Calculation 

Noted 
 
Structural Design  
 
 
 
According to ACI318M‐11 
I. Design Report: Reference
 Design Code : ACI 318-11
 Design Load : ASCE/SEI 7-10
fsfs

I. Materials:
 Modulus of Elasticity of Concrete : Ec  0.043   1.5  f c ' MPa (ACI318-11 Section 8.5.1)

 Modulus of Elasticity of Steel : Es  200, 000MPa (ACI318-11 section 8.5.2)

 Concrete Strength (Cylinder) : fC '  28MPa for Footing and Column

 Concrete Strength (Cylinder) : f C '  28MPa for Beam and Slab

 Steel Strength (Main bar) : Fy  390MPa

 Steel Strength (Confinement bar) : Fys  390 MPa

kN
 Unit Weight of Concrete :  c  24
m3
kN
 Unit Weight of Steel :  s  77 3
m

II. Design Loads:

 Dead Load
 Surcharge

 Ceramic tile and Mortar : DL  1.10 kN / m2

 Mechanical duct allowance : DL  0.1kN / m2

 Suspended Metal lath and gypsum plaster : DL  0.3 kN / m2

 Partition : DL  1.0 kN / m2

 Wall

 Brick Wall 200mm : DL  3.0 kN / m2 x h

 Surcharge Load on roof

 Roof Tile and Purlin : DL  0.45 kN / m2

  Live Load

 Function

 Floor : LL  4.79 kN / m 2 (ASCE7-10 Table 4-1)

 Roof Live Load : LLr  0.30 kN / m 2

 Wind Load

 Basic Wind : V  75 mph (120 Km )

h

 Exposure category “ B “ (ASCE7-10 section 26.7.3)

 Wind Pressure

 Windward wall : C p  0.8 (ASCE7-10 Table 27.4.1)

 Leeward wall : C p   0.5 (ASCE7-10 Table 27.4.1)

 Load Combination (ASCE7-10 section 2.3)

II. Systems:
 Structural Form : Wall-Frame Structures

 Floor Systems-Reinforced Concrete : Two Way Slab and Beam

III. Modeling for Analysis:
I. Preliminary Dimension :
i. For Beam
 Beam Height (h)
L
 for Simply Support  Note: for fy other than 420MPa, The value
16 shall be multiplied by (0.4 + fy/700)
L
 for One end continuous
18.5

L
 for Both end continuous
21

L
 for Cantilever
18

 Beam Width b = ( 0.3h- 0.6h )

ii. For Column ( Approximate Section ) (RC-M&D p530)

pu
 Ag (trial )  for Tied Column
0.40( f c'  f y  g )

pu
 Ag (trial )  for Spiral Column
0.50( f c'  f y  g )

 For Slab  f 
ln  0.8  y 
 0.2   fm  2 h  max(125mm,  1400 
)
36  5 ( fm  0.2)

 f 
ln  0.8  y 
h  max(90mm, 
1400 
  fm  2 )
36  9 

  fm  0.2 Use table 9.5(c)

Perimeter
 hmin 
180
Model File: 1, Revision 0
8/31/2018
Table of Contents

1. Structure Data 4

1.1 Story Data 4

1.2 Grid Data 4
1.3 Point Coordinates 4
1.4 Line Connectivity 9
1.5 Area Connectivity 22
1.6 Mass 24
1.7 Groups 24

2. Properties 25

2.1 Materials 25
2.2 Frame Sections 25
2.3 Shell Sections 25
2.4 Reinforcement Sizes 25
2.5 Tendon Sections 25

3. Assignments 26

3.1 Joint Assignments 26

3.2 Frame Assignments 32
3.3 Shell Assignments 46

4. Loads 47

4.1 Load Patterns 47

4.2 Auto Wind Loading 47
4.3 Applied Loads 50
4.3.1 Line Loads 50
4.3.2 Area Loads 60
4.4 Load Cases 61
4.5 Load Combinations 61

5. Analysis Results 63

5.1 Structure Results 63

5.2 Story Results 63
5.3 Point Results 72
5.4 Modal Results 79

Page 2 of 80
List of Tables

Table 1.1 Story Data 4

Table 1.2 Grid Systems 4
Table 1.3 Grid Lines 4
Table 1.4 Joint Coordinates Data 4
Table 1.5 Column Connectivity Data 9
Table 1.6 Beam Connectivity Data 12
Table 1.7 Brace Connectivity Data 15
Table 1.8 Floor Connectivity Data 22
Table 1.9 Null Shell Connectivity Data 23
Table 1.10 Mass Source 24
Table 1.11 Mass Summary by Story 24
Table 1.12 Group Definitions 24
Table 2.1 Material Properties - Summary 25
Table 2.2 Frame Sections - Summary 25
Table 2.3 Shell Sections - Summary 25
Table 2.4 Reinforcing Bar Sizes 25
Table 2.5 Tendon Section Properties 25
Table 3.1 Joint Assignments - Summary 26
Table 3.2 Frame Assignments - Summary 32
Table 3.3 Shell Assignments - Summary 46
Table 4.1 Load Patterns 47
Table 4.3 Frame Loads - Distributed 50
Table 4.4 Shell Loads - Uniform 60
Table 4.5 Load Cases - Summary 61
Table 4.6 Load Combinations 61
Table 5.1 Base Reactions 63
Table 5.2 Story Drifts 63
Table 5.3 Story Max/Avg Drifts 66
Table 5.4 Story Forces 69
Table 5.5 Joint Reactions 73
Table 5.6 Modal Periods and Frequencies 79
Table 5.7 Modal Participating Mass Ratios 79
Table 5.8 Modal Load Participation Ratios 80
Table 5.9 Modal Direction Factors 80

Page 3 of 80
Structure Data 8/31/2018

1 Structure Data
This chapter provides model geometry information, including items such as story levels, point coordinates, and
element connectivity.

1.1 Story Data

Table 1.1 - Story Data

Height Elevation Master Similar Splice

Name
mm mm Story To Story
Roof 3660 8160 No None No
Story1 500 4500 No None No
1F 3000 4000 No None No
GF 1000 1000 No None No
Base 0 0 No None No

1.2 Grid Data

Table 1.2 - Grid Systems

X Y Bubble
Story Rotation
Name Type Origin Origin Size Color
Range deg
m m mm
G1 Cartesian Default 0 0 0 1250 ffa0a0a0

Table 1.3 - Grid Lines

Grid Grid Bubble Ordinate

Grid ID Visible
System Direction Location m
G1 X E Yes End 0
G1 X D Yes End 3
G1 X C Yes End 6
G1 X B Yes End 9
G1 X A Yes End 12
G1 Y 1 Yes Start 0
G1 Y 2 Yes Start 2.5
G1 Y 3 Yes Start 5
G1 Y 4 Yes Start 7.5

1.3 Point Coordinates

Table 1.4 - Joint Coordinates Data

∆Z
X Y
Label Below
mm mm
mm
1 0 0 0
2 3000 0 0
3 6000 0 0
4 9000 0 0
5 12000 0 0
7 0 7500 0
8 3000 7500 0
9 6000 7500 0

Page 4 of 80
Structure Data 8/31/2018

Table 1.4 - Joint Coordinates Data (continued)

∆Z
X Y
Label Below
mm mm
mm
10 9000 7500 0
11 12000 7500 0
12 12000 2500 0
13 12000 5000 0
14 0 2500 0
15 0 5000 0
16 3000 5000 0
17 3000 2500 0
18 6000 2500 0
19 6000 5000 0
20 9000 5000 0
21 9000 2500 0
22 0 833.3 0
23 0 1666.7 0
24 0 3333.3 0
25 0 4166.7 0
26 0 5833.3 0
27 0 6666.7 0
28 12000 833.3 0
29 12000 1666.7 0
30 12000 3333.3 0
31 12000 4166.7 0
32 12000 5833.3 0
33 12000 6666.7 0
35 1000 0 0
36 2000 0 0
37 4000 0 0
38 5000 0 0
39 7000 0 0
40 8000 0 0
41 10000 0 0
42 11000 0 0
43 1000 7500 0
44 2000 7500 0
45 4000 7500 0
46 5000 7500 0
47 7000 7500 0
48 8000 7500 0
49 10000 7500 0
50 11000 7500 0
6 3000 3750 0
34 3000 3750 500
64 3000 1750 1952
67 3000 5750 1952

Page 5 of 80
Structure Data 8/31/2018

Table 1.4 - Joint Coordinates Data (continued)

∆Z
X Y
Label Below
mm mm
mm
70 3000 1750 2452
73 3000 5750 2452
76 6000 3750 0
77 6000 3750 500
79 6000 1750 1952
82 6000 5750 1952
85 6000 1750 2452
88 6000 5750 2452
91 9000 3750 0
92 9000 3750 500
94 9000 1750 1952
97 9000 5750 1952
100 9000 1750 2452
103 9000 5750 2452
106 10000 3750 0
107 10000 3750 500
109 10000 1750 1952
110 10000 2750 976
112 10000 5750 1952
113 10000 4750 976
115 10000 1750 2452
116 10000 2750 1476
118 10000 5750 2452
119 10000 4750 1476
120 10000 3750 1476
121 2000 3750 0
122 2000 3750 500
124 2000 1750 1952
125 2000 2750 976
127 2000 5750 1952
128 2000 4750 976
130 2000 1750 2452
131 2000 2750 1476
133 2000 5750 2452
134 2000 4750 1476
135 2000 3750 1476
136 4000 3750 500
137 5000 3750 500
138 4000 3750 0
139 5000 3750 0
140 7000 3750 0
141 8000 3750 0
142 7000 3750 500
143 8000 3750 500

Page 6 of 80
Structure Data 8/31/2018

Table 1.4 - Joint Coordinates Data (continued)

∆Z
X Y
Label Below
mm mm
mm
144 4000 1750 1952
145 5000 1750 1952
146 4000 1750 2452
147 5000 1750 2452
148 7000 1750 1952
149 8000 1750 1952
150 7000 1750 2452
151 8000 1750 2452
152 4000 5750 1952
153 5000 5750 1952
154 4000 5750 2452
155 5000 5750 2452
156 7000 5750 2452
157 8000 5750 2452
158 7000 5750 1952
159 8000 5750 1952
160 2000 2750 1952
161 2000 3750 1952
162 2000 4750 1952
163 2000 2750 2452
164 2000 3750 2452
165 2000 4750 2452
166 2000 2262.3 1952
167 2000 5237.7 1952
168 10000 2750 1952
169 10000 3750 1952
170 10000 4750 1952
171 10000 2750 2452
172 10000 3750 2452
173 10000 4750 2452
174 10000 2262.3 1952
175 10000 5237.7 1952
181 2000 4166.7 1952
182 2000 5000 1952
185 952.4 6666.7 2846.7
186 1904.8 5833.3 2033.3
187 2000 3333.3 1952
188 2000 2500 1952
191 952.4 833.3 2846.7
192 1904.8 1666.7 2033.3
195 2000 5237.7 2452
196 2000 2262.3 2452
197 10000 5237.7 2452
198 10000 2262.3 2452

Page 7 of 80
Structure Data 8/31/2018

Table 1.4 - Joint Coordinates Data (continued)

∆Z
X Y
Label Below
mm mm
mm
199 10000 4166.7 1952
200 10000 5000 1952
201 10000 3333.3 1952
202 10000 2500 1952
203 11047.6 833.3 2846.7
204 11047.6 6666.7 2846.7
205 10095.2 5833.3 2033.3
206 10095.2 1666.7 2033.3
207 11333.3 583.3 3090.7
208 10666.7 1166.7 2521.3
209 11333.3 583.3 3590.7
210 10666.7 1166.7 3021.3
211 11333.3 6916.7 3090.7
212 10666.7 6333.3 2521.3
213 11333.3 6916.7 3590.7
214 10666.7 6333.3 3021.3
215 666.7 6916.7 3090.7
216 1333.3 6333.3 2521.3
217 666.7 6916.7 3590.7
218 1333.3 6333.3 3021.3
219 666.7 583.3 3090.7
220 1333.3 1166.7 2521.3
221 666.7 583.3 3590.7
222 1333.3 1166.7 3021.3
57 3000 2450 1268.8
58 3000 3100 634.4
59 3000 5050 1268.8
60 3000 4400 634.4
61 3000 5050 1768.8
62 3000 4400 1134.4
108 3000 2450 1768.8
111 3000 3100 1134.4
178 3000 1150 3037.6
179 3000 550 3623.2
180 3000 6350 3037.6
183 3000 6950 3623.2
184 3000 550 3123.2
189 3000 1150 2537.6
190 3000 6950 3123.2
193 3000 6350 2537.6
194 6000 2450 1268.8
223 6000 3100 634.4
224 6000 5050 1268.8
225 6000 4400 634.4

Page 8 of 80
Structure Data 8/31/2018

Table 1.4 - Joint Coordinates Data (continued)

∆Z
X Y
Label Below
mm mm
mm
226 6000 5050 1768.8
227 6000 4400 1134.4
228 6000 2450 1768.8
229 6000 3100 1134.4
230 6000 1150 3037.6
231 6000 550 3623.2
232 6000 6350 3037.6
233 6000 6950 3623.2
234 6000 550 3123.2
235 6000 1150 2537.6
236 6000 6950 3123.2
237 6000 6350 2537.6
238 9000 2450 1268.8
239 9000 3100 634.4
240 9000 5050 1268.8
241 9000 4400 634.4
242 9000 5050 1768.8
243 9000 4400 1134.4
244 9000 2450 1768.8
245 9000 3100 1134.4
246 9000 1150 3037.6
247 9000 550 3623.2
248 9000 6350 3037.6
249 9000 6950 3623.2
250 9000 550 3123.2
251 9000 1150 2537.6
252 9000 6950 3123.2
253 9000 6350 2537.6
51 3000 3750 1134.4
52 6000 3750 1134.4
53 9000 3750 1134.4

1.4 Line Connectivity

Table 1.5 - Column Connectivity Data

I-End J-End I-End

Column
Point Point Story
C1 1 1 Below
C2 2 2 Below
C3 3 3 Below
C4 4 4 Below
C5 5 5 Below
C7 7 7 Below
C8 8 8 Below
C9 9 9 Below

Page 9 of 80
Structure Data 8/31/2018

Table 1.5 - Column Connectivity Data (continued)

I-End J-End I-End

Column
Point Point Story
C10 10 10 Below
C11 11 11 Below
C12 12 12 Below
C13 13 13 Below
C14 14 14 Below
C15 15 15 Below
C16 23 23 Below
C17 22 22 Below
C18 25 25 Below
C19 24 24 Below
C20 27 27 Below
C21 26 26 Below
C22 29 29 Below
C23 28 28 Below
C24 31 31 Below
C25 30 30 Below
C26 33 33 Below
C27 32 32 Below
C28 35 35 Below
C29 36 36 Below
C30 37 37 Below
C31 38 38 Below
C32 39 39 Below
C33 40 40 Below
C34 41 41 Below
C35 42 42 Below
C36 43 43 Below
C37 44 44 Below
C38 45 45 Below
C39 46 46 Below
C40 47 47 Below
C41 48 48 Below
C42 49 49 Below
C43 50 50 Below
C57 34 6 Same
C62 73 67 Same
C71 70 64 Same
C77 77 76 Same
C79 88 82 Same
C82 85 79 Same
C85 92 91 Same
C87 103 97 Same
C90 100 94 Same
C93 107 106 Same
C94 119 113 Same

Page 10 of 80
Structure Data 8/31/2018

Table 1.5 - Column Connectivity Data (continued)

I-End J-End I-End

Column
Point Point Story
C95 118 112 Same
C97 116 110 Same
C98 115 109 Same
C100 120 107 Same
C101 122 121 Same
C102 134 128 Same
C103 133 127 Same
C105 131 125 Same
C106 130 124 Same
C108 135 122 Same
C109 136 138 Same
C110 137 139 Same
C111 142 140 Same
C112 143 141 Same
C113 146 144 Same
C114 147 145 Same
C115 150 148 Same
C116 151 149 Same
C117 154 152 Same
C118 155 153 Same
C119 156 158 Same
C120 157 159 Same
C121 165 162 Same
C122 164 161 Same
C123 163 160 Same
C124 161 135 Same
C125 162 134 Same
C126 160 131 Same
C127 173 170 Same
C128 172 169 Same
C129 171 168 Same
C130 169 120 Same
C131 170 119 Same
C132 168 116 Same
C133 195 167 Same
C134 196 166 Same
C135 197 175 Same
C136 198 174 Same
C137 209 207 Same
C138 210 208 Same
C139 213 211 Same
C140 214 212 Same
C141 217 215 Same
C142 218 216 Same
C143 221 219 Same

Page 11 of 80
Structure Data 8/31/2018

Table 1.5 - Column Connectivity Data (continued)

I-End J-End I-End

Column
Point Point Story
C144 222 220 Same
C51 62 60 Same
C54 61 59 Same
C58 111 58 Same
C63 108 57 Same
C99 178 189 Same
C107 179 184 Same
C146 180 193 Same
C148 183 190 Same
C150 227 225 Same
C151 226 224 Same
C152 229 223 Same
C153 228 194 Same
C154 230 235 Same
C155 231 234 Same
C156 232 237 Same
C157 233 236 Same
C158 243 241 Same
C159 242 240 Same
C160 245 239 Same
C161 244 238 Same
C162 246 251 Same
C163 247 250 Same
C164 248 253 Same
C165 249 252 Same
C6 51 34 Same
C44 52 77 Same
C45 53 92 Same

Table 1.6 - Beam Connectivity Data

I-End J-End Curve

Beam
Point Point Type
B1 7 8 None
B2 8 9 None
B3 9 10 None
B4 10 11 None
B5 15 16 None
B6 14 17 None
B7 17 18 None
B8 16 19 None
B9 19 20 None
B10 18 21 None
B11 21 12 None
B12 20 13 None
B13 13 11 None

Page 12 of 80
Structure Data 8/31/2018

Table 1.6 - Beam Connectivity Data (continued)

I-End J-End Curve

Beam
Point Point Type
B14 12 13 None
B15 5 12 None
B16 4 5 None
B17 3 4 None
B18 2 3 None
B19 1 2 None
B20 1 14 None
B21 14 15 None
B22 15 7 None
B23 2 8 None
B24 3 9 None
B25 4 10 None
B26 1 22 None
B27 22 23 None
B28 23 14 None
B29 14 24 None
B30 24 25 None
B31 25 15 None
B32 15 26 None
B33 26 27 None
B34 27 7 None
B35 5 28 None
B36 28 29 None
B37 29 12 None
B38 12 30 None
B39 30 31 None
B40 31 13 None
B41 13 32 None
B42 32 33 None
B43 33 11 None
B45 1 35 None
B46 35 36 None
B47 36 2 None
B48 2 37 None
B49 37 38 None
B50 38 3 None
B51 3 39 None
B52 39 40 None
B53 40 4 None
B54 4 41 None
B55 41 42 None
B56 42 5 None
B57 7 43 None
B58 43 44 None
B59 44 8 None

Page 13 of 80
Structure Data 8/31/2018

Table 1.6 - Beam Connectivity Data (continued)

I-End J-End Curve

Beam
Point Point Type
B60 8 45 None
B61 45 46 None
B62 46 9 None
B63 9 47 None
B64 47 48 None
B65 48 10 None
B66 10 49 None
B67 49 50 None
B68 50 11 None
B71 116 119 None
B72 131 134 None
B73 121 6 None
B74 122 34 None
B78 91 106 None
B79 92 107 None
B81 34 136 None
B82 136 137 None
B83 137 77 None
B84 6 138 None
B85 138 139 None
B86 139 76 None
B87 76 140 None
B88 140 141 None
B89 141 91 None
B90 77 142 None
B91 142 143 None
B92 143 92 None
B93 130 70 None
B94 124 64 None
B98 94 109 None
B99 100 115 None
B101 64 144 None
B102 144 145 None
B103 145 79 None
B104 70 146 None
B105 146 147 None
B106 147 85 None
B107 79 148 None
B108 148 149 None
B109 149 94 None
B110 85 150 None
B111 150 151 None
B112 151 100 None
B113 133 73 None
B114 127 67 None

Page 14 of 80
Structure Data 8/31/2018

Table 1.6 - Beam Connectivity Data (continued)

I-End J-End Curve

Beam
Point Point Type
B115 97 112 None
B116 103 118 None
B117 67 152 None
B118 152 153 None
B119 153 82 None
B120 73 154 None
B121 154 155 None
B122 155 88 None
B123 82 158 None
B124 158 159 None
B125 159 97 None
B126 88 156 None
B127 156 157 None
B128 157 103 None
B132 160 161 None
B133 161 162 None
B135 130 163 None
B136 163 164 None
B137 164 165 None
B138 165 133 None
B139 124 166 None
B140 166 160 None
B141 162 167 None
B142 167 127 None
B143 168 169 None
B144 169 170 None
B145 115 171 None
B146 171 172 None
B147 172 173 None
B148 173 118 None
B149 109 174 None
B150 174 168 None
B151 170 175 None
B152 175 112 None
B44 111 62 None
B69 229 227 None
B70 245 243 None

Table 1.7 - Brace Connectivity Data

I-End J-End I-End

Brace
Point Point Story
D1 22 1 Below
D2 23 22 Below
D3 14 23 Below
D4 24 14 Below

Page 15 of 80
Structure Data 8/31/2018

Table 1.7 - Brace Connectivity Data (continued)

