Scribd
Upload
17 views4 pages

SMAW Reviewer

The document describes various hand tools used in metalworking and their purposes. It discusses tools for measuring and layout such as dividers and combination squares. It also mentions holding tools like vise grips and clamps, as well as tools for cutting, hammering, and manipulating materials like hacksaws, ball-peen hammers, and screwdrivers. Finally, it briefly covers maintenance of tools and safety practices.

Uploaded by

HUEMIL JETHRO DERIADA
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
17 views4 pages

SMAW Reviewer

The document describes various hand tools used in metalworking and their purposes. It discusses tools for measuring and layout such as dividers and combination squares. It also mentions holding tools like vise grips and clamps, as well as tools for cutting, hammering, and manipulating materials like hacksaws, ball-peen hammers, and screwdrivers. Finally, it briefly covers maintenance of tools and safety practices.

Uploaded by

HUEMIL JETHRO DERIADA
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

• Which hand tool is used to measure or set distances, and to layout

arcs and circles. Divider


• Which tool is used to tighten and loosen screws by pushing or pulling
screws in a rotating manner. Screwdriver
• Describe a pull-push-rule.
The tape rule blade is typically ½ inch wide and 72 inches long.
• Tool maker clamp is a holding tool which is also referred to as?
Parallel clamp
• A V block with clamp and employed to carry metal stocks for little
machining operation. Hand Vise
• Try-square and combination square are classified into __________.
Measuring tools
• A tool that has rows of teeth that form, shape, and finish metal
works? Hack saw
• Describe a welding rod. Welding rods consist of an internal metal
core and an outer coating called flux.
• The following sets are classified as Holding tools.
Drill vise, Machinist vise, Vise grip
• What driving tools would you use to deform the metal bars?
Ball-Peen Hammer
• The following sets are classified as measuring tools.
Combination square, Micrometer caliper, Steel rule
• What tool should you use to mark on the metal surface before cutting.
Punches
• What tool should you use to loosen the embedded nuts in the metal
surface? Wrench
• How are you going to manipulate the screwdriver?
Hold the screwdriver and turn clockwise to tighten the screw and
counterclockwise to loosen the screw.
• What tool should you use to hold the metal to be forged? Tong
• What tool should you use to measure a 25 feet long cables?
Pull push rule
• What tool is most appropriate if you were going to measure more
than 12 inches but less than 25 inches long? Steel tape
• What tool should you use if you are tasked to measure the squareness
of the project? Try square
• What tool should you use to measure the inside, outside diameter, as
well as the depth of hole and slot? Vernier Caliper
• It was developed in France and known as the S. I. (International
Standard). Metric System
• A system of measurement originated in England also known as the
U.S. customary system of measurement. English System
• The inch is divided into segments called _________. Graduation
• The inch can be divided into 16, 8, 4 and 2, parts. Equal
• Which of the following is not included in English System? Meter
• Mrs. Tony experiencing a back pain due to unbalance lifting of a box.
What type of hazard is this? Ergonomic hazard
• Why is wearing of PPE’s necessary?
Yes, to ensure the safety and the well being
• Which of the following sets belong to biological hazard?
virus, fungi, bacteria
• Excessive noise level is what type of hazard? Physical hazard
• By maintaining health and safety practices within the workplace, and
thus reducing absences and improving productivity, you'll be
______________ by retaining staff. Saving Money
• All defective hand tools with major defects are subjected to _______.
Repair
• Tools that are no longer functional may cause __________. Harm
• What simple maintenance is the application of lubricant substance to
the bolts, nuts, and other automotive parts. Lubricating
• Defective hand tools are kept and ____________.
marked as defective
• Why is following the 5S in cleaning your workplace is an infective
practice? Because it keeps the workplace clean and organized
• What is the Japanese term of the English word SANITIZE? Sieketsu
• What does symbol P represents? Pitch of Weld
• What does symbol F represents? Finish
• Symbol for Site Weld?
• Symbol for Site Weld around?
TRY SQUARE PLIERS

STEEL TAPE CHIPPING HAMMER

PUNCHES WRENCH

HACKSAW C – CLAMP

CHISEL TONG

You might also like