 Interface
Trouble
D55 - DV1 - IN1 OPEN
D62 - DV2 - IN2 OPEN

D58 - DV3 - IN3 OPEN

D65 - DV4 - IN4 OPEN
D67 GF
Ground
D75 - DV5 - IN5 OPEN
Fault
Trouble
D78 - DV7 - IN7 OPEN
D87 - DV8 - IN8 OPEN
D84 - DV6 - IN6 OPEN

D97 Strobe Open

D96 Strobe Circuit
F2 AC Short
Line Fuse D109 (Green)
(250V 10A) AC Power is Present

D93 Battery D100 (Green) F1 Battery Fuse

Charger Trouble Power is Present (125V 8A)
(AC or BAT)

Figure 26 Trouble LED and Fuse Locations

SP40S Multi-Function Communications System 67

 Troubleshooting

8.2.1 Procedure A
If the green PWR LED is “OFF” and all other LEDs are “OFF,” a power loss condition has
occurred. A power loss condition may be caused by:
• Loss of AC input voltage and battery back-up voltage.
• Faulty wiring of the AC power cord and batteries missing or low.
• Faulty motherboard.
Perform the following:
1. Check for AC voltage at TB9 on the motherboard. If voltage is not present, check for
AC input wiring. If AC voltage is present, check to see if fuse (F2) is blown. If F2 is
blown, replace the fuse (250V, 10A)
2. Check for at least 18.5 VDC at TB10 (Battery terminals). If sufficient voltage is
present, check to see if fuse (F1) is blown. If F1 is blown, replace the fuse (125V,
8A).
3. If the problem persists, replace the motherboard.
NOTE: Mark all wires before removing components. When the trouble is repaired, and
before testing, replace all wires to the proper locations and replace all covers.

8.2.2 Procedure B
If the green PWR LED is “ON,” the yellow SYSTEM TROUBLE LED is “ON,” and both
D96 and D97 are ON, the SP40S panel is in an Over current state.
• Check the strobe output for excessive current calculation. (2.0A for strobe circuit).
Perform the following:
1. If excessive current is calculated, remove appliances until the strobe current is below
2.0 Amps.
2. If excessive current does not exist, and strobe output is not operating, reset the
SP40S by removing AC and battery power.
3. Wait 30 seconds and reapply power. AC first and then batteries.

8.2.3 Procedure C
If the green PWR LED is “ON,” the yellow SYSTEM TROUBLE LED is “ON,” and D8,
BAT LED is “ON,” Battery Voltage is below 18.5 VDC or the battery is missing. A Battery
Trouble condition might be caused by:
• Batteries are missing.
• Battery wiring is incorrect.
• Batteries are defective.
• Battery charging section of the motherboard is inoperable.
Perform the following:
1. Check the battery compartment for the presence of batteries. If batteries are not
installed, install them.
2. Ensure that batteries are properly wired. See Figure 23 and Figure 24 for reference.

SP40S Multi-Function Communications System 68

 Troubleshooting

3. With the batteries NOT connected to the SP40S measure the series voltage of the
batteries. If the battery voltage is below 18.5VDC allow the SP40S more time to
charge the batteries.
4. With the batteries NOT connected, check for 24VDC at (+, -) BAT connection at
TB10 on the motherboard. If the voltage is below 18.5VDC, the battery charging
section of the motherboard is inoperable. Replace the motherboard.
5. If Steps 1 through 4 are satisfied, replace the batteries.
NOTE: The Batteries could take up to 24 hours to charge to capacity.

8.2.4 Procedure D
If the green PWR LED is “ON,” the yellow SYSTEM TROUBLE LED is “ON,” the AC
TROUBLE LED is “ON,” and the D93 CHG TRB LED is “ON” the AC is low or missing.
An AC Trouble condition might be caused by:
• AC input missing or low.
• AC fuse (F2) is blown.
• A faulty motherboard.
Perform the following:
1. Check fuse F2 on the motherboard. Replace if necessary (250V, 10A).
2. Check for AC voltage at TB9
- If voltage is not present, check the wiring and circuit breaker.
- If voltage is present AND fuse F2 is not open, replace the motherboard.

