Important Questions for Class 10

Science

Chapter 13 – Magnetic Effects of Electric Current

Very Short Answer Questions 1 Mark

1. Magnetic field lines determine

(a) The shape of magnetic field
(b) Only the direction of magnetic field
(c) Only the relative strength of the magnetic field
(d) Both the direction and the relative strength of magnetic field
Ans: (d) Both the direction and the relative strength of magnetic field

2. A device for producing electric current is called a

(a) Galvanometer
(b) Motor
(c) Generator
(d) Ammeter
Ans: (c) Generator

3. At the time of short circuit, the current in the circuit

(a) vary continuously
(b) reduced considerably
(c) increases heavily
(d) does not change
Ans: (c) increases heavily

Class X Science www.vedantu.com 1

4. Figure shows the magnetic field lines between the two faces A and B of two
magnets.

(a) Both faces A and B of two bar magnets are North pole.
(b) Both faces A and B of two bar magnets are South pole.
(c) Face A is south pole while face B is north pole.
(d) None of the above.
Ans: (d) None of the above.

5. The magnetic field near a long straight wire is described by

(a) Straight field lines parallel to the wire.
(b) Straight field lines perpendicular to the wire.
(c) Connective circle centred on the wire.
(d) Radial field lines starting from the wire.
Ans: (c) Connective circle centred on the wire.

6. A current carrying conductor placed in magnetic field experiences a force.

The displacement of the conductor in magnetic field can be increased by
(a) Decreasing the magnetic field.
(b) Decreasing the current in the conductor.
(c) Increasing the magnetic field.
(d) None of the above.
Ans: (c) Increasing the magnetic field.

Class X Science www.vedantu.com 2

7. A positively charged particle say an alpha particle projected towards west
is deflected toward north by a magnetic field. The direction of the
magnetic field is
(a) upward
(b) downward
(c) towards south
(d) towards east
Ans: (a) upward

8. Which of the following properties of a proton can change when it moves

freely in a magnetic field?
(a) mass
(b) speed
(c) velocity
(d) momentum
Ans: (c) velocity and (d) momentum

9. The direction of the magnetic field at a point P above the wire carrying
current as shown in the figure is

(a) Down the page

(b) up the page
(c) into the page
(d) out of the page
Ans: (d) out of the page

Class X Science www.vedantu.com 3

10. Concentric circles with arrows centred at the wire AB are shown in
figure.

(a) No current in AB
(b) current flows from B to A
(c) current – flows from A to B
(d) none of these
Ans: (b) current flows from B to A

11. Electric motor converts

(a) Mechanical energy into electrical energy
(b) Mechanical energy into heat energy
(c) Electrical energy into heat energy
(d) Electrical energy into mechanical energy
Ans: (d) Electrical energy into mechanical energy

12. Potential difference between a live wire and a neutral wire is

(a) 200 volt
(b) 150 volt
(c) 210 volt
(d) 220 volt
Ans: (d) 220 volt.

Class X Science www.vedantu.com 4

13. The most important safety device method used for protecting electrical
appliances from short circuiting or overloading is
(a) Earthing
(b) use of stabilizer
(c) use of electric meter
(d) fuse
Ans: (d) fuse

14. Forces acting on a stationary charge of in the magnetic field B is

(a) BQ v
(b) BQ/v
(c) Bv/Q
(d) Zero
Ans: (d) zero

15. The rectangular coil of copper wires is rotated in a magnetic field. The
direction of induced current change once in each
(a) one revolution
(b) one fourth revolution
(c) half revolution
(d) two revolutions
Ans: (c) half revolution

16. Choose the correct option:

(a) The magnetic field inside a long straight solenoid-carrying current Is
zero.
(b) Decrease as we move towards its end.
(c) Increase as we move towards it end.

Class X Science www.vedantu.com 5

(d) Is the same all points.
Ans: (d) is the same at all points.

17. Name some sources of direct current.

Ans: A cell, a battery, and a D.C. generator are all examples of direct current
sources.

18. The phenomenon of electromagnetic induction is

(a) the process of charging a body.
(b) the process of generating magnetic field due to a current passing through
a coil.
(c) producing induced current in a coil due to relative motion between a
magnet and the coil.
(d) the process of rotating a coil at an electric motor.
Ans: (c) producing induced current in a coil due to relative motion between a
magnet and the coil.

19. The essential difference between A.C. generator and a D.C. generator is
that
(a) A.C. generator has an electromagnet while a D.C. generator has
permanent magnet.
(b) D.C. generator will generate a higher voltage
(c) A.C. generator will generate a higher voltage
(d) A.C. generator has slip rings while the D.C. generator has commentator.
Ans: (d) A.C. generator has slip rings while the D.C. generator has commentator.