I-End J-End I-End

Brace
Point Point Story
D5 25 24 Below
D6 15 25 Below
D7 26 15 Below
D8 27 26 Below
D9 7 27 Below
D10 28 5 Below
D11 29 28 Below
D12 12 29 Below
D13 30 12 Below
D14 31 30 Below
D15 13 31 Below
D16 32 13 Below
D17 33 32 Below
D18 11 33 Below
D19 35 1 Below
D20 36 35 Below
D21 2 36 Below
D22 37 2 Below
D23 38 37 Below
D24 3 38 Below
D25 39 3 Below
D26 40 39 Below
D27 4 40 Below
D28 41 4 Below
D29 42 41 Below
D30 5 42 Below
D31 43 7 Below
D32 44 43 Below
D33 8 44 Below
D34 45 8 Below
D35 46 45 Below
D36 9 46 Below
D37 47 9 Below
D38 48 47 Below
D39 10 48 Below
D40 49 10 Below
D41 50 49 Below
D42 11 50 Below
D121 109 110 Same
D122 110 106 Same
D125 112 113 Same
D126 113 106 Same
D130 116 107 Same
D134 119 107 Same
D138 116 106 Same

Page 16 of 80
Structure Data 8/31/2018

Table 1.7 - Brace Connectivity Data (continued)

I-End J-End I-End

Brace
Point Point Story
D139 119 106 Same
D145 124 125 Same
D146 125 121 Same
D149 127 128 Same
D150 128 121 Same
D154 131 122 Same
D158 134 122 Same
D162 131 121 Same
D163 134 121 Same
D167 34 121 Same
D168 136 6 Same
D169 137 138 Same
D170 77 139 Same
D171 142 76 Same
D172 143 140 Same
D173 92 141 Same
D174 107 91 Same
D175 37 138 Below
D176 38 139 Below
D177 39 140 Below
D178 40 141 Below
D179 48 141 Below
D180 47 140 Below
D181 46 139 Below
D182 45 138 Below
D183 70 124 Same
D184 146 64 Same
D185 147 144 Same
D186 85 145 Same
D187 150 79 Same
D188 151 148 Same
D189 100 149 Same
D190 115 94 Same
D191 73 127 Same
D192 154 67 Same
D193 155 152 Same
D194 88 153 Same
D195 156 82 Same
D196 157 158 Same
D197 103 159 Same
D198 118 97 Same
D201 130 166 Same
D202 166 131 Same
D203 133 167 Same
D204 167 134 Same

Page 17 of 80
Structure Data 8/31/2018

Table 1.7 - Brace Connectivity Data (continued)

I-End J-End I-End

Brace
Point Point Story
D205 167 128 Same
D206 166 125 Same
D207 115 174 Same
D208 174 116 Same
D209 118 175 Same
D210 175 119 Same
D211 175 113 Same
D212 174 110 Same
D217 25 181 Below
D218 15 182 Below
D224 26 186 Below
D226 27 185 Below
D228 24 187 Below
D229 14 188 Below
D235 23 192 Below
D237 22 191 Below
D240 43 185 Below
D242 165 161 Same
D243 163 161 Same
D246 35 191 Below
D247 195 162 Same
D248 196 160 Same
D249 197 170 Same
D250 198 168 Same
D251 171 169 Same
D252 173 169 Same
D255 31 199 Below
D256 13 200 Below
D260 32 205 Below
D261 33 204 Below
D262 30 201 Below
D263 12 202 Below
D267 29 206 Below
D268 28 203 Below
D269 50 204 Below
D270 42 203 Below
D274 5 207 Below
D275 207 208 Same
D276 208 109 Same
D277 5 209 Same
D278 209 210 Same
D279 210 115 Same
D280 210 109 Same
D281 209 208 Same
D282 5 207 Same

Page 18 of 80
Structure Data 8/31/2018

Table 1.7 - Brace Connectivity Data (continued)

I-End J-End I-End

Brace
Point Point Story
D283 11 211 Below
D284 211 212 Same
D285 212 112 Same
D286 11 213 Same
D287 213 214 Same
D288 214 118 Same
D289 214 112 Same
D290 213 212 Same
D291 11 211 Same
D292 7 215 Below
D293 215 216 Same
D294 216 127 Same
D295 7 217 Same
D296 217 218 Same
D297 218 133 Same
D298 7 215 Same
D299 217 216 Same
D300 218 127 Same
D301 1 219 Below
D302 219 220 Same
D303 220 124 Same
D304 1 221 Same
D305 221 222 Same
D306 222 130 Same
D307 1 219 Same
D308 221 220 Same
D310 222 124 Same
D43 44 127 Below
D44 36 124 Below
D45 41 109 Below
D46 49 112 Below
D132 64 57 Same
D133 57 58 Same
D135 58 6 Same
D136 67 59 Same
D137 59 60 Same
D140 60 6 Same
D141 73 61 Same
D142 61 62 Same
D143 62 34 Same
D144 70 108 Same
D147 108 111 Same
D148 111 34 Same
D151 70 57 Same
D152 108 58 Same

Page 19 of 80
Structure Data 8/31/2018

Table 1.7 - Brace Connectivity Data (continued)

I-End J-End I-End

Brace
Point Point Story
D153 111 6 Same
D155 62 6 Same
D156 61 60 Same
D157 73 59 Same
D159 2 184 Below
D160 184 189 Same
D161 189 64 Same
D164 8 190 Below
D165 190 193 Same
D166 193 67 Same
D199 2 179 Same
D200 179 178 Same
D213 178 70 Same
D214 8 183 Same
D215 183 180 Same
D216 180 73 Same
D219 2 184 Same
D220 179 189 Same
D221 178 64 Same
D222 8 190 Same
D223 183 193 Same
D225 180 67 Same
D227 79 194 Same
D230 194 223 Same
D231 223 76 Same
D232 82 224 Same
D233 224 225 Same
D234 225 76 Same
D236 88 226 Same
D238 226 227 Same
D239 227 77 Same
D241 85 228 Same
D244 228 229 Same
D245 229 77 Same
D253 85 194 Same
D254 228 223 Same
D257 229 76 Same
D258 227 76 Same
D259 226 225 Same
D264 88 224 Same
D265 3 234 Below
D266 234 235 Same
D271 235 79 Same
D272 9 236 Below
D273 236 237 Same

Page 20 of 80
Structure Data 8/31/2018

Table 1.7 - Brace Connectivity Data (continued)

I-End J-End I-End

Brace
Point Point Story
D309 237 82 Same
D311 3 231 Same
D312 231 230 Same
D313 230 85 Same
D314 9 233 Same
D315 233 232 Same
D316 232 88 Same
D317 3 234 Same
D318 231 235 Same
D319 230 79 Same
D320 9 236 Same
D321 233 237 Same
D322 232 82 Same
D323 94 238 Same
D324 238 239 Same
D325 239 91 Same
D326 97 240 Same
D327 240 241 Same
D328 241 91 Same
D329 103 242 Same
D330 242 243 Same
D331 243 92 Same
D332 100 244 Same
D333 244 245 Same
D334 245 92 Same
D335 100 238 Same
D336 244 239 Same
D337 245 91 Same
D338 243 91 Same
D339 242 241 Same
D340 103 240 Same
D341 4 250 Below
D342 250 251 Same
D343 251 94 Same
D344 10 252 Below
D345 252 253 Same
D346 253 97 Same
D347 4 247 Same
D348 247 246 Same
D349 246 100 Same
D350 10 249 Same
D351 249 248 Same
D352 248 103 Same
D353 4 250 Same
D354 247 251 Same

Page 21 of 80
Structure Data 8/31/2018

Table 1.7 - Brace Connectivity Data (continued)

I-End J-End I-End

Brace
Point Point Story
D355 246 94 Same
D356 10 252 Same
D357 249 253 Same
D358 248 97 Same

1.5 Area Connectivity

Table 1.8 - Floor Connectivity Data

Number Edge Curve

Floor Point 1 Point 2
of Edges Number Type

F1 4 1 15 16 None
2 16 8 None
3 8 7 None
4 7 15 None
F2 4 1 14 17 None
2 17 16 None
3 16 15 None
4 15 14 None
F3 4 1 1 2 None
2 2 17 None
3 17 14 None
4 14 1 None
F4 4 1 2 3 None
2 3 18 None
3 18 17 None
4 17 2 None
F5 4 1 17 18 None
2 18 19 None
3 19 16 None
4 16 17 None
F6 4 1 16 19 None
2 19 9 None
3 9 8 None
4 8 16 None
F7 4 1 19 20 None
2 20 10 None
3 10 9 None
4 9 19 None
F8 4 1 18 21 None
2 21 20 None
3 20 19 None
4 19 18 None
F9 4 1 3 4 None
2 4 21 None
3 21 18 None

Page 22 of 80
Structure Data 8/31/2018

Table 1.8 - Floor Connectivity Data (continued)

Number Edge Curve

Floor Point 1 Point 2
of Edges Number Type

4 18 3 None
F10 4 1 4 5 None
2 5 12 None
3 12 21 None
4 21 4 None
F11 4 1 21 12 None
2 12 13 None
3 13 20 None
4 20 21 None
F12 4 1 20 13 None
2 13 11 None
3 11 10 None
4 10 20 None

Table 1.9 - Null Shell Connectivity Data

Number Edge Curve Point 1 Point 2

Label Point 1 Point 2
of Edges Number Type Story Story

A3 4 1 5 109 None Below Same

2 109 112 None Same Same
3 112 11 None Same Below
4 11 5 None Below Below
A4 3 1 109 106 None Same Same
2 106 112 None Same Same
3 112 109 None Same Same
A5 4 1 11 112 None Below Same
2 112 127 None Same Same
3 127 7 None Same Below
4 7 11 None Below Below
A6 4 1 112 106 None Same Same
2 106 121 None Same Same
3 121 127 None Same Same
4 127 112 None Same Same
A7 4 1 7 127 None Below Same
2 127 124 None Same Same
3 124 1 None Same Below
4 1 7 None Below Below
A8 3 1 127 121 None Same Same
2 121 124 None Same Same
3 124 127 None Same Same
A9 4 1 1 124 None Below Same
2 124 109 None Same Same
3 109 5 None Same Below
4 5 1 None Below Below
A10 4 1 124 121 None Same Same

Page 23 of 80
Structure Data 8/31/2018

Table 1.9 - Null Shell Connectivity Data (continued)

Number Edge Curve Point 1 Point 2

Label Point 1 Point 2
of Edges Number Type Story Story

2 121 106 None Same Same

3 106 109 None Same Same
4 109 124 None Same Same

1.6 Mass
Table 1.10 - Mass Source

Include Lump
Include Include Include Include
Name Added at IsDefault
Elements Loads Lateral Vertical
Mass Stories
MsSrc1 Yes Yes No Yes No Yes Yes

Table 1.11 - Mass Summary by Story

UX UY UZ
Story
kg kg kg
Roof 966.25 966.25 0
Story1 364.48 364.48 0
1F 4834.42 4834.42 0
GF 47686.01 47686.01 0
Base 1541.81 1541.81 0

1.7 Groups
Table 1.12 - Group Definitions

Name Color
All Yellow

Page 24 of 80
Properties 8/31/2018

2 Properties

This chapter provides property information for materials, frame sections, shell sections, and links.

2.1 Materials
Table 2.1 - Material Properties - Summary

Unit
E
Name Type ν Weight Design Strengths
MPa
kN/m³
A36 Steel 199947.98 0.3 76.9729 Fy=250 MPa, Fu=399.9 MPa
A416Gr270 Tendon 196500.6 0 76.9729 Fy=1689.91 MPa, Fu=1861.58 MPa
C25 Concrete 24855.58 0.2 24 Fc=25 MPa
SD390 Rebar 199947.98 0.3 76.9729 Fy=390 MPa, Fu=620.53 MPa

2.2 Frame Sections

Table 2.2 - Frame Sections - Summary

Name Material Shape

B25x30 C25 Concrete Rectangular
B25x50 C25 Concrete Rectangular
C30x30 C25 Concrete Rectangular
U&L chord A36 Steel Tube
W&P chord A36 Steel Tube

2.3 Shell Sections

Table 2.3 - Shell Sections - Summary

Total
Design Element
Name Material Thickness
Type Type
mm
S110 Slab Shell-Thin C25 110

2.4 Reinforcement Sizes

Table 2.4 - Reinforcing Bar Sizes

Diameter Area
Name
mm mm²
18 18 255

2.5 Tendon Sections

Table 2.5 - Tendon Section Properties

StrandArea
Name Material Color
mm²
Tendon1 A416Gr270 99 Aqua

Page 25 of 80
Assignments 8/31/2018

3 Assignments
This chapter provides a listing of the assignments applied to the model.
3.1 Joint Assignments
Table 3.1 - Joint Assignments - Summary

Unique
Story Label Diaphragm Restraints
Name
Roof 6 11 From Area
Roof 34 12 From Area
Roof 64 153 From Area
Roof 67 156 From Area
Roof 70 159 From Area
Roof 73 162 From Area
Roof 76 165 From Area
Roof 77 166 From Area
Roof 79 168 From Area
Roof 82 171 From Area
Roof 85 174 From Area
Roof 88 177 From Area
Roof 91 180 From Area
Roof 92 181 From Area
Roof 94 183 From Area
Roof 97 186 From Area
Roof 100 189 From Area
Roof 103 192 From Area
Roof 106 195 From Area
Roof 107 196 From Area
Roof 109 198 From Area
Roof 110 298 From Area
Roof 112 201 From Area
Roof 113 300 From Area
Roof 115 204 From Area
Roof 116 302 From Area
Roof 118 207 From Area
Roof 119 304 From Area
Roof 120 305 From Area
Roof 121 210 From Area
Roof 122 211 From Area
Roof 124 213 From Area
Roof 125 214 From Area
Roof 127 216 From Area
Roof 128 217 From Area
Roof 130 219 From Area
Roof 131 220 From Area
Roof 133 222 From Area
Roof 134 223 From Area
Roof 135 224 From Area
Roof 136 225 From Area

Page 26 of 80
Assignments 8/31/2018

Table 3.1 - Joint Assignments - Summary (continued)

Unique
Story Label Diaphragm Restraints
Name
Roof 137 226 From Area
Roof 138 227 From Area
Roof 139 228 From Area
Roof 140 229 From Area
Roof 141 230 From Area
Roof 142 231 From Area
Roof 143 232 From Area
Roof 144 233 From Area
Roof 145 234 From Area
Roof 146 235 From Area
Roof 147 236 From Area
Roof 148 237 From Area
Roof 149 238 From Area
Roof 150 239 From Area
Roof 151 240 From Area
Roof 152 241 From Area
Roof 153 242 From Area
Roof 154 243 From Area
Roof 155 244 From Area
Roof 156 245 From Area
Roof 157 246 From Area
Roof 158 247 From Area
Roof 159 248 From Area
Roof 160 249 From Area
Roof 161 250 From Area
Roof 162 251 From Area
Roof 163 252 From Area
Roof 164 253 From Area
Roof 165 254 From Area
Roof 166 255 From Area
Roof 167 256 From Area
Roof 168 306 From Area
Roof 169 307 From Area
Roof 170 308 From Area
Roof 171 309 From Area
Roof 172 310 From Area
Roof 173 311 From Area
Roof 174 312 From Area
Roof 175 313 From Area
Roof 181 279 From Area
Roof 182 280 From Area
Roof 185 283 From Area
Roof 186 284 From Area
Roof 187 285 From Area
Roof 188 286 From Area

Page 27 of 80
Assignments 8/31/2018

Table 3.1 - Joint Assignments - Summary (continued)

Unique
Story Label Diaphragm Restraints
Name
Roof 191 289 From Area
Roof 192 290 From Area
Roof 195 293 From Area
Roof 196 294 From Area
Roof 197 318 From Area
Roof 198 319 From Area
Roof 199 314 From Area
Roof 200 315 From Area
Roof 201 316 From Area
Roof 202 317 From Area
Roof 203 320 From Area
Roof 204 321 From Area
Roof 205 322 From Area
Roof 206 323 From Area
Roof 207 324 From Area
Roof 208 325 From Area
Roof 209 326 From Area
Roof 210 327 From Area
Roof 211 328 From Area
Roof 212 329 From Area
Roof 213 330 From Area
Roof 214 331 From Area
Roof 215 332 From Area
Roof 216 333 From Area
Roof 217 334 From Area
Roof 218 335 From Area
Roof 219 336 From Area
Roof 220 337 From Area
Roof 221 338 From Area
Roof 222 339 From Area
Roof 57 134 From Area
Roof 58 135 From Area
Roof 59 136 From Area
Roof 60 137 From Area
Roof 61 138 From Area
Roof 62 139 From Area
Roof 108 140 From Area
Roof 111 141 From Area
Roof 178 150 From Area
Roof 179 151 From Area
Roof 180 152 From Area
Roof 183 154 From Area
Roof 184 155 From Area
Roof 189 157 From Area
Roof 190 158 From Area

Page 28 of 80
Assignments 8/31/2018

Table 3.1 - Joint Assignments - Summary (continued)

Unique
Story Label Diaphragm Restraints
Name
Roof 193 160 From Area
Roof 194 161 From Area
Roof 223 163 From Area
Roof 224 164 From Area
Roof 225 167 From Area
Roof 226 169 From Area
Roof 227 170 From Area
Roof 228 172 From Area
Roof 229 173 From Area
Roof 230 175 From Area
Roof 231 176 From Area
Roof 232 178 From Area
Roof 233 179 From Area
Roof 234 197 From Area
Roof 235 199 From Area
Roof 236 200 From Area
Roof 237 202 From Area
Roof 238 203 From Area
Roof 239 205 From Area
Roof 240 206 From Area
Roof 241 208 From Area
Roof 242 209 From Area
Roof 243 212 From Area
Roof 244 215 From Area
Roof 245 218 From Area
Roof 246 221 From Area
Roof 247 257 From Area
Roof 248 258 From Area
Roof 249 259 From Area
Roof 250 260 From Area
Roof 251 261 From Area
Roof 252 262 From Area
Roof 253 263 From Area
Roof 51 51 From Area
Roof 52 52 From Area
Roof 53 53 From Area
Story1 1 57 From Area
Story1 2 91 From Area
Story1 3 96 From Area
Story1 4 101 From Area
Story1 5 73 From Area
Story1 7 72 From Area
Story1 8 110 From Area
Story1 9 115 From Area
Story1 10 120 From Area

Page 29 of 80
Assignments 8/31/2018

Table 3.1 - Joint Assignments - Summary (continued)

Unique
Story Label Diaphragm Restraints
Name
Story1 11 88 From Area
Story1 12 74 From Area
Story1 13 83 From Area
Story1 14 58 From Area
Story1 15 67 From Area
Story1 22 61 From Area
Story1 23 62 From Area
Story1 24 65 From Area
Story1 25 66 From Area
Story1 26 70 From Area
Story1 27 71 From Area
Story1 28 77 From Area
Story1 29 78 From Area
Story1 30 81 From Area
Story1 31 82 From Area
Story1 32 86 From Area
Story1 33 87 From Area
Story1 35 92 From Area
Story1 36 93 From Area
Story1 37 97 From Area
Story1 38 98 From Area
Story1 39 102 From Area
Story1 40 103 From Area
Story1 41 106 From Area
Story1 42 107 From Area
Story1 43 111 From Area
Story1 44 112 From Area
Story1 45 116 From Area
Story1 46 117 From Area
Story1 47 121 From Area
Story1 48 122 From Area
Story1 49 125 From Area
Story1 50 126 From Area
1F 1 37 From Area
1F 2 38 From Area
1F 3 39 From Area
1F 4 40 From Area
1F 5 41 From Area
1F 7 42 From Area
1F 8 43 From Area
1F 9 44 From Area
1F 10 45 From Area
1F 11 46 From Area
1F 12 47 From Area
1F 13 48 From Area

Page 30 of 80
Assignments 8/31/2018

Table 3.1 - Joint Assignments - Summary (continued)

Unique
Story Label Diaphragm Restraints
Name
1F 14 49 From Area
1F 15 50 From Area
1F 22 59 From Area
1F 23 60 From Area
1F 24 63 From Area
1F 25 64 From Area
1F 26 68 From Area
1F 27 69 From Area
1F 28 75 From Area
1F 29 76 From Area
1F 30 79 From Area
1F 31 80 From Area
1F 32 84 From Area
1F 33 85 From Area
1F 35 94 From Area
1F 36 95 From Area
1F 37 99 From Area
1F 38 100 From Area
1F 39 104 From Area
1F 40 105 From Area
1F 41 108 From Area
1F 42 109 From Area
1F 43 113 From Area
1F 44 114 From Area
1F 45 118 From Area
1F 46 119 From Area
1F 47 123 From Area
1F 48 124 From Area
1F 49 127 From Area
1F 50 128 From Area
GF 1 1 From Area
GF 2 3 From Area
GF 3 5 From Area
GF 4 7 From Area
GF 5 9 From Area
GF 7 13 From Area
GF 8 15 From Area
GF 9 17 From Area
GF 10 19 From Area
GF 11 21 From Area
GF 12 23 From Area
GF 13 25 From Area
GF 14 27 From Area
GF 15 29 From Area
GF 16 31 From Area

Page 31 of 80
Assignments 8/31/2018

Table 3.1 - Joint Assignments - Summary (continued)