8.2.5 Procedure E
If the green PWR LED is “ON,” the yellow SYSTEM TROUBLE LED is “ON,” D3 DV
LED is “ON,” the Digital Voice messages are missing or the DV output voltage is too low.
A DV Low Output Voltage condition might be caused by:
• Missing or incorrectly installed memory chip.
• Digital Voice volume control (R73) set too low.
• No messages recorded on memory chip.
Perform the following:
1. Check memory chip (U31) to ensure it is installed properly.
2. Verify that messages are recorded on the chip by activating them using the display
buttons.
3. Check Digital Voice volume control (R73) for proper volume level.
4. If messages were field recorded, make sure the message(s) were recorded properly
and at the proper volume.
5. Replace the motherboard.

SP40S Multi-Function Communications System 69

 Troubleshooting

8.2.6 Procedure F
If the green PWR LED is “ON,” the yellow SYSTEM TROUBLE LED is “ON,”D4 MIC
LED is “ON” steadily, the push-to-talk microphone is missing, improperly plugged in, or
defective.
Perform the following:
1. Install the microphone.
2. Remove the microphone plug and plug it back in.
3. Replace the microphone.
4. Replace the motherboard.

8.2.7 Procedure G
An Amplifier Trouble is present, if the green PWR LED is “ON,” the yellow SYSTEM
TROUBLE LED is “ON,” and D5 AMP LED is “ON” steady. An Amplifier Trouble
condition may be caused by:
• Short on the audio output.
• Overloaded audio output.
• Over current circuit protection mode from improper power up.
Perform the following:
1. Check the TB4, Audio Out terminals and speaker wiring for shorts.
2. Check to ensure the speakers are tapped correctly.
3. Check to ensure the Output Select jumper (J1) is installed at the proper voltage
level.
4. Reset the SP40S by removing AC and Battery power. Wait 30 seconds and
reapply power. AC first and then batteries.
5. Replace the motherboard.

8.2.8 Procedure H
If the green PWR LED is “ON,” the yellow SYSTEM TROUBLE LED is “ON,” and D96,
STB SHORT LED is “ON,” a short condition exists on the STB OUT NAC output circuit.
A STB SHORT trouble condition might be caused by:
• Shorted appliance on STB OUT (TB12).
• Faulty wiring between STB OUT and strobe notification appliance circuit is causing
a short.

Perform the following: Check the wiring and strobe notification appliances for a short circuit
condition.

SP40S Multi-Function Communications System 70

 Troubleshooting

8.2.9 Procedure I
If the green PWR LED is “ON,” the yellow SYSTEM TROUBLE LED is “ON,” and D97
STB OPEN LED is “ON,” an open condition exists on the STB OUT NAC output circuit. A
STB OPEN trouble condition might be caused by:
• Missing UL Listed 10K OHM, ½ W EOLR on the STB OUT circuit (TB12).
• Faulty wiring causing an open on the Strobe Notification Appliance Circuit.

Perform the following:

1. Check for proper EOLR.

2. Check the strobe notification appliance circuit wiring for an open condition.

8.2.10 Procedure J
If the green PWR LED is “ON,” the yellow SYSTEM TROUBLE LED is “ON,” and D44
AUX IN LED is “ON,” an open condition exists on the CC/NAC input circuit. An AUX IN
trouble condition might be caused by:
• A Remote Microphone or RMX trouble being reported to the SP40S panel (if a
remote MIC or RMX is connected).
• Faulty wiring is causing an open on the CC/NAC input circuit (TB6).
• Jumper JP2 being removed and missing a UL Listed 10K Ohm, ½ W EOLR on the
CC/NAC circuit (TB6) (if a remote MIC is not connected).
Perform the following:
1. Check the Remote Microphone and/or RMX wiring for an open condition.
2. Check the jumper setting (JP4) if a Remote Microphone or RMX is not
connected to the SP40S panel.
3. If the Remote Microphone or RMX is in a trouble condition, refer to that
installation manual to troubleshoot that particular product.

8.2.11 Procedure K
If the green PWR LED is “ON,” the yellow SYSTEM TROUBLE LED is “ON,” and D2,
AUDIO SHORT LED is “ON,” a short condition exists on the AUDIO OUT circuit. An
AUDIO SHORT trouble condition might be caused by:
• Shorted speaker appliance on AUDIO OUT (TB4).
• Faulty wiring between AUDIO OUT and Speaker Notification Appliance Circuit is
causing a short.
• A trouble being reported from an Audio Splitter or Audio Booster.
Perform the following:
• Check the wiring and Audio Notification Appliances for a short circuit condition.
• If a Splitter or Audio Booster is in a trouble condition, refer to that manual to
troubleshoot that particular product.

