Axial Piston Pump

Series PV
Variable Displacement

Catalogue HY11-3243/UK
September 2004
Catalogue HY11-3243/UK Axial Piston Pump
Series PV

Note
This document and other information from Parker Hannifin
GmbH, its subsidiaries, sales offices and authorized
distributors provide product or system options for further
investigation by users having technical expertise. Before you
select or use any product or system it is important that you
analyse all aspects of your application and review the
information concerning the product or system in the current
product catalogue. Due to the variety of operating conditions
and applications for these products or systems, the user,
through his own analysis and testing, is solely responsible
for making the final selection of the products and systems
and assuring that all performance and safety requirements
of the application are met. The products are subject to
change by Parker Hannifin GmbH at any time without notice.

PI PVplus UK.PMD RH

2 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Table of contents Series PV

Description Page

Introduction 4
Characteristics 5
Ordering code 6
Noise levels 8
Noise reduction measures 9
Efficiency and case drain flows 10
Dimensions 14
Mounting-, repair- and seal kits 24
Pump combinations
Dimensions 26
Thru drive, shaft load limitations 28
Compensators
Dimensions / Seal kit compensators 29
Pressure compensators 30
Load-Sensing compensators 31
Horse power compensators 32
Electrohydraulic p/Q control 34
Electrohydraulic p/Q control FP* / UP* 35
Electronic Module (analogue) 38
Electronic Module (digital) 39
Pump accessories PVAP* 40
Hydraulic circuit, ordering examples PVAC* 44
Proportional control valve 46
Safety manifolds PVAPS* 47
Accessories 52
General installation information 53

PI PVplus UK.PMD RH

3 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Introduction Series PV

Pump with Standard Pressure Compensator, code F*S Pump with Load-Sensing Compensator, code FFC
Ø0,8

Q PF Q

L P1 A L P1 A
PM P L P1 A PM P L P1 A

p p

S L = included S L = included

Technical Features
• Mounting interface according to VDMA-standards
sheet 24560 part 1
With thru drive for single and multiple pumps • Standard: 4-hole flange ISO 3019/2 (metric)
Swash plate type for open circuit Optional: 4-hole flange ISO 3019/1 (SAE)
• Large servo piston with strong bias spring achieves
fast response; e.g. for PV046
upstroke < 70 ms
downstroke < 40 ms
Note: Follow installation instructions.
• Reduced pressure peaks due to active decompres-
sion of system at downstroke
• Also at low system pressure reliable compensator
operation. Lowest compensating pressure 12-15 bar
• 9 piston and new precompression technology
(precompression volume) result in unbeaten low out-
let flow pulsation.
• Rigid and FEM-optimized body design for lowest
noise level
• Complete compensator program
• Thru drive for 100% nominal torque
• Pump combinations (multiple pumps) of same size
and model and mounting interface for basically all
metric or SAE mounting interfaces
Pump with Horse Power Compensator, code *LB Pump with Electrohydr. Displacement Control, code FPV

PP

UQ Q
L P1 A L P1 A
PM P L P1 A PL Q PM P L P1 A
U
s UQ

p
S L = included S L = included

PI PVplus UK.PMD RH

4 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Characteristics Series PV

Technical data

Displacement [cm3/rev] from 16 to 270

Operating pressures
Outlet [bar] nominal pressure pN 350
[bar] max. pressure pmax. 420 1)

[bar] drain port 2 2)

Inlet min. [bar] 0.8 (absolute)

max. [bar] 16
Minimum speed [min-1] 300 min-1
Pump with Standard Pressure Comp. Pump with Horse Power Comp.
Mounting interface 4-hole flange ISO 3019/2
optional ISO 3019/1, SAE
Installation drain port as high as possible

1)
max. 20% of working cycle
2)
peak pressure only, special version up to 20 bar available
(with X-Modification X5877)

Pump combinations
See pages 26–27 Combination PV/PV Combination PV/PGP

Selection table

Model Max. displacement Output flow Input horse power at Max speed * Moment of Weight
[cm3/rev] at 1500 min-1 [l/min] 1500 min-1 and 350 bar [kW] [min-1] inertia [kgm²] [kg]

PV016 16 24 15.5
PV020 20 30 19.5 3000 0.0017 19
PV023 23 34.5 22.5
PV032 32 48 31
PV040 40 60 39 2800 0.0043 30
PV046 46 69 45
PV063 63 94.5 61.5 2800
PV080 80 120 78 2500 0.018 60
PV092 92 138 89.5 2300
PV140 140 210 136 2400
0.030 90
PV180 180 270 175 2200
PV270 270 405 263 1800 0.098 172
* The maximum speed ratings are shown for an inlet pressure of 1 bar (absolute) and for a fluid viscosity of ν = 30 mm²/s.

PI PVplus UK.PMD RH

5 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Ordering Code Series PV

PV
Pump Compensator
Axial piston Size Variation Threads 2nd Compensator Design
pump and pump series:
variable displacement (not required
displacement for order)
high
pressure Rotation Mounting
version code Thru drive Seals
see opposite page

Code Displacement Code Seals

016 16 cm³/rev N NBR
020 20 cm³/rev V FPM
023 23 cm³/rev E EPDM
032 32 cm³/rev
W NBR with PTFE shaft seal
040 40 cm³/rev
P FPM with PTFE shaft seal
046 46 cm³/rev
063 63 cm³/rev S EPDM with PTFE shaft seal
080 80 cm³/rev
092 92 cm³/rev
140 140 cm³/rev Code 2nd pump option7)
180 180 cm³/rev
Single pump, no 2nd pump
270 270 cm³/rev 1
and coupling
2 PV140 or PV180 mounted
1)
Code Rotation 3 PV or PVM pump mounted
R Clockwise 4 Gear pump series PGP mounted
L Counter clockwise 7)
Specify 2nd pump with full model code
1)
When looked on shaft

Code Thru drive option

Code Variation
no adaptor for 2nd pump
1 Standard Single pump
T prepared for thru drive
9 Reduced displace-
ment adjusted 2) With adaptor for 2nd pump
2)
For order specify dis- Y8) SAE AA, Ø 50.8mm
placement. A SAE A, Ø 82.55mm
B SAE B, Ø 101.6mm
Code Mounting interface Shaft C9) SAE C, Ø 127mm
D10) SAE D, Ø 152.4mm
D 4-hole flange Cylindric, key
SAE E11) SAE E, Ø 165.1mm
E 4-hole flange Splined, SAE
ISO G12) Metric, Ø 63mm
F3) 3019/1 4-hole flange Cylindric, key
H Metric, Ø 80mm
G3) 4-hole flange Splined, SAE
J Metric, Ø 100mm
K metr. ISO 4-hole flange Cylindric, key K9) Metric, Ø 125mm
L 3019/2 4-hole flange Splined, DIN 5480 L10) Metric, Ø 160mm
3)
Codes F and G only for PV140/180, see dimension sheet M11) Metric, Ø 200mm
8)
Only for PV016 - PV023
Code Port 4) Threads5) 9)
Only for PV032 and larger
10)
Only for PV063 and larger
1 BSPP Metric 11)
Only for PV270
3 UNF UNC 12)
Only for PV016 - PV092
46) BSPP Metr. M14
7 ISO 6149 UNC
8 ISO 6149 Metric1)
4)
Drain, gauge and flushing ports
5)
All mounting and connecting threads
6)
For PV063-PV180 only: pressure port 1 1/4" with 4 x M14 instead of 4 x M12

PI PVplus UK.PMD RH

6 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Ordering Code Series PV

PV
Compensator Pump Compensator
Design series:
not required
for order

Standard Pressure Compensator Electrohydraulic compensator

Code Compensator options Code Compensator option
0 0 1 No compensator Pilot pressure supply
1 0 0 With coverplate, no control function F Standard (internal), no shuttle valve
F D S 10 - 140 bar, spindle + lock nut U Elbow manifold, compensator horizontal 16)
F H S 40 - 210 bar, spindle + lock nut Function
F W S 70 - 350 bar, spindle + lock nut P Proportional displacement control
Remote Compensator options Variation
F R Remote pressure compensator V Standard, no pressure compensation
F S Variation R, for quick unload valve R Remote pressure comp. NG6 interface
F F Load-Sensing compensator Variation R, Pressure sensor and
F T Two valve load-sensing compensator G proportional pilot valve mounted for
pressure resp. horse power control
Variations for Remote Compensator
C External pressure pilot 13) Variation R, Proportional pilot valve
D
PVACPP* mounted
1 NG6/D03 interface top side
14)
2 Like 1 but with ext. pilot port 15) Z Variation R, accessories mounted
P Pilot valve PVAC1P* mounted Remote pressure comp., NG6 interface
S top side, for quick unload valve
Proportional pilot valve type
D
PVACPP* mounted Variation S, pressure sensor and
L Pilot valve with DIN lock mounted T proportional pilot valve mounted for
pressure resp. horse power control
Z Accessory mounted 14)
Remote pressure comp., NG6 interface top
Horse power compensator P side, for preload and quick unload manifold
Code Displacement Compensator option Variation P, pressure sensor and
016 032 063 Nom. HP [kW] Nom. torque E proportional pilot valve mounted for
023 046 092 140 180 270 at 1500 min-1 [Nm] pressure resp. horse power control
16)
B x 3 19.5 not for *UPV
C x 4 26
D x x 5.5 36
E x x 7.5 49
G x x x 11 71
H x x x 15 97
K x x x x 18.5 120
M x x x x 22 142
S x x x x 30 195
T x x x x 37 240 Note
U x x x x 45 290 Compensator differential ∆p is to be adjusted:
W x x x x 55 355
Remote pressure comp., horse power comp. 15 ± 1 bar
Y x x x 75 485
Z x x x 90 585 (Codes FR*, FT*, *L*, *C*, FPR, FPD, FPZ, FPG)
2 x x 110 715 With quick unload manifold 12 ± 1 bar
3 x 132 850 (Codes FS*, FPS, FPT, FPP, FPE)
Function
Load-Sensing comp. (not horse power comp.) 10 ± 1 bar
L x x x x x x Horse power compensator
(Codes FF*)
Horse power compensator and
C x x x x x x load-sensing The ordering code PVACPP* correspond to the
DSAE1007P07*
Variation
A x x x x x x NG6 interface top side
B x x x x x x No pressure compensation
Adjustable
C x x x x x x pressure compensation 13)
Not for two-valve-compensator
14)
D x x x x x x Proportional pilot valve Accessories not included,
please specify on order with full
PVACPP* mounted
model code.
14)
Z x x x x x x Accessories mounted 15)
Only for Codes *FR* and *FT*
PI PVplus UK.PMD RH

7 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Noise Levels Series PV

PV016 - PV023 PV140

PV032 - PV046 PV180

PV063 - PV092 PV270

Typical sound level for single pumps, measured in unechoic chamber All data measured with mineral oil viscosity 30 mm²/s (cSt) at 50°C.
according to DIN 45 635, part 1 and 26. Microphone distance 1m;
speed: n = 1500 min-1.

