Safe Work Method Statement

Project Name: OLA Cell technologies private limited DATE:18.07.2023  

Company Name

Address:

Office Contact No:

Project Manager Name Contact No:

ACIVITY : REINFORCEMENT WORKS

The person who

Procedure (in steps) Possible Hazards Risk Control Measures will ensure this
Rating (Describe what action or procedure will be happens
(Break the job down into steps. Each step (Identify the hazards associated with (See taken to eliminate or minimize the risk of injury
should accomplish some major task and each step. Examine each to find below) or damage. Use the Hierarchy of Controls
be in logical sequence.) possibilities that could lead to an accident below as a guide
or potential harm arising.) 1. Eliminate the Hazard
2. Substitute the material or equipment
3. Isolate the hazard
4. Implement Engineering control
5. Implement Administrative control
6. PPE
1. Manual bar bending.  Defective tools.  Do not use sub-standard tools.
 Wrong application of tools.  Ensure usage of right tools for right
 Wrong posture. job.
 Do not push tools while bending.
 Hold firmly.
 Adhere to correct and safe posture.
 Provide protection cover on all
moving parts of machine / tool.

Document Name: Version Correct as at:

SWMS for brickwork and plastering 01 11.01.2023
 Safe Work Method Statement
The person who
Procedure (in steps) Possible Hazards Risk Control Measures will ensure this
Rating (Describe what action or procedure will be happens
(Break the job down into steps. Each step (Identify the hazards associated with (See taken to eliminate or minimize the risk of injury
should accomplish some major task and each step. Examine each to find below) or damage. Use the Hierarchy of Controls
be in logical sequence.) possibilities that could lead to an accident below as a guide
or potential harm arising.) 1. Eliminate the Hazard
2. Substitute the material or equipment
3. Isolate the hazard
4. Implement Engineering control
5. Implement Administrative control
6. PPE
2. Rebaring ( Use of high RPM  Human injury  Get the electrically operated tools
cutting tools, Long rebar and tackles inspected by the
handling) electrical department for fitness and
correctness.
 Bar bending to be done on proper
table with proper holding
arrangements.

 Deploy minimum three persons for

handling full length rebar.

 Keep surrounding swing area free

for safe handling while cutting.

 Move bars horizontally.

 Protruding rears bent down.

 Reflecting cap provided to exposed

bar.

Document Name: Version Correct as at:

SWMS for brickwork and plastering 01 11.01.2023
 Safe Work Method Statement
The person who
Procedure (in steps) Possible Hazards Risk Control Measures will ensure this
Rating (Describe what action or procedure will be happens
(Break the job down into steps. Each step (Identify the hazards associated with (See taken to eliminate or minimize the risk of injury
should accomplish some major task and each step. Examine each to find below) or damage. Use the Hierarchy of Controls
be in logical sequence.) possibilities that could lead to an accident below as a guide
or potential harm arising.) 1. Eliminate the Hazard
2. Substitute the material or equipment
3. Isolate the hazard
4. Implement Engineering control
5. Implement Administrative control
6. PPE
3. Reinforcement Shifting to work  Human injury.  Clear front while handling it to site.
Location. (Manually ,By Hydra  Material may fall on person.  Use of leverage bars does not apply
& Tower Crane.)  Using of damaged lifting tools and hand directly in bundles.
tackles.  Make use of hydra or suitable lifting
machine to load on trailer.
 Make sure the trailer wheels are
locked with stopper and breaks
applied.
 Ensure to use good condition tools
only.
 Ensure to worn the full body
harness.

 Ensure to provide the plat form on

scaffold.
4. Cutting wire by tools  Defective tools.  Use proper binding before going to
 Personal injury. cutting.
 Damage of tools.  Take exta care while walking
around the work site.
 Remove all Combustible material
near to cutting area

Document Name: Version Correct as at:

SWMS for brickwork and plastering 01 11.01.2023
 Safe Work Method Statement
The person who
Procedure (in steps) Possible Hazards Risk Control Measures will ensure this
Rating (Describe what action or procedure will be happens
(Break the job down into steps. Each step (Identify the hazards associated with (See taken to eliminate or minimize the risk of injury
should accomplish some major task and each step. Examine each to find below) or damage. Use the Hierarchy of Controls
be in logical sequence.) possibilities that could lead to an accident below as a guide
or potential harm arising.) 1. Eliminate the Hazard
2. Substitute the material or equipment
3. Isolate the hazard
4. Implement Engineering control
5. Implement Administrative control
6. PPE
5. Reinforcement  Curtailment and binding of rods.  Use PPE like gloves, shoes,
 Carrying of rods for short helmets,etc.
distances/ at height.  Avoid usage of make-shift tools.
 Checking of clear distance/ cover  Provide suitable pads on shoulders
with hands. and use safety gloves.
 Hitting projected rods and standing  Ensure proper staging.
on cantilever rods.  Use measuring devices like
 Persons may get injured . tape ,measuring rods, etc.
 Workers may get injured on their  Avoid wearing of loose cloths.
hands and shoulders.
 Rods may cut or injure the fingers.
 Persons may get injured and fall
down
 Protruded rods may hit the persons

Document Name: Version Correct as at:

SWMS for brickwork and plastering 01 11.01.2023
 Safe Work Method Statement

Personnel Summary
SUPERVISOR’S DETAILS
Supervisors Name & Qualifications: Name:
Experience:
Qualifications:

Prepared by: Signature: Date:

(Principle Contractor HSE Manager)

Reviewed by : Signature: Date:

(Principle Contractor Project Manager)

Reviewed by Signature Date:

(JLLSafety Manager)

Approved by
(JLL Project Manager) Signature Date:

Document Name: Version Correct as at:

SWMS for Brick work and plastering 01 11.01.2023