Fishing and Re-entry BHA Sheet

DOCUMENT NUMBER CLASSIFICATION DOCUMENT LEVEL REVISION NO. ISSUE DATE PREPARED BY APPROVAL

GL-INTS-OEPS-L4-316 CONTROLLED L5 000 3/16/2016 TWI Committee GBU

Client: ONGC Date: 6-Oct-22

Operation: 13-3/8''QC, PHS Whipstock BHA no: 1
Rig: E-760-14 BHA Desc: Gauge Run
Well no: KJ#18 Supervisor: Joseph Martin/Shino Thomas

SCOPE: This BHA Sheet will be completed by the Field Supervisor prior to running Fishing or Re-entry equipment in the hole. At the end of the job this BHA Sheet will be uploaded to WPTS
as an attachment.

Bottom MAX Fish Neck Acc.

Item Tool Description Serial Number Top Conn. MIN ID Length Comments
Conn. OD Length
OD Length
1 Taper Mill OTI-095-2 6-5/8" Reg Pin N/A 12-1/4" 3-1/2" 8" 0.43 1.30 1.30
6-5/8" Reg
2 Casing Scrapper 252624 6-5/8" Reg Pin 3-1/2" 7-3/4" 0.34 1.25 2.55
Box
6-5/8" Reg
3 Watermelon Mill WFD 6-5/8" Reg Pin 12-1/4" 3-1/2" 8" 0.53 1.85 4.40
Box
6-5/8" Reg
4 Pony Drill Collar 302791 6-5/8" Reg Pin 3-1/2" 8" Slick 3.06 7.46
Box
6-5/8" Reg
5 Watermelon Mill 2380636 6-5/8" Reg Pin 12-1/4" 3-1/2" 7-3/4" 0.26 1 8.46
Box
6-5/8" Reg 6-5/8" Reg
6 Bit Sub 295050 8" 3" 8" Slick 0.9 9.36
Box Box
6-5/8" Reg
7 8"Drill Collar 12 Joints RIG 6-5/8" Reg Pin Rig Tally
Box
8 Croessover RIG 4"IF Box 6-5/8" Reg Pin Rig Tally

9 6-1/2"Drill Collar 3 Joints RIG 4"IF Box 4"IF Pin Rig Tally

10 Croessover RIG 4-1/2" IF Box 4"IF Pin Rig Tally

11 5"HWDP 6 Joints RIG 4-1/2" IF Box 4-1/2" IF Pin Rig Tally

12 DP to Surface RIG 4-1/2" IF Box 4-1/2" IF Pin Rig Tally

Note:Pup Joints for Space out(3",5',10')

BHA Weight
Weight below the Jars

Total BHA Length

Comments

© 2016 Weatherford All Rights Reserved Proprietary and Confidential. This document is copyrighted and contains valuable proprietary and confidential information, whether patentable or unpatentable, of Weatherford. Recipients
agree the document is loaned with confidential restrictions, and with the understanding that neither it nor the information contained therein will be reproduced, used or disclosed in whole or in part for any purpose except as may be
specifically authorized in writing by Weatherford
 Fishing and Re-entry BHA Sheet
DOCUMENT NUMBER CLASSIFICATION DOCUMENT LEVEL REVISION NO. ISSUE DATE PREPARED BY APPROVAL

GL-INTS-OEPS-L4-316 CONTROLLED L5 000 3/16/2016 TWI Committee GBU

Client: ONGC Date: 6-Oct-22

Operation: 13-3/8''QC, PHS Whipstock BHA no: 2
Rig: E-760-14 BHA Desc: Whipstock & Window Milling
Well no: KJ#18 Supervisor: Joseph Martin/Shino Thomas

SCOPE: This BHA Sheet will be completed by the Field Supervisor prior to running Fishing or Re-entry equipment in the hole. At the end of the job this BHA Sheet will be uploaded to WPTS
as an attachment.

Bottom MAX Fish Neck Acc.

Item Tool Description Serial Number Top Conn. MIN ID Length Comments
Conn. OD Length
OD Length
1 Whipstock Assembly 1220649-6 - - 11.875 9.20 9.20
6-5/8" Reg
2 Lead Mill 67831571 - 12-1/4" 0.994" 7-1/2" 0.36 0.61 9.81
Box
6-5/8" Reg
3 Flex Mill 2390317 6-5/8" Reg Pin 12-1/4" 3" 7-1/2" 0.30 1.70 11.51
Box
6-5/8" Reg
4 Flex Mandrel 1093334 6-5/8" Reg Pin 7-3/4" 3" 7-3/4" 0.39 3.65 15.16
Box
6-5/8" Reg
5 Steering Mill 10173 6-5/8" Reg Pin 12-1/4" 3" 8" 0.30 1.10 16.26
Box
6-5/8" Reg
6 8"Drill Collar 12 Joints RIG 6-5/8" Reg Pin Rig Tally
Box
7 Croessover RIG 4"IF Box 6-5/8" Reg Pin Rig Tally

8 6-1/2"Drill Collar 3 Joints RIG 4"IF Box 4"IF Pin Rig Tally
9 Croessover RIG 4-1/2" IF Box 4"IF Pin Rig Tally
10 5"HWDP 6 Joints RIG 4-1/2" IF Box 4-1/2" IF Pin Rig Tally
11 DP to Surface RIG 4-1/2" IF Box 4-1/2" IF Pin Rig Tally
Pup Joints for Space
12 RIG 4-1/2" IF Box 4-1/2" IF Pin Rig Tally
out(3",5',10')

BHA Weight
Weight below the Jars

Total BHA Length

Comments

© 2016 Weatherford All Rights Reserved Proprietary and Confidential. This document is copyrighted and contains valuable proprietary and confidential information, whether patentable or unpatentable, of Weatherford. Recipients
agree the document is loaned with confidential restrictions, and with the understanding that neither it nor the information contained therein will be reproduced, used or disclosed in whole or in part for any purpose except as may be
specifically authorized in writing by Weatherford
 EVALUATION, DRILLING and INTERVENTION

Draft Plan for 13-3/8” Whipstock setting and Window milling

Dt: 06-Oct-22

Rig: E-760-14.
Well No: KJ#18

General Plan
All in green is done before RIH

Pressure test whipstock 500 PSI for 10 minutes

Install Correct number of shear pins As per ACCU set – 06 pins

Be sure Casing is clean from cement and scale.

