Scribd
Upload
18 views

Mid Term Exam 2009 2010

This document is the midterm exam for an industrial engineering course. It contains 3 questions testing stress analysis concepts. Question 1 has 5 parts testing forces, stresses, and deflections in a link under loading. Question 2 has 2 parts: part A tests allowable load and stress concentration, and part B tests stresses and deflections in two materials under force. Question 3 has 2 parts: part A tests shaft design for power transmission, and part B tests torque and twist angle transmission through gears. The exam tests a variety of engineering calculations and concludes by wishing the student the best.

Uploaded by

محمد معوض
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
18 views

Mid Term Exam 2009 2010

This document is the midterm exam for an industrial engineering course. It contains 3 questions testing stress analysis concepts. Question 1 has 5 parts testing forces, stresses, and deflections in a link under loading. Question 2 has 2 parts: part A tests allowable load and stress concentration, and part B tests stresses and deflections in two materials under force. Question 3 has 2 parts: part A tests shaft design for power transmission, and part B tests torque and twist angle transmission through gears. The exam tests a variety of engineering calculations and concludes by wishing the student the best.

Uploaded by

محمد معوض
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Faculty of Engineering Fayoum University

Industrial Department
2nd year, 1st term
Stress Analysis
Time (2 hours)
Mid Term Exam (2009/2010)

Question No. (1); (15 points)


In the hanger shown, the upper portion of link ABC is 10 mm thick and the lower
portions are each 6 mm thick. Epoxy resin is used to bond the upper and the lower
portions together at B. The pin at A is of 10 mm diameter while a 6 mm diameter
pin is used at C. Determine:
a. The force in link ABC.
b. The largest normal stress in link ABC.
c. The shearing stress in pin C.
d. The average shearing stress on the
bonded surface at B.
e. The bearing stress in the link at c.

*****************************************************************
Question No. (2); (20 points; (5+15))
(A) Knowing that the allowable stress is 140 MPa and the stress concentration
factor K is 2.1. Determine:
a. The maximum allowable magnitude
of the centric load P.
b. The percent change in the maximum
allowable magnitude of P if the raised
portions are removed at the end of the specimens.
**************************************************
(B) Link BD is made of brass (E = 105 GPa) and has a cross sectional area of 250
mm2. Link CE is made of aluminum (E = 72 GPa) and has a cross sectional
area of 450 mm2. If force P equal to 50 KN
is applied at point A, determine:
a. The normal stress in link BD and link CE.
b. The deflection at point B and point C.
c. The deflection at point A.
Question No. (3); (15 points; (5+10))
(A) Design a solid steel shaft to transmit 0.375 KW at a frequency of 29 Hz, if the
shearing stress in the shaft is not to exceed 35 MPa.
**************************************************
(B) Two solid steel shafts (G = 77 GPa) are connected by the gears shown.
Knowing that the radius of gear B is r B = 20 mm, when torque T A = 75 N.m is
applied at the free end A. Determine:
a. The torque which may be applied at shaft CD.
b. The angle of twist at point A.

********************************************************************************
THE END
WITH MY BEST WISHES

You might also like