20. In which position the force on conductor is maximum when it uniform

magnetic field? is placed in
Ans: When the conductor is parallel to the field

Class X Science www.vedantu.com 6

21. How can it be shown that magnetic field exist around a wire carrying
current?
Ans: By using a magnetic compass that displays deflection.

22. How can a solenoid be used to magnet a steel bar?

Ans: By placing a steel bar into the solenoid and turning on the electricity.

23. Why can’t two magnetic field lines ever intersect?

Ans: If this is the case, there will be two separate magnetic field directions at the
site of intersection, which is not feasible.

24. Can 5A fuse be used in wire carrying 15 A current? Why?

Ans: Because they'd both be useless at managing the quantity of current flowing
if that happened.

25. Give the factors that affect strength of magnetic field at a point due to a
straight conductor carrying current.
Ans: Perpendicular distance between that point and the conductor, magnitude of
electric content.

26. Where do we connect a fuse: with live wire or with neutral wire?
Ans: It is always wired with live electricity.

27. Name any two devices which use permanent magnets.

Ans: Loudspeaker, Motor, Galvanometer, voltmeter.

28. Draw the magnetic field lines representing uniform magnetic field.
Ans:

Class X Science www.vedantu.com 7

29. If the frequency of A.C. is 50 Hz. Then how many times it is changing its
direction in 1 second
Ans: 100 Times will be changing its direction in a second.

30. What is the pattern of the magnetic field lines around a straight
conductor carrying current?
Ans: Concentric circles

31. If the current is flowing in the direction of advancement of screw, then

what is the direction of magnetic field lines?
Ans: Magnetic field will be directed inwards.

32. How can you say that the magnetic field is uniform inside the solenoid?
Ans: Because the field lines inside the solenoid are parallel.

33. Which property of a proton will change while it moves freely in a

magnetic field?
Ans: Momentum or Velocity.

34. According to Flemings right hand rule, which part of right hand indicate
the movement of conductor?
Ans: Thumb

Class X Science www.vedantu.com 8

35. If the no. of turns of a circular current carrying coil are doubled, then
how will the magnetic field produced by it changes?
Ans: Doubled

Short Answer Questions 2 Marks

1. State two properties of magnetic lines of force?

Ans: The two properties of magnetic lines of force are-
i. The strength of the magnetic field is proportional to the closeness of the lines.
ii. They can never cross i.e. the field is unique at any point in space.

2. Why does a compass needle deflect when brought near a bar magnet?
Ans: A compass needle deflected when brought near a bar magnet due to the
magnetic field of the bar magnet.

3. The magnetic field lines in a given region are uniform. Draw a diagram to
represent.
Ans: The magnetic field lines in a given region are uniform when they are
represented in the same direction.

4. Write two ways to induce current in a coil?

Ans: The two ways to induce current in a coil are-

Class X Science www.vedantu.com 9

i. By moving a bar magnet toward or away from the coil current is induced.
ii. By moving a coil rapidly between the two poles of a horseshoe magnet.

5. Draw magnetic field lines around a bar magnet? Give one point of
difference between uniform and non- uniform magnetic field.
Ans: The magnetic field lines around a bar magnet is as follows:

Uniform magnetic field lines are parallel but non- uniform magnetic field lines
are non-parallel.

6. Why do not two magnetic field lines intersect each other?

Ans: If two magnetic field lines intersect each other then there will be two
directions of magnetic field, which is not possible. Thus, they do not intersect
each other.

7. Name and state rule used to determine the direction of magnetic field
produced around a straight conductor carrying current?
Ans: Right hand thumb rule is used to determine the direction of magnetic field
produced around a straight conductor carrying current. It states that if we hold the
current-carrying conductor in our right hand such that the thumb points the
direction of the current, then the direction in which the fingers encircle, gives the
direction of magnetic lines.

Class X Science www.vedantu.com 10

8. What is electric fuse? Where is it connected in a circuit?
Ans: Electric fuse is a safety device which is used to limit the current in an electric
circuit which is made up of a wire made of copper or aluminium or a tin lead
alloy. It is always connected in series at the beginning of the circuit.

9. State the factors on which strength of magnetic field at a point due to a

current carrying conductor depends?
Ans: The factors on which strength of magnetic field at a point due to a current
carrying conductor depends are-
i. It is directly proportional to the amount of current (I) flowing through the
conductor.
ii. It is inversely proportional to the distance (r) from the current carrying
conductor.

