Scribd
Upload
251 views

Cable Connector Db9 Guide

This technical support guide provides instructions for creating an interconnect cable to allow the use of PC-based configurator programs for tuning and setting up EAS systems. It lists the necessary tools and parts, which are readily available from stores like RadioShack, and provides step-by-step instructions for assembling the cable that include stripping and crimping wires according to color codes. Global contact information is also included for technical support.

Uploaded by

Raul Ernesto Gallegos Morales
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
251 views

Cable Connector Db9 Guide

This technical support guide provides instructions for creating an interconnect cable to allow the use of PC-based configurator programs for tuning and setting up EAS systems. It lists the necessary tools and parts, which are readily available from stores like RadioShack, and provides step-by-step instructions for assembling the cable that include stripping and crimping wires according to color codes. Global contact information is also included for technical support.

Uploaded by

Raul Ernesto Gallegos Morales
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

EAS/RFID TECHNICAL SUPPORT GUIDE

To: Distribution
From: Technical Support
Date: February 5, 2009
Re: Computer Interconnect Cable for EAS Products

Most Sensormatic EAS systems require an Interconnect cable to allow the use of PC based
Configurator programs for tuning and setup. This guide presents the most direct method for
creating these cables with some handy references for sources of parts. These are not intended as
recommendations or endorsements of specific vendors, and should not be construed as such.

Many of these parts are available from Radio Shack (part numbers attached), DIY, and some
retailers such as Wal-Mart.

Tools Parts
Side cut pliers Dsub hood 276-1513
Modular Crimping tool Dsub9 connx crimp 276-1428
Pin Insertion tools, D- Cord25ft 279-295
sub Cord12ft 279-306

Instructions
1. Acquire a handset cable of suitable length (25 ft extended is the best).

2. Orient cable connectors as shown in figure 1 and note color orientation of internal wires.
Note: Some headset cords do not have color coded wires in them, this makes it difficult to follow the
color coded orientation for cable assembly. To solve this problem, hold cable in the orientation shown
in figure 1 then mark the same side of both ends of the cable below the connectors before cutting.

3. Using a wire cutter, cut one connector off the cable. Be sure that the cut is straight across the cable
(not diagonally).

4. Insert the cut end of the cable into the stripper portion of the crimping tool, squeeze and remove
outer jacket from cable. Be careful not to remove or break the inner conductors colored insulation.

Company Confidential do not reproduce or distribute


© 2008 Sensormatic Electronics Corportation
5. Strip back the ends of the individual conductors and crimp on the pins. Then using Figure 2,
connect to the DB9 connector.

6. Complete the connector the assembling the hood.

Company Confidential do not reproduce or distribute


© 2008 Sensormatic Electronics Corportation
For further clarification this graphic has been added

Company Confidential do not reproduce or distribute


© 2008 Sensormatic Electronics Corportation
GLOBAL CONTACT INFORMATION
Corporate Sensormatic Technical Support EMEA Sensormatic Technical Support
Toll Free: 800-543-9740 Toll Free: +800 CALLTYCO or (+800-2255 8926)
Direct Dial: 561-912-6796 Direct Dial: +31 (0475 352 722)
Email: [email protected] UK only: +44 (08701 238 787)
Hours 8:00am -6:00 pm EST France only: +33 (04 72 79 14 83)
Spain only +900 10 19 45
Hours 8:00 am – 18:00 pm CET
EMEA Technical Support Website:
ASIA Sensormatic Technical Support http://www.calltyco.com
Tyco Safety Product (Singapore) Email EMEA Support Inquires:
Marcus Seen-Technical [email protected]
DID +65 6319 9838 Email EMEA Training Inquires:
Fax +65 6319 9821 [email protected]
Email [email protected]

Company Confidential do not reproduce or distribute


© 2008 Sensormatic Electronics Corportation

You might also like