336D L Excavators M4T00001-UP (MACHINE) POWERED BY C9 Engine(SEBP...

Página 1 de 5

Previous Screen

Welcome: u060jcc

Product: EXCAVATOR
Model: 336D L EXCAVATOR M4T00002
Configuration: 336D L Excavators M4T00001-UP (MACHINE) POWERED BY C9 Engine

Operation and Maintenance Manual

330D and 336D Excavators
Media Number -SEBU8046-10 Publication Date -01/02/2013 Date Updated -28/02/2013

i05269551

Maintenance Interval Schedule

SMCS - 7000

Ensure that all safety information, warnings, and instructions are read and understood before any
operation or any maintenance procedures are performed.

The user is responsible for the performance of maintenance. All adjustments, the use of proper
lubricants, fluids, filters, and the replacement of components due to normal wear and aging are
included. Failure to adhere to proper maintenance intervals and procedures may result in
diminished performance of the product and/or accelerated wear of components.

Use mileage, fuel consumption, service hours, or calendar time, WHICH EVER OCCURS FIRST,
in order to determine the maintenance intervals. Products that operate in severe operating
conditions may require more frequent maintenance. Refer to the maintenance procedure for any
other exceptions that may change the maintenance intervals.

Note: Before each consecutive interval is performed, all maintenance from the previous interval
must be performed.

Note: If Cat HYDO Advanced hydraulic oils are used, the hydraulic oil change interval is
extended to 3000 hours. S·O·S services may extend the oil change even longer. Consult your Cat
dealer for details.

When Required
Air Conditioner/Cab Heater Filter (Recirculation) - Inspect/Replace
Battery - Recycle
Battery or Battery Cable - Inspect/Replace
Bucket Linkage - Inspect/Adjust
Bucket Tips - Inspect/Replace
Bucket Tips - Inspect/Replace
Cab Air Filter (Fresh Air) - Clean/Replace
Circuit Breakers - Reset
Engine Air Filter Primary Element - Clean/Replace

https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 09/06/2014
336D L Excavators M4T00001-UP (MACHINE) POWERED BY C9 Engine(SEBP... Página 2 de 5

Engine Air Filter Secondary Element - Replace

Ether Starting Aid Cylinder - Replace
Film (Product Identification) - Clean
Fuel System - Prime
Fuses - Replace
Oil Filter - Inspect
Radiator Core - Clean
Track Adjustment - Adjust
Window Washer Reservoir - Fill
Window Wiper - Inspect/Replace
Windows - Clean

Every 10 Service Hours or Daily for First 100 Hours

Boom and Stick Linkage - Lubricate
Bucket Linkage - Lubricate

Every 10 Service Hours or Daily

Cooling System Coolant Level - Check
Engine Oil Level - Check
Fuel System Water Separator - Drain
Fuel Tank Water and Sediment - Drain
Hydraulic System Oil Level - Check
Indicators and Gauges - Test
Seat Belt - Inspect
Track Adjustment - Inspect
Travel Alarm - Test
Undercarriage - Check

Every 10 Service Hours or Daily for Machines Used in Severe Applications

Bucket Linkage - Lubricate

Every 50 Service Hours or Weekly

Bucket Linkage - Lubricate
Quick Coupler - Lubricate

Every 100 Service Hours or 2 Weeks

Boom and Stick Linkage - Lubricate

Every 100 Service Hours or 2 Weeks for Machines Used in Severe Applications
Boom and Stick Linkage - Lubricate

Initial 250 Service Hours

Engine Valve Lash - Check
Final Drive Oil - Change
Hydraulic System Oil Filter (Case Drain) - Replace
Hydraulic System Oil Filter (Pilot) - Replace

https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 09/06/2014
336D L Excavators M4T00001-UP (MACHINE) POWERED BY C9 Engine(SEBP... Página 3 de 5

Hydraulic System Oil Filter (Return) - Replace

Swing Drive Oil - Change

Every 250 Service Hours

Cooling System Coolant Sample (Level 1) - Obtain
Engine Oil Sample - Obtain
Final Drive Oil Sample - Obtain

Every 250 Service Hours or Monthly

Belt - Inspect/Adjust/Replace
Condenser (Refrigerant) - Clean
Final Drive Oil Level - Check
Swing Bearing - Lubricate
Swing Drive Oil Level - Check

Every 250 Service Hours of Partial Hammer Use (50% of Service Hours)
Hydraulic System Oil Filter (Case Drain) - Replace
Hydraulic System Oil Filter (Pilot) - Replace

Every 250 Service Hours of Continuous Hammer Use

Hydraulic System Oil Filter (Case Drain) - Replace
Hydraulic System Oil Filter (Pilot) - Replace
Hydraulic System Oil Filter (Return) - Replace

Initial 500 Hours (for New Systems, Refilled Systems, and Converted Systems)
Cooling System Coolant Sample (Level 2) - Obtain

Every 500 Service Hours

Hydraulic System Oil Sample - Obtain
Swing Drive Oil Sample - Obtain

Every 500 Service Hours or 3 Months

Boom and Stick Linkage - Lubricate
Engine Crankcase Breather - Clean
Engine Oil and Filter - Change
Fuel System Primary Filter (Water Separator) Element - Replace
Fuel System Secondary Filter - Replace
Fuel Tank Cap and Strainer - Clean

Every 500 Service Hours of Partial Hammer Use (50% of Service Hours)
Hydraulic System Oil Filter (Case Drain) - Replace
Hydraulic System Oil Filter (Pilot) - Replace
Hydraulic System Oil Filter (Return) - Replace

https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 09/06/2014
336D L Excavators M4T00001-UP (MACHINE) POWERED BY C9 Engine(SEBP... Página 4 de 5

Every 600 Service Hours of Continuous Hammer Use

Hydraulic System Oil - Change

Every 1000 Service Hours or 6 Months

Battery - Clean
Battery Hold-Down - Tighten
Engine Valve Lash - Check
Final Drive Oil Level - Check
Hydraulic System Oil Filter (Case Drain) - Replace
Hydraulic System Oil Filter (Pilot) - Replace
Swing Drive Oil - Change

Every 1000 Service Hours of Partial Hammer Use (50% of Service Hours)
Hydraulic System Oil - Change
Hydraulic System Oil Filter (Return) - Replace

Every 2000 Service Hours or 1 Year

Final Drive Oil - Change
Hydraulic System Oil - Change
Hydraulic System Oil Filter (Return) - Replace
Hydraulic Tank Screen - Clean
Receiver Dryer (Refrigerant) - Replace
Swing Gear - Lubricate

Every Year
Cooling System Coolant Sample (Level 2) - Obtain

Every 3 Years After Date of Installation or Every 5 Years After Date of

Manufacture
Seat Belt - Replace

Every 4000 Service Hours or 2 Years

Hydraulic System Oil - Change

Every 6000 Service Hours or 3 Years

Cooling System Coolant Extender (ELC) - Add

Every 12 000 Service Hours or 6 Years

Cooling System Coolant (ELC) - Change

https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 09/06/2014
336D L Excavators M4T00001-UP (MACHINE) POWERED BY C9 Engine(SEBP... Página 5 de 5

Copyright 1993 - 2014 Caterpillar Inc. Mon Jun 9 16:10:12 UTC-0300 2014
All Rights Reserved. u060jcc
Private Network For SIS Licensees.

https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 09/06/2014