8 7 6 5 4 3 2 1

NOTES:
1. THIS DRAWING DESCRIBES THE FUELAB MODEL 253xx SERIES IN-TANK Flow Performance at 13.8V, Models 25301, 25302,
FUEL PUMP KIT.
25303, and 25304
2. FEATURES INCLUDE: 500 F
F - THREE PHASE DC BRUSHLESS SCREW PUMP WITH TURBINE PUMP
- IN-TANK PUMP CONFIGURATION FOR EASY INSTALLATION 450
- EXTERNAL DC BRUSHLESS CONTROLLER WITH PWM SPEED CONTROL
- THREE WIRE BULKHEAD FEEDTHRU WITH TEFLON INSULATION 400
- IN-TANK STRAINING FILTER
350

Flow Rate (LPH)

3. FUEL COMPATIBILITY INCLUDES:
- GASOLINE (PUMP OR RACE) 300
- METHANOL
- ETHANOL (INCLUDING E85) 250
- DIESEL
200
4. UNIQUE SERIAL NUMBERS DO NOT CONTAIN DIRECT INFORMATION
IN DETERMINING MODEL NUMBER. CONTACT FUELAB FOR 150
E DETERMINATION OF MODEL NUMBER BASED ON SERIAL NUMBER. E
100
5. INSTRUCTIONS AND PERFORMANCE CERTIFICATION INCLUDED, BAGGED
SEPARATELY FROM PUMP. REFERENCE SUBSEQUENT SHEETS FOR FULL 50
KIT CONTENTS OF THE VARIOUS AVILABLE MODELS.
0
6. 8-16 VOLT OPERATING RANGE, USE ONLY 12 VOLT (6 CELL LEAD 0 1 2 3 4 5 6
ACID BATTERY) VEHICLE SYSTEMS WITH OR WITHOUT CHARGING
SYSTEM. Outlet Pressure (Bar)

7. SYSTEM REQUIRES BYPASS REGULATOR OR RELIEF VALVE TO AVOID

OVER-PRESSURE OPERATING CONDITION. SYSTEM REQUIRES 20 AMP
RELAY AND FUSE. ADDITIONAL PLUMBING REQUIRED FOR OUTLET FLOW. Flow Performance at 13.8V, Models 25311, 25312,
25313, and 25314
D 8. SEE TABLE BELOW FOR DETERMINATION OF DESIRED MODEL NUMBER. D
MODELS 25304 AND 25314 HAS ADDITIONAL 6mm OUTLET FOR USE WITH 700
JET PUMP (EDUCTOR) SYSTEM. BOTH OUTLETS CONTAIN CHECK VALVE.
ALL OTHER PUMPS DO NOT HAVE BUILT IN CHECK VALVES.
600
MODEL SELECTION TABLE
500
OUTLET TYPE FLOW RATING, AT 13.8v MAX. PRESSURE

Flow Rate (LPH)

MODEL SPECIAL FEATURES
25301 -6AN 92 GPH AT 45 PSI (350 LPH AT 3.0 BAR) 125 PSI (8.6 BAR)
125 PSI (8.6 BAR)
400
25302 5/16" SAE 92 GPH AT 45 PSI (350 LPH AT 3.0 BAR)
25303 3/8" SAE 92 GPH AT 45 PSI (350 LPH AT 3.0 BAR) 125 PSI (8.6 BAR)
25304 9mm BARBED 92 GPH AT 45 PSI (350 LPH AT 3.0 BAR) 125 PSI (8.6 BAR) AUX 6mm BARB SIPHON
300
8.
25311 -6AN 132 GPH AT 45 PSI (500 LPH AT 3.0 BAR) 125 PSI (8.6 BAR)
C 25312 5/16" SAE 132 GPH AT 45 PSI (500 LPH AT 3.0 BAR) 125 PSI (8.6 BAR) 200 C

25313 3/8" SAE 132 GPH AT 45 PSI (500 LPH AT 3.0 BAR) 125 PSI (8.6 BAR)
8. 100
25314 9mm BARBED 132 GPH AT 45 PSI (500 LPH AT 3.0 BAR) 125 PSI (8.6 BAR) AUX 6mm BARB SIPHON

0
0 1 2 3 4 5 6
Outlet Pressure (Bar)

Current Draw Performance at 13.8V, Models 25301, Current Draw Performance at 13.8V, Model 25311,
B
25302, 25303, and 25304 25312, 25313, and 25314 B
14.0 16.0
Current Draw (Amperes)

Current Draw (Amperes)

12.0 14.0

10.0 12.0
10.0
8.0
8.0
6.0
6.0
4.0 4.0
2.0 2.0
UNLESS OTHERWISE SPECIFIED:
INTERPRET DWG PER ANSI Y14.5
Collinsville, Illinois
DIMENSIONS ARE IN INCHES
0.0 0.0 TOLERANCES:
FRACTIONAL: 1/64"
TITLE:
A A
0 1 2 3 4 5 6 0 1 2 3 4 5 6 ANGULAR: 1/2°
DECIMALS:
IN-TANK PUMP KIT,
.X .1 .XX .03 .XXX .010