PI PVplus UK.PMD RH

8 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Noise Reduction Measures Series PV

Operating noise of pumps

The normal operating noise of a pump and consequently Last but not least the connection between pump and
the operating noise of the entire hydraulic system are driving motor can be the cause of an unacceptably high
largely determined by where and how the pump is noise emission. Even when the mounting space is limited
mounted and how it is connected to the downstream there are suitable means and components to reduce the
hydraulic system. noise significantly.
Also size, style and installation of the hydraulic tubing The vibration of the pump body, created by high alternat-
have a major influence on the overall noise emitted by a ing forces in the rotating group and the pulsation of the
hydraulic system. output flow excite every part of the system connected to
the pump mechanically or hydraulically.
Noise reduction measures
Talking about operating noise of a hydraulic pump,
primary and secondary pump noise has to be taken into
consideration.
Primary pump noise is caused by vibrations of the
pump body due to internal alternating forces stressing
the body structure.
Flexible elements help to prevent pump body vibration
being transmitted to other construction elements, where
possible amplification may occur. Such elements can be:
• Bell housing with elastic dampening flange with
vulcanized labyrinth (1)
1) Bell housing 2) Coupling 3) Damping rails
• Floating and flexible coupling (2)
• Damping rails (3) or silent blocks for mounting the Figure 1: Components to avoid vibration transfer from the pump to
the drive/installation and their position in the power unit (numbers
electric motor or the foot mounting flange
refer to the text on the left)
• Flexible tube connections (compensators) or hoses
on inlet, outlet and drain port of the pump
series 20

series 40
• Exclusive use of gas tight tube fittings for inlet
connections to avoid ingression of air causing cavitation
and excessive noise 200
[bar] 220
Secondary pump noise is caused by vibration induced
PV180R1K1T1NFWS-series 20 [bar]
into all connected hydraulic components by the flow and 180
pressure pulsation of the pump. This secondary noise 200
adds typical 7 - 10 dB(A) to the noise of a pump measured
in the sound chamber according to DIN 45 635 (see 160 PV180R1K1T1NFWS-series 40
diagrams on opposite side). Therefore pipework, its 180
9.0 9.5 10.0 10.5 11.0 [s] 11.5
mounting and the mounting of all hydraulic components
like pressure filters and control elements have a major
influence on the overall system noise level. Figure 2: Comparison of the pressure pulsation in a system with 6
old PV pumps versus the same system with 6 PVplus pumps. The
Pulsation reduction with precompression volume pulsation reduction effect of the precompression volume is evident.
The PV is equipped with a new technology for flow ripple
reduction. This method reduces the pulsation at the pump
outlet by 40 - 60 %. That leads to a significant reduction
of the overall system noise without additional cost and
Other measures
without additional components (silencers etc.). The typical
reduction reaches 2 - 4 dB(A). That means: with a pump Small diameter tubes do not only cause high flow speeds,
of the PV series the secondary noise adds only some 5 turbulences inside the tubes and cavitation in the pump,
- 7 dB(A) to the pump noise instead of 7 - 10 dB(A) as they also produce noise.
usually found. Only correctly sized connections of the largest possible
Figure 2 compares the measured pulsation of a system diameter according to the port size of the pump should be
with 6 pumps of 180 cm³/rev each. used.

PI PVplus UK.PMD RH

9 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Efficiency and Case Drain Flows Series PV

Efficiency, power consumption Efficiency and case drain flows PV016, PV020, PV023
PV016 The efficiency and power graphs are measured at an
20 input speed of n = 1500 min-1, a temperature of 50°C and

Efficiency [%] (overall, volumetric)

Input power [kW]

25 100
Output flow [l/min]

vol. efficienc a fluid viscosity of 30 mm2/s.

output flow y
overall efficiency Case drain flow and compensator control flow leave via
20 16 80 the drain port of the pump. To the values shown are to be
added 1 to 1.2 l/min , if at pilot operated compensators
(codes FR*, FF*, FT*, horse power compensator and p/
15 12 60
Q-control) the control flow of the pressure pilot valve also
low goes through the pump.
u ll f
tf
10 8 ra 40 Please note: The values shown below are only valid for
we
t po static operation. Under dynamic conditions and at rapid
u
inp compensation of the pump the volume displaced by the
5 4 20 servo piston also leaves the case drain port. This dy-
ea d namic control flow can reach up to 40 l/min! Therefore the
t deadh
input power a case drain line is to lead to the reservoir at full size and
0 0 0 without restrictions as short and direct as possible.
0 100 200 300
Pressure [bar]
PV020
25 100
Efficiency [%] (overall, volumetric)

30
Input power [kW]
Output flow [l/min]

output flow, vo
l. efficiency
Case drain flows PV016-023
overall efficiency
24 20 80

18 15 60
low
ll f
fu
r at
12 10 e 40
ow
utp
inp
6 5 20
d
ea dhea
inpu t power at d
0 0 0
0 100 200 300
Pressure [bar]
PV023
100
Efficiency [%] (overall, volumetric)

40 25 vo
Input power [kW]
Output flow [l/min]

l. efficiency
overall efficiency
32 20 output flow 80

24 15 w 60
lo
lf
ful
at
wer
16 10 po 40
ut
i np

8 5 20
d
ea dhea
inpu t power at d
0 0 0
0 100 200 300
Pressure [bar]

PI PVplus UK.PMD RH

10 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Efficiency and Case Drain Flows Series PV

Efficiency, power consumption Efficiency and case drain flows PV032, PV040, PV046
PV032 The efficiency and power graphs are measured at an
input speed of n = 1500 min-1, a temperature of 50°C and

Efficiency [%] (overall, volumetric)

50 40 vol. efficiency 100
Input power [kW]
Output flow [l/min]

output flow a fluid viscosity of 30 mm2/s.

overall efficiency Case drain flow and compensator control flow leave via
40 32 80
the drain port of the pump. To the values shown are to be
added 1 to 1.2 l/min , if at pilot operated compensators
(codes FR*, FF*, FT*, horse power compensator and p-
30 24 60
w
Q-control) the control flow of the pressure pilot valve also
l flo goes through the pump.
ful
r at
20 16 e 40 Please note: The values shown below are only valid for
ow
utp static operation. Under dynamic conditions and at rapid
inp compensation of the pump the volume displaced by the
10 8 20 servo piston also leaves the case drain port. This dy-
namic control flow can reach up to 60 l/min! Therefore the
adhead
input power at de case drain line is to lead to the reservoir at full size and
0 0 0
0 100 200 300 without restrictions as short and direct as possible.
Pressure [bar]
PV040
Efficiency [%] (overall, volumetric)

40 out 100
Input power [kW]
Output flow [l/min]

60
put flow, vol. efficiency
Case drain flows PV032-046
overall efficiency
48 32 80

36 24 60
low
f ull f
a t
24 16 er 40
pow
t
in pu

12 8 20

eadhead
input power at d
0 0 0
0 100 200 300
Pressure [bar]
PV046
50
Input power [kW]

Efficiency [%] (overall, volumetric)

80
Output flow [l/min]

100
vol. efficiency
overall efficiency

64 40 output flow 80

48 30 60
low
u ll f
a tf
er
32 20 p ow 40
t
pu
in

16 10 20

head
input power at dead
0 0 0
0 100 200 300
Pressure [bar]

PI PVplus UK.PMD RH

11 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Efficiency and Case Drain Flows Series PV

Efficiency, power consumption Efficiency and case drain flows PV063, PV080, PV092
PV063 The efficiency and power graphs are measured at an
100 input speed of n = 1500 min-1, a temperature of 50°C and

Efficiency [%] (overall, volumetric)

100 70
Input power [kW]
Output flow [l/min]

vol. efficiency
output flow
a fluid viscosity of 30 mm2/s.
overall efficiency Case drain flow and compensator control flow leave via
80 56 80 the drain port of the pump. To the values shown are to be
added 1 to 1.2 l/min , if at pilot operated compensators
(codes FR*, FF*, FT*, horse power compensator and p-
60 42 w 60
lo Q-control) the control flow of the pressure pilot valve also
ll f
t fu goes through the pump.
e ra
40 28 ow 40 Please note: The values shown below are only valid for
tp
pu static operation. Under dynamic conditions and at rapid
in
compensation of the pump the volume displaced by the
20 14 20 servo piston also leaves the case drain port. This dy-
d
a dh ea namic control flow can reach up to 80 l/min! Therefore the
er at de
inp ut p o w case drain line is to lead to the reservoir at full size and
0 0 0
0 100 200 300 without restrictions as short and direct as possible.
Pressure [bar]
PV080
100
Efficiency [%] (overall, volumetric)

120 80
Input power [kW]
Output flow [l/min]

output flow, vol.

efficiency
Case drain flows PV063-092
overall efficiency
96 64 80

w
48 f lo
72 ll 60
t fu
ra
owe
48 32 tp 40
pu
in

24 16 20
h ead
r at dea d
input powe
0 0 0
0 100 200 300
Pressure [bar]
PV092
Efficiency [%] (overall, volumetric)

150 100 100

Input power [kW]
Output flow [l/min]

output flow vol. efficiency

cy
overall efficien
120 80 80

90 60 w 60
lo
lf
ful
at
wer
40 o
60 tp 40
npu
i

30 20 20
d
dea dh ea
inpu t power at
0 0 0
0 100 200 300
Pressure [bar]

PI PVplus UK.PMD RH

12 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Efficiency and Case Drain Flows Series PV

Efficiency, power consumption Efficiency and case drain flows PV140, PV180, PV270
PV140 The efficiency and power graphs are measured at an
100 input speed of n = 1500 min-1, a temperature of 50°C and

Efficiency [%] (overall, volumetric)

250 150
Input power [kW]
Output flow [l/min]

vol. efficiency
a fluid viscosity of 30 mm2/s.
overall efficiency
Case drain flow and compensator control flow leave via
200 120 output flow 80
the drain port of the pump. To the values shown are to be
added 1 to 1.2 l/min , if at pilot operated compensators
90 w
(codes FR*, FF*, FT*, horse power compensator and p-
150 lo 60
lf Q-control) the control flow of the pressure pilot valve also
f ul
at goes through the pump.
wer
100 60 o 40 Please note: The values shown below are only valid for
tp
pu static operation. Under dynamic conditions and at rapid
in
compensation of the pump the volume displaced by the
50 30 20 servo piston also leaves the case drain port. This dy-
a d he ad namic control flow can reach up to 120 l/min! Therefore
i np ut power at de the case drain line is to lead to the reservoir at full size and
0 0 0
0 100 200 300 without restrictions as short and direct as possible.
Pressure [bar]
PV180 Case drain flows PV140-180
100
Efficiency [%] (overall, volumetric)

300 175
Input power [kW]
Output flow [l/min]

vol. efficiency

output flow
240 140 80
iency
ffic

w
lo
ll f
overall e

180 105 60
fu
at
wer
t po
120 70 pu 40
in

60 35 20

ad he ad
in pu t power at de
0 0 0
0 100 200 300
Pressure [bar]
PV270 Case drain flows PV270
Efficiency [%] (overall, volumetric)

500 250 100

Input power [kW]
Output flow [l/min]

vol. efficiency
ll efficie ncy
overa
output flow
400 200 80
w
lo
lf
ul

300 150 60
f
r at
we
tpo
pu

200 100 40
in

100 50 20

dhea d
input powe r at dea
0 0 0
0 100 200 300
Pressure [bar]

PI PVplus UK.PMD RH

13 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Dimensions Series PV

PV016 - 023, metric version

drain port L2; G1/2
mounting hole for optional M 22 x 1.5; ISO 6149-1
horse power compensator pilot (threads options 7 and 8)
or displacement feedback LVDT or 7/8 - 14 UNF
(threads option 3) 140

94
16.5 120
Ø 25k6
Ø 100h8

16.5
80
13
drain port L1, 9
dimensions see L2 32
52 max. 133
132

197.5 View X
9
max. 212 10
Shown with standard pressure compensator
gage port M; G1/4
optional M 12 x 1.5; ISO 6149-1
(threads options 7 and 8)
oder 7/16 - 20 UNF
(threads option 3)

89
12
55 28-0.25
48
thread M10 - 22 deep 125
15

key 8 x 7 x 40
X DIN 6885

127 22
162 flushing port L3; G 3/8
170.5 optional M 18 x 1.5; ISO 6149-1
(threads options 7 and 8)
Inlet: oder 3/4 - 16 UNF
flange according ISO 6162 (threads option 3)
DN 32; PN 250 bar
58.7 The pump shown above has mounting option K
32 and thru drive option T (prepared for thru drive).

