SECTION-V PUMPS & ELECTRO MECHANICAL WORKS PUMPS & MOTORS

Annexure – I

TECHNICAL DATA SHEET

Sl. No. Parameter UOM Value

PUMP PERFORMANCE

1 Manufacturer -

2 Type of Pump -

3 Model -

4 Rated Discharge m3/hr

5 Rated Head m

6 Pump Efficiency at Duty Point %

7 Overall Efficiency at Duty Point %

8 BkW kW

9 Shut-off Head m

10 Maximum Discharge m3/hr

11 Head at Maximum Discharge m

12 Maximum Input to the Pump over Entire Operating Range kW

13 Pump Input at Shut-off kW

14 Pump Input at Maximum Discharge kW

15 NPSHR at Duty Point m

16 NPSHR at Maximum Discharge

17 Minimum Submergence required for Safe Operation mm

o
18 Maximum permissible Liquid temperature C

19 Speed rpm

20 No. of stages -

21 Max out side dia. Of bowl mm

CONTRACTOR 16/53 SUPERINTENDING ENGINEER

SECTION-V PUMPS & ELECTRO MECHANICAL WORKS PUMPS & MOTORS

Annexure II

OFFERED BY
Sl. No. Parameter
BIDDER

MATERIAL OF CONSTRUCTION

1 Pump Casing

2 Impeller

3 Gland packing

4 Shaft

5 Motor casing

6 Column pipe

7 Discharge Elbow

8 Line shaft bearing

9 Shaft protection tube

10 Fasteners

11 Foundation / Grouting Fasteners

CONSTRUCTION OF PUMPSET

12 Type of Pump Casing

13 Type of Impeller

14 Type of Thrust Bearing

15 Installation Arrangement -Delivery nozzle above pump floor

16 Seal Arrangement

17 Motor Cooling Arrangement

18 Type of lubrication for thrust bearing

19 Type of lubrication for shaft bearing

Note : Lubrication for line shaft bearing is external forced water lubrication which is mandatory
for all the pumps.
CONTRACTOR 17/53 SUPERINTENDING ENGINEER
SECTION-V PUMPS & ELECTRO MECHANICAL WORKS PUMPS & MOTORS

Annexure – III

DECLARATION ON THE PRODUCT OFFERED

Sl. Declaration
Description Remarks
No. Yes No

1 Pump manufacturer.

2 Impeller balanced dynamically

3 Sealing with gland packing

4 Line shaft lubrication Arrangement / Design as

per Specifications

5 Interlocks for lubrication system provided.

6 Cooling of the Thrust bearing provided .

7 Wearing ring provided for impeller

8 Bearings are provided as per specifications .

9 Installation accessories exactly as per

specifications

10 Motor is Squirrel Cage induction type HT/LT

as per specs

11 Temperature sensor for COOLING WATER

OUTLET OF THRUST BEARING LOCATED IN
PUMP

12 Gland Leakage out let piping provided

13 All the performance characteristics as per

clause enclosed.

14 Testing Facility at Rated Voltage, rated

Frequency and rated speed available at
manufacturer’s work.

15 All motors can be tested for Routine and Type

tests at manufacturer’s works.

CONTRACTOR 18/53 SUPERINTENDING ENGINEER

SECTION- PUMPS & ELECTRO MECHANICAL PUMPS &
V WORKS MOTORS

Technical Data Sheet of Submerged Centrifugal

Pump sets
(To be s u b m i t t e d a l o n g w i t h t h e b i d d o c u m e n t s )

Sl. No Description Particular

s
1 Make of Pump set
2 Model
3 Design Capacity m3/hr
4 Total Head Mwc
5 Shut Off Head

6 Rated Speed & Supply

Frequency
7 No of Stages

8 No of Casing
9 Pump Efficiency @ duty point
10 bkW @ duty point

11 Maximum Pump
Input throughout the
12 Rated Motor Efficiency
Over All Pump set Efficiency @
13
duty point
14 Motor Input @ Duty Point
15 Motor Rating kW

