®

Intergraph Smart 3D
2D Symbols Reference Data Guide
Version 2018 (12.0)
June 2018
Copyright
Copyright © 2006-2018 Hexagon AB and/or its subsidiaries and affiliates. All rights reserved.
This computer program, including software, icons, graphic symbols, documentation, file formats, and audio-visual displays; may be
used only as pursuant to applicable software license agreement; contains confidential and proprietary information of Hexagon AB
and/or third parties which is protected by patent, trademark, copyright law, trade secret law, and international treaty, and may not be
provided or otherwise made available without proper authorization from Hexagon AB and/or its subsidiaries and affiliates.
Portions of this software are owned by Spatial Corp. © 1986-2018. All Rights Reserved.
Portions of the user interface are copyright © 2012-2018 Telerik AD.

U.S. Government Restricted Rights Legend

Use, duplication, or disclosure by the government is subject to restrictions as set forth below. For civilian agencies: This was
developed at private expense and is "restricted computer software" submitted with restricted rights in accordance with
subparagraphs (a) through (d) of the Commercial Computer Software - Restricted Rights clause at 52.227-19 of the Federal
Acquisition Regulations ("FAR") and its successors, and is unpublished and all rights are reserved under the copyright laws of the
United States. For units of the Department of Defense ("DoD"): This is "commercial computer software" as defined at DFARS
252.227-7014 and the rights of the Government are as specified at DFARS 227.7202-3.
Unpublished - rights reserved under the copyright laws of the United States.
Hexagon PPM
305 Intergraph Way
Madison, AL 35758

Documentation
Documentation shall mean, whether in electronic or printed form, User's Guides, Installation Guides, Reference Guides,
Administrator's Guides, Customization Guides, Programmer's Guides, Configuration Guides and Help Guides delivered with a
particular software product.

Other Documentation
Other Documentation shall mean, whether in electronic or printed form and delivered with software or on Intergraph Smart Support,
SharePoint, or box.net, any documentation related to work processes, workflows, and best practices that is provided by Intergraph
as guidance for using a software product.

Terms of Use
a. Use of a software product and Documentation is subject to the Software License Agreement ("SLA") delivered with the software
product unless the Licensee has a valid signed license for this software product with Intergraph Corporation. If the Licensee has
a valid signed license for this software product with Intergraph Corporation, the valid signed license shall take precedence and
govern the use of this software product and Documentation. Subject to the terms contained within the applicable license
agreement, Intergraph Corporation gives Licensee permission to print a reasonable number of copies of the Documentation as
defined in the applicable license agreement and delivered with the software product for Licensee's internal, non-commercial
use. The Documentation may not be printed for resale or redistribution.
b. For use of Documentation or Other Documentation where end user does not receive a SLA or does not have a valid license
agreement with Intergraph, Intergraph grants the Licensee a non-exclusive license to use the Documentation or Other
Documentation for Licensee’s internal non-commercial use. Intergraph Corporation gives Licensee permission to print a
reasonable number of copies of Other Documentation for Licensee’s internal, non-commercial use. The Other Documentation
may not be printed for resale or redistribution. This license contained in this subsection b) may be terminated at any time and
for any reason by Intergraph Corporation by giving written notice to Licensee.

Disclaimer of Warranties
Except for any express warranties as may be stated in the SLA or separate license or separate terms and conditions, Intergraph
Corporation disclaims any and all express or implied warranties including, but not limited to the implied warranties of merchantability
and fitness for a particular purpose and nothing stated in, or implied by, this document or its contents shall be considered or deemed
a modification or amendment of such disclaimer. Intergraph believes the information in this publication is accurate as of its
publication date.
The information and the software discussed in this document are subject to change without notice and are subject to applicable
technical product descriptions. Intergraph Corporation is not responsible for any error that may appear in this document.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 2

The software, Documentation and Other Documentation discussed in this document are furnished under a license and may be used
or copied only in accordance with the terms of this license. THE USER OF THE SOFTWARE IS EXPECTED TO MAKE THE FINAL
EVALUATION AS TO THE USEFULNESS OF THE SOFTWARE IN HIS OWN ENVIRONMENT.
Intergraph is not responsible for the accuracy of delivered data including, but not limited to, catalog, reference and symbol data.
Users should verify for themselves that the data is accurate and suitable for their project work.

Limitation of Damages
IN NO EVENT WILL INTERGRAPH CORPORATION BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL INCIDENTAL,
SPECIAL, OR PUNITIVE DAMAGES, INCLUDING BUT NOT LIMITED TO, LOSS OF USE OR PRODUCTION, LOSS OF
REVENUE OR PROFIT, LOSS OF DATA, OR CLAIMS OF THIRD PARTIES, EVEN IF INTERGRAPH CORPORATION HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
UNDER NO CIRCUMSTANCES SHALL INTERGRAPH CORPORATION’S LIABILITY EXCEED THE AMOUNT THAT
INTERGRAPH CORPORATION HAS BEEN PAID BY LICENSEE UNDER THIS AGREEMENT AT THE TIME THE CLAIM IS
MADE. EXCEPT WHERE PROHIBITED BY APPLICABLE LAW, NO CLAIM, REGARDLESS OF FORM, ARISING OUT OF OR IN
CONNECTION WITH THE SUBJECT MATTER OF THIS DOCUMENT MAY BE BROUGHT BY LICENSEE MORE THAN TWO (2)
YEARS AFTER THE EVENT GIVING RISE TO THE CAUSE OF ACTION HAS OCCURRED.
IF UNDER THE LAW RULED APPLICABLE ANY PART OF THIS SECTION IS INVALID, THEN INTERGRAPH LIMITS ITS
LIABILITY TO THE MAXIMUM EXTENT ALLOWED BY SAID LAW.

Export Controls
Intergraph Corporation’s commercial-off-the-shelf software products, customized software and/or third-party software, including any
technical data related thereto (“Technical Data”), obtained from Intergraph Corporation, its subsidiaries or distributors, is subject to
the export control laws and regulations of the United States of America. Diversion contrary to U.S. law is prohibited. To the extent
prohibited by United States or other applicable laws, Intergraph Corporation software products, customized software, Technical Data,
and/or third-party software, or any derivatives thereof, obtained from Intergraph Corporation, its subsidiaries or distributors must not
be exported or re-exported, directly or indirectly (including via remote access) under the following circumstances:
a. To Cuba, Iran, North Korea, the Crimean region of Ukraine, or Syria, or any national of these countries or territories.
b. To any person or entity listed on any United States government denial list, including, but not limited to, the United States
Department of Commerce Denied Persons, Entities, and Unverified Lists, the United States Department of Treasury Specially
Designated Nationals List, and the United States Department of State Debarred List
(https://build.export.gov/main/ecr/eg_main_023148).
c. To any entity when Customer knows, or has reason to know, the end use of the software product, customized software,
Technical Data and/or third-party software obtained from Intergraph Corporation, its subsidiaries or distributors is related to the
design, development, production, or use of missiles, chemical, biological, or nuclear weapons, or other un-safeguarded or
sensitive nuclear uses.
d. To any entity when Customer knows, or has reason to know, that an illegal reshipment will take place.
Any questions regarding export/re-export of relevant Intergraph Corporation software product, customized software, Technical Data
and/or third-party software obtained from Intergraph Corporation, its subsidiaries or distributors, should be addressed to PPM’s
Export Compliance Department, 305 Intergraph Way, Madison, Alabama 35758 USA or at [email protected].
Customer shall hold harmless and indemnify PPM and Hexagon Group Company for any causes of action, claims, costs, expenses
and/or damages resulting to PPM or Hexagon Group Company from a breach by Customer.

Trademarks
Intergraph®, the Intergraph logo®, Intergraph Smart®, SmartPlant®, SmartMarine®, SmartSketch®, SmartPlant Cloud®, PDS®,
FrameWorks®, I-Route, I-Export, Isogen®, SPOOLGEN, SupportManager®, SupportModeler®, SAPPHIRE®, TANK, PV Elite®,
CADWorx®, CADWorx DraftPro®, GTSTRUDL®, and CAESAR II® are trademarks or registered trademarks of Intergraph Corporation
or its affiliates, parents, subsidiaries. Hexagon and the Hexagon logo are registered trademarks of Hexagon AB or its subsidiaries.
Microsoft and Windows are registered trademarks of Microsoft Corporation. ACIS is a registered trademark of SPATIAL
TECHNOLOGY, INC. Infragistics, Presentation Layer Framework, ActiveTreeView Ctrl, ProtoViewCtl, ActiveThreed Ctrl,
ActiveListBar Ctrl, ActiveSplitter, ActiveToolbars Ctrl, ActiveToolbars Plus Ctrl, and ProtoView are trademarks of Infragistics, Inc.
Incorporates portions of 2D DCM, 3D DCM, and HLM by Siemens Product Lifecycle Management Software III (GB) Ltd. All rights
reserved. Gigasoft is a registered trademark, and ProEssentials a trademark of Gigasoft, Inc. VideoSoft and VXFlexGrid are either
registered trademarks or trademarks of ComponentOne LLC 1991-2018, All rights reserved. Oracle, JD Edwards, PeopleSoft, and
Retek are registered trademarks of Oracle Corporation and/or its affiliates. Tribon is a trademark of AVEVA Group plc. Alma and
act/cut are trademarks of the Alma company. Other brands and product names are trademarks of their respective owners.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 3

Contents
Preface .......................................................................................................................................................... 8
What's New in 2D Symbols Reference Data .......................................................................................... 8

2D Symbols Reference Data ....................................................................................................................... 9

Bracket Symbols ....................................................................................................................................... 10

2S Brackets ........................................................................................................................................... 10
2S Integrated Brackets ......................................................................................................................... 13
3S Brackets ........................................................................................................................................... 14
3S Flanged Brackets ............................................................................................................................. 18
4S Brackets ........................................................................................................................................... 20
5S Brackets ........................................................................................................................................... 21

Flange Contours for Brackets .................................................................................................................. 23

Standard Bracket Flange Contour ........................................................................................................ 23

Chamfers .................................................................................................................................................... 24
Double Sided Style1 Chamfer............................................................................................................... 24
Single Sided Style 1 Chamfers ............................................................................................................. 25

Collars and Clips ....................................................................................................................................... 26

Non-Tight Clips ..................................................................................................................................... 26
Tight Collars .......................................................................................................................................... 30

Corner Features for Plates and Stiffeners .............................................................................................. 39

Corner Features for Members .................................................................................................................. 49

Member Cross Sections............................................................................................................................ 54

Cross Section Symbol 2L ...................................................................................................................... 56
Cross Section Symbol BUBoxFM ......................................................................................................... 59
Cross Section Symbol BUC .................................................................................................................. 62
Cross Section Symbol BUCan .............................................................................................................. 65
Cross Section Symbol BUCone ............................................................................................................ 68
Cross Section Symbol BUEndCan........................................................................................................ 70
Cross Section Symbol BUFlat............................................................................................................... 72
Cross Section Symbol BUI .................................................................................................................... 75
Cross Section Symbol BUIHaunch ....................................................................................................... 77
Cross Section Symbol BUITaperWeb ................................................................................................... 80
Cross Section Symbol BUIUE............................................................................................................... 83
Cross Section Symbol BUL ................................................................................................................... 86
Cross Section Symbol BUT .................................................................................................................. 89

Intergraph Smart® 3D 2D Symbols Reference Data Guide 4

 Contents

Cross Section Symbol BUTube ............................................................................................................ 91

Cross Section Symbol C (MC) .............................................................................................................. 93
Cross Section Symbol CS ..................................................................................................................... 96
Cross Section Symbol HSSC (Pipe) ..................................................................................................... 98
Cross Section Symbol HSSCs ............................................................................................................ 100
Cross Section Symbol HSSR.............................................................................................................. 103
Cross Section Symbol HSSRs ............................................................................................................ 105
Cross Section Symbol HW .................................................................................................................. 108
Cross Section Symbol HWWF ............................................................................................................ 110
Cross Section Symbol L ...................................................................................................................... 112
Cross Section Symbol Rect ................................................................................................................ 116
Cross Section Symbol RectC.............................................................................................................. 118
Cross Section Symbol RectCWF ........................................................................................................ 120
Cross Section Symbol RectWF........................................................................................................... 123
Cross Section Symbol RS ................................................................................................................... 125
Cross Section Symbol S ..................................................................................................................... 127
Cross Section Symbol ST ................................................................................................................... 130
Cross Section Symbol T (MT) ............................................................................................................. 133
Cross Section Symbol W (M) .............................................................................................................. 135
Cross Section Symbol Wedge ............................................................................................................ 138
Cross Section Symbol WedgeWF....................................................................................................... 141

Wall Cross Sections ................................................................................................................................ 144

Cross Section Symbol HW .................................................................................................................. 145
Cross Section Symbol HWWF ............................................................................................................ 147
Cross Section Symbol Rect ................................................................................................................ 149
Cross Section Symbol RectC.............................................................................................................. 151
Cross Section Symbol RectCWF ........................................................................................................ 154
Cross Section Symbol RectWF........................................................................................................... 156
Cross Section Symbol Wedge ............................................................................................................ 159
Cross Section Symbol WedgeWF....................................................................................................... 161

Profile Cross Sections ............................................................................................................................ 164

Cross Section Symbol B ..................................................................................................................... 165
Cross Section Symbol BUL2............................................................................................................... 166
Cross Section Symbol BUL3............................................................................................................... 168
Cross Section Symbol BUT ................................................................................................................ 171
Cross Section Symbol C_SS .............................................................................................................. 172
Cross Section Symbol C_SType......................................................................................................... 174
Cross Section Symbol EA ................................................................................................................... 176
Cross Section Symbol FB ................................................................................................................... 178
Cross Section Symbol HalfR............................................................................................................... 181
Cross Section Symbol I ....................................................................................................................... 183
Cross Section Symbol I_SType .......................................................................................................... 185
Cross Section Symbol P ..................................................................................................................... 187
Cross Section Symbol R ..................................................................................................................... 189
Cross Section Symbol SB ................................................................................................................... 191
Cross Section Symbol SqTu ............................................................................................................... 193
Cross Section Symbol T ..................................................................................................................... 194

Intergraph Smart® 3D 2D Symbols Reference Data Guide 5

 Contents

Cross Section Symbol T_SType ......................................................................................................... 194

Cross Section Symbol UA ................................................................................................................... 197

Edge Features .......................................................................................................................................... 200

Profile End Cuts ....................................................................................................................................... 201

Weld and Clip End Cuts ...................................................................................................................... 201
Bounded with Plate or Profile Web............................................................................................... 201
Bounded Section Type: BUT, BUTL2........................................................................................... 215
Bounded Section Type: FB .......................................................................................................... 225
Bounded with Profile Top (Tripping Case) ................................................................................... 229
Free End ....................................................................................................................................... 229
Edge Reinforcement End Cuts ..................................................................................................... 231
Snip End Cuts ..................................................................................................................................... 232
Cut Back End Cuts .............................................................................................................................. 236
End-to-End End Cuts .......................................................................................................................... 237
Long Box End Cuts ............................................................................................................................. 246
Miter End Cuts .................................................................................................................................... 247
Bounded by Plate ER .......................................................................................................................... 248
Optional Flange Cut Shapes ............................................................................................................... 248

Member End Cuts .................................................................................................................................... 250

Along-Axis Web Cuts for Members ..................................................................................................... 250
Web-penetrated Center Cuts ....................................................................................................... 251
Web-penetrated Top Cuts ............................................................................................................ 257
Web-penetrated Bottom Cuts ....................................................................................................... 264
Web Non-penetrated Cuts ............................................................................................................ 271
Along-Axis Flange Cuts for Members ................................................................................................. 273
Flange-penetrated Center Cuts .................................................................................................... 273
Flange-penetrated Top Cuts ........................................................................................................ 277
Flange-penetrated Bottom Cuts ................................................................................................... 289
Flange Non-penetrated Cuts ........................................................................................................ 297
Web Cuts for Split Members ............................................................................................................... 301
Flange Cuts for Split Members ........................................................................................................... 306
Mitered Web Cuts for Members .......................................................................................................... 307
Mitered Flange Cuts for Members ...................................................................................................... 308
Free-end Web Cuts for Members ....................................................................................................... 309
Free-end Flange Cuts for Members .................................................................................................... 311

Slots .......................................................................................................................................................... 313

Style 1 ................................................................................................................................................. 313
Slot C .................................................................................................................................................. 314
Slot I .................................................................................................................................................... 315

Sketched Features ................................................................................................................................... 326

Openings .................................................................................................................................................. 328

CircleOpening ..................................................................................................................................... 328

Intergraph Smart® 3D 2D Symbols Reference Data Guide 6

 Contents

OvalOpening ....................................................................................................................................... 329

RectangleOpening .............................................................................................................................. 329
SketchOpening.................................................................................................................................... 329
SquareOpening ................................................................................................................................... 330
TriangleOpening.................................................................................................................................. 330

Structural Manufacturing ........................................................................................................................ 331

Manufacturing Requirements for Profile Cross Sections .................................................................... 332
Manufacturing Requirements for Member Cross Sections ................................................................. 333
Bevel ................................................................................................................................................... 334
Bevel1 (I-Type).................................................................................................................................... 334
Bevel2 (V-Type) .................................................................................................................................. 335
Bevel3 (V-Type) .................................................................................................................................. 335
Bevel4 (X-Type) .................................................................................................................................. 335
Bevel5 (Y-Type) .................................................................................................................................. 335
Bevel6 (X-Type with Chamfer) ............................................................................................................ 335
Bevel7 (X-Type with Chamfer) ............................................................................................................ 336
Bevel8 (X-Type with Chamfer) ............................................................................................................ 336
Bevel9 (X-Type with Chamfer) ............................................................................................................ 336
Bevel10 ............................................................................................................................................... 336
BevelA ................................................................................................................................................. 337
BevelB ................................................................................................................................................. 337
BevelParam......................................................................................................................................... 338
FeatureTab1........................................................................................................................................ 338
Grind ................................................................................................................................................... 338
Knuckle ............................................................................................................................................... 339
Margin ................................................................................................................................................. 339
PartCenterLL ....................................................................................................................................... 339
PartDirC .............................................................................................................................................. 340
PartDirCL ............................................................................................................................................ 340
PartDirCR ............................................................................................................................................ 340
PartDirL ............................................................................................................................................... 341
PartDirLL ............................................................................................................................................. 341
PartDirLLFlangeRR ............................................................................................................................. 341
PartDirR .............................................................................................................................................. 342
PartDirRR ............................................................................................................................................ 342
PartDirRRFlangeLL ............................................................................................................................. 342
PMFeature .......................................................................................................................................... 343
Shrinkage ............................................................................................................................................ 343
SMPlateTab ........................................................................................................................................ 343
UnSpecBevel ...................................................................................................................................... 344
WeldTab1 ............................................................................................................................................ 344

Index ......................................................................................................................................................... 345

Intergraph Smart® 3D 2D Symbols Reference Data Guide 7

Preface
This document is a reference data guide for the Intergraph Smart® 3D 2D Symbols task. The
purpose of this document is to describe the reference data delivered with the software for this
task.
Reference data includes both catalog data and specification data. Catalog data includes the
parts that you place in the model, such as piping components and equipment. Specification data
includes the rules that govern how those parts are placed and connected.

Documentation Comments
For the latest support information for this product, comments or suggestions about this
documentation, and documentation updates for supported software versions, please visit
Intergraph Smart® Support (https://smartsupport.intergraph.com).

What's New in 2D Symbols Reference Data

The following changes have been made to the 2D symbols reference data.
Version 2018 (12.0)
 Added information about new structural detailing symbols. For more information, see Profile
End Cuts. (P2 CP:318257)

Intergraph Smart® 3D 2D Symbols Reference Data Guide 8

SECTION 1

2D Symbols Reference Data

The 2D Symbols utility is delivered with the software and is used to create symbols representing
profile cross-sections, brackets, slots, collars, end cuts, detailing features, and manufacturing
features in the Molded Forms and Structural Detailing tasks; member cross-sections in the
Structure task; and facilitate using these symbols in a modeling environment.
This document describes all of the 2D symbols that are delivered with the software. The symbol
library is delivered to the SharedContent share in the [Reference Data Product
Folder]\SharedContent folder
You can create your own custom symbols using the 2D Symbols utility. To learn how to create
2D symbols, refer to the 2D Symbols User's Guide.
Two sets of 2D symbols are delivered: default and marine library. The default
set contains basic symbols suitable for prototyping. The marine library set provides a more
complete set of marine symbols.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 9

SECTION 2

Bracket Symbols
Bracket symbols are delivered in two locations:
 [Reference Data Folder]\SharedContent\MarineLibrary\Brackets folder. Within the Brackets
folder, the folder hierarchy is further organized by the number of supports and by whether
the bracket is trimmed or lapped.
 [Reference Data Folder]\SharedContent\Brackets folder. Within the Brackets folder, the
folder hierarchy is further organized by the number of supports.

In This Section
2S Brackets ................................................................................... 10
2S Integrated Brackets .................................................................. 13
3S Brackets ................................................................................... 14
3S Flanged Brackets ..................................................................... 18
4S Brackets ................................................................................... 19
5S Brackets ................................................................................... 21

2S Brackets
2S brackets have two supports. Brackets can be trimmed or lapped to one or both supports.
The following 2S bracket symbols are delivered in the [Reference Data
Folder]\SharedContent\Marine Library\Brackets\2S folder.

Name Description Parameters

2SCL_1Lap Curved free edge

Support 1 is lapped

Intergraph Smart® 3D 2D Symbols Reference Data Guide 10

 Bracket Symbols

Name Description Parameters

2SCL_2Lap Curved free edge

Both supports are
lapped

2SCT Curved free edge

Trimmed to supports

2SLL_1Lap Linear free edge

Support 1 is lapped

Intergraph Smart® 3D 2D Symbols Reference Data Guide 11

 Bracket Symbols

Name Description Parameters

2SLL_2Lap Linear free edge

Both supports are
lapped

2SLT Linear free edge

Trimmed to supports

2SLTMem

Intergraph Smart® 3D 2D Symbols Reference Data Guide 12

 Bracket Symbols

Name Description Parameters

RibConnFlange

2S Integrated Brackets
2S integrated brackets have two supports. Brackets can be trimmed or lapped to one or both
supports.
The following 2S bracket symbols are delivered in the [Reference Data
Folder]\SharedContent\Marine Library\Brackets\2S\Integrated folder.

Name Description Parameters

2SC Curved free edge

Trimmed to supports

2SL Linear free edge

Trimmed to supports

Intergraph Smart® 3D 2D Symbols Reference Data Guide 13

 Bracket Symbols

3S Brackets
3S brackets have three supports.
3S bracket symbols are delivered in the [Reference Data Folder]\SharedContent\Marine
Library\Brackets\3S\Integrated folder.

Name Description Parameters

3SC Curved free edge

Offset

3SC Linear free edge

OffsetFromFlange

3SC Curved free edge

SetBack

Intergraph Smart® 3D 2D Symbols Reference Data Guide 14

 Bracket Symbols

Name Description Parameters

3SC
Symmetry

3SLC_FB

3SLC
SetBackFar

Intergraph Smart® 3D 2D Symbols Reference Data Guide 15

 Bracket Symbols

Name Description Parameters

3SL Linear free edge with

FlangeInFillet radius at Support 3,
offset to clear the
flange

3SL Linear free edge with

FlangeOutFillet radius at Support 3

3SL Linear free edge

Offset

3SL Linear free edge

OffsetFromFlange

Intergraph Smart® 3D 2D Symbols Reference Data Guide 16

 Bracket Symbols

Name Description Parameters

3SL Linear free edge

SetBack

3SL
SetBackFar

3SL
ToFlange

SC
OffsetFromFlange

Intergraph Smart® 3D 2D Symbols Reference Data Guide 17

 Bracket Symbols

3S Flanged Brackets
3S flanged brackets have three supports and a flange on the linear free edge.

3S flanged bracket symbols are delivered in the [Reference Data Folder]\SharedContent\Marine

Library\Brackets\Flanged\StdFlange\3S folder.

Name Description Parameters

3SLT Trimmed to supports

ToFlange

3SLT Trimmed to supports

FlangeOutFillet

Intergraph Smart® 3D 2D Symbols Reference Data Guide 18

 Bracket Symbols

Name Description Parameters

3SLT Trimmed to supports

FlangeInFillet

3SLLS2 Lapped to Support 2

OffsetFromFlange

Intergraph Smart® 3D 2D Symbols Reference Data Guide 19

 Bracket Symbols

4S Brackets
4S brackets have four supports. Brackets can be trimmed or lapped to Support1 and Support2,
but are trimmed to Support3 and Support4.
The following 4S bracket symbols are delivered in the [Reference Data
Folder]\SharedContent\Marine Library\Brackets\4S\Trimmed folder.

Name Description Parameters

4SCLT_OT

4SLCL

4SLCL_SBS3

Intergraph Smart® 3D 2D Symbols Reference Data Guide 20

 Bracket Symbols

Name Description Parameters

4SLCL_SBS4

5S Brackets
5S brackets have four supports. Brackets can be trimmed to all supports.
The following 5S bracket symbols are delivered in the [Reference Data
Folder]\SharedContent\MarineLibrary\Brackets\5S\Trimmed folder.

Name Parameters

5SCLT_OT

5SLCL

Intergraph Smart® 3D 2D Symbols Reference Data Guide 21

 Bracket Symbols

Name Parameters

5SLCL_SBS4

5SLCL_SBS5

Intergraph Smart® 3D 2D Symbols Reference Data Guide 22

SECTION 3

Flange Contours for Brackets

Flange contour symbols are used with flanged bracket symbols. Flange contour symbols are
delivered in the [Reference Data Folder]\SharedContent\Marine Library\Flange Contours folder.

Standard Bracket Flange Contour

Intergraph Smart® 3D 2D Symbols Reference Data Guide 23

SECTION 4

Chamfers
The chamfer symbols are delivered with the software in the SharedContent share in the
[Reference Data Folder]\SharedContent\FTLIBRARY\Chamfer folder.

Double Sided Style1 Chamfer

Intergraph Smart® 3D 2D Symbols Reference Data Guide 24

 Chamfers

Single Sided Style 1 Chamfers

SingleSidedBase

SingleSidedOffset

Intergraph Smart® 3D 2D Symbols Reference Data Guide 25

SECTION 5

Collars and Clips

Collar and clip symbols are delivered in two locations:
 [Reference Data Folder]\SharedContent\Marine Library\Collars folder.
 [Reference Data Folder]\SharedContent\Collars folder.

In This Section
Non-Tight Clips .............................................................................. 26
Tight Collars ................................................................................... 30

Non-Tight Clips
Clips are open on at least one side of the slot.
The following clip symbols are delivered in the [Reference Data Folder]\SharedContent\Marine
Library\Collars folder.

Name Cross- Selection Logic in Parameters

Sections the Rules
Supported

ClipAA_SM All Clip A

Non-tight
SlotA or Slot C
Profile height ≥
200mm (EA, UA,
FB, BUT, BUTL2)
Profile height ≥
180mm (B)

Intergraph Smart® 3D 2D Symbols Reference Data Guide 26

 Collars and Clips

Name Cross- Selection Logic in Parameters

Sections the Rules
Supported

ClipAAC_BT All Default selection for

(curved top) all cross-sections
ClipAAC_ST Clip C
(straight top)
Non-tight
SlotA or Slot C
Profile height ≥
100mm (EA, UA,
FB, BUT, BUTL2)
Profile height ≥
180mm (B)

ClipAAC_BT_Left EA Collar
Order=Secondary
UA
25 < SlotAngle < 65
BUT
(deg)
BUTL2
Available in ClipC
B
FB

ClipAAC_ST_S EA 0.1 < SlotAngle <

25 (deg)
UA
Available in ClipC
BUT
BUTL2

Intergraph Smart® 3D 2D Symbols Reference Data Guide 27

 Collars and Clips

Name Cross- Selection Logic in Parameters

Sections the Rules
Supported

ClipAAC_ST_Left Collar
Order=Secondary
SlotAngle < 0.1
(deg)
Available in ClipC

ClipAAC_ST_S_Left Collar
Order=Secondary
0.1 < SlotAngle <
25 (deg)
Available in ClipC

ClipAB_SM EA Available in ClipB

UA
B
BUT
FB
BUTL2

Intergraph Smart® 3D 2D Symbols Reference Data Guide 28

 Collars and Clips

The following clip symbols are delivered in the [Reference Data Folder]\SharedContent\Collars
folder.

Name Parameters

ClipAA
Clip BA

Clip AB
Clip BB

Clip AAC
Clip BAC

Intergraph Smart® 3D 2D Symbols Reference Data Guide 29

 Collars and Clips

Name Parameters

Clip ABC
Clip BBC

Tight Collars
Collars are welded around all sides of the slot.
The following collar symbols are delivered in the [Reference Data Folder]\SharedContent\Marine
Library\Collars folder.

