õUNGHEINRICH System messages 12.

10 1 G
System Messages
Error Description Component Display text Cause / Action Effect
1 Low voltage during F, H, L, Low voltage Check battery voltage, chargebattery; Travel is inhibited.
system start F-AC, H-AC Checkwireconnectiontocontroller;
ELECTRICAL check main current fuse; check main Reduced power for
SYSTEM contactor; replace control part; travel and lifting.
Replacecomponent; Warning symbol
(Limit VN = 80V: VBatt < 64V or flashing (Else-Check).
VCap. < 56V
Limit VN = 48V: VBatt < 34V or
VCap. < 34V
Limit VN = 24V: VBatt <17V)
2 Overvoltage F, H, L, Overvoltage Check battery voltage; replace No travel or hydraulic functions
F-AC, H-AC BATTERY controllerpart; replace component; Warning symbol
CONTROLLER (Limit VN = 80V: VBatt > 92 V flashing (Else-Check).
Limit VN = 48V: VBatt > 62 V
Limit VN = 24V: VBatt > 28 V)
3 Temperature limit for F, H, L, TEMPERATURE Check sensor and wire connections Reduced power for
controllers F-AC, H-AC CONTROLLER Allow controllers to cool down; check travel and lifting.
> 80°C (>70°C fan operation, improve cooling. Warning symbol
MP1510C) or Warm up the controller and operate at flashing (Else-Check).
ACS only: reduced level until the controller has
Info at > 85°C warmed up.
Err at > 115°C
Err at < -20°C
4 Emergency Disconnect F POWER SUPPLY Warning Brake applies, travel inhibited
applied during travel (V < 20V MP1510C)
 õUNGHEINRICH System messages 12.10 2 G

Error Description Component Display text Cause / Action Effect

5 Overvoltage F, F-AC, H-AC ELECTRICAL Check wire connection to battery, Brake applies, travel inhibited
SYSTEM checkBattery, replacecontroller part;
Replace component;
(Limit for Retrak: VBatt > 62 V
Limit for MP1510C: V > 32 V)
6 Wire breakage: C, I2, I3, I4, I5, TRAVEL SWITCH Check wire connection; Travel stop. “Warning” symbol flashes
- Travel setpoint device Travel switch Replace travel setpoint device; (Else-Check). Hydraulic functions
Replace Canion/ Interface; possible
7 Key switch applied F,F-AC,H-AC KEY SWITCH Warning Brake applies, travel inhibited
duringtravel (V < 13V for 200ms MP1510C)
8 2 travel directions applied F-AC, H-AC, C, ELECTRICAL Warning, replace travel direction Travel stop. “Warning” symbol
simultaneously MP, S, I2, I3, I5, SYSTEM switch, replace Interface 7 Canion; flashing (Else-Check).
FS replace Multipilot / Solopilot Hydraulic functions possible
For twin pedal, check the electrical
system.
9 Operator protection I2, FS ELECTRICAL Check switch, check wire connections
switch faulty SYSTEM
10 V Cap. <> V Batt; (main F, H, MAIN CONTACTOR Check main contactor, check wire No travel, hydraulics
contactor jammed or not F-AC, H-AC connection; check output pin 2 (ACS) Warning symbol
open) L of traction controller; replace Flashing warning (Else-Check).
component
11 Offset error armature / F, H, L, CONTROLLER Check main current wire, replace Travel no function
field current (DC) F-AC, H-AC component
Stator current (AC);
Current measurement
point
 õUNGHEINRICH System messages 12.10 3 G

Error Description Component Display text Cause / Action Effect

12 Disable driver field F, H CONTROLLER Replace component; No travel, hydraulics
rheostat faulty for DC F-AC, H-AC for AC: Check flat belt wire connection; Warning symbol
Disable driver power L replace power part Flashing warning (Else-Check).
stage faulty (forAC)
13 Disable Watchdog field F, H CONTROLLER Replace components Travel no function
faulty
14 - Main contactor F, H, CONTROLLER/ Check wire connection; check main No travel, hydraulics
notclosed F-AC, H-AC MAIN CONTACTOR contactor; check charging connection, Warning symbol
- Field power stage Check field supply fuse, Flashing warning (Else-Check).
cannot be switched on Replace component.
(DC)
15 Disable field faulty; F, H, CONTROLLER Replace controlpart; replace Travel no function
Illegal address (for AC) F-AC, H-AC component
L
16 Disable driver armature F, H, CONTROLLER Replace controlpart (AC); replace Travel no function
actuator faulty; F-AC, H-AC component
Software reset (for AC)
17 Disable Watchdog F, H CONTROLLER Replace components Travel no function
armature faulty
18 DC: Armature power F, H, F-AC, H- CONTROLLER Check armature wire connection; Travel no function
stage cannot be switched AC replace power part; replace
on L component
AC: one of the 3 phases
cannot be switched on
 õUNGHEINRICH System messages 12.10 4 G

Error Description Component Display text Cause / Action Effect

19 Disable armature faulty; F, H, F-AC ,H- CONTROLLER Replace power part; Replace Travel no function
Power stage short circuit AC, component.
(for AC) L-AC Can occur in connection with error 70,
The error may be in this case:
triggered by the faulty check power supply behind the main
speed sensor in contactor contact, in the event of an
connection with error the voltage will be much lower
AS4814Plus controllers. here than the rated operating voltage.
Sensor wheel wobbles Disconnect the positive supply from
(elliptical) or the sensor- the components to target the error
sensor wheel gap is too cause. The exception here is the F1
big. In this case the traction controller which must remain
component is not faulty. connected. One component overloads
A short circuit cannot be the testing voltage due to internal short
resolved by switching the circuit.
truck off/on. The testing voltage arises by charging
the internal capacitor batteries via a
resistor to the level of the control
voltage supply.

