Arduion

Experiment work
 1 – Test Arduino
This project will test your Arduino by
blinking an LED that is connected
directly to the board.

Parts Needed
(1) Arduino Uno
(1) USB A-to-B Cable
(1) LED 5mm
(1) 220 Ω Resistor

Project Diagram
Program code

 void setup()
{
pinMode(13, OUTPUT);
}

void loop()
{
digitalWrite(13, HIGH); // Turn on the LED
delay(1000); // Wait for one second
digitalWrite(13, LOW); // Turn off the LED
delay(1000); // Wait for one second
}
 2 -Flash
void setup() {
// initialize digital pin 11 as an output.
pinMode(11, OUTPUT);
}

// the loop function runs over and over again forever

void loop() {
digitalWrite(11, HIGH); // turn the LED on
delay(1000); // wait for a second
digitalWrite(11, LOW); // turn the LED off
delay(1000); // wait for a second
}
Flash

Try to change the

Delay and Pin
 3-10 Led shift flash
void setup() {
// initialize digital pin 11 as an output.
pinMode(4, OUTPUT);
pinMode(5, OUTPUT);
pinMode(6, OUTPUT);
pinMode(7, OUTPUT);
pinMode(8, OUTPUT);
pinMode(9, OUTPUT);
pinMode(10, OUTPUT);
pinMode(11, OUTPUT);
pinMode(12, OUTPUT);
pinMode(13, OUTPUT);
}
// the loop function runs over and over again forever

digitalWrite(8, LOW);
void loop() {
digitalWrite(9, HIGH);
digitalWrite(4, HIGH); delay(1000);
delay(1000);

digitalWrite(9, LOW);
digitalWrite(4, LOW); digitalWrite(10, HIGH);
digitalWrite(5, HIGH); delay(1000);
delay(1000);
digitalWrite(10, LOW);
digitalWrite(5, LOW); digitalWrite(11, HIGH);
digitalWrite(6, HIGH);
delay(1000);
delay(1000);
digitalWrite(11, LOW);
digitalWrite(6, LOW);
digitalWrite(12, HIGH);
delay(1000);
digitalWrite(7, HIGH);
delay(1000);
digitalWrite(12, LOW);
digitalWrite(13, HIGH);
digitalWrite(7, LOW); delay(1000);
digitalWrite(8, HIGH);
delay(1000);
digitalWrite(13, LOW);
}
 Using For command
void setup() {
// initialize digital pin 11 as an output.
pinMode(3, OUTPUT);
pinMode(4, OUTPUT);
pinMode(5, OUTPUT);
pinMode(6, OUTPUT);
pinMode(7, OUTPUT);
pinMode(8, OUTPUT);
pinMode(9, OUTPUT);
pinMode(10, OUTPUT);
pinMode(11, OUTPUT);
pinMode(12, OUTPUT);
pinMode(13, OUTPUT);
}
// the loop function runs over and over again
forever
void loop() {
for (I=4;I<=13;I++) {
digitalWrite(I, HIGH);
delay(1000);
digitalWrite(I, LOW);
}
}
10 Led shift flash
with different delay
Try to change the
Delay by reading
Potentiometer
 4-Traffic Light
void setup() {
// initialize digital pin 11 as an output.

pinMode(8, OUTPUT);
pinMode(9, OUTPUT);
pinMode(10, OUTPUT);
}
// the loop function runs over and over again
forever
void loop() {

digitalWrite(8, HIGH);
delay(70000);
digitalWrite(8, LOW);
digitalWrite(9, HIGH);
delay(15000);
digitalWrite(9, LOW);
digitalWrite(10, HIGH);
delay(150000);
digitalWrite(10, LOW);
}
Traffic Light
 Modify the program to control
traffic light in the illustrated
circuit
Traffic Light for Square

Write a program to control

a traffic light for a square

Direction Direction Time

1 2 (Sec)
Red 1 Green 2 75
Red 1 Yello 2 15
Green 1 Red 2 75
Yellow 1 Red 2 15
5 – Push Button
Using a push button switch, you will be able to turn on and off
an LED.