Name Cross- Selection Logic in the Parameters

Sections Rules
Supported

CollarAIT_SM EA CollarNoSnipe
UA Tight
Slot I
CollarTIT_SM BUT
BUTL2

CollarACT_SM EA CollarOneSnipe
UA Tight
Slot C
CollarBCT_SM B

CollarFCT_SM FB

CollarTCT_SM BUT
BUTL2

Intergraph Smart® 3D 2D Symbols Reference Data Guide 30

 Collars and Clips

Name Cross- Selection Logic in the Parameters

Sections Rules
Supported

CollarACT_A EA CollarOneSnipe
UA Tight
Slot C
CollarBCT_A B (SlotXC_LT_PAT)

CollarFCT_A FB

CollarACT_A2 EA CollarOneSnipe
UA Tight
Slot C
CollarBCT_A2 B (SlotXC_LT_PAT2)

CollarFCT_A2 FB

CollarBCT_A3 B CollarOneType
Available when
Slot=SlotBC_L_LTT_STR

Intergraph Smart® 3D 2D Symbols Reference Data Guide 31

 Collars and Clips

Name Cross- Selection Logic in the Parameters

Sections Rules
Supported

CollarTCT_A BUT CollarOneSnipe

(right side)
BUTL2 Tight
CollarTCT_B
Slot C2
(left side)
(SlotXC2_T_PTT_STR)

CollarTCT_A2 BUT CollarOneSnipe

(right side)
BUTL2 Tight
CollarTCT_B2
EA Slot C2
(left side)
(SlotXC2_T_PTT_STR2)
UA

ClipType=CollarOneType

CollarTCT_A3 Available when Slot =

SlotTC2_T_PAA_STR
and CollarOrder = Primary
BUT
ClipType=CollarOneType
Available when Slot =
CollarTCT_B3 SlotTC2_T_PAA_STR
and CollarOrder =
Secondary

CollarAAT_SM EA CollarTwoSnipes
UA Tight
Slot A
CollarBAT_SM B

Intergraph Smart® 3D 2D Symbols Reference Data Guide 32

 Collars and Clips

Name Cross- Selection Logic in the Parameters

Sections Rules
Supported

CollarFAT_SM FB

CollarTAT_SM BUT
BUTL2

The following collar symbols are delivered in the [Reference Data Folder]\SharedContent\Collars
folder.

Name Parameters

Collar AIT

Collar FIT

Intergraph Smart® 3D 2D Symbols Reference Data Guide 33

 Collars and Clips

Name Parameters

Collar TIT

Collar TsIT

Collar ACT

Intergraph Smart® 3D 2D Symbols Reference Data Guide 34

 Collars and Clips

Name Parameters

Collar BCT

Collar FCT

Intergraph Smart® 3D 2D Symbols Reference Data Guide 35

 Collars and Clips

Name Parameters

Collar AAT

Collar BAT

Intergraph Smart® 3D 2D Symbols Reference Data Guide 36

 Collars and Clips

Name Parameters

Collar FAT

Collar TAT

Collar TsAT

Intergraph Smart® 3D 2D Symbols Reference Data Guide 37

 Collars and Clips

Name Parameters

Collar LAT

Intergraph Smart® 3D 2D Symbols Reference Data Guide 38

SECTION 6

Corner Features for Plates and

Stiffeners
The following corner feature symbols are delivered in the [Reference Data Product
Folder]\SharedContent\FTLIBRARY\Corner Features and [Reference Data Product
Folder]\SharedContent\Corner Features folders.

Name Description Parameters

Plate_Snipe Available in
PlateCornerFeature
as an default item
Default parameter:
ULength=10mm
VLength=10mm
Parameter Rule:

FTPlateCorner.SnipP
arm
SymbolFileName:
(FTLIBRARY)
Snipe_Plate.sym

Plate_C10 Available in
PlateCornerFeature
as an optional item.
Default parameter:
ULength=10mm
VLength=10mm
Parameter Rule:
FTPlateCorner.SnipP
arm
SymbolFileName:
(FTLIBRARY)
Snipe_Plate.sym

Intergraph Smart® 3D 2D Symbols Reference Data Guide 39

 Corner Features for Plates and Stiffeners

Name Description Parameters

Plate_C15 Available in
PlateCornerFeature
as an optional item.
Default parameter:
ULength=15mm
VLength=15mm
Parameter Rule:
FTPlateCorner.SnipP
arm
SymbolFileName:
(FTLIBRARY)
Snipe_Plate.sym

Plate_C20 Available in
PlateCornerFeature
as an optional item.
Default parameter:
ULength=20mm
VLength=20mm
Parameter Rule:
FTPlateCorner.SnipP
arm
SymbolFileName:
(FTLIBRARY)
Snipe_Plate.sym

Plate_Scallop Available in
PlateCornerFeature
as an optional item.
Default parameter:
Radius is changed in
different cases
Parameter Rule:
FTPlateCorner.PlScal
lopParm
SymbolFileName:
(FTLIBRARY)
Scallop_Plate.sym

Intergraph Smart® 3D 2D Symbols Reference Data Guide 40

 Corner Features for Plates and Stiffeners

Name Description Parameters

Plate_R35_Scallop Available in
PlateCornerFeature
as an optional item.
Default parameter:
Radius=35mm
Parameter Rule:
None
SymbolFileName:
(FTLIBRARY)
Scallop_Plate.sym

Plate_R50_Scallop Available in
PlateCornerFeature
as an optional item.
Default parameter:
Radius=50mm
Parameter Rule:
None
SymbolFileName:
(FTLIBRARY)
Scallop_Plate.sym

Plate_R75_Scallop Available in
PlateCornerFeature
as an optional item.
Default parameter:
Radius=75mm
Parameter Rule:
None
SymbolFileName:
(FTLIBRARY)
Scallop_Plate.sym

Plate_R38_Scallop Available in
PlateCornerFeature
as an optional item.
Default parameter:
Radius=38mm
Parameter Rule:
None
SymbolFileName:
(FTLIBRARY)
Scallop_Plate.sym

Intergraph Smart® 3D 2D Symbols Reference Data Guide 41

 Corner Features for Plates and Stiffeners

Name Description Parameters

Plate_R100_Scallop Available in
PlateCornerFeature
as an optional item.
Default parameter:
Radius=100mm
Parameter Rule:
None
SymbolFileName:
(FTLIBRARY)
Scallop_Plate.sym

Plate_LongScallop Available in
PlateCornerFeature
as an optional item.
Default parameter:
Radius=50mm
ULength=100mm
(If there is a seam,
ULength is related to
distance to seam)
Parameter Rule:
FTPlateCorner.LScall
opParm
SymbolFileName:
(FTLIBRARY)
LongScallop_Plate.sy
m

Plate_50R_LongScallop Default parameter:

Radius=50mm
LongScallop
ULength= 35mm from
is only selected when
seam
seam is near the corner.
If there is a seam,
ULength is related to
distance to seam.
Parameter Rule:
FTPlateCorner.LScall
opParm
SymbolFileName:
(FTLIBRARY)
LongScallop_Plate.sy
m

Intergraph Smart® 3D 2D Symbols Reference Data Guide 42

 Corner Features for Plates and Stiffeners

Name Description Parameters

Plate_35R_ LongScallop Default parameter:

Radius=35mm
LongScallop
ULength= 35mm from
is only selected when
seam
seam is near the corner.
If there is a seam,
ULength is related to
distance to seam.
Parameter Rule:
FTPlateCorner.LScall
opParm
SymbolFileName:
(FTLIBRARY)
LongScallop_Plate.sy
m

Plate_LP Available in
PlateCornerFeature
as an optional item.
Default parameter:
Radius=30mm
ULength=175mm
VLength=55mm
Offset=80mm
Parameter Rule:
FTPlateCorner.PlLPP
arm
SymbolFileName:
(FTLIBRARY)
LP.sym

Plate_LongScallop_2 Available in
PlateCornerFeature
as an optional item.
Default parameter:
Radius=50mm
ULength=Radius +
distanceToSeam
Parameter Rule:
FTPlateCorner.LScall
opParm2
SymbolFileName:
(FTLIBRARY)
LongScallop_Plate_2.
sym

Intergraph Smart® 3D 2D Symbols Reference Data Guide 43

 Corner Features for Plates and Stiffeners

Name Description Parameters

Plate_KE Available in
PlateCornerFeature
as an optional item.
Default parameter:
Vlength=10mm
OffsetV=15mm
OffsetU=15mm
Angle=13deg
Other parameters are
changed in different
cases.
Parameter Rule:
FTPlateCorner.PlKEP
arm
SymbolFileName:
(FTLIBRARY)
KE.sym

Plate_RN Available in
PlateCornerFeature
as an optional item.
Default parameter:
Angle=30deg
Other parameters are
changed in different
cases.
Parameter Rule:
FTPlateCorner.PlRN
Parm
SymbolFileName:
(FTLIBRARY)
RN.sym

Intergraph Smart® 3D 2D Symbols Reference Data Guide 44

 Corner Features for Plates and Stiffeners

Name Description Parameters

Plate_RC Available in
PlateCornerFeature
as an optional item.
Default parameter:
Radius=20mm
Radius2=30mm
ULength=25mm
VLength=70mm
OffsetV=15mm
OffsetU=15mm
Offset=19mm
Angle=30deg
Angle2=30deg
Parameter Rule:
FTPlateCorner.PlRC
Parm
SymbolFileName:
(FTLIBRARY)
RC.sym

Plate_WS_LongScallop Available in
PlateCornerFeature
as an optional item.
Default parameter:
Radius=50mm
ULength=Radius +
distanceToSeam
Parameter Rule:
FTPlateCorner.LScall
opParm2
SymbolFileName:
(FTLIBRARY)
LongScallop_Plate_2.
sym

Plate_WS_R75 Available in
PlateCornerFeature
as an optional item.
Default parameter:
Radius=75mm
Parameter Rule:
None
SymbolFileName:
(FTLIBRARY)
Scallop_Plate.sym

Intergraph Smart® 3D 2D Symbols Reference Data Guide 45

 Corner Features for Plates and Stiffeners

Name Description Parameters

Plate_WS_Scallop Available in
PlateCornerFeature
as an optional item.
Default parameter:
Radius=50mm
Parameter Rule:
None
SymbolFileName:
(FTLIBRARY)
Scallop_Plate.sym

Plate_35R_LongScallop Available in
PlateCornerFeature
as an optional item.
Default parameter:
Radius=35mm
ULength=100mm
If there is a seam,
ULength is related to
distance to seam.
Parameter Rule:
FTPlateCorner.LScall
opParm
SymbolFileName:
(FTLIBRARY)
LongScallop_Plate.sy
m

Plate_50R_LongScallop Available in
PlateCornerFeature
as an optional item.
Default parameter:
Radius=50mm
ULength=100mm
If there is a seam,
ULength is related to
distance to seam.
Parameter Rule:
FTPlateCorner.LScall
opParm
SymbolFileName:
(FTLIBRARY)
LongScallop_Plate.sy
m

Intergraph Smart® 3D 2D Symbols Reference Data Guide 46

 Corner Features for Plates and Stiffeners

Name Description Parameters

STI_Snipe Available in
StiffenerCornerFeatur
e
Default parameter:
ULength & VLength
are changed in
different cases.
Parameter Rule:
FTSTICorner.STISnip
Parm
SymbolFileName:
(FTLIBRARY)
Snipe.sym

STI_Scallop Available in
StiffenerCornerFeatur
e
Default parameter:
Radius is changed in
different cases.
Parameter Rule:
FTSTICorner.STIScal
lopParm
SymbolFileName:
(FTLIBRARY)
Scallop.sym

STI_LongScallop Available in
StiffenerCornerFeatur
e
Default parameter:
Radius & ULength
are changed in
different cases.
Parameter Rule:
FTSTICorner.STILSc
allopParm
SymbolFileName:
(FTLIBRARY)
LongScallop.sym

Intergraph Smart® 3D 2D Symbols Reference Data Guide 47

 Corner Features for Plates and Stiffeners

Name Description Parameters

STI_LongScallop_2 Availablein
StiffenerCornerFeatur
e as an optionalitem.
Default parameter:
Radius=35mm
ULength=Radius +
distanceToSeam
OffsetFromSupport1=
75mm
Parameter Rule:
FTSTICorner.STILSc
allopParm2
SymbolFileName:
(FTLIBRARY)
LongScallop_2.sym

Intergraph Smart® 3D 2D Symbols Reference Data Guide 48

SECTION 7

Corner Features for Members

The following corner feature symbols are delivered in the [Reference Data Product
Folder]\SharedContent\Marine Library\Corner Features and [Reference Data Product
Folder]\SharedContent\Corner Features folders.

Name Description Parameters

Arc Corner Relief Provides a minimal fit-up

clearance at a corner of the
bounding edge. When the
bounded object is within the
bounding object, the corner
feature may only be placed
at the inside corner. When
the bounded object extends
outside the bounding object,
the corner feature may also
be placed on the outside
corner.

Corner To Far Face Clears material from the

Edge Relief bounding edge and around
one corner. It is typically
applied to the inside corner
to relieve the outside corner.
The reverse is also possible.
This feature is applicable
when the bounded object
extends outside the
bounding object.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 49

 Corner Features for Members

Name Description Parameters

Edge Hook Relief Disconnects the bounded

object from the inside of the
bounding edge.

Edge To Face Rathole Provides welding access to

the back side of the bounded
flange or web.
This feature is applicable
when there is no bounding
edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 50

 Corner Features for Members

Name Description Parameters

Face To Inside Rathole Provides welding access to

2 the back side of the bounded
flange or web and
disconnects the member
from the inside of the
bounding edge.

This feature is applicable

when the inner surface of
the bounded flange/web is
outside the inner surface of
the bounded edge.

Fillet Ellipse Trims the bounded part

along the bounding fillet.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 51

 Corner Features for Members

Name Description Parameters

In Out Hook Relief Clears all material from the

bounding edge and in the
vicinity of both corners.

Outside Hook Relief Disconnects the bounding

object from the bounded
edge and the inner surface
of the bounding edge, while
leaving it connected to the
outside face.
This feature is applicable
when bounded object
extends outside the
bounding object.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 52

 Corner Features for Members

Name Description Parameters

Short Edge Rathole Provides welding access to

the back side of the bounded
flange or web.
This feature is applicable
when the inner surface of
the bounded flange/web is
significantly outside the inner
surface of the bounded
edge.

Two Edge Rathole Provides welding access to

the back side of the bounded
flange or web and
disconnect the member from
the inside of the bounding
edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 53

SECTION 8

Member Cross Sections

Member cross-section symbols are used in the Structure task.
All section tables delivered with the software use a specific set of cross-section symbols. Some
section tables use all the cross-section symbols in the set; some tables only use a subset of the
cross-section symbols. Each cross-section symbol has its own set of properties. When looking
at a section table workbook, you can determine the cross-section symbol that is being
referenced by that particular sheet by looking at the SymbolDefinition entry at the top of the
sheet.
The cross-section symbols are delivered with the reference data software in the [Reference
Data Folder]\SharedContent\CrossSections folder. You can create your own custom cross-
section symbols, sometimes referred to as arbitrary sections, using the 2D Symbols utility that is
delivered with the software.
The software uses the simple physical representation of the cross-section symbol to display the
member geometry in the model. You can change the display representation using the Selected
Aspects option of Format > View.
The delivered symbols contain a detailed physical representation. This representation is
available only for marine models, and is not used for plant and materials handling models.
The delivered symbols also contain a production physical representation. This representation is
available only for marine models in the Structural Manufacturing task, and is not used for plant
and materials handling models.
For more information, see Cross-Section Symbol Representations in the 2D Symbols User's
Guide.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 54

 Member Cross Sections

In This Section
Cross Section Symbol 2L .............................................................. 55
Cross Section Symbol BUBoxFM .................................................. 59
Cross Section Symbol BUC ........................................................... 62
Cross Section Symbol BUCan ....................................................... 65
Cross Section Symbol BUCone ..................................................... 68
Cross Section Symbol BUEndCan ................................................ 70
Cross Section Symbol BUFlat ....................................................... 72
Cross Section Symbol BUI ............................................................ 75
Cross Section Symbol BUIHaunch ................................................ 77
Cross Section Symbol BUITaperWeb ........................................... 80
Cross Section Symbol BUIUE ....................................................... 83
Cross Section Symbol BUL ........................................................... 86
Cross Section Symbol BUT ........................................................... 89
Cross Section Symbol BUTube ..................................................... 91
Cross Section Symbol C (MC) ....................................................... 93
Cross Section Symbol CS ............................................................. 96
Cross Section Symbol HSSC (Pipe) .............................................. 98
Cross Section Symbol HSSCs ...................................................... 100
Cross Section Symbol HSSR ........................................................ 102
Cross Section Symbol HSSRs ...................................................... 105
Cross Section Symbol HW ............................................................ 108
Cross Section Symbol HWWF....................................................... 110
Cross Section Symbol L ................................................................ 112
Cross Section Symbol Rect ........................................................... 116
Cross Section Symbol RectC ........................................................ 118
Cross Section Symbol RectCWF................................................... 120
Cross Section Symbol RectWF ..................................................... 123
Cross Section Symbol RS ............................................................. 125
Cross Section Symbol S ................................................................ 127
Cross Section Symbol ST .............................................................. 130
Cross Section Symbol T (MT) ....................................................... 132
Cross Section Symbol W (M) ........................................................ 135
Cross Section Symbol Wedge ....................................................... 138
Cross Section Symbol WedgeWF ................................................. 141

Intergraph Smart® 3D 2D Symbols Reference Data Guide 55

 Member Cross Sections

Cross Section Symbol 2L

The 2L cross section symbol defines double-angle sections and uses the following properties.

Section Name
Type the section name. This name appears when you label members. The section name
must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id
Type the material group identification for the section.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length, pound per foot
(lbm/ft).
Area
Type the cross-sectional area for the section. The area is defined in square inches or square
millimeters.
Depth
Type the depth for the section (longer legs). The depth is defined in inches or millimeters.
d
Type the depth for the section (shorter legs). The depth is defined in inches or millimeters.
bf
Type the width of a single angle. The width is defined in inches or millimeters.
Width
Type the width of the entire section. The width is defined in inches or millimeters.
Perimeter
Type the outside perimeter of the section.
tf
Type the flange thickness for the section. The thickness is defined in inches or millimeters.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 56

 Member Cross Sections

tw
Type the web thickness for the section. The thickness is defined in inches or millimeters.
kdesign
Type the distance from outer face of the flange to the web toe of the fillet of the rolled shape
or the equivalent distance on the welded section.
kdetail
Type the distance from outer face of the flange to the web toe of the fillet of the rolled shape
or the equivalent distance on welded section.
bb
Type the back-to-back spacing on the section.
CentroidY
Type the centroid location along the y-axis. The location is defined in inches or millimeters.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant.
bb Configuration
Specifies which legs of the angles are placed back-to-back. Type 0 for equal leg angle. Type

Intergraph Smart® 3D 2D Symbols Reference Data Guide 57

 Member Cross Sections

1 to place the long legs back-to-back. Type 2 to place the short legs back-to-back.

lsg
Specify the bolt gage for the long side when there is one bolt row. For more information, see
Member Cross Sections.
lsg1
Specify the gage distance to the first bolt row on the long side when there are two bolt rows.
lsg2
Specify the gage distance between the first and second bolt rows on the long side when
there are two bolt rows.
ssg
Specify the bolt gage for the short side when there is one bolt row.
ssg1
Specify the gage distance to the first bolt row on the short side when there are two bolt
rows.
ssg2
Specify the gage distance from the first bolt row to the second bolt row on the short side
when there are two bolt rows.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is False.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is True.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 58

 Member Cross Sections

Cross Section Symbol BUBoxFM

The BUBoxFM symbol uses the following properties.

Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length, pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in meters.
Width
Type the width for the section. The width is defined in meters.
Perimeter
The outside perimeter distance for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 59

 Member Cross Sections

Top Flange Width

Type the width of the top flange.
Top Flange Thickness
Type the thickness of the top flange.
Bottom Flange Width
Type the width of the bottom flange.
Bottom Flange Thickness
Type the thickness of the bottom flange.
Web Thickness
Type the thickness of the web.
Offset Left Web Top
Type the offset distance for the top left web.
Offset Right Web Top
Type the offset distance for the top right web.
Offset Left Web Bot
Type the offset distance for the bottom left web.
Offset Right Web Bot
Type the offset distance for the bottom right web.
CentroidX
Type the vertical distance from designated member edge to the centroidal axis.
CentroidY
Type the vertical distance from designated member edge to the centroidal axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 60

 Member Cross Sections

Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is True.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section,
whether or not the cross-section is symmetrical about the x-axis depends on dimensional
values.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section,
whether or not the cross-section is symmetrical about the y-axis depends on dimensional
values.
Symmetries about the x- and y-axes are defined by design properties only. The
Flange Width Extension (top and bottom) property is not a design property; therefore, the
symmetry calculation is not affected by this property. This non-affect can cause
discrepancies between the symmetry of the cross-section graphic and the
IsSymmetricAlongX and IsSymmetricAlongY properties when non-zero width extensions
are defined.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 61

 Member Cross Sections

Cross Section Symbol BUC

The BUC symbol uses the following properties.

Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in meters
Width
Type the width for the section. The width is defined in meters.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 62

 Member Cross Sections

Perimeter
The outside perimeter distance for the section.
Top Flange Width
Type the width of the top flange.
Top Flange Thickness
Type the thickness of the top flange.
Bottom Flange Width
Type the width of the bottom flange.
Bottom Flange Thickness
Type the thickness of the bottom flange.
Web Thickness
Type the thickness of the web.
Offset Web Top
Type the offset distance for the top web.
Offset Web Bot
Type the offset distance for the bottom web.
CentroidX
Type the vertical distance from designated member edge to the centroidal axis.
CentroidY
Type the vertical distance from designated member edge to the centroidal axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 63

 Member Cross Sections

Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.

gf
Type the bolt gage for the flange.
gw
Type the bolt gage for the web.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section,
whether or not the cross-section is symmetrical about the x-axis depends on dimensional
values.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section,
whether or not the cross-section is symmetrical about the y-axis depends on dimensional
values.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 64

 Member Cross Sections

Cross Section Symbol BUCan

The BUCan symbol uses the following properties.

Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 65

 Member Cross Sections

Depth
Type the depth for the section. The depth is defined in meters
Width
Type the width for the section. The width is defined in meters.
Perimeter
The outside perimeter distance for the section.
Tube Thickness
Type the plate thickness of the main tube plate.
Tube Diameter
Type the diameter of the main tube.
Diameter Start
Type the cone diameter at the can start.
Diameter End
Type the cone diameter at the can end.
Length Start Cone
Type the start cone length. You can also type any negative number to indicate this length
should be 1/3 of the total length.
Length End Cone
Type the end cone length. You can also type any negative number to indicate this length
should be 1/3 of the total length.
Cone 1 Thickness
Type the plate thickness for the cone closest to the start of the member.
Cone 1 Material
Type the plate material for the cone closest to the start of the member.
Cone 1 Grade
Type the plate material grade for the cone closest to the start of the member.
Cone 2 Thickness
Type the plate thickness for the cone closest to the end of the member.
Cone 2 Material
Type the plate material for the cone closest to the end of the member.
Cone 2 Grade
Type the plate material grade for the cone closest to the end of the member.
CentroidX
Type the vertical distance from designated member edge to the centroidal axis.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 66

 Member Cross Sections

CentroidY
Type the vertical distance from designated member edge to the centroidal axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is True.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is True.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is True.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 67

 Member Cross Sections

Cross Section Symbol BUCone

The BUCone symbol uses the following properties.

Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in meters
Width
Type the width for the section. The width is defined in meters.
Perimeter
The outside perimeter distance for the section.
Cone Thickness
Type the plate thickness of the cone plate.
Diameter Start
Type the cone diameter at the start.
Diameter End
Type the cone diameter at the end.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 68

 Member Cross Sections

Length Start Cone

Type the start cone length. You can also type any negative number to indicate this length
should be 1/3 of the total length.
Length End Cone
Type the end cone length. You can also type any negative number to indicate this length
should be 1/3 of the total length.
CentroidX
Type the vertical distance from designated member edge to the centroidal axis.
CentroidY
Type the vertical distance from designated member edge to the centroidal axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 69

 Member Cross Sections

IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is True.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is True.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is True.

Cross Section Symbol BUEndCan

The BUEndCan symbol uses the following properties.

Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 70

 Member Cross Sections

Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in meters
Width
Type the width for the section. The width is defined in meters.
Perimeter
The outside perimeter distance for the section.
Tube Thickness
Type the plate thickness of the main tube plate.
Tube Diameter
Type the diameter of the main tube.
Diameter Cone
Type the cone diameter.
Cone Length
Type the start cone length. You can also type any negative number to indicate this length
should be 1/3 of the total length.
CentroidX
Type the vertical distance from designated member edge to the centroidal axis.
CentroidY
Type the vertical distance from designated member edge to the centroidal axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 71

 Member Cross Sections

Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is True.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is True.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is True.

Cross Section Symbol BUFlat

The BUFlat symbol uses the following properties.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 72

 Member Cross Sections

Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in meters
Width
Type the width for the section. The width is defined in meters.
Perimeter
The outside perimeter distance for the section.
Web Thickness
Type the thickness of the top flange.
CentroidX
Type the vertical distance from designated member edge to the centroidal axis.
CentroidY
Type the vertical distance from designated member edge to the centroidal axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 73

 Member Cross Sections

Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is True.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is True.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 74

 Member Cross Sections

Cross Section Symbol BUI

The BUI symbol uses the following properties.

Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in meters
Width
Type the width for the section. The width is defined in meters.
Perimeter
The outside perimeter distance for the section.
Top Flange Width
Type the width of the top flange.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 75

 Member Cross Sections

Top Flange Thickness

Type the plate thickness of the top flange.
Web Thickness
Type the thickness of the top flange.
CentroidX
Type the vertical distance from designated member edge to the centroidal axis.
CentroidY
Type the vertical distance from designated member edge to the centroidal axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 76

 Member Cross Sections

H
Type the flexural constant for the section.

gf
Type the bolt gage for the flange.
gw
Type the bolt gage for the web.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is True.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is True.

Cross Section Symbol BUIHaunch

The BUIHaunch symbol uses the following properties.

Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
Type the short name for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 77

 Member Cross Sections

EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in meters.
Width
Type the width for the section. The width is defined in meters.
Perimeter
The outside perimeter distance for the section.
Top Flange Width
Type the width of the top flange.
Top Flange Thickness
Type the plate thickness of the top flange.
Bottom Flange Width
Type the width of the bottom flange.
Bottom Flange Thickness
Type the plate thickness of the bottom flange.
Length Start
Type the distance from the start of the member to where the haunch transition should start.
You can type any negative number to indicate the distance should be 1/3 of the member
length.
Depth Start
Type the web depth at the start of the member.
Depth End
Type the web depth at the end of the member.
Depth Haunch
Type the web depth at the haunch.
Length End
Type the distance from the end of the member to where the haunch transition should end.
You can type any negative number to indicate the distance should be 1/3 of the member
length.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 78

 Member Cross Sections

Transition Gradient Start

Type the slope of the start transition.
Transition Gradient End
Type the slope of the end transition.
Web Thickness
Type the thickness of the top flange.
CentroidX
Type the vertical distance from designated member edge to the centroidal axis.
CentroidY
Type the vertical distance from designated member edge to the centroidal axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 79

 Member Cross Sections

IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section,
whether or not the cross-section is symmetrical about the x-axis depends on dimensional
values.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is True.
Symmetries about the x- and y-axes are defined by design properties only. The
Flange Width Extension (top and bottom) property is not a design property; therefore, the
symmetry calculation is not affected by this property. This non-affect can cause
discrepancies between the symmetry of the cross-section graphic and the
IsSymmetricAlongX and IsSymmetricAlongY properties when non-zero width extensions
are defined.

Cross Section Symbol BUITaperWeb

The BUITaperWeb symbol uses the following properties.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 80

 Member Cross Sections

Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in meters
Width
Type the width for the section. The width is defined in meters.
Perimeter
The outside perimeter distance for the section.
Top Flange Width
Type the width of the top flange.
Top Flange Thickness
Type the plate thickness of the top flange.
Bottom Flange Width
Type the width of the bottom flange.
Bottom Flange Thickness
Type the plate thickness of the bottom flange.
Web Thickness
Type the thickness of the top flange.
Depth Start
Type the web depth at the start of the member.
Depth End
Type the web depth at the end of the member.
CentroidX
Type the vertical distance from designated member edge to the centroidal axis.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 81

 Member Cross Sections

CentroidY
Type the vertical distance from designated member edge to the centroidal axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section,
whether or not the cross-section is symmetrical depends on dimensional values.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is True.
Symmetries about the x- and y-axes are defined by design properties only. The

Intergraph Smart® 3D 2D Symbols Reference Data Guide 82

 Member Cross Sections

Flange Width Extension (top and bottom) property is not a design property; therefore, the
symmetry calculation is not affected by this property. This non-affect can cause
discrepancies between the symmetry of the cross-section graphic and the
IsSymmetricAlongX and IsSymmetricAlongY properties when non-zero width extensions
are defined.

