Scribd
Upload
70 views

Water Level Indicator

This document describes a transistor-based water level indicator alarm circuit. The circuit uses transistors as switches to detect four different water levels in a tank - low, medium, high, and full. LEDs light up green, yellow, and orange to indicate the initial three levels. A buzzer sounds when the tank reaches the full level. The circuit works by applying voltage to the transistor bases through contact with the water at different points, turning the transistors on and allowing current to flow through the corresponding LED or buzzer. Resistors are included to limit current and drop voltage across the LEDs.

Uploaded by

Kumar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
70 views

Water Level Indicator

This document describes a transistor-based water level indicator alarm circuit. The circuit uses transistors as switches to detect four different water levels in a tank - low, medium, high, and full. LEDs light up green, yellow, and orange to indicate the initial three levels. A buzzer sounds when the tank reaches the full level. The circuit works by applying voltage to the transistor bases through contact with the water at different points, turning the transistors on and allowing current to flow through the corresponding LED or buzzer. Resistors are included to limit current and drop voltage across the LEDs.

Uploaded by

Kumar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 9

Dr.Maheswari.

R
TITLE OF THE EXPERIMENT:-

Title:-Transistor based Water Level Indicator Alarm/ Buzzer

Abstract:-
Water tank overflow is a common problem which leads to the wastage of water. Though there are
many solutions to it like ball valves which automatically stop the water flow once the tank gets
full. It is a simple circuit which will detect the water level and will raise an alarm upon getting the
water tank full or a preset level. This simple transistor based water level indicator circuit is
very useful to indicate the water levels in a tank. Whenever tank gets filled, we get alerts on
particular levels. Here we have created 4 levels (low, medium, high and full), we can create alarms
for more levels. We have added 3 LEDs to indicate initial three levels (A, B, C), and one Buzzer
to indicate FULL level (D). When tanks gets filled completely we get beep sound from Buzzer.

Circuit Diagram:
eSim Required Components:-

Circuit Description:-
We can consider this whole circuit as 4 small circuits, each one for indicating/alarming, when a
particular level of water have been reached. When water level reaches to a particular level (Level
1, 2, 3) then the Led corresponding to that level (Green, Yellow, Orange) will start glowing. And
finally when tank gets full (Level 4), circuit with buzzer and corresponding Led gets completed
and buzzer starts beeping and Led (Red) starts glowing.
Working

Here we are using transistor (of NPN type) as a Switch. Initially there is no voltage applied to the
base of the Transistor Q1 and the transistor is in OFF state and no current is flowing through
collector and emitter and LED is OFF (See below diagram to understand Transistor Pin structure).

When the water level reaches to Point A in the tank, the positive side of the battery gets connected
to the base of the Transistor Q1 through the water. So when a positive voltage has been applied to
the base of the Transistor Q1, it gets into ON state and current starts flowing from collector to
emitter. And RED LED glows. You can see resistors (R1, R2, R3) at the base of each transistor,
which is used to limit the maximum Base current. Generally a transistor gets its ON state fully
when a voltage of 0.7 V is applied to the base. There are also resistors (R4, R5, R6) with each of
the LEDs, to drop the voltage across LEDs, otherwise LED may blow up. Same phenomenon
happens when water level reaches to Point B. As soon as water level reaches to Point B, a positive
voltage gets applied to the Transistor Q2, it gets ON and current started flowing through YELLOW
LED, and LED glows. With same principle, GREEN LED glow when water level reaches to Point
C. And finally Buzzer beeps when water level reaches to D.
References:-
 https://circuitdigest.com/electronic-circuits/water-level-indicator-alarm-circuit

You might also like