Front Wiper and Washer

From Power Source System (See Page 62)

20A 25A
WASHER WIPER

3 1B 5 1E 2 1B

L- W

LG

B
1
C14
F14
Combination SW
M Front Washer
Motor
Wiper Relay
INT TIME

2
Washer
HIGH
LOW
OFF

INT

1
11 V W
IK3

2 W- B

LG

10
16 G
IC2

9
7 B
IC2

11
8 L
IC2
LG

17 LG
R

L
W- B

4 1 2 3
Front Wiper and Washer SW

5 4C
Front Wiper Motor

M
6 4M
W- B

F6

4 1E
5
8
W- B
1B

14 1D
W- B

IA

220
2005 HIGHLANDER (EWD592U)
 System Outline
With the ignition SW turned on, the current flows to TERMINAL 17 of the front wiper and washer SW, TERMINAL 2 of the
front wiper motor through the WIPER fuse, the current flows to TERMINAL 1 of the washer motor through WASHER fuse.
1. Low Speed Position
With the wiper SW turned to LOW position, the current flows through TERMINAL 17 of the front wiper and washer SW to
TERMINAL 7 to TERMINAL 1 of the front wiper motor to TERMINAL 5 to GROUND and causes the wiper motor to run at low
speed.
2. High Speed Position
With the wiper SW turned to HIGH position, the current flows through TERMINAL 17 of the front wiper and washer SW to
TERMINAL 8 to TERMINAL 4 of the front wiper motor to TERMINAL 5 to GROUND and causes the wiper motor to run at
high speed.
3. INT Position
With the wiper SW turned to INT position, the relay operates and the current which is connected by relay function flows
through TERMINAL 17 of the front wiper and washer SW to TERMINAL 2 to GROUND. This flow of current operates the
intermittent circuit and the current flows through TERMINAL 17 of the front wiper and washer SW to TERMINAL 7 to
TERMINAL 1 of the front wiper motor to TERMINAL 5 to GROUND and the wiper functions.
The intermittent operation is controlled by a condenser’s charged and discharged function installed in the relay and the
intermittent time is controlled by a time control SW to charge the charging time of condenser.
4. Washer Continuous Operation
With the washer SW pulled to on, the current flows through TERMINAL 1 of the washer motor to TERMINAL 2 to TERMINAL
11 of the front wiper and washer SW to TERMINAL 2 to GROUND and causes the washer motor to run and the window
washer to jet. This causes the current to flow to washer continuous operation circuit in TERMINAL 17 of the front wiper and
washer SW to TERMINAL 7 to TERMINAL 1 of the front wiper motor to TERMINAL 5 to GROUND and the wiper functions.

Service Hints
C14 Combination SW
2-Ground : Always continuity
17-Ground : Approx. 12 volts with the ignition SW at ON position
7-Ground : Approx. 12 volts with the front wiper and washer SW at LOW position
Approx. 12 volts 2 to 11 seconds intermittently with the front wiper and washer SW at INT position
16-Ground : Approx. 12 volts with the ignition SW on unless the front wiper motor at STOP position
8-Ground : Approx. 12 volts with the front wiper and washer SW at HIGH position
F6 Front Wiper Motor
2-3 : Closed unless the front wiper motor at STOP position

: PARTS LOCATION
Code See Page Code See Page Code See Page
C14 42 F6 40 (2AZ-FE) F14 40 (2AZ-FE)
F6 38 (3MZ-FE) F14 38 (3MZ-FE)
,,,
,,,
,,,
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR

Code See Page Junction Block and Wire Harness (Connector Location)
1B 29 Engine Room Main Wire and Instrument Panel J/B (Lower Finish Panel)
1D
29 Cowl Wire and Instrument Panel J/B (Lower Finish Panel)
1E
4C 33
Cowl Wire and Passenger Side J/B (Right Side of Grove Box)
4M 32

: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS

221
2005 HIGHLANDER (EWD592U)
Front Wiper and Washer
: GROUND POINTS

Code See Page Ground Points Location

222
2005 HIGHLANDER (EWD592U)
 MEMO

223
2005 HIGHLANDER (EWD592U)