SP40S Multi-Function Communications System 71

 Troubleshooting

8.2.12 Procedure L
If the green PWR LED is “ON,” the yellow SYSTEM TROUBLE LED is “ON,” and D1
AUDIO OPEN LED is “ON,” an open condition exists on the STB OUT NAC output
circuit. A STB OPEN trouble condition might be caused by:
• Missing UL Listed 10K OHM, ½ W EOLR on the AUDIO OUT circuit (TB4).
• Faulty wiring is causing an open on the speaker notification appliance circuit.
Perform the following:
1. Check for proper EOLR.
2. Check the speaker notification appliance circuit wiring for an open condition.

8.2.13 Procedure M
If the green PWR LED is “ON,” the yellow SYSTEM TROUBLE LED is “ON,” and D67
GF LED is “ON,” a ground fault condition exists on the output wiring. A GF trouble
condition might be caused by:
• Appliance wiring touching conduit.
• Improper Installation of an appliance(s).
Perform the following:
1. Disconnect appliances from the strobe (TB12) and speaker (TB4) connection on
the motherboard.
2. Troubleshoot the NAC circuits by checking for a resistance reading other than
infinity between the appliance leads and the conduit.

8.2.14 Procedure N
If the green PWR LED is "ON," the yellow SYSTEM TROUBLE LED is "ON," and D47
INT TRB is "ON," an Interface Trouble exists. An Interface trouble might be caused by:
• The 30 pin ribbon cable being removed from the display or motherboard
• The 30 pin ribbon cable being connected to the wrong header.
• The 30 pin ribbon cable being damaged.
Perform the following:
1. Ensure that the ribbon cable is properly installed to the user interface and to the
motherboard at J6 (Display Interface).
2. Check to see if the ribbon cable has been damaged in any way. If the ribbon
cable is damaged, replace it.

SP40S Multi-Function Communications System 72

 Troubleshooting

8.2.15 Procedure O
If the green PWR LED is "ON," the yellow SYSTEM TROUBLE LED is "ON," and D6
EXT AC WIR is "ON," an open condition exists on the SPB SUP terminals (TB4). This
trouble can be caused by:
• Switch SW2 position 1 is ON despite the SPB SUP terminals not being used.
• UL Listed 10k OHM ½ W EOLR not detected by the SUB SUP terminals.
Perform the following:
1. If AC is being reported separately from the Audio Booster, make sure that a 10k
Ohm ½ W EOLR is properly installed at the Audio Booster and the Audio
Booster is operating properly.
2. If AC is NOT being reported separately, make sure there is nothing on the SPB
SUP terminals (TB4) AND Switch SW2 - position 1 (SPB SUP) is OFF.

8.2.16 Procedure P
If the green PWR LED is "ON," the yellow SYSTEM TROUBLE LED is "ON," and D5
AMP LED is blinking, an Auxiliary preamp trouble has occurred.
Perform the following:
1. Turn Aux Volume Pot (R100) fully clockwise.
2. Initiate the AUX input if it is being used (via Remote MIC).
3. Reset power to the SP40S board by turning it OFF and reenergizing it. Remove
battery power first, then remove AC power. Wait 30 seconds. Apply AC Power
first, then apply battery power.
4. Replace the motherboard.

8.2.17 Procedure Q
If the green PWR LED is "ON," the yellow SYSTEM TROUBLE LED is "ON," and D4
MIC LED is blinking, a Mic preamp trouble has occurred.
Perform the following:
1. Initiate the MIC input to verify its functionality.
2. Reset power to the SP40S board by turning it OFF and reenergizing it. Remove
battery power first, then remove AC power. Wait 30 seconds. Apply AC Power
first, then apply battery power.
3. Replace the motherboard.