Cross Section Symbol BUIUE

The BUIUE symbol uses the following properties.

Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in meters

Intergraph Smart® 3D 2D Symbols Reference Data Guide 83

 Member Cross Sections

Width
Type the width for the section. The width is defined in meters.
Perimeter
The outside perimeter distance for the section.
Top Flange Width
Type the width of the top flange.
Top Flange Thickness
Type the plate thickness of the top flange.
Bottom Flange Width
Type the width of the bottom flange.
Bottom Flange Thickness
Type the plate thickness of the bottom flange.
Web Thickness
Type the thickness of the top flange.
Depth Start
Type the web depth at the start of the member.
Depth End
Type the web depth at the end of the member.
CentroidX
Type the vertical distance from designated member edge to the centroidal axis.
CentroidY
Type the vertical distance from designated member edge to the centroidal axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 84

 Member Cross Sections

Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.

gf
Type the bolt gage for the flange.
gw
Type the bolt gage for the web.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section,
whether or not the cross-section is symmetrical about the x-axis depends on dimensional
values.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is True.
Symmetries about the x- and y-axes are defined by design properties only. The
Flange Width Extension (top and bottom) property is not a design property; therefore, the
symmetry calculation is not affected by this property. This non-affect can cause
discrepancies between the symmetry of the cross-section graphic and the
IsSymmetricAlongX and IsSymmetricAlongY properties when non-zero width extensions
are defined.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 85

 Member Cross Sections

Cross Section Symbol BUL

The BUL symbol uses the following properties.

Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in meters
Width
Type the width for the section. The width is defined in meters.
Perimeter
The outside perimeter distance for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 86

 Member Cross Sections

Bottom Flange Width

Type the width of the bottom flange.
Bottom Flange Thickness
Type the plate thickness of the bottom flange.
Web Thickness
Type the thickness of the top flange.
Depth Start
Type the web depth at the start of the member.
Depth End
Type the web depth at the end of the member.
CentroidX
Type the vertical distance from designated member edge to the centroidal axis.
CentroidY
Type the vertical distance from designated member edge to the centroidal axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 87

 Member Cross Sections

ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.
lsg
Specify the bolt gage for the long side when there is one bolt row.
lsg1
Specify the gage distance to the first bolt row on the long side when there are two bolt rows.
lsg2
Specify the gage distance from the first bolt row to the second bolt row on the long side
when there are two bolt rows.

ssg
Specify the bolt gage for the short side when there is one bolt row.
ssg1
Specify the gage distance to the first bolt row on the short side when there are two bolt
rows.
ssg2
Specify the gage distance from the first bolt row to the second bolt row on the short side
when there are two bolt rows.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is False.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section,

Intergraph Smart® 3D 2D Symbols Reference Data Guide 88

 Member Cross Sections

whether or not the cross-section is symmetrical about the y-axis depends on dimensional
values.

Cross Section Symbol BUT

The BUT symbol uses the following properties.

Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in meters
Width
Type the width for the section. The width is defined in meters.
Perimeter
The outside perimeter distance for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 89

 Member Cross Sections

Top Flange Width

Type the width of the top flange.
Top Flange Thickness
Type the plate thickness of the top flange.
Web Thickness
Type the thickness of the top flange.
Depth Start
Type the web depth at the start of the member.
Depth End
Type the web depth at the end of the member.
CentroidX
Type the vertical distance from designated member edge to the centroidal axis.
CentroidY
Type the vertical distance from designated member edge to the centroidal axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 90

 Member Cross Sections

ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.

gf
Type the bolt gage for the flange.
gw
Type the bolt gage for the web.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is False.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is True.

Cross Section Symbol BUTube

The BUTube symbol uses the following properties.

Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
Type the short name for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 91

 Member Cross Sections

EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in meters
Width
Type the width for the section. The width is defined in meters.
Perimeter
The outside perimeter distance for the section.
Tube Thickness
Type the plate thickness of the tube plate.
Tube Diameter
Type the diameter of the tube.
CentroidX
Type the vertical distance from designated member edge to the centroidal axis.
CentroidY
Type the vertical distance from designated member edge to the centroidal axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 92

 Member Cross Sections

Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is True.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is True.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is True.

Cross Section Symbol C (MC)

The C cross-section symbol defines channel sections and uses the following properties. The C
symbol is also used for MC cross-sections.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 93

 Member Cross Sections

Section Name
Type the section name. This name appears when you label members. The section name
must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id
Type the material group identification for the section.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-sectional area for the section. The area is defined in square inches or square
millimeters.
Depth
Type the depth for the section. The depth is defined in inches or millimeters.
Width
Type the flange width for the section. The width is defined in inches or millimeters.
Perimeter
The outside perimeter distance for the section.
d
Type the depth for the section. The depth is defined in inches or millimeters.
If you are using StructCrossSections-Aust-05.xls data, then d = Depth - (2
* tf).
bf
Type the flange width for the section. The width is defined in inches or millimeters.
tw
Type the web thickness for the section. The thickness is defined in inches or millimeters.
tf
Type the flange thickness for the section. The thickness is defined in inches or millimeters.
kdesign
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on the welded section.
kdetail
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled

Intergraph Smart® 3D 2D Symbols Reference Data Guide 94

 Member Cross Sections

shape or the equivalent distance on welded section.

CentroidX
Type the centroid location along the x-axis. The location is defined in inches or millimeters.
eo_x
Type the shear center location along the x-axis. The location is defined in inches or
millimeters.
xp
Type the horizontal distance from the designated edge of member to its plastic neutral axis
(PNA). The distance is defined in inches or millimeters.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 95

 Member Cross Sections

H
Type the flexural constant in LRFD Specification Equation E3-1.

gf
Type the bolt gage for the flange.
gw
Type the bolt gage for the web.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is True.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is False.

Cross Section Symbol CS

The CS cross section symbol defines solid round sections and uses the following properties.

Section Name
Type the section name. This name appears when you label members. The section name
must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 96

 Member Cross Sections

Group Id
Type the material group identification for the section.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-sectional area for the section. The area is defined in square inches or square
millimeters.
Depth
Type the depth of the section.
Width
Type the width of the section.
Perimeter
Type the outside perimeter distance for the section.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is True.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the

Intergraph Smart® 3D 2D Symbols Reference Data Guide 97

 Member Cross Sections

default value is True.

Cross Section Symbol HSSC (Pipe)

The HSSC cross section symbol defines circular, hollow structural sections and uses the
following properties. The HSSC symbol is also used for Pipe cross-sections.

Section Name
Type the section name. This name appears when labeling members. The section name
must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id
Type the material group identification for the section.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section. The area is defined in square inches or square
millimeters.
Depth
Type the depth of the section.
Width
Type the width of the section.
Perimeter
The outside perimeter distance for the section.
tnom
Type the nominal wall thickness of the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 98

 Member Cross Sections

tdes
Type the design wall thickness of the section.
D_t
Type the ratio of the diameter to the thickness.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is True.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is True.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is True.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 99

 Member Cross Sections

Cross Section Symbol HSSCs

The HSSC cross section symbol defines circular, hollow structural sections and uses the
following properties. The HSSC symbol is also used for Pipe cross-sections.

Section Name
Type the section name. This name appears when labeling members. The section name
must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id
Type the material group identification for the section.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section. The area is defined in square inches or square
millimeters.
Depth
Type the depth of the section.
Width
Type the width of the section.
Perimeter
The outside perimeter distance for the section.
tnom
Type the nominal wall thickness of the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 100

 Member Cross Sections

tdes
Type the design wall thickness of the section.
D_t
Type the ratio of the diameter to the thickness.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is True.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is True.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is True.
Has Seam
Specify if the cross-section has a seam indicator or not. For this cross-section, the default

Intergraph Smart® 3D 2D Symbols Reference Data Guide 101

 Member Cross Sections

value is True (1).

Seam Angle
Defines the location of the seam. This angle is measured clockwise from orientation vector
of the member looking down the member from the start end.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 102

 Member Cross Sections

Cross Section Symbol HSSR

The HSSR cross section symbol defines rectangular, hollow, structural sections and uses the
following properties.

Section Name
Type the section name. This name appears when you label members. The section name
must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id
Type the material group identification for the section.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section. The area is defined in square inches and square
millimeters.
Depth
Type the overall depth of the section.
Width
Type the width for the section. The width is defined in inches or millimeters.
Perimeter
The outside perimeter distance for the section.
tnom
Type the nominal wall thickness of the section.
tdes
Type the design wall thickness of the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 103

 Member Cross Sections

b_t
Type the width to thickness ratio of the section.
h_t
Type the height to thickness ratio of the section.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is True
(1).
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is True (1).
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is True (1).

Intergraph Smart® 3D 2D Symbols Reference Data Guide 104

 Member Cross Sections

Cross Section Symbol HSSRs

The HSSRs cross section symbol defines rectangular, hollow, structural sections with a seam
indicator and uses the following properties.

Section Name
Type the section name. This name appears when you label members. The section name
must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id
Type the material group identification for the section.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section. The area is defined in square inches and square
millimeters.
Depth
Type the overall depth of the section.
Width
Type the width for the section. The width is defined in inches or millimeters.
Perimeter
The outside perimeter distance for the section.
tnom
Type the nominal wall thickness of the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 105

 Member Cross Sections

tdes
Type the design wall thickness of the section.
b_t
Type the width to thickness ratio of the section.
h_t
Type the height to thickness ratio of the section.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is True
(1).
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is True (1).
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is True (1).
Has Seam
Specify if the cross-section has a seam indicator or not. For this cross-section, the default

Intergraph Smart® 3D 2D Symbols Reference Data Guide 106

 Member Cross Sections

value is True (1).

Seam Angle
Defines the location of the seam. This angle is measured clockwise from orientation vector
of the member looking down the member from the start end.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 107

 Member Cross Sections

Cross Section Symbol HW

The HW symbol uses the following properties.

Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id
Type the material group identification for the section.
Angle
Define the angle.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in meters
Width
Type the width for the section. The width is defined in meters.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 108

 Member Cross Sections

Perimeter
The outside perimeter distance for the section.
d
Type the depth for the section.
bf
Type the width for the section.
tw
Type the web thickness for the section. The thickness is defined in meters.
tf
Type the flange thickness for the section. The thickness is defined in meters.
kdesign
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on the welded section.
kdetail
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on welded section.
CentroidY
Type the vertical distance from designated member edge to the centroidal axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 109

 Member Cross Sections

J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.

Cross Section Symbol HWWF

The HWWF symbol uses the following properties.

Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id
Type the material group identification for the section.
Angle
Define the angle.
Flange Right Width
Define the flange width on the right side.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 110

 Member Cross Sections

Flange Left Width

Define the flange width on the left side.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in meters
Width
Type the width for the section. The width is defined in meters.
Perimeter
The outside perimeter distance for the section.
d
Type the depth for the section.
bf
Type the width for the section.
tw
Type the web thickness for the section. The thickness is defined in meters.
tf
Type the flange thickness for the section. The thickness is defined in meters.
kdesign
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on the welded section.
kdetail
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on welded section.
CentroidX
Type the horizontal distance from the designated member edge to the centroidal axis.
CentroidY
Type the vertical distance from the designated member edge to the centroidal axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 111

 Member Cross Sections

Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.

Cross Section Symbol L

The L cross section symbol uses the following properties.

Section Name
Type the section name. This name appears when you label members. The section name
must be unique within the section standard.
Short Name
Type the short name for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 112

 Member Cross Sections

EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id
Type the material group identification for the section.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section. The area is defined in square inches or square
millimeters.
Depth
Type the depth for the section. The depth is defined in inches or millimeters.
Width
Type the breadth for the section. The breadth is defined in inches or millimeters.
Perimeter
The outside perimeter distance for the section.
d
Type the overall depth (longer leg) for the section. The depth is defined in inches or
millimeters.
If you are using StructCrossSections-Aust-05.xls data, then d = Depth -
tf.
bf
Type the overall width (shorter leg) for the section. The width is defined in inches or
millimeters.
tf
Type the flange thickness for the section. The thickness is defined in inches or millimeters.
tw
Type the web thickness for the section. The thickness is defined in inches or millimeters.
kdesign
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on the welded section.
kdetail
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on welded section.
CentroidX
Type the location of the centroid along the local x-axis. The location is defined in inches or
millimeters.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 113

 Member Cross Sections

CentroidY
Type the location of the centroid along the local y-axis. The location is defined in inches or
millimeters.
xp
Type the distance from the designated edge of angle to its plastic neutral axis (PNA) along
the local x-axis.
yp
Type the distance from the designated edge of angle to its plastic neutral axis (PNA) along
the local y-axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
Rxy
Type the radius of gyration about the local z-axis. The radius is defined in inches or
millimeters.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 114

 Member Cross Sections

lsg
Specify the bolt gage for the long side when there is one bolt row.
lsg1
Specify the gage distance to the first bolt row on the long side when there are two bolt rows.
lsg2
Specify the gage distance from the first bolt row to the second bolt row on the long side
when there are two bolt rows.

ssg
Specify the bolt gage for the short side when there is one bolt row.
ssg1
Specify the gage distance to the first bolt row on the short side when there are two bolt
rows.
ssg2
Specify the gage distance from the first bolt row to the second bolt row on the short side
when there are two bolt rows.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is False.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is False.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 115

 Member Cross Sections

Cross Section Symbol Rect

The Rect symbol uses the following properties.

Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id
Type the material group identification for the section.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in meters
Width
Type the width for the section. The width is defined in meters.
Perimeter
The outside perimeter distance for the section.
bf
Type the width for the section.
tw
Type the web thickness for the section. The thickness is defined in meters.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 116

 Member Cross Sections

tf
Type the flange thickness for the section. The thickness is defined in meters.
kdesign
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on the welded section.
kdetail
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on welded section.
CentroidX
Type the horizontal distance from the designated member edge to the centroidal axis.
CentroidY
Type the vertical distance from the designated member edge to the centroidal axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 117

 Member Cross Sections

H
Type the flexural constant for the section.

Cross Section Symbol RectC

The RectC symbol uses the following properties.

Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id
Type the material group identification for the section.
Angle
Define the angle.
Setback
Define the setback. This value is defined in meters.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 118

 Member Cross Sections

Depth
Type the depth for the section. The depth is defined in meters
Width
Type the width for the section. The width is defined in meters.
Perimeter
The outside perimeter distance for the section.
bf
Type the width for the section.
tw
Type the web thickness for the section. The thickness is defined in meters.
tf
Type the flange thickness for the section. The thickness is defined in meters.
kdesign
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on the welded section.
kdetail
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on welded section.
CentroidX
Type the horizontal distance from the designated member edge to the centroidal axis.
CentroidY
Type the vertical distance from the designated member edge to the centroidal axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 119

 Member Cross Sections

Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.

Cross Section Symbol RectCWF

The RectCWF symbol uses the following properties.

Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id
Type the material group identification for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 120

 Member Cross Sections

Angle
Define the angle.
Setback
Define the setback. This value is defined in meters.
Flange Right Width
Define the flange width on the right side. This valve is defined in meters.
Flange Left Width
Define the flange width on the left side. This valve is defined in meters.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in meters
Width
Type the width for the section. The width is defined in meters.
Perimeter
The outside perimeter distance for the section.
bf
Type the width for the section.
tw
Type the web thickness for the section. The thickness is defined in meters.
tf
Type the flange thickness for the section. The thickness is defined in meters.
kdesign
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on the welded section.
kdetail
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on welded section.
CentroidX
Type the horizontal distance from the designated member edge to the centroidal axis.
CentroidY
Type the vertical distance from the designated member edge to the centroidal axis.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 121

 Member Cross Sections

Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 122

 Member Cross Sections

Cross Section Symbol RectWF

The RectWF symbol uses the following properties.

Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id
Type the material group identification for the section.
Flange Right Width
Define the flange width on the right side. This valve is defined in meters.
Flange Left Width
Define the flange width on the left side. This valve is defined in meters.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in meters
Width
Type the width for the section. The width is defined in meters.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 123

 Member Cross Sections

Perimeter
The outside perimeter distance for the section.
d
Type the depth for the section.
bf
Type the width for the section.
tw
Type the web thickness for the section. The thickness is defined in meters.
tf
Type the flange thickness for the section. The thickness is defined in meters.
kdesign
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on the welded section.
kdetail
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on welded section.
CentroidY
Type the vertical distance from designated member edge to the centroidal axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 124

 Member Cross Sections

J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.

Cross Section Symbol RS

The RS cross section symbol defines rectangular solids and uses the following properties.

Section Name
Type the section name. This name appears when you label members. The section name
must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id
Type the material group identification for the section.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section. The area is defined in square inches and square
millimeters.
Depth
Type the depth for the section. The depth is defined in inches or millimeters.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 125

 Member Cross Sections

Width
Type the breadth for the section. The breadth is defined in inches or millimeters.
Perimeter
Type the outside perimeter distance for the section.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is True.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is True.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 126

 Member Cross Sections

Cross Section Symbol S

The S cross section symbol uses the following properties.

Section Name
Type the section name. This name appears when you label members. The section name
must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id
Type the material group identification for the section.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in inches.
Width
Type the flange width for the section. The width is defined in inches.
Perimeter
The outside perimeter distance for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 127

 Member Cross Sections

d
Type the overall depth for the section.
bf
Type the overall width for the section.
tw
Type the web thickness for the section. The thickness is defined in inches.
tf
Type the flange thickness for the section. The thickness is defined in inches.
kdesign
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on the welded section.
kdetail
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on welded section.
Fy3p
Type the maximum yield for the compact web for the section.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 128

 Member Cross Sections

Cw
Type the warping constant for the section.
Wno
Type the normalized warping function. The function is defined in square inches or square
millimeters.
Sw
Type the warping statical moment. The moment is defined in in4 or mm4.
Qf
Type the first moment of area for the flange.
Qw
Type the first moment of area for the web.

gf
Type the bolt gage for the flange.
gw
Type the bolt gage for the web.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is True.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is True.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 129

 Member Cross Sections

Cross Section Symbol ST

The ST cross section symbol uses the following properties.

Section Name
Type the section name. This name appears when you label members. The section name
must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id
Type the material group identification for the section.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in inches.
Width
Type the flange width for the section. The width is defined in inches.
Perimeter
The outside perimeter distance for the section.
d
Type the depth for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 130

 Member Cross Sections

bf
Type the width for the section.
tw
Type the web thickness for the section. The thickness is defined in inches.
tf
Type the flange thickness for the section. The thickness is defined in inches.
kdesign
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on the welded section.
kdetail
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on welded section.
CentroidY
Type the distance to the centroid along the local y-axis. This distance is defined in inches or
millimeters.
yp
Type the distance from the designated edge of angle to its plastic neutral axis along the
local y-axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 131

 Member Cross Sections

Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.

gf
Type the bolt gage for the flange.
gw
Type the bolt gage for the web.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is False.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is True.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 132

 Member Cross Sections

Cross Section Symbol T (MT)

The T cross-section symbol uses the following properties. The T symbol is also used for MT
cross-sections.

Section Name
Type the section name. This name appears when you label members. The section name
must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id
Type the material group identification for the section.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in inches.
Width
Type the flange width for the section. The width is defined in inches.
Perimeter
The outside perimeter distance for the section.
d
Type the depth for the section.
bf
Type the width for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 133

 Member Cross Sections

tw
Type the web thickness for the section. The thickness is defined in inches.
tf
Type the flange thickness for the section. The thickness is defined in inches.
kdesign
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on the welded section.
kdetail
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on welded section.
CentroidY
Type the vertical distance from designated member edge to the centroidal axis.
yp
Type the distance from designated edge of angle to its plastic neutral axis along the local y-
axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 134

 Member Cross Sections

ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.
gf
Type the bolt gage for the flange.
gw
Type the bolt gage for the web.

IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is False.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is True.

Cross Section Symbol W (M)

The W symbol uses the following properties. The W symbol is also used for M cross-sections.

Section Name
Type the section name. This name appears when you label members. The section name
must be unique within the section standard.
Short Name
Type the short name for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 135

 Member Cross Sections

Alternate EDI Name

Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id
Type the material group identification for the section.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in inches.
Width
Type the flange width for the section. The width is defined in inches.
Perimeter
The outside perimeter distance for the section.
d
Type the depth for the cross section. The depth is defined in inches or millimeters.
If you are using StructCrossSections-Aust-05.xls data, then d = Depth - (2
* tf).
bf
Type the width for the section.
tw
Type the web thickness for the section. The thickness is defined in inches.
tf
Type the flange thickness for the section. The thickness is defined in inches.
kdesign
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on the welded section.
kdetail
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on welded section.
Fy3p
Type the maximum yield stress for the section.
Ixx
Type the moment of inertia for the section's local x-axis.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 136

 Member Cross Sections

Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
Wno
Type the normalized warping function. The function is defined in square inches or square
millimeters.
Sw
Type the warping statical moment. The moment is defined in in4 or mm4.
Qf
Type the first moment of area for the flange.
Qw
Type the first moment of area for the web.

gf
Type the bolt gage for the flange.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 137

 Member Cross Sections

gw
Type the bolt gage for the web.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is True.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is True.

Cross Section Symbol Wedge

The Wedge symbol uses the following properties.

Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id
Type the material group identification for the section.
Angle Right
Define the angle on the right side of the web.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 138

 Member Cross Sections

Angle Left
Define the angle on the left side of the web.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in meters
Width
Type the width for the section. The width is defined in meters.
Perimeter
The outside perimeter distance for the section.
d
Type the depth for the section.
bf
Type the width for the section.
tw
Type the web thickness for the section. The thickness is defined in meters.
tf
Type the flange thickness for the section. The thickness is defined in meters.
kdesign
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on the welded section.
kdetail
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on welded section.
CentroidX
Type the horizontal distance from the designated member edge to the centroidal axis.
CentroidY
Type the vertical distance from the designated member edge to the centroidal axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 139

 Member Cross Sections

Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 140

 Member Cross Sections

Cross Section Symbol WedgeWF

The WedgeWF symbol uses the following properties.

Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id
Type the material group identification for the section.
Angle Right
Define the angle on the right side of the web.
Angle Left
Define the angle on the left side of the web.
Flange Right Width
Define the flange width on the right side.
Flange Left Width
Define the flange width on the left side.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).

Intergraph Smart® 3D 2D Symbols Reference Data Guide 141

 Member Cross Sections

Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in meters
Width
Type the width for the section. The width is defined in meters.
Perimeter
The outside perimeter distance for the section.
d
Type the depth for the section.
bf
Type the width for the section.
tw
Type the web thickness for the section. The thickness is defined in meters.
tf
Type the flange thickness for the section. The thickness is defined in meters.
kdesign
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on the welded section.
kdetail
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on welded section.
CentroidX
Type the horizontal distance from the designated member edge to the centroidal axis.
CentroidY
Type the vertical distance from the designated member edge to the centroidal axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 142

 Member Cross Sections

Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 143

SECTION 9

Wall Cross Sections

Wall cross-section symbols are used in the Structure task’s Wall commands. These wall cross
sections are delivered with the steel sections and follow most of the same rules.
All section tables delivered with the software use a specific set of cross-section symbols. Some
section tables use all the cross-section symbols in the set; some tables only use a subset of the
cross-section symbols. Each cross-section symbol has its own set of properties. When looking
at a section table workbook, you can determine the cross-section symbol that is being
referenced by that particular sheet by looking at the SymbolDefinition entry at the top of the
sheet.
The wall cross-section symbols are delivered with the reference data software in the [Reference
Data Folder]\SharedContent\CrossSections folder. You can create your own custom cross-
section symbols using the 2D Symbols utility that is delivered with the software.
For more information, see Cross-Section Symbol Representations in the 2D Symbols User's
Guide.

In This Section
Cross Section Symbol HW ............................................................ 145
Cross Section Symbol HWWF....................................................... 147
Cross Section Symbol Rect ........................................................... 149
Cross Section Symbol RectC ........................................................ 151
Cross Section Symbol RectCWF................................................... 154
Cross Section Symbol RectWF ..................................................... 156
Cross Section Symbol Wedge ....................................................... 158
Cross Section Symbol WedgeWF ................................................. 161

Intergraph Smart® 3D 2D Symbols Reference Data Guide 144

 Wall Cross Sections

Cross Section Symbol HW

The HW symbol uses the following properties.

Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id
Type the material group identification for the section.
Angle
Define the angle.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in meters
Width
Type the width for the section. The width is defined in meters.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 145

 Wall Cross Sections

Perimeter
The outside perimeter distance for the section.
d
Type the depth for the section.
bf
Type the width for the section.
tw
Type the web thickness for the section. The thickness is defined in meters.
tf
Type the flange thickness for the section. The thickness is defined in meters.
kdesign
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on the welded section.
kdetail
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on welded section.
CentroidY
Type the vertical distance from designated member edge to the centroidal axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 146

 Wall Cross Sections

J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.

Cross Section Symbol HWWF

The HWWF symbol uses the following properties.

Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id
Type the material group identification for the section.
Angle
Define the angle.
Flange Right Width
Define the flange width on the right side.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 147

 Wall Cross Sections

Flange Left Width

Define the flange width on the left side.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in meters
Width
Type the width for the section. The width is defined in meters.
Perimeter
The outside perimeter distance for the section.
d
Type the depth for the section.
bf
Type the width for the section.
tw
Type the web thickness for the section. The thickness is defined in meters.
tf
Type the flange thickness for the section. The thickness is defined in meters.
kdesign
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on the welded section.
kdetail
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on welded section.
CentroidX
Type the horizontal distance from the designated member edge to the centroidal axis.
CentroidY
Type the vertical distance from the designated member edge to the centroidal axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 148

 Wall Cross Sections

Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.

Cross Section Symbol Rect

The Rect symbol uses the following properties.

Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
Type the short name for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 149

 Wall Cross Sections

EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id
Type the material group identification for the section.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in meters
Width
Type the width for the section. The width is defined in meters.
Perimeter
The outside perimeter distance for the section.
bf
Type the width for the section.
tw
Type the web thickness for the section. The thickness is defined in meters.
tf
Type the flange thickness for the section. The thickness is defined in meters.
kdesign
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on the welded section.
kdetail
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on welded section.
CentroidX
Type the horizontal distance from the designated member edge to the centroidal axis.
CentroidY
Type the vertical distance from the designated member edge to the centroidal axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 150

 Wall Cross Sections

Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.

Cross Section Symbol RectC

The RectC symbol uses the following properties.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 151

 Wall Cross Sections

Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id
Type the material group identification for the section.
Angle
Define the angle.
Setback
Define the setback. This value is defined in meters.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in meters
Width
Type the width for the section. The width is defined in meters.
Perimeter
The outside perimeter distance for the section.
bf
Type the width for the section.
tw
Type the web thickness for the section. The thickness is defined in meters.
tf
Type the flange thickness for the section. The thickness is defined in meters.
kdesign
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on the welded section.
kdetail
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on welded section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 152

 Wall Cross Sections

CentroidX
Type the horizontal distance from the designated member edge to the centroidal axis.
CentroidY
Type the vertical distance from the designated member edge to the centroidal axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 153

 Wall Cross Sections

Cross Section Symbol RectCWF

The RectCWF symbol uses the following properties.

Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id
Type the material group identification for the section.
Angle
Define the angle.
Setback
Define the setback. This value is defined in meters.
Flange Right Width
Define the flange width on the right side. This valve is defined in meters.
Flange Left Width
Define the flange width on the left side. This valve is defined in meters.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 154

 Wall Cross Sections

Depth
Type the depth for the section. The depth is defined in meters
Width
Type the width for the section. The width is defined in meters.
Perimeter
The outside perimeter distance for the section.
bf
Type the width for the section.
tw
Type the web thickness for the section. The thickness is defined in meters.
tf
Type the flange thickness for the section. The thickness is defined in meters.
kdesign
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on the welded section.
kdetail
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on welded section.
CentroidX
Type the horizontal distance from the designated member edge to the centroidal axis.
CentroidY
Type the vertical distance from the designated member edge to the centroidal axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 155

 Wall Cross Sections

Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.

Cross Section Symbol RectWF

The RectWF symbol uses the following properties.

Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id
Type the material group identification for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 156

 Wall Cross Sections

Flange Right Width

Define the flange width on the right side. This valve is defined in meters.
Flange Left Width
Define the flange width on the left side. This valve is defined in meters.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in meters
Width
Type the width for the section. The width is defined in meters.
Perimeter
The outside perimeter distance for the section.
d
Type the depth for the section.
bf
Type the width for the section.
tw
Type the web thickness for the section. The thickness is defined in meters.
tf
Type the flange thickness for the section. The thickness is defined in meters.
kdesign
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on the welded section.
kdetail
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on welded section.
CentroidY
Type the vertical distance from designated member edge to the centroidal axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 157

 Wall Cross Sections

Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 158

 Wall Cross Sections

Cross Section Symbol Wedge

The Wedge symbol uses the following properties.

Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id
Type the material group identification for the section.
Angle Right
Define the angle on the right side of the web.
Angle Left
Define the angle on the left side of the web.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in meters
Width
Type the width for the section. The width is defined in meters.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 159

 Wall Cross Sections

Perimeter
The outside perimeter distance for the section.
d
Type the depth for the section.
bf
Type the width for the section.
tw
Type the web thickness for the section. The thickness is defined in meters.
tf
Type the flange thickness for the section. The thickness is defined in meters.
kdesign
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on the welded section.
kdetail
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on welded section.
CentroidX
Type the horizontal distance from the designated member edge to the centroidal axis.
CentroidY
Type the vertical distance from the designated member edge to the centroidal axis.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 160

 Wall Cross Sections

Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.

Cross Section Symbol WedgeWF

The WedgeWF symbol uses the following properties.

Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id
Type the material group identification for the section.
Angle Right

Intergraph Smart® 3D 2D Symbols Reference Data Guide 161

 Wall Cross Sections

Define the angle on the right side of the web.

Angle Left
Define the angle on the left side of the web.
Flange Right Width
Define the flange width on the right side.
Flange Left Width
Define the flange width on the left side.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in meters
Width
Type the width for the section. The width is defined in meters.
Perimeter
The outside perimeter distance for the section.
d
Type the depth for the section.
bf
Type the width for the section.
tw
Type the web thickness for the section. The thickness is defined in meters.
tf
Type the flange thickness for the section. The thickness is defined in meters.
kdesign
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on the welded section.
kdetail
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on welded section.
CentroidX
Type the horizontal distance from the designated member edge to the centroidal axis.
CentroidY
Type the vertical distance from the designated member edge to the centroidal axis.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 162

 Wall Cross Sections

Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Iyy
Type the moment of inertia for the section's local y-axis.
Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
Type the polar radius of gyration about the shear center.
H
Type the flexural constant for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 163

SECTION 10

Profile Cross Sections

Profile cross-section symbols are used in the Molded Forms and Structural Detailing tasks.
The profile cross section symbols are delivered with the software in the [Reference Data
Folder]\SharedContent\Profile Xsections folder. You can create your own custom symbols using
the 2D Symbols utility that is delivered with the software.

In This Section
Cross Section Symbol B ................................................................ 164
Cross Section Symbol BUL2 ......................................................... 166
Cross Section Symbol BUL3 ......................................................... 168
Cross Section Symbol BUT ........................................................... 171
Cross Section Symbol C_SS ......................................................... 172
Cross Section Symbol C_SType ................................................... 174
Cross Section Symbol EA ............................................................. 176
Cross Section Symbol FB .............................................................. 178
Cross Section Symbol HalfR ......................................................... 180
Cross Section Symbol I ................................................................. 183
Cross Section Symbol I_SType ..................................................... 185
Cross Section Symbol P ................................................................ 187
Cross Section Symbol R ................................................................ 189
Cross Section Symbol SB ............................................................. 191
Cross Section Symbol SqTu .......................................................... 193
Cross Section Symbol T ................................................................ 194
Cross Section Symbol T_SType .................................................... 194
Cross Section Symbol UA ............................................................. 196

Intergraph Smart® 3D 2D Symbols Reference Data Guide 164

 Profile Cross Sections

Cross Section Symbol B

The B bulb angle profile cross section symbol (B.sym) uses the following symbol parameters.

Each symbol parameter is defined and given a default value in the symbol file. Each occurrence
of a symbol bulkloaded into the catalog can be assigned different parameter values.

1 TCR - Top corner radius

2 FL - Flange length

3 Slope - Slope of the bottom of the bulb flange.

4 WL - Web length

5 CR - Corner radius

6 FR - Fillet radius of the bulb flange

7 WT - Web thickness

IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is False.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is False.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 165

 Profile Cross Sections

Cross Section Symbol BUL2

The BUL2 profile cross section symbol uses the following properties.

Section Name
Type the section name. This name appears when you label members. The section name
must be unique across the catalog.
Short Name
Type the short name for the section.
Alternate EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Description
Type a short description if needed.
Area
Type the cross-section area for the section. The area is defined in square inches or square
millimeters.
Depth
Type the depth for the section (Web Length). The depth is defined in inches or millimeters.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 166

 Profile Cross Sections

Width
Type the breadth for the section. The breadth is defined in inches or millimeters.
Perimeter
The outside perimeter distance for the section.
CentroidX
Type the location of the centroid along the local x-axis. The location is defined in inches or
millimeters.
CentroidY
Type the location of the centroid along the local y-axis. The location is defined in inches or
millimeters.
Moment of Inertia about X (Ixx)
Type the moment of inertia for the section's local x- axis.
Moment of Inertia about Y (Iyy)
Type the moment of inertia for the section's local y- axis.
Warping Statical Moment (Sw)
Type the warping statical moment for the section.
Elastic Section Modulus about X (Sxx)
Type the section modulus for the section's local x-axis.
Elastic Section Modulus about Y (Syy)
Type the section modulus for the section's local y-axis.
Torsional Moment of Inertia (J)
Type the torsional moment of inertia for the section.
Warping Constant (Cw)
Type the warping constant for the section.
Flexural Constant (H)
Type the flexural constant for the section.
Polar Radius of Gyration about Shear Center (ro)
Type the polar radius of gyration about the shear center.
Radius of Gyration about X axis (Rxx)
Type the radius of gyration for the section's local x-axis.
Radius of Gyration about Y axis (Ryy)
Type the radius of gyration for the section's local y-axis.
Radius of Gyration about Principle XY (Rxy)
Type the radius of gyration about the local z-axis. The radius is defined in inches or
millimeters.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 167

 Profile Cross Sections

Plastic Section Modulus about X (Zxx)

Type the plastic section modulus for the section's local x-axis.
Plastic Section Modulus about Y (Zyy)
Type the plastic section modulus for the section's local y-axis.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is False.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section,
whether or not the cross-section is symmetric depends on the Flange Offset (FO) value.

Cross Section Symbol BUL3

The BUL3 profile cross section symbol uses the following properties.

Section Name
Type the section name. This name appears when you label members. The section name
must be unique across the catalog.
Short Name
Type the short name for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 168

 Profile Cross Sections

Alternate EDI Name

Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Description
Type a short description if needed.
Area
Type the cross-section area for the section. The area is defined in square inches or square
millimeters.
Depth
Type the depth for the section (Web Length). The depth is defined in inches or millimeters.
Width
Type the breadth for the section. The breadth is defined in inches or millimeters.
Perimeter
The outside perimeter distance for the section.
CentroidX
Type the location of the centroid along the local x-axis. The location is defined in inches or
millimeters.
CentroidY
Type the location of the centroid along the local y-axis. The location is defined in inches or
millimeters.
Moment of Inertia about X (Ixx)
Type the moment of inertia for the section's local x- axis.
Moment of Inertia about Y (Iyy)
Type the moment of inertia for the section's local y- axis.
Warping Statical Moment (Sw)
Type the warping statical moment for the section.
Elastic Section Modulus about X (Sxx)
Type the section modulus for the section's local x-axis.
Elastic Section Modulus about Y (Syy)
Type the section modulus for the section's local y-axis.
Torsional Moment of Inertia (J)
Type the torsional moment of inertia for the section.
Warping Constant (Cw)
Type the warping constant for the section.
Flexural Constant (H)
Type the flexural constant for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 169

 Profile Cross Sections

Polar Radius of Gyration about Shear Center (ro)

Type the polar radius of gyration about the shear center.
Radius of Gyration about X axis (Rxx)
Type the radius of gyration for the section's local x-axis.
Radius of Gyration about Y axis (Ryy)
Type the radius of gyration for the section's local y-axis.
Radius of Gyration about Principle XY (Rxy)
Type the radius of gyration about the local z-axis. The radius is defined in inches or
millimeters.
Plastic Section Modulus about X (Zxx)
Type the plastic section modulus for the section's local x-axis.
Plastic Section Modulus about Y (Zyy)
Type the plastic section modulus for the section's local y-axis.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section,
whether or not the cross-section is symmetric about the x-axis depends on the Flange Offset
(FO) value.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is False.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 170

 Profile Cross Sections

Cross Section Symbol BUT

See Also
Member Cross Sections (on page 54)

Intergraph Smart® 3D 2D Symbols Reference Data Guide 171

 Profile Cross Sections

Cross Section Symbol C_SS

The C_SS profile cross section symbol uses the following properties.

Section Name
Type the section name. This name appears when you label members. The section name
must be unique across the catalog.
Short Name
Type the short name for the section.
Alternate EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Description
Type a short description if needed.
Area
Type the cross-section area for the section. The area is defined in square inches or square
millimeters.
Depth
Type the depth for the section (Web Length). The depth is defined in inches or millimeters.
Width
Type the breadth for the section. The breadth is defined in inches or millimeters.
Perimeter
The outside perimeter distance for the section.
CentroidX
Type the location of the centroid along the local x-axis. The location is defined in inches or
millimeters.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 172

 Profile Cross Sections

CentroidY
Type the location of the centroid along the local y-axis. The location is defined in inches or
millimeters.
Moment of Inertia about X (Ixx)
Type the moment of inertia for the section's local x- axis.
Moment of Inertia about Y (Iyy)
Type the moment of inertia for the section's local y- axis.
Warping Statical Moment (Sw)
Type the warping statical moment for the section.
Elastic Section Modulus about X (Sxx)
Type the section modulus for the section's local x-axis.
Elastic Section Modulus about Y (Syy)
Type the section modulus for the section's local y-axis.
Torsional Moment of Inertia (J)
Type the torsional moment of inertia for the section.
Warping Constant (Cw)
Type the warping constant for the section.
Flexural Constant (H)
Type the flexural constant for the section.
Polar Radius of Gyration about Shear Center (ro)
Type the polar radius of gyration about the shear center.
Radius of Gyration about X axis (Rxx)
Type the radius of gyration for the section's local x-axis.
Radius of Gyration about Y axis (Ryy)
Type the radius of gyration for the section's local y-axis.
Radius of Gyration about Principle XY (Rxy)
Type the radius of gyration about the local z-axis. The radius is defined in inches or
millimeters.
Plastic Section Modulus about X (Zxx)
Type the plastic section modulus for the section's local x-axis.
Plastic Section Modulus about Y (Zyy)
Type the plastic section modulus for the section's local y-axis.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 173

 Profile Cross Sections

IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is True.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is False.

Cross Section Symbol C_SType

The C_SType profile cross section symbol uses the following properties.

Section Name
Type the section name. This name appears when you label members. The section name
must be unique across the catalog.
Short Name
Type the short name for the section.
Alternate EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Description
Type a short description if needed.
Area
Type the cross-section area for the section. The area is defined in square inches or square
millimeters.
Depth
Type the depth for the section (Web Length). The depth is defined in inches or millimeters.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 174

 Profile Cross Sections

Width
Type the breadth for the section. The breadth is defined in inches or millimeters.
Perimeter
The outside perimeter distance for the section.
CentroidX
Type the location of the centroid along the local x-axis. The location is defined in inches or
millimeters.
CentroidY
Type the location of the centroid along the local y-axis. The location is defined in inches or
millimeters.
Moment of Inertia about X (Ixx)
Type the moment of inertia for the section's local x- axis.
Moment of Inertia about Y (Iyy)
Type the moment of inertia for the section's local y- axis.
Warping Statical Moment (Sw)
Type the warping statical moment for the section.
Elastic Section Modulus about X (Sxx)
Type the section modulus for the section's local x-axis.
Elastic Section Modulus about Y (Syy)
Type the section modulus for the section's local y-axis.
Torsional Moment of Inertia (J)
Type the torsional moment of inertia for the section.
Warping Constant (Cw)
Type the warping constant for the section.
Flexural Constant (H)
Type the flexural constant for the section.
Polar Radius of Gyration about Shear Center (ro)
Type the polar radius of gyration about the shear center.
Radius of Gyration about X axis (Rxx)
Type the radius of gyration for the section's local x-axis.
Radius of Gyration about Y axis (Ryy)
Type the radius of gyration for the section's local y-axis.
Radius of Gyration about Principle XY (Rxy)
Type the radius of gyration about the local z-axis. The radius is defined in inches or
millimeters.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 175

 Profile Cross Sections

Plastic Section Modulus about X (Zxx)

Type the plastic section modulus for the section's local x-axis.
Plastic Section Modulus about Y (Zyy)
Type the plastic section modulus for the section's local y-axis.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is True.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is False.

Cross Section Symbol EA

The EA profile cross section symbol uses the following properties.

Section Name
Type the section name. This name appears when you label members. The section name
must be unique across the catalog.
Short Name
Type the short name for the section.
Alternate EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 176

 Profile Cross Sections

Description
Type a short description if needed.
Area
Type the cross-section area for the section. The area is defined in square inches or square
millimeters.
Depth
Type the depth for the section (Web Length). The depth is defined in inches or millimeters.
Width
Type the breadth for the section. The breadth is defined in inches or millimeters.
Perimeter
The outside perimeter distance for the section.
CentroidX
Type the location of the centroid along the local x-axis. The location is defined in inches or
millimeters.
CentroidY
Type the location of the centroid along the local y-axis. The location is defined in inches or
millimeters.
Moment of Inertia about X (Ixx)
Type the moment of inertia for the section's local x- axis.
Moment of Inertia about Y (Iyy)
Type the moment of inertia for the section's local y- axis.
Warping Statical Moment (Sw)
Type the warping statical moment for the section.
Elastic Section Modulus about X (Sxx)
Type the section modulus for the section's local x-axis.
Elastic Section Modulus about Y (Syy)
Type the section modulus for the section's local y-axis.
Torsional Moment of Inertia (J)
Type the torsional moment of inertia for the section.
Warping Constant (Cw)
Type the warping constant for the section.
Flexural Constant (H)
Type the flexural constant for the section.
Polar Radius of Gyration about Shear Center (ro)
Type the polar radius of gyration about the shear center.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 177

 Profile Cross Sections

Radius of Gyration about X axis (Rxx)

Type the radius of gyration for the section's local x-axis.
Radius of Gyration about Y axis (Ryy)
Type the radius of gyration for the section's local y-axis.
Radius of Gyration about Principle XY (Rxy)
Type the radius of gyration about the local z-axis. The radius is defined in inches or
millimeters.
Plastic Section Modulus about X (Zxx)
Type the plastic section modulus for the section's local x-axis.
Plastic Section Modulus about Y (Zyy)
Type the plastic section modulus for the section's local y-axis.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is False.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is False.

Cross Section Symbol FB

The FB profile cross section symbol uses the following properties.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 178

 Profile Cross Sections

Section Name
Type the section name. This name appears when you label members. The section name
must be unique across the catalog.
Short Name
Type the short name for the section.
Alternate EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Description
Type a short description if needed.
Area
Type the cross-section area for the section. The area is defined in square inches or square
millimeters.
Depth
Type the depth for the section (Web Length). The depth is defined in inches or millimeters.
Width
Type the breadth for the section. The breadth is defined in inches or millimeters.
Perimeter
The outside perimeter distance for the section.
CentroidX
Type the location of the centroid along the local x-axis. The location is defined in inches or
millimeters.
CentroidY
Type the location of the centroid along the local y-axis. The location is defined in inches or
millimeters.
Moment of Inertia about X (Ixx)
Type the moment of inertia for the section's local x- axis.
Moment of Inertia about Y (Iyy)
Type the moment of inertia for the section's local y- axis.
Warping Statical Moment (Sw)
Type the warping statical moment for the section.
Elastic Section Modulus about X (Sxx)
Type the section modulus for the section's local x-axis.
Elastic Section Modulus about Y (Syy)
Type the section modulus for the section's local y-axis.
Torsional Moment of Inertia (J)

Intergraph Smart® 3D 2D Symbols Reference Data Guide 179

 Profile Cross Sections

Type the torsional moment of inertia for the section.

Warping Constant (Cw)
Type the warping constant for the section.
Flexural Constant (H)
Type the flexural constant for the section.
Polar Radius of Gyration about Shear Center (ro)
Type the polar radius of gyration about the shear center.
Radius of Gyration about X axis (Rxx)
Type the radius of gyration for the section's local x-axis.
Radius of Gyration about Y axis (Ryy)
Type the radius of gyration for the section's local y-axis.
Radius of Gyration about Principle XY (Rxy)
Type the radius of gyration about the local z-axis. The radius is defined in inches or
millimeters.
Plastic Section Modulus about X (Zxx)
Type the plastic section modulus for the section's local x-axis.
Plastic Section Modulus about Y (Zyy)
Type the plastic section modulus for the section's local y-axis.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is True.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is True.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 180

 Profile Cross Sections

Cross Section Symbol HalfR

The HalfR profile cross section symbol uses the following properties.

Section Name
Type the section name. This name appears when you label members. The section name
must be unique across the catalog.
Short Name
Type the short name for the section.
Alternate EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Description
Type a short description if needed.
Area
Type the cross-section area for the section. The area is defined in square inches or square
millimeters.
Depth
Type the depth for the section (Web Length). The depth is defined in inches or millimeters.
Width
Type the breadth for the section. The breadth is defined in inches or millimeters.
Perimeter
The outside perimeter distance for the section.
CentroidX
Type the location of the centroid along the local x-axis. The location is defined in inches or
millimeters.
CentroidY
Type the location of the centroid along the local y-axis. The location is defined in inches or
millimeters.
Moment of Inertia about X (Ixx)
Type the moment of inertia for the section's local x- axis.
Moment of Inertia about Y (Iyy)
Type the moment of inertia for the section's local y- axis.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 181

 Profile Cross Sections

Warping Statical Moment (Sw)

Type the warping statical moment for the section.
Elastic Section Modulus about X (Sxx)
Type the section modulus for the section's local x-axis.
Elastic Section Modulus about Y (Syy)
Type the section modulus for the section's local y-axis.
Torsional Moment of Inertia (J)
Type the torsional moment of inertia for the section.
Warping Constant (Cw)
Type the warping constant for the section.
Flexural Constant (H)
Type the flexural constant for the section.
Polar Radius of Gyration about Shear Center (ro)
Type the polar radius of gyration about the shear center.
Radius of Gyration about X axis (Rxx)
Type the radius of gyration for the section's local x-axis.
Radius of Gyration about Y axis (Ryy)
Type the radius of gyration for the section's local y-axis.
Radius of Gyration about Principle XY (Rxy)
Type the radius of gyration about the local z-axis. The radius is defined in inches or
millimeters.
Plastic Section Modulus about X (Zxx)
Type the plastic section modulus for the section's local x-axis.
Plastic Section Modulus about Y (Zyy)
Type the plastic section modulus for the section's local y-axis.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is False.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is True.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 182

 Profile Cross Sections

Cross Section Symbol I

The I profile cross section symbol uses the following properties.

Section Name
Type the section name. This name appears when you label members. The section name
must be unique across the catalog.
Short Name
Type the short name for the section.
Alternate EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Description
Type a short description if needed.
Area
Type the cross-section area for the section. The area is defined in square inches or square
millimeters.
Depth
Type the depth for the section (Web Length). The depth is defined in inches or millimeters.
Width
Type the breadth for the section. The breadth is defined in inches or millimeters.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 183

 Profile Cross Sections

Perimeter
The outside perimeter distance for the section.
CentroidX
Type the location of the centroid along the local x-axis. The location is defined in inches or
millimeters.
CentroidY
Type the location of the centroid along the local y-axis. The location is defined in inches or
millimeters.
Moment of Inertia about X (Ixx)
Type the moment of inertia for the section's local x- axis.
Moment of Inertia about Y (Iyy)
Type the moment of inertia for the section's local y- axis.
Warping Statical Moment (Sw)
Type the warping statical moment for the section.
Elastic Section Modulus about X (Sxx)
Type the section modulus for the section's local x-axis.
Elastic Section Modulus about Y (Syy)
Type the section modulus for the section's local y-axis.
Torsional Moment of Inertia (J)
Type the torsional moment of inertia for the section.
Warping Constant (Cw)
Type the warping constant for the section.
Flexural Constant (H)
Type the flexural constant for the section.
Polar Radius of Gyration about Shear Center (ro)
Type the polar radius of gyration about the shear center.
Radius of Gyration about X axis (Rxx)
Type the radius of gyration for the section's local x-axis.
Radius of Gyration about Y axis (Ryy)
Type the radius of gyration for the section's local y-axis.
Radius of Gyration about Principle XY (Rxy)
Type the radius of gyration about the local z-axis. The radius is defined in inches or
millimeters.
Plastic Section Modulus about X (Zxx)
Type the plastic section modulus for the section's local x-axis.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 184

 Profile Cross Sections

Plastic Section Modulus about Y (Zyy)

Type the plastic section modulus for the section's local y-axis.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is True.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is True.

Cross Section Symbol I_SType

The I_SType profile cross section symbol uses the following properties.

Section Name
Type the section name. This name appears when you label members. The section name
must be unique across the catalog.
Short Name
Type the short name for the section.
Alternate EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 185

 Profile Cross Sections

Description
Type a short description if needed.
Area
Type the cross-section area for the section. The area is defined in square inches or square
millimeters.
Depth
Type the depth for the section (Web Length). The depth is defined in inches or millimeters.
Width
Type the breadth for the section. The breadth is defined in inches or millimeters.
Perimeter
The outside perimeter distance for the section.
CentroidX
Type the location of the centroid along the local x-axis. The location is defined in inches or
millimeters.
CentroidY
Type the location of the centroid along the local y-axis. The location is defined in inches or
millimeters.
Moment of Inertia about X (Ixx)
Type the moment of inertia for the section's local x- axis.
Moment of Inertia about Y (Iyy)
Type the moment of inertia for the section's local y- axis.
Warping Statical Moment (Sw)
Type the warping statical moment for the section.
Elastic Section Modulus about X (Sxx)
Type the section modulus for the section's local x-axis.
Elastic Section Modulus about Y (Syy)
Type the section modulus for the section's local y-axis.
Torsional Moment of Inertia (J)
Type the torsional moment of inertia for the section.
Warping Constant (Cw)
Type the warping constant for the section.
Flexural Constant (H)
Type the flexural constant for the section.
Polar Radius of Gyration about Shear Center (ro)
Type the polar radius of gyration about the shear center.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 186

 Profile Cross Sections

Radius of Gyration about X axis (Rxx)

Type the radius of gyration for the section's local x-axis.
Radius of Gyration about Y axis (Ryy)
Type the radius of gyration for the section's local y-axis.
Radius of Gyration about Principle XY (Rxy)
Type the radius of gyration about the local z-axis. The radius is defined in inches or
millimeters.
Plastic Section Modulus about X (Zxx)
Type the plastic section modulus for the section's local x-axis.
Plastic Section Modulus about Y (Zyy)
Type the plastic section modulus for the section's local y-axis.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is True.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is True.

Cross Section Symbol P

The P profile cross section symbol uses the following properties.

Section Name
Type the section name. This name appears when you label members. The section name
must be unique across the catalog.
Short Name
Type the short name for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 187

 Profile Cross Sections

Alternate EDI Name

Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Description
Type a short description if needed.
Area
Type the cross-section area for the section. The area is defined in square inches or square
millimeters.
Depth
Type the depth for the section (Web Length). The depth is defined in inches or millimeters.
Width
Type the breadth for the section. The breadth is defined in inches or millimeters.
Perimeter
The outside perimeter distance for the section.
CentroidX
Type the location of the centroid along the local x-axis. The location is defined in inches or
millimeters.
CentroidY
Type the location of the centroid along the local y-axis. The location is defined in inches or
millimeters.
Moment of Inertia about X (Ixx)
Type the moment of inertia for the section's local x- axis.
Moment of Inertia about Y (Iyy)
Type the moment of inertia for the section's local y- axis.
Warping Statical Moment (Sw)
Type the warping statical moment for the section.
Elastic Section Modulus about X (Sxx)
Type the section modulus for the section's local x-axis.
Elastic Section Modulus about Y (Syy)
Type the section modulus for the section's local y-axis.
Torsional Moment of Inertia (J)
Type the torsional moment of inertia for the section.
Warping Constant (Cw)
Type the warping constant for the section.
Flexural Constant (H)
Type the flexural constant for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 188

 Profile Cross Sections

Polar Radius of Gyration about Shear Center (ro)

Type the polar radius of gyration about the shear center.
Radius of Gyration about X axis (Rxx)
Type the radius of gyration for the section's local x-axis.
Radius of Gyration about Y axis (Ryy)
Type the radius of gyration for the section's local y-axis.
Radius of Gyration about Principle XY (Rxy)
Type the radius of gyration about the local z-axis. The radius is defined in inches or
millimeters.
Plastic Section Modulus about X (Zxx)
Type the plastic section modulus for the section's local x-axis.
Plastic Section Modulus about Y (Zyy)
Type the plastic section modulus for the section's local y-axis.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is True.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is True.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is True.

Cross Section Symbol R

The R profile cross section symbol uses the following properties.

Section Name
Type the section name. This name appears when you label members. The section name
must be unique across the catalog.
Short Name
Type the short name for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 189

 Profile Cross Sections

Alternate EDI Name

Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Description
Type a short description if needed.
Area
Type the cross-section area for the section. The area is defined in square inches or square
millimeters.
Depth
Type the depth for the section (Web Length). The depth is defined in inches or millimeters.
Width
Type the breadth for the section. The breadth is defined in inches or millimeters.
Perimeter
The outside perimeter distance for the section.
CentroidX
Type the location of the centroid along the local x-axis. The location is defined in inches or
millimeters.
CentroidY
Type the location of the centroid along the local y-axis. The location is defined in inches or
millimeters.
Moment of Inertia about X (Ixx)
Type the moment of inertia for the section's local x- axis.
Moment of Inertia about Y (Iyy)
Type the moment of inertia for the section's local y- axis.
Warping Statical Moment (Sw)
Type the warping statical moment for the section.
Elastic Section Modulus about X (Sxx)
Type the section modulus for the section's local x-axis.
Elastic Section Modulus about Y (Syy)
Type the section modulus for the section's local y-axis.
Torsional Moment of Inertia (J)
Type the torsional moment of inertia for the section.
Warping Constant (Cw)
Type the warping constant for the section.
Flexural Constant (H)
Type the flexural constant for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 190

 Profile Cross Sections

Polar Radius of Gyration about Shear Center (ro)

Type the polar radius of gyration about the shear center.
Radius of Gyration about X axis (Rxx)
Type the radius of gyration for the section's local x-axis.
Radius of Gyration about Y axis (Ryy)
Type the radius of gyration for the section's local y-axis.
Radius of Gyration about Principle XY (Rxy)
Type the radius of gyration about the local z-axis. The radius is defined in inches or
millimeters.
Plastic Section Modulus about X (Zxx)
Type the plastic section modulus for the section's local x-axis.
Plastic Section Modulus about Y (Zyy)
Type the plastic section modulus for the section's local y-axis.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is True.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is True.

Cross Section Symbol SB

The SB profile cross section symbol uses the following properties.

Name
Type the section name. This name appears when you label members. The section name
must be unique across the catalog.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 191

 Profile Cross Sections

Short Name
Type the short name for the section.
Alternate EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Description
Type a short description if needed.
Area
Type the cross-section area for the section. The area is defined in square inches or square
millimeters.
Depth
Type the depth for the section (Web Length). The depth is defined in inches or millimeters.
Width
Type the breadth for the section. The breadth is defined in inches or millimeters.
Perimeter
The outside perimeter distance for the section.
CentroidX
Type the location of the centroid along the local x-axis. The location is defined in inches or
millimeters.
CentroidY
Type the location of the centroid along the local y-axis. The location is defined in inches or
millimeters.
Moment of Inertia about X (Ixx)
Type the moment of inertia for the section's local x- axis.
Moment of Inertia about Y (Iyy)
Type the moment of inertia for the section's local y- axis.
Warping Statical Moment (Sw)
Type the warping statical moment for the section.
Elastic Section Modulus about X (Sxx)
Type the section modulus for the section's local x-axis.
Elastic Section Modulus about Y (Syy)
Type the section modulus for the section's local y-axis.
Torsional Moment of Inertia (J)
Type the torsional moment of inertia for the section.
Warping Constant (Cw)
Type the warping constant for the section.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 192

 Profile Cross Sections

Flexural Constant (H)

Type the flexural constant for the section.
Polar Radius of Gyration about Shear Center (ro)
Type the polar radius of gyration about the shear center.
Radius of Gyration about X axis (Rxx)
Type the radius of gyration for the section's local x-axis.
Radius of Gyration about Y axis (Ryy)
Type the radius of gyration for the section's local y-axis.
Radius of Gyration about Principle XY (Rxy)
Type the radius of gyration about the local z-axis. The radius is defined in inches or
millimeters.
Plastic Section Modulus about X (Zxx)
Type the plastic section modulus for the section's local x-axis.
Plastic Section Modulus about Y (Zyy)
Type the plastic section modulus for the section's local y-axis.