16 Class of Insulation of Motor

17 Fill of Motor Air / Oil / Water

Type of Bearings & its rated L10
18 life
Type of Lubrication & its rated
19
Life

CONTRACTOR 27/53 SUPERINTENDING

ENGINEER
SECTION- PUMPS & ELECTRO MECHANICAL PUMPS &
V WORKS MOTORS

mm2 x _Cores x
Runs
Power
Cables
mm2 x Cores x

Control mm2 x Cores x

20 Cable Size & MoC Cables Runs
Conduc Al / Cu
t or
Pump’s Suction & Delivery
21 Nozzle size mm & mm

22 Suction Strainer Provided Yes / No

23 MoC of Motor Rotor Shaft

24 MoC of Pump Casing

25 MoC of Impeller

26 MoC of Impeller’s Wearing Ring

27 MoC of Casing’s Wearing Ring

28 Weight of Pump set Kg

CONTRACTOR 28/53 SUPERINTENDING ENGINEER

 SECTION – V PUMPS & ELECTRO – MECHANICAL WORKS ELECTRO-MECHANICAL WORK

9.16 Data Sheets to be filled by Contractor – Electrical

9.16.1 Technical Particulars
The contractor shall complete the various tables given under this schedule to give the technical
particulars of the equipment proposed by him.

If any additional particulars are necessary or the particulars are given in some other form the same
may be enclosed separately.

The contractor shall give all the particulars. The tender, may be considered as non-responsive, if
important particulars are not submitted.

9.16.2 HT Switchgear
1 General Particulars
a) Name of Panel manufacturer
b) Construction compartmentalised or
non-compartmentalised
c) Sheet metal thickness
d) Degree of protection

2 Dimensions of the Board Length (mm) x Width

(mm) x Depth (mm)

3 I) Material of busbars
ii) Busbar size
Phase
Neutral

iii)Ground Bus (Material & size)

4 Vacuum Circuit Breaker

a) Make
b) Type

5 Protection relays
a) Make
b) Type

6 Control Wiring
a) Size
b) Type
c) Insulation
d) Voltage grade

7 Control Terminals
a) Make
b) Type
c) Voltage Grade

CONTRACTOR 89/97 SUPERINTENDINGENGINEER

 SECTION – V PUMPS & ELECTRO – MECHANICAL WORKS ELECTRO-MECHANICAL WORK

d) Current rating
e) Minimum 10 % spare terminal furnished

8 Push Buttons
a) Make
b) Type
c) No. & Rating of Contacts

9 Indicating Lamps
a) Make
b) Type
c) Rating

10 Integrating Meters
a) Make
b) Type
c) Accuracy Class
d) VA Burden

11 Current Transformers
a) Make
b) Type
c) Core Details (Current ratio, VA Burden,
Accuracy, RCT and VK)
Core 1:
Core 2:

Core 3:

12 Potential Transformers
a) Make
b) Type
c) Core Details (Voltage ratio, VA Burden, and
Accuracy)
Core 1:
Core 2:

13 Terminal Blocks
a) Make
b) Type
c) Current rating
d) Voltage Grade
e) Suitable for 2 Nos. Cu 2.5.mm2 wire

14 H.T. Capacitors
a) Make
b) Type

CONTRACTOR 90/97 SUPERINTENDINGENGINEER

 SECTION – V PUMPS & ELECTRO – MECHANICAL WORKS ELECTRO-MECHANICAL WORK

c) kVAR Rating/Unit x No. of Units

9.16.3 Soft Starter

1 General Particulars
a) Name of Panel manufacturer
b) Sheet metal thickness
c) Degree of protection

2 Dimensions of the Board Length (mm) x Width

(mm) x Depth (mm)

3 I) Material of busbars
ii) Busbar size
Phase
Neutral

iii)Ground Bus (Material & size)

4 Bypass contactor / breaker

a) Make
b) Type

c) rating

5 Protection relays
a) Make
b) Type

6 Control Wiring
a) Size
b) Type
c) Insulation
d) Voltage grade

7 Control Terminals
a) Make
b) Type
c) Voltage Grade
d) Current rating
e) Minimum 10 % spare terminal furnished

8 Push Buttons
a) Make
b) Type
c) No. & Rating of Contacts

9 Indicating Lamps
a) Make
CONTRACTOR 91/97 SUPERINTENDINGENGINEER
 SECTION – V PUMPS & ELECTRO – MECHANICAL WORKS ELECTRO-MECHANICAL WORK

b) Type
c) Rating

10 Integrating Meters
a) Make
b) Type
c) Accuracy Class
d) VA Burden

11 Current Transformers
a) Make
b) Type
c) Core Details (Current ratio, VA Burden,
Accuracy, RCT and VK)
Core 1:
Core 2:

Core 3:

12 Potential Transformers
a) Make
b) Type
c) Core Details (Voltage ratio, VA Burden, and
Accuracy)
Core 1:
Core 2:

13 Terminal Blocks
a) Make
b) Type
c) Current rating
d) Voltage Grade
e) Suitable for 2 Nos. Cu 2.5.mm2 wire

9.16.4 L.T. Switchgear

1 General Particulars

Name of Manufacturer

Sheet metal thickness

2 Air Circuit Breaker

a) Make

b) Type

3 Moulded case Circuit Breaker

CONTRACTOR 92/97 SUPERINTENDINGENGINEER

 SECTION – V PUMPS & ELECTRO – MECHANICAL WORKS ELECTRO-MECHANICAL WORK

a) Make

b) Type

4 Selector Switch

a) Make

b) Type

5 Push Buttons

a) Make

b) Type

6 Indicating Lamps

a) Make

b) Type

7 Integrating Meters

a) Make

b) Type

8 Current Transformers

a) Make

b) Type

9 L.T. Capacitors

a) Make

b) Type

9.16.5 Battery
1 Battery Capacity at 27° C at 10 hour rate

Initial

Rated

End of life

2 Type of positive plates

CONTRACTOR 93/97 SUPERINTENDINGENGINEER

 SECTION – V PUMPS & ELECTRO – MECHANICAL WORKS ELECTRO-MECHANICAL WORK

3 No. of positive plates/cell

4 No. of cells required to give rated D.C. voltage

No. of spare cells

5 Expected life of battery

9.16.6 Battery Charger cum DCDB

1 Manufacturer's Name

2 Type - Float Charger/Boost Charger/Float cum

boost charger

3 Rating

i) Input voltage

ii) Output voltage

iii) Rated output

9.16.7 L.T. Cables

Name of Manufacturer

1. LT Power cable

2. Control / Lighting cable

9.16.8 H.T. Cables

1. Name of Manufacturer

2. Type

3. No. of cores

4. Size

9.16.9 Miscellaneous
1 Cable glands make and type

2 Cable Lugs make and type

3 Type of wires lighting

Make
Voltage grade

4 Outdoor Cabling:-
Cable route marker RCC block type prov. Yes/No
Cable protection covers RCC tiles prov. Yes/No

CONTRACTOR 94/97 SUPERINTENDINGENGINEER

 SECTION – V PUMPS & ELECTRO – MECHANICAL WORKS ELECTRO-MECHANICAL WORK

5 Lighting Fixture – Makes

6 ACSR conductor size

7 Clamp for ACSR conductor –

a) make

b) type

9.17 LIST OF ELECTRIACAL DRAWINGS

9.17.1 HT Capacitors
Drawing and documents required
• GA drawing of the capacitor unit, bank

• Instruction manual for installation, operation and maintenance for capacitor

9.17.2 6.6 kV Indoor Switchgear

Drawing and documents required
• GA drawing of 33 kV panel with foundation details

• Single line diagram for HV panels

• Schematic diagrams for various modules

• Instruction manual for installation, operation and maintenance of various components of

switchgear

9.17.3 Metal Enclosed LT Switchgear

Drawing and documents required
• GA drawing of each panel with foundation details

• Single line diagram for each panels

• Schematic diagrams for various modules

• GA drawing of the bus duct including supporting structure If required

• Instruction manuals - installation, operation and maintenance of switchgear

9.17.4 Battery and Charger cum DCDB

Drawing and documents required
• GA drawing of the battery and the charger cubicle

• Schematic diagram for battery and charger cum DCDB

• Instruction manual for installation, operation and maintenance for battery and charger

9.17.5 Motors
Drawing and documents required
• GA drawing of the each motor showing dimensional details and terminal box details

• Motor selection details

CONTRACTOR 95/97 SUPERINTENDINGENGINEER