Smart Energy & Power Quality Solutions

Part no. 3303826

The device fronts can deviate!

Power Analyzer
02/2023

UMG 96-PQ-L
Doc. no. 2.061.071.3.c

(from firmware 3.42)

Data sheet
 DEVICE VIEWS

The figures are for illustration purposes only and are not to scale.
UMG 96-PQ-L

Front view Rear view

4,9 mm
0.19 in

Bottom view

0.24 in
6 mm
96 mm
3.78 in
3.78 in
96 mm

87,2 mm
3.43 in

96 mm Cut-out dimension:
3.78 in
92+0.8 mm x 92+0.8 mm
(3.62+0.03 in x 3.62+0.03 in)

Side view

87,2 mm 6 mm
3.43 in 0.24 in

2 – UMG 96-PQ-L data sheet • 02/2023

DEVICE VARIANTS

Network system and supply "Class S" variant

UMG 96-PQ-L
The UMG 96 PQ-L measurement devices are The UMG 96 PQ-L of class S additionally records
available in different variants: the power quality characteristics of class S ac-
· Both AC and DC voltage in two different voltage cording to IEC 61000-4-30.
ranges are suitable for the power supply of the
device1). The class-S-specific performance characteris-
tics are provided in the GridVis® software and in
· As a special feature of the UMG 96 PQ-L, Modbus addresses:
variants are also available for measurement in · Interharmonics
unearthed three-phase 3-conductor systems
(IT networks) up to 600 V AC. · Flicker

· Unbalances of voltage and current

· Rapid voltage change

· Frequency events

· Mains signal voltages (ripple control signal)

Subsequent class S activation for devices that

have already been installed is possible for a
fee through the GridVis® software (part number
5236020).

Variant Network system, supply Part number

TN / TT networks, 230 V option 1) 5236001

UMG 96-PQ-L
TN / TT networks, 24 V option 1) 5236002
(without class S)
TN / TT / IT networks, 230 V option 1) 5236005

TN / TT networks, 230 V option 1) 5236021

UMG 96-PQ-L
TN / TT networks, 24 V option 1) 5236022
Class S according to IEC 61000-4-30
TN / TT / IT networks, 230 V option 1) 5236025

Subsequent class S activation of a UMG 96-PQ-L 5236020

1) See „Supply voltage“ on page 4

INFORMATION
Detailed information on the device functions can be found in the usage information enclosed with the
device or is available for download at www.janitza.com.

02/2023 • UMG 96-PQ-L data sheet – 3

 TECHNICAL DATA
UMG 96-PQ-L

General
Net weight (with attached plug-in connectors) approx. 250 g (0.55 lbs)
Package weight (incl. accessories) approx. 500 g (1.1 lbs)
Battery Type Lithium CR2032, 3 V, (UL 1642 approved)
Data memory 64 MB
Backlight service life 40000 h
(backlight reduces to approx. 50% over this period)
Impact resistance IK07 according to IEC 62262

Transport and storage

The following information applies to devices that are transported or stored in their original packaging.
Free fall 1 m (39.37 in)
Temperature -25 °C (-13 °F) to +70 °C (158 °F)
Relative air humidity (non-condensing) 0 to 90% RH

Environmental conditions during operation

Install the device in a weather-protected and stationary location.
Protection class II according to IEC 60536 (VDE 0106, Part 1).
Rated temperature range -10 °C (14 °F) ... +55 °C (131 °F)
Relative air humidity (non-condensing) 0 to 75% RH
Operating elevation 0 .. 2000 m (6562 ft) above sea level
Pollution degree 2
Mounting orientation As desired
Ventilation No forced ventilation required.
Protection against foreign matter and water
- Front IP40 according to EN60529
- Rear IP20 according to EN60529
- Front with seal IP54 according to EN60529
Electromagnetic environmental conditions Class E2 (MID 2014/32/EU)
Mechanical environmental conditions Class M1 (MID 2014/32/EU)

Supply voltage
Option 230 V Nominal range AC 90 V - 277 V (50/60 Hz) or
DC 90 V - 250 V, 300 V CATIII
Power consumption max. 4.5 VA / 2 W
Option 24 V Nominal range AC 24 V - 90 V (50/60Hz) or
DC 24 V - 90 V, 150 V CATIII
Power consumption max. 4.5 VA / 2 W
Operating range +-10% of nominal range
Internal fuse, not replaceable Type T1A / 250 V DC / 277 V AC according to IEC 60127
Recommended overcurrent protective device for the Option 230 V: 6 - 16 A (Char. B)
line protection (UL approval) Option 24 V: 1 - 6 A (Char. B)