Cross Section Symbol SqTu

See Also
Member Cross Sections (on page 54)

Intergraph Smart® 3D 2D Symbols Reference Data Guide 193

 Profile Cross Sections

Cross Section Symbol T

See Also
Member Cross Sections (on page 54)

Cross Section Symbol T_SType

The T_SType profile cross section symbol uses the following properties.

Section Name
Type the section name. This name appears when you label members. The section name
must be unique across the catalog.
Short Name
Type the short name for the section.
Alternate EDI Name
Type the Electronic Data Interchange name for the section. This name is used when

Intergraph Smart® 3D 2D Symbols Reference Data Guide 194

 Profile Cross Sections

translating sections through CIMsteel. This property is currently not used.

Description
Type a short description if needed.
Area
Type the cross-section area for the section. The area is defined in square inches or square
millimeters.
Depth
Type the depth for the section (Web Length). The depth is defined in inches or millimeters.
Width
Type the breadth for the section. The breadth is defined in inches or millimeters.
Perimeter
The outside perimeter distance for the section.
CentroidX
Type the location of the centroid along the local x-axis. The location is defined in inches or
millimeters.
CentroidY
Type the location of the centroid along the local y-axis. The location is defined in inches or
millimeters.
Moment of Inertia about X (Ixx)
Type the moment of inertia for the section's local x- axis.
Moment of Inertia about Y (Iyy)
Type the moment of inertia for the section's local y- axis.
Warping Statical Moment (Sw)
Type the warping statical moment for the section.
Elastic Section Modulus about X (Sxx)
Type the section modulus for the section's local x-axis.
Elastic Section Modulus about Y (Syy)
Type the section modulus for the section's local y-axis.
Torsional Moment of Inertia (J)
Type the torsional moment of inertia for the section.
Warping Constant (Cw)
Type the warping constant for the section.
Flexural Constant (H)
Type the flexural constant for the section.
Polar Radius of Gyration about Shear Center (ro)
Type the polar radius of gyration about the shear center.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 195

 Profile Cross Sections

Radius of Gyration about X axis (Rxx)

Type the radius of gyration for the section's local x-axis.
Radius of Gyration about Y axis (Ryy)
Type the radius of gyration for the section's local y-axis.
Radius of Gyration about Principle XY (Rxy)
Type the radius of gyration about the local z-axis. The radius is defined in inches or
millimeters.
Plastic Section Modulus about X (Zxx)
Type the plastic section modulus for the section's local x-axis.
Plastic Section Modulus about Y (Zyy)
Type the plastic section modulus for the section's local y-axis.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is False.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is True.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 196

 Profile Cross Sections

Cross Section Symbol UA

The UA profile cross section symbol uses the following properties.

Section Name
Type the section name. This name appears when you label members. The section name
must be unique across the catalog.
Short Name
Type the short name for the section.
Alternate EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Description
Type a short description if needed.
Area
Type the cross-section area for the section. The area is defined in square inches or square
millimeters.
Depth
Type the depth for the section (Web Length). The depth is defined in inches or millimeters.
Width
Type the breadth for the section. The breadth is defined in inches or millimeters.
Perimeter
The outside perimeter distance for the section.
CentroidX
Type the location of the centroid along the local x-axis. The location is defined in inches or
millimeters.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 197

 Profile Cross Sections

CentroidY
Type the location of the centroid along the local y-axis. The location is defined in inches or
millimeters.
Moment of Inertia about X (Ixx)
Type the moment of inertia for the section's local x- axis.
Moment of Inertia about Y (Iyy)
Type the moment of inertia for the section's local y- axis.
Warping Statical Moment (Sw)
Type the warping statical moment for the section.
Elastic Section Modulus about X (Sxx)
Type the section modulus for the section's local x-axis.
Elastic Section Modulus about Y (Syy)
Type the section modulus for the section's local y-axis.
Torsional Moment of Inertia (J)
Type the torsional moment of inertia for the section.
Warping Constant (Cw)
Type the warping constant for the section.
Flexural Constant (H)
Type the flexural constant for the section.
Polar Radius of Gyration about Shear Center (ro)
Type the polar radius of gyration about the shear center.
Radius of Gyration about X axis (Rxx)
Type the radius of gyration for the section's local x-axis.
Radius of Gyration about Y axis (Ryy)
Type the radius of gyration for the section's local y-axis.
Radius of Gyration about Principle XY (Rxy)
Type the radius of gyration about the local z-axis. The radius is defined in inches or
millimeters.
Plastic Section Modulus about X (Zxx)
Type the plastic section modulus for the section's local x-axis.
Plastic Section Modulus about Y (Zyy)
Type the plastic section modulus for the section's local y-axis.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 198

 Profile Cross Sections

IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is False.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is False.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 199

SECTION 11

Edge Features
Edge feature symbols are delivered in the SharedContent share in the [Reference Data
Folder]\SharedContent\FTLIBRRY\Edge Features folder and the [Reference Data
Folder]\SharedContent\MarineLibrary\Edge Features folder.

Place Edge Feature lets you select the Method and Type after you select an edge.

When Method is set to Along Edge or Offset and Type is set to Edge Feature, then Smart 3D
places CutEdge by default. You can select OffEdge items by setting the question Off of Edge
to Yes on the Properties dialog box as shown in following picture.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 200

SECTION 12

Profile End Cuts

Use web cut and flange cut symbols with profile stiffeners.
Smart 3D provides end cut symbols in the following locations:
 Web cuts are in the [Reference Data Folder]\SharedContent\FTLIBRARY\Web Cuts
and [Reference Data Folder]\SharedContent\Web Cuts folders.
 Flange cuts are in the [Reference Data Folder]\SharedContent\FTLIBRARY\Flange Cuts
and [Reference Data Folder]\SharedContent\Flange Cuts folders.
Assembly connection rules determine the end cut type. You can change the end cut type on the
Selection tab in the Assembly Connection Properties dialog box. For more information on
end cut rules, see End Cuts.

In This Section
Weld and Clip End Cuts ................................................................ 201
Snip End Cuts ................................................................................ 232
Cut Back End Cuts ........................................................................ 236
End-to-End End Cuts ..................................................................... 237
Long Box End Cuts ........................................................................ 246
Miter End Cuts ............................................................................... 247
Bounded by Plate ER .................................................................... 248
Optional Flange Cut Shapes ......................................................... 248

Weld and Clip End Cuts

Bounded with Plate or Profile Web
Bounded Section Type: EA, UA, BP
Bounding Previews
End
Object
Cut End Condition Item Name Web Flange
/Bounding
Type
Side

Plate Clip/ Any WebCut:

Weld W_Welded_StraightCut
FlangeCut:
EA, UA - F_StraightCut_FromB
BP - F_StraightCut_FromB_BP

Intergraph Smart® 3D 2D Symbols Reference Data Guide 201

 Profile End Cuts

Bounding Previews
End
Object
Cut End Condition Item Name Web Flange
/Bounding
Type
Side

Default:
WebCut:
W_Welded_Slope_Left
FlangeCut:
EA, UA - F_SlopeRight_
DirN_CutN_FromP
BP - F_SlopeRight_DirN_
CutN_FromP_BP

Optional:
WebCut:
W_Clip_Cope_NoFlange_Left
FlangeCut:
EA, UA - F_StraightCut_DirN_
CutN_FromP
Bounding height < BP - F_StraightCut_DirN_
bounded height and CutN_FromP_BP
angle between
bounding and
bounded web left > 90 Optional:
deg WebCut:
BP/UA/EA - W_SnipTopRadius
Web Left
Clip FlangeCut:
FB - Web EA, UA - F_SlopeRight_DirN_
Left CutN_FromP
F_StraightCut_DirN_CutN_
FromP_BP

Optional:
WebCut:
W_Welded_Slope_Right2
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FromP
BP - F_StraightCut_DirN_
CutN_FromP_BP

Default:

Bounding height < WebCut:

bounded height and W_Welded_Slope_Left
angle between FlangeCut:
bounding and EA, UA - F_SlopeRight_DirN_
bounded web left < 90 CutN_FromP
deg
BP - F_SlopeRight_DirN_
CutN_FromP_BP

Intergraph Smart® 3D 2D Symbols Reference Data Guide 202

 Profile End Cuts

Bounding Previews
End
Object
Cut End Condition Item Name Web Flange
/Bounding
Type
Side

Optional:
WebCut:
W_Clip_Cope_NoFlange_Left
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FromP
BP - F_SlopeRight_DirN_
CutN_FromP_BP

Optional:
WebCut:
W_SnipTopRadius
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FromP
BP - F_StraightCut_DirN_
CutN_FromP_BP

Optional:
WebCut:
W_Welded_Slope_Right2
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FromP
BP - F_StraightCut_DirN_
CutN_FromP_BP

Optional:
WebCut:
W_Clip_Cope_Left2
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FromP
BP - F_StraightCut_DirN_
CutN_FromP_BP

WebCut:
W_Welded_Slope_Left
FlangeCut:
Bounding height <
Weld EA, UA - F_SlopeRight_DirN_
bounded height
CutN_FromP
BP - F_SlopeRight_DirN_
CutN_FromP_BP

Intergraph Smart® 3D 2D Symbols Reference Data Guide 203

 Profile End Cuts

Bounding Previews
End
Object
Cut End Condition Item Name Web Flange
/Bounding
Type
Side

Optional:
WebCut:
W_SnipTopRadius
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FromP
BP - F_StraightCut_DirN_
CutN_FromP_BP

WebCut:
W_Welded_StraightCut
FlangeCut:
Clip/ Bounding height >
EA, UA - F_StraightCut_
Weld bounded height
FromB
BP - F_StraightCut_
FromB_BP

Default:
WebCut:
W_Welded_Slope_Right
FlangeCut:
EA, UA - F_SlopeRight_
DirN_CutN_FromP
BP - F_SlopeRight_DirN_
CutN_FromP_BP

Optional:
WebCut:
Bounding height < W_Clip_Cope_
bounded height and NoFlange_Right
FB - angle between
Clip FlangeCut:
WebRight bounding and
EA, UA - F_StraightCut_DirN_
bounded web left > 90
CutN_FromP
deg
BP - F_StraightCut_DirN_
CutN_FromP_BP

Optional:
WebCut:
W_SnipTopRadius
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FromP
BP - F_StraightCut_DirN_
CutN_FromP_BP

Intergraph Smart® 3D 2D Symbols Reference Data Guide 204

 Profile End Cuts

Bounding Previews
End
Object
Cut End Condition Item Name Web Flange
/Bounding
Type
Side

Optional:
WebCut:
W_Clip_Cope_Right2
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FromP
BP - F_StraightCut_DirN_
CutN_FromP_BP

Default:
WebCut:
W_Welded_Slope_Right
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FromP
BP - F_SlopeRight_DirN_
CutN_FromP_BP

Optional:
WebCut:
W_Clip_Cope_NoFlange_
Right
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FromP
Bounding height <
bounded height and BP - F_SlopeRight_DirN_
angle between CutN_FromP_BP
bounding and
bounded web left < 90 Optional:
deg
WebCut:
W_Clip_Cope_Right2
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FromP
BP - F_SlopeRight_DirN_
CutN_FromP_BP

Optional:
WebCut:
W_SnipTopRadius
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FromP
BP - F_StraightCut_DirN_
CutN_FromP_BP

Intergraph Smart® 3D 2D Symbols Reference Data Guide 205

 Profile End Cuts

Bounding Previews
End
Object
Cut End Condition Item Name Web Flange
/Bounding
Type
Side

Default:
WebCut:
W_Welded_Slope_Right
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FromP
BP - F_SlopeRight_DirN_
CutN_FromP_BP
Bounding height <
bounded height
Optional:
WebCut:
W_SnipTopRadius
Weld
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FromP
BP - F_StraightCut_DirN_
CutN_FromP_BP

WebCut:
W_Welded_StraightCut
Bounding height >
FlangeCut:
bounded height
EA, UA - F_StraightCut_FromB
BP - F_StraightCut_FromB_BP

WebCut:
W_Welded_Slope_Right
EA, UA -
FlangeCut:F_SlopeRight_
DirN_CutN_FTS_FromP
BP - F_SlopeRight_DirN_
CutN_FTS_FromP_BP

WebCut:
W_Clip_RightWithRadius
UA/EA/B_L FlangeCut:
3 Welded/ Bounding height <
EA, UA - F_SlopeRight_DirN_
Clip bounded height
- Web Right CutN_FTS_FromP
BP - F_SlopeRight_DirN_
CutN_FTS_FromP_BP

WebCut:
BP - W_SnipWithRadius
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FTS_FromP
BP - F_SlopeRight_DirN_
CutN_FTS_FromP_BP

Intergraph Smart® 3D 2D Symbols Reference Data Guide 206

 Profile End Cuts

Bounding Previews
End
Object
Cut End Condition Item Name Web Flange
/Bounding
Type
Side

WebCut:
W_Clip_Right
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FTS_FromP
BP - F_SlopeRight_DirN_
CutN_FTS_FromP_BP

WebCut:
W_WeldedHole_Right
FlangeCut:
EA, UA - F_StraightCut_DirC_
CutC_FromP_PC
BP - F_StraightCut_DirC_
CutC_FromP_BP_PC

WebCut:
W_WeldedHole_Right_1
FlangeCut:
EA, UA - F_StraightCut_DirC_
CutC_FromP_PC
BP - F_StraightCut_DirC_
CutC_FromP_BP_PC

WebCut:
Welded_TopSnipe_
Bounding height = Angle_Equal
Welded
bounded height
BP - Welded_TopSnipe_
Angle_Equal_BP
FlangeCut:
EA, UA - F_StraightCut_DirC_
CutC_FromP_PC
BP - F_StraightCut_DirC_
CutC_FromP_BP_PC

WebCut:
Welded_TopSnipe_
Angle_Equal2
BP - Welded_TopSnipe_
Angle_Equal_BP
FlangeCut:
EA, UA - F_StraightCut_DirC_
CutC_FromP_PC
BP - F_StraightCut_DirC_
CutC_FromP_BP_PC

Intergraph Smart® 3D 2D Symbols Reference Data Guide 207

 Profile End Cuts

Bounding Previews
End
Object
Cut End Condition Item Name Web Flange
/Bounding
Type
Side

WebCut:
W_Clip_Cope_Right
FlangeCut:
EA, UA - F_StraightCut_DirN_
CutN_FromP
BP - F_StraightCut_DirN_
CutN_FromP_BP

WebCut:
W_Clip_Cope_Right_2
FlangeCut:
EA, UA - F_StraightCut_DirN_
CutN_FromP
BP - F_StraightCut_DirN_
CutN_FromP_BP

Bounding height =
bounded height and WebCut:
angle between Welded_TopSnipe_
bounding and Angle_Equal
bounded web left > 90
BP - Welded_TopSnipe_
deg
Angle_Equal_BP

Clip FlangeCut:
EA, UA - F_StraightCut_DirC_
CutC_FromP_PC
BP - F_StraightCut_DirC_
CutC_FromP_BP_PC

WebCut:
Welded_TopSnipe_
Angle_Equal_2
BP - Welded_TopSnipe_
Angle_Equal_BP
FlangeCut:
EA, UA - F_StraightCut_DirC_
CutC_FromP_PC
BP - F_StraightCut_DirC_
CutC_FromP_BP_PC

WebCut:
Bounding height = W_Clip_Cope_Right
bounded height and
FlangeCut:
angle between
EA, UA - F_SlopeRight_DirN_
bounding and
CutN_FTS_FromP
bounded web left < 90
deg BP - F_SlopeRight_DirN_
CutN_FTS_FromP_BP

Intergraph Smart® 3D 2D Symbols Reference Data Guide 208

 Profile End Cuts

Bounding Previews
End
Object
Cut End Condition Item Name Web Flange
/Bounding
Type
Side

WebCut:
W_Clip_Cope_Right2
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FTS_FromP
BP - F_SlopeRight_DirN_
CutN_FTS_FromP_BP

WebCut:
Welded_TopSnipe_
Angle_Equal
BP - Welded_TopSnipe_
Angle_Equal_BP
FlangeCut:
EA, UA - F_StraightCut_DirC_
CutC_FromP_PC
BP - F_StraightCut_DirC_
CutC_FromP_BP_PC

WebCut:
Welded_TopSnipe_
Angle_Equal_2
BP - Welded_TopSnipe_
Angle_Equal_BP
FlangeCut:
EA, UA - F_StraightCut_DirC_
CutC_FromP_PC
BP - F_StraightCut_DirC_
CutC_FromP_BP_PC

WebCut:
W_Welded_Slope_Right
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FTS_FromP
BP - F_SlopeRight_DirN_
Bounding height > CutN_FTS_FromP_BP
bounded height and
Welded/
bounding height * 2/3
Clip WebCut:
+ 25 mm < bounded
height Welded_TopSnipe_
Angle_Equal2
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FTS_FromP
BP - F_SlopeRight_DirN_
CutN_FTS_FromP_BP

Intergraph Smart® 3D 2D Symbols Reference Data Guide 209

 Profile End Cuts

Bounding Previews
End
Object
Cut End Condition Item Name Web Flange
/Bounding
Type
Side

WebCut:
W_Welded_StraightCut
Bounding height * 2/3 FlangeCut:
+ 25 mm > bounded EA, UA - F_StraightCut_
height FromB
BP - F_StraightCut_
FromB_BP

WebCut:
W_Welded_Slope_Right
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FTS_FromP
BP - F_SlopeRight_DirN_
CutN_FTS_FromP_BP

WebCut:
W_Clip_RightWithRadius_BP
FlangeCut:
Welded/ Bounding height <
EA, UA - F_SlopeRight_DirN_
Clip bounded height
CutN_FTS_FromP
BP - F_SlopeRight_DirN_
CutN_FTS_FromP_BP

WebCut:
BP - W_SnipWithRadius_BP
FlangeCut:
EA, UA - F_SlopeRight_DirN_
BP - Web CutN_FTS_FromP
Right BP - F_SlopeRight_DirN_
CutN_FTS_FromP_BP

None
WebCut:
Bounding height = W_CopeBulb_Flange
Welded
bounded height
No FlangeCut

WebCut:
Bounding height = W_Clip_Cope_Right
bounded height and
FlangeCut:
angle between
EA, UA - F_StraightCut_DirN_
bounding and
CutN_FromP
bounded web left > 90
deg BP - F_StraightCut_DirN_
Clip CutN_FromP_BP

Bounding height =
bounded height and WebCut:
angle between W_Clip_Cope_Right
bounding and

Intergraph Smart® 3D 2D Symbols Reference Data Guide 210

 Profile End Cuts

Bounding Previews
End
Object
Cut End Condition Item Name Web Flange
/Bounding
Type
Side
bounded web left < 90 FlangeCut:
deg EA, UA - F_SlopeRight_DirN_
CutN_FTS_FromP
BP - F_SlopeRight_DirN_
CutN_FTS_FromP_BP

WebCut:
W_Welded_Slope_Right
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FTS_FromP
BP - F_SlopeRight_DirN_
Bounding height - CutN_FTS_FromP_BP
bounding flange
thickness < bounded
height WebCut:
W_Clip_RightWithRadius_BP
FlangeCut:
Welded/
EA, UA - F_SlopeRight_DirN_
Clip
CutN_FTS_FromP
BP - F_SlopeRight_DirN_
CutN_FTS_FromP_BP

WebCut:
W_Welded_StraightCut
FlangeCut:
Other Condition EA, UA - F_StraightCut_
FromB
BP - F_StraightCut_
FromB_BP

WebCut:
W_Welded_Slope_Left
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FTS_FromP
BP - F_SlopeRight_DirN_
CutN_FTS_FromP_BP
BUT/BUTL2 Bounding height =
Welded
- Web Left bounded height WebCut:
Welded_TopSnipe_
Angle_Equal_Left
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FTS_FromP
BP - F_SlopeRight_DirN_
CutN_FTS_FromP_BP

Intergraph Smart® 3D 2D Symbols Reference Data Guide 211

 Profile End Cuts

Bounding Previews
End
Object
Cut End Condition Item Name Web Flange
/Bounding
Type
Side

WebCut:
W_Clip_Cope_Left
FlangeCut:
EA, UA - F_StraightCut_DirN_
CutN_FromP
BP - F_StraightCut_DirN_
CutN_FromP_BP
Bounding height =
bounded height and
angle between WebCut:
bounding and Welded_TopSnipe_
bounded web left > 90 Angle_Equal_Left
deg
BP - Welded_TopSnipe_
Angle_Equal_L_BP
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FTS_FromP
BP - F_SlopeRight_DirN_
CutN_FTS_FromP_BP
Clip
WebCut:
W_Clip_Cope_Left
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FTS_FromP
BP - F_SlopeRight_DirN_
CutN_FTS_FromP_BP
Bounding height =
bounded height and
angle between WebCut:
bounding and Welded_TopSnipe_
bounded web left < 90 Angle_Equal_Left
deg
BP - Welded_TopSnipe_
Angle_Equal_L_BP
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FTS_FromP
BP - F_SlopeRight_DirN_
CutN_FTS_FromP_BP

WebCut:
W_Welded_Slope_Left
Bounding height * 2/3 FlangeCut:
Welded/
+ 25 mm <= bounded EA, UA - F_SlopeRight_DirN_
Clip
height CutN_FTS_FromP
BP - F_SlopeRight_DirN_
CutN_FTS_FromP_BP

Intergraph Smart® 3D 2D Symbols Reference Data Guide 212

 Profile End Cuts

Bounding Previews
End
Object
Cut End Condition Item Name Web Flange
/Bounding
Type
Side

WebCut:
W_Clip_Right
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FTS_FromP
BP - F_SlopeRight_DirN_
CutN_FTS_FromP_BP

WebCut:
W_Clip_LeftWithRadius
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FTS_FromP
BP - F_SlopeRight_DirN_
CutN_FTS_FromP_BP

WebCut:
BP - W_SnipWithRadius_Left
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FTS_FromP
BP - F_SlopeRight_DirN_
CutN_FTS_FromP_BP

WebCut:
W_Welded_StraightCut
Bounding height * 2/3 FlangeCut:
+ 25 mm > bounded EA, UA - F_StraightCut_
height FromB
BP - F_StraightCut_
FromB_BP

WebCut:
W_Welded_Slope_Right
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FTS_FromP
BP - F_SlopeRight_DirN_
CutN_FTS_FromP_BP
BUT/BUTL2 Bounding height =
Welded
- Web Right bounded height WebCut:
Welded_TopSnipe_
Angle_Equal
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FTS_FromP
BP - F_SlopeRight_DirN_
CutN_FTS_FromP_BP

Intergraph Smart® 3D 2D Symbols Reference Data Guide 213

 Profile End Cuts

Bounding Previews
End
Object
Cut End Condition Item Name Web Flange
/Bounding
Type
Side

WebCut:
W_Clip_Cope_Right
FlangeCut:
EA, UA - F_StraightCut_DirN_
CutN_FromP
BP - F_StraightCut_DirN_
CutN_FromP_BP
Bounding height =
bounded height and
angle between WebCut:
bounding and Welded_TopSnipe_
bounded web left > 90 Angle_Equal
deg
BP - Welded_TopSnipe_
Angle_Equal_BP
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FTS_FromP
BP - F_SlopeRight_DirN_
CutN_FTS_FromP_BP
Clip
WebCut:
W_Clip_Cope_Right
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FTS_FromP
BP - F_SlopeRight_DirN_
CutN_FTS_FromP_BP
Bounding height =
bounded height and
angle between WebCut:
bounding and Welded_TopSnipe_
bounded web left < 90 Angle_Equal
deg
BP - Welded_TopSnipe_
Angle_Equal_BP
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FTS_FromP
BP - F_SlopeRight_DirN_
CutN_FTS_FromP_BP

WebCut:
W_Welded_Slope_Right
Bounding height * 2/3 FlangeCut:
Welded/
+ 25 mm < bounded EA, UA - F_SlopeRight_DirN_
Clip
height CutN_FTS_FromP
BP - F_SlopeRight_DirN_
CutN_FTS_FromP_BP

Intergraph Smart® 3D 2D Symbols Reference Data Guide 214

 Profile End Cuts

Bounding Previews
End
Object
Cut End Condition Item Name Web Flange
/Bounding
Type
Side

WebCut:
W_Clip_RightWithRadius
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FTS_FromP
BP - F_SlopeRight_DirN_
CutN_FTS_FromP_BP

WebCut:
BP - W_SnipWithRadius
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FTS_FromP
BP - F_SlopeRight_DirN_
CutN_FTS_FromP_BP

WebCut:
W_Welded_StraightCut
Bounding height * 2/3 FlangeCut:
+ 25 mm > bounded EA, UA - F_StraightCut_
height FromB
BP - F_StraightCut_
FromB_BP

Bounded Section Type: BUT, BUTL2

Bounding Previews
Object/ End Cut End
Item Name Web Flange
Bounding Type Condition
Side

WebCut:
W_Clip_BUT
FlangeCut:
BUT - F_Sniped_DirN_
CutN_FromP
BUTL2 - F_SnipedAngle_DirN_
CutN_FromP
Plate Clip Any
WebCut:
BUTL3 - W_Welded_StraightCut2
FlangeCut:
BUT - F_Sniped_DirN_
CutN_FromP
BUTL2 - F_SnipedAngle_DirN_
CutN_FromP

Intergraph Smart® 3D 2D Symbols Reference Data Guide 215

 Profile End Cuts

Bounding Previews
Object/ End Cut End
Item Name Web Flange
Bounding Type Condition
Side

WebCut:
W_Welded_StraightCut
Welded Any
FlangeCut:
F_StraightCut_FromB

WebCut:
W_Welded_Slope_Right
FlangeCut:
BUT - F_Sniped_DirN_
CutN_FromP
BUTL2 - F_SnipedAngle_DirN_
Bounding CutN_FromP
height <
bounded
height WebCut:
W_BUTSnipe_Right
FlangeCut:
Clip BUT - F_Sniped_DirN_CutN_
FromP
BUTL2 - F_SnipedAngle_DirN_
CutN_FromP

WebCut:
W_Clip_BUT
Bounding
FlangeCut:
FB - Web height >
BUT - F_Sniped_DirN_CutN_
Right bounded
FromP
height
BUTL2 - F_SnipedAngle_DirN_
CutN_FromP

WebCut:
W_Welded_Slope_Right
FlangeCut:
BUT - F_Sniped_DirC_CutC_
FromP
BUTL2 - F_SnipedAngle_DirC_
Bounding CutC_FromP
height <
Weld
bounded
height WebCut:
W_BUTSnipe_Right
FlangeCut:
BUT - F_Sniped_DirN_CutN_
FromP
BUTL2 - F_SnipedAngle_DirN_
CutN_FromP

Intergraph Smart® 3D 2D Symbols Reference Data Guide 216

 Profile End Cuts

Bounding Previews
Object/ End Cut End
Item Name Web Flange
Bounding Type Condition
Side

Bounding WebCut:
height > W_Welded_StraightCut
bounded FlangeCut:
height F_StraightCut_FromB

WebCut:
W_Welded_Slope_Left
FlangeCut:
BUT - F_Sniped_DirN_CutN_
FromP
BUTL2 - F_SnipedAngle_DirN_
Bounding CutN_FromP
height <
bounded
height WebCut:
W_BUTSnipe_Left
FlangeCut:
Clip BUT - F_Sniped_DirN_
CutN_FromP
BUTL2 - F_SnipedAngle_DirN_
BP/UA/EA - CutN_FromP
Web Left
FB - Web Left
WebCut:
W_Clip_BUT
Bounding
FlangeCut:
height >
BUT - F_Sniped_DirN_
bounded
CutN_FromP
height
BUTL2 - F_SnipedAngle_DirN_
CutN_FromP

WebCut:
W_Welded_Slope_Left
Bounding
FlangeCut:
height <
Weld BUT - F_Sniped_DirC_CutC_
bounded
FromP
height
BUTL2 - F_SnipedAngle_DirC_
CutC_FromP

