LTE X2 Handover (Successful Handover)

LTE Mobile eNodeB Network Core Network EventStudio System Designer 6

UE Target eNodeB Source MME SGW PGW
eNodeB 20-Apr-13 22:03 (Page 1)

This sequence diagram was generated with EventStudio Sytem Designer - http://www.EventHelix.com/EventStudio/

eNodeBs in LTE are interconnected with the X2 interface. If two eNodeBs are served by the same MME, handover from the
source to the target eNodeB will take place over the X2 interface.

Before the handover

RRC-Connected The UE and Source eNodeB
are in RRC Connected state.
Downlink data flow before handover

Downlink data is flowing from the SGW to the UE via the Source eNodeB.
Downlink Data
Downlink Data
s1_teid_dl1 s1_teid_dl1

Downlink Data

Uplink data flow before handover

Uplink data is flowing from the UE to the SGW via the Source eNodeB.
Uplink Data
Uplink Data
s1_teid_ul1 s1_teid_ul1

Uplink Data

Handover preparation
RRC Measurement Control The network sets the
rrc rrc measurement thresholds for
sending measurement reports.
RRC Measurement Report Neighboring cell signal quality
rrc rrc is now better than the serving
cell.
Signal strength of serving cell,
Signal strength of neighbors

RRC: Handover needs to be The RRC uses the latest

performed. A cell is selected for measurement to decide if a
handover. handover is needed to another
cell. The target cell is selected.
The eNodeB for the target cell
is identified.
Derive KeNB*
LTE X2 Handover (Successful Handover)
LTE Mobile eNodeB Network Core Network EventStudio System Designer 6
UE Target eNodeB Source MME SGW PGW
eNodeB 20-Apr-13 22:03 (Page 2)

X2AP Handover Request The Source eNodeB initiates

x2ap x2ap the handover with the
Handover Request message.
ECGI of the Target Cell
(of Target eNB), Information about active
UE-AMBR,
UE Security Capability,
E-RABs, security keys is
KeNB*, included in the message. (Click
E-RAB to be setup
(E-RAB ID, QCI, ARP, S1 on the message name above
S-GW TEID the arrow to see message
details)
Generate AS keys from KeNB
(KeNB = KeNB*)

Uplink S1 Bearer Establishment GTP connect for the uplink side

s1_teid_ul2 s1_teid_ul2 is established between the
Target eNodeB and the serving
SGW.
Perform admission control the Check if resources are
E-RABs in the message available at the target eNodeB
to accept this session.
Create DRB ID (Uplink / Assign Dedicated Radio Bearer
Downlink) ids for Uplink and Downlink.
RRC: Reserve downlink and The Target eNodeB allocates
uplink radio resources for the radio resources for the UE that
session will be handed in.
allocate The Target eNodeB allocates a
RACH Preamble RACH preamble to the UE. The
UE will use this preamble to
send a contention free RACH.
allocate A new C-RNTI is assigned to
C-RNTI the UE.

RRC: Prepare the Handover This message includes the

Command message (RRC RACH preamble that needs to
Connection Reconfiguration be sent to the terminal. This
Request)
message includes information
about the assigned radio
resources.
X2AP Handover Request Acknowledge The Target eNodeB responds
x2ap x2ap back to the source eNodeB with
a Handover Request
E-RAB ID,
Target X2 eNB TEID, Acknowledge message. This
Transparent container =
Handover Command
message carries the Handover
Command message (RRC
Connection Reconfiguration
Request) in a transparent
container. (Click on the
message name above the
arrow to see message details)
X2 Bearer Esablishment An X2 GTP connection is
x2_teid x2_teid established between the
Source and the Target
eNodeBs. This channel will
carry the user data during the
handover.
begin At this point, the UE is ready to
Buffering downlink data buffer downlink data that will be
received during the handover.

Handover execution
LTE X2 Handover (Successful Handover)
LTE Mobile eNodeB Network Core Network EventStudio System Designer 6
UE Target eNodeB Source MME SGW PGW
eNodeB 20-Apr-13 22:03 (Page 3)

RRC Connection Reconfiguration Request The Source eNodeB sends a

rrc rrc handover command to the UE.
The message contains a new
RACH Preamble Assignment,
Target C-RNTI, C-RNTI and new DRB IDs. A
Target DRB ID (UL/DL),
Target eNB AS Security Algorithm
RACH preamble is also
included for contention free
RACH access.
X2AP SN Transfer Status The PDCP sequence numbers
x2ap x2ap are sent from the source to the
target eNodeB. (Click on the
Downlink PDCP
Sequence Number, message name above the
Uplink PDCP Sequence
Number
arrow to see message details)

Downlink data flow during handover preparation

At this point all downlink data is getting rerouted from the source eNodeB to the
target eNode. The data is being buffered at the target as the UE is yet to connect
to the target.
Downlink Data
Downlink Data
s1_teid_dl1 s1_teid_dl1