Unique
Story Label Diaphragm Restraints
Name
GF 17 32 From Area
GF 18 33 From Area
GF 19 34 From Area
GF 20 35 From Area
GF 21 36 From Area
Base 1 2 From Area UX; UY; UZ
Base 2 4 From Area UX; UY; UZ; RX; RY; RZ
Base 3 6 From Area UX; UY; UZ; RX; RY; RZ
Base 4 8 From Area UX; UY; UZ; RX; RY; RZ
Base 5 10 From Area UX; UY; UZ
Base 7 14 From Area UX; UY; UZ
Base 8 16 From Area UX; UY; UZ; RX; RY; RZ
Base 9 18 From Area UX; UY; UZ; RX; RY; RZ
Base 10 20 From Area UX; UY; UZ; RX; RY; RZ
Base 11 22 From Area UX; UY; UZ
Base 12 24 From Area UX; UY; UZ
Base 13 26 From Area UX; UY; UZ
Base 14 28 From Area UX; UY; UZ
Base 15 30 From Area UX; UY; UZ

3.2 Frame Assignments

Table 3.2 - Frame Assignments - Summary

Max
Min
Unique Design Length Analysis Design Station
Story Label Number
Name Type mm Section Section Spacing
Stations
mm
Roof C57 256 Column 500 W&P chord W&P chord 3
Roof C62 261 Column 500 W&P chord W&P chord 3
Roof C71 270 Column 500 W&P chord W&P chord 3
Roof C77 363 Column 500 W&P chord W&P chord 3
Roof C79 364 Column 500 W&P chord W&P chord 3
Roof C82 365 Column 500 W&P chord W&P chord 3
Roof C85 521 Column 500 W&P chord W&P chord 3
Roof C87 524 Column 500 W&P chord W&P chord 3
Roof C90 545 Column 500 W&P chord W&P chord 3
Roof C93 658 Column 500 W&P chord W&P chord 3
Roof C94 659 Column 500 W&P chord W&P chord 3
Roof C95 660 Column 500 W&P chord W&P chord 3
Roof C97 662 Column 500 W&P chord W&P chord 3
Roof C98 663 Column 500 W&P chord W&P chord 3
Roof C100 672 Column 976 U&L chord U&L chord 3
Roof C101 400 Column 500 W&P chord W&P chord 3
Roof C102 401 Column 500 W&P chord W&P chord 3
Roof C103 402 Column 500 W&P chord W&P chord 3
Roof C105 404 Column 500 W&P chord W&P chord 3

Page 32 of 80
Assignments 8/31/2018

Table 3.2 - Frame Assignments - Summary (continued)

Max
Min
Unique Design Length Analysis Design Station
Story Label Number
Name Type mm Section Section Spacing
Stations
mm
Roof C106 405 Column 500 W&P chord W&P chord 3
Roof C108 416 Column 976 U&L chord U&L chord 3
Roof C109 439 Column 500 W&P chord W&P chord 3
Roof C110 441 Column 500 W&P chord W&P chord 3
Roof C111 444 Column 500 W&P chord W&P chord 3
Roof C112 446 Column 500 W&P chord W&P chord 3
Roof C113 479 Column 500 W&P chord W&P chord 3
Roof C114 481 Column 500 W&P chord W&P chord 3
Roof C115 484 Column 500 W&P chord W&P chord 3
Roof C116 486 Column 500 W&P chord W&P chord 3
Roof C117 507 Column 500 W&P chord W&P chord 3
Roof C118 509 Column 500 W&P chord W&P chord 3
Roof C119 512 Column 500 W&P chord W&P chord 3
Roof C120 514 Column 500 W&P chord W&P chord 3
Roof C121 529 Column 500 W&P chord W&P chord 3
Roof C122 530 Column 500 W&P chord W&P chord 3
Roof C123 531 Column 500 W&P chord W&P chord 3
Roof C124 540 Column 476 W&P chord W&P chord 3
Roof C125 541 Column 476 W&P chord W&P chord 3
Roof C126 542 Column 476 W&P chord W&P chord 3
Roof C127 679 Column 500 W&P chord W&P chord 3
Roof C128 680 Column 500 W&P chord W&P chord 3
Roof C129 681 Column 500 W&P chord W&P chord 3
Roof C130 690 Column 476 W&P chord W&P chord 3
Roof C131 691 Column 476 W&P chord W&P chord 3
Roof C132 692 Column 476 W&P chord W&P chord 3
Roof C133 630 Column 500 W&P chord W&P chord 3
Roof C134 632 Column 500 W&P chord W&P chord 3
Roof C135 697 Column 500 W&P chord W&P chord 3
Roof C136 699 Column 500 W&P chord W&P chord 3
Roof C137 725 Column 500 W&P chord W&P chord 3
Roof C138 726 Column 500 W&P chord W&P chord 3
Roof C139 736 Column 500 W&P chord W&P chord 3
Roof C140 737 Column 500 W&P chord W&P chord 3
Roof C141 748 Column 500 W&P chord W&P chord 3
Roof C142 750 Column 500 W&P chord W&P chord 3
Roof C143 759 Column 500 W&P chord W&P chord 3
Roof C144 762 Column 500 W&P chord W&P chord 3
Roof C51 242 Column 500 W&P chord W&P chord 3
Roof C54 246 Column 500 W&P chord W&P chord 3
Roof C58 250 Column 500 W&P chord W&P chord 3
Roof C63 254 Column 500 W&P chord W&P chord 3
Roof C99 281 Column 500 W&P chord W&P chord 3
Roof C107 283 Column 500 W&P chord W&P chord 3

Page 33 of 80
Assignments 8/31/2018

Table 3.2 - Frame Assignments - Summary (continued)

Max
Min
Unique Design Length Analysis Design Station
Story Label Number
Name Type mm Section Section Spacing
Stations
mm
Roof C146 351 Column 500 W&P chord W&P chord 3
Roof C148 353 Column 500 W&P chord W&P chord 3
Roof C150 378 Column 500 W&P chord W&P chord 3
Roof C151 379 Column 500 W&P chord W&P chord 3
Roof C152 380 Column 500 W&P chord W&P chord 3
Roof C153 381 Column 500 W&P chord W&P chord 3
Roof C154 419 Column 500 W&P chord W&P chord 3
Roof C155 420 Column 500 W&P chord W&P chord 3
Roof C156 421 Column 500 W&P chord W&P chord 3
Roof C157 424 Column 500 W&P chord W&P chord 3
Roof C158 558 Column 500 W&P chord W&P chord 3
Roof C159 559 Column 500 W&P chord W&P chord 3
Roof C160 560 Column 500 W&P chord W&P chord 3
Roof C161 561 Column 500 W&P chord W&P chord 3
Roof C162 580 Column 500 W&P chord W&P chord 3
Roof C163 581 Column 500 W&P chord W&P chord 3
Roof C164 582 Column 500 W&P chord W&P chord 3
Roof C165 583 Column 500 W&P chord W&P chord 3
Roof C6 55 Column 634.4 W&P chord W&P chord 3
Roof C44 131 Column 634.4 W&P chord W&P chord 3
Roof C45 133 Column 634.4 W&P chord W&P chord 3
Story1 C1 69 Column 500 U&L chord U&L chord 3
Story1 C2 145 Column 500 W&P chord W&P chord 3
Story1 C3 361 Column 500 W&P chord W&P chord 3
Story1 C4 519 Column 500 W&P chord W&P chord 3
Story1 C5 106 Column 500 U&L chord U&L chord 3
Story1 C7 93 Column 500 W&P chord W&P chord 3
Story1 C8 192 Column 500 W&P chord W&P chord 3
Story1 C9 362 Column 500 W&P chord W&P chord 3
Story1 C10 520 Column 500 W&P chord W&P chord 3
Story1 C11 130 Column 500 W&P chord W&P chord 3
Story1 C12 104 Column 500 U&L chord U&L chord 3
Story1 C13 129 Column 500 W&P chord W&P chord 3
Story1 C14 67 Column 500 U&L chord U&L chord 3
Story1 C15 92 Column 500 W&P chord W&P chord 3
Story1 C16 65 Column 500 W&P chord W&P chord 3
Story1 C17 68 Column 500 W&P chord W&P chord 3
Story1 C18 78 Column 500 W&P chord W&P chord 3
Story1 C19 80 Column 500 W&P chord W&P chord 3
Story1 C20 89 Column 500 W&P chord W&P chord 3
Story1 C21 91 Column 500 W&P chord W&P chord 3
Story1 C22 102 Column 500 W&P chord W&P chord 3
Story1 C23 105 Column 500 W&P chord W&P chord 3
Story1 C24 115 Column 500 W&P chord W&P chord 3

Page 34 of 80
Assignments 8/31/2018

Table 3.2 - Frame Assignments - Summary (continued)

Max
Min
Unique Design Length Analysis Design Station
Story Label Number
Name Type mm Section Section Spacing
Stations
mm
Story1 C25 117 Column 500 W&P chord W&P chord 3
Story1 C26 126 Column 500 W&P chord W&P chord 3
Story1 C27 128 Column 500 W&P chord W&P chord 3
Story1 C28 141 Column 500 W&P chord W&P chord 3
Story1 C29 143 Column 500 W&P chord W&P chord 3
Story1 C30 153 Column 500 W&P chord W&P chord 3
Story1 C31 155 Column 500 W&P chord W&P chord 3
Story1 C32 165 Column 500 W&P chord W&P chord 3
Story1 C33 167 Column 500 W&P chord W&P chord 3
Story1 C34 642 Column 500 W&P chord W&P chord 3
Story1 C35 179 Column 500 W&P chord W&P chord 3
Story1 C36 188 Column 500 W&P chord W&P chord 3
Story1 C37 190 Column 500 W&P chord W&P chord 3
Story1 C38 200 Column 500 W&P chord W&P chord 3
Story1 C39 202 Column 500 W&P chord W&P chord 3
Story1 C40 212 Column 500 W&P chord W&P chord 3
Story1 C41 214 Column 500 W&P chord W&P chord 3
Story1 C42 643 Column 500 W&P chord W&P chord 3
Story1 C43 226 Column 500 W&P chord W&P chord 3
1F C1 41 Column 3000 C30x30 C30x30 3
1F C2 42 Column 3000 C30x30 C30x30 3
1F C3 43 Column 3000 C30x30 C30x30 3
1F C4 44 Column 3000 C30x30 C30x30 3
1F C5 45 Column 3000 C30x30 C30x30 3
1F C7 46 Column 3000 C30x30 C30x30 3
1F C8 47 Column 3000 C30x30 C30x30 3
1F C9 48 Column 3000 C30x30 C30x30 3
1F C10 49 Column 3000 C30x30 C30x30 3
1F C11 50 Column 3000 C30x30 C30x30 3
1F C12 51 Column 3000 C30x30 C30x30 3
1F C13 52 Column 3000 C30x30 C30x30 3
1F C14 53 Column 3000 C30x30 C30x30 3
1F C15 54 Column 3000 C30x30 C30x30 3
GF C1 1 Column 1000 C30x30 C30x30 3
GF C2 2 Column 1000 C30x30 C30x30 3
GF C3 3 Column 1000 C30x30 C30x30 3
GF C4 4 Column 1000 C30x30 C30x30 3
GF C5 5 Column 1000 C30x30 C30x30 3
GF C7 7 Column 1000 C30x30 C30x30 3
GF C8 8 Column 1000 C30x30 C30x30 3
GF C9 9 Column 1000 C30x30 C30x30 3
GF C10 10 Column 1000 C30x30 C30x30 3
GF C11 11 Column 1000 C30x30 C30x30 3
GF C12 12 Column 1000 C30x30 C30x30 3

Page 35 of 80
Assignments 8/31/2018

Table 3.2 - Frame Assignments - Summary (continued)

Max
Min
Unique Design Length Analysis Design Station
Story Label Number
Name Type mm Section Section Spacing
Stations
mm
GF C13 13 Column 1000 C30x30 C30x30 3
GF C14 14 Column 1000 C30x30 C30x30 3
GF C15 15 Column 1000 C30x30 C30x30 3
Roof B71 671 Beam 2000 U&L chord U&L chord 500
Roof B72 415 Beam 2000 U&L chord U&L chord 500
Roof B73 417 Beam 1000 U&L chord U&L chord 500
Roof B74 418 Beam 1000 U&L chord U&L chord 500
Roof B78 422 Beam 1000 U&L chord U&L chord 500
Roof B79 423 Beam 1000 U&L chord U&L chord 500
Roof B81 425 Beam 1000 U&L chord U&L chord 500
Roof B82 426 Beam 1000 U&L chord U&L chord 500
Roof B83 427 Beam 1000 U&L chord U&L chord 500
Roof B84 428 Beam 1000 U&L chord U&L chord 500
Roof B85 429 Beam 1000 U&L chord U&L chord 500
Roof B86 430 Beam 1000 U&L chord U&L chord 500
Roof B87 431 Beam 1000 U&L chord U&L chord 500
Roof B88 432 Beam 1000 U&L chord U&L chord 500
Roof B89 433 Beam 1000 U&L chord U&L chord 500
Roof B90 434 Beam 1000 U&L chord U&L chord 500
Roof B91 435 Beam 1000 U&L chord U&L chord 500
Roof B92 436 Beam 1000 U&L chord U&L chord 500
Roof B93 457 Beam 1000 W&P chord W&P chord 500
Roof B94 458 Beam 1000 W&P chord W&P chord 500
Roof B98 462 Beam 1000 W&P chord W&P chord 500
Roof B99 463 Beam 1000 W&P chord W&P chord 500
Roof B101 466 Beam 1000 W&P chord W&P chord 500
Roof B102 467 Beam 1000 W&P chord W&P chord 500
Roof B103 468 Beam 1000 W&P chord W&P chord 500
Roof B104 469 Beam 1000 W&P chord W&P chord 500
Roof B105 470 Beam 1000 W&P chord W&P chord 500
Roof B106 471 Beam 1000 W&P chord W&P chord 500
Roof B107 472 Beam 1000 W&P chord W&P chord 500
Roof B108 473 Beam 1000 W&P chord W&P chord 500
Roof B109 474 Beam 1000 W&P chord W&P chord 500
Roof B110 475 Beam 1000 W&P chord W&P chord 500
Roof B111 476 Beam 1000 W&P chord W&P chord 500
Roof B112 477 Beam 1000 W&P chord W&P chord 500
Roof B113 489 Beam 1000 W&P chord W&P chord 500
Roof B114 490 Beam 1000 W&P chord W&P chord 500
Roof B115 491 Beam 1000 W&P chord W&P chord 500
Roof B116 492 Beam 1000 W&P chord W&P chord 500
Roof B117 494 Beam 1000 W&P chord W&P chord 500
Roof B118 495 Beam 1000 W&P chord W&P chord 500
Roof B119 496 Beam 1000 W&P chord W&P chord 500

Page 36 of 80
Assignments 8/31/2018

Table 3.2 - Frame Assignments - Summary (continued)

Max
Min
Unique Design Length Analysis Design Station
Story Label Number
Name Type mm Section Section Spacing
Stations
mm
Roof B120 497 Beam 1000 W&P chord W&P chord 500
Roof B121 498 Beam 1000 W&P chord W&P chord 500
Roof B122 499 Beam 1000 W&P chord W&P chord 500
Roof B123 500 Beam 1000 W&P chord W&P chord 500
Roof B124 501 Beam 1000 W&P chord W&P chord 500
Roof B125 502 Beam 1000 W&P chord W&P chord 500
Roof B126 503 Beam 1000 W&P chord W&P chord 500
Roof B127 504 Beam 1000 W&P chord W&P chord 500
Roof B128 505 Beam 1000 W&P chord W&P chord 500
Roof B132 522 Beam 1000 U&L chord U&L chord 500
Roof B133 523 Beam 1000 U&L chord U&L chord 500
Roof B135 525 Beam 1000 U&L chord U&L chord 500
Roof B136 526 Beam 1000 U&L chord U&L chord 500
Roof B137 527 Beam 1000 U&L chord U&L chord 500
Roof B138 528 Beam 1000 U&L chord U&L chord 500
Roof B139 536 Beam 512.3 U&L chord U&L chord 500
Roof B140 537 Beam 487.7 U&L chord U&L chord 500
Roof B141 538 Beam 487.7 U&L chord U&L chord 500
Roof B142 539 Beam 512.3 U&L chord U&L chord 500
Roof B143 673 Beam 1000 U&L chord U&L chord 500
Roof B144 674 Beam 1000 U&L chord U&L chord 500
Roof B145 675 Beam 1000 U&L chord U&L chord 500
Roof B146 676 Beam 1000 U&L chord U&L chord 500
Roof B147 677 Beam 1000 U&L chord U&L chord 500
Roof B148 678 Beam 1000 U&L chord U&L chord 500
Roof B149 686 Beam 512.3 U&L chord U&L chord 500
Roof B150 687 Beam 487.7 U&L chord U&L chord 500
Roof B151 688 Beam 487.7 U&L chord U&L chord 500
Roof B152 689 Beam 512.3 U&L chord U&L chord 500
Roof B44 6 Beam 1300 W&P chord W&P chord 500
Roof B69 56 Beam 1300 W&P chord W&P chord 500
Roof B70 132 Beam 1300 W&P chord W&P chord 500
Story1 B26 60 Beam 833.3 U&L chord U&L chord 500
Story1 B27 61 Beam 833.3 U&L chord U&L chord 500
Story1 B28 62 Beam 833.3 U&L chord U&L chord 500
Story1 B29 73 Beam 833.3 U&L chord U&L chord 500
Story1 B30 74 Beam 833.3 U&L chord U&L chord 500
Story1 B31 75 Beam 833.3 U&L chord U&L chord 500
Story1 B32 84 Beam 833.3 U&L chord U&L chord 500
Story1 B33 85 Beam 833.3 U&L chord U&L chord 500
Story1 B34 86 Beam 833.3 U&L chord U&L chord 500
Story1 B35 97 Beam 833.3 U&L chord U&L chord 500
Story1 B36 98 Beam 833.3 U&L chord U&L chord 500
Story1 B37 99 Beam 833.3 U&L chord U&L chord 500

Page 37 of 80
Assignments 8/31/2018

Table 3.2 - Frame Assignments - Summary (continued)

Max
Min
Unique Design Length Analysis Design Station
Story Label Number
Name Type mm Section Section Spacing
Stations
mm
Story1 B38 110 Beam 833.3 U&L chord U&L chord 500
Story1 B39 111 Beam 833.3 U&L chord U&L chord 500
Story1 B40 112 Beam 833.3 U&L chord U&L chord 500
Story1 B41 121 Beam 833.3 U&L chord U&L chord 500
Story1 B42 122 Beam 833.3 U&L chord U&L chord 500
Story1 B43 123 Beam 833.3 U&L chord U&L chord 500
Story1 B45 134 Beam 1000 U&L chord U&L chord 500
Story1 B46 135 Beam 1000 U&L chord U&L chord 500
Story1 B47 136 Beam 1000 U&L chord U&L chord 500
Story1 B48 146 Beam 1000 U&L chord U&L chord 500
Story1 B49 147 Beam 1000 U&L chord U&L chord 500
Story1 B50 148 Beam 1000 U&L chord U&L chord 500
Story1 B51 158 Beam 1000 U&L chord U&L chord 500
Story1 B52 159 Beam 1000 U&L chord U&L chord 500
Story1 B53 160 Beam 1000 U&L chord U&L chord 500
Story1 B54 170 Beam 1000 U&L chord U&L chord 500
Story1 B55 171 Beam 1000 U&L chord U&L chord 500
Story1 B56 172 Beam 1000 U&L chord U&L chord 500
Story1 B57 181 Beam 1000 U&L chord U&L chord 500
Story1 B58 182 Beam 1000 U&L chord U&L chord 500
Story1 B59 183 Beam 1000 U&L chord U&L chord 500
Story1 B60 193 Beam 1000 U&L chord U&L chord 500
Story1 B61 194 Beam 1000 U&L chord U&L chord 500
Story1 B62 195 Beam 1000 U&L chord U&L chord 500
Story1 B63 205 Beam 1000 U&L chord U&L chord 500
Story1 B64 206 Beam 1000 U&L chord U&L chord 500
Story1 B65 207 Beam 1000 U&L chord U&L chord 500
Story1 B66 217 Beam 1000 U&L chord U&L chord 500
Story1 B67 218 Beam 1000 U&L chord U&L chord 500
Story1 B68 219 Beam 1000 U&L chord U&L chord 500
1F B26 57 Beam 833.3 U&L chord U&L chord 500
1F B27 58 Beam 833.3 U&L chord U&L chord 500
1F B28 59 Beam 833.3 U&L chord U&L chord 500
1F B29 70 Beam 833.3 U&L chord U&L chord 500
1F B30 71 Beam 833.3 U&L chord U&L chord 500
1F B31 72 Beam 833.3 U&L chord U&L chord 500
1F B32 81 Beam 833.3 U&L chord U&L chord 500
1F B33 82 Beam 833.3 U&L chord U&L chord 500
1F B34 83 Beam 833.3 U&L chord U&L chord 500
1F B35 94 Beam 833.3 U&L chord U&L chord 500
1F B36 95 Beam 833.3 U&L chord U&L chord 500
1F B37 96 Beam 833.3 U&L chord U&L chord 500
1F B38 107 Beam 833.3 U&L chord U&L chord 500
1F B39 108 Beam 833.3 U&L chord U&L chord 500

Page 38 of 80
Assignments 8/31/2018

Table 3.2 - Frame Assignments - Summary (continued)

