Overview / Tubtara® Blind Rivet Nuts

Tubtara® fasteners with seal

Trusted, low-maintenance, watertight

Watertight HX closed-end Tubtara® fasteners with Watertight (H)DPX Tubtara® with applied sealant
O-ring seal (mechanical) under head (chemical)

— Large flanged head with a cylindrical groove and O-ring — Non-reactive peripheral seal made of flexible organic-
seal mounted underneath based material, applied under the head
— The seal slides into the groove and – regardless of the — The seal material is gap filling, forming a robust seal
setting force – is compressed between the head and the between the mating surfaces
plate during installation. — Slight variations in seal thickness may influence head
— M
etal-to-metal contact after setting for spin-out resistance. height and grip range
— The closed-end hexagonal shank (HX) guards against — The seal is resistant to many automotive oils, antifreeze
potential burr and sharp hole edges. and transmission fluids
— The seal is fully protected against UV light influence. — Can be applied on stocked standard Tubtara® parts (all
— E
xcellent protection against the ingress of fluids, moisture, materials and shank types)
oil, or dirt, even when subjected to high pressure of at — IP 67 guaranteed under in-house testing conditions.
least 10 bar.
— Various seal materials available, such as Viton, EPDM
or silicone.
— I P 68 guaranteed under in-house testing conditions.

Seal Seal Seal Head IP Temperature Sealing capacity UV-shielded Shore Standard - ST /
type material colour type rating range hardness on request
HX NBR black large HX IP 681 -30°C +120°C tested to 10 bar: IP 681 YES approx. 70 ST
HX EPDM black large HX IP 681 -50°C +120°C tested to 10 bar: IP 681 YES approx. 70 on req.
HX Viton black large HX IP 681 -20° +200°C tested to 10 bar: IP 681
YES approx. 70 on req.
D1 polyurethane blue P, F3 IP 671 -40°C +100°C > 150 bar NO approx. 50 A ST
resin (max. +150°C)
D2 polyurethane green P, F3 IP 671 -40°C +100°C > 150 bar NO 50 – 65 A on req.
acrylate
D3 silicone red P, F3 IP 672 -50°C +300°C > 150 bar NO 43 A on req.
D4 acrylate light blue K3 IP 34 - IP 672 -60°C +160°C low (weak seal) NO on req.
D5 epoxy-based yellow P, F 3
IP 67 2
-40°C +150°C > 150 bar NO 50 D on req.
Subject to change

1
Under Dejond testing conditions

2
Depending on hole and handling quality, subject to testing

3
P: flat head - F: countersunk head, subject to testing - K: low profile head

Titgemeyer/10038EN0120/1 61
Tubtara® Blind Rivet Nuts / Flat Head

Tubtara® blind rivet nuts

Flat head Before After

setting setting

Full-hexagonal shank with seal, closed end

IP rating: IP68 Seal

Material Hex shank

Steel, Zinktop 480h

Thread Grip range Hex hole ø Hexagonal shank Head ø Head height Shank length Description Article No.
d1 s +0.1 SW -0.02 -0.15 D ±0.35 k ±0.15 L ±0.35
6H [mm] [mm] [mm] [mm] [mm] [mm]
M5 0.5 - 3.0 7.0 7.0 12.5 1.5 19.0 HX 3001 339 245 9502
M6 0.5 - 3.0 9.0 9.0 15.0 1.5 21.5 HX 3001 339 695 950
3.0 - 5.5 9.0 9.0 15.0 1.5 23.5 HX 5501 339 696 9502
M8 0.5 - 3.0 11.0 11.0 20.0 2.0 26.7 HX 3001 339 850 950
3.0 - 6.0 11.0 11.0 20.0 2.0 29.7 HX 6001 339 851 9502
6.0 - 8.0 11.0 11.0 20.0 2.0 31.7 HX 8001 339 852 950
2
Not a stock item - contact us for minimum quantities