4 x M10, 18 deep
30.2 optional 7/16 - 14 UNC - 2B
(threads options 3 and 7) Ø 100h8

4 x M10, 18 deep mounting option L

23.8
optional 3/8 - 16 UNC - 2B splined shaft W 25 x 1.5 x 15 x 8f DIN 5480
(threads options 3 and 7)

50.8 19
Outlet: 43
flange according ISO 6162
DN 19; PN 400 bar
For further information about flanges see catalogue No. 4039/UK „Pressure Hydraulic Flanges“ (on request).
Shown is a clockwise rotating pump. Counter clockwise rotating pumps have inlet, outlet and gauge ports reversed.
PI PVplus UK.PMD RH

14 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Dimensions Series PV

PV016 - 023, SAE version and thru drive

13.5
Ø 25.4-0.05
28.17±0.13
Ø 101.6-0.05 89.8

thread
3/8-16 UNC-2B 44.9
22 deep

9.4 key
8 6.35 x 6.35
44.9
42 40 long
89.8
50
Shown above is mounting option D

Ø 101.6-0.05
mounting option E
splined shaft 15T 16/32 DP, flat root, side fit
ANSI B92.1

46

Variation with thru drive

drive output: splined shaft

13T-16/32 DP, flat root, side fit
ANSI B92.1

A
G C

B H
197.5 D
F
225
47.5

Thru shaft adaptors are available with the following dimensions: Dimension H and available couplings see page 24.
At threads options 3 and 7 the dimensions E and G are UNC - 2B
A B C D E F G threads.
63 10 85 - M8 100 M8
80 10 103 - M8 109 M10
100 10.5 125 - M10 - -
50.8 10 - - - 82 M8
82.55 10 - - - 106 M10
101.6 10.5 - 89.8 M12 - -

PI PVplus UK.PMD RH

15 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Dimensions Series PV

PV032 - 046, metric version

drain port L2; G3/4
optional M 27 x 2; ISO 6149-1 153
mounting hole for (threads options 7 and 8)
horse power compensator pilot or 1 1/16 - 12 UNF
or displacement feedback LVDT (threads option 3)

107
22
Ø 32k6

Ø 125h8

150

92
22

drain port L1, 15

dimensions see L2 37 max. 133
9
227 68 156
max. 245 View X
9
gage port M; G1/4
10 Shown with standard pressure compensator
optional M 12 x 1.5; ISO 6149-1
(threads options 7 and 8)
oder 7/16 - 20 UNF
(threads option 3)

98
14

66 35-0.25 160
60
Thread M10 - 22 deep
17

Key 10 x 8 x 56
X DIN 6885

146 28

185 flushing port L3; G 1/2

optional M 22 x 1.5; ISO 6149-1
197 (threads options 7 and 8)
oder 7/8 - 14 UNF
Inlet: (threads option 3)
flange according ISO 6162
DN 38; PN 200 bar
69.9 The pump shown above has mounting option K
38
and thru drive option T (prepared for thru drive)
4 x M12, 18 deep
optional 1/2 - 13 UNC - 2B
(threads options 3 and 7)
35.7
4 x M12, 18 deep Ø 125 h8
27.8
optional 7/16 - 14 UNC - 2B
mounting option L
(threads options 3 and 7)
splined shaft W 32 x 1.5 x 20 x 8f DIN 5480

25
57.2
Outlet:
flange according ISO 6162
47
DN 25; PN 400 bar
For further information about flanges see catalogue No. 4039/UK „Pressure Hydraulic Flanges“ (on request).
Shown is a clockwise rotating pump. Counter clockwise rotating pumps have inlet, outlet and gauge ports reversed.
PI PVplus UK.PMD RH

16 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Dimensions Series PV

PV032 - 046, SAE version and thru drive version

Variation with thru drive

drive output: splined shaft
W 25 x 1.5 x 15 x 8f DIN5480

A
C
G

H
227 B D
L F
K

Thru shaft adaptors are available with the following dimensions: Dimension H and available couplings see page 24.
At threads options 3 and 7 the dimensions E and G are UNC - 2B
A B C D E F G K L threads.
63 8.5 85 - M8 100 M8 49 261
80 8.5 103 - M8 109 M10 49 261
100 10.5 125 - M10 140 M12 49 261
125 12 160 - M12 - - 49 261
82.55 8 - - - 106 M10 49 261
101.6 11 - 89.8 M12 146 M12 49 261
127 13.5 - 114.5 M12 - - 64 276

PI PVplus UK.PMD RH

17 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Dimensions Series PV

PV063 - 092, metric version

For further information about flanges see catalogue No. 4039/UK „Pressure Hydraulic Flanges“ (on request).
Shown is a clockwise rotating pump. Counter clockwise rotating pumps have inlet, outlet and gauge ports reversed.
PI PVplus UK.PMD RH

18 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Dimensions Series PV

PV063 - 092, SAE version and thru drive version

Variation with thru drive

drive output: splined shaft
W 32 x 1.5 x 20 x 8f DIN5480

A C

H
287 B
L D
K F

Thru shaft adaptors are available with the following dimensions: Dimension H and available couplings see page 24.
At threads options 3 and 7 the dimensions E and G are UNC - 2B
A B C D E F G K L
threads.
63 10 85 - M8 100 M8 58 326
80 10 103 - M8 109 M10 58 326
100 12 125 - M10 140 M12 58 326
125 12 160 - M12 180 M16 58 326
160 12 200 - M16 - - 58 326
82.55 10 - - - 106 M10 58 326
101.6 12 - 89.8 M12 146 M12 58 326
127 14 - 114.5 M12 181 M16 58 326
152.4 14 - 161.6 M16 - - 78 346
PI PVplus UK.PMD RH

19 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Dimensions Series PV

PV140 - 180, metric version

drain port L2; G1

mounting hole for optional M 33 x 2; ISO 6149-1
horse power compensator (threads options 7 and 8)
pilot or LVDT for or 1 5/16 - 12 UNF 204
displacement feedback (threads option 3)

158

Ø 50k6
Ø 160h8
35

35 200

145

drain port L1 20
dimensions see L2 48
350 9
max. 133
max. 385 92
200
9
gage port M; G1/4 10 View X
optional M 12 x 1.5; ISO 6149-1 Shown with standard pressure compensator
(threads options 7 and 8)
oder 7/16 - 20 UNF
(threads option 3)

147
283
18
106
53.5-0.25
105 200
Thread M16 - 36 deep

Key 14 x 9 x 75
DIN 6885
X

233 40
pressure port: 295 flushing port L3; G 3/4
suction port: 305 optional M 27 x 2; ISO 6149-1
Inlet: (threads options 7 and 8)
flange according ISO 6162 oder 1 1/16 - 12 UNF
DN 64; PN 160 bar (threads option 3)
88.9 The pump shown above has mounting option K
64 and thru drive option T (prepared for thru drive).
4 x M12, 20 deep
optional 1/2 - 13 UNC - 2B
(threads options 3 and 7)
50.8
4 x M12, 20 deep Ø 160h8
31.8 optional 1/2 - 13 UNC - 2B
mounting option L
(threads options 3 and 7)
splined shaft W 50 x 2 x 24 x 9g DIN 5480
or threads option 4
(M14, 22 deep)
66.6 32
Outlet:
flange according ISO 6162 78
DN 32; PN 400 bar

For further information about flanges see catalogue No. 4039/UK „Pressure Hydraulic Flanges“ (on request).
Shown is a clockwise rotating pump. Counter clockwise rotating pumps have inlet, outlet and gauge ports reversed.
PI PVplus UK.PMD RH

20 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Dimensions Series PV

PV140 - 180, SAE version and thru drive version

Variation with thru drive

drive output: splined shaft
W 40 x 1.5 x 25 x 8f DIN5480

A C
G

B H

350 D
415 F
97

Thru shaft adaptors are available with the following dimensions: Dimension H and available couplings see page 24.
At threads options 3 and 7 the dimensions E and G are UNC - 2B
A B C D E F G threads.
80 10 103 - M8 109 M10
100 12 125 - M10 140 M12
125 12 160 - M12 180 M16
160 12 200 - M16 - -
82.55 10 - - - 106 M10
101.6 12 - 89.8 M12 146 M12
127 14 - 114.5 M12 181 M16
152.4 14 - 161.6 M16 - -

PI PVplus UK.PMD RH

21 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Dimensions Series PV

PV 270, metric version

For further information about flanges see catalogue No. 4039/UK „Pressure Hydraulic Flanges“ (on request).
Shown is a clockwise rotating pump. Counter clockwise rotating pumps have inlet, outlet and gauge ports reversed.
PI PVplus UK.PMD RH

22 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Dimensions Series PV

PV 270, SAE version and thru drive version

Variation with thru drive

output: splined shaft
W 50 x 2 x 24 x 9g DIN 5480

A C

472.5 D
531.5 F
97

Thru shaft adaptors are available with the following dimensions:

Dimension H and available couplings see page 24.
A B C D E F G
At threads options 3 and 7 the dimensions E and G are UNC - 2B
80 8.5 103 - M8 109 M10 threads.
100 10.5 125 - M10 140 M12
125 10.5 160 - M12 180 M16
160 13.5 200 - M16 224 M20
200 13.5 250 - M20 - -
82.55 8 - - - 106 M10
101.6 11 - 89.8 M12 146 M12
127 13.5 - 114.5 M12 181 M16
152.4 13.5 - 161.6 M16 229 M20
165.1 17 - 224.5 M20 - -
PI PVplus UK.PMD RH

23 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Kits Series PV

Mounting kits for multiple pumps, for second pump option

MK PV BG
Mounting Axial Size Second Thread Seals Design
kit piston pump series
pump (see name
plate)
series PV

Code Pump size Code Seals

N NBR
1 Pump size 1: PV016 - PV023
Code Second pump, SAE V FPM
2 Pump size 2: PV032 - PV046 E EPR
T Prepared for thru drive option (plugged)
3 Pump size 3: PV063 - PV092
Y SAE AA, diameter 50.8 mm
4 Pump size 4: PV140 - PV180
A SAE A, diameter 82.55 mm
5 Pump size 5: PV270 B SAE B, diameter 101.6 mm Code Thread
C SAE C, diameter 127,mm M Metric
D SAE D, diameter 152.4 mm S SAE
E SAE E, diameter 165.1 mm
Second pump, metric
G Diameter 63 mm
H Diameter 80 mm
J Diameter 100 mm
K Diameter 125 mm
Kit contains positions 30, 69, 84, L Diameter 160 mm
85 and 87, see drawing below. M Diameter 200 mm