SP40S Multi-Function Communications System 73

 Troubleshooting

8.2.18 Procedure R
If the green PWR LED is "ON," the yellow SYSTEM TROUBLE LED is "ON," and D93
BATT CHG TRB LED is "ON," a battery charger trouble has occurred.
NOTE: The CHG TRB LED turns ON during an AC TROUBLE. Restoring the AC Voltage
turns OFF the CHG TRB LED.
Perform the following:
1. Remove batteries and measure the voltage at the battery terminals (TB10). If
voltage is present, above 20 Volts there is no problem with the battery charger.
2. If there is no voltage at the battery terminals (TB10) while the SP40S is running
on AC power, then there is a problem with the battery charger. Replace the
motherboard.

8.2.19 Procedure S
If the green PWR LED is "ON," the yellow SYSTEM TROUBLE LED is "ON," and one of
the IN# LEDs (D55, D58, D62, D65, D75, D78, D84, or D87) are "ON," a DV Contact
Closure Wiring Trouble exists.
Perform the following:

1. If a particular Contact Closure is not being used, make sure nothing is on the
corresponding terminal block (TB7 or TB8) and the corresponding IN CC
Supervision is turned OFF at switch SW7.
2. If a particular Contact Closure is being used, make sure that a UL approved 10k
Ohm ½ W EOLR is installed on the proper terminals.

8.2.20 Procedure T
If the unit is in normal standby mode yet excessive noise is being heard from the speakers,
the unit may not be properly grounded to the enclosure.
Perform the following:

1. Verify that the 4 metal standoffs are installed and securely fastened. Refer to
figure 3-9 for location of the grounding standoffs.
2. Verify that the 4 screws are installed and securely fastened. Refer to figure 3-9
for location of the grounding screws.

SP40S Multi-Function Communications System 74

 Technical Data

9. Technical Data
9.1 Mechanical
Parameter Description
Dimensions (H x W X D) 21 x 16 x 6 inches
Weight 36 lb
Finish Red or Black
Enclosure Enclosure Door: 16 Gauge (.060) CRS
Construction Type Enclosure Backbox: 16 Gauge (.060) CRS
Mounting Indoor surface mount
Wiring Top, left, right, and bottom knockouts (3/4”-1”) (18 total)
Entry Top (2” - 2 ½” - 3”) (2 total)
Door Lock Standard Cooper Notification key-lock
1 Motherboard
PC Boards
1Keypad board

9.2 Environmental
Parameter Description
Operating Temperature 0 to 49 °C (32 to 120 °F)
Storage Temperature -20 to 70 °C (-4 to 158 °F)
Humidity, Non-condensing 93% at 30 ± 2 °C (86 ± 4 °F)

9.3 Electrical

9.3.1 Input
Parameter Description
Primary Input Voltage SP40S 120VAC, 2.4A, 60Hz
Primary Input Voltage SP40SE 240VAC, 1.5A, 50/60Hz
Secondary (Battery) Voltage 20.4-27.5VDC (33Ah)

9.3.2 Battery Current Calculations

The current draw of the SP40S Multi-Function Facility Communication System is
determined by the configuration being used. Section 4.8, Battery Care and Battery Backup
Calculation, will assist you in developing the current requirements.

9.3.3 Activation
There are nine ways to activate the SP40S panel. The table below lists these activation
sources in order of priority.

SP40S Multi-Function Communications System 75

 Technical Data

Method of Activation Description

Strobe NAC 8-33VDC
Push-to-Talk Microphone Connected to Mother Board
Auxiliary Input Remote Microphone or RMX Initiation. 825 Ohms at 1V.
IN1 Contact Closure. Activates Message 1 on Digital Voice Section.
IN2 Contact Closure. Activates Message 2 on Digital Voice Section.
IN3 Contact Closure. Activates Message 3 on Digital Voice Section.
IN4 Contact Closure. Activates Message 4 on Digital Voice Section.
IN5 Contact Closure. Activates Message 5 on Digital Voice Section.
IN6 Contact Closure. Activates Message 6 on Digital Voice Section.
IN7 Contact Closure. Activates Message 7 on Digital Voice Section.
IN8 Contact Closure. Activates Message 8 on Digital Voice Section.
Telephone Page Telephone Page Port
Night Ring Contact Closure
Background Music Line Level Signal 2.5V P-P or 300mV RMS at 600 Ohms.