Downlink Data
x2_teid x2_teid

Buffer the received downlink

data

Uplink data flow during handover preparation

The uplink data is still being sent from the UE to the SGW via the Source eNodeB.
Uplink Data
Uplink Data
s1_teid_ul1 s1_teid_ul1

Uplink Data

begin Meanwhile, the UE has

Switching to Target received the handover
eNodeB command and it is switching to
the new target cell.
Detach from Source
eNodeB

Generates KeNB (KeNB

= KeNB*) and AS keys

RRC-Idle At this point, the UE has

detached from the source
eNodeB but is still not
communicating with the target
eNodeB. The UE is in the
RRC-Idle state.
Synchronizing with target cell
RACH Preamble UE uses the preamble
rrc rrc assigned in the handover
command to send a RACH to
the target eNodeB.
 LTE X2 Handover (Successful Handover)
LTE Mobile eNodeB Network Core Network EventStudio System Designer 6
UE Target eNodeB Source MME SGW PGW
eNodeB 20-Apr-13 22:03 (Page 4)

Random Access Response The target eNodeB accepts the

rrc rrc request and responds back with
a timing adjustment and an
Timing Advance,
Target C-RNTI, uplink resource grant.
Uplink grant

RRC Connection Reconfiguration Complete The UE uses the assigned

rrc rrc resources to transmit the
Handover Confirm message
Target C-RNTI
(RRC Connection
Reconfiguration Complete).
end
Switching to Target
eNodeB

AS layer security procedure

RRC-Connected The UE is not connected to the

Target eNodeB. Thus it
transitions to the
RRC-Connected state.
Transmit transmission of queued
downlink data

The UE is now connected to the

target eNodeB. All the queued
messages are now transmitted
towards the UE.
Downlink Data
Downlink Data
Downlink Data

Downlink data flow during handover execution

During handover execution the data being routed from the SGW to the UE via the source
and the target eNodeBs.
Downlink Data
Downlink Data
s1_teid_dl1 s1_teid_dl1

Downlink Data
x2_teid x2_teid

Downlink Data

Uplink data flow during handover execution

The uplink data is now being transmitted from the UE to the SGW via the target eNodeB.
Uplink Data
Uplink Data
s1_teid_ul2 s1_teid_ul2

Uplink Data
LTE X2 Handover (Successful Handover)
LTE Mobile eNodeB Network Core Network EventStudio System Designer 6
UE Target eNodeB Source MME SGW PGW
eNodeB 20-Apr-13 22:03 (Page 5)

Handover completion

Switching path

At this point, the UE is receiving and transmitting data. The downlink data transmission
towards the terminal is still being routed via the source eNodeB. The path will now be
switched to remove the source eNodeB from the path.
S1AP Path Switch Request The target eNodeB requests
ECGI, the MME to switch the path
TAI,
UE Security Capability,
from the source eNodeB to the
E-RAB to be switched in DL (E-RAB ID, S1 Target eNB TEID) target eNodeB. (Click on the
message name above the
arrow to see message details)
Modify Bearer Request MME requests the SGW to
EPS Bearer in DL (EPS Bearer ID, S1 switch the path to the target
Target eNB TEID),
ECGI,
eNodeB.
TAI

Modify Bearer Request The SGW asks the PGW to

EPS Bearer ID, switch the path.
ECGI,
TAI

Modify Bearer Response

EPS Bearer ID

Modify Bearer Response The SGW responds back to the

EPS Bearer in DL (EPS Bearer ID) MME signaling the completion
of the path switch.
Send end marker

The SGW also inserts an end marker towards the source eNodeB. This
marker will be used to sequence the data received from the source
eNodeB and the new data received from the target eNodeB.
End Marker
s1_teid_dl1 s1_teid_dl1

End Marker
x2_teid x2_teid

Keep receiving the data from The target eNodeB will buffer
the source eNodeB until the data directly received from the
end marker is received SGW until all the data received
via the source eNodeB has
been transmitted. This is
needed to maintain the
transmission order.
Downlink data flow after handover
Downlink Data
Downlink Data SGW is now sending the data
s1_teid_dl2 s1_teid_dl2 using the target eNodeB TEID.

Downlink Data
LTE X2 Handover (Successful Handover)
LTE Mobile eNodeB Network Core Network EventStudio System Designer 6
UE Target eNodeB Source MME SGW PGW
eNodeB 20-Apr-13 22:03 (Page 6)

S1AP Path Switch Request Ack MME responds back to signal

E-RAB to be switched in UL (E-RAB ID) the completion of the path
swiitch. (Click on the message
name above the arrow to see
message details)
X2AP UE Context Release The end marker has been
x2ap x2ap received at the Target eNodeB.
At this point the target asks the
source eNodeB to release
resources for the UE. (Click on
the message name above the
arrow to see message details)
Delete UE Context

This sequence diagram was generated with EventStudio Sytem Designer - http://www.EventHelix.com/EventStudio/