Intergraph Smart® 3D 2D Symbols Reference Data Guide 217

 Profile End Cuts

Bounding Previews
Object/ End Cut End
Item Name Web Flange
Bounding Type Condition
Side

WebCut:
W_BUTSnipe_Left
FlangeCut:
BUT - F_Sniped_DirN_CutN_
FromP
BUTL2 - F_SnipedAngle_DirN_
CutN_FromP

Bounding
height > WebCut: W_Welded_StraightCut
bounded FlangeCut: F_StraightCut_FromB
height

WebCut:
W_Welded_Slope_Right
FlangeCut:
BUT - F_Sniped_DirN_
Bounded CutN_FromP
height > BUTL2 - F_SnipedAngle_
125 mm DirN_CutN_FromP
and
bounding
height < WebCut:
bounded W_SnipWithRadius_Flange
height FlangeCut:
BUT - F_Sniped_DirN_
CutN_FromP
BUTL2 - F_SnipedAngle_DirN_
EA/UA/B_L3/ CutN_FromP
BUT/BUTL2 - Welded
Web Right WebCut:
W_RadiusBUT_Welded_Right
FlangeCut:
BUT - F_Sniped_DirN_
Bounded CutN_FromP
height < BUTL2 - F_SnipedAngle_DirN_
125 mm CutN_FromP
and
bounding
height < WebCut:
bounded W_SnipWithRadius_Flange
height FlangeCut:
BUT - F_Sniped_DirN_CutN_
FromP
BUTL2 - F_SnipedAngle_DirN_
CutN_FromP

Intergraph Smart® 3D 2D Symbols Reference Data Guide 218

 Profile End Cuts

Bounding Previews
Object/ End Cut End
Item Name Web Flange
Bounding Type Condition
Side

WebCut:
W_CornerRadius_Welded_Right
FlangeCut:
BUT - F_StraightCut_DirC_
Bounded CutC_FromP_PC
height < BUTL2 - F_StraightCut_DirC_
125 mm CutC_FromP_PC
and
bounding
height = WebCut:
bounded Welded_TopSnipe_Angle_Equal
height FlangeCut:
BUT - F_StraightCut_DirC_CutC_
FromP_PC
BUTL2 - F_StraightCut_DirC_
CutC_FromP_PC

Bounding WebCut:
height > W_Welded_StraightCut
bounded FlangeCut:
height F_StraightCut_FromB

WebCut:
W_Welded_Slope_Right
FlangeCut:
BUT - F_Sniped_DirN_CutN_
FromP
BUTL - F_SnipedAngle_DirN_
Bounding CutN_FromP
height <
bounded
height WebCut:
W_SnipWithRadius_Flange
FlangeCut:
Clip BUT - F_Sniped_DirN_CutN_
FromP
BUTL2 - F_SnipedAngle_DirN_
CutN_FromP

WebCut:
W_Clip_BUT
Bounding
FlangeCut:
height >
BUT - F_Sniped_DirN_CutN_
bounded
FromP
height
BUTL2 - F_SnipedAngle_DirN_
CutN_FromP

Intergraph Smart® 3D 2D Symbols Reference Data Guide 219

 Profile End Cuts

Bounding Previews
Object/ End Cut End
Item Name Web Flange
Bounding Type Condition
Side

WebCut:
W_Welded_Slope_Left
FlangeCut:
BUT - F_Sniped_DirN_CutN_
Bounded FromP
height > BUTL2 - F_SnipedAngle_DirN_
125 mm CutN_FromP
and
bounding
height < WebCut:
bounded W_SnipWithRadius_Flange_L
height FlangeCut:
BUT - F_Sniped_DirN_CutN_
FromP
BUTL2 - F_SnipedAngle_DirN_
CutN_FromP

WebCut:
W_RadiusBUT_Welded_Left
FlangeCut:
BUT - F_Sniped_DirN_CutN_
Bounded FromP
height < BUTL2 - F_SnipedAngle_DirN_
125 mm CutN_FromP
and
BUT - Web
Welded bounding
Left WebCut:
height <
bounded W_SnipWithRadius_Flange_L
height FlangeCut:
BUT - F_Sniped_DirN_CutN_
FromP
BUTL2 - F_SnipedAngle_DirN_
CutN_FromP

WebCut:
W_CornerRadius_Welded_Left
FlangeCut:
BUT - F_StraightCut_DirC_
CutC_FromP_PC
Bounded
height < BUTL2 - F_StraightCut_DirC_
125 mm CutC_FromP_PC
and
bounding WebCut:
height = Welded_TopSnipe_Angle_
bounded Equal_Left
height
FlangeCut:
BUT - F_StraightCut_DirC_CutC_
FromP_PC
BUTL - F_StraightCut_DirC_
CutC_FromP_PC)

Intergraph Smart® 3D 2D Symbols Reference Data Guide 220

 Profile End Cuts

Bounding Previews
Object/ End Cut End
Item Name Web Flange
Bounding Type Condition
Side

Bounding WebCut:
height > W_Welded_StraightCut
bounded FlangeCut:
height F_StraightCut_FromB

WebCut:
W_Welded_Slope_Left
FlangeCut:
BUT - F_Sniped_DirN_CutN_
FromP
BUTL2 - F_SnipedAngle_
Bounding DirN_CutN_FromP
height <
bounded
height WebCut:
W_SnipWithRadius_Flange_L
FlangeCut:
Clip BUT - F_Sniped_DirN_
CutN_FromP
BUTL - F_SnipedAngle_DirN_
CutN_FromP

WebCut:
W_Clip_BUT
Bounding
FlangeCut:
height >
BUT - F_Sniped_DirN_
bounded
CutN_FromP
height
BUTL2 - F_SnipedAngle_DirN_
CutN_FromP

WebCut:
W_Welded_Slope_Right
FlangeCut:
BUT - F_Sniped_DirN_
Bounded CutN_FromP
height > BUTL2 - F_SnipedAngle_DirN_
125 mm CutN_FromP
BP - Web and
Welded
Right bounding
height < WebCut:
bounded W_SnipWithRadius_Flange_BP
height FlangeCut:
BUT - F_Sniped_DirN_
CutN_FromP
BUTL2 - F_SnipedAngle_DirN_
CutN_FromP

Intergraph Smart® 3D 2D Symbols Reference Data Guide 221

 Profile End Cuts

Bounding Previews
Object/ End Cut End
Item Name Web Flange
Bounding Type Condition
Side

WebCut:
W_RadiusBUT_Welded_Right
FlangeCut:
BUT - F_Sniped_DirN_
Bounded CutN_FromP
height < BUTL2 - F_SnipedAngle_DirN_
125 mm CutN_FromP
and
bounding
height < WebCut:
bounded W_SnipWithRadius_Flange_BP
height FlangeCut:
BUT - F_Sniped_DirN_
CutN_FromP
BUTL2 - F_SnipedAngle_DirN_
CutN_FromP

Bounding WebCut:
height > W_Welded_Slope_Right
bounded
height and FlangeCut:
bounding BUT - F_Sniped_DirN_
height * 2/3 CutN_FromP
+ 25 mm <
bounded BUTL2 - F_SnipedAngle_DirN_
height CutN_FromP

Bounding WebCut:
height * 2/3 W_Welded_StraightCut
+ 25 mm >
Bounded FlangeCut:
Height F_StraightCut_FromB

WebCut:
W_Welded_Slope_Right
FlangeCut:
BUT - F_Sniped_DirN_
CutN_FromP
BUTL2 - F_SnipedAngle_DirN_
Bounding CutN_FromP
height <
Clip
bounded
height WebCut:
W_SnipWithRadius_Flange_BP
FlangeCut:
BUT - F_Sniped_DirN_
CutN_FromP
BUTL2 - F_SnipedAngle_DirN_
CutN_FromP

Intergraph Smart® 3D 2D Symbols Reference Data Guide 222

 Profile End Cuts

Bounding Previews
Object/ End Cut End
Item Name Web Flange
Bounding Type Condition
Side

WebCut:
W_Clip_BUT
Bounding
FlangeCut:
height >
BUT - F_Sniped_DirN_
bounded
CutN_FromP
height
BUTL2 - F_SnipedAngle_DirN_
CutN_FromP

WebCut:
W_Welded_Slope_Left
FlangeCut:
BUT - F_Sniped_DirN_
CutN_FromP
BUTL2 - F_SnipedAngle_DirN_
Bounding CutN_FromP
height <
bounded
height WebCut:
W_SnipWithRadius_Flange_L
FlangeCut:
BUT - F_Sniped_DirN_
CutN_FromP
BUTL2 - F_SnipedAngle_DirN_
CutN_FromP

Default:
WebCut:
W_Welded_Slope_Left
FlangeCut:
BUTL2 - Web
Welded BUT - F_Sniped_DirN_CutN_
Left
FromP
BUTL2 - F_SnipedAngle_DirN_
CutN_FromP

Optional:
WebCut:
Bounding
W_CornerRadius_Welded_Left
height =
bounded FlangeCut:
height BUT - F_StraightCut_DirC_
CutC_FromP_PC
BUTL2 - F_StraightCut_DirC_
CutC_FromP_PC

Optional:
WebCut:
Welded_TopSnipe_Angle_
Equal_Left
FlangeCut:
BUT - F_StraightCut_DirC_
CutC_FromP_PC

Intergraph Smart® 3D 2D Symbols Reference Data Guide 223

 Profile End Cuts

Bounding Previews
Object/ End Cut End
Item Name Web Flange
Bounding Type Condition
Side
BUTL2 - F_StraightCut_DirC_
CutC_FromP_PC

Bounding WebCut:
height > W_Welded_StraightCut
bounded FlangeCut:
height F_StraightCut_FromB

WebCut:
W_Welded_Slope_Left
FlangeCut:
BUT - F_Sniped_DirN_
CutN_FromP
BUTL2 - F_SnipedAngle_
Bounding DirN_CutN_FromP
height <
bounded
height WebCut:
W_SnipWithRadius_Flange_L
FlangeCut:
Clip BUT - F_Sniped_DirN_
CutN_FromP
BUTL2 - F_SnipedAngle_DirN_
CutN_FromP

WebCut:
W_Clip_BUT
Bounding
FlangeCut:
height >
BUT - F_Sniped_DirN_
bounded
CutN_FromP
height
BUTL2 - F_SnipedAngle_DirN_
CutN_FromP

Intergraph Smart® 3D 2D Symbols Reference Data Guide 224

 Profile End Cuts

Bounded Section Type: FB

Bounding Preview (Web)
End
Object/
Cut End Condition Web Cut Item Name
Bounding
Type
Side

Default:
W_Clip_Top_Snip

Optional:
Clip/ W_Welded_Slope_Plate
Plate Any
Welded

Optional:
W_Welded_Slope_Plate_KS20

Bounding W_Welded_Slope_Left
height <
bounded height

Clip
Bounding W_Welded_Slope_Left2
height >
bounded height

Bounding W_Welded_Slope_Left2
BP/UA/EA - height <
Web Left bounded height
FB - Web
Left

Bounding Default:
height = W_Welded_StraightCut
Welded bounded height

Optional:
W_Welded_StraightCut

Intergraph Smart® 3D 2D Symbols Reference Data Guide 225

 Profile End Cuts

Bounding Preview (Web)

End
Object/
Cut End Condition Web Cut Item Name
Bounding
Type
Side

Default:
W_Welded_Slope_Left2

Bounding
height >
bounded height

Optional:
W_Welded_Slope_Left2

Bounding
height < W_Welded_Slope_ Right
bounded height

Clip

Bounding
height > W_Clip_Top_Snip
bounded height

Bounding
height < W_Welded_Slope_ Right
bounded height

FB - Web
Right

Default:
W_Welded_Slope_ Right

Bounding
Welded height =
bounded height

Optional:
W_Welded_StraightCut

Bounding
height > W_Welded_StraightCut
bounded height

Intergraph Smart® 3D 2D Symbols Reference Data Guide 226

 Profile End Cuts

Bounding Preview (Web)

End
Object/
Cut End Condition Web Cut Item Name
Bounding
Type
Side

W_Welded_Slope_Right

Bounded height
> bounding
height *2/3 + 25
mm

Welded W_SnipWithRadius

EA/UA/
B_L3/ BUT/
BUTL2 -
Web Right
Bounded height
< bounding
W_Welded_StraightCut
height *2/3 + 25
mm

Clip Any W_Clip_Top_Snip

W_Welded_Slope_Right

Bounding
height <
bounded height

W_SnipWithRadius_BP

BP - Web
Welded
Right

Bounding
height = W_CopeBulb_Flange
bounded height

Bounding
height - flange
W_Welded_Slope_Right
thickness <
bounded height

Intergraph Smart® 3D 2D Symbols Reference Data Guide 227

 Profile End Cuts

Bounding Preview (Web)

End
Object/
Cut End Condition Web Cut Item Name
Bounding
Type
Side

Other condition W_Welded_StraightCut

Clip Any W_Clip_Top_Snip

W_Welded_Slope_Left

Bounded height
> bounding
height * 2 / 3 +
25 mm

W_SnipWithRadius_Left
Welded

BUT/BUTL2
- Web Left

bounded height
< bounding
W_Welded_StraightCut
height *2/3 + 25
mm

Clip Any W_Clip_Top_Snip

Intergraph Smart® 3D 2D Symbols Reference Data Guide 228

 Profile End Cuts

Bounded with Profile Top (Tripping Case)

Bounded Section Type: All
Bounde Previews
d End Cut End
Item Name Web Flange
Section Type Condition
Type

Default:
WebCut:
W_BeyondBoundaryExtend
FlangeCut:
EA/UA/BUTL3 - F_SlopeRight_DirC_
CutC_FromP
Lapped
BUT - F_Sniped_DirC_
CutC_FromP
BUTL2 - F_SnipedAngle_DirC_
CutC_FromP
Weld/
All BP - F_SlopeRight_DirC_
Clip
CutC_FromP_BP

Default:
WebCut:
W_Welded_StraightCut

Bounded FlangeCut:
BP - F_StraightCut_
FromB_BP
Others - F_StraightCut_
FromB

Free End
Bounded Section Type: All (except ER)
Bounde Previews
d End Cut
End Condition Item Name Web Flange
Section Type
Type

Default:
WebCut::
W_AlongAxis_StraightCut
All "FreeEndCut
Weld/ FlangeCut:
DirectionType" is
BP/Angle Clip "AlongGlobalAxis" BP - F_StraightCut_DirC_
CutC_FromP_BP
Others - F_StraightCut_DirC_
CutC_FromP

Intergraph Smart® 3D 2D Symbols Reference Data Guide 229

 Profile End Cuts

Bounde Previews
d End Cut
End Condition Item Name Web Flange
Section Type
Type

Default:
WebCut:
W_Welded_StraightCut
FlangeCut:
BP - F_StraightCut_DirN_
CutN_FromP_BP
Others - F_StraightCut_DirN_
"FreeEndCut CutN_FromP
DirectionType" is
"Normal" Optional:
WebCut:
W_SlopBeyond
FlangeCut:
BP - F_StraightCut_DirN_
CutN_FromP_BP
Others - F_StraightCut_DirN_
CutN_FromP

Optional:
WebCut:
W_BeyondBoundaryExtend
"FreeEndCut FlangeCut:
Weld DirectionType" is BP - F_StraightCut_DirN_
"Normal" CutN_FromP_BP
Others -
F_StraightCut_DirN_CutN_
FromP

Optional:
WebCut:
FreeEndW_Radius_75
FreeEndW_Radius_100

Clip FreeEndW_Radius_150
FlangeCut:
BP - F_StraightCut_DirN_
CutN_FromP_BP
Others - F_StraightCut_DirN_
CutN_FromP

Optional:
WebCut:
W_SnipWithRadius_1

Angle Snip FlangeCut:

BP - F_StraightCut_DirN_
CutN_FromP_BP
Others - F_StraightCut_DirN_
CutN_FromP

Intergraph Smart® 3D 2D Symbols Reference Data Guide 230

 Profile End Cuts

Bounde Previews
d End Cut
End Condition Item Name Web Flange
Section Type
Type

Optional
WebCut
W_CnipRadius_15DEG
W_SnipRadius_30DEG
W_SnipRadius_45DEG
FlangeCut:
BP - F_StraightCut_DirN_
CutN_FromP_BP
Others - F_StraightCut_DirN
CutN_FromP

Edge Reinforcement End Cuts

Previews (Web)
Bounding
Object End Cut End
Item Name
/Bounding Type Condition
Side

Default:
WebCut:
W_Welded_StraightCut

Weld/
All/Free End Any
Clip

Optional:
WebCut:
W_F1_ER_PC
W_F1_ER_PC_1

Intergraph Smart® 3D 2D Symbols Reference Data Guide 231

 Profile End Cuts

Snip End Cuts

Bounding Previews
Bounded
Object End
Section Item Name Web Flange
/Bounding Condition
Type
Side

WebCut:
W_BUTSnipe
FlangeCut:
BUT/ BUT - F_Sniped_DirN_
All/ CutN_FromP
BUTL2/ Any
FreeEnd
BUTL3 BUTL2 - F_SnipedAngle_DirN_
CutN_FromP (For BUTL2)
BUTL3 - F_SlopeRight_DirN_
CutN_FromP

Default:
WebCut:
W_Snip_Top_Snip
W_Snip_Top_Snip_45DEG
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FromP
BP - F_SlopeRight_DirN_
CutN_FromP_BP
EA, UA - F_SlopeRight_DirN_
CutN_FromP
BP - F_SlopeRight_DirN_
CutN_FromP_BP

Optional:
WebCut:
All/ W_SnipRadius_30
EA, UA, BP Any
FreeEnd
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FromP
BP - F_SlopeRight_DirN_
CutN_FromP_BP

Optional:
WebCut:
W_SnipRadius_15DEG
W_SnipRadius_30DEG
W_SnipRadius_45DEG
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FromP
BP - F_SlopeRight_DirN_
CutN_FromP_BP

Intergraph Smart® 3D 2D Symbols Reference Data Guide 232

 Profile End Cuts

Bounding Previews
Bounded
Object End
Section Item Name Web Flange
/Bounding Condition
Type
Side

Optional:
WebCut:
W_SnipRadius_150
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FromP
BP - F_SlopeRight_DirN_
CutN_FromP_BP

Optional:
WebCut:
W_SlopBeyond
FlangeCut:
EA, UA - F_SlopeRight_DirN_
CutN_FromP
BP - F_SlopeRight_DirN_
CutN_FromP_BP

Optional:
WebCut:
W_Snip_StrightCutWithAngle
FlangeCut:
EA, UA - F_StraightCut_DirN_
CutN_FromP
BP - F_StraightCut_DirN_
CutN_FromP_BP

Optional:
WebCut:
W_Snip_StrightCutWithAngle_45
FlangeCut:
EA, UA - F_StraightCut_DirN_
CutN_FromP
BP - F_StraightCut_DirN_
CutN_FromP_BP

Optional:
WebCut:
BP - WebCut_SnipRadius
FlangeCut:
EA, UA - F_StraightCut_DirN_
CutN_FromP
BP - F_StraightCut_DirN_
CutN_FromP_BP

Intergraph Smart® 3D 2D Symbols Reference Data Guide 233

 Profile End Cuts

Bounding Previews
Bounded
Object End
Section Item Name Web Flange
/Bounding Condition
Type
Side

Optional:
BP - Free_WebCut_Tape
FlangeCut:
EA, UA - F_StraightCut_DirN_
CutN_FromP
BP - F_StraightCut_DirN_
CutN_FromP_BP

Optional:
BP - Free_WebCut_
C1AlligatorEnd
FlangeCut:
EA, UA - F_StraightCut_DirN_
CutN_FromP
BP - F_StraightCut_DirN_
CutN_FromP_BP

Optional:
BP - Free_WebCut_
C2AlligatorPCEnd
FlangeCut:
EA, UA - F_StraightCut_DirN_
CutN_FromP
BP - F_StraightCut_DirN_
CutN_FromP_BP

Optional:
BP - W_SnipBottomRadius
FlangeCut:
EA, UA - F_StraightCut_DirN_
CutN_FromP
BP - F_StraightCut_DirN_
CutN_FromP_BP

Default:
WebCut:
W_Snip_Top_Snip

All/ W_Snip_Top_Snip_45DEG
FB Any
FreeEnd

Optional:
WebCut:
W_SnipRadius_30

Intergraph Smart® 3D 2D Symbols Reference Data Guide 234

 Profile End Cuts

Bounding Previews
Bounded
Object End
Section Item Name Web Flange
/Bounding Condition
Type
Side

Optional:
WebCut:
W_SnipRadius_150

Optional:
WebCut:
W_SlopBeyond

Optional:
WebCut:
W_Snip_StrightCutWithAngle

Optional:
WebCut:
W_Snip_StrightCutWithAngle_45

Optional:
WebCut:
W_Snip_StrightCutWithAngle_60

Default:
WebCut:
FreeEndWebCut_F1_ER
FreeEndWebCut_F1_ER2

Optional:
OnEdge
WebCut:
All/ FreeEndWebCut_F1_ER_SS
ER
FreeEnd

Optional:
WebCut:
W_SlopBeyond_ER

WebCut:
OnFace
W_Snip_Top_Snip

Intergraph Smart® 3D 2D Symbols Reference Data Guide 235

 Profile End Cuts

Cut Back End Cuts

Bounded Section Type: All
Bounding Previews
Object End Cut End
Item Name Web Flange
/Bounding Type Condition
Side

Default:
WebCut:
W_CutBack_StrighatCut_
CutC_DirC
FlangeCut:
EA, UA, BUTL3 - F_SlopeRight_
DirC_CutC_FromP
BUT - F_Sniped_DirC_
CutC_FromP
BUTl2 - F_SnipedAngle_DirC_
CutC_FromP
BP - F_SlopeRight_DirC_
CutC_FromP_BP
Others - F_StraightCut_DirC_
CutC_FromP
All/FreeEnd CutBack Any
Optional:
WebCut:
W_CutBack_StrighatCut_
CutN_DirN
FlangeCut:
EA, UA, BUTL3 - F_SlopeRight_
DirN_CutN_FromP
BUT - F_Sniped_ DirN_
CutN_FromP
BUTL2 - F_SnipedAngle_
DirN_CutN_FromP
BP - F_SlopeRight_
DirN_CutN_FromP_BP
Others - F_StraightCut_DirN_
CutN_FromP

Intergraph Smart® 3D 2D Symbols Reference Data Guide 236

 Profile End Cuts

End-to-End End Cuts

Section SplitEndTo Previews
End Condition Item Name
Type EndCase Web Flange

Part1:
WebCut:
WebCut_PC_Taper
Part1 height >
Part2 height

Part2:
WebCut:
FB WebCut_C1End
(Except NoAngle
ER)

Part1:
WebCut:
WebCut_C1PCEnd
Part1 height =
Part2 height
Part2:
WebCut:
WebCut_C1End

Part1:
WebCut:
WebCut_PCER_Taper
WebCut_PCER_Taper2

Part1 height >

Part2 height

Part2:
ER NoAngle WebCut:
WebCut_C1End

Part1:
Part1 height =
Part2 height WebCut:
WebCut_C1PCEnd

Intergraph Smart® 3D 2D Symbols Reference Data Guide 237

 Profile End Cuts

Section SplitEndTo Previews

End Condition Item Name
Type EndCase Web Flange

Part2:
WebCut:
WebCut_C1End

Part1:
WebCut:
WebCut_C1PCEnd

Part2:
Part1 height <
Part2 height WebCut:
WebCut_ER_Taper

WebCut:
WebCut_ER_Taper2

AngleWeb
Square Part1:
Flange WebCut:
or WebCut_PC_
SeamAngleCase2_FB
AngleWeb
Bevel All
Flange
FB Part2:
or
(Except
ER) or AngleWeb WebCut:
ER Angle WebCut_
Flange SeamAngleCase2_FB_2

Distance
Part1:
Web
Distance All WebCut:
Flange WebCut_PC_SeamAngle
Case4_FB
or

Intergraph Smart® 3D 2D Symbols Reference Data Guide 238

 Profile End Cuts

Section SplitEndTo Previews

End Condition Item Name
Type EndCase Web Flange
OffsetWeb
Offset
Part2:
Flange
WebCut:
WebCut_
SeamAngleCase4_FB_2

Part1:
WebCut:
WebCut_
C1AlligatorPCEnd
FlangeCut:
EA, UA - FlangeCut_
Slope_Angle
BUT - FlangeCut_
Part1 height - Slope_BUT
Part2 > 25 mm
Part2:
WebCut:
WebCut_C1End
FlangeCut:
EA/UA - FlangeCut_
W1End
BUT - FlangeCut_
W4End
EA/UA/B
No Angle
UT
Part1:
WebCut:
WebCut_C1PCEnd
FlangeCut: EA/UA -
FlangeCut_SlopePCEnd_
Angle

Part1 height = BUT -

Part2 height FlangeCut_SlopePCEnd_
and Part1 BUT
flange width >
Part2 flange
width Part2:
WebCut:
WebCut_C1End
FlangeCut:
EA/UA -
FlangeCut_W1End
BUT - FlangeCut_W4End

Intergraph Smart® 3D 2D Symbols Reference Data Guide 239

 Profile End Cuts

Section SplitEndTo Previews

End Condition Item Name
Type EndCase Web Flange

Part1:
WebCut:
WebCut_C1PCEnd
FlangeCut: EA/UA -
FlangeCut_W1PCEnd

Part1 height = BUT -

Part2 height FlangeCut_W4PCEnd
and Part1
flange width =
Part2 flange Part2:
width WebCut:
WebCut_C1End
FlangeCut:
EA/UA -
FlangeCut_W1End
BUT/BUTL2 -
FlangeCut_W4End

Part1:
WebCut:
WebCut_C1PCEnd
FlangeCut:
EA/UA -
FlangeCut_W1PCEnd

Part1 height = BUT -

Part2 height FlangeCut_W4PCEnd
and Part1
flange width < Part2:
Part2 flange
width WebCut:
WebCut_C1End
FlangeCut:
EA/UA -
FlangeCut_Slope_
Angle
BUT - FlangeCut_Slope_
BUT

Part1:
0 < Part1 height WebCut:
- Part2 height < WebCut_C1PCEnd
25 mm and 0 <
Part2 height - FlangeCut:
Part1 height < EA/UA -
25 mm FlangeCut_W1End
BUT - FlangeCut_W4End

Intergraph Smart® 3D 2D Symbols Reference Data Guide 240

 Profile End Cuts

Section SplitEndTo Previews

End Condition Item Name
Type EndCase Web Flange

Part2:
WebCut:
WebCut_C1End
FlangeCut:
EA/UA -
FlangeCut_W1End
BUT - FlangeCut_W4End

Part1:
WebCut:
WebCut_C1PCEnd
FlangeCut:
EA/UA -
FlangeCut_W1End
BUT - FlangeCut_W4End
Part2 Height-
Part1 Height > Part2:
25 mm
WebCut:
WebCut_C1AlligatorEnd
FlangeCut:
EA/UA -
FlangeCut_Slope_
Angle
BUT -
FlangeCut_Slope_BUT

Part1:
WebCut:
WebCut_C1AlligatorPCEn
d
FlangeCut:
BP - FlangeCut_Slope_
Bulb
BUTL2 -
Part1 Height- FlangeCut_Slope_
BP/ BL2
NoAngle Part2 Height >
BUTL2
25mm
Part2:
WebCut:
WebCut_C1End
FlangeCut:
BP - FlangeCut_
W1End_BP
BUTL2 - FlangeCut_
W4End

Intergraph Smart® 3D 2D Symbols Reference Data Guide 241

 Profile End Cuts

Section SplitEndTo Previews

End Condition Item Name
Type EndCase Web Flange

Part1:
WebCut:
WebCut_C1PCEnd
FlangeCut: BP -
FlangeCut_W1PCEnd_
BP
BUTL2 - FlangeCut_
W4PCEnd
Part1 height =
Part2 height
Part2:
WebCut:
WebCut_C1End
FlangeCut:
BP -
FlangeCut_W1End_BP
BUTL2 -
FlangeCut_W4End

Part1:
WebCut:
WebCut_C1PCEnd
FlangeCut:
BP - FlangeCut_W1End_
BP
0 < Part1 height BUTL2 -
- Part2 height < FlangeCut_W4End
25 mm and 0 <
Part2 height -
Part1's height < Part2:
25 mm WebCut:
WebCut_C1End
FlangeCut:
BP -
FlangeCut_W1End_BP
BUTL2 -
FlangeCut_W4End

Part1:
WebCut:
WebCut_C1PCEnd
Part2 height -
Part1 height > FlangeCut:
25 mm BP - FlangeCut_
W1End_BP
BUTL2 - FlangeCut_
W4End