9.3.4 Outputs

Parameter Description
Visual Notification Appliance Output 1 output circuit. 2.0 amps at 24VDC. Supervised.
1 output circuit.
Selectable 25 or 70.7 Volt RMS output at 40W max.
Central Amplified Audio Output Supervised.
25V setting = Class 2
70V setting = Class 3
Form C contact normally energized. Contacts transfer
Trouble Contact during trouble: 2.0 amps at 24VDC max, resistive load
(see following warning). Non-Supervised.
Form C contact normally energized. Contacts transfer
Alarm Contact during alarm trouble: 2.0 amps at 24VDC max, resistive
load (see following warning). Non-Supervised.
Form C contact normally energized. Contacts transfer
AC Trouble Contact during AC trouble: 2.0 amps at 24VDC max, resistive load
(see following warning). Non-Supervised.

WARNING: DO NOT EXCEED THE RATINGS OF THE STATUS CONTACTS.

EXCEEDING THIS RATING MAY CAUSE THE RELAY TO FAIL AND PREVENT A
TROUBLE CONDITION FROM BEING INDICATED.

SP40S Multi-Function Communications System 76

 Technical Data

WARNING: DO NOT EXCEED THE RATINGS OF THE ALARM CONTACTS.

EXCEEDING THIS RATING MAY CAUSE THE RELAY TO FAIL AND PREVENT
THE MESSAGES FROM BEING PLAYED.

9.4 Wiring Connections

Parameter Description
Accepts #12 to #18 AWG for single wire
Screw terminals connection, or #16 to #18 AWG for double wire
connection.

9.4.1 End of Line Resistor (EOLR)

Parameter Description
Accepts #12 to #18 AWG for single wire
Screw terminals connection, or #16 to #18 AWG for double wire
connection.

SP40S Multi-Function Communications System 77

 Warranty

10. Warranty
LIMITED WARRANTY
Cooper Wheelock, Inc. dba Cooper Notification and Cooper Notification, Inc. (each, a “Seller”) products must be used within
their published specifications and must be PROPERLY specified, applied, installed, operated, maintained and operationally
tested in accordance with these instructions at the time of installation and at least twice a year or more often and in
accordance with local, state and federal codes, regulations and laws. Specification, application, installation, operation,
maintenance and testing must be performed by qualified personnel for proper operation in accordance with all of the latest
National Fire Protection Association (NFPA), Underwriter’s Laboratories (UL), National Electrical Code (NEC), Occupational
Safety and Health Administration (OSHA), local, state, county, province, district, federal and other applicable building and fire
standards, guidelines, regulations laws and codes including, but not limited to, all appendices and amendments and the
requirements of the local authority having jurisdiction (AHJ). Seller products when properly specified, applied, installed,
operated, maintained and operationally tested as provided above are warranted against mechanical and electrical defects for
a period of (a) three (3) years from date of manufacture with respect to MEDC and Seller Industrial Signals and Seller Fire
and Security Notification Appliances and Devices, or (b) one (1) year from date of manufacture with respect to Waves and
SafePath Voice Evacuation and Mass Notification Systems (date of manufacture is determined by date code.) Correction of
defects by repair or replacement shall be at Seller’s sole discretion and shall constitute fulfillment of all obligations under this
warranty. THE FOREGOING LIMITED WARRANTY SHALL IMMEDIATELY TERMINATE IN THE EVENT ANY PART NOT
FURNISHED BY SELLER IS INSTALLED IN THE PRODUCT. THE FOREGOING LIMITED WARRANTY SPECIFICALLY
EXCLUDES ANY SOFTWARE REQUIRED FOR THE OPERATION OF OR INCLUDED IN A PRODUCT. SELLER MAKES
NO REPRESENTATION OR WARRANTY OF ANY OTHER KIND, EXPRESS, IMPLIED OR STATUTORY WHETHER AS TO
MECHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER MATTER.

USERS ARE SOLELY RESPONSIBLE FOR DETERMINING WHETHER A PRODUCT IS SUITABLE FOR THE USER’S
PURPOSES, OR WHETHER IT WILL ACHIEVE THE USER’S INTENDED RESULTS. THERE IS NO WARRANTY AGAINST
DAMAGE RESULTING FROM MISAPPLIACATION, IMPROPER SPECIFICATION, ABUSE, ACCIDENT OR OTHER
OPERATING CONDITIONS BEYOND SELLER’S CONTROL.

