• Avoid operating or storing the unit in extremely humid, dusty, hot/cold environments, where

the operating temperature is outside the recommended range of -22°F to 140°F (–30°C to

HEW2PER2 WDR 4 MP IR Bullet Camera Note

60°C).
Do not apply power to the camera before completing installation.
Confirm the installation surface can support at least three times the weight of the
Quick Installation Guide camera.

Thank you for purchasing a Honeywell Performance Series IP

camera. Follow the instructions in this guide to install and log in
Before You Begin
to your camera. For instructions on configuring the camera, Before you begin, check that you have received all of the parts listed below. If any parts are missing
refer to the Performance Series IP Cameras User Guide on the or damaged, contact your dealer immediately.
installation CD that came with your camera.
• Camera • Self-tapping screws (×4)
If you require additional assistance, contact Tech Support • Installation CD • Plastic wall anchors (×4)
(contact info is listed on the back page).
• Quick installation guide • Mounting template
• Allen key (L-wrench)

Cautions and Warnings Preparing the Mounting Surface

Inspect the site where you want to install the camera. The mounting
CAUTION THIS SYMBOL INDICATES THAT surface must be flat and capable of supporting at least three times
DANGEROUS VOLTAGE
RISK OF ELECTRIC CONSTITUTING A RISK OF
the weight of the camera.
SHOCK ELECTRIC SHOCK IS PRESENT
DO NOT OPEN WITHIN THE UNIT.
Remove the backing from the mounting template sticker and affix
the sticker to the mounting surface.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
THIS SYMBOL INDICATES THAT Note If you are using the side exit for the cable, note the
SHOCK, DO NOT REMOVE THE COVER.
IMPORTANT OPERATING AND
NO USER-SERVICEABLE PARTS INSIDE. orientation of the cable exit notch. In outdoor installations the notch
MAINTENANCE INSTRUCTIONS
REFER SERVICING TO QUALIFIED SERVICE
ACCOMPANY THIS UNIT. should point downwards to prevent water from entering the camera
PERSONNEL.
housing.
WARNING To ensure compliance with electrical safety standards, this product is intended for Drill three screw holes at the locations indicated on the mounting
use with a Listed Power Adapter marked “Limited Power Source” or “LPS” on the unit, template sticker and insert the three supplied plastic anchors in the
output rated to 12 VDC, minimum 0.33 A, TMA=60 deg C, or from Power over holes.
Ethernet (PoE) provided by Listed Information Technology Equipment meeting IEEE If you are flush mounting the camera and want to store the cables
802.3af PoE standard. inside the wall or ceiling, drill a hole at the cable exit position on the
mounting template and then pull the cables through the hole.
WARNING The Ethernet connection is not intended to be connected to exposed (outside plant)
networks. Do not connect two power sources to the camera at the same time.
CAUTION Invisible LED radiation (850 nm). Avoid exposure to beam.

Important Safeguards
• Read and keep these instructions.
• Do not aim the camera toward a bright light source for extended periods to prevent damage to
the imager. Avoid operating the unit under or close to unstable light sources (may cause
flickering), or close to fluorescent lamps or objects reflecting light.
• Do not touch the camera lens.
• Do not drop the camera or subject it to physical shock.
• Do not use a strong or abrasive detergent when cleaning the camera.
Mounting the Camera Recommended Recorders
1. Loosen the locking screw on the camera enclosure to remove HEN*4 8/16/32/64-channel Focus 4K NVRs (H.264 and H.265)
the enclosure from the camera base. HEN*3 4/8/16/32-channel Performance Series NVRs (H.264 and H.265)
2. If local storage is needed, insert a microSD card into the HEN*2 4/8/16-channel Performance Series NVRs (H.264)
microSD card slot (refer to the right picture). HRHT4* 4/8/16-channel 4 MP HQA/IP/CVBS Hybrid DVRs (H.264)
3. Route the cables through the camera base.
4. Align the screw holes on the camera base with the plastic wall Regulatory Statements
anchors.
FCC Compliance
5. Attach the camera base to the mounting surface using the
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
supplied screws. to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
6. Connect the camera with the Ethernet cable and the power interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
cable. energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
a. Connect one end of the Ethernet cable to the RJ-45 port
installation.
on the camera.
If this equipment does cause harmful interference to radio or television reception, which can be
b. If the other end of the Ethernet cable is NOT connected to determined by turning the equipment off and on, the user is encouraged to try to correct the interference
a PoE (Power-over-Ethernet) switch or NVR, connect the by one or more of the following measures:
power connector of the camera to a 12 VDC power source. • Reorient or relocate the receiving antenna.
7. Reattach the enclosure to the base and tighten the locking • Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
screw.
connected.
8. Rotate the camera body to the desired position. • Consult the dealer or an experienced radio/TV technician for help.
Note Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Adjusting Zoom and Focus This Class B digital apparatus complies with Canadian ICES-003.
Manufacturer’s Declaration of Conformance
If the camera is connected to the PoE port of a Honeywell Embedded NVR, you can log on to the North America The equipment supplied with this guide conforms to UL 60950-1 and CSA C22.2 No.
camera directly from the NVR. 60950-1.
To log on to the camera from a PC: Europe The manufacturer declares that the equipment supplied is compliant with the European
Parliament and Council Directive on the restriction of the use of certain hazardous substances in
1. Install the Honeywell Config Tool from the installation CD. electrical and electronic equipment (2011/65/EU), General Product Safety Directive (2001/95/EC), and
2. Use the Config Tool to discover the camera and open the camera’s webpage. the essential requirements of the EMC directive (2014/30/EU), conforming to the requirements of
standards EN 55032 for emissions, EN 50130-4 for immunity, and EN 62368-1 for electrical equipment
3. Log on to the camera as the admin user. The default user name is admin (case-sensitive) and
safety.
the default password is 1234.
Note • Be sure to remember the password of the camera. If the password is lost, the WEEE (Waste Electrical and Electronic Equipment)
camera may need to be sent back to the factory for recovery. Correct disposal of this product (applicable in the European Union and other European
countries with separate collection systems). This product should be disposed of, at the end of
• Only Internet Explorer 11 (or later) is supported. its useful life, as per applicable local laws, regulations, and procedures.
• IP address of the device is assigned automatically by DHCP server. If the DHCP
server is not available, the device will acquire 192.168.1.108 as the default IP

4.
address.

Go to Setup CameraConditionsZoom and Focus. The following panel appears:

Honeywell
2700 Blankenbaker Pkwy, Aston Fields Road, Whitehouse Building #1, 555 Huanke Road,
Suite 150 Industrial Estate Zhang Jiang Hi-Tech Park
Louisville, KY, 40299, USA Runcorn, Cheshire, WA7 3DL, UK Pudong New Area, Shanghai,
www.honeywell.com/security www.honeywell.com/security/uk 201203, China
+1 800 323 4576 +1 44 (0) 1928 754 028 www.asia.security.honeywell.com
(North America only) (Europe only) +400 840 2233
• Click Zoom in + or Zoom out - to zoom in or out. (Asia Pacific only)
• Click Near - or Far + to focus near or far, or click Auto Focus to enable auto focus.
Document 800-24592 – Rev A – 08/2018
© 2018 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell
cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new additions to this publication may be issued to incorporate such changes.