Intergraph Smart® 3D 2D Symbols Reference Data Guide 242

 Profile End Cuts

Section SplitEndTo Previews

End Condition Item Name
Type EndCase Web Flange

Part2:
WebCut:
WebCut_C1AlligatorEnd
FlangeCut:
BP -
FlangeCut_Slope_Bulb
BUTL2 -
FlangeCut_Slope_
BL2

Part1:
WebCut:
WebCut_PC_
SeamAngleCase1
AngleWeb
Square All
Flange
Part2:
WebCut:
WebCut_SeamAngleCase
1_2

Part1:
WebCut:
WebCut_PC_
SeamAngleCase2
All AngleWeb
(Except Bevel All
FB) Flange
Part2:
WebCut:
WebCut_SeamAngleCase
2_2

Part1:
WebCut:
WebCut_PC_
SeamAngleCase3
AngleWeb
Angle All
Flange
Part2:
WebCut:
WebCut_SeamAngleCase
3_2

Intergraph Smart® 3D 2D Symbols Reference Data Guide 243

 Profile End Cuts

Section SplitEndTo Previews

End Condition Item Name
Type EndCase Web Flange

Part1:
WebCut:
WebCut_PC_
SeamAngleCase4
Distance
Web
All
Distance
Flange Part2:
WebCut:
WebCut_SeamAngleCase
4_2

Part1:
WebCut:
WebCut_PC_SeamAngleC
ase5
OffsetWeb
Offset All
Flange
Part2:
WebCut:
WebCut_SeamAngleCase
5_2

Part1:
WebCut:
WebCut_AlongAxisPCEnd
FlangeCut:
Part1 height = FlangeCut_AlongAxisA_
Part2 height SlopeRight_PCEnd
and Part1
flange width >
Part2 flange Part2:
Along width WebCut:
Global WebCut_AlongAxisEnd
EA/UA
Axis or
AlongSeam FlangeCut:
FlangeCut_AlongAxisA_
SlopeRight_End

Part1:
WebCut:
Other WebCut_AlongAxisPCEnd
conditions
FlangeCut:
FlangeCut_AlongAxisAPC
End

Intergraph Smart® 3D 2D Symbols Reference Data Guide 244

 Profile End Cuts

Section SplitEndTo Previews

End Condition Item Name
Type EndCase Web Flange

Part2:
WebCut:
WebCut_AlongAxisEnd
FlangeCut:
FlangeCut_AlongAxisAEnd

Part1:
WebCut:
WebCut_AlongAxisPCEnd
FlangeCut:
Part1 height = FlangeCut_AlongAxisT_
Part2 height Slope_PCEnd
and Part1
flange width >
Part2 flange Part2:
width
WebCut:
WebCut_AlongAxisEnd
FlangeCut:
FlangeCut_AlongAxisT_
Slope_End
BUT
Part1:
Along
WebCut:
Global
WebCut_AlongAxisPCEnd
Axis or
AlongSeam FlangeCut:
FlangeCut_AlongAxisTPC
Other End
conditions
Part2:
WebCut:
WebCut_AlongAxisEnd
FlangeCut:
FlangeCut_AlongAxisTEnd

Part1:
WebCut:
WebCut_AlongAxisPCEnd
FlangeCut:
FlangeCut_AlongAxis
Along APCEnd_BP
Global
BP All
Axis or
AlongSeam Part2:
WebCut:
WebCut_AlongAxisEnd
FlangeCut:
FlangeCut_AlongAxisA
End_BP

Intergraph Smart® 3D 2D Symbols Reference Data Guide 245

 Profile End Cuts

Section SplitEndTo Previews

End Condition Item Name
Type EndCase Web Flange

Part1:
WebCut:
WebCut_AlongAxisPCEnd
FlangeCut:
FlangeCut_AlongAxis
Along
TPCEnd
BUTL2/B Global
All
UTL2 Axis or
AlongSeam Part2:
WebCut:
WebCut_AlongAxisEnd
FlangeCut:
FlangeCut_AlongAxisTEnd

Part1:
WebCut:
Along WebCut_AlongAxisPCEnd
Global
FB All
Axis or
AlongSeam Part2:
WebCut:
WebCut_AlongAxisEnd

Long Box End Cuts

Bounding Previews
Bounded
Object/ End Cut
Section Item Name Web Flange
Bounding Type
Type
Side

WebCut:
Snip
WebCut_LongBoxF1B

FB All

WebCut:
Weld
WebCut_LongBoxC1

Intergraph Smart® 3D 2D Symbols Reference Data Guide 246

 Profile End Cuts

Bounding Previews
Bounded
Object/ End Cut
Section Item Name Web Flange
Bounding Type
Type
Side

WebCut:
WebCut_LongBoxF1
FlangeCut:
Snip EA/UA/BP - FlangeCut_
LongBoxF1
BUT - FlangeCut_
LongBoxF4
Others All
WebCut:
WebCut_LongBoxC1
FlangeCut:
Weld EA/UA/BP - FlangeCut_
LongBoxW1
BUT - FlangeCut_
LongBoxW4

Miter End Cuts

Bounde Bounding Previews
d Object/ End Cut
Item Name Web Flange
Section Bounding Type
Type Side

Part1:
WebCut:
WebCut_C1MiterPc
FlangeCut:
EA/UA/BP - FlangeCut_
W1MiterPC
BUT - FlangeCut_
W4MiterPC
All All All
Part2:
WebCut:
WebCut_C1MiterEnd
FlangeCut:
EA/UA/BP - FlangeCut_
W1MiterEnd
BUT - FlangeCut_
W4MiterEnd

Intergraph Smart® 3D 2D Symbols Reference Data Guide 247

 Profile End Cuts

Bounded by Plate ER
Bounding Previews
Bounded End
Object/
Section Cut Item Name Web Flange
Bounding
Type Type
Side

WebCut:
W_Welded_StraightCut3
FlangeCut:
Lug EA, UA - F_StraightCut_DirN_
CutN_FromP
BP - F_StraightCut_DirN_
CutN_FromP_BP
EA/UA Plate+ER
WebCut:
W_Clip_Cope
FlangeCut:
Clip EA, UA - F_StraightCut_DirN_
CutN_FromP
BP - F_StraightCut_DirN_
CutN_FromP_BP

WebCut:
W_Welded_StraightCut3
FlangeCut:
EA/UA Plate+ER Lug EA, UA - F_StraightCut_DirN_
CutN_FromP
BP - F_StraightCut_DirN_
CutN_FromP_BP

Optional Flange Cut Shapes

For normal flange cuts, you can use the default flange cut type, or select an optional one.
Optional flange cut types are unavailable for end-to-end cuts, long box cuts, or miter
cuts.

Bounded Flange Cut Shape

Section

Straight Cut Slope(Nose = Slope-FTS(Nose =

WebThickness+15mm) WebThickness)

Intergraph Smart® 3D 2D Symbols Reference Data Guide 248

 Profile End Cuts

Bounded Flange Cut Shape

Section

EA/UA/BUTL3 F_StraightCut_DirN_ F_SlopeRight_DirN_ F_SlopeRight_DirN_

CutN_FromP CutN_FromP CutN_FTS_FromP

F_StraightCut_DirC_ F_SlopeRight_DirC_ F_SlopeRight_DirC_

CutC_FromP CutC_FromP CutC_FTS_FromP

F_StraightCut_FromB F_SlopeRight_FromB F_SlopeRight_FTS_FromB

F_SlopeRight_FromB_1

F_StraightCut_DirC_ F_SlopeRight_DirC_ F_SlopeRight_DirC_CutC_

CutC_FromP_PC CutC_FromP_PC FTS_FromP_PC

BP F_StraightCut_DirN_ F_SlopeRight_DirN_ F_SlopeRight_DirN_CutN_

CutN_FromP_BP CutN_FromP_BP FTS_FromP_BP

F_StraightCut_DirC_ F_SlopeRight_DirC_ F_SlopeRight_DirC_CutC_

CutC_FromP_BP CutC_FromP_BP FTS_FromP_BP

F_StraightCut_FromB_BP F_SlopeRight_FromB_BP F_SlopeRight_FTS_FromB_BP

F_StraightCut_DirC_ F_SlopeRight_DirC_ F_SlopeRight_DirC_CutC_

CutC_FromP_BP_PC CutC_FromP_BP_PC FTS_FromP_BP_PC

Straight Cut Slope(Nose = WebThickness + 30mm)

BUT F_StraightCut_DirN_ F_Sniped_DirN_CutN_FromP

CutN_FromP
F_Sniped_DirN_CutN_FromP_1

F_StraightCut_DirC_ F_Sniped_DirC_CutC_FromP
CutC_FromP

F_StraightCut_DirC_ F_Sniped_DirC_CutC_FromP_PC
CutC_FromP_PC
F_Sniped_DirC_CutC_FromP_PC_1

BUTL2 F_StraightCut_DirN_ F_SnipedAngle_DirN_CutN_FromP

CutN_FromP

F_StraightCut_DirC_ F_SnipedAngle_DirC_CutC_FromP
CutC_FromP

F_StraightCut_DirC_ F_SnipedAngle_DirC_CutC_FromP_PC
CutC_FromP_PC

Intergraph Smart® 3D 2D Symbols Reference Data Guide 249

SECTION 13

Member End Cuts

End cut symbols for members are delivered in the following locations:
 Web cuts are in the [Reference Data Folder]\SharedContent\Marine Library\Web
Cuts\Members folder.
 Flange cuts are in the [Reference Data Folder]\SharedContent\Marine Library\Flange
Cuts\Members folder.

In This Section
Along-Axis Web Cuts for Members ................................................ 250
Along-Axis Flange Cuts for Members ............................................ 272
Web Cuts for Split Members .......................................................... 301
Flange Cuts for Split Members ...................................................... 306
Mitered Web Cuts for Members ..................................................... 307
Mitered Flange Cuts for Members ................................................. 308
Free-end Web Cuts for Members .................................................. 309
Free-end Flange Cuts for Members ............................................... 310

Along-Axis Web Cuts for Members

Creates a web cut for a member bounded by the axis curve of the bounding member.
There are separate web cuts for member assembly connections and generic assembly
connections.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 250

 Member End Cuts

Web-penetrated Center Cuts

Name Cross- Description Parameters

Sections
Supported

Web_F All Valid boundaries and

orientations present only a
(generic)
face to the bounding object.

WebTB_F All Valid boundaries and

orientations present only a
(generic)
face to the bounding
member. The bounding
member is an H-beam or
similar.

WebT_F All Valid boundaries and

orientations present only a
(generic)
face to the bounding
member. The bounding
member is a channel with
the flanges up.

WebB_F All Valid boundaries and

orientations present only a
(generic)
face to the bounding
member. The bounding
member is a channel with
the flange down.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 251

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Web_TE_F_BE All Valid boundaries and

orientations present a face,
(generic)
a top edge, and a bottom
edge to the bounding
member.

Web_TE_F_BE_ Rolled Use for an exact fit when

Ellipse sections with both top and bottom
top and bounding edges have a
bottom fillet.
flanges
Valid boundaries and
orientations present a face,
a top edge, and a bottom
edge to the bounding
member.

Web_TE_F_BE_ Rolled Use for an exact fit to the

EllipseTop sections with top edge only when it has a
top flange fillet.
Valid boundaries and
Web_TE_F_BE_El
orientations present a face,
lipseBottom
a top edge, and a bottom
edge to the bounding
member.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 252

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Web_TE_F_BE_ Rolled Use for an exact fit to the

Ellipse sections with bottom edge only when it
bottom flange has a fillet.
Valid boundaries and
orientations present a face,
a top edge, and a bottom
edge to the bounding
member.

Web_F_BE All Valid boundaries and

orientations present a face
(generic)
and a bottom edge to the
bounding member.

Web_F_BE_ All Use for an exact fit to the

Ellipse bottom edge when it has a
fillet.
(generic)
Valid boundaries and
orientations present a face
and a bottom edge to the
bounding member.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 253

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Web_TE_F All Valid boundaries and

orientations present a face
(generic)
and a top edge to the
bounding member.

Web_TE_F_ All Use for an exact fit to the

Ellipse top edge when it has a fillet.
(generic) Valid boundaries and
orientations present a face
and a top edge to the
bounding member.

Web_TF_TE_F All Valid boundaries and

orientations present a face,
(generic)
top edge, and top face to
the bounding member.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 254

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Web_F_BE_BF All Valid boundaries and

orientations present a face,
(generic)
a bottom edge, and a
bottom face to the bounding
member.

Axis_Tube_00 Tube to Tube Tubular member is

bounded to another tubular
member (except on-
member configuration).

Axis_Web_Tube Standard Standard member is

member to bounded to tubular
Tube member: bounded
members web is cut by the
bounding member edge as
shown.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 255

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Axis_Tube_To Standard Standard member is

Center member to bounded to tubular
tube member; bounded
member's web is cut by the
bounding member edge
and corresponding top and
bottom web cut points as
shown.

Axis_Tube_FC Standard Standard member is

AndOS_TOP member to bounded to tubular
tube member; bounded
member's web is cut by the
bounding member edge
and the corresponding top
and bottom web cut points
as shown.

Axis_Tube_FC Standard Standard member is

AndOS_BTM member to bounded to tubular
tube member; bounded
member's web is cut by the
bounding member edge
and the corresponding top
and bottom web cut points
as shown.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 256

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Axis_Tube_OS Standard Standard member is

AndOS member to bounded to tubular
tube member; bounded
member's web is cut by the
bounding member edge
and corresponding top and
bottom web cut points as
shown.

Web-penetrated Top Cuts

All web cuts are available for both member assembly connections and generic assembly
connections.

Name Cross- Description Parameters

Sections
Supported

Inside Hook All Valid boundaries and

Flange Relief orientations present a
Top face and a top edge to
the bounding member.
The bounding member is
still valid if it has a bottom
edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 257

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Inside Hook All Valid boundaries and

Flange Relief orientations present a
Snipe Top face and a top edge to
the bounding member.
The bounding member is
still valid if it has a bottom
edge.

Square Flange All Valid boundaries and

Relief Web Top orientations present a
face and a top edge to
the bounding member.
The bounding member is
still valid if it has a bottom
edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 258

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Square Flange All Valid boundaries and

Relief Web Top orientations present a
Cut Snipe face and a top edge to
the bounding member.
The bounding member is
still valid if it has a bottom
edge.

Square Along All Valid boundaries and

Flange Relief orientations present a
Web Top Cut face and a top edge to
the bounding member.
The bounding member is
still valid if it has a bottom
edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 259

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Square Along All Valid boundaries and

Flange Relief orientations present a
Web Top Cut face and a top edge to
Snipe the bounding member.
The bounding member is
still valid if it has a bottom
edge.

Edge Hook All Valid boundaries and

Flange Relief orientations present a
Outside Web face and a top edge to
Top the bounding member.
The bounding member is
still valid if it has a bottom
edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 260

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Edge Hook All Valid boundaries and

Flange Relief orientations present a
Outside Web face and a top edge to
Top Snipe the bounding member.
The bounding member is
still valid if it has a bottom
edge.

Top Snipe All Valid boundaries and

Outside orientations present a
face and a top edge to
the bounding member.
The bounding member is
still valid if it has a bottom
edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 261

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Top Snipe All Valid boundaries and

Outside orientations present a
Setback face and a top edge to
the bounding member.
The bounding member is
still valid if it has a bottom
edge.

Outside Snipe All Valid boundaries and

Top Offset orientations do not
present a top edge to the
bounding member.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 262

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Edge Hook All Valid boundaries and

Flange Relief orientations present a
Inside Web Top face and a bottom edge
to the bounding member.
The bounding member is
still valid if it has a top
edge.

Top Outside All Valid boundaries and

Hook Flange orientations present a
Relief face and a bottom edge
to the bounding member.
The bounding member is
still valid if it has a top
edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 263

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Top Snipe Standard Standard member is

OutSide _Tube member to bounded to a tubular
Tube member. This web cut is
applicable to members
with a top flange such as
T, and also for members
without a top flange such
as L.

Web-penetrated Bottom Cuts

All web cuts are available for both member assembly connections and generic assembly
connections.

Name Cross- Description Parameters

Sections
Supported

Inside Hook All Valid boundaries and

Flange Relief orientations present a
Bottom face and a bottom edge
to the bounding
member. The bounding
member is still valid if it
has a top edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 264

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Inside Hook All Valid boundaries and

Flange Relief orientations present a
Snipe Bottom face and a bottom edge
to the bounding
member. The bounding
member is still valid if it
has a top edge.

Square Flange All Valid boundaries and

Relief Web orientations present a
Bottom Cut face and a bottom edge
to the bounding
member. The bounding
member is still valid if it
has a top edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 265

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Square Flange All Valid boundaries and

Relief Web orientations present a
Bottom Cut face and a bottom edge
Snipe to the bounding
member. The bounding
member is still valid if it
has a top edge.

Square Along All Valid boundaries and

Flange Relief orientations present a
Web Bottom face and a bottom edge
Cut to the bounding
member. The bounding
member is still valid if it
has a top edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 266

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Square Along All Valid boundaries and

Flange Relief orientations present a
Web Bottom face and a bottom edge
Cut Snipe to the bounding
member. The bounding
member is still valid if it
has a top edge.

Edge Hook All Valid boundaries and

Flange Relief orientations present a
Outside Web face and a bottom edge
Bottom to the bounding
member. The bounding
member is still valid if it
has a top edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 267

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Edge Hook All Valid boundaries and

Flange Relief orientations present a
Outside Web face and a bottom edge
Bottom Snipe to the bounding
member. The bounding
member is still valid if it
has a top edge.

Bottom Snipe All Valid boundaries and

Outside orientations present a
face and a bottom edge
to the bounding
member. The bounding
member is still valid if it
has a top edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 268

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Bottom Snipe All Valid boundaries and

Outside orientations present a
Setback face and a bottom edge
to the bounding
member. The bounding
member is still valid if it
has a top edge.

Outside Snipe All Valid boundaries and

Offset Web orientations present a
Bottom Cut face and a bottom edge
to the bounding
member. The bounding
member is still valid if it
has a top edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 269

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Edge Hook All Valid boundaries and

Flange Relief orientations present a
Inside Web face and a bottom edge
Bottom to the bounding
member. The bounding
member is still valid if it
has a top edge.

Bottom All Valid boundaries and

Outside Hook orientations present a
Flange Relief face and a bottom edge
to the bounding
member. The bounding
member is still valid if it
has a top edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 270

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Bottom Snipe Standard Standard member is

Outside_Tube member to bounded to a tubular
Tube member. This web cut is
applicable to members
with a bottom flange
such as L and also to
members without bottom
flange such as T.

Web Non-penetrated Cuts

There are separate web cuts for member assembly connections and generic assembly
connections.

Name Cross- Description Parameters

Sections
Supported

FlushBoundedDepth All
(generic)

Intergraph Smart® 3D 2D Symbols Reference Data Guide 271

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

FlushActual All
(generic)

Axis_Web_Cope_Ext All Selected only when

BraceType =
(member)
"InsetMember"
and the cut is
between Brace and
Bounded of the
Parent Assembly
Connection (which
creates the Child
brace).

Intergraph Smart® 3D 2D Symbols Reference Data Guide 272

 Member End Cuts

Along-Axis Flange Cuts for Members

Flange-penetrated Center Cuts
There are separate web cuts for member assembly connections and generic assembly
connections.

Name Cross- Description Parameters

Sections
Supported

Flange_F All Valid boundaries and

orientations present only a
(generic)
face to the bounding object.

FlangeTB_F All Valid boundaries and

orientations present only a
(generic)
face to the bounding
member. The bounding
member is an H-beam or
similar.

FlangeT_F All Valid boundaries and

orientations present only a
(generic)
face to the bounding
member. The bounding
member is a channel with
the flanges up.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 273

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

FlangeB_F All Valid boundaries and

orientations present only a
(generic)
face to the bounding
member. The bounding
member is a channel with
the flanges down.

Flange_TE_F_ All Valid boundaries and

BE orientations present a face,
a top edge, and a bottom
(generic)
edge to the bounding
member.

Flange_F_BE All Valid boundaries and

orientations present a face
(generic)
and a bottom edge to the
bounding member.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 274

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Flange_TE_F All Valid boundaries and

orientations present a face
(generic)
and a top edge to the
bounding member.

Flange_TF_TE_ All Valid boundaries and

F orientations present a face,
top edge, and top face to the
(generic)
bounding member.

Flange_F_BE_ All Valid boundaries and

BF orientations present a face,
bottom edge, and bottom
(generic)
face to the bounding
member.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 275

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Axis_Flange Standard Standard member is

_Tube member to bounded to a tubular
Tube member. The bounded
member's flange is cut by
the bounding member edge.

Axis_Flange_ All Selected only when

Variable_Bevel BraceType = InsetMember
and the cut is between
Brace and Bounded of the
Parent Assembly
Connection.

FlangeCut_ Standard Standard member is

Gusset member to bounded to the lateral edge
lateral edge of of a plate part. The bounded
plate member is cut by the
bounding plate and sniped
as shown.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 276

 Member End Cuts

Flange-penetrated Top Cuts

All web cuts are available for both member assembly connections and generic assembly
connections.

Name Cross- Description Parameters

Sections
Supported

Flg Inside Hook All Valid boundaries and

Flange Relief orientations present a
Top face and a top edge to
the bounding member.
The bounding member is
still valid if it has a bottom
edge.

Flg Inside Hook All Valid boundaries and

Flange Relief orientations present a
Snipe Top WL face and a top edge to
the bounding member.
The bounding member is
still valid if it has a bottom
edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 277

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Flg Inside Hook All Valid boundaries and

Flange Relief orientations present a
Snipe Top FL face and a top edge to
the bounding member.
The bounding member is
still valid if it has a bottom
edge.

Flg Sqr Flange All Valid boundaries and

Relief Top orientations present a
face and a top edge to
the bounding member.
The bounding member is
still valid if it has a bottom
edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 278

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Flg Sqr Flg Rlf All with no Valid boundaries and

Outside Snp left flange orientations present a
Top WL face and a top edge to
the bounding member.
The bounding member is
still valid if it has a bottom
edge.

Flg Sqr Flg Rlf All with left Valid boundaries and
Outside Snp and right orientations present a
Top FL flanges face and a top edge to
the bounding member.
The bounding member is
still valid if it has a bottom
edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 279

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Flg Sqr Alg All Valid boundaries and

Flange Relief orientations present a
Top face and a top edge to
the bounding member.
The bounding member is
still valid if it has a bottom
edge.

Flg Sqr Alg Flg All with no Valid boundaries and

Rlf Outside left flange orientations present a
Snp Top WL face and a top edge to
the bounding member.
The bounding member is
still valid if it has a bottom
edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 280

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Flg Sqr Alg Flg All with left Valid boundaries and
Rlf Outside and right orientations present a
Snp Top FL flanges face and a top edge to
the bounding member.
The bounding member is
still valid if it has a bottom
edge.

Flg Edge Hook All Valid boundaries and

Flg Rlf OutSide orientations present a
Top face and a top edge to
the bounding member.
The bounding member is
still valid if it has a bottom
edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 281

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Flg Edge Hook All with no Valid boundaries and

Flg Rlf OutSide left flange orientations present a
Snp Top WL face and a top edge to
the bounding member.
The bounding member is
still valid if it has a bottom
edge.

Flg Edge Hook All with left Valid boundaries and

Flg Rlf OutSide and right orientations present a
Snp Top FL flanges face and a top edge to
the bounding member.
The bounding member is
still valid if it has a bottom
edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 282

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Flg Top Snipe All with no Valid boundaries and

Outside WL left flange orientations present a
face and a top edge to
the bounding member.
The bounding member is
still valid if it has a bottom
edge.

Flg Top Snipe All with left Valid boundaries and

Outside FL and right orientations present a
flanges face and a top edge to
the bounding member.
The bounding member is
still valid if it has a bottom
edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 283

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Flg Top Snipe All with no Valid boundaries and

Outside left flange orientations present a
Setback WL face and a top edge to
the bounding member.
The bounding member is
still valid if it has a bottom
edge.

Flg Top Snipe All with left Valid boundaries and

Outside and right orientations present a
Setback FL flanges face and a top edge to
the bounding member.
The bounding member is
still valid if it has a bottom
edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 284

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Flg Outside All with no Valid boundaries and

Snipe Top left flange orientations do not
Offset WL present a top edge to the
bounding member.

Flg Outside All with left Valid boundaries and

Snipe Top and right orientations do not
Offset FL flanges present a top edge to the
bounding member.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 285

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Flg Snipe Face All All

Relief Top

Flg Hook Face All All

Relief Top

Intergraph Smart® 3D 2D Symbols Reference Data Guide 286

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Flg Edge Hook All Valid boundaries and

Flange Relief orientations present a
Inside Top face and a bottom edge
to the bounding member.
The bounding member is
still valid if it has a top
edge.

Flg Top All Valid boundaries and

Outside Hook orientations present a
Flange Relief face and a bottom edge
to the bounding member.
The bounding member is
still valid if it has a top
edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 287

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Flg Top Snipe Standard Standard member is

OutSide member to bounded to a tubular
_Tube_FL Tube member. The bounded
member's left side flange
is cut.

Flg Top Snipe Standard Standard member is

OutSide member to bounded to a tubular
_Tube_WL Tube member. In this case, no
left side flange exists for
the bounded member, so
the web-left is used as a
reference.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 288

 Member End Cuts

Flange-penetrated Bottom Cuts

All web cuts are available for both member assembly connections and generic assembly
connections.

Name Cross- Description Parameters

Sections
Supported

Flg Inside Hook All Valid boundaries and

Flange Relief orientations present a
Bottom face and a bottom edge
to the bounding
member. The bounding
member is still valid if it
has a top edge.

Flg Inside Hook All Valid boundaries and

Flange Relief orientations present a
Snipe Bottom face and a bottom edge
to the bounding
member. The bounding
member is still valid if it
has a top edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 289

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Flg Sqr Flange All Valid boundaries and

Relief Bottom orientations present a
face and a bottom edge
to the bounding
member. The bounding
member is still valid if it
has a top edge.

Flg Sqr Flg Rlf All with no left Valid boundaries and
Outside Snp flange orientations present a
Bottom face and a bottom edge
to the bounding
member. The bounding
member is still valid if it
has a top edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 290

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Flg Sqr Alg All Valid boundaries and

Flange Relief orientations present a
Bottom face and a bottom edge
to the bounding
member. The bounding
member is still valid if it
has a top edge.

Flg Sqr Alg Flg All with no left Valid boundaries and
Rlf Outside flange orientations present a
Snp Bottom face and a bottom edge
to the bounding
member. The bounding
member is still valid if it
has a top edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 291

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Flg Edge Hook All Valid boundaries and

Flg Rlf OutSide orientations present a
Bottom face and a bottom edge
to the bounding
member. The bounding
member is still valid if it
has a top edge.

Flg Edge Hook All with no left Valid boundaries and

Flg Rlf OutSide flange orientations present a
Snp Bottom face and a bottom edge
to the bounding
member. The bounding
member is still valid if it
has a top edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 292

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Flg Bottom All with no left Valid boundaries and

Snipe Outside flange orientations present a
face and a bottom edge
to the bounding
member. The bounding
member is still valid if it
has a top edge.

Flg Bottom All with no left Valid boundaries and

Snipe Outside flange orientations present a
Setback face and a bottom edge
to the bounding
member. The bounding
member is still valid if it
has a top edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 293

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Flg Outside All with no left Valid boundaries and

Snipe Bottom flange orientations do not
Offset present a top edge to
the bounding member.

Flg Snipe Face All All

Relief Top

Intergraph Smart® 3D 2D Symbols Reference Data Guide 294

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Flg Hook Face All All

Relief Top

Flg Edge Hook All Valid boundaries and

Flange Relief orientations present a
Inside Bottom face and a top edge to
the bounding member.
The bounding member
is still valid if it has a
bottom edge.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 295

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Flg Bottom All Valid boundaries and

Outside Hook orientations present a
Flange Relief face and a top edge to
the bounding member.
The bounding member
is still valid if it has a
bottom edge.

FlgBottom Standard Standard member is

Snipe member to bounded to a tubular
OutSide_Tube_ Tube member. The right side
FR flange is cut as shown.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 296

 Member End Cuts

Flange Non-penetrated Cuts

There are separate web cuts for member assembly connections and generic assembly
connections.