Mounting kits for multiple pumps, couplings

MK PV BG K
Mounting Axial Size Coupling Design
kit piston series
pump (see name
plate)
series PV

Code Pump size Code Coupling for metric,

splined shaft DIN 5480
1 Pump size 1: PV016 - PV023
01 N25 x 1.5 x 15
2 Pump size 2: PV032 - PV046
SAE, 02 N32 x 1.5 x 20
3 Pump size 3: PV063 - PV092 03 N40 x 1.5 x 25
splined
4 Pump size 4: PV140 - PV180 04 N50 x 2 x 24
5 Pump size 5: PV270 05 N60 x 2 x 28
Coupling for SAE splined shaft
flat root, side fit
Kit contains positions 91 (and 92 for 11 9T 16/32
keyed shaft). 12 11T 16/32
keyed shaft, 13 13T 16/32
(only up to Ø 18, 14 15T 16/32
metric) 15 14T 12/24
16 17T 12/24
85 87 17 13T 8/16
18 15T 8/16
92 Coupling + adaptor
for keyed shaft
20 Diameter 12 mm
metric, 21 Diameter 16 mm
69 splined 22 Diameter 18 mm

front pump 30 84 91 second pump

PI PVplus UK.PMD RH

24 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Kits Series PV

Seal kits
SK PV BG
Seal kit Axial Size Seals Thread, Design
piston port series
pump (see name
plate)
series PV
C
Code Pump size Code Thread Port
1 Pump size 1: PV016 - PV023 Code Seals 1 Metric BSPP
2 Pump size 2: PV032 - PV046 N NBR 3 UNC UNF
V FPM 7 UNC ISO 6149
3 Pump size 3: PV063 - PV092
E EPR 8 Metric ISO 6149
4 Pump size 4: PV140 - PV180
W NBR with PTFE shaft seal
5 Pump size 5: PV270 P FPM with PTFE shaft seal
S EPDM with PTFE shaft seal

Repair and spare parts kits

RK PV BG
Spare Axial Size Contents partly Design
parts kit piston optional:Thread series
pump or rotation or (see name
plate)
series PV seals
Code Pump Size Code Thread
1 Pump size 1: PV016 - PV023 M Metric
2 Pump size 2: PV032 - PV046 Code Contents Optional S SAE / UNC
3 Pump size 3: PV063 - PV092 VT Connecting parts, kit Thread Rotation
4 Pump size 4: PV140 - PV180 WP Shaft with key Thread R Clockwise
5 Pump size 5: PV270 WZ Splined shaft Thread L Counter-clockw.
SS Valve plate Rotation
Seals
SB Bushing for servo piston Seals
N NBR
Contents - fixed
V FPM
GLE Trunnion bearing kit E EPR
ROG Rotating unit incl. piston set
KOS Piston set
SRS Swash plate
WQS Shaft with key, reinforced, only for size 4, only with SAE
WFS Splined shaft, reinforced, only for size 4, only with SAE
RFE Bias spring kit
SKS Servo piston kit

Repair and spare parts kits for adjustable displacement limiter

RK PV
Spare Axial Displace- Contents Seals Design
parts kit piston ment series
pump (see name
plate)
series PV
Code Displacement Code Seals
016 PV016 063 PV063 N NBR
020 PV020 080 PV080 V FPM
023 PV023 092 PV092 E EPR
032 PV032 140 PV140 Code Contents
040 PV040 180 PV180 For parts included, see spare parts list PVI-BGx-GB-yy; available upon request.
HE Displacement limiter
x stands for frame size 1 - 5
046 PV046 270 PV270 adjustable yy stands for design series
PI PVplus UK.PMD RH

25 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Pump Combinations Series PV

Combinations PV / PV or PV / PVM (metric version)

M K B

D C

Main pump Second pump Interface main pump L B C D H K M

PV016, 020 or 023 PV016, 020 or 023 100 B4 HW 489 196 170.5 225 220 225 212
PV016, 020 or 023 541 208 197 235.5 245 261 212
PV032, 040 or 046 PV032, 040 or 046 125 B4 HW 574 197 261 245 261 245
208
PV016, 020 or 023 630 232 252 244.5 299 326 212
PV063, 080 or 092 PV032, 040 or 046 160 B4 HW 663 232 252 271 299 326 245
PV063, 080 or 092 724 232 252 326 299 326 306
PV016, 020 or 023 719 230 305 280.5 349 415 212
PV032, 040 or 046 752 230 305 307 349 415 245
PV140 or 180 160 B4 HW
PV063, 080 or 092 813 230 305 362 349 415 306
PV140 or 180 * 878 230 305 415 349 415 385
PV016, 020 or 023 860 255 403 299 406 531.5 212
PV032, 040 or 046 893 255 403 325.5 406 531.5 245
PV270 PV063, 080 or 092 200 B4 HW 954 255 403 380.5 406 531.5 306
PV140 or 180 1033 255 403 433.5 406 531.5 385
PV270 * 1134 255 403 531.5 406 531.5 510
* Combinations PV140/180 + PV140/180 and PV270 + PV270 only with splined shaft on main pump due to high torque.

PI PVplus UK.PMD RH

26 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Pump Combinations Series PV

Combinations PV / PGP511 or PGP517

M K B

D C

Main pump 2nd pump Interface main pump L* B C D* H K M

PV016, 020 or 023 PGP511 100 B4 HW 363.7-409.3 199 170,5 97.1-119.9 220 225 86.7-132.3
PGP511 415.7-461.3 211 197 106.6-129.4 245 261 86.7-132.3
PV032, 040 or 046 125 B4 HW
PGP517 451.8-490.2 211 197 122.8-161.2 245 261 122.8-161.2
PGP511 504.7-550.3 233 252 86.7-132.3 301 326 86.7-132.3
PV063, 080 or 092 160 B4 HW
PGP517 540.8-579.2 233 252 122.8-161.2 301 326 122.8-161.2
PGP511 593.7-639.3 233 305 86.7-132.3 349 415 86.7-132.3
PV140 or 180 160 B4 HW
PGP517 629.8-668.2 233 305 122.8-161.2 349 415 122.8-161.2
PGP511 733.2-778.8 258 403 86.7-132.3 406 531.5 86.7-132.3
PV270 200 B4 HW
PGP517 769.3-807.7 258 403 122.8-161.2 406 531.5 122.8-161.2
Dimensions PGP511* code H2 and PGP517* code H3
* For other dimensions of series PGP/PGM, see catalogue HY11-2500/UK, chapter 1, ‘Pumps & Motors’.

Standard Gear Pumps for combination with PV

Part Displacement Flow Weight
Model Ordering code number [cm3/U] [l/min at 1500min-1] [kg]
PGP505A0040CA1H2NJ4J4B1B1 3319111251 4 6 2.3
PGP505 PGP505A0080CA1H2NJ4J4B1B1 3319111258 8 12 3.6
PGP511A0110CA1H2NL2L1B1B1 3349111186 11 16.5 3.6
PGP511A0140CA1H2NL2L1B1B1 3349111187 14 21 3.8
PGP511A0160CA1H2NL2L1B1B1 3349111737 16 24 3.9
PGP511 PGP511A0190CA1H2NL2L1B1B1 3349111575 19 28.5 4.0
PGP511A0220CA1H2NL2L2B1B1 3349111797 22 33 4.1
PGP511A0270CA1H2NL2L2B1B1 3349111576 27 40.5 4.3
PGP511A0330CA1H2NL2L2B1B1 3349111191 33 49.5 4.6
PGP517A0230CD1H3NL3L2B1B1 3339111151 23 34.5 8.3
PGP517A0280CD1H3NL3L2B1B1 3339111484 28 42 8.5
PGP517A0330CD1H3NL3L2B1B1 3339111048 33 49.5 8.7
PGP517 PGP517A0380CD1H3NL3L2B1B1 3339111004 38 57 9.1
PGP517A0520CD1H3NL3L3B1B1 3339111152 52 78 9.5
PGP517A0700CD1H3NL3L3B1B1 3339111154 70 105 10.5
PGP350 PGP350A197EVAB2025 3239111027 83.6 125.4 25

PI PVplus UK.PMD RH

27 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Thru Drive, Shaft Load Limitations Series PV

Max. transferable torque in [Nm] for different shafts options

Shaft code PV016-023 PV032-046 PV063-092 PV140-180 PV270

D 300 550 1320 2000 2000
E 300 610 1218 2680 2680
F -- -- -- 1320 --
G -- -- -- 1640 --
K 300 570 1150 1900 2850
L 405 675 1400 2650 3980
Max. torque transmission
140 275 560 1100 1650
cap. for rear mounted pump

Important notice
The max. allowable torque of the individual shaft must
not be exceeded. For 2-pump combinations there is no
problem because PV series offers 100% thru torque. For
3-pump combinations (and more) the limit torque could
be reached or exceeded.
Therefore it is necessary to calculate the torque factor
and compare it with the allowed torque limit factor in the
table.

Pump Shaft Torque limit factor

Required: calculated torque factor
D 17700
< torque limit factor E 17700
PV016-023 K 17700
L 20130
To make the necessary calculations easier and more user D 32680
friendly it is not required to calculate actual torque re- E 36380
quirements in Nm and compare them with the shaft limi- PV032-046 K 33810
tations. The table on the right shows limit factors that in- L 40250
clude material specification, safety factors and conver- D 77280
E 72450
sion factors. PV063-092 K 67620
L 83720
The total torque factor is represented by the sum of the
D 118400
individual torque factors of all pumps in the complete pump E 158760
combination. F 78750
PV140-180 G 97650
Total torque factor of the combination K 113400
= sum of individual torque factors of all pumps L 157500
D 119000
E 159700
The torque factor of each individual pump is calculated PV270 K 170100
by multiplying the max. operating pressure p of the pump L 236250
(in bar) with the max. displacement Vg of the pump (in
cm³/rev).

