CSM-321S

DMT-AL/VL AC CURRENT / VOLTAGE Transducer

 FEATURE
● FOR AC CURRENT 0~1/~5/~10A,

CS2-F
VOLTS 0~150/~300/~500V
● 1Phase(1 I/O), 3Phases(3 I/O)
● True RMS measurement for distorted waveform
● Self powered or Loop powered models available
● Output signal programmable by dip-switch

CSM-321S CSM- CSM-321S CSM- CSM-321S CSM- CSM-321S CSM- DMT-AL/VL CSM-
● Low output ripple
● High impulse & Surge protection
● High stability & low cost
● Comply with IEC688

 SPECIFICATION Storage temperature: -10~70 ℃

INPUT: Current or Voltage Dielectric Strength: IEC 414, IEC 688:1992, ANSI C37.90a
Input Input Between Input / Output / Power / Case
AC Input
Burden Frequency AC 5KV, 50/60Hz, 1 min.
0~1A 50 Hz ± 3 Hz Surge test: IEC 255-4, ANSI C37.90a
Aux. Powered &
0~5A ≦0.10VA 60 Hz ± 3 Hz 6KV, 1.2 x 50 µsec.
Loop Powered
Current 0 ~ 10 A Common mode & differential mode
20%~100% 50 Hz ± 1 Hz Insulation resistance: ≧ 100M ohm, DC 500V
Self Powered of input range
≦1.50VA
60 Hz ± 1 Hz Safety: IEC 414, BS 5458
0 ~ 150 V Enclosure: IEC 529 (IP50)
Aux. Powered & 50 Hz ± 3 Hz
0 ~ 300 V ≦0.15VA Mounting: Wall or DIN rail (EN 50022)
Loop Powered 60 Hz ± 3 Hz
Voltage 0 ~ 500 V Weight: 1P: under 450g, 3P: under 650g
20%~100% 50 Hz ± 1 Hz
Self Powered of input range
≦4.00VA
60 Hz ± 1 Hz
OUTPUT: Current or Voltage O/P Programming by Dip Switch inside  ADJUSTMENT
Load Output Output
Output Range Volt or Current – 1 Phase
Resistance Resistance Ripple
0~1V ≧500Ω
Self-powered units can not be used
for 4~20mA, 1~5V and 2~10V output.

0~5V ≧500Ω;Self Powered:≧2KΩ

1 2 3 4
0 ~ 10 V ≧1000Ω;Self Powered:≧2KΩ ≦0.001Ω 1 Volt or Current -Span Adjust Pot (Clockwise: PV increase)
1~5V ≧500Ω SPAN 2 Volt or Current -Zero Adjust Pot (Clockwise: PV increase)
2 ~ 10 V ≧1000Ω
Z ERO
0 ~ 1 mA 0 ~ 12KΩ ≧ 20MΩ ≦0.2%
0 ~ 10 mA 0 ~ 1200Ω;Self Powered:≧500Ω R.O.
Volt or Current – 3 Phases
0 ~ 20 mA 0 ~ 600Ω;Self Powered:≧500Ω
4 ~ 20 mA 0 ~ 600Ω
≧ 6MΩ
Loop Powered Vs / (20 mA) - 900 ohm 1 2 3 4 5 6 7 8
4 ~ 20 mA A B C

ZERO SPAN Z ERO SPAN Z ERO SPAN

C Phase -Span Adjust Pot (Clockwise: PV increase)
※When Aux Powered is DC，The Load Resistance is about 70% C Phase -Zero Adjust Pot (Clockwise: PV increase)
Accuracy : ≦ ±0.2% of F.S. B Phase -Span Adjust Pot (Clockwise: PV increase)
Self Powered≦ ±0.2% of F.S B Phase -Zero Adjust Pot (Clockwise: PV increase)
Waveform effect (trms type): ≦ 0.2% of F.S. at 30% distortion A Phase -Span Adjust Pot (Clockwise: PV increase)
Max. input over capability: Voltage: 1.5 x rated continuous A Phase -Zero Adjust Pot (Clockwise: PV increase)
2 x rated for 10 seconds
4 x rated for 2 seconds
Current: 3 x rated continuous  DIMENSIONS
10 x rated for 10 seconds 100.0 55.0
50 x rated for 1 second
Response time: ≦ 300 msec.
1 2 3 4 5 6 7 8 1 2 3 4
Span adjustment: ≦ ±5% of F.S. (or ±20% of F.S. specify)
Zero adjustment: ≦ ±2% of F.S. (or ±20% of F.S. specify) 75.0 SPA N