Max
Min
Unique Design Length Analysis Design Station
Story Label Number
Name Type mm Section Section Spacing
Stations
mm
1F B40 109 Beam 833.3 U&L chord U&L chord 500
1F B41 118 Beam 833.3 U&L chord U&L chord 500
1F B42 119 Beam 833.3 U&L chord U&L chord 500
1F B43 120 Beam 833.3 U&L chord U&L chord 500
1F B45 137 Beam 1000 U&L chord U&L chord 500
1F B46 138 Beam 1000 U&L chord U&L chord 500
1F B47 139 Beam 1000 U&L chord U&L chord 500
1F B48 149 Beam 1000 U&L chord U&L chord 500
1F B49 150 Beam 1000 U&L chord U&L chord 500
1F B50 151 Beam 1000 U&L chord U&L chord 500
1F B51 161 Beam 1000 U&L chord U&L chord 500
1F B52 162 Beam 1000 U&L chord U&L chord 500
1F B53 163 Beam 1000 U&L chord U&L chord 500
1F B54 173 Beam 1000 U&L chord U&L chord 500
1F B55 174 Beam 1000 U&L chord U&L chord 500
1F B56 175 Beam 1000 U&L chord U&L chord 500
1F B57 184 Beam 1000 U&L chord U&L chord 500
1F B58 185 Beam 1000 U&L chord U&L chord 500
1F B59 186 Beam 1000 U&L chord U&L chord 500
1F B60 196 Beam 1000 U&L chord U&L chord 500
1F B61 197 Beam 1000 U&L chord U&L chord 500
1F B62 198 Beam 1000 U&L chord U&L chord 500
1F B63 208 Beam 1000 U&L chord U&L chord 500
1F B64 209 Beam 1000 U&L chord U&L chord 500
1F B65 210 Beam 1000 U&L chord U&L chord 500
1F B66 220 Beam 1000 U&L chord U&L chord 500
1F B67 221 Beam 1000 U&L chord U&L chord 500
1F B68 222 Beam 1000 U&L chord U&L chord 500
GF B1 16 Beam 3000 B25x30 B25x30 500
GF B2 17 Beam 3000 B25x30 B25x30 500
GF B3 18 Beam 3000 B25x30 B25x30 500
GF B4 19 Beam 3000 B25x30 B25x30 500
GF B5 20 Beam 3000 B25x30 B25x30 500
GF B6 21 Beam 3000 B25x30 B25x30 500
GF B7 22 Beam 3000 B25x30 B25x30 500
GF B8 23 Beam 3000 B25x30 B25x30 500
GF B9 24 Beam 3000 B25x30 B25x30 500
GF B10 25 Beam 3000 B25x30 B25x30 500
GF B11 26 Beam 3000 B25x30 B25x30 500
GF B12 27 Beam 3000 B25x30 B25x30 500
GF B13 28 Beam 2500 B25x30 B25x30 500
GF B14 29 Beam 2500 B25x30 B25x30 500
GF B15 30 Beam 2500 B25x30 B25x30 500
GF B16 31 Beam 3000 B25x30 B25x30 500

Page 39 of 80
Assignments 8/31/2018

Table 3.2 - Frame Assignments - Summary (continued)

Max
Min
Unique Design Length Analysis Design Station
Story Label Number
Name Type mm Section Section Spacing
Stations
mm
GF B17 32 Beam 3000 B25x30 B25x30 500
GF B18 33 Beam 3000 B25x30 B25x30 500
GF B19 34 Beam 3000 B25x30 B25x30 500
GF B20 35 Beam 2500 B25x30 B25x30 500
GF B21 36 Beam 2500 B25x30 B25x30 500
GF B22 37 Beam 2500 B25x30 B25x30 500
GF B23 38 Beam 7500 B25x50 B25x50 500
GF B24 39 Beam 7500 B25x50 B25x50 500
GF B25 40 Beam 7500 B25x50 B25x50 500
Roof D121 646 Brace 1397.3 U&L chord U&L chord 3
Roof D122 647 Brace 1397.3 U&L chord U&L chord 3
Roof D125 650 Brace 1397.3 U&L chord U&L chord 3
Roof D126 651 Brace 1397.3 U&L chord U&L chord 3
Roof D130 654 Brace 1397.3 U&L chord U&L chord 3
Roof D134 657 Brace 1397.3 U&L chord U&L chord 3
Roof D138 667 Brace 1782.9 W&P chord W&P chord 3
Roof D139 668 Brace 1782.9 W&P chord W&P chord 3
Roof D145 386 Brace 1397.3 U&L chord U&L chord 3
Roof D146 387 Brace 1397.3 U&L chord U&L chord 3
Roof D149 390 Brace 1397.3 U&L chord U&L chord 3
Roof D150 391 Brace 1397.3 U&L chord U&L chord 3
Roof D154 395 Brace 1397.3 U&L chord U&L chord 3
Roof D158 399 Brace 1397.3 U&L chord U&L chord 3
Roof D162 410 Brace 1782.9 W&P chord W&P chord 3
Roof D163 411 Brace 1782.9 W&P chord W&P chord 3
Roof D167 437 Brace 1118 W&P chord W&P chord 3
Roof D168 438 Brace 1118 W&P chord W&P chord 3
Roof D169 440 Brace 1118 W&P chord W&P chord 3
Roof D170 442 Brace 1118 W&P chord W&P chord 3
Roof D171 443 Brace 1118 W&P chord W&P chord 3
Roof D172 445 Brace 1118 W&P chord W&P chord 3
Roof D173 447 Brace 1118 W&P chord W&P chord 3
Roof D174 448 Brace 1118 W&P chord W&P chord 3
Roof D175 449 Brace 5240 U&L chord U&L chord 3
Roof D176 450 Brace 5240 U&L chord U&L chord 3
Roof D177 451 Brace 5240 U&L chord U&L chord 3
Roof D178 452 Brace 5240 U&L chord U&L chord 3
Roof D179 453 Brace 5240 U&L chord U&L chord 3
Roof D180 454 Brace 5240 U&L chord U&L chord 3
Roof D181 455 Brace 5240 U&L chord U&L chord 3
Roof D182 456 Brace 5240 U&L chord U&L chord 3
Roof D183 465 Brace 1118 W&P chord W&P chord 3
Roof D184 478 Brace 1118 W&P chord W&P chord 3
Roof D185 480 Brace 1118 W&P chord W&P chord 3

Page 40 of 80
Assignments 8/31/2018

Table 3.2 - Frame Assignments - Summary (continued)

Max
Min
Unique Design Length Analysis Design Station
Story Label Number
Name Type mm Section Section Spacing
Stations
mm
Roof D186 482 Brace 1118 W&P chord W&P chord 3
Roof D187 483 Brace 1118 W&P chord W&P chord 3
Roof D188 485 Brace 1118 W&P chord W&P chord 3
Roof D189 487 Brace 1118 W&P chord W&P chord 3
Roof D190 488 Brace 1118 W&P chord W&P chord 3
Roof D191 493 Brace 1118 W&P chord W&P chord 3
Roof D192 506 Brace 1118 W&P chord W&P chord 3
Roof D193 508 Brace 1118 W&P chord W&P chord 3
Roof D194 510 Brace 1118 W&P chord W&P chord 3
Roof D195 511 Brace 1118 W&P chord W&P chord 3
Roof D196 513 Brace 1118 W&P chord W&P chord 3
Roof D197 515 Brace 1118 W&P chord W&P chord 3
Roof D198 516 Brace 1118 W&P chord W&P chord 3
Roof D201 532 Brace 715.9 U&L chord U&L chord 3
Roof D202 533 Brace 681.5 U&L chord U&L chord 3
Roof D203 534 Brace 715.9 U&L chord U&L chord 3
Roof D204 535 Brace 681.5 U&L chord U&L chord 3
Roof D205 543 Brace 1091.1 W&P chord W&P chord 3
Roof D206 544 Brace 1091.1 W&P chord W&P chord 3
Roof D207 682 Brace 715.9 U&L chord U&L chord 3
Roof D208 683 Brace 681.5 U&L chord U&L chord 3
Roof D209 684 Brace 715.9 U&L chord U&L chord 3
Roof D210 685 Brace 681.5 U&L chord U&L chord 3
Roof D211 693 Brace 1091.1 W&P chord W&P chord 3
Roof D212 694 Brace 1091.1 W&P chord W&P chord 3
Roof D217 602 Brace 2630.1 U&L chord U&L chord 3
Roof D218 603 Brace 2630.1 U&L chord U&L chord 3
Roof D224 609 Brace 2504.8 U&L chord U&L chord 3
Roof D226 611 Brace 1252.4 U&L chord U&L chord 3
Roof D228 613 Brace 2630.1 U&L chord U&L chord 3
Roof D229 614 Brace 2630.1 U&L chord U&L chord 3
Roof D235 620 Brace 2504.8 U&L chord U&L chord 3
Roof D237 622 Brace 1252.4 U&L chord U&L chord 3
Roof D240 624 Brace 1165.4 U&L chord U&L chord 3
Roof D242 626 Brace 1118 W&P chord W&P chord 3
Roof D243 627 Brace 1118 W&P chord W&P chord 3
Roof D246 629 Brace 1165.4 U&L chord U&L chord 3
Roof D247 631 Brace 698.5 W&P chord W&P chord 3
Roof D248 633 Brace 698.5 W&P chord W&P chord 3
Roof D249 698 Brace 698.5 W&P chord W&P chord 3
Roof D250 700 Brace 698.5 W&P chord W&P chord 3
Roof D251 696 Brace 1118 W&P chord W&P chord 3
Roof D252 695 Brace 1118 W&P chord W&P chord 3
Roof D255 701 Brace 2630.1 U&L chord U&L chord 3

Page 41 of 80
Assignments 8/31/2018

Table 3.2 - Frame Assignments - Summary (continued)

Max
Min
Unique Design Length Analysis Design Station
Story Label Number
Name Type mm Section Section Spacing
Stations
mm
Roof D256 702 Brace 2630.1 U&L chord U&L chord 3
Roof D260 706 Brace 2504.8 U&L chord U&L chord 3
Roof D261 707 Brace 1252.4 U&L chord U&L chord 3
Roof D262 708 Brace 2630.1 U&L chord U&L chord 3
Roof D263 709 Brace 2630.1 U&L chord U&L chord 3
Roof D267 713 Brace 2504.8 U&L chord U&L chord 3
Roof D268 714 Brace 1252.4 U&L chord U&L chord 3
Roof D269 715 Brace 1165.4 U&L chord U&L chord 3
Roof D270 716 Brace 1165.4 U&L chord U&L chord 3
Roof D274 719 Brace 1053 U&L chord U&L chord 3
Roof D275 720 Brace 1053 U&L chord U&L chord 3
Roof D276 721 Brace 1053 U&L chord U&L chord 3
Roof D277 722 Brace 1053 U&L chord U&L chord 3
Roof D278 723 Brace 1053 U&L chord U&L chord 3
Roof D279 724 Brace 1053 U&L chord U&L chord 3
Roof D280 727 Brace 1388.6 W&P chord W&P chord 3
Roof D281 728 Brace 1388.6 W&P chord W&P chord 3
Roof D282 729 Brace 1388.6 W&P chord W&P chord 3
Roof D283 730 Brace 1053 U&L chord U&L chord 3
Roof D284 731 Brace 1053 U&L chord U&L chord 3
Roof D285 732 Brace 1053 U&L chord U&L chord 3
Roof D286 733 Brace 1053 U&L chord U&L chord 3
Roof D287 734 Brace 1053 U&L chord U&L chord 3
Roof D288 735 Brace 1053 U&L chord U&L chord 3
Roof D289 738 Brace 1388.6 W&P chord W&P chord 3
Roof D290 739 Brace 1388.6 W&P chord W&P chord 3
Roof D291 740 Brace 1388.6 W&P chord W&P chord 3
Roof D292 741 Brace 1053 U&L chord U&L chord 3
Roof D293 742 Brace 1053 U&L chord U&L chord 3
Roof D294 743 Brace 1053 U&L chord U&L chord 3
Roof D295 744 Brace 1053 U&L chord U&L chord 3
Roof D296 745 Brace 1053 U&L chord U&L chord 3
Roof D297 746 Brace 1053 U&L chord U&L chord 3
Roof D298 747 Brace 1388.6 W&P chord W&P chord 3
Roof D299 749 Brace 1388.6 W&P chord W&P chord 3
Roof D300 751 Brace 1388.6 W&P chord W&P chord 3
Roof D301 752 Brace 1053 U&L chord U&L chord 3
Roof D302 753 Brace 1053 U&L chord U&L chord 3
Roof D303 754 Brace 1053 U&L chord U&L chord 3
Roof D304 755 Brace 1053 U&L chord U&L chord 3
Roof D305 756 Brace 1053 U&L chord U&L chord 3
Roof D306 757 Brace 1053 U&L chord U&L chord 3
Roof D307 758 Brace 1388.6 W&P chord W&P chord 3
Roof D308 760 Brace 1388.6 W&P chord W&P chord 3

Page 42 of 80
Assignments 8/31/2018

Table 3.2 - Frame Assignments - Summary (continued)

Max
Min
Unique Design Length Analysis Design Station
Story Label Number
Name Type mm Section Section Spacing
Stations
mm
Roof D310 763 Brace 1388.6 W&P chord W&P chord 3
Roof D43 389 Brace 2445.4 U&L chord U&L chord 3
Roof D44 385 Brace 2445.4 U&L chord U&L chord 3
Roof D45 645 Brace 2445.4 U&L chord U&L chord 3
Roof D46 649 Brace 2445.4 U&L chord U&L chord 3
Roof D132 228 Brace 978.1 U&L chord U&L chord 3
Roof D133 229 Brace 908.3 U&L chord U&L chord 3
Roof D135 230 Brace 908.3 U&L chord U&L chord 3
Roof D136 231 Brace 978.1 U&L chord U&L chord 3
Roof D137 232 Brace 908.3 U&L chord U&L chord 3
Roof D140 233 Brace 908.3 U&L chord U&L chord 3
Roof D141 234 Brace 978.1 U&L chord U&L chord 3
Roof D142 235 Brace 908.3 U&L chord U&L chord 3
Roof D143 236 Brace 908.3 U&L chord U&L chord 3
Roof D144 237 Brace 978.1 U&L chord U&L chord 3
Roof D147 238 Brace 908.3 U&L chord U&L chord 3
Roof D148 239 Brace 908.3 U&L chord U&L chord 3
Roof D151 257 Brace 1374.8 W&P chord W&P chord 3
Roof D152 258 Brace 1307.4 W&P chord W&P chord 3
Roof D153 259 Brace 1307.4 W&P chord W&P chord 3
Roof D155 260 Brace 1307.4 W&P chord W&P chord 3
Roof D156 262 Brace 1307.4 W&P chord W&P chord 3
Roof D157 263 Brace 1374.8 W&P chord W&P chord 3
Roof D159 268 Brace 768.5 U&L chord U&L chord 3
Roof D160 269 Brace 838.4 U&L chord U&L chord 3
Roof D161 271 Brace 838.4 U&L chord U&L chord 3
Roof D164 272 Brace 768.5 U&L chord U&L chord 3
Roof D165 273 Brace 838.4 U&L chord U&L chord 3
Roof D166 274 Brace 838.4 U&L chord U&L chord 3
Roof D199 275 Brace 768.5 U&L chord U&L chord 3
Roof D200 276 Brace 838.4 U&L chord U&L chord 3
Roof D213 277 Brace 838.4 U&L chord U&L chord 3
Roof D214 278 Brace 768.5 U&L chord U&L chord 3
Roof D215 279 Brace 838.4 U&L chord U&L chord 3
Roof D216 280 Brace 838.4 U&L chord U&L chord 3
Roof D219 355 Brace 1173.6 W&P chord W&P chord 3
Roof D220 356 Brace 1240.4 W&P chord W&P chord 3
Roof D221 357 Brace 1240.4 W&P chord W&P chord 3
Roof D222 358 Brace 1173.6 W&P chord W&P chord 3
Roof D223 359 Brace 1240.4 W&P chord W&P chord 3
Roof D225 360 Brace 1240.4 W&P chord W&P chord 3
Roof D227 366 Brace 978.1 U&L chord U&L chord 3
Roof D230 367 Brace 908.3 U&L chord U&L chord 3
Roof D231 368 Brace 908.3 U&L chord U&L chord 3

Page 43 of 80
Assignments 8/31/2018

Table 3.2 - Frame Assignments - Summary (continued)

Max
Min
Unique Design Length Analysis Design Station
Story Label Number
Name Type mm Section Section Spacing
Stations
mm
Roof D232 369 Brace 978.1 U&L chord U&L chord 3
Roof D233 370 Brace 908.3 U&L chord U&L chord 3
Roof D234 371 Brace 908.3 U&L chord U&L chord 3
Roof D236 372 Brace 978.1 U&L chord U&L chord 3
Roof D238 373 Brace 908.3 U&L chord U&L chord 3
Roof D239 374 Brace 908.3 U&L chord U&L chord 3
Roof D241 375 Brace 978.1 U&L chord U&L chord 3
Roof D244 376 Brace 908.3 U&L chord U&L chord 3
Roof D245 377 Brace 908.3 U&L chord U&L chord 3
Roof D253 382 Brace 1374.8 W&P chord W&P chord 3
Roof D254 383 Brace 1307.4 W&P chord W&P chord 3
Roof D257 384 Brace 1307.4 W&P chord W&P chord 3
Roof D258 388 Brace 1307.4 W&P chord W&P chord 3
Roof D259 392 Brace 1307.4 W&P chord W&P chord 3
Roof D264 393 Brace 1374.8 W&P chord W&P chord 3
Roof D265 394 Brace 768.5 U&L chord U&L chord 3
Roof D266 396 Brace 838.4 U&L chord U&L chord 3
Roof D271 397 Brace 838.4 U&L chord U&L chord 3
Roof D272 398 Brace 768.5 U&L chord U&L chord 3
Roof D273 403 Brace 838.4 U&L chord U&L chord 3
Roof D309 406 Brace 838.4 U&L chord U&L chord 3
Roof D311 407 Brace 768.5 U&L chord U&L chord 3
Roof D312 408 Brace 838.4 U&L chord U&L chord 3
Roof D313 409 Brace 838.4 U&L chord U&L chord 3
Roof D314 412 Brace 768.5 U&L chord U&L chord 3
Roof D315 413 Brace 838.4 U&L chord U&L chord 3
Roof D316 414 Brace 838.4 U&L chord U&L chord 3
Roof D317 459 Brace 1173.6 W&P chord W&P chord 3
Roof D318 460 Brace 1240.4 W&P chord W&P chord 3
Roof D319 461 Brace 1240.4 W&P chord W&P chord 3
Roof D320 464 Brace 1173.6 W&P chord W&P chord 3
Roof D321 517 Brace 1240.4 W&P chord W&P chord 3
Roof D322 518 Brace 1240.4 W&P chord W&P chord 3
Roof D323 546 Brace 978.1 U&L chord U&L chord 3
Roof D324 547 Brace 908.3 U&L chord U&L chord 3
Roof D325 548 Brace 908.3 U&L chord U&L chord 3
Roof D326 549 Brace 978.1 U&L chord U&L chord 3
Roof D327 550 Brace 908.3 U&L chord U&L chord 3
Roof D328 551 Brace 908.3 U&L chord U&L chord 3
Roof D329 552 Brace 978.1 U&L chord U&L chord 3
Roof D330 553 Brace 908.3 U&L chord U&L chord 3
Roof D331 554 Brace 908.3 U&L chord U&L chord 3
Roof D332 555 Brace 978.1 U&L chord U&L chord 3
Roof D333 556 Brace 908.3 U&L chord U&L chord 3

Page 44 of 80
Assignments 8/31/2018

Table 3.2 - Frame Assignments - Summary (continued)

Max
Min
Unique Design Length Analysis Design Station
Story Label Number
Name Type mm Section Section Spacing
Stations
mm
Roof D334 557 Brace 908.3 U&L chord U&L chord 3
Roof D335 562 Brace 1374.8 W&P chord W&P chord 3
Roof D336 563 Brace 1307.4 W&P chord W&P chord 3
Roof D337 564 Brace 1307.4 W&P chord W&P chord 3
Roof D338 565 Brace 1307.4 W&P chord W&P chord 3
Roof D339 566 Brace 1307.4 W&P chord W&P chord 3
Roof D340 567 Brace 1374.8 W&P chord W&P chord 3
Roof D341 568 Brace 768.5 U&L chord U&L chord 3
Roof D342 569 Brace 838.4 U&L chord U&L chord 3
Roof D343 570 Brace 838.4 U&L chord U&L chord 3
Roof D344 571 Brace 768.5 U&L chord U&L chord 3
Roof D345 572 Brace 838.4 U&L chord U&L chord 3
Roof D346 573 Brace 838.4 U&L chord U&L chord 3
Roof D347 574 Brace 768.5 U&L chord U&L chord 3
Roof D348 575 Brace 838.4 U&L chord U&L chord 3
Roof D349 576 Brace 838.4 U&L chord U&L chord 3
Roof D350 577 Brace 768.5 U&L chord U&L chord 3
Roof D351 578 Brace 838.4 U&L chord U&L chord 3
Roof D352 579 Brace 838.4 U&L chord U&L chord 3
Roof D353 584 Brace 1173.6 W&P chord W&P chord 3
Roof D354 585 Brace 1240.4 W&P chord W&P chord 3
Roof D355 586 Brace 1240.4 W&P chord W&P chord 3
Roof D356 587 Brace 1173.6 W&P chord W&P chord 3
Roof D357 588 Brace 1240.4 W&P chord W&P chord 3
Roof D358 589 Brace 1240.4 W&P chord W&P chord 3
Story1 D1 63 Brace 971.8 W&P chord W&P chord 3
Story1 D2 64 Brace 971.8 W&P chord W&P chord 3
Story1 D3 66 Brace 971.8 W&P chord W&P chord 3
Story1 D4 76 Brace 971.8 W&P chord W&P chord 3
Story1 D5 77 Brace 971.8 W&P chord W&P chord 3
Story1 D6 79 Brace 971.8 W&P chord W&P chord 3
Story1 D7 87 Brace 971.8 W&P chord W&P chord 3
Story1 D8 88 Brace 971.8 W&P chord W&P chord 3
Story1 D9 90 Brace 971.8 W&P chord W&P chord 3
Story1 D10 100 Brace 971.8 W&P chord W&P chord 3
Story1 D11 101 Brace 971.8 W&P chord W&P chord 3
Story1 D12 103 Brace 971.8 W&P chord W&P chord 3
Story1 D13 113 Brace 971.8 W&P chord W&P chord 3
Story1 D14 114 Brace 971.8 W&P chord W&P chord 3
Story1 D15 116 Brace 971.8 W&P chord W&P chord 3
Story1 D16 124 Brace 971.8 W&P chord W&P chord 3
Story1 D17 125 Brace 971.8 W&P chord W&P chord 3
Story1 D18 127 Brace 971.8 W&P chord W&P chord 3
Story1 D19 140 Brace 1118 W&P chord W&P chord 3