Torque factor of any pump

= p x Vg

PI PVplus UK.PMD RH

28 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Compensators Dimensions Series PV

Remote pressure compensator, code FRC Remote pressure comp. with interface NG6, code FR1
Load-Sensing compensator, code FFC Load-Sensing comp. with interface NG6, code FF1
2 x M5 - 10 deep optional 10-32 UNC
All control ports G1/4 optional M 12 x 1.5; ISO 6149-1
(threads option 3 and 7)
(threads options 7 and 8) or 7/16-20 UNF (threads option 3)
31.5 Interface NG6, CETOP 03

T
31 32,5

42.5 P

74.5 2 x M5 - 10deep in
pump body (see note above)
pressure pilot port PP (code FRC)
load-sensing-port PF (code FFC) load-sensing-port PF (code FF1)
(plugged for code FR1 )

40
24

2-valve compensator, code FT1 Proportional p-Q-compensator, code FPR

(for code FPV lower valve only without interface)
interface NG6, CETOP 03
interface NG6, CETOP 03
T

80 40
40

49

50
load sensing port PF

LVDT for proportional compensator Pilot valve for horse power compensator
round connector
M 12 x 1
5 pins
69 34

pump body
pump body

Ordering code seal kit, compensator

SK PVC
Seal kit Compensator Seal
for axial
piston pump
series PV Code Seal The seal kit includes all seals for all single compensator options as
well as seals for LVDT and horse power pilot valve. For 2-valve
N NBR compensators two seal kits have to be ordered.
V FPM Spare parts lists and ordering codes for replacement compensator
E EPR valves see manual upon request.
PI PVplus UK.PMD RH

29 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Pressure Compensators Series PV

Standard pressure compensator, code F*S

The standard pressure compensator adjusts the pump
displacement according to the actual need of the system
Q
in order to keep the pressure constant.
As long as the system pressure at outlet port P is lower
than the set pressure (set as spring preload of the L P1 A
PM P L P1 A
compensator spring) the working port A of the compensa-
tor valve is connected to the case drain and the piston
area is unloaded. Bias spring and system pressure on the Standard pressure
compensator
annulus area keep the pump at full displacement. code F*S p
When the system pressure reaches the set pressure the * = pressure rating
compensator valve spool connects port P1 to A and builds S L = included
up a pressure at the servo piston resulting in a
downstroking of the pump. The displacement of the pump
is controlled in order to match the flow requirement of the
system.

Remote pressure compensator, code FRC

While at the standard pressure compensator the pres-
sure is set directly at the compensator spring, the setting PP Q
of the remote pressure compensator can be achieved by
any suitable pilot pressure valve connected to pilot port
L P1 A
PP. The pilot flow supply is internal through the valve PM P L P1 A
spool.
The pilot flow is 1 - 1.5 l/min. The pilot valve can be
Remote pres-
installed remote from the pump in some distance. That
sure compensa- p
allows pressure setting e. g. from the control panel of the tor code FRC
machine. The remote pressure compensator typically S L = included
responds faster and more precisely than the standard
pressure compensator and is able to solve instability
problems that may occur with a standard pressure com-
pensator in critical applications.
The pressure pilot valve can also be electronically con-
trolled (proportional pressure valve) or combined with a
directional control valve for low pressure standby opera-
tion.

Remote pressure compensator, code FR1

Version FR1 of the remote pressure compensator pro-
vides on its top side an interface NG6, DIN 24340 T P
(CETOP 03 at RP35H, NFPA D03). T P

This interface allows a direct mounting of a pilot valve.

Beside manual or electrohydraulic operated valves it is Q

also possible to mount complete multiple pressure cir- P1

L A
cuits directly on the compensator body. Parker offers a PM P L P1 A
variety of these compensator accessories ready to in-
stall. See pages 44-46. Remote pressure
All remote pressure compensators have a factory setting compensator with
of 15 bar differential pressure. With this setting, the interface NG6 for p
accessories
controlled pressure at the pump outlet is higher than the code FR1 = included
S L
pressure controlled by the pilot valve.

PI PVplus UK.PMD RH

30 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Load-Sensing Compensators Series PV

Load-Sensing compensator, code FFC

The load-sensing compensator has an external pilot
pressure supply. Factory setting for the differential pres-
sure is 10 bar. The input signal to the compensator is the
differential pressure at a main stream resistor. A load-
sensing compensator represents mainly a flow control for Q
PF
the pump output flow, because the compensator keeps
the pressure drop at the main stream resistor constant.
L P1 A
A variable input speed or a varying load(-pressure) has PM P L P1 A
consequently no influence on the output flow of the pump
and the speed of the actuator.
Load-Sensing
By adding a pilot orifice (Ø 0.8 mm) and a pressure pilot compensator p
valve pressure compensation can be added to the flow code FFC
control function. See the circuit diagram below, left. S L = included

Ø0.8

T P
T P

PF PF Q

L P1 A L P1 A
PM P L P1 A PM P L P1 A

Load-Sensing Load-Sensing
compensator compensator with
code FFC interface NG6 for p
external orifice and accessories
pressure pilot valve code FF1
S L S L = included

Shown above is load-sensing compensator, code FF1

with an NG6 interface on top of the control valve. That
allows direct mounting of a pilot valve for pressure com- T P
T P
pensation. This version includes the pilot orifice.
Due to the interaction of flow and pressure compensation
this package has not the "ideal" control characteristic.
The deviation is caused by the pilot valves characteristic. PF Q
If a more accurate pressure compensation is required,
the 2-valve load-sensing compensator code FT1 can L P1 A
be used. The circuit diagram of this version is shown left. PM P L P1 A

Here the interaction of the two control functions is avoided

by using two separate control valves for flow and pres- 2-valve Load-Sens.
sure compensation. compensator with
interface NG6 for p
The 2-valve compensator is equipped with an interface accessories
NG6 on the compensators top side. S L code FT1 = included

PI PVplus UK.PMD RH

31 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Horse Power Compensators Series PV

Hydraulic-mechanical horse power compensator Ordering code for the horse power option
The hydraulic-mechanical horse power compensator The first digit designates the horse power setting:
consists of a modified remote pressure compensator Code B = 3.0 kW etc. up to
(Code *L*) or of a modified load-sensing compensator Code 3 = 132.0 kW
(Code *C*) and a pilot valve. This pilot valve is integrated
The second digit designates the pilot flow source:
into the pump and is adjusted by a cam sleeve. The cam
sleeve has a contour that is designed and machined for Code L internal pilot pressure, remote pressure func-
the individual displacement and the nominal horse power tion.
setting. Code C external pilot pressure, combines horse power
At a large displacement the opening pressure (given by compensation with load-sensing compensa-
the cam sleeve diameter) is lower than at small displace- tion.
ments. This makes the pump compensate along a The third digit designates the possibility to adjust the
constant horse power (torque) curve (see diagrams on overriding pressure compensation:
opposite page). Code A comes with a top side NG6/D03 interface on
For all nominal powers of standard electrical motors the control valve to mount any suitable pilot
Parker offers a dedicated cam sleeve. The exchange of
valve or Parker pump accessories.
this cam sleeve (e. g.: to change horse power setting) can
easily be done without disassembly of the pump. Code B has a threaded pilot port Pp (G1/4) to connect
On top of that an adjustment of the horse power setting a remote pilot valve with piping.
can be done within certain limits by adjusting the preload Code C includes a pilot valve for manual pressure
of the pilot control cartridge spring . That allows an adjustment. Max. setting: 350 bar.
adjustment of a constant horse power setting for other Page 33 shows typical control characteristics and the
than the nominal speeds (1500 min-1) or for other horse available horse power settings for the different pump
powers. sizes and displacements.

Horse power comp.,

Horse power Horse power pilot flow internal
comp., pilot flow compensator, pressure pilot valve
internal interface pilot flow internal included
on top code *LB code *LC
code *LA

Horse power Horse power

compensator, comp., pilot flow
pilot flow external external for load-
for load-sensing sensing, pilot valve
code *CB included code *CC

PI PVplus UK.PMD RH

32 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Horse Power Compensators, Diagrams Series PV

Characteristic curves, horse power compensators

The diagrams shown are only valid for the following working conditions:
Speed : n = 1500 rev/min Fluid : HLP, ISO VG46
Temperature : t = 50°C Viscosity : ν = 46 mm2/s at 40°C

PI PVplus UK.PMD RH

33 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Electrohydraulic p-Q Control Series PV

Proportional displacement control, code FPV

The proportional displacement control allows the adjustment
of the pumps output flow with an electrical input signal.
The actual displacement of the pump is monitored by an LVDT
and compared with the commanded displacement in an UQ Q
electronic control module PQ0*-F00 (see opposite side). The L P1 A
command is given as an electrical input signal (0 - 10 V or 0 PM P L P1 A
Us
resp. 4 - 20 mA) from the supervising machine control. The UQ
command can also be provided by a potentiometer. The
electronic control module offers a stabilized 10 V source to
supply the potentiometer.
The electronic module compares permanently the input com- Proportional-
displacement p
mand and the actual displacement by powering the propor-
control
tional solenoid of the control valve. A deviation from the code FPV
commanded displacement leads to a modulation of the input S L = included
current to the solenoid. The control valve then changes the
control pressure (port A) until the correct displacement is
adjusted. UP T P
Version FPV of the proportional control does not provide a T P
pressure compensation. The hydraulic circuit must be pro-
tected by a pressure relief valve.
Proportional displacement control with overriding pres-
sure control, codes FPR, FPZ and FPG
UQ Q
In version FPR an additional pressure compensator valve can
override the electrohydraulic displacement control. That adds L P1 A
PM P L P1 A
pressure compensation to this control. Us UQ
The compensator valve has an NG6/D03 interface on top to
mount a pressure pilot valve. When using a proportional UP

pressure pilot valve an electro-hydraulic p/Q control can be

realized. The electronic driver modules are tuned for the valve
Proportional-
type PVACPP* to get the best performance. displacement p
The electronic control module PQ*-P00 (see page p-Q control control
analogue) contains, beside the displacement control unit, also code FPR
S L = included
the driver electronics for the a. m. proportional pressure valves.
Using ordering code FPZ and specifying the desired pilot
valve/compensator accessory, a complete multiple pressure
adjustment can be mounted in our factory (see compensator
accessories, pages 44-46) and the complete unit will be tested UP T P pP
and shipped together with the pump. Up
With ordering code FPG the proportional pressure pilot valve
T P
and a pressure transducer (Parker SCP 8181 CE) are included
with the pump control. In combination with control module
PQ0*-Q00 a closed loop pressure control of the pump outlet DP
pressure is available. Module PQ*-L00 offers an electronic DB1 DB2
horse power limiter in addition to the closed loop pressure
UQ
control.
Parker variable displacement pumps have a large servo p1 L P1 A Q
piston. That leads to a extremely robust and stable pump PM P L P1 A
Us
control. On the other hand that requires high control flows (up
to > 100 l/min). Parker has therefore chosen the 2-valve p-Q UQ
control concept, because in this case a hydraulic-mechanical
UP
compensator valve takes care of the pressure compensation
Proportional-
of the pump. That allows a very fast pressure compensation
displacement
and makes this the control unsensitive to fluid contamination. control
We see the 2-valve concept as a contribution to system and code FPG p
pressure control safety. S L = included

PI PVplus UK.PMD RH

34 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Electrohydraulic p-Q Control FP* / UP* Series PV

New version of electrohydraulic displacement and pressure control

Since shortly a new and more compact version of the p- a high „tower“ of control elements. This has caused in
Q-control for the PVplus is available. The two figures below some cases a space problem.
compare the current and the new version. The left hand Therefore the version with an „elbow“ manifold - shown in
side image shows a PV046 with compensator code the right figure - has been developed. A manifold on the
...FPG. With this ordering code the pump is equipped with compensator interface of the pump allows horizontal
an electro hydraulic displacement control and an mounting of all control and pilot elements without stacking.
overriding closed loop pressure control. The compensator ordering code changes from ...FPG to
In version ...FPG the sandwich style mounting of the ...UPG for this new version (see ordering code
compensator valves, pilot valve and transducer leads to “electrohydraulic compensators“ on page 6).

