7/15/23, 1:31 PM Standard Penetration Test (SPT)-Procedure,Precautions, Advantages - The Constructor

🔍 Search 📰 Ask A

Standard Penetration Test (SPT)-Procedure,Precautions,

Advantages
⌂ Home / Geotechnical Engineering

🕑 Reading time: 1 minute

Standard Penetration Test (SPT)

The standard penetration test is an in-situ test that is coming under the category of penetrometer tests. The standard penetration tests are carried out i
borehole. The test will measure the resistance of the soil strata to the penetration undergone. A penetration emphirical correlation is derived between t
soil properties and the penetration resistance. The test is extremely useful for determining the relative density and the angle of shearing resistance of
cohesionless soils. It can also be used to determine the unconfined compressive strength of cohesive soils.

Tools for Standard Penetration Test

The requirements to conduct SPT are:

1. Standard Split Spoon Sampler

2. Drop Hammer weighing 63.5kg
3. Guiding rod
4. Drilling Rig.
5. Driving head (anvil).

Procedure for Standard Penetration Test

The test is conducted in a bore hole by means of a standard split spoon sampler.Once the drilling is done to the desired depth, the drilling tool is remov
and the sampler is placed inside the bore hole. By means of a drop hammer of 63.5kg mass falling through a height of 750mm at the rate of 30 blows pe
minute, the sampler is driven into the soil. This is as per IS -2131:1963. The number of blows of hammer required to drive a depth  of 150mm is counted
Further it is driven by 150 mm and the blows are counted. Similarly, the sampler is once again further driven by 150mm and the number of blows
recorded. The number of blows recorded for the first 150mm not taken into consideration.. The number of blows recorded for last two 150mm intervals
are added to give the standard penetration number (N). In other words,
N = No: of blows required for 150mm penetration beyond seating drive of 150mm.

https://theconstructor.org/geotechnical/standard-penetration-test-procedure-precautions-advantages/4657/ 1/5
7/15/23, 1:31 PM Standard Penetration Test (SPT)-Procedure,Precautions, Advantages - The Constructor

Fig.1: Standard penetration Test

If the number of blows for 150mm drive exceeds 50, it is taken as refusal and the test is discontinued. The standard penetration number is corrected fo
dilatancy correction and overburden correction.

Corrections in Standard Penetration Test

Before the SPT values are used in empirical correlations and in design charts, the field ‘N’ value have to be corrected as per IS 2131 – 1981. The correctio
are:

1. Dilatancy Correction
2. Overburden Pressure Correction
1. Dilatancy Correction
Silty fine sands and fine sands below the water table develop pore water pressure which is not easily dissipated. The pore pressure increases the
resistance of the soil and hence the penetration number (N). Terzaghi and Peck (1967) recommend the following correction in the case of silty fine sand
when the observed value is N exceeds 15. The corrected penetration number,
NC = 15 + 0.5 (NR -15)

Where NR is the recorded value and NC is the corrected value. If NR  less than or equal to 15, then Nc = NR 2. Overburden Pressure Correction From
several investigations, it is proven that the penetration resistance or the value of N is dependent on the overburden pressure. If there are two granular
soils with relative density same, higher ‘N’ value will be shown by the soil with higher confining pressure. With the increase in the depth of the soil, the
confining pressure also increases. So the value of ‘N’ at shallow depth and larger depths are underestimated and overestimated respectively. Hence, to
account this the value of ‘N’ obtained from the test are corrected to a standard effective overburden pressure. The corrected value of ‘N’ is
Nc = CN N

Here CN is the correction factor for the overburden pressure.

 Precautions taken for Standard Penetration Test

1. Split spoon sampler must be in good condition.
2. The cutting shoe must be free from wear and tear
3. The height of fall must be 750mm. Any change from this will affect the ‘N’ value.
4. The drill rods used must be in standard condition. Bent drill rods are not used.
5. Before conducting the test, the bottom of the borehole must be cleaned.

Advantages of Standard Penetration Test

https://theconstructor.org/geotechnical/standard-penetration-test-procedure-precautions-advantages/4657/ 2/5
7/15/23, 1:31 PM Standard Penetration Test (SPT)-Procedure,Precautions, Advantages - The Constructor

The advantages of standard penetration test are:

1. The test is simple and economical

2. The test provides representative samples for visual inspection, classification tests and for moisture content.
3. Actual soil behaviour is obtained through SPT values
4. The method helps to penetrate dense layers and fills
5. Test can be applied for variety of soil conditions

Disadvantages of Standard Penetration Test

The limitations of standard penetration tests are:

1. The results will vary due to any mechanical or operator variability or drilling disturbances.
2. Test is costly and time consuming.
3. The samples retrieved for testing is disturbed.
4. The test results from SPT cannot be reproduced
5. The application of SPT in gravels, cobbles and cohesive soils are limited

 ShareThisFacebook
Article   

← Previous article
Quality Test in Rainwater Harvesting- H2S Strip Test

Next article
What are Different Chemical Tests on Concrete Structu

Gopal Mishra

Gopal Mishra ✓

Related Posts

The Science Behind Stabilizing Tunnel Portals What Types Of Roofing Sheets Are Best For Home Constructio

https://theconstructor.org/geotechnical/standard-penetration-test-procedure-precautions-advantages/4657/ 3/5
7/15/23, 1:31 PM Standard Penetration Test (SPT)-Procedure,Precautions, Advantages - The Constructor

📖 Popular Articles

Types of Foundation for Buildings and their Uses [PDF]

G
Compressive Strength of Concrete -Cube Test [PDF], Procedure, Results
G
16 Types of Heavy Equipment Used in Construction
S
Calculate Quantities of Materials for Concrete -Cement, Sand, Aggregates
G
Methods of Rainwater Harvesting [PDF]: Components, Transportation, and Storage

📖 Recent Articles

Advantages And Disadvantages Of Cement Concrete Roads: What You Need To Know

Factors That Influence Highway Alignment And Their Impact

WBM Road Construction Advantages And Disadvantages

Road Camber: Understanding Its Importance And Benefits

Construction Equipment: Rent, Buy, Or Lease?

📖 Recent Questions

Which is the code used for the design of the RCC Bridge?
 1 Answer

What is the tolerance for compression test results of concrete, according to the standards?
 1 Answer

What must be the maximum dry density of Granular Sub Base & Wet Mix Macadam used ...
G  1 Answer

What is the Safe Bearing Capacity values for Different Soils?

G  1 Answer

What are the different types of handrails used in bridges?

G  1 Answer

⌂ Home
 About Us
 Contact Us

https://theconstructor.org/geotechnical/standard-penetration-test-procedure-precautions-advantages/4657/ 4/5
7/15/23, 1:31 PM Standard Penetration Test (SPT)-Procedure,Precautions, Advantages - The Constructor

 Privacy Policy
 Terms & Conditions
 Ask Questions
✎ Write for us
 Popular Questions
 Facebook
 Instagram
 Twitter
 Telegram

Search ...

Articles

Search

© 2009-2021 The Constructor. All Rights Reserved.

https://theconstructor.org/geotechnical/standard-penetration-test-procedure-precautions-advantages/4657/ 5/5