Check sensor, replace sensor and / or

sensor wheel.
20 Armature incorrectly F, H ELECTRICAL Check armature main current wire Travel no function
connected SYSTEM connection
21 Armature overvoltage F, H, F-AC, H- CONTROLLER/ Check main current wire to armature;
(short circuit / high side AC ELECTR check settings (for AC); check speed
faulty) L sensor (for AC); check static charge
(for AC);
AArmature > 360A for 250ms (MP1510);
Replace component.
 õUNGHEINRICH System messages 12.10 5 G

Error Description Component Display text Cause / Action Effect

22 Watchdog error; F, H, L, M, S, A, CONTROLLER/ Truck reset, No travel, hydraulics
Watchdog does not run I2, I3, I4, C, CANION Replace controlpart; replace Warning symbol
out F-AC, H-AC, FS component Flashing warning (Else-Check).
23 - Computer overload F, H, L, M, S, A, CONTROLLER / CAN Check CAN bus connection; No travel, hydraulics
- Permanent interrupt I2, I3, I4, C, Check CANION connector and Warning symbol
- “ACS” timeout on F-AC, H-AC, FS component; Flashing warning (Else-Check).
CAN connection Replace component
24 EEPROM cannot be F, H, L, I2, I3, I4, CONTROLLER/ Check battery cable; check VBatt; set Flashing warning symbol (Else-
contacted / parameters C, CANION trucktype, set default parameters; Check).
not plausible / parameter F-AC, H-AC replace control part; replace
set to default MFC brake component
Faulty checksum MFC hydr. , Delete logbook, change parameters,
travel switch set hourmeter, replace component
25 No telegrams: F, H, I4, I8 INTERFACE / CAN Check CANBus connection, check
- no logon from F-AC, H-AC wire connection between proportional
interface L valve – modulation; check fuse 1F8;
replace iInterface (I2, I4, I8) ; replace
lift potentiometer, Multipilot, Solopilot
or interface;
MP1510C: Voltage collapses,
controller logs on again, interface does
not, controller remains blocked and
waits for interface.
Check battery voltage (with load!);
charge or replace battery if necessary;
AS2409K: no “live” telegram received
- no telegrams from from CAN Bus travel switch for more
Can-Bus travel switch than 300 ms; replace travel switch
 õUNGHEINRICH System messages 12.10 6 G

Error Description Component Display text Cause / Action Effect

26 Wire breakage: M, S, I2, I3 MULTIPILOT / Check wire connection Lift stop. “Warning” symbol flashes
- Lift potentiometer SOLOPILOT / LIFT (Else-Check), travel enabled
POTENTIOMETER
27 Wire breakage: C, L, I3, I4 STEER ACTUAL Check wire connection; Crawl speed,
- Steering setpoint ANGLE Replace steer angle sensor / Flashing warning symbol (Else-
device; potentiometer; Check), hydraulic functions enabled.
→Reach truck: for 45° Replace Canion / Interface; This error produces an emergency
steering bolster Replace steering; stop on the reach truck and the
movement no flank from Juniors.
proximity switch. PM2402L from software version 1.60:
→Canion: “Steer angle set parameter P511 “operating mode”
acquire active” parameter correctly →1 = analog sensor
has incorrect value (potentiometer),
→Juniors PM2402L: 2 = digital sensor on steer motor
“Operating mode”
parameter incorrectly set
28 Wire breakage: C, L, I3, I4 STEER NOMINAL Check wire connection, replace Crawl speed,
- Steering sensor ANGLE steering wheel sensor;replace Canion Flashing warning symbol (Else-
/ interface; replace steering Check), hydraulic functions enabled.
This error produces an emergency
stop on the reach truck
29 Wire breakage: M Traverse nominal value Replace Multipilot
- Traverse potentiometer MULTIPILOT
30 Wire breakage: M Tilt nominal value Replace Multipilot,
- Tilt potentiometer MULTIPILOT Teach Multipilot (Hall sensor 2003
only)
 õUNGHEINRICH System messages 12.10 7 G

Error Description Component Display text Cause / Action Effect

31 Wire breakage: M, S Sideshift nominal value Replace Multipilot / Solopilot, Hydraulic functions stop, “Warning”
- ZH1 setpoint device MULTIPILOT / Teach Multipilot (Hall sensor 2003 symbol flashes (Else-Check), travel
SOLOPILOT only); enabled
- Initial lift / lower Travel switch
Setpoint device Travel switch: Check / replace switch
32 Wire breakage: M, S MULTIPILOT / Replace Multipilot / Solopilot, Hydraulic functions stop, “Warning”
- ZH2 setpoint device SOLOPILOT Teach Multipilot (Hall sensor 2003 symbol flashes (Else-Check), travel
only) enabled
33 Wire breakage: M, I8 MULTIPILOT Replace Multipilot
- ZH3 setpoint device
34 CANBus damaged F, H, L, M, S, A, CAN-BUS Check CAN bus connection; No travel, hydraulics
I2, I3, I4, I5, C, replace faulty component; Warning symbol
F-AC, H-AC Check terminal resistances Flashing warning (Else-Check). Only
Travel switch stored in logbook (from 2004).
35 No travel zero position I2, I3, I4, C TRAVEL ZERO Warning, check travel switch; Travel stop,
Deadman and Travel switch POSITION Intermittent contact in interface power Flashing warning symbol (Else-
accelerator pedal applied supply (12 volts) Check), hydraulic functions enabled.
when truck switched on Check Canion, for twin pedal check
electrical system
36 No lift zero position M, I2, I3,FS LIFT ZERO POSITION Warning, check lift setpoint device. Hydraulic functions stop, “Warning”
symbol flashes (Else-Check), travel
enabled
37 No steering angle L CONTROLLER / CAN Check steering setpoint device;Check
nominal value CANBus connection; check “steer
type” parameter; Replace component
(I5)
 õUNGHEINRICH System messages 12.10 8 G

Error Description Component Display text Cause / Action Effect

38 Component does not log F, H, L, I2, I3, I4, CONTROLLER / CAN Check CAN-Bus connection and No travel, lifting
on, self test not C, A, M, S, F- voltage; check DIL switch 7 encoding Warning symbol
concluded. AC, H-AC (MP1510); steering controller Flashing warning (Else-Check).
monitoring activated? (AS2412F);
check ACS encoding; replace
component
39 Implausible truck type F, H, L, I2, I3, I4, TRUCK TYPE For 1. Set truck type;
1. Discovered during the I5, A, M, For 2. Examine and if necessary
self test phase that at F-AC, H-AC replace switch (key switch) or rectify
least one component intermittent contact in power supply
has a different truck plug connections.
type as a parameter. Set truck type.
A different truck type was
discovered in operating
mode. Caused by
intermittent contacts in
the power supply
connections
40 Motor overtemperature L, F, H TEMPERATURE Warning; check motor sensor system Reduced power for
Traction motor F-AC, H-AC MOTOR and wire connections; travel and lifting.
overtemperature in Check motor; traction motor brake Warning symbol
operating mode.> 150°C open? flashing (Else-Check). For steering
And travel speed < 1km/h only
For ACS: warning symbol flashing.
Info > 145°C
Err > 165°C
 õUNGHEINRICH System messages 12.10 9 G