Outlet Pressure (Bar) Outlet Pressure (Bar) SURFACE FINISH

128
OR BETTER 253xx SERIES
BREAK ALL SHARP EDGES .010 MAX
REMOVE ALL BURRS
SIZE DWG. NO. REV
THIRD ANGLE
PROJECTION C 153020100
DO NOT SCALE DRAWING SCALE: 1/2 WEIGHT: SHEET: 1 OF 3
8 7 6 5 4 3 2 1
 8 7 6 5 4 3 2 1

F
F

FUEL PUMP PER FUEL PUMP PER

MODEL 49601 OR 49611 MODEL 49602 OR 49612
INLET STRAINING FILTER INLET STRAINING FILTER

PIGTAIL
CONNECTOR
PIGTAIL
CONNECTOR

CONTROLLER PER
MODEL 72002
E E
CONTROLLER PER
MODEL 72002

BULKHEAD
FEEDTHRU PER BULKHEAD
MODEL 74101 FEEDTHRU PER
MODEL 74101

BUTT SPLICES
WITH FUEL RESISTANT
SHRINK WRAP BUTT SPLICES
WITH FUEL RESISTANT
D SHRINK WRAP D

C C

DELPHI (APTIV)
WEATHER PACK DELPHI (APTIV)
3-WIRE WEATHER PACK
CONNECTORS 3-WIRE
CONNECTORS

B CONTENTS OF KIT PER MODEL 25301 AND 25311 SHOWN ABOVE CONTENTS OF KIT PER MODEL 25302 AND 25312 SHOWN ABOVE B

REFERENCE 110021300, 120020100, AND 141020100 FOR EXTRA REFERENCE 110021300, 120020100, AND 141020100 FOR EXTRA
DETAILS INCLUDING DIMENSIONS, PERTAINING TO INCLUDED MODELS DETAILS INCLUDING DIMENSIONS, PERTAINING TO INCLUDED MODELS

UNLESS OTHERWISE SPECIFIED:

INTERPRET DWG PER ANSI Y14.5
Collinsville, Illinois
DIMENSIONS ARE IN INCHES
TOLERANCES: TITLE:
FRACTIONAL: 1/64"
A ANGULAR: 1/2° A
DECIMALS:
.X .1 .XX .03 .XXX .010
IN-TANK PUMP KIT,
SURFACE FINISH
128
OR BETTER 253xx SERIES
BREAK ALL SHARP EDGES .010 MAX
REMOVE ALL BURRS
SIZE DWG. NO. REV
THIRD ANGLE
PROJECTION C 153020100
DO NOT SCALE DRAWING SCALE: 1/2 WEIGHT: SHEET: 2 OF 3
8 7 6 5 4 3 2 1
 8 7 6 5 4 3 2 1

FUEL PUMP PER

MODEL 49603 OR 49613
F
INLET STRAINING FILTER
F FUEL PUMP PER
MODEL 49604 OR 49614

PIGTAIL
CONNECTOR INLET STRAINING FILTER

PIGTAIL
CONTROLLER PER CONNECTOR
MODEL 72002
ASSORTED
HOSE CLAMPS

E E
BULKHEAD
FEEDTHRU PER
MODEL 74101

BUTT SPLICES
WITH FUEL RESISTANT NYLON OUTLET
SHRINK WRAP HOSE

D
BUTT SPLICES D
WITH FUEL RESISTANT CONTROLLER PER
SHRINK WRAP MODEL 72002
BULKHEAD
FEEDTHRU PER
MODEL 74101

C C
DELPHI (APTIV)
WEATHER PACK
3-WIRE
CONNECTORS

CONTENTS OF KIT PER MODEL 25303 AND 25313 SHOWN ABOVE

REFERENCE 110021300, 120020100, AND 141020100 FOR EXTRA
DETAILS INCLUDING DIMENSIONS, PERTAINING TO INCLUDED MODELS
DELPHI (APTIV)
B WEATHER PACK B
3-WIRE
CONNECTORS

CONTENTS OF KIT PER MODEL 25304 AND 25314 SHOWN ABOVE

REFERENCE 110021300, 120020100, AND 141020100 FOR EXTRA
DETAILS INCLUDING DIMENSIONS, PERTAINING TO INCLUDED MODELS

UNLESS OTHERWISE SPECIFIED:

INTERPRET DWG PER ANSI Y14.5
Collinsville, Illinois
DIMENSIONS ARE IN INCHES
TOLERANCES: TITLE:
FRACTIONAL: 1/64"
A ANGULAR: 1/2° A
DECIMALS:
.X .1 .XX .03 .XXX .010
IN-TANK PUMP KIT,
SURFACE FINISH
128
OR BETTER 253xx SERIES
BREAK ALL SHARP EDGES .010 MAX
REMOVE ALL BURRS
SIZE DWG. NO. REV
THIRD ANGLE
PROJECTION C 153020100
DO NOT SCALE DRAWING SCALE: 1/2 WEIGHT: SHEET: 3 OF 3
8 7 6 5 4 3 2 1