Page 45 of 80
Assignments 8/31/2018

Table 3.2 - Frame Assignments - Summary (continued)

Max
Min
Unique Design Length Analysis Design Station
Story Label Number
Name Type mm Section Section Spacing
Stations
mm
Story1 D20 142 Brace 1118 W&P chord W&P chord 3
Story1 D21 144 Brace 1118 W&P chord W&P chord 3
Story1 D22 152 Brace 1118 W&P chord W&P chord 3
Story1 D23 154 Brace 1118 W&P chord W&P chord 3
Story1 D24 156 Brace 1118 W&P chord W&P chord 3
Story1 D25 164 Brace 1118 W&P chord W&P chord 3
Story1 D26 166 Brace 1118 W&P chord W&P chord 3
Story1 D27 168 Brace 1118 W&P chord W&P chord 3
Story1 D28 176 Brace 1118 W&P chord W&P chord 3
Story1 D29 178 Brace 1118 W&P chord W&P chord 3
Story1 D30 180 Brace 1118 W&P chord W&P chord 3
Story1 D31 187 Brace 1118 W&P chord W&P chord 3
Story1 D32 189 Brace 1118 W&P chord W&P chord 3
Story1 D33 191 Brace 1118 W&P chord W&P chord 3
Story1 D34 199 Brace 1118 W&P chord W&P chord 3
Story1 D35 201 Brace 1118 W&P chord W&P chord 3
Story1 D36 203 Brace 1118 W&P chord W&P chord 3
Story1 D37 211 Brace 1118 W&P chord W&P chord 3
Story1 D38 213 Brace 1118 W&P chord W&P chord 3
Story1 D39 215 Brace 1118 W&P chord W&P chord 3
Story1 D40 223 Brace 1118 W&P chord W&P chord 3
Story1 D41 225 Brace 1118 W&P chord W&P chord 3
Story1 D42 227 Brace 1118 W&P chord W&P chord 3

3.3 Shell Assignments

Table 3.3 - Shell Assignments - Summary

Unique
Story Label Section
Name
GF F1 1 S110
GF F2 2 S110
GF F3 3 S110
GF F4 4 S110
GF F5 5 S110
GF F6 6 S110
GF F7 7 S110
GF F8 8 S110
GF F9 9 S110
GF F10 10 S110
GF F11 11 S110
GF F12 12 S110

Page 46 of 80
Loads 8/31/2018

4 Loads
This chapter provides loading information as applied to the model.
4.1 Load Patterns
Table 4.1 - Load Patterns

Self
Name Type Weight Auto Load
Multiplier
Dead Dead 1
Live Live 0
SDL Superimposed Dead 0
Wind Wind 0 ASCE 7-10

4.2 Auto Wind Loading

Page 47 of 80
Loads 8/31/2018

ASCE 7-10 Auto Wind Load Calculation

This calculation presents the automatically generated lateral wind loads for load pattern Wind according to
ASCE 7-10, as calculated by ETABS.

Exposure Parameters

Exposure From = Shell Objects

Exposure Category = B
Wind Direction = 0 degrees
Top Story = Roof
Bottom Story = Base
Include Parapet = No
Factors and Coefficients

Solid/Gross Area Ratio = 0.2

Gradient Height, z g [ASCE Table 26.9-1] z g = 1200

Emperical Exponent, α [ASCE Table 26.9-1] α=7

2

Velocity Pressure Exposure Coefficient, K z; z α

Kz = 2.01 for 15ft ≤ z ≤ z g

[ASCE Table 27.3-1] zg
2

15 α

Kz = 2.01 for z < 15ft

zg

Topographical Factor, K zt [ASCE 26.8.2] Kzt = 1

Directionality Factor, K d [ASCE 26.6] Kd = 0.85
Gust Effect Factor, G [ASCE 26.9] G = 0.85
Lateral Loading

Velocity Pressure, q z [ASCE 27.3.2 Eq.

q z = 0.00256 Kz Kzt Kd V 2
27.3-1]
Design Wind Pressure, p [ASCE 27.4.2 Eq.
p = qG Cp
27.4-2]

Applied Story Forces

Page 48 of 80
Loads 8/31/2018

Story Elevation X-Dir Y-Dir

m kN kN
Roof 8.16 0 10.0382
Story1 4.5 0 3.625
1F 4 0 0
GF 1 0 0
Base 0 0 0

Page 49 of 80
Loads 8/31/2018

4.3 Applied Loads

4.3.1 Line Loads

Table 4.3 - Frame Loads - Distributed

Absolute Absolute
Relative Relative Force Force
Unique Design Load Distance Distance
Story Label LoadType Direction Distance Distance at Start at End
Name Type Pattern Start End
Start End kN/m kN/m
mm mm
Gravity
GF B1 16 Beam SDL Force 0 1 0 3000 9 9
Proj
Gravity
GF B2 17 Beam SDL Force 0 1 0 3000 9 9
Proj
Gravity
GF B3 18 Beam SDL Force 0 1 0 3000 9 9
Proj
Gravity
GF B4 19 Beam SDL Force 0 1 0 3000 9 9
Proj
Gravity
GF B13 28 Beam SDL Force 0 1 0 2500 9 9
Proj
Gravity
GF B14 29 Beam SDL Force 0 1 0 2500 9 9
Proj
Gravity
GF B15 30 Beam SDL Force 0 1 0 2500 9 9
Proj
Gravity
GF B16 31 Beam SDL Force 0 1 0 3000 9 9
Proj
Gravity
GF B17 32 Beam SDL Force 0 1 0 3000 9 9
Proj
Gravity
GF B18 33 Beam SDL Force 0 1 0 3000 9 9
Proj
Gravity
GF B19 34 Beam SDL Force 0 1 0 3000 9 9
Proj
Gravity
GF B20 35 Beam SDL Force 0 1 0 2500 9 9
Proj
Gravity
GF B21 36 Beam SDL Force 0 1 0 2500 9 9
Proj
Gravity
GF B22 37 Beam SDL Force 0 1 0 2500 9 9
Proj
Gravity
Roof D121 646 Brace Live Force 0 1 0 1397.3 0.3 0.3
Proj
Gravity
Roof D122 647 Brace Live Force 0 1 0 1397.3 0.3 0.3
Proj
Gravity
Roof D125 650 Brace Live Force 0 1 0 1397.3 0.3 0.3
Proj
Gravity
Roof D126 651 Brace Live Force 0 1 0 1397.3 0.3 0.3
Proj
Gravity
Roof D145 386 Brace Live Force 0 1 0 1397.3 0.3 0.3
Proj
Gravity
Roof D146 387 Brace Live Force 0 1 0 1397.3 0.3 0.3
Proj
Gravity
Roof D149 390 Brace Live Force 0 1 0 1397.3 0.3 0.3
Proj

Page 50 of 80
Loads 8/31/2018

Table 4.3 - Frame Loads - Distributed (continued)

Absolute Absolute
Relative Relative Force Force
Unique Design Load Distance Distance
Story Label LoadType Direction Distance Distance at Start at End
Name Type Pattern Start End
Start End kN/m kN/m
mm mm
Gravity
Roof D150 391 Brace Live Force 0 1 0 1397.3 0.3 0.3
Proj
Gravity
Roof D175 449 Brace Live Force 0 1 0 5240 0.3 0.3
Proj
Gravity
Roof D176 450 Brace Live Force 0 1 0 5240 0.3 0.3
Proj
Gravity
Roof D177 451 Brace Live Force 0 1 0 5240 0.3 0.3
Proj
Gravity
Roof D178 452 Brace Live Force 0 1 0 5240 0.3 0.3
Proj
Gravity
Roof D179 453 Brace Live Force 0 1 0 5240 0.3 0.3
Proj
Gravity
Roof D180 454 Brace Live Force 0 1 0 5240 0.3 0.3
Proj
Gravity
Roof D181 455 Brace Live Force 0 1 0 5240 0.3 0.3
Proj
Gravity
Roof D182 456 Brace Live Force 0 1 0 5240 0.3 0.3
Proj
Gravity
Roof D217 602 Brace Live Force 0 1 0 2630.1 0.3 0.3
Proj
Gravity
Roof D218 603 Brace Live Force 0 1 0 2630.1 0.3 0.3
Proj
Gravity
Roof D224 609 Brace Live Force 0 1 0 2504.8 0.3 0.3
Proj
Gravity
Roof D226 611 Brace Live Force 0 1 0 1252.4 0.3 0.3
Proj
Gravity
Roof D228 613 Brace Live Force 0 1 0 2630.1 0.3 0.3
Proj
Gravity
Roof D229 614 Brace Live Force 0 1 0 2630.1 0.3 0.3
Proj
Gravity
Roof D235 620 Brace Live Force 0 1 0 2504.8 0.3 0.3
Proj
Gravity
Roof D237 622 Brace Live Force 0 1 0 1252.4 0.3 0.3
Proj
Gravity
Roof D240 624 Brace Live Force 0 1 0 1165.4 0.3 0.3
Proj
Gravity
Roof D246 629 Brace Live Force 0 1 0 1165.4 0.3 0.3
Proj
Gravity
Roof D255 701 Brace Live Force 0 1 0 2630.1 0.3 0.3
Proj
Gravity
Roof D256 702 Brace Live Force 0 1 0 2630.1 0.3 0.3
Proj
Gravity
Roof D260 706 Brace Live Force 0 1 0 2504.8 0.3 0.3
Proj

Page 51 of 80
Loads 8/31/2018

Table 4.3 - Frame Loads - Distributed (continued)

Absolute Absolute
Relative Relative Force Force
Unique Design Load Distance Distance
Story Label LoadType Direction Distance Distance at Start at End
Name Type Pattern Start End
Start End kN/m kN/m
mm mm
Gravity
Roof D261 707 Brace Live Force 0 1 0 1252.4 0.3 0.3
Proj
Gravity
Roof D262 708 Brace Live Force 0 1 0 2630.1 0.3 0.3
Proj
Gravity
Roof D263 709 Brace Live Force 0 1 0 2630.1 0.3 0.3
Proj
Gravity
Roof D267 713 Brace Live Force 0 1 0 2504.8 0.3 0.3
Proj
Gravity
Roof D268 714 Brace Live Force 0 1 0 1252.4 0.3 0.3
Proj
Gravity
Roof D269 715 Brace Live Force 0 1 0 1165.4 0.3 0.3
Proj
Gravity
Roof D270 716 Brace Live Force 0 1 0 1165.4 0.3 0.3
Proj
Gravity
Roof D274 719 Brace Live Force 0 1 0 1053 0.3 0.3
Proj
Gravity
Roof D275 720 Brace Live Force 0 1 0 1053 0.3 0.3
Proj
Gravity
Roof D276 721 Brace Live Force 0 1 0 1053 0.3 0.3
Proj
Gravity
Roof D283 730 Brace Live Force 0 1 0 1053 0.3 0.3
Proj
Gravity
Roof D284 731 Brace Live Force 0 1 0 1053 0.3 0.3
Proj
Gravity
Roof D285 732 Brace Live Force 0 1 0 1053 0.3 0.3
Proj
Gravity
Roof D292 741 Brace Live Force 0 1 0 1053 0.3 0.3
Proj
Gravity
Roof D293 742 Brace Live Force 0 1 0 1053 0.3 0.3
Proj
Gravity
Roof D294 743 Brace Live Force 0 1 0 1053 0.3 0.3
Proj
Gravity
Roof D301 752 Brace Live Force 0 1 0 1053 0.3 0.3
Proj
Gravity
Roof D302 753 Brace Live Force 0 1 0 1053 0.3 0.3
Proj
Gravity
Roof D303 754 Brace Live Force 0 1 0 1053 0.3 0.3
Proj
Gravity
Roof D43 389 Brace Live Force 0 1 0 2445.4 0.3 0.3
Proj
Gravity
Roof D44 385 Brace Live Force 0 1 0 2445.4 0.3 0.3
Proj
Gravity
Roof D45 645 Brace Live Force 0 1 0 2445.4 0.3 0.3
Proj

Page 52 of 80
Loads 8/31/2018

Table 4.3 - Frame Loads - Distributed (continued)

Absolute Absolute
Relative Relative Force Force
Unique Design Load Distance Distance
Story Label LoadType Direction Distance Distance at Start at End
Name Type Pattern Start End
Start End kN/m kN/m
mm mm
Gravity
Roof D46 649 Brace Live Force 0 1 0 2445.4 0.3 0.3
Proj
Gravity
Roof D132 228 Brace Live Force 0 1 0 978.1 0.3 0.3
Proj
Gravity
Roof D133 229 Brace Live Force 0 1 0 908.3 0.3 0.3
Proj
Gravity
Roof D135 230 Brace Live Force 0 1 0 908.3 0.3 0.3
Proj
Gravity
Roof D136 231 Brace Live Force 0 1 0 978.1 0.3 0.3
Proj
Gravity
Roof D137 232 Brace Live Force 0 1 0 908.3 0.3 0.3
Proj
Gravity
Roof D140 233 Brace Live Force 0 1 0 908.3 0.3 0.3
Proj
Gravity
Roof D159 268 Brace Live Force 0 1 0 768.5 0.3 0.3
Proj
Gravity
Roof D160 269 Brace Live Force 0 1 0 838.4 0.3 0.3
Proj
Gravity
Roof D161 271 Brace Live Force 0 1 0 838.4 0.3 0.3
Proj
Gravity
Roof D164 272 Brace Live Force 0 1 0 768.5 0.3 0.3
Proj
Gravity
Roof D165 273 Brace Live Force 0 1 0 838.4 0.3 0.3
Proj
Gravity
Roof D166 274 Brace Live Force 0 1 0 838.4 0.3 0.3
Proj
Gravity
Roof D227 366 Brace Live Force 0 1 0 978.1 0.3 0.3
Proj
Gravity
Roof D230 367 Brace Live Force 0 1 0 908.3 0.3 0.3
Proj
Gravity
Roof D231 368 Brace Live Force 0 1 0 908.3 0.3 0.3
Proj
Gravity
Roof D232 369 Brace Live Force 0 1 0 978.1 0.3 0.3
Proj
Gravity
Roof D233 370 Brace Live Force 0 1 0 908.3 0.3 0.3
Proj
Gravity
Roof D234 371 Brace Live Force 0 1 0 908.3 0.3 0.3
Proj
Gravity
Roof D265 394 Brace Live Force 0 1 0 768.5 0.3 0.3
Proj
Gravity
Roof D266 396 Brace Live Force 0 1 0 838.4 0.3 0.3
Proj
Gravity
Roof D271 397 Brace Live Force 0 1 0 838.4 0.3 0.3
Proj

Page 53 of 80
Loads 8/31/2018

Table 4.3 - Frame Loads - Distributed (continued)

Absolute Absolute
Relative Relative Force Force
Unique Design Load Distance Distance
Story Label LoadType Direction Distance Distance at Start at End
Name Type Pattern Start End
Start End kN/m kN/m
mm mm
Gravity
Roof D272 398 Brace Live Force 0 1 0 768.5 0.3 0.3
Proj
Gravity
Roof D273 403 Brace Live Force 0 1 0 838.4 0.3 0.3
Proj
Gravity
Roof D309 406 Brace Live Force 0 1 0 838.4 0.3 0.3
Proj
Gravity
Roof D323 546 Brace Live Force 0 1 0 978.1 0.3 0.3
Proj
Gravity
Roof D324 547 Brace Live Force 0 1 0 908.3 0.3 0.3
Proj
Gravity
Roof D325 548 Brace Live Force 0 1 0 908.3 0.3 0.3
Proj
Gravity
Roof D326 549 Brace Live Force 0 1 0 978.1 0.3 0.3
Proj
Gravity
Roof D327 550 Brace Live Force 0 1 0 908.3 0.3 0.3
Proj
Gravity
Roof D328 551 Brace Live Force 0 1 0 908.3 0.3 0.3
Proj
Gravity
Roof D341 568 Brace Live Force 0 1 0 768.5 0.3 0.3
Proj
Gravity
Roof D342 569 Brace Live Force 0 1 0 838.4 0.3 0.3
Proj
Gravity
Roof D343 570 Brace Live Force 0 1 0 838.4 0.3 0.3
Proj
Gravity
Roof D344 571 Brace Live Force 0 1 0 768.5 0.3 0.3
Proj
Gravity
Roof D345 572 Brace Live Force 0 1 0 838.4 0.3 0.3
Proj
Gravity
Roof D346 573 Brace Live Force 0 1 0 838.4 0.3 0.3
Proj
Roof D121 646 Brace SDL Force Gravity 0 1 0 1397.3 0.45 0.45
Gravity
Roof D121 646 Brace SDL Force 0 1 0 1397.3 0.4 0.4
Proj
Roof D122 647 Brace SDL Force Gravity 0 1 0 1397.3 0.45 0.45
Gravity
Roof D122 647 Brace SDL Force 0 1 0 1397.3 0.4 0.4
Proj
Roof D125 650 Brace SDL Force Gravity 0 1 0 1397.3 0.45 0.45
Gravity
Roof D125 650 Brace SDL Force 0 1 0 1397.3 0.4 0.4
Proj
Roof D126 651 Brace SDL Force Gravity 0 1 0 1397.3 0.45 0.45
Gravity
Roof D126 651 Brace SDL Force 0 1 0 1397.3 0.4 0.4
Proj
Roof D145 386 Brace SDL Force Gravity 0 1 0 1397.3 0.45 0.45
Gravity
Roof D145 386 Brace SDL Force 0 1 0 1397.3 0.4 0.4
Proj

Page 54 of 80
Loads 8/31/2018

Table 4.3 - Frame Loads - Distributed (continued)

Absolute Absolute
Relative Relative Force Force
Unique Design Load Distance Distance
Story Label LoadType Direction Distance Distance at Start at End
Name Type Pattern Start End
Start End kN/m kN/m
mm mm
Roof D146 387 Brace SDL Force Gravity 0 1 0 1397.3 0.45 0.45
Gravity
Roof D146 387 Brace SDL Force 0 1 0 1397.3 0.4 0.4
Proj
Roof D149 390 Brace SDL Force Gravity 0 1 0 1397.3 0.45 0.45
Gravity
Roof D149 390 Brace SDL Force 0 1 0 1397.3 0.4 0.4
Proj
Roof D150 391 Brace SDL Force Gravity 0 1 0 1397.3 0.45 0.45
Gravity
Roof D150 391 Brace SDL Force 0 1 0 1397.3 0.4 0.4
Proj
Roof D175 449 Brace SDL Force Gravity 0 1 0 5240 0.45 0.45
Gravity
Roof D175 449 Brace SDL Force 0 1 0 5240 0.4 0.4
Proj
Roof D176 450 Brace SDL Force Gravity 0 1 0 5240 0.45 0.45
Gravity
Roof D176 450 Brace SDL Force 0 1 0 5240 0.4 0.4
Proj
Roof D177 451 Brace SDL Force Gravity 0 1 0 5240 0.45 0.45
Gravity
Roof D177 451 Brace SDL Force 0 1 0 5240 0.4 0.4
Proj
Roof D178 452 Brace SDL Force Gravity 0 1 0 5240 0.45 0.45
Gravity
Roof D178 452 Brace SDL Force 0 1 0 5240 0.4 0.4
Proj
Roof D179 453 Brace SDL Force Gravity 0 1 0 5240 0.45 0.45
Gravity
Roof D179 453 Brace SDL Force 0 1 0 5240 0.4 0.4
Proj
Roof D180 454 Brace SDL Force Gravity 0 1 0 5240 0.45 0.45
Gravity
Roof D180 454 Brace SDL Force 0 1 0 5240 0.4 0.4
Proj
Roof D181 455 Brace SDL Force Gravity 0 1 0 5240 0.45 0.45
Gravity
Roof D181 455 Brace SDL Force 0 1 0 5240 0.4 0.4
Proj
Roof D182 456 Brace SDL Force Gravity 0 1 0 5240 0.45 0.45
Gravity
Roof D182 456 Brace SDL Force 0 1 0 5240 0.4 0.4
Proj
Roof D217 602 Brace SDL Force Gravity 0 1 0 2630.1 0.45 0.45
Gravity
Roof D217 602 Brace SDL Force 0 1 0 2630.1 0.4 0.4
Proj
Roof D218 603 Brace SDL Force Gravity 0 1 0 2630.1 0.45 0.45
Gravity
Roof D218 603 Brace SDL Force 0 1 0 2630.1 0.4 0.4
Proj
Roof D224 609 Brace SDL Force Gravity 0 1 0 2504.8 0.45 0.45
Gravity
Roof D224 609 Brace SDL Force 0 1 0 2504.8 0.4 0.4
Proj
Roof D226 611 Brace SDL Force Gravity 0 1 0 1252.4 0.45 0.45
Gravity
Roof D226 611 Brace SDL Force 0 1 0 1252.4 0.4 0.4
Proj