Error Description Component Display text Cause / Action Effect

41 Brake magnet L BRAKE Check potentiometer; check
potentiometer MAGNETPOTENTIOM potentiometer attachment; check wire
Potentiometer voltage ETER connection
less than 0.3 volts or
greater than 2.7 volts for
more than 500ms.
42 - Short circuit between L,F BRAKE MAGNET Check wire connection, check brake
the output and battery magnet; replace component
positive.(EJC, ELE)
-Brake magnet control,
below minimum
difference on
potentiometer for 500 ms
when magnet applied.
(150mV )
No brake pressure during
initialization.
Brake pressure after the
Emergency Stop magnet
has applied;
43 Adjust brake L ADJUST BRAKE Adjust brake; check potentiometer
 õUNGHEINRICH System messages 12.10 10 G

Error Description Component Display text Cause / Action Effect

44 -Brake not connected or L,F BRAKE FAULTY -Check brake wiring, replace brake if No release
connection wire short necessary
circuit -Replace brake cable, check
potentiometer; Check potentiometer
-Brake cable torn attachment;
Only for steer
category_3: Only for steer category_3:
Internal driver of failsafe -Check brake driver output, check
brake cannot connect the switch contact plausibility,
relay Replace steer component.
Or short circuit bypass
(contact jams) on the
output during power up
test
45 Too many pulses from L,I5 STEERING WHEEL Check wire connection, replace sensor
steering setpointdevice bearing; replace component
Intermittent contact or
perturbing radiation.
More than 255 pulses
identified within 100ms
46 Steering setpoint L,I5 STEERING WHEEL Check sensor bearing connection;
devicewrongly connected check wireconnection
AS4803L: More than 3 AS4803L: Check steering wheel
pulses identified in one recognition input.
direction and more than 3
pulses in another within
100ms.
 õUNGHEINRICH System messages 12.10 11 G

Error Description Component Display text Cause / Action Effect

47 No pulses from steer L,I5 STEERING WHEEL Check wire connection, replace sensor No release
setpointdevice bearing; replace component
ETVQ steering wheel no
pulses from 1st sensor
bearing.
More than 10 pulses
were obtained from the
stepper motor but fewer
than 3 pulses were
counted within 200ms
from the sensor bearing.
48 Does not match the L STEERING TYPE Set steering type correctly
"Steering type" parameter ETVQ: Check stepper motor coupling,
ETVQ steering wheel no tighten grub screw.
pulses from stepper
motor or 2nd sensor Test both setpoint device branches,
bearing. set defaults and truck type
More than 10 pulses Otherwise faulty, replace component.
were obtained from the
sensor bearing but fewer
than 2 pulses were
counted within 200ms
from the stepper motor
sensor bearing.
49 CAN supply interrupted; AS 2412 Can Bus Suply on CAN connector greater than Travel disabled
Supply above 14 volts or F,H-AC CAN supply 14 volts (electrical system short circuit,
less than 10 volts, Can or component)
sensor bearing
incorrectly supplied
 õUNGHEINRICH System messages 12.10 12 G

Error Description Component Display text Cause / Action Effect

50 NRG Multipilot wire M Setpoint device Check Multipilot wire connection Travel and lifting disabled.
breakage horizontal Parameter 540 set to 1 by mistake
Horizontal tilt
51 Teach-In: steering actual L Incorrect setting Repeat calibration, check wire
value potentiometer SETTING connection;check
potentiometer;replace component
52 Teach-In: Brake magnet L Incorrect setting Repeat calibration, check wire
potentiometer SETTING connection;check
potentiometer;replace component
53 Teach-In: Steering L Incorrect setting Repeat calibration, check wire
setpoint potentiometer SETTING connection;check
potentiometer;replace component
54 Motor wire breakage L, F, H MOTOR WIRE Check wire connection;
during power-up test BREAKAGE Check temperature sensor lines;
ETVQ: Temperature replace component; replace motor
voltage level less than
0.3 volts or greater than
2.7 volts
55 Motor short circuit; L, F-AC, H-AC SHORT CIRCUIT Check wire connection; Traction motor stops,
Current not ok; MOTOR Replace motor; Hydraulic motor stops
Power stage faulty Replace component Warning symbol
flashing (Else-Check).
56 Motor or actual value L,F.H MOTOR REVERSE Check motor connection; check actual
transmitter incorrectly POLARITY value transmitter potentiometer; AC:
connected Phases L1,L2 or L3 swapped on
motor;
 õUNGHEINRICH System messages 12.10 13 G

Error Description Component Display text Cause / Action Effect

57 No actual value change L,F,H Steering controller Check motor; check actual angle
Motor turns despite ACTUAL VALUE potentiometer; rectify mechanical
control signal TRANSMITTER wheel block;
AS4803L: Check incremental
bearings; replace component;
Check actual value transmitter wire
breakage signals
PM2402L check operating mode
58 Steering angle actual L STEER ACTUAL Check actual value transmitter (on
value fluctuates ANGLE steer motor)
ETVQ: Reference mark Check steer motor, fuse and
0° could not be started incremental bearing,
within 5 seconds or no rectify mechanical wheel block;
valid segment reached. Check proximity switch distance.
Steer motor does not turn
59 Steering angle nominal L Steer angle setpoint Check setpoint device potentiometer
value fluctuates device (on tiller)
TILLER
POTENTIOMETER
 õUNGHEINRICH System messages 12.10 14 G

Error Description Component Display text Cause / Action Effect

60 Swivelling bolster does L STEERING CONTROL Check steering bolster mechanics;
not follow steering wheel check chain and chain tension; check
directions motor; check actual value transmitter
Deviation of > 15° for attachment;
100ms Check tyres, replace wheel if
The wheel turns more necessary.
than 5° without change of
nominal value on steering
wheel, less than 2°/sec
after reaching the
nominal position.
Tyres over-tensioned, the
actual value cannot follow
the nominal value.
61 Power stage error L CONTROLLER Replace controller
62 Power stage error L CONTROLLER Replace controller
63 Sensor power supply out L,F-AC,H-AC CONTROLLER The 12 volt supply not in valid range.
of range Monitoring of 12 volt sensor supply
greater than 15 volts and less than 11
AS4803L: < 10V oder volts.
>16V Switch controller off and on, replace
fuse and controller if necessary.
64 Software version differs L CONTROLLER Different software versions in the
AS4803Ls in the ETV-Q. Update
software to same level.
65 NRG Multipilot wire M Centre switch Check Multipilot wire connection Travel and lifting disabled.
breakage centre shifter MP centre shifter Parameter 540 set to 1 by mistake
 õUNGHEINRICH System messages 12.10 15 G