PV046R1K1T1NFPG PV046R1K1T1NUPG
Pump with electrohydraulic displacement and closed loop Pump with electrohydraulic displacement and closed
pressure control loop pressure control with elbow manifold

Beside the more compact and less vibration sensitive arrangement the elbow manifold version has more
advantages:
All elements (compensator valves, pilot valve, pressure The valve bodies of the compensator valves are standard
sensor) can be removed and serviced separately. versions and no longer the special sandwich style versions
(simplified logistics).

PI PVplus UK.PMD RH

35 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Electrohydraulic p-Q Control FP* Series PV

Dimensions
Axial piston pump series PV with p-Q-control,
compensator ordering code ...FPG (closed loop pressure
control)

Note
For version without pressure sensor (open loop pressure
control) dimensions G and H are shorter by 40 mm and
dimension D2 is not applicable.

Size Dimension [mm] A B C D D1 D2 E F G H K L N

BG1 PV016-PV023 66 132 85 122 126.5 171.5 256.5 197.5 174.1 396.5 174 80 26.5
BG2 PV032-PV046 78 156 85 122 126.5 171.5 256.5 227.0 174.1 421.5 199 92 33.0
BG3 PV063-PV092 102 204 85 122 126.5 171.5 256.5 287.0 174.1 475.5 253 118 40.0
BG4 PV140-PV180 100 200 85 122 126.5 171.5 256.5 350.0 174.1 525.5 303 145 58.0
BG5 PV270 125 250 85 122 126.5 171.5 256.5 472.5 174.1 582.5 360 176 85.5

PI PVplus UK.PMD RH

36 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Electrohydraulic p-Q Control UP* Series PV

Dimensions
Axial piston pump series PV with p-Q-control,
compensator ordering code ...UPG (closed loop pressure
control).

Size Dimension [mm] A B C D E F G H K L M N P R

BG1 PV016-PV023 66 132 94.5 149.5 243.9 197.5 91.1 313.3 174 80 305 26.5 134 234
BG2 PV032-PV046 78 156 94.5 149.5 243.9 227.0 91.1 438.3 199 92 328 33.0 134 234
BG3 PV063-PV092 102 204 94.5 149.5 243.9 287.0 91.1 392.3 253 118 381 40.0 134 234
BG4 PV140-PV180 100 200 94.5 149.5 243.9 350.0 91.1 442.3 303 145 426 58.0 134 234
BG5 PV270 125 250 94.5 149.5 243.9 472.5 91.1 499.3 360 176 521 85.5 134 234

PI PVplus UK.PMD RH

37 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Electronic Module PQ* (analogue) Series PV

The electronic modules to power the displacement con-

trol and the pressure control are snap-on type modules.
They can be mounted on installation rails according to EN
50022. A card holder is not required.
The modules have potentiometers to adjust up and down
ramps (ramp time up to 5s) and a min. and max. adjust-
ment for optimum resolution and sensitivity as required
by the application.
They comply with the latest legal requirements and
confirm to European law. They are EMC approved and
correspond to the CE guidelines.

Electronic modul PQ0*-P00 to operate the p-Q control for PV pumps

Ordering code analogue electronic module

PQ 00

Pump Pump Module Design

amplifier variation variation series

Code Pump variation Code Variation

01 PV 016/020/023 F flow control only
02 PV 032/040/046 P flow control and pressure adjustment
03 PV 063/080/092 Q flow and pressure control
04 PV 140/180 L flow and pressure control with horse
05 PV 270 power limitation

NOTE!
The electronic modules are not included in the pump More technical information on these modules can be found in
compensator. Please order separately. catalogue HY11-2500/UK, chapter 10, ‘Electronics’.

Technical data Diagrams

Minimum control pressure required 15 bar

(at internal pressure supply
= minimum system pressure)
Repeatability ± 0.75 %

Proportional flow compensator

(solenoid):

- nominal voltage 16 V
- environmental temperature 50 °C
- duty cycle 100 %
- protection class IP54
- connector ISO 4400

Inductive position feedback (LVDT): Response times

- supply voltage 18 to 36 VDC Size TA [ms] TR [ms]
- current requirement <50 mA
3.5 to 11.5 VDC PV023 50 50
- output voltage
- environmental temperature 0 to 50 °C PV046 70 70
- load to output signal > 5 kOhm (short circuit pro- PV092 90 90
tected) PV180 150 150
- connector round connector M12x1.5 pin PV270 200 200

PI PVplus UK.PMD RH

38 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Electronic Module PQDXXA (digital) Series PV

The digital control module code PDDXXA-Z00 is also

designed for rail mounting like the analog modules.

Features
• Digital control circuit
• Parameter setting via RS-232 interface
• All settings (ramps, MIN/MAX, control parameters) can
be stored digitally and recalled from a PC to duplicate
settings to other modules
• Ramp time up to 60 seconds • Covers all functions: displacement control, displace-
• Compatible to the relevant european EMC specificati- ment control with open loop pressure control, displace-
ons ment control with closed loop pressure control and dis-
• Easy to use PC based setup software placement control with closed loop pressure control
• Covers all displacements from 16 to 270 cm³/rev and electronic horse power limitation.
Ordering code
PQD XX A Z00
Digital control For all frame Version A Option
module for p-Q sizes series PV
Please order the
control
“interface cable to PC“
Note separately.
More technical information on these modules can be found in Ordering code:
catalogue HY11-2500/UK, chapter 10, ‘Electronics’. PQDXXA-KABEL

Technical data Programming software

The programming of the p-Q-control module is done in an
Mounting style Snap-on mounting for EN50022
rail
easy to learn mode. To select the pump model and size
Body material Polycarbonate
and to set the control paramters the program ProPVplus
Inflammation class V2...V0 acc. UL 94
must be started. This program runs under WINDOWS® 95
Mounting position any
and higher.
Env. temperature range [°C] -20...+55
The latest version of this software can be downloaded at
Protection class IP 20 acc. DIN 40 050
the following internet address:
Weight [g] 160 http://www.parker.com/euro_hcd
Duty ratio [%] 100 The software offers the following features:
Supply voltage [V] 18...30VDC, ripple <5% eff. A TERMINAL window to set or read out the control param-
Rush in current [A] 22 for 0.2 ms eters of the module. Settings as well as comments
Current consumption [A] < 4 for p/Q-control entered in the terminal window can be stored also in RTF-
< 2 for Q-control format (opens e. g. under WORD or other text editors)
Resolution [%] 0.025 (horse power 0.1) A MONITOR window allows to display process variables
Interface RS232C, 9600 baud, 3.5 mm cinch in numerical format.
EMC EN 50 081-2, EN 50 082-2 An OSZILLOSKOP window displays process variables as
Connctors Screw terminals 0.2...2.5 mm² curves. The oscilloscope offers a start - stop function. The
plug in style images can be saved and stored e. g. for import into other
Cables [mm²] 1.5 (AWG 16) programs.
overall braid shield, for supply and Features
solenoid connection 0.5 mm²
• Display and documentation of parameter sets
(AWG 20) overall braid shield, for
sensor and command signal con- • Save ond reload of optimized parameter sets
nections • Offers oscilloscope function for easy performance evalu-
Max. cable length [m] 50 ation and optimization
• Pre-optimized parameter sets for all PVplus piston pump
For programming the module via PC, an interface cable is needed, to • Sizes already in E2PROM memory
order seperately.

PI PVplus UK.PMD RH

39 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Pump Accessory PVAPVV* Series PV

Preload valve for proportional displacement control, Preload valve PVAPVV*

code PVAPVV*
An alternative solution is the use of a direct operated Drain port L, G1/4“ Gage port p 1, G1/4“
preload valve. The preload valve is offered in a manifold (preloaded pressure,
for direct mounting to the pressure port of the pump. covered)

The opening pressure of the valve is set to approx. 20 bar.

At 30 bar load pressure the valve is fully open (pressure
drop <1 bar).
The ordering code for the preload valve is PVAPVV*. Note: All auxiliary
Therefore * stands for the frame size of the pump (thread, manifolds can
port and seal material option). also be supplied in
US-version (UNC
threads and UNF
por ts) and with
ports according to
ISO 6149.

Flanged ports ISO 6162: DN, Gage por t p 2 , G1/4“

PN; fits to PV frame size BG; (outlet pressure, cove-
threads: M red)

Dimensions preload valve PVAPVV*

Dimension BG1 BG2 BG3 BG4 BG5
H [mm] 110 110 110 110 130
B [mm] 92 92 100 100 154
T [mm] 80 80 92 92 105
L 2) [mm] 120 120 140 140 160
T1 [mm] 116 116 137 137 150
for size PV016 - 023 PV032 - 046 PV063 - 092 PV140 - 180 PV270
DN [mm] 19 (3/4“) 25 (1“) 32 (1 1/4“) 32 (1 1/4“) 38 (1 1/2“)
PN [bar] 400 400 400 400 400
M M10 M12 M12 (M14*) M12 (M14*) M16
valve insert DIN E16 DIN E16 DIN E25 DIN E25 DIN E32
Qnominal [l/min] 160 160 300 300 550
2)
* optional for PV063 - PV180, thread option 4; L = clamping length for bolts M

Hydraulic circuit FPR/UPR control and preload manifold

Proportional displace-
ment control with pres-
sure compensation
and preload valve

PI PVplus UK.PMD RH

40 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Pump Accessory PVAPSE* Series PV

Quick unload manifold for proportional pump control, code Quick unload manifold
PVAPSE*
When working with a proportional pressure control on variable Flange port ISO Control port pP, G1/ Gage port MpP,
displacement pumps, pressure decrease can be slow. When 6162, DN, PN; fits 4“ (to compensa-
the pump strokes to deadhead, there is no active pressure relief. to PV frame size tor)
To achieve a response similar to a valve controlled system, the BG; thread M
quick unload manifold can be mounted to the pump outlet.
This manifold includes a cartridge valve with a 4 bar spring
preload. The pilot pressure supply for the compensator valve is
passing this cartridge valve and creates a pressure drop across Also available
the poppet. At normal working conditions this pressure drop in US-version
does not exceed 3 bar and the poppet stays closed. In a dynamic (UNC threads
and UNF ports)
response situation the pressure drop can exceed 4 bar and the
and with ports
cartridge actively reduces the system pressure acoording to according to
the setting of the proportional pilot valve. ISO 6149.
As the pilot pressure is fed through the quick unload manifold,
the compensator needs no orifice in the spool. Ordering code
for the proportional displacement and pressure control for
Return port T, thread G; Max. pressure pilot valve
combination with the quick unload manifold is FPS for pressure
compensation and FPT for closed loop pressure control
(pressure transducer and proportional pressure pilot valve
included).
Dimensions quick unload manifold PVAPSE*
Dimension BG1 BG2 BG3 BG4 BG5
B [mm] 110 110 110 110 154
H [mm] 92 92 100 100 120
T [mm] 80 80 92 92 105
B1 [mm] 150 150 150 150 199
H1 [mm] 133 133 141 141 143
for size PV016 - 023 PV032 - 046 PV063 - 092 PV140 - 180 PV270
DN [mm] 19 (3/4“) 25 (1“) 32 (1 1/4“) 32 (1 1/4“) 38 (1 1/2“)
PN [bar] 400 400 400 400 400
M M10 M12 M12 (M14*) M12 (M14*) M16
valve insert DIN E16 DIN E16 DIN E16 DIN E16 DIN E25
Qnominal [l/min] 160 160 160 160 300
G (port T) 1/2“ 1/2“ 1/2“ 1/2“ 3/4“
* optional for PV063 - PV180, thread option 4
Hydraulic circuit FPS/UPS control with quick unload manifold

Proportional displace-
ment control with pres-
sure compensation
and quick unload mani-
fold

PI PVplus UK.PMD RH

41 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Pump Accessory PVAPVE* Series PV

Preload and quick unload manifold, code PVAPVE*

The combination of the preload and the quick unload (Ps) which is connected to the system side of the preload
function into one manifold can be ordered under the code valve.
PVAPVE*. This manifold is also designed for direct pump The ordering code for this proportional displacement control
outlet mounting. option is FPP for pressure compensation and FPE for
To maintain a secure function under all conditions the closed loop pressure control.
pressure compensator requires an external sensing line

Preload valve
Max. pressure
pilot valve

Cover and insert Gage port Mp1,

DIN E NG2 G1/4“
quick unload valve

Also available in
US-version (UNC
threads and UNF
por ts) and with
Gage port Mp2,
ports according to
G1/4“
ISO 6149.