10. What is an electromagnet? Write two uses of an electromagnet?

Ans: They are the type of magnet in which the magnetic field is produced by an
electric current i.e. when current is passed through a solenoid it behaves as a
magnet and is called an electromagnet.
The two uses of an electromagnet are-
i. Used in electrical devices like motors, generators etc.
ii. Used to lift heavy iron pieces.

Class X Science www.vedantu.com 11

11. State and define S.I unit of magnetic field?
Ans: The S.I unit of magnetic field is Tesla (T). It states that 1meter long
conductor carrying 1 ampere current experiences 1 Newton force, when placed
perpendicular to the direction of magnetic field then the magnetic field strength
is 1 Tesla.

12. A current carrying conductor is placed perpendicular to the uniform

magnetic field. What happens to displacement of the conductor if
i. strength of current increases
Ans: The displacement of the conductor will increase on increasing the strength
of current.

ii. If horseshoe magnet is replaced by a weak horse shoe magnet.

Ans: The displacement of the conductor will decrease on using a weak horseshoe
magnet.

13. Draw magnetic field around a bar magnet.

Ans: The magnetic field around a bar magnet is as follows:

14. Why don’t two magnetic lines of force intersect each other?

Class X Science www.vedantu.com 12

Ans: If two magnetic field lines intersect each other then there will be two
directions of magnetic field, which is not possible. Thus, they do not intersect
each other.

15. Consider a circular loop of wire lying in the plane of the table. Let the
current pass through the loop clockwise. Apply the right-hand rule to
find out the direction of the magnetic field inside and outside the loop.
Ans: According to the right-hand rule inside the loop, the magnetic field lines are
directed perpendicular to the plane of paper in the inward direction while outside
the loop magnetic field lines are directed out of the plane paper.

16. What is the role of the split ring in an electric motor?

Ans: Split ring is used for reversing the direction of current in the coil. It acts as
a commutator i.e., the direction of current flowing in the motor coil reverses after
half turn, giving rise to a continuous rotation of the coil and the axle.

17. State the principle of an electric generator.

Ans: The principle of an electric generator is electromagnetic induction i.e.,
When a rectangular coil is rotated in a uniform magnetic field, an induced emf is
generated between the ends of the coil.

18. Which sources produce alternating current?

Ans: The sources that produce alternating current are-
● House generators
● Car alternators
● Bicycle dynamos
● Hydroelectric Power Plants
● Thermal power generators
● Nuclear power generators,
● AC generators etc.

Class X Science www.vedantu.com 13

19. Name two safety measures commonly used in electric circuits and
appliances.
Ans: The two safety measures commonly used in electric circuits and appliances
are-
● use of earth wire and proper earthing.
● use of fuse or MCB.

20. State whether the following statements are true or false.

a. An electric motor converts mechanical energy into electrical energy.
Ans: False

b. An electric generator works on the principle of electromagnetic induction.

Ans: True

c. The field at the centre of a long circular coil carrying current will be
parallel straight line
Ans: True

d. A wire with green insulation is usually the live wire of an electric supply.
Ans: False

21. When is the force experienced by a current-carrying conductor placed in

magnetic field largest?
Ans: When the conductor is placed with its length in a direction perpendicular to
that of the magnetic field then the force experienced by a current-carrying
conductor placed in the magnetic field largest.

22. Name some devices in which electric motors are used.

Ans: Electric motors are used in all devices where we want to convert electrical
energy into Mechanical energy. Some devices in which electric motors are used
are-

Class X Science www.vedantu.com 14

● Water pumps
● Computers
● Coolers
● Washing machines etc

23. When does an electric short circuit occur?

Ans: An electric short circuit occurs when the current in the circuit rises rapidly
and the electrical connection draws an excessive amount of current from the
supply it is because if either the insulation of wires used in an electric circuit is
damaged or there is a fault in the appliances, live wire and neutral wire may come
in direct contact.

24. Why is the earth pin thicker and longer than the live and the neutral
pins?
Ans: The earth pin is made longer so that even by mistake it cannot be inserted
into the hole for the live or neutral connection of the socket or it gets connected
to the earth terminal earlier than the live and neutral pins and it is made thicker
so that it does not enter into the live or neutral sockets.

25. A current-carrying straight conductor is placed in the east-west

direction. What will be the direction of the force experienced by this
conductor due to earth’s magnetic field? How will this force get affected?
a. reversing the direction of flow of current
Ans: The direction of earth’s magnetic field is from south to north and if current
is from west to east. Therefore, force is vertically upwards. By reversing the
direction of current, the direction of force will be reversed i.e., vertically
downwards.

b. doubling the magnitude of current

Ans: The direction of earth’s magnetic field is from south to north and if current
is from west to east. Therefore, force is vertically upwards. By doubling the
magnitude of current the magnitude of the force is doubled.