Error Description Component Display text Cause / Action Effect

66 NRG Multipilot wire M 180-360 switch Check Multipilot wire connection Travel and lifting disabled.
breakage MP toggle switch 180°/ Parameter 543 set to 1 by mistake
180° / 360° steering 360°
toggle
67 NRG-Multipilot setpoint M Travel direction Check Multipilot switch, values in Judit Travel and lifting disabled.
device travel direction MP setpoint device MP teach window, recalibrate values
switch jams on MP when
system starts
68 Safety switch wire I2, I3, I4, I5 DEADMAN Check wire connection to safety switch
breakage (deadman, seat switch); replace safety
switch
69 Both lift and lower I2, I5, FS LIFT/LOWERSWITCH Check wire connection; check switch
requested simultaneously
70 Component fails to F-AC, H-AC, M, SELF TEST Check displays on basic component No travel, hydraulics
respond orresponds S, A, (LED); note other error messages on Warning symbol
incorrectly to self test I2, C basic card; Check Flashing warning (Else-Check).
wireconnectionsandcheck connector;
check power supply behind the main
contactor contact, in the event of an
error the voltage will be much lower
here than the rated operating voltage.
Disconnect the positive supply from
the components to target the error
cause. One component overloads the
testing voltage due to internal short
circuit.
The testing voltage arises by charging
the internal capacitor batteries via a
resistor to the level of the control
voltage supply.
 õUNGHEINRICH System messages 12.10 16 G

Error Description Component Display text Cause / Action Effect

71 Lower potentiometer wire I2, FS LOWER Check wire connection; replace lower
breakage POTENTIOMETER potentiometer; replace Multipilot;
replace interface
72 No lowering zero position I2, FS LOWER Warning, check lower setpoint device
RESTPOSITION
73 Valve output interface I2 VALVE OUTPUT Warning, check valve outputs
faulty
74 Interface valve output I2 INTERFACE FAULTY Replace interface
faulty
75 Proportional valve does I2,I4,C PROP. VALVE Check wire connection, replace Flashing warning symbol (Else-
not draw any current proportional valve;replace Canion / Check).
Correct Multipilot ?? interface; replace proportional valve
76 Proportional valve short I2, I4C PROP. VALVE Check wire connection, replace Flashing warning symbol (Else-
circuit proportional valve;replace Canion / Check).
interface; replace proportional valve
77 Button wire breakage I2, BUTTON WIRE Check wire connection; replace button;
BREAKAGE replace interface
78 Button and travel switch I2 BUTTON / TRAVEL Warning: Check wire connection;
pressed simultaneously SWITCH replace button; replace interface
79 Switch and deadman I2 BUTTON / DEADMAN Warning: Check wire connection;
switch pressed replace button; replace interface
simultaneously
80 2 travel directions I2 ELECTRICAL Check wire connection; replace button;
simultaneously SYSTEM replace interface
81 Different parameters for F, F-AC MOTORS reset parameters (EFG traction Travel inhibited
the two traction controllers)
controllers
 õUNGHEINRICH System messages 12.10 17 G

Error Description Component Display text Cause / Action Effect

82 Sensor wire breakage I2 ELECTRICAL Safety height: Check wire connection;
SYSTEM replace button; replace interface
83 2 of the same F, H, I4, F-AC ELECTRICAL Check component encoding; check Travel inhibited
components report on L-AC SYSTEM wire connection; replace component;
thetruck
e.g. AS4803L: Key switch
voltage cannot be
assigned to components
Elle_1,Elle_2 or Elle_3
84 Faulty speed sensor: F,H,L-AC SPEED Check speed sensor; Travel stop,
→AS4803L: SENSOR Sensor bearing drift; Lift stop,
- Speed changes by 50% Check wire connection; Flashing warning symbol (Else-
within 4ms; Replace speed sensor; Check), hydraulic functions enabled.
- Reference speed less Replace component;
than half the rated speed;
- Steer transmission
blocked;
- Tear identification: a
valid sensor reading is
reduced to zero within
4ms and remains at this
level for 50ms without
producing a new valid
reading.
→PM2402L/2 from
V1.60: Check wire routing, do not route
- Too many pulses on together with motor supply wires!
encoder 3 on steer motor
 õUNGHEINRICH System messages 12.10 18 G

Error Description Component Display text Cause / Action Effect

85 Power release low F,H-AC ELECTRICAL Switch truck on and off; check battery; Travel, hydraulics no
voltage L-AC SYSTEM check battery cable connections; function, warning symbol
Travel/Steer: TRAVEL check fuse; Flashing warning (Else-Check).
Capacitor voltage drops Check power connections; replace
to 30V (48V) for 0.5 component
seconds
86 Improbable speed, sud- F,H-AC IMPROB. SPEED Check wire connection; replace speed
den change: L-AC sensor; replace component;
→ AS4803L: 2 sensor
systems differ from each Z Are the pulse figures correct
(8 or 64 pulses/revolution)?
other (actual value trans-
mitter)
Improbable speed, sud- L IMPROB. SPEED Check wiring and plug connections,
den change: check wire routing (do not route
→ PM2402L/2 from together with motor supply wires);
V1.60: PM2402z: actual replace sensor
value transmitter on the
steer motor provides
faulty signals
87 Sensor line interrupted F-AC Electrics Sensor wire disconnected, motor
AS4803L: no voltage L-AC DISCONNECTION consumes maximum current and
drop on a 100 Ohm MFC brake SENSOR BEARING makes buzzing noise. Check sensor
internal measurement wires.
resistor
MFC brake: load wheel
speed sensing
88 Hydraulic speed sensor H SPEED Check speed sensor; Hydraulics stop,
faulty on AS4814H (AS4814H) SENSOR H Check wire connection; replace speed Flashing warning symbol (Else-
sensor; replace component; Check), travel enabled.
 õUNGHEINRICH System messages 12.10 19 G

Error Description Component Display text Cause / Action Effect

89 Hydraulics power release H ELECTRICS- Check battery, check battery wire Reduced power for
low voltage HYDRAULICS connection; travel and lifting.
Check fuse; replace component Warning symbol
flashing (Else-Check).
90 Travel with handbrake on C ELECTRICAL Check magnetic brake switch Flashing warning symbol (Else-
SYSTEM Check).
91 24 volts out of range C ELECTRICAL Check power supply; check wire For a warning, only the warning
Info at <17 V SYSTEM connection symbol flashes (Else-Check).
Err at <15 V For an error, the truck stops.
92 Wrong component M, S, A ELECTRICAL Check Master/Solopilot; check display; Travel, lifting
reporting on Canion SYSTEM replace component function, warning symbol
Check jumper in XB 27 and XB 44 flashes (Else-Check).
from
pin 2 to pin 6,
93 ACS capacitors not F, H, C ELECTRICAL Check charging connection, main Travel, lifting no
charged SYSTEM contactor does not apply, check bus function, warning symbol
voltage, check transformer, fuses and flashes (Else-Check).
cable set,
Replace component
94 SDO error F, H, C SDO ERROR Software incompatible Travel, lifting no
check software version function, warning symbol
Reload software. Check jumper in flashes (Else-Check).
XB 41 from pin 12 to pin 13.
95 Pin code error C PIN CODE ERROR Component pin codes not identical Travel, lifting no
function, warning symbol
flashes (Else-Check).
 õUNGHEINRICH System messages 12.10 20 G

