FS-535 Finisher

INSTALLATION MANUAL
Applied Machines: C754/C654
COLOR MFP: 75 ppm/65 ppm
Product Code: A2X0/A2X1

Caution: No. Name Shape Q’ty

Lifting the machine in an awkward position or
transporting it in a poorly balanced position could 8. Mounting
result in personal injury. When transporting the bracket G
machine, assign an adequate number of persons 1
to the job and ensure that each person can take a
good position of not being excessively loaded. A2Y1IXC007DA

(mass: approx. 59 kg (130-11/16 lb)) 9. Mounting

bracket H *1
I. Accessory parts 1

No. Name Shape Q’ty

A3EPIXC009DA
1. Horizontal
10. Mounting
transport unit
bracket I
1 1

A2Y1IXC008DA
A2Y1IXC001DB
11. Exit tray
2. Mounting (upper)
bracket A 1
1
A11PIXC001DB
A2Y1IXC002DA
12. Exit tray
3. Mounting (lower)
bracket B
1 1

A2Y1IXC003DB A07UIXC065DA

4. Mounting 13. Stapler cover

bracket C *1 1
1
A2Y1IXC004DB

5. Mounting A11PIXC035DA

bracket D *1 14. Film

1
2
A2Y1IXC005DB

6. Mounting A2Y1IXC009DA
bracket E
15. Guide plate A
1
1
A11PIXC019DB

7. Mounting A3EPIXC010DA

bracket F *1 16. Guide plate B

1
1
A2Y1IXC006DB

A3EPIXC011DA

A2Y1-9550-00
E-1
No. Name Shape Q’ty II. Confirmation before installation
1. When transporting the finisher, be sure to move it
17. Mounting screw
in the direction illustrated below so as not to
1
deform the casters on the paper exit tray side.
A07UIXC066DA

18. Screw A
(4 × 8 mm) 8
4038IXC033DA
OK
19. Screw B *2
(4 × 16 mm) 4

A2Y1IXC043DA
NG
20. Screw C *1
(3 × 16 mm) 5
A2Y1IXC044DA

21. Screw D A11PIXC003DB

(3 × 6 mm) 5
9735
2. Choose a horizontal and stable floor for installing
22. Screw E the machine.
(4 × 8 mm) 2 3. The packaging material should not be reused for
repacking.
A092IXC012DA
4. When installing the optional punch kit and saddle
23. Installation stitcher, attach them to the finisher first, and then
manual attach the finisher to the machine.
1
set

4980IXC019DA
III. Installation procedures
1. Turn off the machine and unplug the power cord
*1
This part is not used in this installation. from the power outlet.
*2
Two screws are used in this installation. 2. Remove the user’s guide holder from the
machine.

After unpacking, be sure to get rid of the

packaging materials and keep them out of
the reach of children.
Putting the head in the plastic bag
involves danger of suffocation.

Note:
This manual provides the illustrations of the acces-
sory parts and machine that may be slightly differ-
A2Y1IXC010DA
ent in shape from yours. In that case, instead of
the illustrations, use the appearance of your
machine to follow the installation procedure. This 3. Remove the output tray if it is mounted on the
does not cause any significant change or problem machine.
with the procedure. Note:
For the removal procedure, see the installation
manual for the output tray (OT-503).

E-2
4. Remove the protective sheet of the horizontal 7. Remove the cover shown in the illustration.
transport unit. (Three screws)

A2Y1IXC045DA A2Y1IXC013DA

5. Remove protective tape of the horizontal trans- 8. Remove the cover shown in the illustration from
port unit. the front of the horizontal transport unit. (Two
screws)

A2Y1IXC046DA

A2Y1IXC014DA

6. Remove the cover shown in the illustration from

the back of the horizontal transport unit. (Two 9. Attach the guide plate A to the horizontal trans-
screws) port unit by fitting the two tabs into the slots.

A2Y1IXC012DA A2Y1IXC015DA

E-3
10. Attach the guide plate B. (Two screws removed 13. Mount the horizontal transport unit to the
in step 8) machine. (Two supplied screws A)

A2Y1IXC016DA A2Y1IXC019DB

11. Attach the supplied mounting bracket A (front) to 14. Attach the supplied mounting bracket E to the
the left side of the machine. (Two supplied left side of the machine. (Two supplied screws
screws A) A)
Note:
Temporarily fix the cable of the horizontal transport
unit onto the upper portion of the machine to pre-
vent it from being caught by the mounting bracket
E.

A2Y1IXC017DA

12. Attach the supplied mounting bracket B (rear) to

the left side of the machine. (Two supplied
screws A)
OK NG

A2Y1IXC020DB

A2Y1IXC018DB

E-4
15. Attach the supplied mounting bracket G to the 17. Remove the protective tape and the protective
left side of the machine. (Two supplied screws materials from the finisher.
B)

A2Y1IXC047DA

A2Y1IXC021DA

16. Remove one knockout (front) from the lower left

side of the machine with nippers.

A11PIXC007DD

A2Y1IXC022DA

A2Y1IXC048DA

E-5
18. Attach the supplied mounting bracket I to the 20. Attach the supplied stapler cover. (Four supplied
right side of the finisher at the position shown in screws D)
the illustration. (One supplied screw D)

A2Y1IXC031DA

A2Y1IXC042DB

21. Connect the three connectors of the finisher to

19. Remove paper backing from the two supplied the horizontal transport unit.
films and attach them to the finisher at the posi-
tion shown in the illustration.
Note:
Use the below as a guide to attach the films.
• Vertical direction:
1st film (upper): Align the film with the mark on
the finisher.
2nd film (lower): Attach the 2nd film right below
the 1st film, leaving no space
between the films.
• Front and back direction:
Align the sides of the 1st and 2nd films with the
end of the finisher’s plate.

Mark

A2Y1IXC033DA

22. Install the finisher on the machine.

Note:
Align the hook portion of the mounting bracket E
with the hole on the right side of the finisher. Then,
push the finisher toward the rear.

A2Y1IXC030DB A2Y1IXC034DA

E-6
23. Open the front door of the finisher and secure 25. Install the supplied exit tray (lower) to the up/
the finisher to the machine. (One supplied down section of the finisher. (Two supplied
mounting screw) screws E)
Note:
When installing the exit tray (lower), hook the
guide holes of the exit tray (lower) over the four
mounting clamps and then fix it.

A2Y1IXC035DB

24. Insert the supplied exit tray (upper) into the sub
tray paper exit slot on the finisher.
Note:
When installing the exit tray (upper), insert the left
and right side projections on the finisher into the
holes located on both ends of the exit tray (upper),
respectively.
A11PIXC014DA

26. Remove the cover shown in the illustration from

the back of the machine. (One screw)

A2Y1IXC036DA

27. Plug in the two connectors of the horizontal

transport unit. Fit the head of the cable tie into
the mounting hole on the machine.
A11PIXC013DB

Connector

Cable tie

A2Y1IXC037DA

E-7
28. Reattach the cover removed in step 26. (One
screw)
Note:
Be careful not to pinch the harness.

29. Reinstall the user’s guide holder, which has

been removed in step 2, to the upper or lower
position shown.
Mounting the holder to the upper position

A2Y1IXC039DA

Mounting the holder to the lower position

A2Y1IXC040DA

30. Push the rear left part of the finisher toward the
machine to place the finisher parallel to the
machine. Bring the plate springs of the mounting
bracket E into contact with the plate of the fin-
isher.
Note:
Ensure the above mentioned process to be done
appropriately in order to secure the finisher’s
grounding.

<OK>

Contacted
<NG>

Not contacted
A2Y1IXC041DA

E-8