Class X Science www.vedantu.com 15

26. Give two uses of electromagnets.
Ans: The two uses of electromagnets are-
i. Used in electrical devices like motors, generators etc.
ii. Used to lift heavy iron pieces.

27. A straight wire carrying electric current is moving out of plane of paper
and is perpendicular to it. What is the direction and type of induced
magnetic field?
Ans: If a straight wire carrying electric current is moving out of the plane of paper
and is perpendicular to it then the induced magnetic field will be in the form of
concentric circles in the plane of paper.

28. Why does the bulk of iron filings stick to the ends of a bar magnet and
not at its centre?
Ans: Since at the ends magnetic strength is maximum and at canters magnetic
strength is least. Therefore, the bulk of iron filings slick to the ends of a bar
magnet and not at its centre.

29. A student draws three magnetic field lines 1,2 and 3 of a bar magnet with
the help of a compass needle as shown in figure.

a. Is this configuration possible?

Ans: No, this configuration is not possible.

Class X Science www.vedantu.com 16

b. If not, what is
Ans: Because two field lines cannot intersect, and the direction of some field
lines are wrong.

30. Suppose you are sifting in a room facing one of the wall. An electron
beam moving horizontally from your back goes towards the wall in front
you deflected to our left, what is the direction of magnetic field in the
room?
Ans: The direction of the magnetic field in the room will be vertically upward.

31. A current through a horizontal power line flows in north to south

direction. What is the direction of magnetic field directly above it?
i. at a point directly below it and
Ans: The direction of the magnetic field is West to East.

ii. at a point
Ans: The direction of the magnetic field is East to West.

32. Electric appliances like electric -press, toaster, fans etc are connected to
electric mains through three-pin plug. Why?
Ans: Electric appliances are connected to three pin plugs because heavy
appliances require earth wire to prevent short circuiting and to prevent users from
getting shock in case of leakage of any current.

Short Answer Questions 3 Marks

1. What is the function of an earth wire? Why is it necessary to earth metallic

casing of electric appliances?
Ans: The earth wire is used for the safety measures that have green insulation and
is connected to a metal plate deep in the earth near our houses. Appliances like
the electric press, toaster, table fan, refrigerator, etc have the metallic body that
needs to connect to the earth wire this will provide a low resistance path for the.

Class X Science www.vedantu.com 17

Thus, if any leakage of current occurs to the metallic body of the appliance it
keeps potential to that of the earth, and this may prevent the severe electric shock.

2. We know a current-carrying conductor placed in a magnetic field

experience a force due to which the conductor moves. How do we think
the rod displaces if
(a) current in the rod is increased
Ans: Force acting on the current-carrying conductor depends on the strength of
the magnetic field, amount of current flowing in the conductor, and length of the
conductor. Therefore, when the current in the rod increase then the force also
increases hence displacement of the rod increases.

(b) a stronger horseshoe is inserted

Ans: Force acting on the current-carrying conductor depends on the strength of
the magnetic field, amount of current flowing in the conductor, and length of the
conductor. Therefore, when a stronger horseshoe magnet is inserted, the magnetic
field increases. So, force increase. Hence displacement increases.

(c) length of the rod is increased

Ans: Force acting on the current-carrying conductor depends on the strength of
the magnetic field, amount of current flowing in the conductor, and length of the
conductor. Therefore, when the length of the rod increase, force increases, and
hence displacement increases.

3. What is the principle of electric motor?

Ans: Electric motor is a rotating device that can convert electrical energy into
mechanical energy. Which works on the principle that a current-carrying
conductor placed perpendicular to a magnetic field experience a force.
State the function of,
(i) split ring
Ans: It acts as a commutator. The split ring reverses the direction of current
through the coil after every half rotation and thus the direction of force is also
reserved. As a result, the dc motor continues to rotate in the same direction.

Class X Science www.vedantu.com 18

(ii) field magnet used in the electric motor.
Ans: Field magnet used in the electric motor provided a strong magnetic field.

4. State three factors on which magnetic field produced by a current-

carrying solenoid depends.
Ans: The three factors on which the magnetic field produced by a current-
carrying solenoid depends are the strength of the current flowing through the
solenoid, the number of turns of the wire of the solenoid, and the nature of the
material inside the solenoid.

5. What is a solenoid? Draw magnetic field lines showing the magnetic field
inside and outside the current-carrying solenoid?
Ans: A solenoid is a coil that has many circular turns of insulated copper wire,
which are arranged closely in the shape of a cylinder.

