TECHNICAL SPECIFICATION

Group-B

Group B-Pipe Fitting

Pipe Plug
1 154000118 1/4 " NPTM 60
2 80019002 1/2 " NPTM 70
3 153116077 1/8 " NPTM 70
4 150010600 1 " NPTM 30
5 154000119 3/8 " NPTM 30
6 80019003 3/4'' NPTM 20
Pipe Cap
7 153101165 3/8 " NPTF 20
8 153101166 1/2 " NPTF 20
9 153101162 1/4" NPTF 15
Pipe Nipple
10 153102824 1/2"NPTMX1/2"NPTM NIPPLE 4" SS316 60
11 80025012 1/4" NIPPLE (SHORT) 50
12 80025013 NIPPLE 1/2" NPTM 60
13 80025014 3/8" NIPPLE 25
14 153101169 HEX NIPPLE 1/4" NPTM, 3" LENGTH 50
15 80025016 1/4"NPTM,Nipple 1'' long 10
16 80025014 3/8"NPTM Nipple 1/2'' long 10
17 150010620 3/8" NPTM Nipple 4" long 10
18 153103332 1/2" NPTM Nipple 1/2'' long 10
19 153103332 1/2" NPTM Nipple 1'' long 10
20 150010621 1/2" NPTM Nipple 2'' long 10
21 150010622 1/2" NPTM Nipple 3'' long 20
22 154000104 1" NPTM Nipple 1'' long 20
Reducer Nipple
23 153107992 3/4" NPTM X 1/2" NPTM 10
24 150010623 1/4" NPTM X 1/8" NPTM 10
25 150010624 1/4" NPTM X 3/8" NPTM 10
26 153102823 1/4" NPTM X 1/2" NPTM 10
27 150008116 1/2" NPTM X 3/8" NPTM 20
Pipe Elbow
28 80300901 1/4"NPTF SS316 PIPE ELBOW 20
29 153101159 1/2"NPTF SS316 PIPE ELBOW 20
Pipe Adapter
30 80043010 PIPE ADAPTOR 1/4" NPTF* 1/2" NPTM 35
 31 80043011 PIPE ADAPTOR 1/2" NPTF* 1/4" NPTM 35
32 150010625 PIPE ADAPTER 1/2 " NPTF X 3/4 " NPTM 35
33 150010626 PIPE ADAPTER 1/2 " NPTM X 3/4 " NPTF 25
34 150010627 PIPE ADAPTER 3/4"NPTM X 1/2"NPTM 30
35 150010628 PIPE ADAPTER 1/2"NPTF X 3/4"NPTF 20
36 150010629 1/2" NPTM X 3/8" NPTF 10
37 150010630 3/4" NPTM X 1/2" NPTF 10
38 150010631 3/4" NPTM X 3/8" NPTF 10
39 153101148 1" NPTM X 1/2" NPTF 10
40 150010632 1" NPTM X 1/4" NPTF 10
41 150010633 1" NPTM X 1" NPTF 10
42 150010634 3/4" NPTF X 3/4" NPTF 10
43 150010635 1" NPTM X 3/4" NPTF 10
Cross
44 150010530 CROSS 3/4'' NPTF 10
45 150010531 CROSS 1'' NPTF 10
Pipe Tee
46 153101160 1/2 " NPTF 20
47 150010532 1''NPTF X 1''NPTF X 1''NPTF 10
48 150010533 1" NPTM X 1" NPTM X 1" NPTM 10
49 150010534 3/4" NPTF X 3/4" NPTF X 3/4" NPTF 10

2. GENERAL SPECIFICATIONS FOR PIPE FITTINGS.

The SS 316 Pipe Fittings and the Valves shall be designed for withstanding High Pressure & Temperature and
Vibration Impulses for use in various services like Air, Natural Gas, Crude Oil and Petroleum by products. The
Fittings and the Valves must be capable of transporting pressurized Liquid/ Gas at low and high Temperature
without any leakage or failure and shall be able to withstand axial and lateral forces within the Industrial
Piping Installations. All the parts of the Fittings shall be concentric as per the Piping size and capable of self-
alignment when assembled. The Fittings and the Valves shall not significantly reduce the flow area and shall
not weaken the Tube Wall.
Better materials are acceptable subjected to approval of ONGC. Change in material should be conveyed to
ONGC with supporting documents.
Samples for testing shall be picked up from final finished complete lot and the sample size shall be as per the
testing procedure.
2.1 Pipe Fittings

I. The entire bend Pipe Fittings shall be of Hexagonally Forged SS316 in conformation to ASME-SA-182 / ASTM A-
182.
II. All the straight Pipe Fittings shall be of SS316 Bar Stock in conformation to ASME –SA-479 / ASTM A276.
III. Pipe threads shall be NPT as per ASME B1.20.1 / ANSI B1.20.1.
IV. NPT threads shall be of uniform thread profile.
V. All the exposed thread shall be protected from damage.
VI. Working pressure should be calculated as per pressure Piping Code ASME B.31.3./ ANSI B.31.1 power piping

2.2 Testing:
Following Tests shall be witnessed by ONGC quality assurance department or by an approved TPI at ONGC
cost with a sample size of 10 no’s picked at random from different sizes from the ordered quantity and report
shall be submitted along with the supply.
a) Visual Examination: Fittings shall be checked for overall finish, workmanship and dimension. Threads shall be
checked with Ring/Plug step gauge (with Min. / Max. limits).
b) Pneumatic pressure test: Pneumatic pressure test is to be conducted at 3,600 psi for 05 minutes. No bubbling
is allowed.
c) Hydrostatic pressure test: After the completion of Pneumatic Pressure Test, the Loop shall be pressurized to
5,000 PSI by Hydraulic / Hydrostatic Media and shall be kept for 05 minutes. No leakage shall be allowed (similar
to Bubble Tight Shut Off).
d) All the above Tests shall be carried out at the Manufacturer’s premises for which all the relevant facilities shall
be available with the Manufacturer except for Material Test for which sample shall be given to the Govt.
approved Test Laboratory, cost for the testing of the same shall be borne by the bidder. Bidder should provide
copies of all codes referred above at the time of inspection and testing for reference.
Inspection shall be done by ONGC QAD or by any ONGC approved TPI

Make for Group B: Swagelok, USA/ Circor (HOKE) Instrumentation Ltd, USA/ Parker,
USA/Astec Valves & Fittings Private Limited, India/
DK Tech, South Korea/Ham-Let Advanced Control Technology, Israel/
Precision Engineering Industries, Mumbai/ Fluid Controls Pvt. Ltd., India/
HyLok Corporation, Korea/Panam Engineers Ltd., Mumbai/
Allied Engineering Pvt.Ltd,India/Havi Engineering India Private
Limited,India/ MET-LOK Valves and
Fittings, India/ AB Sandvik Material Technology, Sweden / Tubacex Tubos
Inoxidables, S.A., Spain/Fine Tubes, UK/ Ratnamani Metals & Tubes Ltd,
India/Dong Nam Korea Co. Ltd., South Korea/Equivalent*
Note:

*For equivalent make: For offering equivalent make, they have to provide PTR (Proven Track Record)
mentioned as Experience Clause in GeM ATC