4 – UMG 96-PQ-L data sheet • 02/2023

 UMG 96-PQ-L
Voltage measurement
Three-phase 4-conductor systems with rated voltages up to 417 V / 720 V (+-10%) according to IEC
347 V / 600 V (+-10%) according to UL
Three-phase 3-conductor systems with rated voltages up to 600 V (+10%)
Single-phase 2-conductor system with rated voltages up to 480 V (+-10%)
Overvoltage category 600 V CAT III, 300 V CAT IV
Rated surge voltage 6 kV
Protection of the voltage measurement 1 - 10 A tripping characteristic B(with IEC/UL approval)
Measuring range L-N 01) .. 600 Vrms (max. overvoltage 800 Vrms)
Measuring range L-L 01) .. 1040 Vrms (max. overvoltage 1350 Vrms)
Resolution 0.01 V
Crest factor 2.45 (related to the measuring range)
Impedance 3 MΩ/phase
Power consumption approx. 0.1 VA
Sampling frequency 13.67 kHz
Sampling frequency (IT variant) 13.98 kHz
Frequency of the fundamental oscillation 45 Hz .. 65 Hz
- Resolution 0.01 Hz
Fourier analysis 1st - 65th harmonic

1) The device only determines measured values if a voltage L1-N of greater than 20 Veff (4-conductor measurement) or a
voltage L1-L2 of greater than 34 Veff (3-conductor measurement) is applied to voltage measurement input V1.

Current measurement
Nominal current 5 A
Measuring range 0.005 .. 6 Arms
Crest factor 2 (relative to 6 Arms)
Overvoltage category 300 V CAT II
Rated surge voltage 2 kV
Power consumption approx. 0.2 VA (Ri=5 mΩ)
Overload for 1 s 60 A (sinusoidal)
Resolution 0.1 mA (display 0.01 A)
Sampling frequency 13.67 kHz
Sampling frequency (IT variant) 13.98 kHz
Fourier analysis 1st - 65th harmonic

Serial interface
RS-485 - Modbus RTU/client device 9.6 kbps, 19.2 kbps, 38.4 kbps, 57.6 kbps, 115.2 kbps

Digital outputs
3 digital outputs, solid state relays, not short-circuit proof.
Switching voltage max. 33 V AC, 40 V DC
Switching current max. 50 mAeff AC/DC
Response time approx. 200 ms
Pulse output max. 50 Hz (energy pulses)

Digital inputs
3 digital inputs, solid state relays, not short-circuit proof.
Maximum counter frequency 20 Hz
Input signal applied 18 V .. 28 V DC (typically 4 mA)
Input signal not applied 0 .. 5 V DC, current less than 0.5 mA

Cable length (digital inputs/outputs)

Up to 30 m (32.81 yd) Unshielded
Greater than 30 m (32.81 yd) Shielded

02/2023 • UMG 96-PQ-L data sheet – 5

UMG 96-PQ-L

Analog outputs
External power supply max. 33 V
Current 0 .. 20 mA
Update time 1s
Load max. 300 Ω
Resolution 10 bit

Connecting capacity of the terminals (supply voltage)

Connectible conductors. Only connect one conductor per terminal point!
Single core, multi-core, fine-stranded 0.2 - 4.0 mm2, AWG 28-12
Wire ferrules (non-insulated) 0.2 - 2.5 mm2, AWG 26-14
Wire ferrules (insulated) 0.2 - 2.5 mm2, AWG 26-14
Tightening torque 0.4 - 0.5 Nm (3.54 - 4.43 lbf in)
Strip length 7 mm (0.2756 in)

Connecting capacity of the terminals (voltage measurement)

Connectible conductors. Only connect one conductor per terminal point!
Single core, multi-core, fine-stranded 0.2 - 4.0 mm2, AWG 28-12
Wire ferrules (non-insulated) 0.2 - 2.5 mm2, AWG 26-14
Wire ferrules (insulated) 0.2 - 2.5 mm2, AWG 26-14
Tightening torque 0.4 - 0.5 Nm (3.54 - 4.43 lbf in)
Strip length 7 mm (0.2756 in)

Connecting capacity of the terminals (current measurement)

