Scribd
Upload
871 views9 pages

RIP Routing Configuration Using 3 Routers in Cisco Packet Tracer

RIP (Routing Information Protocol) is a distance-vector routing protocol that finds the best route between networks by calculating hop counts as the routing metric. The document provides steps to configure a network with 3 routers in Cisco Packet Tracer using RIP routing. This includes setting up devices, assigning IP addresses to PCs and router interfaces, enabling RIP on the routers by using the "network" command, and verifying connectivity by pinging devices.

Uploaded by

BBM Sathvik
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
871 views9 pages

RIP Routing Configuration Using 3 Routers in Cisco Packet Tracer

RIP (Routing Information Protocol) is a distance-vector routing protocol that finds the best route between networks by calculating hop counts as the routing metric. The document provides steps to configure a network with 3 routers in Cisco Packet Tracer using RIP routing. This includes setting up devices, assigning IP addresses to PCs and router interfaces, enabling RIP on the routers by using the "network" command, and verifying connectivity by pinging devices.

Uploaded by

BBM Sathvik
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 9

RIP Routing Configuration Using 3 Routers

in Cisco Packet Tracer


Routing Information Protocol (RIP) is an active routing protocol that operates hop
count as a routing metric to find the most suitable route between the source and
the destination network. It is a distance-vector routing protocol that has an AD
value of 120 and works on the Network layer of the OSI model.

Steps to Configure and Verify Three Router Connections in Cisco Packet


Tracer using RIP Routing:

Step 1: First, open the Cisco packet tracer desktop and select the devices given
below:
S.NO Device Model Name Qty.

1. PC PC 6

2. Switch PT-Switch 3

3. Router PT-router 3

IP Addressing Table:
S.NO Device IPv4 Address Subnet mask Default Gateway

1. PC0 192.168.10.2 255.255.255.0 192.168.10.1

2. PC1 192.168.10.3 255.255.255.0 192.168.10.1

3. PC2 192.168.20.2 255.255.255.0 192.168.20.1

4. PC3 192.168.20.3 255.255.255.0 192.168.20.1

5. PC4 192.168.30.2 255.255.255.0 192.168.30.1

6. PC5 192.168.30.3 255.255.255.0 192.168.30.1

• Then, create a network topology as shown below the image.


• Use an Automatic connecting cable to connect the devices with others.
Step 2: Configure the PCs (hosts) with IPv4 address and Subnet Mask according to
the IP addressing table given above.
• To assign an IP address in PC0, click on PC0.
• Then, go to desktop and then IP configuration and there you will IPv4
configuration.
• Fill IPv4 address and subnet mask.
• Assigning an IP address using the ipconfig command, or we can also
assign an IP address with the help of a command.
• Go to the command terminal of the PC.
• Then, type iPConfig <IPv4 address><subnet mask><default gateway>(if
needed)
Example: iPConfig 192.168.10.2 255.255.255.0 192.168.10.1
• Repeat the same procedure with other PCs to configure them
thoroughly.
Step 3: Configure router with IP address and Subnet mask.
IP Addressing Table Router:
S.NO Device Interface IPv4 Address Subnet mask

FastEthernet0/0 192.168.10.1 255.255.255.0


router0
1. Serial2/0 10.0.0.1 255.0.0.0

router1 FastEthernet0/0 192.168.20.1 255.255.255.0


S.NO Device Interface IPv4 Address Subnet mask

Serial2/0 10.0.0.2 255.0.0.0

2. Serial3/0 11.0.0.1 255.0.0.0

FastEthernet0/0 192.168.30.1 255.255.255.0


router2
3. Serial2/0 11.0.0.2 255.0.0.0

• To assign an IP address in router0, click on router0.


• Then, go to config and then Interfaces.
• Make sure to turn on the ports.
• Then, configure the IP address in FastEthernet and serial ports according
to IP addressing Table.
• Fill IPv4 address and subnet mask.
• Repeat the same procedure with other routers to configure them
thoroughly.
Step 4: After configuring all of the devices we need to assign the routes to the
routers.
To assign RIP routes to the particular router:
• First, click on router0 then Go to CLI.
• Then type the commands and IP information given below.
CLI command : network <network id>
RIP Routes for Router0 are given below:
Router(config)#network 192.168.10.0
Router(config)#network 10.0.0.0
RIP Routes for Router1 are given below:
Router(config)#network 192.168.20.0
Router(config)#network 10.0.0.0
Router(config)#network 11.0.0.0
RIP Routes for Router2 are given below:
Router(config)#network 192.168.30.0
Router(config)#network 11.0.0.0
Step 5: Verifying the network by pinging the IP address of any PC.
• We will use the ping command to do so.
• First, click on PC0 then Go to the command prompt.
• Then type ping <IP address of targeted node>.
• As we can see in the below image we are getting replies which means the
connection is working properly.
Example : ping 192.168.20.2
• A simulation of the experiment is given below we are sending PDU
from PC0 to PC2 and PC3 to PC5:

You might also like