6.
(a) Name four appliances wherein an electric motor is used as an important
component. In what respect is it different from a generator?
Ans: The four appliances which have electric motor inside them are Mixers,
washing machines, refrigerators, and blenders. In electric motor electrical energy
is converted into mechanical energy whereas, in an electric generator mechanical
energy is used to produce electricity.

Class X Science www.vedantu.com 19

(b) Define the terms used in the generator
(i) armature
Ans: Armature is a coil of a large number of turns of insulated copper wire wound
over a soft iron core.

(ii) slip rings

Ans: Rings made up of brass that rotates along with the coil and helps in reversal
of the direction of the current.

(iii) brushes
Ans: Brushes are made up of carbon which is pressed against the slip rings and
are connected to an external circuit where output is obtained.

7.
(a) What is the standard colour code followed for
(i) live
Ans: red

(ii) neutral and

Ans: black

(iii) earth wires used in electric circuits?

Ans: green

(b) Which part of an electric appliance is earthed and why?

Ans: The metallic case of an electrical appliance is earthed because metals are
good conductors of electricity and in case of current leakage i.e. live wire touches
the metallic case of an appliance and then due to proper earthing all the excess
amount of current flows down to the earth and thus, we can prevent ourselves
from an electric shock.

Class X Science www.vedantu.com 20

8.
(a) What is short-circuiting?
Ans: Overloading occurs when live and neutral wires come into direct contact, in
that case, the current in the circuit increases abruptly. This is called short-
circuiting.

(b) What is overloading? How can you avoid overloading?

Ans: Overloading means a huge amount of current flows in the circuit. It can
occur when live and neutral wires come into direct contact. It can be avoided by
not using too many appliances in a single socket and by using a fuse in the circuit
which can prevent damage to the appliances and the circuit.

9. Define electromagnetic induction? Two circular coils A and B are placed

close to each other. If the current in the coil A is changed, will some
current be induced in the coil B? Explain.
Ans: Electromagnetic induction is a process by which the production of induced
current in a conductor due to the change in the magnetic field in another
conductor. When the current in first coil A is changed, the magnetic field
associated with coil A also changes. Thus, the magnetic field lines around the
secondary coil B will also change. Hence the change in magnetic field lines
associated with the secondary coil B will induce electric current in it.

10. Why does a current carrying conductor keep in a magnetic field

experience force? What is the direction of force acting on the conductor?
Ans: A current-carrying conductor is kept in a magnetic field experience force.
This is because the electric current that flows through a conductor, produces this

Class X Science www.vedantu.com 21

magnetic field. A force that is equal in magnitude and opposite in direction is
exerted by this magnetic field.

11.
(a) Distinguish between A.C and D.C?
Ans: The difference between AC and DC is listed below:
Alternating current Direct current
AC is safe to transfer long distances DC is not used for long-distance as it
and it can maintain electric power. loses electric power.
The frequency is generally 50Hz or DC has no frequency.
60Hz.
In AC changes its direction. DC has a single direction.

(b) Which source produces alternating current?

Ans: The sources that produce alternating current are AC generators,
hydroelectric power plants, nuclear power generators, and thermal power
generators.

12.
(a) Define the term current rating of an electric fuse?
Ans: The maximum amount of current that can be passed through the fuse wire
without melting it.

(b) Name the material used to make an electric fuse?

Ans: Alloy of Lead and Tin is used to make an electric fuse.

(c) Name two safety measures commonly used in electric circuits and
appliances?
Ans: Electric fuses and earth wire.

Class X Science www.vedantu.com 22

13. Why does a compass needle get deflected when brought near a bar
magnet?
Ans: The compass needle is a small bar magnet. When a compass needle is
brought near a bar magnet, its magnetic field lines interact with that of the
compass needle. Then due to repulsive force between like poles and attraction
between unlike poles, the compass needle is deflected.

14. List the properties of magnetic lines of force.

Ans: Properties of magnetic field lines of force are as follows:
i. Outside a magnet, the field lines are directed from the N-pole of the magnet
towards the S-pole, and inside the magnet, lines are directed from S-pole to
N-pole.
ii. Magnetic field lines are closed curves.
iii. No two magnetic field lines intersect each other.
iv. The density of magnetic lines decreases, when the distance between the poles
increases.

15. In activity 13.7, how do we think the displacement of rod AB will be

affected if
(i) current is rod AB is increased,
Ans: If the current in rod AB is increased then its displacement will also increase.

(ii) a stronger horseshoe magnet is used, and

Ans: If a stronger horseshoe magnet is used then the displacement of rod AB will
also increase.