Subject to change

62 Titgemeyer/10038EN0120/1
 Tubtara® Blind Rivet Nuts / Flat Head

Tubtara® blind rivet nuts

Flat head Before After

setting setting

Full-hexagonal shank with seal, closed end

IP rating: IP68 Seal

Material Hex shank

Stainless steel AISI 304 Cu 1.4567

Thread Grip range Hex hole ø Hexagonal shank Head ø Head height Shank length Description Article No.
d1 s +0.1 SW -0.02 -0.15 D ±0.35 k ±0.15 L ±0.35
6H [mm] [mm] [mm] [mm] [mm] [mm]
M5 0.5-3.0 7.0 7.0 13.5 1.5 19.0 HX 3001 334 080 000
M6 0.5-3.0 9.0 9.0 16.0 1.5 21.5 HX 3001 334 082 000
M8 0.5-3.0 11.0 11.0 21.0 2.0 25.0 HX 3001 334 084 000
Subject to change

Titgemeyer/10038EN0120/1 63
Tubtara® Blind Rivet Nuts / Flat Head

Tubtara® blind rivet nuts

Flat head Before After

setting setting

Semi-hexagonal shank with seal, closed end

IP rating: IP68 Seal

Material Hex shank

Stainless steel AISI 316 Cu 1.4578

Exceptionally high corrosion resistance

Thread Grip range Hex hole ø Hexagonal shank Head ø Head height Shank length Description Article No.
d1 s +0.1 SW -0.02 -0.15 D ±0.35 k ±0.15 L ±0.35
6H [mm] [mm] [mm] [mm] [mm] [mm]
M5 0.5 - 3.0 7.0 7.0 13.5 1.5 19.0 HX 3001 334 090 0002
M6 0.5 - 3.0 9.0 9.0 16.0 1.5 21.5 HX 3001 334 092 0002
2.0 - 4.5 9.0 9.0 16.0 1.5 21.5 HX 4501 334 093 000
M8 0.5 - 3.0 11.0 11.0 21.0 2.0 25.0 HX 3001 334 094 0002
2
Not a stock item - contact us for minimum quantities

Subject to change

64 Titgemeyer/10038EN0120/1
 Tubtara® Blind Rivet Nuts / Flat Head with Seal

Tubtara® blind rivet nuts

Flat head with seal

D

k2
k
Round shank, closed end

s
IP rating: IP67
seal

L
Material

Stainless steel AISI 304 Cu 1.4567 d1

d

Thread Grip range Hole ø Shank ø Head ø Head height Head height Shank length Description Article No.
d1 s +0.1 d -0.02 -0.15 D ±0.35 k ±0.15 k2 L ±0.35
6H [mm] [mm] [mm] [mm] [mm] [mm] [mm]
M4 0.5 – 1.5 6.0 6.0 9.0 1.0 1.3 15.0 DPX15 334 055 000
M5 0.5 – 2.5 7.0 7.0 10.0 1.0 1.3 17.5 DPX25 334 056 000
2.5 - 4.5 7.0 7.0 10.0 1.0 1.3 19.5 DPX45 334 057 000
M6 0.5 – 2.5 9.0 9.0 12.0 1.5 1.9 21.5 DPX25 334 058 000
2.5 – 4.5 9.0 9.0 12.0 1.5 1.9 23.5 DPX45 334 059 000
M8 0.5 – 2.5 11.0 11.0 15.0 1.5 2.0 23.5 DPX25 334 060 000
2.5 – 5.0 11.0 11.0 15.0 1.5 2.0 26.0 DPX50 334 061 000

Note 1:
IP 67 possible under ideal conditions

Note 2:
K2 is for reference purposes only – the type of seal,
size of hole, setting force and other factors
significantly impact dimension K2
Subject to change