SELLER DOES NOT WARRANT THAT THE OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-
FREE OR THAT THE SOFTWARE WILL MEET ANY OTHER STANDARD OF PERFORMANCE, OR THAT THE
FUNCTIONS OR PERFORMANCE OF THE SOFTWARE WILL MEET THE USER’S REQUIREMENTS. SELLER SHALL
NOT BE LIABLE FOR ANY DELAYS, BREAKDOWNS, INTERRUPTIONS, LOSS, DESTRUCTION, ALTERATION, OR
OTHER PROBLEMS IN THE USE OF A PRODUCT ARISING OUT OF OR CAUSED BY THE SOFTWARE.

THE LIABILITY OF SELLER ARISING OUT OF THE SUPPLYING OF A PRODUCT, OR ITS USE, WHETHER ON
WARRANTIES, NEGLIGENCE, OR OTHERWISE, SHALL NOT IN ANY CASE EXCEED THE COST OF CORRECTING
DEFECTS AS STATED IN THE LIMITED WARRANTY AND UPON EXPIRATION OF THE WARRANTY PERIOD ALL SUCH
LIABILITY SHALL TERMINATE. SELLER IS NOT LIABLE FOR LABOR COSTS INCURRED IN REMOVAL,
REINSTALLATION OR REPAIR OF A PRODUCT BY ANYONE OTHER THAN SELLER OR FOR DAMAGE OF ANY TYPE
WHATSOEVER, INCLUDING BUT NOT LIMITED TO, LOSS OF PROFIT OR INCIDENTAL, INDIRECT, CONSEQUENTIAL,
SPECIAL, PUNTIVE OR EXEMPLARY DAMAGES. THE FOREGOING SHALL CONSTITUTE THE SOLE REMEDY OF THE
PURCHASER AND THE EXCLUSIVE LIABILITY OF SELLER.

IN NO CASE WILL SELLER’S LIABILITY EXCEED THE PURCHASE PRICE PAID FOR A PRODUCT.

LIMITATION OF LIABILITY
SELLER’S LIABILITY ON ANY CLAIM OF ANY KIND, INCLUDING NEGLIGENCE AND BREACH OF WARRNTY, FOR ANY
LOSS OR DAMAGE RESULTING FROM, ARISING OUT OF, OR CONNECTED WITH THIS CONTRACT, OR FROM THE
MANUFACTURE, SALE, DELIVERY, RESALE, REPAIR OR USE OF ANY PRODUCT COVERED BY THIS ORDER SHALL
BE LIMITED TO THE PRICE APPLICABLE TO THE PRODUCT OR PART THEREOF WHICH GIVES RISE TO THE CLAIM.
SELLER’S LIABILITY ON ANY CLAIM OF ANY KIND SHALL CEASE IMMEDIATELY UPON THE INSTALLATION IN THE
PRODUCT OF ANY PART NOT FURNISHED BY SELLER. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY CLAIM
OF ANY KIND UNLESS IT IS PROVEN THAT ITS PRODUCT WAS THE DIRECT CAUSE OF SUCH CLAIM. FURTHER, IN
NO EVENT, INCLUDING IN THE CASE OF A CLAIM OF NEGLIGENCE, SHALL SELLER BE LIABLE FOR INCIDENTAL,
INDIRECT, CONSEQUENTIAL, SPECIAL, PUNITIVE OR EXEMPLARY DAMAGES. SOME STATES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE PRECEDING LIMITATION
MAY NOT APPLY TO ALL PURCHASERS.

SP40S Multi-Function Communications System 78

 Battery Backup Calculation Worksheet

11. Battery Backup Calculation Worksheet

SP40S BATTERY CALCULATION SHEET
STANDBY CURRENT CALCULATIONS
1. The Standby Current for the SP40S is 0.130 Amps. ______________ Amps
2. Enter Auxiliary Current (If Applicable) ______________ Amps
3. Add Steps 1 and 2. Multiply by the number of hours required.
24 Hours – Multiply by 24 ______________ Hrs

TOTAL STANDBY CAPACITY IN AMP HOURS ______________ Ah

ALARM CURRENT CALCULATIONS NOTE: DO NOT EXCEED 40 WATTS.