(iii) length of the rod AB is increased?

Ans: If the length of the rod AB is increased, the force acting on it will increase
hence, displacement of the rod also increases.

Class X Science www.vedantu.com 23

16. State Fleming’s left-hand rule.
Ans: Fleming’s left-hand rule states that stretch the forefinger, the central finger,
and the thumb of your left hand in a way they mutually perpendicular to each
other. If the forefinger shows the direction of the magnetic field and the central
finger that of the current, then the thumb will point towards the direction of
motion of the conductor or the force acting.

17. What is the principle of an electric motor?

Ans: Electric motor is a rotating device that can convert electrical energy into
mechanical energy. An electric motor is based on the principle that the current-
carrying conductor experiences a force when placed in a magnetic field. The
direction of the force is given by Fleming’s left-hand rule, if the direction of the
magnetic field and that of the current are mutually perpendicular.

18. Explain different ways to induce current in a coil.

Ans: If a coil is moved rapidly between the south and north poles of a horseshoe
magnet, relative to a coil the magnet is moved, and By keeping the coil still and
rotating a magnet inside it are the different ways to induce a current in a coil.

19. An electric oven of 2 kW power rating is operated in a domestic electric

circuit ( 220 V) that has a current rating of 5 A. What result do you
expect? Explain.
Ans: The power rating of the electric oven (P)  2 kW
 2 1000  2000W
P
Current drawn (I) 
V
2000
  9.09A
220
The current rating of the domestic electric circuit is given as 5 A and the oven
draws a current of 9.09A . Which is more than the current rating; hence the circuit
will be damaged due to overheating or overloading.

Class X Science www.vedantu.com 24

20. What precaution should be taken to avoid the overloading of the
domestic electric circuit?
Ans: Two separate circuits should be used for domestic purposes, one of 5A
current rating of bulbs, fans, tubes, etc., and the other 15 A current rating for
appliances with a higher current rating such as geysers, air coolers, electric iron,
and stoves, etc. Too many appliances should never be connected to a single
socket. A fuse of appropriate current rating should be used with the electric circuit
for proper safety. These are the precautions we should take to avoid the
overloading of domestic electric circuits.

21. List three methods of producing a magnetic field.

Ans: Three methods of producing magnetic fields are as follows,
● Using permanent magnets or horse-shoe magnets at the place where the
magnetic field is required.
● By using electromagnets
● Using current-carrying conductors or a current-carrying coil.

22. How does a solenoid behave like a magnet? Can you determine the north
and south poles of a current-carrying solenoid with the help of a bar
magnet? Explain.
Ans: The solenoid has a soft iron core with insulated copper wire over it so it can
behave like a magnet. A strong and uniform magnetic field is produced around
the solenoid when a current is passed through it. which is similar to that of the
magnetic field of a bar magnet.
Solenoid behaves like a strong bar magnet. We can determine the poles of
magnets formed by solenoids. The solenoid repels if the north pole of a bar
magnet is brought near the negative terminal of the battery, the same for the south
pole. As we know, poles repel each other.

23. Imagine that you are sitting in chamber with your back to one wall. An
electron beam, moving horizontally from back wall towards the front
wall, is deflected by a strong magnetic field to your right side. What is
the direction of magnetic field?

Class X Science www.vedantu.com 25

Ans: From the problem, it is clear that an electron beam moving horizontally
from the back wall towards the front wall is equivalent to a current flowing in the
opposite direction. The deflection of the electron beam as seen by the observer is
to his right side. Then by applying Fleming’s left-hand rule we find that the
magnetic field is acting in a vertically downward direction.

24. A coil of insulated copper wire is connected to a galvanometer. What will

happen if a bar magnet is
(i) pushed into the coil.
Ans: When a bar magnet is pushed into the coil of insulated copper wire
connected to a galvanometer, the galvanometer gives a deflection towards the left
direction.

(ii) withdrawn from inside the coil

Ans: When the bar magnet is withdrawn from inside the coil, then an induced
current is set in the coil that deflects the galvanometer in the right direction.

(iii) held stationary inside the coil?

Ans: If the bar magnet is held stationary inside the coil, then there won’t be any
induced current so the galvanometer does not show any deflection.

25. Two circular coils A and B are placed close to each other. If the current
in the coil A is changed, will some current be induced in the coil B? Give
reason.
Ans: Yes, If the current in coil A is changed, then some current will be induced
in coil B.
As the two circular coils, A and B are placed close to each other. When the current
in coil A is changed, the magnetic field associated with it also changes. As coil B
is placed near coil A, the magnetic field lines around coil B also change. Due to
changes in magnetic field lines associated with coil B, a current is induced in coil
B.