Page 55 of 80
Loads 8/31/2018

Table 4.3 - Frame Loads - Distributed (continued)

Absolute Absolute
Relative Relative Force Force
Unique Design Load Distance Distance
Story Label LoadType Direction Distance Distance at Start at End
Name Type Pattern Start End
Start End kN/m kN/m
mm mm
Roof D228 613 Brace SDL Force Gravity 0 1 0 2630.1 0.45 0.45
Gravity
Roof D228 613 Brace SDL Force 0 1 0 2630.1 0.4 0.4
Proj
Roof D229 614 Brace SDL Force Gravity 0 1 0 2630.1 0.45 0.45
Gravity
Roof D229 614 Brace SDL Force 0 1 0 2630.1 0.4 0.4
Proj
Roof D235 620 Brace SDL Force Gravity 0 1 0 2504.8 0.45 0.45
Gravity
Roof D235 620 Brace SDL Force 0 1 0 2504.8 0.4 0.4
Proj
Roof D237 622 Brace SDL Force Gravity 0 1 0 1252.4 0.45 0.45
Gravity
Roof D237 622 Brace SDL Force 0 1 0 1252.4 0.4 0.4
Proj
Roof D240 624 Brace SDL Force Gravity 0 1 0 1165.4 0.45 0.45
Gravity
Roof D240 624 Brace SDL Force 0 1 0 1165.4 0.4 0.4
Proj
Roof D246 629 Brace SDL Force Gravity 0 1 0 1165.4 0.45 0.45
Gravity
Roof D246 629 Brace SDL Force 0 1 0 1165.4 0.4 0.4
Proj
Roof D255 701 Brace SDL Force Gravity 0 1 0 2630.1 0.45 0.45
Gravity
Roof D255 701 Brace SDL Force 0 1 0 2630.1 0.4 0.4
Proj
Roof D256 702 Brace SDL Force Gravity 0 1 0 2630.1 0.45 0.45
Gravity
Roof D256 702 Brace SDL Force 0 1 0 2630.1 0.4 0.4
Proj
Roof D260 706 Brace SDL Force Gravity 0 1 0 2504.8 0.45 0.45
Gravity
Roof D260 706 Brace SDL Force 0 1 0 2504.8 0.4 0.4
Proj
Roof D261 707 Brace SDL Force Gravity 0 1 0 1252.4 0.45 0.45
Gravity
Roof D261 707 Brace SDL Force 0 1 0 1252.4 0.4 0.4
Proj
Roof D262 708 Brace SDL Force Gravity 0 1 0 2630.1 0.45 0.45
Gravity
Roof D262 708 Brace SDL Force 0 1 0 2630.1 0.4 0.4
Proj
Roof D263 709 Brace SDL Force Gravity 0 1 0 2630.1 0.45 0.45
Gravity
Roof D263 709 Brace SDL Force 0 1 0 2630.1 0.4 0.4
Proj
Roof D267 713 Brace SDL Force Gravity 0 1 0 2504.8 0.45 0.45
Gravity
Roof D267 713 Brace SDL Force 0 1 0 2504.8 0.4 0.4
Proj
Roof D268 714 Brace SDL Force Gravity 0 1 0 1252.4 0.45 0.45
Gravity
Roof D268 714 Brace SDL Force 0 1 0 1252.4 0.4 0.4
Proj
Roof D269 715 Brace SDL Force Gravity 0 1 0 1165.4 0.45 0.45
Gravity
Roof D269 715 Brace SDL Force 0 1 0 1165.4 0.4 0.4
Proj

Page 56 of 80
Loads 8/31/2018

Table 4.3 - Frame Loads - Distributed (continued)

Absolute Absolute
Relative Relative Force Force
Unique Design Load Distance Distance
Story Label LoadType Direction Distance Distance at Start at End
Name Type Pattern Start End
Start End kN/m kN/m
mm mm
Roof D270 716 Brace SDL Force Gravity 0 1 0 1165.4 0.45 0.45
Gravity
Roof D270 716 Brace SDL Force 0 1 0 1165.4 0.4 0.4
Proj
Roof D274 719 Brace SDL Force Gravity 0 1 0 1053 0.45 0.45
Gravity
Roof D274 719 Brace SDL Force 0 1 0 1053 0.4 0.4
Proj
Roof D275 720 Brace SDL Force Gravity 0 1 0 1053 0.45 0.45
Gravity
Roof D275 720 Brace SDL Force 0 1 0 1053 0.4 0.4
Proj
Roof D276 721 Brace SDL Force Gravity 0 1 0 1053 0.45 0.45
Gravity
Roof D276 721 Brace SDL Force 0 1 0 1053 0.4 0.4
Proj
Roof D283 730 Brace SDL Force Gravity 0 1 0 1053 0.45 0.45
Gravity
Roof D283 730 Brace SDL Force 0 1 0 1053 0.4 0.4
Proj
Roof D284 731 Brace SDL Force Gravity 0 1 0 1053 0.45 0.45
Gravity
Roof D284 731 Brace SDL Force 0 1 0 1053 0.4 0.4
Proj
Roof D285 732 Brace SDL Force Gravity 0 1 0 1053 0.45 0.45
Gravity
Roof D285 732 Brace SDL Force 0 1 0 1053 0.4 0.4
Proj
Roof D292 741 Brace SDL Force Gravity 0 1 0 1053 0.45 0.45
Gravity
Roof D292 741 Brace SDL Force 0 1 0 1053 0.4 0.4
Proj
Roof D293 742 Brace SDL Force Gravity 0 1 0 1053 0.45 0.45
Gravity
Roof D293 742 Brace SDL Force 0 1 0 1053 0.4 0.4
Proj
Roof D294 743 Brace SDL Force Gravity 0 1 0 1053 0.45 0.45
Gravity
Roof D294 743 Brace SDL Force 0 1 0 1053 0.4 0.4
Proj
Roof D301 752 Brace SDL Force Gravity 0 1 0 1053 0.45 0.45
Gravity
Roof D301 752 Brace SDL Force 0 1 0 1053 0.4 0.4
Proj
Roof D302 753 Brace SDL Force Gravity 0 1 0 1053 0.45 0.45
Gravity
Roof D302 753 Brace SDL Force 0 1 0 1053 0.4 0.4
Proj
Roof D303 754 Brace SDL Force Gravity 0 1 0 1053 0.45 0.45
Gravity
Roof D303 754 Brace SDL Force 0 1 0 1053 0.4 0.4
Proj
Roof D43 389 Brace SDL Force Gravity 0 1 0 2445.4 0.45 0.45
Gravity
Roof D43 389 Brace SDL Force 0 1 0 2445.4 0.4 0.4
Proj
Roof D44 385 Brace SDL Force Gravity 0 1 0 2445.4 0.45 0.45
Gravity
Roof D44 385 Brace SDL Force 0 1 0 2445.4 0.4 0.4
Proj

Page 57 of 80
Loads 8/31/2018

Table 4.3 - Frame Loads - Distributed (continued)

Absolute Absolute
Relative Relative Force Force
Unique Design Load Distance Distance
Story Label LoadType Direction Distance Distance at Start at End
Name Type Pattern Start End
Start End kN/m kN/m
mm mm
Roof D45 645 Brace SDL Force Gravity 0 1 0 2445.4 0.45 0.45
Gravity
Roof D45 645 Brace SDL Force 0 1 0 2445.4 0.4 0.4
Proj
Roof D46 649 Brace SDL Force Gravity 0 1 0 2445.4 0.45 0.45
Gravity
Roof D46 649 Brace SDL Force 0 1 0 2445.4 0.4 0.4
Proj
Roof D132 228 Brace SDL Force Gravity 0 1 0 978.1 0.45 0.45
Gravity
Roof D132 228 Brace SDL Force 0 1 0 978.1 0.4 0.4
Proj
Roof D133 229 Brace SDL Force Gravity 0 1 0 908.3 0.45 0.45
Gravity
Roof D133 229 Brace SDL Force 0 1 0 908.3 0.4 0.4
Proj
Roof D135 230 Brace SDL Force Gravity 0 1 0 908.3 0.45 0.45
Gravity
Roof D135 230 Brace SDL Force 0 1 0 908.3 0.4 0.4
Proj
Roof D136 231 Brace SDL Force Gravity 0 1 0 978.1 0.45 0.45
Gravity
Roof D136 231 Brace SDL Force 0 1 0 978.1 0.4 0.4
Proj
Roof D137 232 Brace SDL Force Gravity 0 1 0 908.3 0.45 0.45
Gravity
Roof D137 232 Brace SDL Force 0 1 0 908.3 0.4 0.4
Proj
Roof D140 233 Brace SDL Force Gravity 0 1 0 908.3 0.45 0.45
Gravity
Roof D140 233 Brace SDL Force 0 1 0 908.3 0.4 0.4
Proj
Roof D159 268 Brace SDL Force Gravity 0 1 0 768.5 0.45 0.45
Gravity
Roof D159 268 Brace SDL Force 0 1 0 768.5 0.4 0.4
Proj
Roof D160 269 Brace SDL Force Gravity 0 1 0 838.4 0.45 0.45
Gravity
Roof D160 269 Brace SDL Force 0 1 0 838.4 0.4 0.4
Proj
Roof D161 271 Brace SDL Force Gravity 0 1 0 838.4 0.45 0.45
Gravity
Roof D161 271 Brace SDL Force 0 1 0 838.4 0.4 0.4
Proj
Roof D164 272 Brace SDL Force Gravity 0 1 0 768.5 0.45 0.45
Gravity
Roof D164 272 Brace SDL Force 0 1 0 768.5 0.4 0.4
Proj
Roof D165 273 Brace SDL Force Gravity 0 1 0 838.4 0.45 0.45
Gravity
Roof D165 273 Brace SDL Force 0 1 0 838.4 0.4 0.4
Proj
Roof D166 274 Brace SDL Force Gravity 0 1 0 838.4 0.45 0.45
Gravity
Roof D166 274 Brace SDL Force 0 1 0 838.4 0.4 0.4
Proj
Roof D227 366 Brace SDL Force Gravity 0 1 0 978.1 0.45 0.45
Gravity
Roof D227 366 Brace SDL Force 0 1 0 978.1 0.4 0.4
Proj

Page 58 of 80
Loads 8/31/2018

Table 4.3 - Frame Loads - Distributed (continued)

Absolute Absolute
Relative Relative Force Force
Unique Design Load Distance Distance
Story Label LoadType Direction Distance Distance at Start at End
Name Type Pattern Start End
Start End kN/m kN/m
mm mm
Roof D230 367 Brace SDL Force Gravity 0 1 0 908.3 0.45 0.45
Gravity
Roof D230 367 Brace SDL Force 0 1 0 908.3 0.4 0.4
Proj
Roof D231 368 Brace SDL Force Gravity 0 1 0 908.3 0.45 0.45
Gravity
Roof D231 368 Brace SDL Force 0 1 0 908.3 0.4 0.4
Proj
Roof D232 369 Brace SDL Force Gravity 0 1 0 978.1 0.45 0.45
Gravity
Roof D232 369 Brace SDL Force 0 1 0 978.1 0.4 0.4
Proj
Roof D233 370 Brace SDL Force Gravity 0 1 0 908.3 0.45 0.45
Gravity
Roof D233 370 Brace SDL Force 0 1 0 908.3 0.4 0.4
Proj
Roof D234 371 Brace SDL Force Gravity 0 1 0 908.3 0.45 0.45
Gravity
Roof D234 371 Brace SDL Force 0 1 0 908.3 0.4 0.4
Proj
Roof D265 394 Brace SDL Force Gravity 0 1 0 768.5 0.45 0.45
Gravity
Roof D265 394 Brace SDL Force 0 1 0 768.5 0.4 0.4
Proj
Roof D266 396 Brace SDL Force Gravity 0 1 0 838.4 0.45 0.45
Gravity
Roof D266 396 Brace SDL Force 0 1 0 838.4 0.4 0.4
Proj
Roof D271 397 Brace SDL Force Gravity 0 1 0 838.4 0.45 0.45
Gravity
Roof D271 397 Brace SDL Force 0 1 0 838.4 0.4 0.4
Proj
Roof D272 398 Brace SDL Force Gravity 0 1 0 768.5 0.45 0.45
Gravity
Roof D272 398 Brace SDL Force 0 1 0 768.5 0.4 0.4
Proj
Roof D273 403 Brace SDL Force Gravity 0 1 0 838.4 0.45 0.45
Gravity
Roof D273 403 Brace SDL Force 0 1 0 838.4 0.4 0.4
Proj
Roof D309 406 Brace SDL Force Gravity 0 1 0 838.4 0.45 0.45
Gravity
Roof D309 406 Brace SDL Force 0 1 0 838.4 0.4 0.4
Proj
Roof D323 546 Brace SDL Force Gravity 0 1 0 978.1 0.45 0.45
Gravity
Roof D323 546 Brace SDL Force 0 1 0 978.1 0.4 0.4
Proj
Roof D324 547 Brace SDL Force Gravity 0 1 0 908.3 0.45 0.45
Gravity
Roof D324 547 Brace SDL Force 0 1 0 908.3 0.4 0.4
Proj
Roof D325 548 Brace SDL Force Gravity 0 1 0 908.3 0.45 0.45
Gravity
Roof D325 548 Brace SDL Force 0 1 0 908.3 0.4 0.4
Proj
Roof D326 549 Brace SDL Force Gravity 0 1 0 978.1 0.45 0.45
Gravity
Roof D326 549 Brace SDL Force 0 1 0 978.1 0.4 0.4
Proj

Page 59 of 80
Loads 8/31/2018

Table 4.3 - Frame Loads - Distributed (continued)

Absolute Absolute
Relative Relative Force Force
Unique Design Load Distance Distance
Story Label LoadType Direction Distance Distance at Start at End
Name Type Pattern Start End
Start End kN/m kN/m
mm mm
Roof D327 550 Brace SDL Force Gravity 0 1 0 908.3 0.45 0.45
Gravity
Roof D327 550 Brace SDL Force 0 1 0 908.3 0.4 0.4
Proj
Roof D328 551 Brace SDL Force Gravity 0 1 0 908.3 0.45 0.45
Gravity
Roof D328 551 Brace SDL Force 0 1 0 908.3 0.4 0.4
Proj
Roof D341 568 Brace SDL Force Gravity 0 1 0 768.5 0.45 0.45
Gravity
Roof D341 568 Brace SDL Force 0 1 0 768.5 0.4 0.4
Proj
Roof D342 569 Brace SDL Force Gravity 0 1 0 838.4 0.45 0.45
Gravity
Roof D342 569 Brace SDL Force 0 1 0 838.4 0.4 0.4
Proj
Roof D343 570 Brace SDL Force Gravity 0 1 0 838.4 0.45 0.45
Gravity
Roof D343 570 Brace SDL Force 0 1 0 838.4 0.4 0.4
Proj
Roof D344 571 Brace SDL Force Gravity 0 1 0 768.5 0.45 0.45
Gravity
Roof D344 571 Brace SDL Force 0 1 0 768.5 0.4 0.4
Proj
Roof D345 572 Brace SDL Force Gravity 0 1 0 838.4 0.45 0.45
Gravity
Roof D345 572 Brace SDL Force 0 1 0 838.4 0.4 0.4
Proj
Roof D346 573 Brace SDL Force Gravity 0 1 0 838.4 0.45 0.45
Gravity
Roof D346 573 Brace SDL Force 0 1 0 838.4 0.4 0.4
Proj

4.3.2 Area Loads

Table 4.4 - Shell Loads - Uniform

Unique Load Load

Story Label Direction
Name Pattern kN/m²
GF F1 1 Live Gravity 4.79
GF F2 2 Live Gravity 4.79
GF F3 3 Live Gravity 4.79
GF F4 4 Live Gravity 4.79
GF F5 5 Live Gravity 4.79
GF F6 6 Live Gravity 4.79
GF F7 7 Live Gravity 4.79
GF F8 8 Live Gravity 4.79
GF F9 9 Live Gravity 4.79
GF F10 10 Live Gravity 4.79
GF F11 11 Live Gravity 4.79
GF F12 12 Live Gravity 4.79
GF F1 1 SDL Gravity 1.5
GF F2 2 SDL Gravity 1.5
GF F3 3 SDL Gravity 1.5

Page 60 of 80
Loads 8/31/2018

Table 4.4 - Shell Loads - Uniform (continued)

Unique Load Load

Story Label Direction
Name Pattern kN/m²
GF F4 4 SDL Gravity 1.5
GF F5 5 SDL Gravity 1.5
GF F6 6 SDL Gravity 1.5
GF F7 7 SDL Gravity 1.5
GF F8 8 SDL Gravity 1.5
GF F9 9 SDL Gravity 1.5
GF F10 10 SDL Gravity 1.5
GF F11 11 SDL Gravity 1.5
GF F12 12 SDL Gravity 1.5

4.4 Load Cases

Table 4.5 - Load Cases - Summary

Name Type
Dead Linear Static
Live Linear Static
SDL Linear Static
Wind Linear Static

4.5 Load Combinations

Table 4.6 - Load Combinations

Load Scale
Name Type Auto
Case/Combo Factor
SLS Dead 1 Linear Add No
SLS Live 1 No
SLS SDL 1 No
SLS Wind 1 No
Total DL Dead 1 Linear Add No
Total DL SDL 1 No
DStlS1 Dead 1.4 Linear Add Yes
DStlS1 SDL 1.4 No
DStlS2 Dead 1.2 Linear Add Yes
DStlS2 Live 1.6 No
DStlS2 SDL 1.2 No
DStlS3 Dead 1.2 Linear Add Yes
DStlS3 Live 1 No
DStlS3 SDL 1.2 No
DStlS3 Wind 1 No
DStlS4 Dead 1.2 Linear Add Yes
DStlS4 Live 1 No
DStlS4 SDL 1.2 No
DStlS4 Wind -1 No
DStlS5 Dead 0.9 Linear Add Yes
DStlS5 SDL 0.9 No
DStlS5 Wind 1 No

Page 61 of 80
Loads 8/31/2018

Table 4.6 - Load Combinations (continued)

Load Scale
Name Type Auto
Case/Combo Factor
DStlS6 Dead 0.9 Linear Add Yes
DStlS6 SDL 0.9 No
DStlS6 Wind -1 No
DStlD1 Dead 1 Linear Add Yes
DStlD1 SDL 1 No
DStlD2 Dead 1 Linear Add Yes
DStlD2 Live 1 No
DStlD2 SDL 1 No
DCon1 Dead 1.4 Linear Add Yes
DCon1 SDL 1.4 No
DCon2 Dead 1.2 Linear Add Yes
DCon2 Live 1.6 No
DCon2 SDL 1.2 No
DCon3 Dead 1.2 Linear Add Yes
DCon3 Live 1 No
DCon3 SDL 1.2 No
DCon3 Wind 1 No
DCon4 Dead 1.2 Linear Add Yes
DCon4 Live 1 No
DCon4 SDL 1.2 No
DCon4 Wind -1 No
DCon5 Dead 0.9 Linear Add Yes
DCon5 SDL 0.9 No
DCon5 Wind 1 No
DCon6 Dead 0.9 Linear Add Yes
DCon6 SDL 0.9 No
DCon6 Wind -1 No

Page 62 of 80
Analysis Results 8/31/2018

5 Analysis Results
This chapter provides analysis results.
5.1 Structure Results
Table 5.1 - Base Reactions

Load FX FY FZ MX MY MZ X Y Z
Case/Combo kN kN kN kN-m kN-m kN-m m m m
Dead 0 0 543.2194 2036.9996 -3259.3165 0 0 0 0
Live 0 0 463.7692 1739.1347 -2782.6155 0 0 0 0
SDL 0 0 596.0188 2235.0704 -3576.1126 0 0 0 0
Wind 0 -13.6633 -2.7569 47.5135 16.5417 -81.9797 0 0 0
SLS 0 -13.6633 1600.2505 6058.7182 -9601.503 -81.9797 0 0 0
Total DL 0 0 1139.2382 4272.07 -6835.4292 0 0 0 0
DStlS1 0 0 1594.9335 5980.898 -9569.6009 0 0 0 0
DStlS2 0 0 2109.1166 7909.0995 -12654.6998 0 0 0 0
DStlS3 0 -13.6633 1828.0981 6913.1323 -10968.5889 -81.9797 0 0 0
DStlS4 0 13.6633 1833.612 6818.1052 -11001.6722 81.9797 0 0 0
DStlS5 0 -13.6633 1022.5574 3892.3766 -6135.3446 -81.9797 0 0 0
DStlS6 0 13.6633 1028.0713 3797.3495 -6168.4279 81.9797 0 0 0
DStlD1 0 0 1139.2382 4272.07 -6835.4292 0 0 0 0
DStlD2 0 0 1603.0074 6011.2047 -9618.0447 0 0 0 0
DCon1 0 0 1594.9335 5980.898 -9569.6009 0 0 0 0
DCon2 0 0 2109.1166 7909.0995 -12654.6998 0 0 0 0
DCon3 0 -13.6633 1828.0981 6913.1323 -10968.5889 -81.9797 0 0 0
DCon4 0 13.6633 1833.612 6818.1052 -11001.6722 81.9797 0 0 0
DCon5 0 -13.6633 1022.5574 3892.3766 -6135.3446 -81.9797 0 0 0
DCon6 0 13.6633 1028.0713 3797.3495 -6168.4279 81.9797 0 0 0

