Scribd
Upload
6K views

2.9 Engine Torque Specs

This document provides torque specifications for various components on a 1989 Ford Bronco II 2.9L engine. It lists the application and the recommended foot-pounds or inch-pounds of torque for components like camshaft sprocket bolts, cylinder head bolts, exhaust manifold bolts, flywheel bolts, intake manifold bolts, oil pan bolts, spark plugs, water pump bolts and more. Tightening sequences and additional steps are specified for some components.

Uploaded by

Cody Rea
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
6K views

2.9 Engine Torque Specs

This document provides torque specifications for various components on a 1989 Ford Bronco II 2.9L engine. It lists the application and the recommended foot-pounds or inch-pounds of torque for components like camshaft sprocket bolts, cylinder head bolts, exhaust manifold bolts, flywheel bolts, intake manifold bolts, oil pan bolts, spark plugs, water pump bolts and more. Tightening sequences and additional steps are specified for some components.

Uploaded by

Cody Rea
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Printer Friendly View https://www2.prodemand.com/Print/Index?content=article&module=fal...

YMMS: 1989 Ford Bronco II Oct 28, 2020


Engine: 2.9L Eng License:
VIN: Odometer:

TORQUE SPECIFICATIONS

TORQUE SPECIFICATIONS

Application Ft. Lbs. (N.m)

Camshaft Sprocket Bolt 19-28 (26-38)

Camshaft Thrust Plate Bolt 13-16 (18-22)

Connecting Rod Nut 19-24 (26-33)

Crankshaft Damper Bolt 85-96 (116-131)

Cylinder Head Bolt (1)

1st Step 22 (30)

2nd Step 51-55 (69-75)

3rd Step Pause 5 minutes

4th Step Additional 90 degrees

Exhaust Manifold Bolt 20-30 (27-41)

Fan Clutch-to-Water Pump Nut (2) 15-25 (20-34)

Flywheel-to-Crankshaft Bolt 47-52 (64-71)

Front Cover Bolt 13-16 (18-22)

Main Bearing Cap Bolt 65-75 (88-102)

Rocker Arm Shaft Bolt 43-50 (58-68)

Water Pump Pulley Bolt 15-22 (20-30)

INCH Lbs. (N.m)

Lower Intake Manifold Bolt (3)

1st Step Hand Start & Snug

2nd Step 36-72 (4-8)

3rd Step 72-132 (8-15)

4th Step 132-180 (15-21)

5th Step (4) 180-216 (21-25)

Oil Pan Bolt 44-71 (5-8)

Oil Pump Case Bolt 80-115 (9-13)

Spark Plug 60-132 (7-15)

Throttle Body-to-Intake Bolt 80-115 (9-13)

Timing Chain

1 of 2 10/28/2020, 10:12
Printer Friendly View https://www2.prodemand.com/Print/Index?content=article&module=fal...

Guide Bolt 80-115 (9-13)

Tensioner Bolt 80-115 (9-13)

Upper Intake Manifold Bolt

1st Step 84 (10)

2nd Step 180-216 (21-25)

Valve Cover Bolt 36-60 (4-7)

Water Pump Bolt 84-108 (10-12)

(1) Tighten in sequence. See Figure.


(2) Left-hand thread.
(3)
Sequence not available from manufacturer.
(4)
Repeat after warm up.

2 of 2 10/28/2020, 10:12

You might also like