Have CBL and CCL handy. Be sure don’t Mill thru Casing Collar,
Pup joints to get the proper space may be needed once the setting depth is final.

Milling fluid required prior to commence milling.

• Mud presently in Hole: 1.05SG
• Weatherford Requires viscosity 70+ to lift metal cuttings while milling
• Hi Vis pill of 100+ viscosity to be prepared as and when required while milling
• % solids: less than 1-2%

Gauge Mills before RIH.

Setting depth/Bottom of Whipstock: 266.70m

Top Casing Collar (as per Casing tally): 255m
Bottom Casing Collar (as per casing Tally: 266.5m
Top of Window/Whipstock: 257.5m
Bottom of Window: 263m

BHA #1 (Gauge/Scrapper Run)

1. Measure all components prior to RIH

2. M/up Gauge/Scrapper run assembly as per BHA #1 and RIH up to 290m.
3. Scrap the whipstock setting depth 4 times. (240m to 270m)
4. Circulate well to condition mud to be used for setting whipstock. Mud system should be homogeneous with in
and out mud wt to be same prior to POOH gauge run BHA.
5. Test surface lines to 1000 psi by closing IBOP or standpipe manifold valve.
6. Function test pumps as per WFT engineer at different GPM combinations and record pressure for hydraulics at
Whipstock setting depth. (GPM 600 to 800)
7. POOH Gauge mills at controlled speed of 2 mins per stand through dog legs.
8. L/down assembly.
BHA #2 (Whipstock and Milling Run)

1. HELD PJSM.
2. Close Blind Rams.
3. P/up and M/up W/Ford Milling Assy As per BHA 2.
4. Scribe high Side as per Directional Driller.
5. Rack back/Lay down Milling Assy.
6. R/Up 2 long casing Slings to Top drive elevator bails.
7. Close Blind Rams.
8. HELD PJSM. P/Up Whipstock. Once whipstock is picked up horizontally by crane and tailed to the rig floor,
attach the slings from the top drive provided swivel to the whipstock and start to pick up slowly & set the
whipstock on Rig Floor. Install Brass shear screws as per Weatherford.
9. P/Up whipstock and set it inside the rotary table with T-Bar(W/FORD) and secure the hole.
10. P/Up milling assy and M/up with Whipstock with 48kips Shear Bolt, attach Control line. Secure the control
Line.
11. Open Blind Rams.
12. RIH 13-3/8’’ Whipstock Assy@ 3-4 mins /stand slip to slip.

• Check Tong dies and Drill pipe Slip dies, ensure it is clear prior to RIH.
• Check and Keep ready 8” and 61/2” DC Slip and Safety clamp(Dog Collar) ready.
• Drain BOP prior to RIH whipstock if hole is not centered.
• Extreme caution while passing through BOP and Well head area.
• If the string is with less weight use Dog collars.
• No rotation, No pumps, No jerking, No turning of string and No pipe Filling.
• If any held ups observed during RIH call Weatherford. Don’t Apply down weight and up weight.
• During RIH Set slips slowly.

13. Continue RIH to Setting Depth @ 266.70m Cross check the BHA and the number of pipes available in derrick.
14. Reciprocate and release trapped Torque.
15. At setting depth, Orient tool face as per Jindal/ONGC DD and Weatherford Instructions.
16. Set Whipstock as per Weatherford Instructions. Confirm Whipstock set and apply down weight of 48k to
shear attachment bolt from the whipstock and slack off weight till 65Kips to energize packer.
17. P/U 1 mtr and establish parameters. Take free torque and start Milling Operation at top of whipstock as per
Whipstock engr. Viscosity – 70/80.
18. Pump 20 Barrel High Viscosity sweep every 1meter or 1 hour milled
 19. Keep good Record on Weatherford provided Milling sheet.
20. Finish milling 5.5 Mtrs Window & 7 Mtrs rat-hole.
21. Ream window & Rat hole for several times with Different RPM, pass window with and without rotation, pass
window with and without pumps. Call Directional Driller to check window.
22. Once confirmed and agreed by all parties, pump 30 Barrel Sweep bottoms Up & Pull out of hole.
23. POOH check gauge Q C Mills*. All Tools back to Tool baskets
24. Pick Drilling BHA & Start Drilling Program

Rig Preparation:
➢ Pup Joints (3’,5’ and 10’) required as per BHA 1 and 2 for space out.
➢ X-overs required as per BHA 1 & 2.
➢ 2 long casing slings and shackles for whipstock ( 4.5 tons)
➢ Install Ditch magnets in flow line and shakers.
➢ Clean and collect metal cuttings. ( Use rubber Gloves).

*Note:
Note: An additional /clean out run has to be done only if mills are coming out of the hole more
than ¼” under gauge as per Weatherford specifications.