5.2 Story Results

Table 5.2 - Story Drifts

Load X Y Z
Story Direction Drift Label
Case/Combo m m m
Roof Dead Y 0.000301 139 5 3.75 8.16
Roof Live Y 0.000209 139 5 3.75 8.16
Roof SDL Y 0.000644 140 7 3.75 8.16
Roof Wind X 1.2E-05 141 8 3.75 8.16
Roof Wind Y 1.1E-05 141 8 3.75 8.16
Roof SLS X 4.3E-05 141 8 3.75 8.16
Roof SLS Y 0.000161 141 8 3.75 8.16
Roof Total DL X 6.5E-05 141 8 3.75 8.16
Roof Total DL Y 0.000346 140 7 3.75 8.16
Roof DStlS1 X 9.1E-05 141 8 3.75 8.16
Roof DStlS1 Y 0.000485 140 7 3.75 8.16
Roof DStlS2 X 6.1E-05 141 8 3.75 8.16
Roof DStlS2 Y 0.000141 141 8 3.75 8.16
Roof DStlS3 X 5.6E-05 141 8 3.75 8.16
Roof DStlS3 Y 0.000228 141 8 3.75 8.16

Page 63 of 80
Analysis Results 8/31/2018

Table 5.2 - Story Drifts (continued)

Load X Y Z
Story Direction Drift Label
Case/Combo m m m
Roof DStlS4 X 7.9E-05 141 8 3.75 8.16
Roof DStlS4 Y 0.000249 141 8 3.75 8.16
Roof DStlS5 X 4.7E-05 141 8 3.75 8.16
Roof DStlS5 Y 0.000304 140 7 3.75 8.16
Roof DStlS6 X 7E-05 141 8 3.75 8.16
Roof DStlS6 Y 0.00032 140 7 3.75 8.16
Roof DStlD1 X 6.5E-05 141 8 3.75 8.16
Roof DStlD1 Y 0.000346 140 7 3.75 8.16
Roof DStlD2 X 5.5E-05 141 8 3.75 8.16
Roof DStlD2 Y 0.000172 141 8 3.75 8.16
Roof DCon1 X 9.1E-05 141 8 3.75 8.16
Roof DCon1 Y 0.000485 140 7 3.75 8.16
Roof DCon2 X 6.1E-05 141 8 3.75 8.16
Roof DCon2 Y 0.000141 141 8 3.75 8.16
Roof DCon3 X 5.6E-05 141 8 3.75 8.16
Roof DCon3 Y 0.000228 141 8 3.75 8.16
Roof DCon4 X 7.9E-05 141 8 3.75 8.16
Roof DCon4 Y 0.000249 141 8 3.75 8.16
Roof DCon5 X 4.7E-05 141 8 3.75 8.16
Roof DCon5 Y 0.000304 140 7 3.75 8.16
Roof DCon6 X 7E-05 141 8 3.75 8.16
Roof DCon6 Y 0.00032 140 7 3.75 8.16
Story1 Dead X 0.000445 15 0 5 4.5
Story1 Dead Y 0.000338 41 10 0 4.5
Story1 Live Y 0.000204 48 8 7.5 4.5
Story1 SDL X 0.001864 31 12 4.1667 4.5
Story1 Wind Y 0.00079 49 10 7.5 4.5
Story1 SLS Y 0.001414 40 8 0 4.5
Story1 Total DL X 0.001881 30 12 3.3333 4.5
Story1 Total DL Y 0.001146 46 5 7.5 4.5
Story1 DStlS1 X 0.002633 30 12 3.3333 4.5
Story1 DStlS1 Y 0.001604 46 5 7.5 4.5
Story1 DStlS2 X 0.003105 30 12 3.3333 4.5
Story1 DStlS2 Y 0.00167 48 8 7.5 4.5
Story1 DStlS3 Y 0.001637 40 8 0 4.5
Story1 DStlS4 X 0.002758 30 12 3.3333 4.5
Story1 DStlS4 Y 0.001668 48 8 7.5 4.5
Story1 DStlS5 Y 0.001374 41 10 0 4.5
Story1 DStlS6 Y 0.001403 49 10 7.5 4.5
Story1 DStlD1 X 0.001881 30 12 3.3333 4.5
Story1 DStlD1 Y 0.001146 46 5 7.5 4.5
Story1 DStlD2 X 0.002411 30 12 3.3333 4.5
Story1 DStlD2 Y 0.001323 48 8 7.5 4.5
Story1 DCon1 X 0.002633 30 12 3.3333 4.5
Story1 DCon1 Y 0.001604 46 5 7.5 4.5

Page 64 of 80
Analysis Results 8/31/2018

Table 5.2 - Story Drifts (continued)

Load X Y Z
Story Direction Drift Label
Case/Combo m m m
Story1 DCon2 X 0.003105 30 12 3.3333 4.5
Story1 DCon2 Y 0.00167 48 8 7.5 4.5
Story1 DCon3 Y 0.001637 40 8 0 4.5
Story1 DCon4 X 0.002758 30 12 3.3333 4.5
Story1 DCon4 Y 0.001668 48 8 7.5 4.5
Story1 DCon5 Y 0.001374 41 10 0 4.5
Story1 DCon6 Y 0.001403 49 10 7.5 4.5
1F Dead X 0.000212 13 12 5 4
1F Dead Y 0.000442 9 6 7.5 4
1F Live X 0.000215 13 12 5 4
1F Live Y 0.000333 9 6 7.5 4
1F SDL X 0.000103 7 0 7.5 4
1F Wind Y 0.000297 11 12 7.5 4
1F SLS Y 0.000356 11 12 7.5 4
1F Total DL X 0.000122 13 12 5 4
1F Total DL Y 0.00035 3 6 0 4
1F DStlS1 X 0.000171 13 12 5 4
1F DStlS1 Y 0.00049 3 6 0 4
1F DStlS2 X 0.000491 13 12 5 4
1F DStlS2 Y 0.000113 9 6 7.5 4
1F DStlS3 Y 0.000367 11 12 7.5 4
1F DStlS4 Y 0.000368 5 12 0 4
1F DStlS5 Y 0.000417 10 9 7.5 4
1F DStlS6 Y 0.000436 4 9 0 4
1F DStlD1 X 0.000122 13 12 5 4
1F DStlD1 Y 0.00035 3 6 0 4
1F DStlD2 X 0.000337 13 12 5 4
1F DStlD2 Y 0.000142 4 9 0 4
1F DCon1 X 0.000171 13 12 5 4
1F DCon1 Y 0.00049 3 6 0 4
1F DCon2 X 0.000491 13 12 5 4
1F DCon2 Y 0.000113 9 6 7.5 4
1F DCon3 Y 0.000367 11 12 7.5 4
1F DCon4 Y 0.000368 5 12 0 4
1F DCon5 Y 0.000417 10 9 7.5 4
1F DCon6 Y 0.000436 4 9 0 4
GF Dead X 6E-06 11 12 7.5 1
GF Dead Y 2.3E-05 9 6 7.5 1
GF Live X 6E-06 13 12 5 1
GF Live Y 2.4E-05 9 6 7.5 1
GF SDL X 2E-06 7 0 7.5 1
GF SDL Y 1E-06 7 0 7.5 1
GF Wind Y 4.6E-05 7 0 7.5 1
GF SLS Y 8.3E-05 3 6 0 1
GF Total DL Y 2.3E-05 9 6 7.5 1

Page 65 of 80
Analysis Results 8/31/2018

Table 5.2 - Story Drifts (continued)

Load X Y Z
Story Direction Drift Label
Case/Combo m m m
GF DStlS1 Y 3.2E-05 9 6 7.5 1
GF DStlS2 X 2E-05 11 12 7.5 1
GF DStlS2 Y 6.5E-05 9 6 7.5 1
GF DStlS3 Y 8.8E-05 3 6 0 1
GF DStlS4 Y 8.8E-05 9 6 7.5 1
GF DStlS5 Y 5.7E-05 3 6 0 1
GF DStlS6 Y 5.8E-05 9 6 7.5 1
GF DStlD1 Y 2.3E-05 9 6 7.5 1
GF DStlD2 X 1.4E-05 11 12 7.5 1
GF DStlD2 Y 4.6E-05 9 6 7.5 1
GF DCon1 Y 3.2E-05 9 6 7.5 1
GF DCon2 X 2E-05 11 12 7.5 1
GF DCon2 Y 6.5E-05 9 6 7.5 1
GF DCon3 Y 8.8E-05 3 6 0 1
GF DCon4 Y 8.8E-05 9 6 7.5 1
GF DCon5 Y 5.7E-05 3 6 0 1
GF DCon6 Y 5.8E-05 9 6 7.5 1

Table 5.3 - Story Max/Avg Drifts

Max
Load Avg Drift
Story Direction Drift Ratio
Case/Combo mm
mm
Roof Dead Y 1.102 1 1.102
Roof Live Y 0.764 0.677 1.128
Roof SDL Y 2.356 2.226 1.059
Roof Wind X 0.043 0.022 1.989
Roof Wind Y 0.039 0.033 1.182
Roof SLS X 0.156 0.145 1.078
Roof SLS Y 0.589 0.517 1.14
Roof Total DL X 0.238 0.155 1.528
Roof Total DL Y 1.268 1.23 1.031
Roof DStlS1 X 0.333 0.218 1.528
Roof DStlS1 Y 1.775 1.722 1.031
Roof DStlS2 X 0.225 0.205 1.097
Roof DStlS2 Y 0.518 0.389 1.331
Roof DStlS3 X 0.204 0.176 1.158
Roof DStlS3 Y 0.833 0.762 1.093
Roof DStlS4 X 0.291 0.22 1.323
Roof DStlS4 Y 0.911 0.828 1.1
Roof DStlS5 X 0.17 0.118 1.443
Roof DStlS5 Y 1.113 1.076 1.034
Roof DStlS6 X 0.257 0.162 1.59
Roof DStlS6 Y 1.17 1.138 1.028
Roof DStlD1 X 0.238 0.155 1.528
Roof DStlD1 Y 1.268 1.23 1.031

Page 66 of 80
Analysis Results 8/31/2018

Table 5.3 - Story Max/Avg Drifts (continued)

Max
Load Avg Drift
Story Direction Drift Ratio
Case/Combo mm
mm
Roof DStlD2 X 0.2 0.167 1.198
Roof DStlD2 Y 0.628 0.55 1.142
Roof DCon1 X 0.333 0.218 1.528
Roof DCon1 Y 1.775 1.722 1.031
Roof DCon2 X 0.225 0.205 1.097
Roof DCon2 Y 0.518 0.389 1.331
Roof DCon3 X 0.204 0.176 1.158
Roof DCon3 Y 0.833 0.762 1.093
Roof DCon4 X 0.291 0.22 1.323
Roof DCon4 Y 0.911 0.828 1.1
Roof DCon5 X 0.17 0.118 1.443
Roof DCon5 Y 1.113 1.076 1.034
Roof DCon6 X 0.257 0.162 1.59
Roof DCon6 Y 1.17 1.138 1.028
Story1 Dead X 0.223 0.0004194 531.03
Story1 Dead Y 0.169 0.003 51.477
Story1 Live Y 0.102 0.001 76.241
Story1 SDL X 0.932 0.006 161.956
Story1 Wind Y 0.395 0.201 1.966
Story1 SLS Y 0.707 0.053 13.361
Story1 Total DL X 0.94 0.004 218.692
Story1 Total DL Y 0.573 0.001 408.962
Story1 DStlS1 X 1.316 0.006 218.692
Story1 DStlS1 Y 0.802 0.002 408.962
Story1 DStlS2 X 1.553 0.005 305.213
Story1 DStlS2 Y 0.835 0.004 186.506
Story1 DStlS3 Y 0.818 0.053 15.577
Story1 DStlS4 X 1.379 0.006 223.929
Story1 DStlS4 Y 0.834 0.06 13.929
Story1 DStlS5 Y 0.687 0.122 5.646
Story1 DStlS6 Y 0.701 0.126 5.554
Story1 DStlD1 X 0.94 0.004 218.692
Story1 DStlD1 Y 0.573 0.001 408.962
Story1 DStlD2 X 1.205 0.004 283.351
Story1 DStlD2 Y 0.662 0.003 201.441
Story1 DCon1 X 1.316 0.006 218.692
Story1 DCon1 Y 0.802 0.002 408.962
Story1 DCon2 X 1.553 0.005 305.213
Story1 DCon2 Y 0.835 0.004 186.506
Story1 DCon3 Y 0.818 0.053 15.577
Story1 DCon4 X 1.379 0.006 223.929
Story1 DCon4 Y 0.834 0.06 13.929
Story1 DCon5 Y 0.687 0.122 5.646
Story1 DCon6 Y 0.701 0.126 5.554

Page 67 of 80
Analysis Results 8/31/2018

Table 5.3 - Story Max/Avg Drifts (continued)

Max
Load Avg Drift
Story Direction Drift Ratio
Case/Combo mm
mm
1F Dead X 0.635 0.000369 1720.209
1F Dead Y 1.327 0.001 1898.75
1F Live X 0.645 0.001 670.176
1F Live Y 0.998 0.001 1231.415
1F SDL X 0.31 0.008 37.54
1F Wind Y 0.891 0.489 1.823
1F SLS Y 1.067 0.55 1.94
1F Total DL X 0.366 0.005 73.756
1F Total DL Y 1.051 0.001 1008.982
1F DStlS1 X 0.513 0.007 73.756
1F DStlS1 Y 1.471 0.001 1008.982
1F DStlS2 X 1.472 0.007 196.297
1F DStlS2 Y 0.339 0.003 133.046
1F DStlS3 Y 1.1 0.472 2.329
1F DStlS4 Y 1.105 0.458 2.411
1F DStlS5 Y 1.25 0.216 5.779
1F DStlS6 Y 1.307 0.225 5.818
1F DStlD1 X 0.366 0.005 73.756
1F DStlD1 Y 1.051 0.001 1008.982
1F DStlD2 X 1.012 0.006 170.638
1F DStlD2 Y 0.427 0.007 57.397
1F DCon1 X 0.513 0.007 73.756
1F DCon1 Y 1.471 0.001 1008.982
1F DCon2 X 1.472 0.007 196.297
1F DCon2 Y 0.339 0.003 133.046
1F DCon3 Y 1.1 0.472 2.329
1F DCon4 Y 1.105 0.458 2.411
1F DCon5 Y 1.25 0.216 5.779
1F DCon6 Y 1.307 0.225 5.818
GF Dead X 0.006 3.807E-05 159.74
GF Dead Y 0.023 9.691E-05 232.561
GF Live X 0.006 2.489E-05 259.774
GF Live Y 0.024 0.0001091 216.978
GF SDL X 0.002 2.943E-05 65.005
GF SDL Y 0.001 6.43E-05 13.695
GF Wind Y 0.046 0.041 1.107
GF SLS Y 0.083 0.037 2.256
GF Total DL Y 0.023 0.0001417 160.832
GF DStlS1 Y 0.032 0.0001983 160.832
GF DStlS2 X 0.02 5.216E-05 380.23
GF DStlS2 Y 0.065 0.0003446 189.28
GF DStlS3 Y 0.088 0.037 2.38
GF DStlS4 Y 0.088 0.037 2.356
GF DStlS5 Y 0.057 0.037 1.553

Page 68 of 80
Analysis Results 8/31/2018

Table 5.3 - Story Max/Avg Drifts (continued)

Max
Load Avg Drift
Story Direction Drift Ratio
Case/Combo mm
mm
GF DStlS6 Y 0.058 0.037 1.546
GF DStlD1 Y 0.023 0.0001417 160.832
GF DStlD2 X 0.014 3.476E-05 413.664
GF DStlD2 Y 0.046 0.0002508 185.262
GF DCon1 Y 0.032 0.0001983 160.832
GF DCon2 X 0.02 5.216E-05 380.23
GF DCon2 Y 0.065 0.0003446 189.28
GF DCon3 Y 0.088 0.037 2.38
GF DCon4 Y 0.088 0.037 2.356
GF DCon5 Y 0.057 0.037 1.553
GF DCon6 Y 0.058 0.037 1.546

Table 5.4 - Story Forces

Load P VX VY T MX MY
Story Location
Case/Combo kN kN kN kN-m kN-m kN-m
Roof Dead Top 0.258 0 0 0 0.9674 -1.5479
Roof Dead Bottom 4.6359 -0.135 -0.0593 0.1329 17.3759 -28.174
Roof Live Top 0 0 0 0 0 0
Roof Live Bottom 13.2577 0.0746 -0.0112 -0.3596 49.3995 -78.9303
Roof SDL Top 0 0 0 0 0 0
Roof SDL Bottom 34.8427 1.2361 0.3116 -2.741 128.9574 -203.461
Roof Wind Top 0.8108 0 -3.4291 -20.5745 3.0404 -4.8647
Roof Wind Bottom 0.1355 0.0267 -5.2514 -30.9413 9.9369 -0.6392
Roof SLS Top 1.0688 0 -3.4291 -20.5745 4.0079 -6.4126
Roof SLS Bottom 52.8717 1.2024 -5.0104 -33.909 205.6697 -311.2046
Roof Total DL Top 0.258 0 0 0 0.9674 -1.5479
Roof Total DL Bottom 39.4786 1.1011 0.2522 -2.6081 146.3333 -231.635
Roof DStlS1 Top 0.3612 0 0 0 1.3544 -2.1671
Roof DStlS1 Bottom 55.27 1.5415 0.3531 -3.6514 204.8667 -324.2891
Roof DStlS2 Top 0.3096 0 0 0 1.1609 -1.8575
Roof DStlS2 Bottom 68.5865 1.4407 0.2848 -3.7052 254.6392 -404.2505
Roof DStlS3 Top 1.1204 0 -3.4291 -20.5745 4.2014 -6.7222
Roof DStlS3 Bottom 60.7674 1.4227 -4.9599 -34.4307 234.9364 -357.5316
Roof DStlS4 Top -0.5012 0 3.4291 20.5745 -1.8795 3.0072
Roof DStlS4 Bottom 60.4965 1.3692 5.5429 27.4519 215.0626 -356.2531
Roof DStlS5 Top 1.043 0 -3.4291 -20.5745 3.9111 -6.2578
Roof DStlS5 Bottom 35.6662 1.0177 -5.0244 -33.2886 141.6369 -209.1108
Roof DStlS6 Top -0.5786 0 3.4291 20.5745 -2.1698 3.4716
Roof DStlS6 Bottom 35.3952 0.9643 5.4784 28.594 121.7631 -207.8323
Roof DStlD1 Top 0.258 0 0 0 0.9674 -1.5479
Roof DStlD1 Bottom 39.4786 1.1011 0.2522 -2.6081 146.3333 -231.635
Roof DStlD2 Top 0.258 0 0 0 0.9674 -1.5479
Roof DStlD2 Bottom 52.7362 1.1757 0.241 -2.9678 195.7328 -310.5653
Roof DCon1 Top 0.3612 0 0 0 1.3544 -2.1671

Page 69 of 80
Analysis Results 8/31/2018

Table 5.4 - Story Forces (continued)