Connectible conductors. Only connect one conductor per terminal point!
Single core, multi-core, fine-stranded 0.2 - 4 mm2, AWG 28-12
Wire ferrules (non-insulated) 0.2 - 2.5 mm2, AWG 26-14
Wire ferrules (insulated) 0.2 - 2.5 mm2, AWG 26-14
Tightening torque 0.4 - 0.5 Nm (3.54 - 4.43 lbf in)
Strip length 7 mm (0.2756 in)

Terminal connection capacity (serial interface)

Connectible conductors. Only connect one conductor per terminal point!
Single core, multi-core, fine-stranded 0.2 - 1.5 mm2, AWG 28-16
Wire ferrules (non-insulated) 0.2 - 1.5 mm2, AWG 26-16
Wire ferrules (insulated) 0.2 - 1.5 mm2, AWG 26-16
Tightening torque 0.2 - 0.25 Nm (1.77 - 2.21 lbf in)
Strip length 7 mm (0.2756 in)

Connecting capacity of the terminals (digital inputs/outputs, analog output)

Connectible conductors. Only connect one conductor per terminal point!
Single core, multi-core, fine-stranded 0.2 - 1.5 mm2, AWG 28-16
Wire ferrules (non-insulated) 0.2 - 1.5 mm2, AWG 26-16
Wire ferrules (insulated) 0.2 - 1.5 mm2, AWG 26-16
Tightening torque 0.2 - 0.25 Nm (1.77 - 2.21 lbf in)
Strip length 7 mm (0.2756 in)

6 – UMG 96-PQ-L data sheet • 02/2023

PERFORMANCE CHARACTERISTICS OF FUNCTIONS

UMG 96-PQ-L
Function Symbol Accuracy class Measuring range Display range

Total active power P 0.5 (IEC61557-12)

1)
0 W .. 12.6 kW 0 W .. 999 GW *

Total reactive power QA, Qv 1 (IEC61557-12) 0 var .. 16.6 kvar 0 var .. 999 Gvar *

Total apparent power SA, Sv 0.51) (IEC61557-12) 0 VA .. 12.6 kVA 0 VA .. 999 GVA *

Total active energy Ea 0.21) (IEC61557-12) 0 Wh .. 999 GWh 0 Wh .. 999 GWh *

0.2S1) (IEC62053-22)
0.2 (ANSI C12.20)

Total reactive energy ErA, ErV 1 (IEC61557-12) 0 varh .. 999 Gvarh 0 varh .. 999 Gvarh *

Total apparent energy EapA, EapV 0.5 (IEC61557-12)

1)
0 VAh .. 999 GVAh 0 VAh .. 999 GVAh *

Frequency f 0.05 (IEC61557-12) 42.5 Hz .. 69 Hz 42.50 Hz .. 69.00 Hz

Phase current I 0.2 (IEC61557-12) 0 Arms .. 7 Arms 0 A .. 999 kA

Neutral conductor current calcu- INc 1.0 (IEC61557-12) 0.03 A .. 25 A 0.03 A .. 999 kA
lated

Voltage U L-N 0.2 (IEC61557-12) 10 Vrms .. 600 Vrms 0 V .. 999 kV

Voltage U L-L 0.2 (IEC61557-12) 18 Vrms .. 1040 Vrms 0 V .. 999 kV

Power factor PFA, PFV 0.5 (IEC61557-12) 0.00 .. 1.00 0.00 .. 1.00

Transient overvoltages Utr - - -

Voltage harmonics Uh Cl. 1 (IEC61000-4-7) 1 .. 65 0 V .. 999 kV

THD of voltage 2) THDu 1.0 (IEC61557-12) 0% .. 999% 0% .. 999%

THD of voltage 3)
THD-Ru - - -

Current harmonics Ih Cl. 1 (IEC61000-4-7) 1 .. 65 0 A .. 999 kA

THD of current 2) THDi 1.0 (IEC61557-12) 0% .. 999% 0% .. 999%

THD of current 3) THD-Ri - - -

Accuracy of events - - -

Short-term flicker, long-term Pst, Plt Class 1 (IEC61000-4-15) 0.4 Pst ... 10.0 Pst 0 .. 10
flicker

1) Accuracy class 0.2/0.2S with ../5A transformer. * When the maximum total energy values are
Accuracy class 0.5/0.5S with ../1A transformer. reached, the display returns to 0 W.
2) Referenced to the fundamental oscillation.
3) Referenced to the effective value.

02/2023 • UMG 96-PQ-L data sheet – 7

Smart Energy & Power Quality Solutions

Janitza electronics GmbH

Vor dem Polstück 6 | 35633 Lahnau
Germany

Tel.: +49 6441 9642-0

[email protected] | www.janitza.com