Error Description Component Display text Cause / Action Effect

96 No zero position for M,S Hydraulics zero Check Master/Solopilot; lift, lower, tilt, Hydraulic functions stop, “Warning”
hydraulics position ZH1, ZH2, ZH3, horn switch not in symbol flashes (Else-Check), travel
Masterpilot, Solopilot, MP/SOLOPILOT zero position enabled
Replace component
97 Segment beyond L FAULTY SEGMENT Segment on swivelling bolster not
tolerance limits within tolerance level.
→PM2402L/2 from
V1.60: Check wiring and proximity switch,
Referencing error on check distance from switch to trip
power up, no switch cam on swivelling bolster
signal from proximity
switch (NS) or time
interval exceeded
 õUNGHEINRICH System messages 12.10 21 G

Error Description Component Display text Cause / Action Effect

98 The position of the L POSITION Check wiring.
sensor bearing and DEVIATION
proximity switch
(segment) deviate by
more than 1.1 degrees.
When the truck starts
up, the direction of
rotation from the
steering wheel sensor
system to the motor
power connection or
the steer motor sensor Check wiring and proximity switch,
system is inversed. check distance from switch to trip
→PM2402L/2 from cam on swivelling bolster
V1.60:
Referencing error
during operation,
unexpected switch
signal from proximity
switch.
99 CANBus damaged; F,H,M,S,A, CAN-BUS Check wire connection, check Travel, hydraulics no
CANBus driver I3, I4, C terminal resistors, install truck anti- function, warning symbol
temporarily deactivated interferencemeasures; flashes (Else-Check).
100 NRG software versions M Multipilot software Replace component part with
of internal component corresponding component, as
parts flashing currently not possible in
implausible the field.
 õUNGHEINRICH System messages 12.10 22 G

Error Description Component Display text Cause / Action Effect

101 Input / output error ISM ISM input/output Check I/Oa, rectify contact error, check Shown in the driver’s display with
operating voltage, replace external error 101
transmitter
Index info in display:
a--- Sensor 1 supplies values, but not
defined. Check parameters 11-17
b--- Sensor 2 supplies values, but not
defined. Check parameters 20-26
c--- Sensor 3 supplies values, but not
defined. Check parameters 29-35
Or a sensor 1-3 supplies a voltage
outside the range of 0.5V – 9.5V.
102 Internal error ISM ISM internal Check operating voltage. Shown in the driver’s display with
Index info in display: error 102
a --- Communication between access
module and data recording faulty,
check connection
e --- Radio module faulty
f --- Radio channel number is “0”,
should be >0, check parameter 100
g --- Radio transmitting power is “0”,
Check parameter 101
h --- Lock number is invalid, replace
access module
i --- Impact sensor faulty, replace data
recorder
 õUNGHEINRICH System messages 12.10 23 G

Error Description Component Display text Cause / Action Effect

103 Parameter error ISM ISM parameters Set parameters Shown in the driver’s display with
Index info in display: error 103
a --- Parameter 5 greater than
parameter 6, should be smaller.
b --- Differential value of parameter 11
is greater than the differential values of
the various stages of parameters 12-
17
c --- Differential value of parameter 20
is greater than the differential values of
the various stages of parameters 21-
26
d --- Differential value of parameter 29
is greater than the differential values of
the various stages of parameters 30-
35
e --- the stages of parameters 12-17 …
f --- the stages of parameters 21-26 …
g --- the stages of parameters 30-35 …
h --- Impact stages of parameters 47-
49 …
i --- Impact stages of parameters 50-52
… …are not in increasing order
EFG: C EFG: EFG: EFG:
Setting error combination ERR 103 Check parameter setting, adjust if No hydraulic functions possible
option ZH modification necessary
and ZH3 toggle switch
function
 õUNGHEINRICH System messages 12.10 24 G

Error Description Component Display text Cause / Action Effect

104 Sensor bearing provides F,H (SENSOR BEARING) Check sensor bearing and wire,
no pulses on system start replace sensor bearing or
up controller
105 Motor temperature gauge F,H,L Temp.Motor Check sensor connection and lines, if
provides incorrect values possible replace sensor, otherwise
Sensor line wire replace the entire motor…
breakage
106 Controller temperature F,H,L Temp. controller Internal error, replace controller.
gauge provides incorrect
values
107 Key switch voltage out of F,H,L Electrics Error in controller connection (Saab No travel
range MFC hydr. connector) on component No lifting
Hardware encoding MFC brake No steering
incorrect Main contactor open
108 Calibration reading F,H (CONTROLLER Internal error, replace controller.
incorrect internal)
109 Brake pedal faulty MFC brake BRAKE PEDAL Brake pedal signals implausible
110 Current output faulty MFC brake CONTROLLER Check outputs for short circuits MFC_Hydr.: no lifting
MFC hydr. MFC_Brake: crawl speed only
MFC option
111 Steering controller is F Steering controller Check steering controller Travel inhibited
monitored by traction Main contactor open
controller for signs of life
telegrams
Traction controller does
not receive these
telegrams.
The Can Bus is
overloaded.
 õUNGHEINRICH System messages 12.10 25 G

Error Description Component Display text Cause / Action Effect

112 Steering controller_2 is F Traction controller Check Can Bus, measure terminal
monitored by traction resistor 60Ohm
controller_1 for signs of
life telegrams
The Can Bus is
overloaded.
113 Lift controller does not H LIFT CONTROLLER Check control voltage
send lift telegrams
114 No traverse distance MFC hydr. Info 32 None Reduced traverse speed until both
reference on power up Traverse reference stops have been reached once.
115 Main contactor F,H,L Main contactor Check wire connection. No truck functions
improbable, ?? improbable If error 19 is also present, disconnect
contacts not closed. Wire the shorted power stage
connection interrupted,
Disconnect the power positive.
faulty main contactor
driver on traction Check driver voltage (switched against
controller negative). If reading OK, check
Driver on AS4803z contactor coil and mechanics.
steering controller faulty. Check AS4803z steering controller,
replace if necessary
116 After software flashing F,H, Info 54 Set truck type and switch truck off / on In the log book only error 116 stands
(field operation), the item MFC brake (wait approx. 35 seconds). as a marker for this process and all
number of the software is MFC prop SET TRUCK TYPE On request, automatically: all parameters can be at default.
implausible and parameters are set to default, the
parameters may also be software item number is set to
implausible. plausible, the log book is deleted, the
hourmeter set to zero and entry 116
made in the log book.
 õUNGHEINRICH System messages 12.10 26 G