Class X Science www.vedantu.com 26

26. State the rule to determine the direction of a
(i) magnetic field produced around a straight current carrying conductor
Ans: The direction of the magnetic field produced around a straight conductor
can be determined from the “Right-hand thumb Rule”.

(ii) force experienced by a current carrying straight conductor

Ans: To find the direction of force experienced by a current-carrying straight
conductor placed in a magnetic field we make use of “Fleming’s left-hand rule”.

(iii) current induced in a coil due to its rotation in a magnetic field.

Ans: For finding the direction of current induced in a coil we use “Fleming’s
right-hand rule”.

27. What is the function of an earth wire? Why is it necessary to earth

metallic appliances?
Ans: The earth wires function as a safety measure, especially for those appliances
like heater, electric, press, room cooler, etc that have a metallic body. The metallic
body of the appliance is connected to the earth wire, which provides a low
resistance conducting path for electric current. It ensures that any leakage of
current to the metallic body of an appliance keeps its potential the same as of
earth. As a result, the user is safe from severe electric shock, even if a user touches
the body of the appliance.

28. An electron enters a magnetic field at right angles to it as shown in fig.

The direction of the force acting on the electron will be:
(a) to the right (b) to the left (c) out of the page (d) into the page

Class X Science www.vedantu.com 27

Ans: An electron enters a magnetic field at right angles to it so the direction of
the force acting on the electron will be into the page.
When a conductor carrying current is placed perpendicular to the direction of the
magnetic field, then the direction is given by Fleming’s left-hand rule. According
to Fleming's Left-Hand rule, we know that the direction of force is perpendicular
to the direction of the magnetic field and current. Here, the direction of current
can be taken as the opposite to the direction of motion of electrons. The force
acting on an electron is opposite to that. Therefore, in this case, it is into the page.

29. Consider a circular wire lying in the plane of the table and the direction
current in it is antilock wise.
(i) Draw the magnetic field lines produced around it.
Ans:

(ii) Why does magnetic field at the center of current carrying circular loop
appear straight? Explain with diagram.
Ans: Because of the large curvature of magnetic field lines at centre.

30. If we place a compass needle near straight conductor carrying current

(a) What happens to the deflection of the compass needle if the direction of
current reversed.
Ans: If we place a compass needle near a straight conductor carrying current then
the deflection of the compass needle will reverse if the direction of current is
reversed.

Class X Science www.vedantu.com 28

(b) What change will you notice in the compass needle if it is moved away
from conductor but the current through the conductor remains the
same?
Ans: If we place a compass needle near a straight conductor carrying current
Deflection will decrease in the compass needle if it is moved away from the
conductor but the current through the conductor remains the same.

31. A magnet is moving towards a coil as shown in figure.

(1) Which phenomenon is shown in figure.

Ans: Electromagnetic induction

(2) Which physical quantity is between magnet and coil? set up in the coil
when there is a relative motion
Ans: Induced current

(3) What may be the cause of the production of that physical quantity?
Ans: Change in magnetic lines of forces through the coil

32. Suppose your science teacher asks you to demonstrate the phenomena of
EMI with following materials:
(a) Two different coils land 2 of copper wire having large no. of turns 50 and
100 respectively.
(b) A non-conducting cylinder
(c) A battery
(d) A plug key

Class X Science www.vedantu.com 29

(e) A galvanometer
(i) Draw a labeled diagram of your demonstration setup.
Ans:

(ii) How will you prove the phenomena of EMI.

Ans: When the key is closed, there is deflection in the galvanometer.

Long Answer Questions 5 Marks

1. Current- time graph from two different sources are shown in the figure.

(i) Name the type of current shown by graph (A) and (B)?
Ans: Graph A represents direct current and graph B represents alternating
current.

Class X Science www.vedantu.com 30

(ii) Name any one source of shown by (A) and (B)?
Ans: Source of (A) can be dry cell and Source of (B) can be AC generator.

(iii) What is frequency of current in case (B)?

Ans: As graph B represents the alternating current the frequency is given by,
1
f
T
1
f   50Hz
0.02

(iv) Write two differences between current shown by (A) and (B)?
Ans: The differences between AC and DC is listed below
Alternating current Direct current
AC is safe to transfer long distances DC is not used for long-distance as it
and it can maintain electric power. loses electric power.
The frequency is generally 50Hz or DC has no frequency.
60Hz.