Return port TE,

thread G

Optional outlet P2,

SAE port DN
thread G2

Gage port MpP, Pilot port Pilot port

G1/4“ pS, G1/4“ pP, G1/4“

Flange ports ISO 6162; DN, PN; fit to PV, frame size BG; thread M

Dimensions preload and quick unload manifold PVAPVE*

Dimension BG1 BG2 BG3 BG4 BG5
B [mm] 145 145 175 175 210
H [mm] 113 113 135 135 160
T [mm] 80 80 92 92 105
L [mm] 120 120 140 140 160
H1 [mm] 153 153 175 175 205
T1 [mm] 116 116 137 137 150
for size PV016 - 023 PV032 - 046 PV063 - 092 PV140 - 180 PV270
DN [mm] 19 (3/4“) 25 (1“) 32 (1 1/4“) 32 (1 1/4“) 38 (1 1/2“)
PN [bar] 400 400 400 400 400
M M10 M12 M12 (M14*) M12 (M14*) M16
valve insert NG1 DIN E16 DIN E16 DIN E25 DIN E25 DIN E32
Qnominal [l/min] 160 160 300 300 550
valve insert NG2 DIN E16 DIN E16 DIN E16 DIN E16 DIN E25
Qnominal [l/min] 160 160 160 160 300
G (port TE) 1/2“ 1/2“ 3/4“ 3/4“ 3/4“
G2 (opt. outlet) 3/4“ 1“ 1 1/4“ 1 1/4“ 1 1/2“
* optional for PV063 - PV180, thread option 4

PI PVplus UK.PMD RH

42 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Pump Accessory PVAPVE* / Ordering Code Series PV

Hydraulic circuit FPS/UPS control with preload and quick unload manifold

Proportional displace-
ment control with pres-
sure compensation
and preload plus quick
unload manifold

Ordering code pump accessories

PVAP
Accessories for axial Function Frame Thread Seal
piston pump, PV size option
series, pressure port
mounting

Code Function Code Seal

VV Preload manifold N NBR
Quick unload V FPM
SE manifold E EPDM
Preload and
VE quick unload
Code Ports1) Threads2)
manifold
1 BSPP Metric
3 UNF UNC
Code Size 43) BSPP Metr. M14
1 PV016-023 7 ISO 6149 UNC
2 PV032-046 8 ISO 6149 Metric
3 PV063-092 1)
Drain, gage and control ports
4 PV140-180 2)
Mounting threads
5 PV270 3)
For PV063-PV180 only: pressure
port 1 1/4" with M14 instead of M12

PI PVplus UK.PMD RH

43 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Hydraulic Circuit / Ordering Examples Series PV

Ordering Examples
Example 1 Example 2
PV pump with fast response remote pressure control, Same pump, accessories not fitted:
relief valve with 2 pressure stages, electrical pressure PV * * * * * * * * FR1; 1 = PVAC2PCMNSJW35
selection, nitrile seals, spindle adjustment, 24 VDC sole- Example 3
noid, accessories fitted: Usable for horsepower control and proportional volume
PV * * * * * * * * FRZ; Z = PVAC2PCMNSJW35 control, too.
PV * * * * * * * * FRZ; Z = PVAC2PCMNSJW35

Schematics PVAC1P* Schematics PVAC1E*

Schematics PVAC2P* Schematics PVAC2E

PI PVplus UK.PMD RH

44 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Ordering Code / Dimensions Series PV

PV AC 35
For Accessories Function Mounting Threads Seals Adjustment Solenoid Solenoid Nominal Design
PV pump for bolts acces- pressure series
series compensa- sories 350 bar (not required
tors 1) for order)

Code Function Code Threads Code Solenoid accessories

1P Max. pressure relief M metric omit For function 1P
S SAE / UNC Conduit box
1 pressure, C
1E electrical unloading with free wires
Code Seals
2 pressures, DIN plug socket
2P N NBR W without plug
electrical selection
V FPM
2 pressures + stands
2E electrical selection E EPR
Code Solenoid voltage
low pressure default
Code Mounting bolts Code Adjustment omit For function 1P
2 pressures + stands
2M electrical selection C For single compensators type R or F Spindle Y 110V/50Hz - 120V/60Hz
stand by default T For 2-valve-compensator type T S with lock nut T 220V/50Hz - 240V/60Hz
S Without bolts 2) L DIN lock J 24V DC
P For code FP* 1)
Other pressures on request.
U For code UP* 2)
Mounting bolts code “S“ only in combination with thread option “M“.

For spare parts and replacement kits see manual upon request.
Please order plugs separately. See accessories in catalogue HY11-2500/UK, chapter 2, ‘DC Valves’.

Dimensions
PVAC1P* PVAC1E*
DC solenoid 205
AC solenoid 190
Adjustment
Code S

Adjustment
Code L

Pressure relief valve mounted on 2-valve pressure-flow compensator Pressure relief valve, electrical unloading, mounted on compensator
type T type R or F

PVAC2P* PVAC2E*/2M*
DC solenoid 205 DC solenoid 241
AC solenoid 190 AC solenoid 211

High Low High Low

pressure pressure pressure pressure

2-pressure relief valve, electrical selection, mounted on compensator 2-pressure relief valve, electrical selection and unloading, mounted on
type R or F compensator type R or F
PI PVplus UK.PMD RH

45 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Accessories Series PV

Ordering code proportional pressure control valve

PV AC PP
Pump Accessories Prop. Mounting Thread Seal Nominal Design
series PV for controller pressure bolts option pressure series
valve (not required
for order)

Code Mounting bolts/ Code Nominal pressure

ports 35 350 bar
C For single controller type R or F 42 420 bar
T For double valve contr. type T
S Without bolts* Code Seal
D For code FPD, FPS, FPP Code Thread option N NBR
P For code FPG, FPE, FPT * Mounting bolts code “S“ M Metric V FPM
only in combination with
U For code UP* S SAE / UNC E EPDM
thread option “M“

Proportional pressure control valve

Proportional pressure pilot valves of series PVACPP* are They allow an infinite electronic adjustment of the pumps
powered by external electronic modules (e. g. PCD00*, compensating pressure. The different pressure ratings
see catalogue HY11-2500/UK, chapter10, ‘Electronics’). come with different control orifices in the pilot valve.

Schematic PVACPP* Dimensions PVACPP*

PI PVplus UK.PMD RH

46 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Safety Manifolds PVAPS* Series PV

System protection through new manifolds for pump

safety
These manifolds for pumps prevent hydraulic systems
from inadmissible pressure rises. In addition to pressure
limiting types, modules with integrated check valves which
allow several pumps to co-operate in a hydraulic circuit
are available.
The product range also includes electrically unloadable
manifolds with or without check valves.
The Parker manifolds for pump safety match all pumps
with SAE flange bearings from SAE 3/4 to 1 1/2 -6000
PSI. The modules can be mounted directly onto the pump
flange, rendering expensive piping and assembly super-
fluous.

• Protection against inadmissible increase in hydraulic systems

• Variety of functions - pressure relief with check valve for pump combinations, electrical unloading with/without
check valve
• Direct mounting on pump pressure port - extra piping and assembly unnecessary
• Pressure-free pump start and bypass function
• Suitable for pump ports SAE 3/4 to SAE 1 1/2 6000 PSI

Pump size Max. flow [l/min] Min/Max pressure DB [bar] Min. circulation pressure DCV [bar]
PV016 / PV023 24 / 34,5 7 / 350 5
PV032 / PV046 48 / 69 5 / 350 5
PV063 / PV092 94.5 / 138 6 / 350 5
PV140 / PV180 210 / 270 6 / 350 5
PV270 405 6 / 350 5
Please note that a pressure increase by more than approx. 20% of the adjusted pressure is possible by increasing volume flow.

Ordering code
PVAP
Accessories for axial Function Size Thread Seal
piston pump, PV series, option
pressure port mounting

Code Function Code Seal

N NBR
Pressure relief V FPM
SV E EPDM
valve Code Size
PV016 – PV023
1
Pressure relief (SAE3/4–6000PSI)
SR valve with check Code Ports1) Threads2)
PV032 – PV046
valve 2
(SAE1–6000PSI) 1 BSPP Metric
3 UNF UNC
Pressure relief PV063 – PV092
3 43) BSPP Metr. M14
valve with check (SAE11/4–6000PSI)
ST 7 ISO 6149 UNC
valve, electr.
8 ISO 6149 Metric
unloading PV140 – PV180
4 1)
Drain, gage and control ports
(SAE11/4–6000PSI)
2)
Pressure relief Mounting threads
3)
SS valve with electr. PV270 For PV063-PV180 only: pressure
5 port 1 1/4" with M14 instead of M12
unloading (SAE11/2–6000PSI)

PI PVplus UK.PMD RH

47 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Safety Manifolds PVAPS* Series PV

Option SV, pump safety manifold with pressure relief valve

Size b1 b2 b3 b4 h1 h2 h3 t M P 6000 PSI T O-ring

PVAPSV11 27 85 27.4 67 40 90 22.5 45 G 1/4 G/SAE 3/4 G 1/2 2-214
PVAPSV21 32 95 30 73.2 45 100 22.5 45 G 1/4 SAE 1 G 3/4 2-219
PVAPSV31 37 125 27 94.3 60 120 30 60 G 1/4 SAE 1 1/4 G 1 1/4 2-222
PVAPSV41 37 125 31 94.3 60 120 30 60 G 1/4 SAE 1 1/4 G 1 1/4 2-222
PVAPSV51 50 145 36 112.4 60 125 35 70 G 1/4 SAE 1 1/2 G 1 1/2 2-225
Mounting bolts not included in delivery.
PI PVplus UK.PMD RH

48 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Safety Manifolds PVAPS* Series PV