Error Description Component Display text Cause / Action Effect

117 Cab position implausible, CANION Cab position Check rotary potentiometer, re-adjust if No TRAVEL release
rotary potentiometer necessary, check 180 degree switch
value does not match 180
degree switch
118 Steering controller L Steering controller Check display on steering controller TRAVEL inhibited, EMERGENCY
reports error STOP activated
119 Weigher button MFC brake Button faulty Check wire and button Weighing interrupted
faulty
120 Weigher pressure sensor MFC hydraulics Sensor faulty Check wire and sensor Weighing interrupted
faulty
121 Battery incorrectly locked F-AC Battery lock ECR: Locking strips stuck? Check No truck functions
CANION proximity switch
EFG D30: For automatic battery
locking only, check the locking/
unlocking sensor system, check
mechanical / hydraulic system.
122 Start up error, MFC brake Check load wheel Set the truck model to rectify this. No travel operations
Magnetic brake wrongly brake connection Warning 54 (set truck model) is issued.
connected. If this does not help, check the load
The truck model does not wheel brake connection. Modification
match the internal brake kits must be provided by the spare
characteristic curve. parts department.
123 Encoding in connector MFH ERR_OPERATING Wrong operating mode: Travel and lifting disabled
does not match MODE_IMPROBABLE check jumpers in connector or replace
multifunction lever multifunction lever
124 Mast reach damping MFC hydraulics Sensor faulty Check wire connection, replace sensor Truck travels at reduced speed
sensor (MVD) - 2
channels improbable
 õUNGHEINRICH System messages 12.10 27 G

Error Description Component Display text Cause / Action Effect

130 Wrong travel direction M, S ERR + node number + Direction switch faulty Travel disabled
error number
131 Faulty communication T, E ERR + node number + E box faulty, Travel disabled
with E box error number CAN-Bus fault
132 Communication with ISM T, ISM ERR + node number + ISM faulty, Travel disabled
faulty error number CAN-Bus fault
133 Communication with T, P ERR + node number + Pluto faulty, Travel disabled
Pluto faulty error number CAN-Bus fault
134 Multi-/Solopilot applied at M, S INF + node number + Multi-/Solopilot moved or button Travel disabled
start error number pressed when truck started up. Switch
off truck, switch on truck without
moving Multi/Solopilot or pressing a
button.
135 Multi-/Solopilot reports an M, S ERR + node number + Check Multi-/Solopilot connections, Travel disabled
error (axle error, error number replace components.
EEPROM error, etc.)
136 Error in operating system T ERR + node number + Read logbook to gain a clearer picture Travel disabled
(API) error number of the error.
137 Error in sensor power T ERR + node number + Power supply overload, Travel disabled
supply + 5 V error number TCU faulty
138 Error in sensor power T ERR + node number + Power supply overload, Travel disabled
supply + 8 V error number TCU faulty
139 Watchdog triggered a T ERR + node number + Timeframe not kept within the Travel disabled
reset within the TCU error number software. Software error.
140 Software error, various T ERR + node number + Error in software, should not occur on Travel disabled
causes error number site. Read logbook to gain a clearer
picture of the error.
 õUNGHEINRICH System messages 12.10 28 G

Error Description Component Display text Cause / Action Effect

141 Initialisation error: at least T ERR + node number + TCU-internal error during parameter Travel disabled
one software module error number exchange.
could not be correctly
initialised
142 Accelerator pedal: T ERR + node number + Broken wire or signal voltage short Travel disabled
voltage error, signal error number circuit to power supply or earth;
voltage too high or too Pedal faulty
low
143 Accelerator pedal: switch T ERR + node number + Broken wire or short-circuit in switch Travel disabled
error, zero position switch error number ports or signal line;
position does not match Pedal faulty
the signal reading
144 Accelerator pedal: teach- T INF + node number + Teach value out of range. Teach-in the Error reported
in error error number accelerator pedal again.
145 Reverse pedal: voltage T ERR + node number + Broken wire or signal voltage short Travel disabled
error, signal voltage too error number circuit to power supply or earth;
high or too low Pedal faulty
146 Reverse pedal: switch T ERR + node number + Broken wire or short-circuit in switch Travel disabled
error, zero position switch error number ports or signal line;
position does not match Pedal faulty
the signal reading,
accelerator pedal and
reverse pedal improbable
147 Reverse pedal: teach-in T INF + node number + Teach value out of range. Teach-in the Error reported
error error number reverse pedal again.
148 Brake pedal: voltage T ERR + node number + Broken wire or signal voltage short Travel disabled
error, signal voltage too error number circuit to power supply or earth;
high or too low Pedal faulty
 õUNGHEINRICH System messages 12.10 29 G

Error Description Component Display text Cause / Action Effect

149 Brake pedal: switch error, T ERR + node number + Broken wire or short-circuit in switch Travel disabled
zero position or end error number ports or signal line;
position switch positions Pedal faulty
do not match the signal
reading; zero position
switch and end position
switch not inter-
compatible
150 Brake pedal: teach-in T INF + node number + Teach value out of range. Teach-in the Error reported
error error number brake pedal again.
151 Steer angle sensor error T ERR + node number + Steer angle sensor faulty, broken wire, Only inching available
error number short circuit
152 Pressure sensor A: signal T ERR + node number + Pressure sensor offers invalid reading Travel only in recovery mode
error error number
153 Pressure sensor B: signal T ERR + node number + Pressure sensor offers invalid reading Travel only in recovery mode
error error number
154 Speed sensor left: signal T ERR + node number + Speed sensor for the left wheel offers Travel only in recovery mode
error error number an invalid signal / phase signal
missing. Broken wire or faulty sensor.
155 Speed sensor right: T ERR + node number + Speed sensor for the right wheel offers Travel only in recovery mode
signal error error number an invalid signal / phase signal
missing. Broken wire or faulty sensor.
156 Speed sensors: recorded T INF + node number + Truck travels too quickly; sensors Error reported
speed is greater than the error number supply too many pulses
max. permitted speed
157 “Forward travel pump” T ERR + node number + Broken wire, short circuit to supply / Travel disabled
pulse width modulation error number earth
(PWM) control valve:
control error
 õUNGHEINRICH System messages 12.10 30 G

