CLEANING AND REPAIR OF VALVES A-7 & B-7 VALVES This is a very dependable

MILITARY VALVES The insert of the military valve and almost never needs replacing. Again,
valve can be removed, cleaned and replaced if the use of 303 Protectant in the valve will prevent
necessary. This insert is held in place by small build up of salt and sand deposits on the rubber
screws. Use care not to over tighten the screws seat. If leakage cannot be stopped, the valve will
when reinstalling the insert into the valve boot. require a new insert. Inserts may be replaced
Should your valve boot need replacing, you can without the removal of the whole valve. To remove
do one of two things: a) Replace the valve boot or an A-7 or B-7 insert:
b) Use this opportunity to replace your old military
valve with a new C-7 valve (*see below). Once A. With the boat
deflated, grasp the
again, the use of 303 Protectant helps maintain
the rubber seal of the valve. inside part of the Repairing Hypalon Boats
valve body with
C-7 VALVE & A-6 PRESSURE RELIEF VALVE your hand. Using
Quickly becoming the standard in the industry, channel locks, grab
onto the outside The first and foremost thing to remember
these two valves are used in all Avons (2000 & (A)
later). They are a surface mounted valve (no part of the valve and when repairing a boat is that proper
boot) and have a very low profile. They operate unscrew the valve. preparation is the key to an effective
much like the old A-7 but when the insert needs repair. The use of proper adhesives is
B. Now you need
replacing you simply unscrew the valve with a also a critical element to any repair.
C-7 wrench and screw in a new core which has to manipulate and
rotate the part of Whether done in the field or in your shop,
the insert built into it. The same applies to the A-6 take your time to make sure the job is
PRV valve that is used in floors. the valve body that
is inside the boat (B) done right.
REPLACING A “BOOT VALVE” WITH A C-7 so you can see the
Utilizing the same techniques to remove D-Rings black diaphragm Repair material should overlap the repair
and other accessories, remove the valve boot. through the hole by no less than 1” and no more than 2”.
Now, cut a circle of Avon material 1 1/2” larger in in the boat . Push The air holding seams on Avon Riverboats
the insert with
diameter than the hole in your thwart or tube. In are glued together with a 1 1/2” overlap,
the center of this material cut a hole no smaller your finger so
the diaphragm so if a repair is made overlapping the
than 1 1/8” and no larger than 1 1/4” – this creates damaged area by 1 1/2” , the repair will
a Hypalon “donut”. VERY IMPORTANT – Install is sticking up.
Now unscrew the (C) be just as strong as the factory seams that
the C-7 Valve to the donut before gluing the donut
to boat. Prep and glue the donut to the boat. diaphragm from the hold the boat together.
white stem while keeping back pressure on the
stem. (it may break but you are putting a new one
in anyway)

C. Now you need to rotate the valve body one

more time while holding the stem so you can Clavey River Equipment
remove the stem and spring.
409 Petaluma Blvd. S, Petaluma, CA 94953
Install the new insert by using the above method
in reverse. Once the new insert is installed screw 707-766-8070
the valve back together tightly.
For info call 1-80 0-832-4226 For info call 1-80 0-832-4226
 PREPARATION FOR REPAIRS ON SMALL Mixing instructions for Bostik 3. Apply a second coat to both boat and patch.
CUTS, PERFORATIONS AND LARGE TEARS Wait about five minutes or until glue is still tacky
two-part Adhesive to the touch. Press the patch onto the boat
Make sure surfaces to be joined are clean and First and foremost please remember that Bostik starting from the center and working towards
dry. Repairs should be made in the shade when is nasty stuff. Always work in a well ventilated the edge. The edge of the patch cannot extend
possible. Hot temperatures and direct sunlight area and protect yourself with nitrile gloves and beyond the buffed and glued area – This will
will cause the glue to set faster. Humidity and an organic chemical respirator. *Latex gloves will cause the edge to eventually lift.
cold will cause the glue to set more slowly. allow the Toluol to absorb through the glove and
into your bloodstream – use nitrile gloves. 4. Press the entire patch very hard (working from
1. Cut a suitable size patch, overlapping the
the center out) with a blunt round tool or roller.
damaged area by 1 1/2”. Round the edges of the Prepare adhesive (remember only to prepare what A putty knife with rounded edges works well for
patch. you can use in approximately ninety minutes). this.
Use approx. 10 drops Bostikure accelerator per
2. Place patch over the cut or puncture and ounce of Bostik glue 5. Clean excess glue from around the patch
outline with a ball point pen or grease pencil, 1 oz. of glue - mix with 10 drops Bostikure accel- with Toluol and a rag or a nylon rotary brush
making sure all edges of the patch are at least erator attachment on a drill. Let the patch cure at least
1” from the hole. Avoid overlapping a seam, as a 2 oz. of glue - mix with 20 drops. four hours, but preferably 12 to 24 hours.
patch over a seam is more likely to leak. For one 1/4 liter can of Bostik use one entire bottle
of Bostikure accelerator.
3. Using coarse sand paper, buff the area Mix glue and accelerator well before applying.
including the pen marking and the bottom side of REPAIRS OF CUTS THAT ARE CLOSE TO
Remember that this is a rough measurement.
the patch. Be careful not to buff outside the area Bostikure is an accelerator - the more you use the D-RINGS, RUB STRAKE OR ACCESSORIES
to be patched. Care must be taken not to remove faster the glue will set up. Bostik will work without 1. When at all possible, do not apply a patch that
so much Hypalon that the polyester core is the accelerator but it will take a long time to set overlaps rub strake, floor seams, D-Rings etc. Air
exposed. All traces of old glue and dust must be up. If you use too much accelerator the glue will will leak around the overlapped seams.
removed with Toluol. The surfaces should have a become brittle.
matte appearance and be clean and dry. Buffing CAUTION: Always clean the rim of the glue can 2. Removing an accessory is required if it is within
is best done on a flat surface. to allow lid to seal tightly and keep the neck of the 1” of the hole. To remove a glued-on item or open
Bostikure bottle wiped clean to avoid cap from a seam, use a non-contact heat source (such as
4. With a clean, lint free rag, clean both the patch
adhering to bottle. a hair dryer or heat gun). Apply heat and slowly
and the area to be patched thoroughly, two to
work a corner loose with a spatula or rounded
three times, with Toluol. *Do not use an oil based
Applying Adhesive putty knife. Great care must be taken not to tear
solvent such as paint thinner.
away the Hypalon coating from the polyester
1. Take a 1” paint brush and cut off the bottom half
fabric. Heat and careful working with the putty
POLYURETHANE REPAIRS When repairing of the bristles. This works well for spreading glue.
knife will enable you to remove any patch or
the polyurethane chafe or bottoms on newer
open any seam without damaging the material.
Avons, the same procedure and glue are 2. Apply a thin coat of adhesive to boat and patch.
Remember: Take your time.
used as Hypalon with one exception: Prep the Let dry until it is no longer tacky to the touch -
polyurethane with MEK instead of Toluol. The about 7 to 10 min.
3. Apply the repair patch over the hole as
Hypalon will still need Toluol.
described previously. Then reapply the rub
strake, D-Ring, etc. that was peeled up in a similar
fashion.

For info call 1-80 0-832-4226 For info call 1-80 0-832-4226 For info call 1-80 0-832-4226