Titgemeyer/10038EN0120/1 65
Tubtara® Blind Rivet Nuts / Flat Head with Seal

Tubtara® blind rivet nuts

Flat head with seal

D

k2
k
Semi-hexagonal shank, closed end

s
IP rating: IP67 seal

L
Material

Stainless steel AISI 304 Cu 1.4567 d1

SW

Thread Grip range Hex hole ø Hexagonal shank Head ø Head height Head height Shank length Description Article No.
d1 s +0.1 SW -0.02 -0.15 D ±0.35 k ±0.15 k2 L ±0.35
6H [mm] [mm] [mm] [mm] [mm] [mm] [mm]
M4 0.5 – 1.5 6.0 6.0 9.0 1.0 1.3 15.0 HDPX15 334 062 000
M5 0.5 – 2.0 7.0 7.0 10.0 1.0 1.3 17.5 HDPX20 334 063 000
M6 0.5 – 2.0 9.0 9.0 12.0 1.5 1.9 21.5 HDPX20 334 064 000
2.0 - 4.0 9.0 9.0 12.0 1.5 1.9 23.5 HDPX40 334 065 000
M8 0.5 – 2.0 11.0 11.0 15.0 1.5 2.0 23.5 HDPX20 334 066 000
2.0 - 4.5 11.0 11.0 15.0 1.5 2.0 26.0 HDPX45 334 067 000

Note 1:
IP 67 possible under ideal conditions

Note 2:
K2 is for reference purposes only – the type of seal,
size of hole, setting force and other factors
significantly impact dimension K2

Subject to change

66 Titgemeyer/10038EN0120/1
 Tubtara® Blind Rivet Nuts / Flat Head with Seal

Tubtara® blind rivet nuts

Flat head with seal

D

k2
k
Round shank, closed end

s
IP rating: IP67
seal

L
Material

Stainless steel AISI 316 Cu 1.4578 d1

d

Exceptionally high corrosion resistance

Thread Grip range Hole ø Shank ø Head ø Head height Head height Shank length Description Article No.
d1 s +0.1 d -0.02 -0.15 D ±0.35 k ±0.15 k2 L ±0.35
6H [mm] [mm] [mm] [mm] [mm] [mm] [mm]
M4 0.5 – 1.5 6.0 6.0 9.0 1.0 1.3 15.0 DPX15 334 048 000
M5 0.5 – 2.5 7.0 7.0 10.0 1.0 1.3 17.5 DPX25 334 049 000
2.5 - 4.5 7.0 7.0 10.0 1.0 1.3 19.5 DPX45 334 050 000
M6 0.5 – 2.5 9.0 9.0 12.0 1.5 1.9 21.5 DPX25 334 051 000
M8 0.5 – 2.5 11.0 11.0 15.0 1.5 2.0 23.5 DPX25 334 052 000

Note 1:
IP 67 possible under ideal conditions

Note 2:
K2 is for reference purposes only – the type of seal,
size of hole, setting force and other factors
significantly impact dimension K2
Subject to change

Titgemeyer/10038EN0120/1 67
Tubtara® Blind Rivet Nuts / Flat Head with Seal

Tubtara® blind rivet nuts

Flat head with seal

Semi-hexagonal shank, closed end

IP rating: IP67

Material

Stainless steel AISI 316 Cu 1.4578

Exceptionally high corrosion resistance

Thread Grip range Hex hole ø Hexagonal shank Head ø Head height Head height Shank length Description Article No.
d1 s +0.1 SW -0.02 -0.15 D ±0.35 k ±0.15 k2 L ±0.35
6H [mm] [mm] [mm] [mm] [mm] [mm] [mm]
M4 0.5 – 1.5 6.0 6.0 9.0 1.0 1.3 15.0 HDPX15 334 042 000
M5 0.5 – 2.0 7.0 7.0 10.0 1.0 1.3 17.5 HDPX20 334 043 000
M6 0.5 – 2.0 9.0 9.0 12.0 1.5 1.9 21.5 HDPX20 334 044 000
2.0 - 4.0 9.0 9.0 12.0 1.5 1.9 23.5 HDPX40 334 045 000
M8 0.5 – 2.0 11.0 11.0 15.0 1.5 2.0 23.5 HDPX20 334 046 000
2.0 - 4.5 11.0 11.0 15.0 1.5 2.0 26.0 HDPX45 334 047 000

Note 1:
IP 67 possible under ideal conditions

Note 2:
K2 is for reference purposes only – the type of seal,
size of hole, setting force and other factors
significantly impact dimension K2

Subject to change

68 Titgemeyer/10038EN0120/1