Parts Needed
(1) Arduino Uno
(1) USB A-to-B Cable
(1) Breadboard – Half Size
(1) LED 5mm
(1) 220 Ω Resistor
(1) 10K Ω Resistor
(1) Push Button Switch
(6) Jumper Wires
Program code
void setup() {
pinMode(ledPin, OUTPUT); // initialize the LED pin as an output:
pinMode(buttonPin, INPUT); // initialize the pushbutton pin as an
input:
}

void loop() {
buttonState = digitalRead(buttonPin); // read the state of the
pushbutton value:

if (buttonState == HIGH) { // check if the pushbutton is pressed.

// if it is, the buttonState is HIGH:
digitalWrite(ledPin, HIGH); // turn LED on:
}
else {
digitalWrite(ledPin, LOW); // turn LED off:
 6 – Potentiometer
Using a potentiometer, you will be able to control the resistance of
an LED. Turning the knob will increase and decrease the frequency
the LED blinks.

Parts Needed
(1) Arduino Uno
(1) USB A-to-B Cable
(1) Breadboard – Half Size
(1) LED 5mm
(1) 220 Ω Resistor
(1) Potentiometer (10k Trimpot)
(6) Jumper Wires
Program code
void setup() {
// declare the ledPin as an OUTPUT:
pinMode(ledPin, OUTPUT);
}

void loop() {
// read the value from the sensor:
sensorValue = analogRead(sensorPin);
// turn the ledPin on
digitalWrite(ledPin, HIGH);
// stop the program for <sensorValue> milliseconds:
delay(sensorValue);
// turn the ledPin off:
digitalWrite(ledPin, LOW);
// stop the program for for <sensorValue> milliseconds:
delay(sensorValue);
}
 7 – RGB LED
This project will be using an RGB LED to
scroll through a variety of colors. RGB
stands for Red, Green and Blue and this
LED has the ability to create nearly
unlimited color combinations.
Parts Needed
(1) Arduino Uno
(1) USB A-to-B Cable
(1) Breadboard – Half Size
(1) RGB LED
(3) 330 Ω Resistor
(5) Jumper Wires
const int RED_PIN = 9;
const int GREEN_PIN = 10;
const int BLUE_PIN = 11;

void setup()
{ //Configure the Arduino pins to be outputs to drive the LEDs
pinMode(RED_PIN, OUTPUT);
pinMode(GREEN_PIN, OUTPUT);
pinMode(BLUE_PIN, OUTPUT);
}
void loop()
{
// LED is Red
digitalWrite(RED_PIN, HIGH);
digitalWrite(GREEN_PIN, LOW);
digitalWrite(BLUE_PIN, LOW);
delay(DISPLAY_TIME);
// LED is Green
digitalWrite(RED_PIN, LOW );
digitalWrite(GREEN_PIN, HIGH);
digitalWrite(BLUE_PIN, LOW);
delay(DISPLAY_TIME);
.
.
.
}
 8 – Scrolling LED
This project will blink 6 LEDs, one at a time, in a up and down formation.

Parts Needed
(1) Arduino Uno
(1) USB A-to-B Cable
(1) Breadboard – Half Size
(6) LED 5mm
(6) 220 Ω Resistor
(7) Jumper Wires
9 – Bar Graph
Problem
Using a potentiometer, you
can control a series of LEDs in
a column. Turning the
potentiometer knob will turn
on or off more of the LEDs.
Parts Needed
(1) Arduino Uno
(1) USB A-to-B Cable
(1) Breadboard – Half Size
(1) Potentiometer – Rotary
(10) LED 5mm
(10) 220 Ω Resistor
(11) Jumper Wires
10 – Multiple LEDs
Problem
This project will use 8 pins on the
Arduino board to blink 8 LEDs at the
same time.
Parts Needed
(1) Arduino Uno
(1) USB A-to-B Cable
(1) Breadboard – Half Size
(8) LED 5mm
(8) 330 Ω Resistor
(9) Jumper Wires