2. Explain the principle, construction and working of an electric motor with

the help of a labeled diagram?
Ans: Principle – the electric motor is a rotating device that can convert electrical
energy into mechanical energy. An electric motor is based on the principle that
the current-carrying conductor experiences a force when placed in a magnetic
field. The direction of the force is given by Fleming’s left-hand rule if the
direction of the magnetic field and that of the current are mutually perpendicular.
Construction-

Class X Science www.vedantu.com 31

(i) Armature or coil- It consists of an insulated copper wire wound on a soft iron
core.
(ii) Strong field magnet- two pole pieces of a strong magnet that can provide a
strong magnetic field.
(iii)Split ring – split ring acts as a commutator which has two halves (R 1 and R2)
of a metallic ring that reverses the direction of the current in a coil.
(iv) Brushes- two carbon brushes touch the commutator (split ring).
(v) Battery – a battery is connected across the brushes.
Working - From the figure, ABCD is a rectangular coil of insulated copper wire
and this coil is placed between the south and north poles of a magnetic field in
such a way that the AB and CD are perpendicular to the direction of the magnetic
field. The ends of the coil are connected to the two halves of a split ring, say P
and Q. The external conducting edges of P and Q can touch two conducting
stationary brushes X and Y.
Let the current in the coil ABCD of motor enters from the source battery through
the conducting brush X, flow along ABCD, and finally flows back to the battery
through brush Y. On applying Fleming’s left-hand rule we find that force acting
on arm AB due to magnetic field pushes it downwards. But the force acting on
the arm CD pushes it upwards. Thus, the coil and the axle rotate anticlockwise.
Due to the action of split rings, P and Q change their contacts with brushes. Now,
P makes contact with Y and Q with X. As a result, the current begins to flow in
coil along DCBA. The arms are pushed in opposite directions and the coil
continues to rotate in the same direction.

Class X Science www.vedantu.com 32

3. Draw a labeled diagram of an electric motor. Explain its principle and
working. What is the function of split ring in an electric motor?
Ans: Electric motor labeled diagram of an electric motor is as follows:

Principle: the electric motor is a rotating device that can convert electrical energy
into mechanical energy. An electric motor is based on the principle that the
current-carrying conductor experiences a force when placed in a magnetic field.
The direction of the force is given by Fleming’s left-hand rule if the direction of
the magnetic field and that of the current are mutually perpendicular. Due to this
force, the conductor begins to move, if it is free to rotate.
Working- Let the current in the coil ABCD of motor enters from the source
battery through the conducting brush X, flow along ABCD, and finally flows
back to the battery through brush Y. On applying Fleming’s left-hand rule we
find that force acting on arm AB due to magnetic field pushes it downwards. But
the force acting on the arm CD pushes it upwards. Thus, the coil and the axle
rotate anticlockwise. Due to the action of split rings, P and Q change their contacts
with brushes. Now, P makes contact with Y and Q with X. As a result, the current
begins to flow in coil along DCBA. The arms are pushed in opposite directions
and the coil continues to rotate in the same direction.
Split ring- It acts as a commutator. The split ring reverses the direction of current
through the coil after every half rotation and thus the direction of force is also
reserved. As a result, the dc motor continues to rotate in the same direction.

4. Explain the underlying principle and working of an electric generator by

drawing a labeled diagram. What is the function of brushes?
Ans: Electric generator labeled diagram is given as follows:

Class X Science www.vedantu.com 33

Principle: An electric generator works on the principle of electromagnetic
induction.
Working: In an electric generator, a rotating rectangular coil ABCD is placed
between the south and north poles of a permanent magnet. As shown in the figure
the two ends of this coil are connected to the two rings R1 and R2. Let the, in the
beginning, brushes B1 and B2 are kept pressed separately on rings R1 and R2
respectively. The two rings are internally attached to an axle which may be
mechanically rotated from outside for the rotation of the coil inside the magnetic
field. To show the flow of current in the given external circuit, the outer ends of
the two brushes are connected to the galvanometer. The arm AB moves upwards
and the arm CD moves downwards when the axle attached to the two rings R1
and R2 is rotated then the magnetic field is produced by the permanent magnet.
By applying the induced currents are in these arms along the directions AB and
CD by Fleming’s right-hand rule. Thus, in the direction of ABCD an induced
current flows. The current in the external circuit flows from B2 to B1.
After half rotation, arm AB moves downward and arms CD upward to change the
direction opposite to the first case. Thus, after every half rotation current changes
its direction and an alternate current is obtained in the generator.
Brushes B1 and B2 are kept pressed on the two slip rings R1 and R2 separately.
The outer ends of the brushes are connected to the galvanometer. Thus, brushes
help to show the flow of current in the given external circuit...

Class X Science www.vedantu.com 34