Option SR, pressure relief with check valve

Size b1 b2 b3 b4 b5 h1 h2 h3 h4 t1 t2 d1 d2 M P 6000 PSI T O-ring

PVAPSR11 63,5 85 29 67,5 22,5 42 93 70 41 89 90 11 17 G 1/4 G/SAE 3/4 G 1/2 2-214
PVAPSR21 75 110 30,5 88,5 26 50 104 68 50 75 90 13 20 G 1/4 SAE 1 G 3/4 2-219
PVAPSR31 95,5 140 31 110,4 37 60 120 90 60 105 120 13 20 G 1/4 SAE 1 1/4 G 1 1/4 2-222
PVAPSR41 95,5 140 31 110,4 37 60 120 90 60 105 120 13 20 G 1/4 SAE 1 1/4 G 1 1/4 2-222
PVAPSR51 115 160 36,4 126 40 60 130 95 60 115 135 18 26 G 1/4 SAE 1 1/2 G 1 1/2 2-225
Mounting bolts included in delivery.
PI PVplus UK.PMD RH

49 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Safety Manifolds PVAPS* Series PV

Option ST, pressure relief with check valve, electr. unloading with/without check valve

Size b1 b2 b3 b4 b5 h1 h2 h3 h4 h5 t1 t2 t3 d1 d2 M P 6000 PSI T O-ring

PVAPST11 63.5 90 29 72.5 22.5 41 90 72 70 41 89 90 8 11 17 G 1/4 G/SAE 3/4 G 1/2 2-214
PVAPST21 74.5 110 50 80 26 50 100 124 70 50 90 105 96.5 13 20 G 1/4 SAE 1 G 3/4 2-219
PVAPST31 95.5 140 50 99 37 60 120 99.1 96 60 125 140 82.5 13 20 G 1/4 SAE 1 1/4 G 1 1/4 2-222
PVAPST41 95.5 140 50 99 37 60 120 99.1 96 60 125 140 82.5 13 20 G 1/4 SAE 1 1/4 G 1 1/4 2-222
PVAPST51 115 164 50 123 40 60 130 95.1 96 60 120 140 81 18 26 G 1/4 SAE 1 1/2 G 1 1/2 2-225
Mounting bolts included in delivery.
PI PVplus UK.PMD RH

50 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Safety Manifolds PVAPS* Series PV

Option SS, pressure relief valve with electr. unloading

Size b1 b2 b3 b4 h1 h2 h3 h4 t1 d1 M P 6000 PSI T O-ring

PVAPSS11 27 100 33 82 40 100 79 23 46 11 G 1/4 G/SAE 3/4 G 1/2 2-214
PVAPSS21 29 110 88 80.5 45 100 72 34 75 13 G 1/4 SAE 1 G 3/4 2-219
PVAPSS31 34 130 138 89.5 55 110 64 43 90 13 G 1/4 SAE 1 1/4 G 1 1/4 2-222
PVAPSS41 34 130 138 89.5 55 110 64 43 90 13 G 1/4 SAE 1 1/4 G 1 1/4 2-222
PVAPSS51 35 140 138 99.5 57 120 59 43 90 17 G 1/4 SAE 1 1/2 G 1 1/2 2-225
Mounting bolts not included in delivery.
PI PVplus UK.PMD RH

51 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Accessories Series PV

Bell housing, coupling and foot flange

Can be purchased at:

Raja or KTR
Rahmer + Jansen GmbH Kupplungstechnik GmbH
Vorthstr. 1 Rodder Damm
58775 Werdohl, Germany 48432 Rheine, Germany
Tel.: (+2392) 5090, fax: (+2392) 4966 Tel.: (+5971) 798-0, fax: (+5971) 798443

Welding flange * Threaded flange *

Can be purchased at:

Parker Hannifin GmbH
Tube Fittings Division
Am Metallwerk 9
33659 Bielefeld, Germany
Tel.: (+521) 4048-0, fax: (+521) 4048280

SAE-flange connections, pipe connection in accordance to DIN 2353

Elbow SAE-flange connection WFS * Straight SAE-flange connection GFS *

Can be purchased at:

Parker Hannifin GmbH
Tube Fittings Division
Am Metallwerk 9
33659 Bielefeld, Germany
Tel.: (+521) 4048-0, fax: (+521) 4048280
* For further information about flanges see catalogue No. 4039/UK „Pressure Hydraulic Flanges“ (on request)
PI PVplus UK.PMD RH

52 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
General Installation Information Series PV

Fluid recommendations Drain port

Premium quality hydraulic mineral oil fluids are recom- Compensation may cause short-term (20 to 30 ms) flow
mended, like H-LP oils to DIN 51524, part 2. The viscosity increase, e.g. 30 l/min (PV 016 to 023), 40 l/min (PV 032
range should be 25 to 50 mm2/s (cSt) at 50 0C. to 046), 60 l/min (PV 063 to 092),80 l/min (PV 140 to 180)
Normal operating viscosity range between 12 and 100 and/or 120 l/min (PV270). Please consider for dimen-
mm2/s (cSt). Maximum start-up viscositiy is 320 mm2/s sioning.
(cSt). Operating temperature -10 to + 70 0C. Drain line
For other fluids such as phosphoric acid esters or for The drain line must lead directly to the reservoir without
other operating conditions consult your Parker represen- restriction. The drain line must not be connected to any
tative for assistance. other return line. The end of the drain line must be below
Seals the lowest fluid level in the reservoir and as far away as
NBR (nitrile) seals are used for operation with hydraulic possible from the pump inlet line. This ensures that the
fluids based on mineral oil. For synthetic fluids, as per- pump does not empty itself when not in operation and that
haps phosphoric acid esters, Fluorocarbon seals are hot aireated oil will not be recirculated.
required. Consult your Parker representative for assis- For the same reason, when the pump is mounted inside
tance. the reservoir, the drain line should be arranged in such a
way that a siphon is created. This ensures that the pump
Filtration
is always filled with fluid. The drain pressure must not
For maximum pump and system component functionability exceed 2 bar. Drain line length should not exceed 2
and life, the system should be protected from contamina- metres. Minimum diameter should be selected according
tion by effective filtration. to the port size and a straight low pressure fitting with
Fluid cleanliness should be in accordance with ISO maximised bore should be used.
classification ISO 4406:1999. The quality of filter ele- Shaft rotation and alignment
ments should be in accordance with ISO standards.
Pump and motor shafts must be aligned within 0.25mm
Minimum requirement for filtration rate x (mm): T.I.R. maximum. A floating coupling must be used.
General hydraulic systems for satisfactory operation: Bellhousings and couplings can be ordered at manufac-
Class 20/18/15, to ISO 4406:1999 turers listed in this catalogue. Please follow the coupling
x = 25 µm (ß25 ≥ 75) to ISO 4572 manufacturer's installation instructions. Consult your
Parker representative for assistance on radial load type
Hydraulic systems with maximised component life and drives.
functionability:
Start up
Class 18/16/13, to ISO 4406:1999
Prior to start up, the pump case must be filled with
x = 10 µm (ß10 ≥ 75) to ISO 4572 hydraulic fluid (use case drain port). Initial start up should
It is recommended to use return line or pressure filters. be at zero pressure with an open circuit to enable the
Parker Filter Division offers a wide range of these filters pump to prime. Pressure should only be increased once
for all common applications and mounting styles. The use the pump has been fully primed.
of suction filters should be avoided, especially with fast
response pumps. Bypass filtration is a good choice for
best filter efficiency. Attention: Check motor rotation direction.
For more details see installation manual HY11-PVI016.
Installation and mounting
Horizontal mounting: Outlet port side or top. Inlet port side
or bottom, drain port always uppermost.
Vertical mounting: Shaft pointing upwards.
Install pump and suction line in such a way that the
maximum inlet pressure never exceeds 0.8 bar absolute.
The inlet line should be as short and as straight as
possible. A short suction line cut to 450 is recommended
when the pump is mounted inside the reservoir, to im-
prove the inlet conditions. All connections to be leak-free,
as air in the suction line will cause cavitation, noise, and
damage to the pump.

PI PVplus UK.PMD RH

53 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Notes Series PV

PI PVplus UK.PMD RH

54 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3243/UK Axial Piston Pump
Notes Series PV

PI PVplus UK.PMD RH

55 Parker Hannifin GmbH

Hydraulic Controls Division
Kaarst, Germany
Hydraulics Group
Sales Offices
Europe International
Austria Italy Australia
Wiener Neustadt Corsico (MI) Castle Hill
Tel: +43 (0)2622 23501 Tel: +39 02 45 19 21 Tel: +61 (0)2-9634 7777
Fax: +43 (0)2622 66212 Fax: +39 02 4 47 93 40 Fax: +61 (0)2-9899 6184

Belgium The Netherlands Canada

Nivelles Oldenzaal Milton, Ontario
Tel: +32 (0)67 280 900 Tel: +31 (0)541 585000 Tel: +1 905-693-3000
Fax: +32 (0)67 280 999 Fax: +31 (0)541 585459 Fax: +1 905-876-0788

Czech Republic Norway China

Prague Ski Beijing
Tel: +420 2 830 85 224 Tel: +47 64 91 10 00 Tel: +86 10 6561 0520
Fax: +420 2 830 85 360 Fax: +47 64 91 10 90 Fax: +86 10 6561 0526

Denmark Poland Asia Pacific Group

Ballerup Warsaw Hong Kong, Kowloon
Tel: +45 4356 0400 Tel: +48 (0)22 863 49 42 Tel: +852 2428 8008
Fax: +45 4373 8431 Fax: +48 (0)22 863 49 44 Fax: +852 2425 6896

Finland Portugal India

Vantaa Leca da Palmeira Mumbai
Tel: +358 (0)9 4767 31 Tel: +351 22 9997 360 Tel: +91 22 7907081
Fax: +358 (0)9 4767 3200 Fax: +351 22 9961 527 Fax: +91 22 7907080

France Slovakia Japan

Contamine-sur-Arve Ref. Czech Republic Tokyo
Tel: +33 (0)450 25 80 25 Tel: +(81) 3 6408 3900
Fax: +33 (0)450 03 67 37 Spain Fax: +(81) 3 5449 7201
Madrid
Germany Tel: +34 91 675 73 00 Latin America Group
Kaarst Fax: +34 91 675 77 11 Brazil
Tel: +49 (0)2131 4016 0 Tel: +55 12 3954-5100
Fax: +49 (0)2131 4016 9199 Sweden Fax: +55 12 3954-5266
Spånga
Hungary Tel: +46 (0)8 597 950 00 South Africa
Budapest Fax: +46 (0)8 597 951 10 Kempton Park
Tel: +36 (06)1 220 4155 Tel: +27 (0)11-961 0700
Fax: +36 (06)1 422 1525 United Kingdom Fax: +27 (0)11-392 7213
Warwick
Ireland Tel: +44 (0)1926 317 878 USA
Dublin Fax: +44 (0)1926 317 855 Cleveland (industrial)
Tel: +353 (0)1 293 9999 Tel: +1 216-896-3000
Fax: +353 (0)1 293 9900 Fax: +1 216-896-4031
Lincolnshire (mobile)
Tel: +1 847-821-1500
Fax: +1 847-821-7600

Parker Hannifin is the world’s premier supplier of motion and control systems
and solutions, with sales and manufacturing facilities throughout the world. For
product information and details of your nearest Parker sales office, visit us at
www.parker.com or call free on 00800 2727 5374.

Catalogue HY11-3243/UK
09/04

© Copyright 2004
Parker Hannifin Corporation
All rights reserved.