Name Cross- Description Parameters

Sections
Supported

Straight_LR All with left

and right
(generic)
flanges

Axis_Flange_Flush_R All with no

left flange
(member)

Straight_R
(generic)

Axis_Flange_Straight_ All with left

Setback_LR and right
flanges
(member)

StraightSetback_LR
(generic)

Intergraph Smart® 3D 2D Symbols Reference Data Guide 297

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Axis_Flange_Straight_ All with no

Setback_R left flange
(member)

StraightSetback_R
(generic)

Axis_Flange_Sniped_ All with left

Setback_LR and right
flanges
(member)

Sniped_Setback_LR
(generic)

Intergraph Smart® 3D 2D Symbols Reference Data Guide 298

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Axis_Flange_Sniped_ All with no

Setback_R left flange
(member)

Sniped_Setback_R
(generic)

The following smart items are for cases in which the bounding member is a tube and
the bounded member is a standard member. These cases do not use the 8193 edge ID in the
symbol file.

Name Cross- Description Parameters

Sections
Supported

Axis_Flange_Straight_ All with left

Setback_Tube_LR and right
flanges.
(member)

Intergraph Smart® 3D 2D Symbols Reference Data Guide 299

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Axis_Flange_Straight_ All with no

Setback_Tube_R left flange.
(member)

Axis_Flange_Sniped_ All with left

Setback_Tube _LR and right
flanges.
(member)

Intergraph Smart® 3D 2D Symbols Reference Data Guide 300

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

Axis_Flange_Sniped_ All with no

Setback_Tube_R left flange.
(member)

Web Cuts for Split Members

Creates end-to-end web cuts for collinear members. End cuts are applied to both the bounded
and bounding members.
Different web cut shapes are possible by changing the answers to user-questions on the
Selection tab in the assembly connection Properties dialog box.

Name Cross- Description Parameters

Sections
Supported

MbrSplitWeb_NoA All A web cut is placed

ngle perpendicular to the
member axis at the
seam location.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 301

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

MbrSplitWeb_ All A web cut is placed at

AngleWebSqFl an offset towards
bounded and angular to
the member axis.
Flanges can have a
different seam angle.

MbrSplitWeb_ All A web cut is placed at

AngleWebSqFl_2 an offset towards
bounding and angular
to the member axis.
Flanges can have a
different seam angle.

MbrSplitWeb_ All A web cut is placed at

AngleWebBevelFl an offset towards
bounded and angular to
the member axis.
Flanges have a seam
angle equal to that of
the web.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 302

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

MbrSplitWeb_ All A web cut is placed at

AngleWebBevelFl an offset towards
_2 bounding and angular
to the member axis on
bounded. Flanges have
a seam angle equal to
that of the web.

MbrSplitWeb_ All A web cut is placed at

AngleWebAngleFl an offset towards
bounded and angular to
the member axis.
Flanges can have a
different seam angle.
The cutting plane is
inclined to the member
axis, and the angle of
the inclination can be
changed using the
cutVang parameter.

MbrSplitWeb_ All A web cut is placed at

AngleWebAngleFl an offset towards
_2 bounding and angular
to the member axis.
Flanges can have a
different seam angle.
The cutting plane is
inclined to the member
axis, and the angle of
the inclination can be
changed using the
cutVang parameter.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 303

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

MbrSplitWeb_ All A web cut is placed at

DistWebDistFl an offset towards
bounded, and slope is
controlled through
offsets at top and
bottom points of the
seam.

MbrSplitWeb_ All A web cut is placed at

DistWebDistFl_2 an offset towards
bounding, and the
slope is controlled
through offsets at top
and bottom points of
the seam.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 304

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

MbrSplitWeb_ All A web cut is placed at

OffsetWebOffsetFl an offset and angular to
the member axis on
bounded. The web, top,
and bottom flanges can
have different offsets
from the original seam.

MbrSplitWeb_ All A web cut is placed at

OffsetWebOffsetFl an offset and angular to
_2 the member axis on
bounded. The web, top,
and bottom flanges can
have different offsets
from the original seam.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 305

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

MbrSplitWeb_Tub Circular A cut is placed at the

e sections seam location.

Flange Cuts for Split Members

Placed on flanges of members connected end to end and collinear.
A flange cut is placed only when the answer for SplitEndToEndCase is NoAngle.

Name Cross- Description Parameters

Sections
Supported

MbrEndFlg_Straight All with left and Places a

_LR right flanges. straight cut.

MbrEndFlg_Straight All with no left Places a

_R flange. straight cut.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 306

 Member End Cuts

Mitered Web Cuts for Members

Name Cross- Description Parameters

Sections
Supported

MbrMiterWeb_S All Places a straight center

S cut and a sniped cut at
top and bottom so that
the flanges of bounding
and bounded do not
meet.

MbrMiterWeb_S All Places a straight cut and

B a sniped cut at bottom
so that the bottom
flanges of bounding and
bounded do not meet.

MbrMiterWeb_S All Places a straight cut and

T a sniped cut at top so
that the top flanges of
bounding and bounded
do not meet.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 307

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

MbrMiterWeb_T Circular Places a miter cut for

ube sections circular cross-sections.

Mitered Flange Cuts for Members

Name Cross- Description Parameters

Sections
Supported

MbrEndFlg_ All with left Places a miter cut on

StraightSetback_L and right the flange.
R flanges.

MbrEndFlg_ All with no left Places a miter sloped

StraightSetback_ flange. cut on the flange.
R

Intergraph Smart® 3D 2D Symbols Reference Data Guide 308

 Member End Cuts

Free-end Web Cuts for Members

These web cuts are placed at the end of an unsupported member.

Name Cross- Description Parameters

Sections
Supported

MbrWeb_FreeSnipeT All Places a sniped

op web cut with slope
inward at the top of
the flange.

MbrWeb_ All Places a sniped

FreeSnipeBottom web cut with slope
inward at the
bottom of the
flange.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 309

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

MbrWeb_FreeAngled All Use when

Cut EndcutType is
Welded in the
assembly
connection
Properties dialog
box.
Places a sniped
web cut. The
cutting plane
direction is inclined
towards the
member axis.

MbrTube_FreeEndCu Circular Places a sniped

t sections end cut for tubes.
The sketching
plane can be
rotated.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 310

 Member End Cuts

Free-end Flange Cuts for Members

These web cuts are placed at the end of an unsupported member.

Name Cross- Description Parameters

Sections
Supported

MbrFree_Flange_ All with left Places a straight flange

Straight_LR and right cut.
flanges

MbrFree_Flange_ All with no left Places a straight flange

Straight_R flange cut.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 311

 Member End Cuts

Name Cross- Description Parameters

Sections
Supported

MbrFree_Flange_ All with left Places a sniped flange

Sniped_LR and right cut.
flanges

MbrFree_Flange_ All with no left Places a sniped flange

Sniped_R flange cut.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 312

SECTION 14

Slots
Slot (also called penetration) symbols are delivered in the [Reference Data
Folder]\SharedContent\FTLibrary\Penetrations, [Reference Data
Folder]\SharedContent\MarineLibrary\Penetrations, and [Reference Data
Folder]\SharedContent\Penetrations folders.

In This Section
Style 1 ............................................................................................ 313
Slot C ............................................................................................. 314
Slot I ............................................................................................... 315

Style 1
The slot has three classes: Double, Single and Slit in Style1. You can select these classes when
the style is Style1.
The slot has two styles: Style1 and Style2.The default style is Style2. You can change to Style1
on the Properties dialog box.
The slot has a property named FlipSlot to determine whether to flip. The default value is No, but
you can change the value to Yes on the Properties dialog box.

Name Question: Allow clips Icon

SlotA5 No clip.
Symbol location:
\FTLIBRARY\Penetrations\Styl
e1\SlotA5.sym
Parameter rules:
SlotA5Param

SlotA5-1 Secondary\ None

Symbol location:
\FTLIBRARY\Penetrations\Styl
e1\SlotA5.sym
Parameter rules:
SlotA5Param

Intergraph Smart® 3D 2D Symbols Reference Data Guide 313

 Slots

Name Question: Allow clips Icon

Default\Primary
Collar ItemName:
Collar5-1
Symbol location:
\FTLIBRARY\Collars\Style1\
Collar5-1.sym
Parameter rules:
CollarParm

Slot C
Slot C class penetrations are connected to their cross-sections.

Name Selection Logic in the Parameters

Rules

SlotTC_T_PAA_STR Non-tight

Intergraph Smart® 3D 2D Symbols Reference Data Guide 314

 Slots

Slot I
Name Cross- Selection Logic Parameters
Sections in the Rules
Supported

SlotAI_LR_AAAA_STR EA Non-tight
UA Profile height >
125 mm

SlotBI_LR_PAAP_STR B Tight

Intergraph Smart® 3D 2D Symbols Reference Data Guide 315

 Slots

Name Cross- Selection Logic Parameters

Sections in the Rules
Supported

SlotBI_LR_AAAA_STR B Non-tight

SlotFI Available in
catalog, but not
available in
current selection
of SML Slot
rules.

Name Question Allow clips Icon

SlotA5-2 None\Secondary
Symbol location:
\FTLIBRARY\Penetrations\Style1\SlotA5.
sym
Parameter rules:
SlotA5Param

Intergraph Smart® 3D 2D Symbols Reference Data Guide 316

 Slots

Default\Primary Ordinary Special

Ordinary clip
Collar ItemName:
Collar5-2
Symbol location:
\FTLIBRARY\Collars\Style1\ Collar5-
2.sym
Parameter rules:
CollarBotParm
Special clip
Collar ItemName:
Collar5-2-S
Symbol location:
\FTLIBRARY\Collars\Style1\ Collar5-
1.sym
Parameter rules:
CollarParm

SlotA5-3 None
Symbol location:
\FTLIBRARY\Penetrations\Style1\SlotA5.
sym
Parameter rules:
SlotA5Param

Primary Ordinary Special

Intergraph Smart® 3D 2D Symbols Reference Data Guide 317

 Slots

Ordinary clip
Collar ItemName：
Collar-3
Symbol location:
\FTLIBRARY\Collars\Style1\ Collar-
3.sym
Parameter rules:
TopBotParm
Special clip
Collar ItemName：
Collar-3-S
Symbol location:
\FTLIBRARY\Collars\Style1\ Collar-
1.sym
Parameter rules:
CollarTopParm

Secondary Ordinary Special

Ordinary clip
Collar ItemName：
Collar5-2
Symbol location:
\FTLIBRARY\Collars\Style1\ Collar5-
2.sym
Parameter rules:
CollarBotParm
Special clip
Collar ItemName：
Collar5-2-S
Symbol location:
\FTLIBRARY\Collars\Style1\ Collar5-
1.sym
Parameter rules:
CollarParm

Intergraph Smart® 3D 2D Symbols Reference Data Guide 318

 Slots

Default

SlotA5-4 None
Symbol location:
\FTLIBRARY\Penetrations\Style1\SlotA5.
sym
Parameter rules:
SlotA5Param

Primary
Collar ItemName：
Collar-1
Symbol location:
\FTLIBRARY\Collars\Style1\ Collar-
1.sym
Parameter rules:
CollarTopParm

Secondary
Collar ItemName：
Collar5-1
Symbol location:
\FTLIBRARY\Collars\Style1\ Collar5-
1.sym
Parameter rules:
CollarParm

Default

Intergraph Smart® 3D 2D Symbols Reference Data Guide 319

 Slots

SlotA5- None
Free
Symbol location:
\FTLIBRARY\Penetrations\Style1\SlotA5.
sym
Parameter rules:
SlotA5Param

Primary Default clip Optional clip

Default clip
Collar ItemName：
Collar-3
Symbol location:
\FTLIBRARY\Collars\Style1\ Collar-
3.sym
Parameter rules:
CTopBotParm
Optional clip
Collar ItemName：
Collar-1
Symbol location:
\FTLIBRARY\Collars\Style1\ Collar-
1.sym
Parameter rules:
CollarTopParm

Secondary Default clip Optional clip

Intergraph Smart® 3D 2D Symbols Reference Data Guide 320

 Slots

Default clip
Collar ItemName：
Collar5-2
Symbol location:
\FTLIBRARY\Collars\Style1\ Collar5-
2.sym
Parameter rules:
CollarBotParm
Optional clip
Collar ItemName：
Collar5-1
Symbol location:
\FTLIBRARY\Collars\Style1\ Collar5-
1.sym
Parameter rules:
CollarParm

Default

SlotA6 No Collar
Symbol location:
\FTLIBRARY\Penetrations\Style1\SlotA6.
sym
Parameter rules:
SlotA6Param

Intergraph Smart® 3D 2D Symbols Reference Data Guide 321

 Slots

SlotA6-1 None\Secondary
Symbol location:
\FTLIBRARY\Penetrations\Style1\SlotA6.
sym
Parameter rules:
SlotA6Param

Primary\default
Collar ItemName：
Collar-1
Symbol location:
\FTLIBRARY\Collars\Style1\ Collar-
1.sym
Parameter rules:
CollarTopParm

SlotA6-3 None\Secondary
Symbol location:
\FTLIBRARY\Penetrations\Style1\SlotA6.
sym
Parameter rules:
SlotA6Param

Primary\Default Ordinary Special

Intergraph Smart® 3D 2D Symbols Reference Data Guide 322

 Slots

Ordinary
Collar ItemName：
Collar-3
Symbol location:
\FTLIBRARY\Collars\Style1\ Collar-
3.sym
Parameter rules:
CTopBotParm
Special
Collar ItemName：
Collar-3-S
Symbol location:
\FTLIBRARY\Collars\Style1\ Collar-
1.sym
Parameter rules:
CollarTopParm

SlotA-T3 None
Symbol location:
\FTLIBRARY\Penetrations\Style1\SlotA-
T3.sym
Parameter rules:
SlotAT3Param

Primary
Collar ItemName：
CollarA-T3
Symbol location:
\FTLIBRARY\Collars\Style1\ CollarA-
T3.sym
Parameter rules:
CollarParm

Intergraph Smart® 3D 2D Symbols Reference Data Guide 323

 Slots

Secondary
Collar ItemName：
CollarA-T3L
Symbol location:
\FTLIBRARY\Collars\Style1\ CollarA-
T3L.sym
Parameter rules:
CollarParm

Default

SlotB5 No clip
Symbol location:
\FTLIBRARY\Penetrations\Style1\
SlotB5.sym
Parameter rules:
SlotB5Param

SlotB5-1 None\Secondary
Symbol location:
\FTLIBRARY\Penetrations\Style1\
SlotB5.sym
Parameter rules:
SlotB5Param

Intergraph Smart® 3D 2D Symbols Reference Data Guide 324

 Slots

Default\Primary
Collar ItemName：
CollarB5-1
Symbol location:
\FTLIBRARY\Collars\Style1\ CollarB5-
1.sym
Parameter rules:
CollarParm

Intergraph Smart® 3D 2D Symbols Reference Data Guide 325

SECTION 15

Sketched Features
The sketched feature symbols are delivered with the software in the [Reference Data
Folder]\SharedContent\Sketched Features folder.

Name Description Parameters

Obround Feature Has no smart rule to

select.
Available when placing
an opening/Sketched
feature.

Oval Feature Has no smart rule to

select.
Available when placing
an opening/Sketched
feature.

Rectangle Feature Has no smart rule to

select.
Available when placing
an opening/Sketched
feature.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 326

 Sketched Features

Name Description Parameters

Round Feature Has no smart rule to

select.
Available when placing
an opening/Sketched
feature.

Square Feature Has no smart rule to

select.
Available when placing
an opening/Sketched
feature.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 327

SECTION 16

Openings
The opening symbols are delivered with the software in the [Reference Data Product
Folder]\SharedContent\Openings folder. You can create your own custom opening symbols
using the 2D Symbols utility that is delivered with the software.

In This Section
CircleOpening ................................................................................ 328
OvalOpening .................................................................................. 329
RectangleOpening ......................................................................... 329
SketchOpening .............................................................................. 329
SquareOpening.............................................................................. 330
TriangleOpening ............................................................................ 330

CircleOpening

Intergraph Smart® 3D 2D Symbols Reference Data Guide 328

 Openings

OvalOpening

RectangleOpening

SketchOpening

Intergraph Smart® 3D 2D Symbols Reference Data Guide 329

 Openings

SquareOpening

TriangleOpening

Intergraph Smart® 3D 2D Symbols Reference Data Guide 330

SECTION 17

Structural Manufacturing
The structural manufacturing symbols are delivered with the software in the [Reference Data
Product Folder]\SharedContent\StructManufacturing folder. You can create your own custom
symbols using the 2D Symbols utility that is delivered with the software.

In This Section
Manufacturing Requirements for Profile Cross Sections............... 332
Manufacturing Requirements for Member Cross Sections............ 333
Bevel .............................................................................................. 334
Bevel1 (I-Type) .............................................................................. 334
Bevel2 (V-Type) ............................................................................. 335
Bevel3 (V-Type) ............................................................................. 335
Bevel4 (X-Type) ............................................................................. 335
Bevel5 (Y-Type) ............................................................................. 335
Bevel6 (X-Type with Chamfer) ...................................................... 335
Bevel7 (X-Type with Chamfer) ...................................................... 336
Bevel8 (X-Type with Chamfer) ...................................................... 336
Bevel9 (X-Type with Chamfer) ...................................................... 336
Bevel10 .......................................................................................... 336
BevelA ........................................................................................... 337
BevelB ........................................................................................... 337
BevelParam ................................................................................... 338
FeatureTab1 .................................................................................. 338
Grind .............................................................................................. 338
Knuckle .......................................................................................... 339
Margin ............................................................................................ 339
PartCenterLL ................................................................................. 339
PartDirC ......................................................................................... 340
PartDirCL ....................................................................................... 340
PartDirCR ...................................................................................... 340
PartDirL .......................................................................................... 341
PartDirLL ........................................................................................ 341
PartDirLLFlangeRR ....................................................................... 341
PartDirR ......................................................................................... 342
PartDirRR ...................................................................................... 342
PartDirRRFlangeLL ....................................................................... 342
PMFeature ..................................................................................... 343
Shrinkage ....................................................................................... 343
SMPlateTab ................................................................................... 343
UnSpecBevel ................................................................................. 344
WeldTab1 ...................................................................................... 344

Intergraph Smart® 3D 2D Symbols Reference Data Guide 331

 Structural Manufacturing

Manufacturing Requirements for Profile Cross

Sections
All profile cross sections must support the IJUAXSectionMfgProperties and
IJUAXSectionMatlProperties virtual interfaces.

IJUAXSectionMatlProperties …
ShearCenterLoc_X
ShearCenterLoc_Y
CentroidLoc_X
CentroidLoc_Y

IJUAXSectionMfgProperties OriginKeyPoint
XDirectionKeyPoint
YDirectionKeyPoint

The Shear Center is the point at which a shear force can act without producing any twist in the
section. The centroid of a cross section shape is the arithmetic mean (average) position of all
the points in the shape.
Shear Center and Centroid are both required properties to unfold a profile part in Structural
Manufacturing. Shear Center gives the axis information about which the profile is untwisted. The
Centroid gives the axis about which the profile is unbent.
OriginKeyPoint, XDirectionKeyPoint and YDirectionKeyPoint values are used only in Structural
Manufacturing to interpret the location of Centroid and Shear Center. Centroid and Shear Center
locations should be given correctly relative to these key points.
The following example shows how to define a cross section centroid with respect to key points
defined in Cross Section work sheet:

Any of the following rows are correct for the previous figure:

Intergraph Smart® 3D 2D Symbols Reference Data Guide 332

 Structural Manufacturing

OriginKeyPoint XDirectionKeyPoint YDirectionKeyPoint Centroid_X Centroid_Y

1 23 13 15 75

13 15 1 15 25

23 15 1 75 35

Manufacturing Requirements for Member Cross

Sections
All member cross sections must have CrossSectionType information.
Valid Cross Section Type strings:
 BulbFlat
 Channel
 FlatBar
 IBar
 TeeBar
 EqualAngle
 UnequalAngle
 RectangleTube
 SquareTube
 RoundTube
 RoundBar
 SquareBar
 HalfRound.

Intergraph Smart® 3D 2D Symbols Reference Data Guide 333

 Structural Manufacturing

Member cross sections are not required to support IJUAXSectionMfgProperties or

IJUAXSectionMatlProperties virtual interfaces.
Cardinal Point 10 must be defined in the member cross section symbol at the centroid location.
Cardinal Point 15 must be defined at the Shear Center location.
If the member has a flange, it must support the IStructFlangedSectionDimensions virtual
interface with the following properties:
 d = Web Depth
 tw = Web Thickness
 tf = Flange Thickness
 bf = Flange Width
If the member, such as round tubes, rectangular tubes, Half Round, and so on, does not have a
flange, it must support the IStructCrossSectionDimensions virtual interface.
 Depth = Web Depth
 tdes = Thickness
OR
 tnom = Thickness
This property is read-only if the tdes property does not exist.

Bevel

See Also
Structural Manufacturing (on page 331)

Bevel1 (I-Type)

Intergraph Smart® 3D 2D Symbols Reference Data Guide 334

 Structural Manufacturing

Bevel2 (V-Type)

Bevel3 (V-Type)

Bevel4 (X-Type)

Bevel5 (Y-Type)

Bevel6 (X-Type with Chamfer)

Intergraph Smart® 3D 2D Symbols Reference Data Guide 335

 Structural Manufacturing

Bevel7 (X-Type with Chamfer)

Bevel8 (X-Type with Chamfer)

Bevel9 (X-Type with Chamfer)

Bevel10

Intergraph Smart® 3D 2D Symbols Reference Data Guide 336

 Structural Manufacturing

BevelA

See Also
Structural Manufacturing (on page 331)

BevelB

See Also
Structural Manufacturing (on page 331)

Intergraph Smart® 3D 2D Symbols Reference Data Guide 337

 Structural Manufacturing

BevelParam

FeatureTab1

See Also
Structural Manufacturing (on page 331)

Grind

See Also
Structural Manufacturing (on page 331)

Intergraph Smart® 3D 2D Symbols Reference Data Guide 338

 Structural Manufacturing

Knuckle

See Also
Structural Manufacturing (on page 331)

Margin

See Also
Structural Manufacturing (on page 331)

PartCenterLL

Intergraph Smart® 3D 2D Symbols Reference Data Guide 339

 Structural Manufacturing

PartDirC

PartDirCL

PartDirCR

Intergraph Smart® 3D 2D Symbols Reference Data Guide 340

 Structural Manufacturing

PartDirL

See Also
Structural Manufacturing (on page 331)

PartDirLL

See Also
Structural Manufacturing (on page 331)

PartDirLLFlangeRR

Intergraph Smart® 3D 2D Symbols Reference Data Guide 341

 Structural Manufacturing

PartDirR

See Also
Structural Manufacturing (on page 331)

PartDirRR

See Also
Structural Manufacturing (on page 331)

PartDirRRFlangeLL

See Also
Structural Manufacturing (on page 331)

Intergraph Smart® 3D 2D Symbols Reference Data Guide 342

 Structural Manufacturing

PMFeature

Shrinkage

SMPlateTab

See Also
Structural Manufacturing (on page 331)

Intergraph Smart® 3D 2D Symbols Reference Data Guide 343

 Structural Manufacturing

UnSpecBevel

WeldTab1

Intergraph Smart® 3D 2D Symbols Reference Data Guide 344

Index

2 C
2D Symbols Reference Data • 9 Chamfers • 24
2S Brackets • 10 CircleOpening • 328
2S Integrated Brackets • 13 Collars and Clips • 26
Corner Features for Members • 49
3 Corner Features for Plates and Stiffeners •
39
3S Brackets • 14 Cross Section Symbol 2L • 56
3S Flanged Brackets • 18 Cross Section Symbol B • 165
Cross Section Symbol BUBoxFM • 59
4 Cross Section Symbol BUC • 62
4S Brackets • 20 Cross Section Symbol BUCan • 65
Cross Section Symbol BUCone • 68
Cross Section Symbol BUEndCan • 70
5 Cross Section Symbol BUFlat • 72
5S Brackets • 21 Cross Section Symbol BUI • 75
Cross Section Symbol BUIHaunch • 77
A Cross Section Symbol BUITaperWeb • 80
Along-Axis Flange Cuts for Members • 273 Cross Section Symbol BUIUE • 83
Along-Axis Web Cuts for Members • 250 Cross Section Symbol BUL • 86
Cross Section Symbol BUL2 • 166
Cross Section Symbol BUL3 • 168
B Cross Section Symbol BUT • 89, 171
Bevel • 334 Cross Section Symbol BUTube • 91
Bevel1 (I-Type) • 334 Cross Section Symbol C (MC) • 93
Bevel10 • 336 Cross Section Symbol C_SS • 172
Bevel2 (V-Type) • 335 Cross Section Symbol C_SType • 174
Bevel3 (V-Type) • 335 Cross Section Symbol CS • 96
Bevel4 (X-Type) • 335 Cross Section Symbol EA • 176
Bevel5 (Y-Type) • 335 Cross Section Symbol FB • 178
Bevel6 (X-Type with Chamfer) • 335 Cross Section Symbol HalfR • 181
Bevel7 (X-Type with Chamfer) • 336 Cross Section Symbol HSSC (Pipe) • 98
Bevel8 (X-Type with Chamfer) • 336 Cross Section Symbol HSSCs • 100
Bevel9 (X-Type with Chamfer) • 336 Cross Section Symbol HSSR • 103
BevelA • 337 Cross Section Symbol HSSRs • 105
BevelB • 337 Cross Section Symbol HW • 108, 145
BevelParam • 338 Cross Section Symbol HWWF • 110, 147
Bounded by Plate ER • 248 Cross Section Symbol I • 183
Bounded Section Type Cross Section Symbol I_SType • 185
BUT, BUTL2 • 215 Cross Section Symbol L • 112
FB • 225 Cross Section Symbol P • 187
Bounded with Plate or Profile Web • 201 Cross Section Symbol R • 189
Bounded with Profile Top (Tripping Case) • Cross Section Symbol Rect • 116, 149
229 Cross Section Symbol RectC • 118, 151
Bracket Symbols • 10 Cross Section Symbol RectCWF • 120, 154
Cross Section Symbol RectWF • 123, 156
Cross Section Symbol RS • 125

Intergraph Smart® 3D 2D Symbols Reference Data Guide 345

 Index

Cross Section Symbol S • 127 Margin • 339

Cross Section Symbol SB • 191 Member Cross Sections • 54
Cross Section Symbol SqTu • 193 Member End Cuts • 250
Cross Section Symbol ST • 130 Miter End Cuts • 247
Cross Section Symbol T • 194 Mitered Flange Cuts for Members • 308
Cross Section Symbol T (MT) • 133 Mitered Web Cuts for Members • 307
Cross Section Symbol T_SType • 194
Cross Section Symbol UA • 197 N
Cross Section Symbol W (M) • 135
Cross Section Symbol Wedge • 138, 159 Non-Tight Clips • 26
Cross Section Symbol WedgeWF • 141,
161 O
Cut Back End Cuts • 236 Openings • 328
Optional Flange Cut Shapes • 248
D OvalOpening • 329
Double Sided Style1 Chamfer • 24
P
E PartCenterLL • 339
Edge Features • 200 PartDirC • 340
Edge Reinforcement End Cuts • 231 PartDirCL • 340
End-to-End End Cuts • 237 PartDirCR • 340
PartDirL • 341
PartDirLL • 341
F PartDirLLFlangeRR • 341
FeatureTab1 • 338 PartDirR • 342
Flange Contours for Brackets • 23 PartDirRR • 342
Flange Cuts for Split Members • 306 PartDirRRFlangeLL • 342
Flange Non-penetrated Cuts • 297 PMFeature • 343
Flange-penetrated Bottom Cuts • 289 Preface • 8
Flange-penetrated Center Cuts • 273 Profile Cross Sections • 164
Flange-penetrated Top Cuts • 277 Profile End Cuts • 201
Free End • 229
Free-end Flange Cuts for Members • 311 R
Free-end Web Cuts for Members • 309
RectangleOpening • 329
G
S
Grind • 338
Shrinkage • 343
Single Sided Style 1 Chamfers • 25
K Sketched Features • 326
Knuckle • 339 SketchOpening • 329
Slot C • 314
L Slot I • 315
Slots • 313
Long Box End Cuts • 246 SMPlateTab • 343
Snip End Cuts • 232
M SquareOpening • 330
Manufacturing Requirements for Member Standard Bracket Flange Contour • 23
Cross Sections • 333 Structural Manufacturing • 331
Manufacturing Requirements for Profile Style 1 • 313
Cross Sections • 332

Intergraph Smart® 3D 2D Symbols Reference Data Guide 346

 Index

T
Tight Collars • 30
TriangleOpening • 330

U
UnSpecBevel • 344

W
Wall Cross Sections • 144
Web Cuts for Split Members • 301
Web Non-penetrated Cuts • 271
Web-penetrated Bottom Cuts • 264
Web-penetrated Center Cuts • 251
Web-penetrated Top Cuts • 257
Weld and Clip End Cuts • 201
WeldTab1 • 344
What's New in 2D Symbols Reference Data
•8

Intergraph Smart® 3D 2D Symbols Reference Data Guide 347