Error Description Component Display text Cause / Action Effect

158 “Reverse travel pump” T ERR + node number + Broken wire, short circuit to supply / Travel disabled
pulse width modulation error number earth
(PWM) control valve:
control error
159 “Lower” pulse width T ERR + node number + Broken wire, short circuit to supply / Operating functions inhibited
modulation (PWM) error number earth
control valve: control
error
160 “Lift” pulse width T ERR + node number + Broken wire, short circuit to supply / Operating functions inhibited
modulation (PWM) error number earth
control valve: control
error
161 “Fwd. tilt” pulse width T ERR + node number + Broken wire, short circuit to supply / Operating functions inhibited
modulation (PWM) error number earth
control valve: control
error
162 “Rev. tilt” pulse width T ERR + node number + Broken wire, short circuit to supply / Operating functions inhibited
modulation (PWM) error number earth
control valve: control
error
163 “ZH1 fwd. (sideshift)” T ERR + node number + Broken wire, short circuit to supply / Operating functions inhibited
pulse width modulation error number earth
(PWM) control valve:
control error
164 “ZH1 rev. (sideshift)” T ERR + node number + Broken wire, short circuit to supply / Operating functions inhibited
pulse width modulation error number earth
(PWM) control valve:
control error
 õUNGHEINRICH System messages 12.10 31 G

Error Description Component Display text Cause / Action Effect

165 “ZH2 fwd.” pulse width T ERR + node number + Broken wire, short circuit to supply / Operating functions inhibited
modulation (PWM) error number earth
control valve: control
error
166 “ZH2 rev.” pulse width T ERR + node number + Broken wire, short circuit to supply / Operating functions inhibited
modulation (PWM) error number earth
control valve: control
error
167 “Retarder” pulse width T ERR + node number + Broken wire, short circuit to supply / Report error
modulation (PWM) error number earth
control valve: control
error
168 General pulse width T ERR + node number + Parameter error Travel disabled
modulation (PWM) error error number
169 Release valve operating T ERR + node number + Broken wire, short circuit to supply / Error reported
functions: control error error number earth
170 Travel release valve: T ERR + node number + Broken wire, short circuit to supply / Travel disabled
control error error number earth
171 Parking brake valve: T ERR + node number + Broken wire, short circuit to supply / Error reported
control error error number earth
172 EEPROM: read error T ERR + node number + Error present in at least one EEPROM Error reported
error number assembly. EEPROM may be faulty.
173 Recovery switch: T ERR + node number + The recovery switch was not reset for Travel disabled
recovery function still error number normal operation
active
174 Speed sensors: sensor T ERR + node number + Faulty sensor Travel only in recovery mode
readings from left/right error number
sensor faulty
 õUNGHEINRICH System messages 12.10 32 G

Error Description Component Display text Cause / Action Effect

175 ZH2 / ZH3 toggle valve: T ERR + node number + Broken wire, short circuit to supply / Operating functions inhibited
control error error number earth
176 Diesel engine: Actual ECU ERR + node number + ECU reports invalid actual speed Error reported
speed error error number
177 Diesel engine: Error in ECU ERR + node number + ECU reports invalid coolant Error reported
coolant temperature error number temperature
178 Motor model not set T INF + node number + Service parameter not set for engine Error reported
C error number model. Motortyp setzen. Travel disabled
179 Communication with ECU T ERR + node number + CAN Bus to ECU damaged, Travel disabled
interrupted error number ECU damaged
180 Self test: parking brake T ERR + node number + Parking brake or valve faulty Travel disabled
does not engage error number
181 Self test: at least one T ERR + node number + Pressure sensor faulty Travel disabled
pressure sensor is error number
supplying an invalid
signal reading
182 Self test: recorded feed T ERR + node number + Error in feed pump, Travel disabled
pressure out of range error number Error in hydraulic system
183 Self test: release valve T ERR + node number + Release valve faulty Travel disabled
for travel pump jams error number
when open
184 Self test: release valve T ERR + node number + Release valve faulty Travel disabled
for travel pump jams error number
when closed
185 Self test: pressure T ERR + node number + Pressure sensors installed in wrong Travel disabled
sensors swapped error number positions or connector swapped
 õUNGHEINRICH System messages 12.10 33 G

Error Description Component Display text Cause / Action Effect

186 Self test: Self-test T INF + node number + Motor speed too low, seat switch not Travel disabled
interrupted during error number pressed
execution
Self test: Self test Use JUDIT or switch the truck off and Slow travel
deactivated via JUDIT on again via the key switch to activate
the self test
187 Oil temperature: out of T ERR + node number + Oil temperature sensor faulty; Fan rises
range error number short circuit or broken wire
188 Reservoir sensor: out of T ERR + node number + Reservoir sensor faulty; Error reported
range error number short circuit or broken wire
189 Lift height sensor: signal T ERR + node number + Lift height sensor faulty; Error reported
error error number short circuit or broken wire
Travel mode with self test An error occurred while travelling with Travel inhibited, operating functions
deactivated via JUDIT the self test deactivated. Switch truck inhibited except for lowering
interrupted off and on again
190 Parameter error: T INF + node number + Commission with JUDIT and set Travel and operating functions
Required parameters error number parameters inhibited
were not set during
commissioning
191 Combustion engine: T INF + node number + Error in engine or coolant circuit, Error reported (LED in display,
coolant temperature or error number Check hydraulic oil circuit if required logbook entry)
hydraulic oil temperature
too high
192 Sideshift sensor: teach-in T INF + node number + Teach value out of range. Error reported
error error number
193 Anti-stall engine protec- T INF + node number + Operations requested overload the en- Operating functions inhibited
tion active error number gine: engine speed drops, which would
cause the engine to go out
 õUNGHEINRICH System messages 12.10 34 G