Good engineering practices call for amplifier to operate at 85% Max wattage.
1. List the speaker and strobe requirements.
NOTIFICATION SPEAKER STROBE
APPLIANCE WATTAGE CURRENT

2. Calculate total Strobe current. (2. Amps Max.) ______________ Amps

3. Calculate total speaker wattage. (40 Watts Max.) ______________ Watts
4. Multiply the total speaker wattage on line 3 by 0.054. ______________ Amps
5 Add Auxiliary Current (if applicable) ______________ Amps
6. Add Steps 2,4 and 5 together. (4.66 Amps Max.) ______________ Amps
7. Multiply Step 6 by 0.25 (This represents 15 minutes of alarm.) ______________ Hrs
8 Total Alarm Capacity in Amps-Hours. ______________ Ah
BACKUP BATTERY REQUIREMENTS
1. Enter Standby Capacity. ______________ Ah
2. Enter Alarm Capacity. ______________ Ah
3. Add Steps 1 and 2 together. ______________ Ah
Multiply Step 3 by 1.1 for minimum Backup Battery Requirements ______________ Ah

SP40S Multi-Function Communications System 79

 Compatible Signaling Appliances

12. Compatible Signaling Appliances

The following Cooper Notification products are LISTED compatible with the audio
notification appliance output and the visual notification output circuits for the SP40S Panel.
When connected to the SPB-80/4, strobe synchronization is system-wide. All strobe
products can be fully synchronized.
Strobes

RSS-24MCW RSS-24MCC LST3/LSTC3

RSS-24MCWH RSS-24MCCH LST/LSTC
RSSP-24MCW RSS-24MCCHR ST/ST-C
RSSP-24MCWH RSS-241575W DC-MAXS
ZRS-MCW RSSP-241575W
ZRS-MCWH RSSWP-2475W

Speaker/Strobe Combination

ET-1080-IS-24 ET70-24MCW LSPST3/LSPSTC3

ET-1080-LS-24 ET70-24MCWH LSPST/LSPSTC
ET-1080-LSM-24 ET70-241575W SA-S70-24MCW
ET-1080-MS-24 E70-24MCW S8-25/70MCC
ET-1080-SLM-24 E70-24MCCWH S8-25/70MCCH
E50-24MCW E70-241575W STH-2MSR
E50-24MCWH E70H-241575W STH-3MSR
E50-241575W E70H-MCW STH-4MSR
E50H-241575W E70H-24MCWH STH-2R24MCCH
E50H-MCW ET80-24MCW STH-3R24MCCH
E50H-24MCWH ET80-24MCWH STH-4R24MCCH
E60-24MCC ET80-241575W STH-4M30WC
E60-24MCCH E90-24MCC STH-90-R24MCCH
E60-24MCW E90-24MCCH
E60-24MCWH ET90-24MCC
E60-241575W ET90-24MCCH
E60H-24MCC E90H-24MCC
E60H-24MCCH E90H-24MCCH
Horns Horn/Strobe Combination
HN/HN-C HS/HS-C
LHN/LHNC/LHN3/LHNC3 LHS/LHSC/LHS3/LHSC3
LLFHN/LFHNK3 LLFHS/LFHSK3

The following Wheelock products are LISTED compatible with the trouble audible output.

Bells
MB-G6-24
MB-G10-24

SP40S Multi-Function Communications System 80

 Compatible Signaling Appliances

The following devices are rated per UL 2017 and UL 864 for use with the SP40S for the NFPA 72
low frequency tone sleeping area application

Speakers Speaker/Strobes
E50H E50H-241575W E50H-24MCW
E60H E50H-24MCWH E60H-24MCC
E70H E60H-24MCCH E70H-241575W
E90H E70H-24MCW E70H-24MCWH
S8-70/25 E90H-24MCC E90H-24MCCH
LSPK S8-24MCC S8-24MCCH
LSPKC LSPST3 LSPSTC3
LSPST LSPSTC

Amplifiers Accessories
SPB-80/4 SP4Z-A/B
SPB-80/4E SP4-APS
SPB-160 SP-SVC
SPB-160E
SPB-320
SPB-320E

SP40S Multi-Function Communications System 81

 Compatible Signaling Appliances

This page left intentionally blank.

SP40S Multi-Function Communications System 82