Scribd
Upload
2K views

Types of Faults in Power System

There are two main types of faults in power systems: open circuit faults and short circuit faults. Open circuit faults occur when one or more conductors fail, disrupting the intended flow of current. Short circuit faults happen when conductors from different phases come into contact, allowing large currents to flow. Short circuits can be symmetrical, involving all three phases, or unsymmetrical, involving one or two phases. Common causes of faults include lightning, high winds, accidents, and equipment failures. Devices like fuses, circuit breakers, and protective relays are used to detect and quickly clear faults to prevent equipment damage and power disruptions.

Uploaded by

Mohamed Rafaat
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
2K views

Types of Faults in Power System

There are two main types of faults in power systems: open circuit faults and short circuit faults. Open circuit faults occur when one or more conductors fail, disrupting the intended flow of current. Short circuit faults happen when conductors from different phases come into contact, allowing large currents to flow. Short circuits can be symmetrical, involving all three phases, or unsymmetrical, involving one or two phases. Common causes of faults include lightning, high winds, accidents, and equipment failures. Devices like fuses, circuit breakers, and protective relays are used to detect and quickly clear faults to prevent equipment damage and power disruptions.

Uploaded by

Mohamed Rafaat
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

Types of Faults in Power System

The fault in the power system is defined as the defect in the power system due
to which the current is distracted from the intended path. The fault creates the
abnormal condition which reduces the insulation strength between the
conductors. The reduction in insulation causes excessive damage to the
system. The fault in the power system is mainly categorised into two types they
are

1. Open Circuit Fault


2. Short Circuit Fault.
The different types of power system fault
are shown below in the image.

The faults in the power system may occur


because of the number of natural
disturbances like lightning, high-speed
winds, earthquake, etc. It may also occur
because of some accidents like falling off
a tree, vehicle colliding, with supporting
structure, aeroplane crashing, etc.

1. Open Circuit Fault


The open circuit fault mainly occurs because of the failure of one or two
conductors. The open circuit fault takes place in series with the line, and
because of this, it is also called the series fault. Such types of faults affect the
reliability of the system. The open circuit fault is categorised  as

 Open Conductor Fault


 Two conductors Open Fault
 Three conductors Open Fault.
The open circuit fault is shown in the figure below.
2. Short-Circuit Fault
In this type of fault, the conductors of the different phases come into contact
with each other with a power line, power transformer or any other circuit
element due to which the large current flow in one or two phases of the system.
The short-circuit fault is divided into the symmetrical and unsymmetrical fault.

Symmetrical Fault
The faults which involve all the three phases is known as the symmetrical fault.
Such types of fault remain balanced even after the fault. The symmetrical faults
mainly occur at the terminal of the generators. The fault on the system may
arise on account of the resistance of the arc between the conductors or due to
the lower footing resistance. The symmetrical fault is sub-categorized into line-
to-line-to-line fault and three-phase line-to-ground-fault

a. Line – Line – Line Fault – Such types of


faults are balanced, i.e., the system remains
symmetrical even after the fault. The L – L –
L fault occurs rarely, but it is the most severe
type of fault which involves the largest
current. This large current is used for
determining the rating of the circuit breaker.

b. L – L – L – G (Three-phase line to the


ground fault) – The three-phase line to
ground fault includes all the three phase of
the system. The L – L – L – G fault occurs
between the three phases and the ground of
the system. The probability of occurrence of
such type of fault is nearly 2 to 3 percent.
Unsymmetrical Fault
The fault gives rise to unsymmetrical current, i.e., current differing in
magnitude and phases in the three phases of the power system are known as the
unsymmetrical fault. It is also defined as the fault which involves the one or two
phases such as L- G, L – L, L – L – G fault. The unsymmetrical makes the
system unbalanced. It is mainly classified into three types. They are

1. Single Line-to-ground (L – G) Fault


2. Line-to-Line Fault (L – L)
3. Double Line-to-ground (L – L – G) Fault
The unsymmetrical fault is the most common types of fault occur in the power
system.

1. Single Line-to-Line Ground – The single


line of ground fault occurs when one conductor
falls to the ground or contact the neutral
conductor. The 70 – 80 percent of the fault in
the power system is the single line-to-ground
fault.

2. Line – to – Line Fault  –  A line-to-line fault occurs when two conductors


are short circuited. The major cause of this type
of fault is the heavy wind. The heavy wind
swinging the line conductors which may touch
together and hence cause short-circuit. The
percentage of such type of faults is
approximately 15 – 20%.

3. Double Line – to – line Ground Fault – In


double line-to-ground fault, the two lines come
in contact with each other along with the
ground. The probability of such types of faults
is nearly 10 %.

The symmetrical and unsymmetrical fault


mainly occurs in the terminal of the generator,
and the open circuit and short circuit fault
occur on the transmission line.
Protection Devices against Faults
When the fault occurs in any part of the system, it must be cleared in a very short
period in order to avoid greater damage to equipments and personnel and also to avoid
interruption of power to the customers.

The fault clearing system uses various protection devices such as relays and circuit
breakers to detect and clear the fault.
Some of these fault clearing or faults limiting devices are given below.

1. Fuse
It opens the circuit whenever a fault exists in the
system. It consists of a thin copper wire enclosed
in a glass or a casing with two metallic contacts.
The high fault current rises the temperature of
the wire and hence it melts. A fuse necessitates
the manual replacement of wire each time when
it blows.

Fuse
2. Circuit Breaker
It is the most common protection device that can
make or break the circuit either manually or through
remote control under normal operating conditions.

There are several types of circuit breakers available


depending on the operating voltage, including air
brake, oil, vacuum and SF6 circuit breakers. For
more information on circuit breakers, follow the link
attached. Circuit Breaker

3. Protective Relays
These are the fault detecting devices. These
devices detect the fault and initiate the operation
of the circuit breaker so as to isolate the faulty
circuit. A relay consists of a magnetic coil and
contacts (NC and NO). The fault current
energizes the coil and this causes to produce the
field, thereby the contacts get operated.

 Magnitude relays Some of the types of protective


relays include
 Impedance relays
 Directional relays
 Pilot relays
 Differential relays
4. Lighting Arrestor
Surges in the power system network caused when lightning strikes on transmission
lines and equipments. This causes high voltage and currents in the system. These
lighting faults are reduced by placing lighting arrestors at transmission equipments.

Image Contributors:

1)Electrical Faults: forschung-stromnetze.info 

2) Fuse : hayley-group.co.uk

3)Circuit Breaker : oez.com

You might also like