Error Description Component Display text Cause / Action Effect

194 Sideshift centre sensor T ERR + node number + Sideshift centre sensor faulty; short- Travel disabled
reading improbable error number circuit or broken wire
195 ZH2 / ZH3 toggle valve: T ERR + node number + Broken wire, short circuit to supply / Operating functions inhibited
control error error number earth
196 Parameter error: wire T ERR + node number + Wire harness type in truck does not Travel inhibited, operating functions
harness error number match parameter settings. Commis- inhibited except for lowering
sion via JUDIT.
201 Optical sensor faulty Rack height sensor
select
202 Too many reference Rack height Calibration wrong
points during calibration select
203 Sensor evaluation Rack height sensor
improbable select
204 Error when reading Rack height Controller All settings set to default
EEPROM select
205 No Multipilot in truck Rack height MP missing
select
240 Internal process Rack height Controller
interrupted select
250 No height actual value on Rack height The height is invalid for the
job input select warehouse level entered
252 Rack height select Rack height
incorrect select
253 Rotary field implausible – F Controller None, switch truck off/on Main contactor opened
transmission overloaded,
excess load on incline
254 Diagnostics piratry Judit Box None Create authorisation No diagnosis possible
 õUNGHEINRICH System messages 12.10 35 G
Components

A C = 064 Display / Operation (LISA / JULIA)

C = 065 Display / Operation (Else-Check)
C = 066 Display/Operation (CANCode)
C = 067 Display (CANDis)
C = 068 Display/Operation (on board computer)
C=3 Comfort display [CANopen]
C Canion (Atlas Copco) [CANopen]
C=1 - Master
C = 11 - slave
E C=8 Electric switch box (E box) / slave
ECU --- Engine Control Unit (ECU)
F C = 016 Travel (MP1510C / AS2405F / AS2409K / AS2412F)
C = 016 Travel 1 (MP1514F / AS4814Fplus)
C = 017 Travel 2 (MP1514F / AS4814Fplus)
F-AC C = 016 Travel (AS4812/14F)
C=8 ACS Traction (Atlas Copco AC 8011/18, Inmotion) [CANopen]
Travel C = 096 Can-Bus travel switch
switch
H C = 032 Lift (MP1514H / AS4814Hplus)
õUNGHEINRICH System messages 12.10 36 G

H-AC C = 032 Lift (AS4814H)

C=7 ACS Pump (Atlas Copco AC 8011/18, Inmotion) [CANopen]
Rack C = 128 Rack Height Select
height
select
I C = 21 I/O-Board 1 [CANopen]
C = 22 I/O-Board 2 [CANopen]
C = 23 I/O-Board 3 [CANopen]
C = 24 I/O-Board 4 [CANopen]
I2 C = 146 Interface 2
C = 155 Interface 21
C = 156 Interface 71
I3 C = 147 Interface 3
I4 C = 148 Interface 4 = MFC_brake
I5 C = 149 Interface 5
I6 C = 150 Interface 6 = MFC_prop
I7 C = 151 Interface 7
I8 C = 152 Interface 8 = MFC_oprion
ISM C = 069 ISM Access Module
C = 29 ISM Access Module [CANopen]
C = 070 ISM-Data recorder
C = 071 ISM radio module
 õUNGHEINRICH System messages 12.10 37 G

L C = 048 Steer (MP1502L / PM2402L / AS4803L)

C = 048 Steer 1 (AS4803L)
C = 049 Steer 2 (AS4803L)
C = 050 Steer 3 (AS4803L)
C=4 Steer computer [CANopen]
M C = 096 Multipilot / Masterpilot
C=2 Multipilot / Solopilot [CANopen]
MFH C = 096 Multifunction lever (ETR)
P C=3 Pluto armrest with display and keypad
S C = 112 Solopilot / Hand lever
T C=1 Transmission Control Unit (TCU) = Master

Travel setpoint device: travel potentiometer, accelerator pedal

Steering actual value transmitter: steer potentiometer, proximity switch (on steered wheel)

ONLY in 1st generation!

All messages numbered above 100 come from the interface and correspond to message 1- xx -99!
 õUNGHEINRICH System messages 12.10 38 G

Z For more details on warnings and information messages refer to the operating instructions.

Warning / Information Messages

INFO 01 SEAT SWITCH_OPEN
INFO 02 NO_TRAVEL DIRECTION
INFO 03 NO_TRAVEL RELEASE
INFO 04 NO_NOMINAL VALUE
INFO 05 LIFTING OFF
INFO 06 DEADMAN KEY OPEN
INFO 07 START_INCORRECT
INFO 08 PARKING BRAKE
INFO 09 SLOW SPEED
INFO 10 TEMPERATURE DRIVE MOTOR
INFO 11 TEMP_LIFT_MOTOR
INFO 12 TEMP_STEER_MOTOR
INFO 13 BRUSH WEAR OUT_DRIVE_MOTOR
INFO 14 BRUSH WEAR OUT_LIFT_MOTOR
INFO 15 BRUSH WEAR OUT_STEER_MOTOR
INFO 16 DRIVING DISABLE
INFO 17 LIFT END DIS.
INFO 18 SECURITY HEIGHT
INFO 19 DOOR OPEN
INFO 20 AISLE MODE
INFO 21 RESCUE STEERING
INFO 22 STEERING MISSING
INFO 23 DIAGNOSTIC_MODE
INFO 24 SWITCH POWER OFF
INFO 25 TEMP_TRAVEL
INFO 26 TEMP_LIFT
INFO 27 TEMP_STEER
õUNGHEINRICH System messages 12.10 39 G

INFO 28 SPARE_1
INFO 29 DISPLAY SWITCHES THE EXTERNAL
BUZZER
INFO 30 TWIN PEDAL BOTH APPLIED
INFO 31 NO ZERO POSITION
INFO 32 NO TRAVERSE REFERENCE ON POWER UP
INFO 33 ONLY CRAWL SPEED POSSIBLE AS
BATTERY NOT LOCKED
INFO 34 ONLY CRAWL SPEED POSSIBLE, AS INFO
FROM STEERING CONTROLLER
INFO 35 LOW VOLTAGE TRAVEL
INFO 36 LOW VOLTAGE LIFT
INFO 37 LOW VOLTAGE STEER
INFO 40 CHECK MOTOR SENSOR SYSTEM
INFO 48 IMPACT EVENT VERTICAL FORCE 1
INFO 49 IMPACT EVENT VERTICAL FORCE 2
INFO 50 IMPACT EVENT VERTICAL FORCE 3
INFO 51 IMPACT EVENT HORIZONTAL
FORCE 1
INFO 52 IMPACT EVENT HORIZONTAL
FORCE 2
INFO 53 IMPACT EVENT HORIZONTAL
FORCE 3
INFO 54 SET TRUCK TYPE
INFO 55 REVERSE TRAVEL BUTON NOT PRESSED
INFO 56 ERROR FREE LIFT SENSOR
INFO 73 CHECK VALVE OUTPUTS
INFO 90 TRAVEL AGAINST THE HANDBRAKE
INFO 96 NO ZERO POSITION FOR HYDRAULIC
CONTROLS
INFO 97 ERROR HYDRAULICS