ZERO SPAN Z ER O SPAN Z ER O SPAN ZERO

Output load effect: Current output ≦ 0.1% of F.S.
9 10 11 12 13 14 15 16 5 6 7 8
Voltage output ≦ 0.05% of F.S.
Power supply: Aux Hi 85~264V AC/ DC
Aux Low:20~56V AC/ DC
16 – M4 X 10

Loop powered DC 18 ~ 32V

Self Powered: Not required

118.0
Power effect: ≦ 0.05% of F.S. ≦
Power consumption: ≦ 2.5VA (1P2W models) ≦ 6.5VA (3P3W models)
≦9 VA(ADH / ADL) 35mm Rail
Mutual interference effect: ≦ 0.1% R.O. between each element 4 - M3 X 8 (DIN 46277)

Magnetic field strength: 400ATM ≦ 0.2% of F.S.

Operating temperature: Unit: mm
0~60 ℃ 70.0

DMT-AL/VL
 CSM-321S
Temperature coefficient: ≦ 100 PPM/℃

 PANEL MOUNTING HOLES ● 1 Phase ( Self Powered )

2-6Φ Current Input: Voltage Input:
CS2-F

45.0 45.0 2-5Φ 90.0

INPUT INPUT
Ak Al P ±
60.0 1 2 3 4 1 2 3 4
50.0
5 6 7 8 5 6 7 8
CSM-

55.0 100.0 OUTPUT OUTPU T

●
 OUTPUT RANGE PROGRAMMING 3 Phases ( Self Powered )
Current Input: INPUT
DMT-AL/VL

OUTPUT Dip Sw itc h A B C

1 2 3 4 5 6 7 8 Ak Al Bk Bl Ck Cl
0 ~ 1 mA on 1 2 3 4 5 6 7 8
0 ~ 10 mA on on
0
4
~2 0 m A
~ 20 mA on
on
on
on
on
9 10 11 12 13 14 15 16
0 ~1V on on on on
0 ~5V on on on A B C
0 ~ 10 V on on OUTPUT
CSM-321S CSM- CSM-321S CSM- CSM-321S CSM- CSM-321S CSM-

1 ~5V on on on on
2 ~ 10 V on on on
Voltage Input: INPUT
* Pads: blank fields mean open.
A B C
Pa ± Pb ± Pc ±

 CONNECTION DIAGRAM 1 2 3 4 5 6 7 8
● 1 Phase ( Auxiliary Powered ) 9 10 11 12 13 14 15 16
Current Input: Voltage Input:
A B C
OUTPUT
A UX. POWER AUX. POWER

Ak
INPUT
Al
INPUT
±
● 1 Phase ( Loop Powered )
P
1 2 3 4 1 2 3 4 Current Input: Voltage Input:
INPUT INPUT
5 6 7 8 5 6 7 8 Ak Al P ±
1 2 3 4 1 2 3 4
OUTPUT OUTPUT
5 6 7 8 5 6 7 8
● 3 Phases ( Auxiliary Powered )
Current Input: OUTPUT OUTPUT
INPUT AUX. POWER
A B C
Ak Al Bk Bl Ck Cl

1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
A B C
OUTPUT

Voltage Input:
INPUT AUX. POWER
A B C
Pa ± Pb ± Pc ±

1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
A B C
OUTPUT

 MODEL INFORMATION
DMT-AL 1 PHASE 2 WIRE CURRENT
DMT-VL 1 PHASE 2 WIRE VOLTAGE

DMT-A3 3 PHASE 3 WIRE CURRENT

DMT-V3 3 PHASE 3 WIRE VOLTAGE

DMT-AL/VL