Scribd
Upload
78 views

Calculation For Scaffolding

This document provides the design criteria, loads, analysis, and results for scaffolding at the Mong Duong II Thermal Power Plant. The scaffolding was designed according to Vietnamese and international codes using SAP2000 software. The analysis found that all steel members meet the strength requirements and have deflections under the allowable limit.

Uploaded by

Nguyễn Trung Kiên
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
78 views

Calculation For Scaffolding

This document provides the design criteria, loads, analysis, and results for scaffolding at the Mong Duong II Thermal Power Plant. The scaffolding was designed according to Vietnamese and international codes using SAP2000 software. The analysis found that all steel members meet the strength requirements and have deflections under the allowable limit.

Uploaded by

Nguyễn Trung Kiên
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 8

MONG DUONG II THERMAL POWER PLANT

CALCULATION FOR SCAFFOLDING

0 07-SEP-2022 Issued for Review

REV. NO. DATE DESCRIPTION PREP'N CHECK REVIEW APPROVAL

Page 1
MONG DUONG II THERMAL POWER PLANT DOC. No:

REV. No: 0
CALCULATION FOR SCAFFOLDING
PAGE:

CONTENTS
1. DESIGN CRITERIA

1.1 DESIGN CODE AND STANDARD

1.2 MATERIAL SPECIFICATION

1.3 DEFORMATION

1.4 COMPUTER PROGRAME


2. DESIGN LOAD

2.1 SELF WEIGHT

2.2 LIVE LOAD


3. LOAD COMBINATION

4. STRUCTURE ANALYSIS
4.1 MODELING
4.2 ANYLYSIS RESULT

Page 2
MONG DUONG II THERMAL POWER PLANT DOC. No:

-
CALCULATION FOR SCAFFOLDING REV. No: 0
PAGE:

1. DESIGN CRITERIA
1.1 DESIGN CODE AND STANDARD
Codes and Standards applied for design of farm tank foundation shall be follows:
TCVN 2737:1995 Design Standard for Load and Load Effect
AISC 360-05 (ASD) Specification for Structural Steel Buildings
ASCE 7-05 Minimum Design Loads for Buildings and other Structures
1.2 MATERIAL SPECIFICATION
Steel structure
All steel materials are JIS G 3101 (SS400) or ASTM A36 or equivalent
The minimum yield strength for shape steel fy = 245 MPa
The minimum yield strength for steel plate t <=16mm fy = 245 MPa
16< t <=40mm fy = 235 MPa
High Strength Bolt
High Strength Bolt shall be in accordance with ASTM A325 or equivalent.
The minimum tensile strength fu = 830 MPa
1.3 DEFORMATION
1) Deformation of moment member shall not be more than values in Table 1

14-JUN-2022

2) Lateral allowable movement for 1-storey industrial building without crane under standard wind load
is limited as below:
- For steel sheet wall : H/100
- For light weight wall : H/150
- For brick or concrete wall : H/200
Where : H is the column height

Page 3
MONG DUONG II THERMAL POWER PLANT DOC. No:

-
CALCULATION FOR SCAFFOLDING REV. No: 0
PAGE:

1.4 COMPUTER PROGRAM


SAP 2000 v.22
2. DESIGN LOAD
2.1 SELF-WEIGHT (SW)
The self-weight of steel structural members, is automatically generated by computer program
increased by 5% for contingency factor.
2.2 LIVE LOAD (LL)
Maximum allowable load is ~25 kg
Live load (LL) = standard load x DAF =25*3 =75 kg
Where
DAF: Dynamic Amplification factor =3

3. LOAD COMBINATION
1. Combination load for Steel design (ASD)
101 1.0 DL
102 1.0 DL + 1.0 LL
EVN1 Envelope (101~102)
Where:
DL: Dead Load
LL: Live load

4. STRUCTURE ANALYSIS
4.1 MODELING

SCAFFOLDING FRAME

Page 4
MONG DUONG II THERMAL POWER PLANT DOC. No:

-
CALCULATION FOR SCAFFOLDING REV. No: 0
PAGE:

SECTION FRAME

LIVE LOAD

Page 5
MONG DUONG II THERMAL POWER PLANT DOC. No:

-
CALCULATION FOR SCAFFOLDING REV. No: 0
PAGE:

4.2 ANALYSIS RESULT


1) Steel member check

Unit Section PMM Ratio Check


1 2xD48.3*3.2 0.036 < 1.0 OK

2XD48.3*3.2

RATIO PM

Page 6
MONG DUONG II THERMAL POWER PLANT DOC. No:

-
CALCULATION FOR SCAFFOLDING REV. No: 0
PAGE:

2XD48.3*3.2

Page 7
MONG DUONG II THERMAL POWER PLANT DOC. No:

-
CALCULATION FOR SCAFFOLDING REV. No: 0
PAGE:

2) Deflection check

Unit #1
Maximum lateral deflection u3 = 0.0563 mm
Limit lateral deflection [u3] = L/250 = 600/250= 2,4 mm
=> OK

Page 8

You might also like