Load P VX VY T MX MY
Story Location
Case/Combo kN kN kN kN-m kN-m kN-m
Roof DCon1 Bottom 55.27 1.5415 0.3531 -3.6514 204.8667 -324.2891
Roof DCon2 Top 0.3096 0 0 0 1.1609 -1.8575
Roof DCon2 Bottom 68.5865 1.4407 0.2848 -3.7052 254.6392 -404.2505
Roof DCon3 Top 1.1204 0 -3.4291 -20.5745 4.2014 -6.7222
Roof DCon3 Bottom 60.7674 1.4227 -4.9599 -34.4307 234.9364 -357.5316
Roof DCon4 Top -0.5012 0 3.4291 20.5745 -1.8795 3.0072
Roof DCon4 Bottom 60.4965 1.3692 5.5429 27.4519 215.0626 -356.2531
Roof DCon5 Top 1.043 0 -3.4291 -20.5745 3.9111 -6.2578
Roof DCon5 Bottom 35.6662 1.0177 -5.0244 -33.2886 141.6369 -209.1108
Roof DCon6 Top -0.5786 0 3.4291 20.5745 -2.1698 3.4716
Roof DCon6 Bottom 35.3952 0.9643 5.4784 28.594 121.7631 -207.8323
Story1 Dead Top 5.8867 -0.135 -0.0593 0.1329 22.073 -35.6792
Story1 Dead Bottom 7.0964 -0.135 -0.0593 0.1329 26.5594 -43.0047
Story1 Live Top 13.2577 0.0746 -0.0112 -0.3596 49.3995 -78.9303
Story1 Live Bottom 13.2577 0.0746 -0.0112 -0.3596 49.4051 -78.893
Story1 SDL Top 34.8427 1.2361 0.3116 -2.741 128.9574 -203.461
Story1 SDL Bottom 34.8427 1.2361 0.3116 -2.741 128.8016 -202.843
Story1 Wind Top -2.2988 0.0267 -8.8765 -52.6916 -13.1198 13.9663
Story1 Wind Bottom -2.2988 0.0267 -8.8765 -52.6916 -8.6815 13.9797
Story1 SLS Top 51.6883 1.2024 -8.6354 -55.6593 187.3102 -304.1043
Story1 SLS Bottom 52.898 1.2024 -8.6354 -55.6593 196.0845 -310.761
Story1 Total DL Top 40.7294 1.1011 0.2522 -2.6081 151.0305 -239.1403
Story1 Total DL Bottom 41.9391 1.1011 0.2522 -2.6081 155.361 -245.8477
Story1 DStlS1 Top 57.0212 1.5415 0.3531 -3.6514 211.4427 -334.7964
Story1 DStlS1 Bottom 58.7147 1.5415 0.3531 -3.6514 217.5054 -344.1868
Story1 DStlS2 Top 70.0876 1.4407 0.2848 -3.7052 260.2757 -413.2568
Story1 DStlS2 Bottom 71.5392 1.4407 0.2848 -3.7052 265.4813 -421.246
Story1 DStlS3 Top 59.8342 1.4227 -8.585 -56.181 217.5163 -351.9323
Story1 DStlS3 Bottom 61.2858 1.4227 -8.585 -56.181 227.1567 -359.9306
Story1 DStlS4 Top 64.4318 1.3692 9.168 49.2022 243.7558 -379.8649
Story1 DStlS4 Bottom 65.8834 1.3692 9.168 49.2022 244.5198 -387.8899
Story1 DStlS5 Top 34.3577 1.0177 -8.6494 -55.0389 122.8077 -201.26
Story1 DStlS5 Bottom 35.4464 1.0177 -8.6494 -55.0389 131.1434 -207.2833
Story1 DStlS6 Top 38.9553 0.9643 9.1035 50.3443 149.0472 -229.1926
Story1 DStlS6 Bottom 40.044 0.9643 9.1035 50.3443 148.5064 -235.2426
Story1 DStlD1 Top 40.7294 1.1011 0.2522 -2.6081 151.0305 -239.1403
Story1 DStlD1 Bottom 41.9391 1.1011 0.2522 -2.6081 155.361 -245.8477
Story1 DStlD2 Top 53.9871 1.1757 0.241 -2.9678 200.43 -318.0706
Story1 DStlD2 Bottom 55.1968 1.1757 0.241 -2.9678 204.7661 -324.7407
Story1 DCon1 Top 57.0212 1.5415 0.3531 -3.6514 211.4427 -334.7964
Story1 DCon1 Bottom 58.7147 1.5415 0.3531 -3.6514 217.5054 -344.1868
Story1 DCon2 Top 70.0876 1.4407 0.2848 -3.7052 260.2757 -413.2568
Story1 DCon2 Bottom 71.5392 1.4407 0.2848 -3.7052 265.4813 -421.246
Story1 DCon3 Top 59.8342 1.4227 -8.585 -56.181 217.5163 -351.9323
Story1 DCon3 Bottom 61.2858 1.4227 -8.585 -56.181 227.1567 -359.9306

Page 70 of 80
Analysis Results 8/31/2018

Table 5.4 - Story Forces (continued)

Load P VX VY T MX MY
Story Location
Case/Combo kN kN kN kN-m kN-m kN-m
Story1 DCon4 Top 64.4318 1.3692 9.168 49.2022 243.7558 -379.8649
Story1 DCon4 Bottom 65.8834 1.3692 9.168 49.2022 244.5198 -387.8899
Story1 DCon5 Top 34.3577 1.0177 -8.6494 -55.0389 122.8077 -201.26
Story1 DCon5 Bottom 35.4464 1.0177 -8.6494 -55.0389 131.1434 -207.2833
Story1 DCon6 Top 38.9553 0.9643 9.1035 50.3443 149.0472 -229.1926
Story1 DCon6 Bottom 40.044 0.9643 9.1035 50.3443 148.5064 -235.2426
1F Dead Top 15.0994 0 0 0 56.5496 -90.5965
1F Dead Bottom 105.8194 0 0 0 396.7496 -634.9165
1F Live Top 32.6692 0 0 0 122.5097 -196.0155
1F Live Bottom 32.6692 0 0 0 122.5097 -196.0155
1F SDL Top 110.0188 0 0 0 412.5704 -660.1126
1F SDL Bottom 110.0188 0 0 0 412.5704 -660.1126
1F Wind Top -2.7569 0 -13.6633 -81.9797 -7.1396 16.5417
1F Wind Bottom -2.7569 0 -13.6633 -81.9797 33.8503 16.5417
1F SLS Top 155.0305 0 -13.6633 -81.9797 584.4901 -930.183
1F SLS Bottom 245.7505 0 -13.6633 -81.9797 965.68 -1474.503
1F Total DL Top 125.1182 0 0 0 469.12 -750.7092
1F Total DL Bottom 215.8382 0 0 0 809.32 -1295.0292
1F DStlS1 Top 175.1655 0 0 0 656.768 -1050.9929
1F DStlS1 Bottom 302.1735 0 0 0 1133.048 -1813.0409
1F DStlS2 Top 202.4126 0 0 0 758.9595 -1214.4758
1F DStlS2 Bottom 311.2766 0 0 0 1167.1995 -1867.6598
1F DStlS3 Top 180.0541 0 -13.6633 -81.9797 678.3141 -1080.3249
1F DStlS3 Bottom 288.9181 0 -13.6633 -81.9797 1127.544 -1733.5089
1F DStlS4 Top 185.568 0 13.6633 81.9797 692.5933 -1113.4082
1F DStlS4 Bottom 294.432 0 13.6633 81.9797 1059.8435 -1766.5922
1F DStlS5 Top 109.8494 0 -13.6633 -81.9797 415.0684 -659.0966
1F DStlS5 Bottom 191.4974 0 -13.6633 -81.9797 762.2383 -1148.9846
1F DStlS6 Top 115.3633 0 13.6633 81.9797 429.3476 -692.1799
1F DStlS6 Bottom 197.0113 0 13.6633 81.9797 694.5378 -1182.0679
1F DStlD1 Top 125.1182 0 0 0 469.12 -750.7092
1F DStlD1 Bottom 215.8382 0 0 0 809.32 -1295.0292
1F DStlD2 Top 157.7874 0 0 0 591.6297 -946.7247
1F DStlD2 Bottom 248.5074 0 0 0 931.8297 -1491.0447
1F DCon1 Top 175.1655 0 0 0 656.768 -1050.9929
1F DCon1 Bottom 302.1735 0 0 0 1133.048 -1813.0409
1F DCon2 Top 202.4126 0 0 0 758.9595 -1214.4758
1F DCon2 Bottom 311.2766 0 0 0 1167.1995 -1867.6598
1F DCon3 Top 180.0541 0 -13.6633 -81.9797 678.3141 -1080.3249
1F DCon3 Bottom 288.9181 0 -13.6633 -81.9797 1127.544 -1733.5089
1F DCon4 Top 185.568 0 13.6633 81.9797 692.5933 -1113.4082
1F DCon4 Bottom 294.432 0 13.6633 81.9797 1059.8435 -1766.5922
1F DCon5 Top 109.8494 0 -13.6633 -81.9797 415.0684 -659.0966
1F DCon5 Bottom 191.4974 0 -13.6633 -81.9797 762.2383 -1148.9846
1F DCon6 Top 115.3633 0 13.6633 81.9797 429.3476 -692.1799

Page 71 of 80
Analysis Results 8/31/2018

Table 5.4 - Story Forces (continued)

Load P VX VY T MX MY
Story Location
Case/Combo kN kN kN kN-m kN-m kN-m
1F DCon6 Bottom 197.0113 0 13.6633 81.9797 694.5378 -1182.0679
GF Dead Top 512.9794 0 0 0 1923.5996 -3077.8765
GF Dead Bottom 543.2194 0 0 0 2036.9996 -3259.3165
GF Live Top 463.7692 0 0 0 1739.1347 -2782.6155
GF Live Bottom 463.7692 0 0 0 1739.1347 -2782.6155
GF SDL Top 596.0188 0 0 0 2235.0704 -3576.1126
GF SDL Bottom 596.0188 0 0 0 2235.0704 -3576.1126
GF Wind Top -2.7569 0 -13.6633 -81.9797 33.8503 16.5417
GF Wind Bottom -2.7569 0 -13.6633 -81.9797 47.5135 16.5417
GF SLS Top 1570.0105 0 -13.6633 -81.9797 5931.655 -9420.063
GF SLS Bottom 1600.2505 0 -13.6633 -81.9797 6058.7182 -9601.503
GF Total DL Top 1108.9982 0 0 0 4158.67 -6653.9892
GF Total DL Bottom 1139.2382 0 0 0 4272.07 -6835.4292
GF DStlS1 Top 1552.5975 0 0 0 5822.138 -9315.5849
GF DStlS1 Bottom 1594.9335 0 0 0 5980.898 -9569.6009
GF DStlS2 Top 2072.8286 0 0 0 7773.0195 -12436.9718
GF DStlS2 Bottom 2109.1166 0 0 0 7909.0995 -12654.6998
GF DStlS3 Top 1791.8101 0 -13.6633 -81.9797 6763.389 -10750.8609
GF DStlS3 Bottom 1828.0981 0 -13.6633 -81.9797 6913.1323 -10968.5889
GF DStlS4 Top 1797.324 0 13.6633 81.9797 6695.6885 -10783.9442
GF DStlS4 Bottom 1833.612 0 13.6633 81.9797 6818.1052 -11001.6722
GF DStlS5 Top 995.3414 0 -13.6633 -81.9797 3776.6533 -5972.0486
GF DStlS5 Bottom 1022.5574 0 -13.6633 -81.9797 3892.3766 -6135.3446
GF DStlS6 Top 1000.8553 0 13.6633 81.9797 3708.9528 -6005.1319
GF DStlS6 Bottom 1028.0713 0 13.6633 81.9797 3797.3495 -6168.4279
GF DStlD1 Top 1108.9982 0 0 0 4158.67 -6653.9892
GF DStlD1 Bottom 1139.2382 0 0 0 4272.07 -6835.4292
GF DStlD2 Top 1572.7674 0 0 0 5897.8047 -9436.6047
GF DStlD2 Bottom 1603.0074 0 0 0 6011.2047 -9618.0447
GF DCon1 Top 1552.5975 0 0 0 5822.138 -9315.5849
GF DCon1 Bottom 1594.9335 0 0 0 5980.898 -9569.6009
GF DCon2 Top 2072.8286 0 0 0 7773.0195 -12436.9718
GF DCon2 Bottom 2109.1166 0 0 0 7909.0995 -12654.6998
GF DCon3 Top 1791.8101 0 -13.6633 -81.9797 6763.389 -10750.8609
GF DCon3 Bottom 1828.0981 0 -13.6633 -81.9797 6913.1323 -10968.5889
GF DCon4 Top 1797.324 0 13.6633 81.9797 6695.6885 -10783.9442
GF DCon4 Bottom 1833.612 0 13.6633 81.9797 6818.1052 -11001.6722
GF DCon5 Top 995.3414 0 -13.6633 -81.9797 3776.6533 -5972.0486
GF DCon5 Bottom 1022.5574 0 -13.6633 -81.9797 3892.3766 -6135.3446
GF DCon6 Top 1000.8553 0 13.6633 81.9797 3708.9528 -6005.1319
GF DCon6 Bottom 1028.0713 0 13.6633 81.9797 3797.3495 -6168.4279

Page 72 of 80
Analysis Results 8/31/2018

5.3 Point Results

Table 5.5 - Joint Reactions

Joint Unique Load FX FY FZ MX MY MZ

Story
Label Name Case/Combo kN kN kN kN-m kN-m kN-m
Base 1 2 Dead 2.3791 2.0786 15.5551 0 0 0
Base 1 2 Live 2.497 2.1595 7.6235 0 0 0
Base 1 2 SDL 3.1813 2.1721 34.4869 0 0 0
Base 1 2 Wind 0.1508 1.2333 -3.2483 0 0 0
Base 1 2 SLS 8.2082 7.6435 54.4171 0 0 0
Base 1 2 Total DL 5.5604 4.2507 50.0419 0 0 0
Base 1 2 DStlS1 7.7846 5.9509 70.0587 0 0 0
Base 1 2 DStlS2 10.6676 8.5559 72.2479 0 0 0
Base 1 2 DStlS3 9.3202 8.4936 64.4255 0 0 0
Base 1 2 DStlS4 9.0186 6.0269 70.9222 0 0 0
Base 1 2 DStlS5 5.1552 5.0589 41.7894 0 0 0
Base 1 2 DStlS6 4.8536 2.5923 48.2861 0 0 0
Base 1 2 DStlD1 5.5604 4.2507 50.0419 0 0 0
Base 1 2 DStlD2 8.0574 6.4101 57.6654 0 0 0
Base 1 2 DCon1 7.7846 5.9509 70.0587 0 0 0
Base 1 2 DCon2 10.6676 8.5559 72.2479 0 0 0
Base 1 2 DCon3 9.3202 8.4936 64.4255 0 0 0
Base 1 2 DCon4 9.0186 6.0269 70.9222 0 0 0
Base 1 2 DCon5 5.1552 5.0589 41.7894 0 0 0
Base 1 2 DCon6 4.8536 2.5923 48.2861 0 0 0
Base 2 4 Dead 2.063 40.7117 54.8886 -11.2719 0.4575 -0.0315
Base 2 4 Live 2.1346 43.9415 50.2635 -12.1774 0.4679 -0.0314
Base 2 4 SDL -0.2942 5.9254 51.2659 -1.6954 -0.1059 0.0103
Base 2 4 Wind 0.3982 -2.9912 -0.858 2.1943 0.189 0.0188
Base 2 4 SLS 4.3016 87.5874 155.56 -22.9504 1.0084 -0.0339
Base 2 4 Total DL 1.7688 46.637 106.1545 -12.9673 0.3515 -0.0212
Base 2 4 DStlS1 2.4763 65.2918 148.6163 -18.1542 0.4922 -0.0297
Base 2 4 DStlS2 5.5379 126.2708 207.807 -35.0445 1.1705 -0.0758
Base 2 4 DStlS3 4.6554 96.9148 176.7909 -25.5438 1.0787 -0.0381
Base 2 4 DStlS4 3.8589 102.8971 178.5069 -29.9324 0.7008 -0.0757
Base 2 4 DStlS5 1.9901 38.9822 94.6811 -9.4763 0.5054 -0.0003
Base 2 4 DStlS6 1.1937 44.9645 96.3971 -13.8648 0.1274 -0.0379
Base 2 4 DStlD1 1.7688 46.637 106.1545 -12.9673 0.3515 -0.0212
Base 2 4 DStlD2 3.9034 90.5785 156.418 -25.1446 0.8194 -0.0527
Base 2 4 DCon1 2.4763 65.2918 148.6163 -18.1542 0.4922 -0.0297
Base 2 4 DCon2 5.5379 126.2708 207.807 -35.0445 1.1705 -0.0758
Base 2 4 DCon3 4.6554 96.9148 176.7909 -25.5438 1.0787 -0.0381
Base 2 4 DCon4 3.8589 102.8971 178.5069 -29.9324 0.7008 -0.0757
Base 2 4 DCon5 1.9901 38.9822 94.6811 -9.4763 0.5054 -0.0003
Base 2 4 DCon6 1.1937 44.9645 96.3971 -13.8648 0.1274 -0.0379
Base 3 6 Dead 0.0023 54.6 63.2746 -15.0915 0.002 -0.0006
Base 3 6 Live 0.0042 58.3877 59.8088 -16.153 0.0019 -0.0008
Base 3 6 SDL 0.0125 6.2841 55.8537 -1.8179 0.0007 -0.0005
Base 3 6 Wind 0.0019 -3.5773 -0.1796 2.285 0.0012 -4.061E-05

Page 73 of 80
Analysis Results 8/31/2018

Table 5.5 - Joint Reactions (continued)

Joint Unique Load FX FY FZ MX MY MZ

Story
Label Name Case/Combo kN kN kN kN-m kN-m kN-m
Base 3 6 SLS 0.021 115.6944 178.7574 -30.7774 0.0058 -0.002
Base 3 6 Total DL 0.0149 60.8841 119.1283 -16.9094 0.0028 -0.0011
Base 3 6 DStlS1 0.0208 85.2377 166.7796 -23.6732 0.0039 -0.0016
Base 3 6 DStlS2 0.0246 166.4812 238.6479 -46.1361 0.0063 -0.0026
Base 3 6 DStlS3 0.0239 127.8713 202.583 -34.1592 0.0064 -0.0022
Base 3 6 DStlS4 0.0202 135.0259 202.9423 -38.7293 0.004 -0.0021
Base 3 6 DStlS5 0.0152 51.2184 107.0358 -12.9334 0.0037 -0.001
Base 3 6 DStlS6 0.0115 58.373 107.3951 -17.5035 0.0013 -0.001
Base 3 6 DStlD1 0.0149 60.8841 119.1283 -16.9094 0.0028 -0.0011
Base 3 6 DStlD2 0.0191 119.2717 178.937 -33.0624 0.0046 -0.0019
Base 3 6 DCon1 0.0208 85.2377 166.7796 -23.6732 0.0039 -0.0016
Base 3 6 DCon2 0.0246 166.4812 238.6479 -46.1361 0.0063 -0.0026
Base 3 6 DCon3 0.0239 127.8713 202.583 -34.1592 0.0064 -0.0022
Base 3 6 DCon4 0.0202 135.0259 202.9423 -38.7293 0.004 -0.0021
Base 3 6 DCon5 0.0152 51.2184 107.0358 -12.9334 0.0037 -0.001
Base 3 6 DCon6 0.0115 58.373 107.3951 -17.5035 0.0013 -0.001
Base 4 8 Dead -2.0596 40.7202 54.9023 -11.2744 -0.4537 0.0303
Base 4 8 Live -2.1255 43.9038 50.3316 -12.1672 -0.4639 0.0299
Base 4 8 SDL 0.3322 5.6593 51.5773 -1.6227 0.1111 -0.0107
Base 4 8 Wind -0.3934 -2.9864 -0.9118 2.192 -0.1862 -0.0182
Base 4 8 SLS -4.2463 87.2969 155.8994 -22.8722 -0.9928 0.0314
Base 4 8 Total DL -1.7274 46.3795 106.4797 -12.8971 -0.3427 0.0197
Base 4 8 DStlS1 -2.4184 64.9313 149.0715 -18.0559 -0.4797 0.0275
Base 4 8 DStlS2 -5.4737 125.9014 208.3061 -34.944 -1.1535 0.0715
Base 4 8 DStlS3 -4.5918 96.5727 177.1953 -25.4516 -1.0613 0.0354
Base 4 8 DStlS4 -3.805 102.5456 179.019 -29.8357 -0.689 0.0717
Base 4 8 DStlS5 -1.9481 38.7551 94.9199 -9.4153 -0.4946 -0.0005
Base 4 8 DStlS6 -1.1613 44.728 96.7435 -13.7994 -0.1222 0.0359
Base 4 8 DStlD1 -1.7274 46.3795 106.4797 -12.8971 -0.3427 0.0197
Base 4 8 DStlD2 -3.8529 90.2833 156.8112 -25.0643 -0.8066 0.0496
Base 4 8 DCon1 -2.4184 64.9313 149.0715 -18.0559 -0.4797 0.0275
Base 4 8 DCon2 -5.4737 125.9014 208.3061 -34.944 -1.1535 0.0715
Base 4 8 DCon3 -4.5918 96.5727 177.1953 -25.4516 -1.0613 0.0354
Base 4 8 DCon4 -3.805 102.5456 179.019 -29.8357 -0.689 0.0717
Base 4 8 DCon5 -1.9481 38.7551 94.9199 -9.4153 -0.4946 -0.0005
Base 4 8 DCon6 -1.1613 44.728 96.7435 -13.7994 -0.1222 0.0359
Base 5 10 Dead -2.3841 2.0814 15.5579 0 0 0
Base 5 10 Live -2.5082 2.1557 7.5952 0 0 0
Base 5 10 SDL -3.2175 2.134 34.3131 0 0 0
Base 5 10 Wind -0.1664 1.2499 -3.2169 0 0 0
Base 5 10 SLS -8.2763 7.6209 54.2494 0 0 0
Base 5 10 Total DL -5.6016 4.2154 49.871 0 0 0
Base 5 10 DStlS1 -7.8423 5.9015 69.8194 0 0 0
Base 5 10 DStlS2 -10.7351 8.5075 71.9976 0 0 0
Base 5 10 DStlS3 -9.3966 8.464 64.2236 0 0 0

Page 74 of 80
Analysis Results 8/31/2018

Table 5.5 - Joint Reactions (continued)

Joint Unique Load FX FY FZ MX MY MZ

Story
Label Name Case/Combo kN kN kN kN-m kN-m kN-m
Base 5 10 DStlS4 -9.0638 5.9642 70.6573 0 0 0
Base 5 10 DStlS5 -5.2079 5.0437 41.667 0 0 0
Base 5 10 DStlS6 -4.875 2.5439 48.1008 0 0 0
Base 5 10 DStlD1 -5.6016 4.2154 49.871 0 0 0
Base 5 10 DStlD2 -8.1099 6.371 57.4662 0 0 0
Base 5 10 DCon1 -7.8423 5.9015 69.8194 0 0 0
Base 5 10 DCon2 -10.7351 8.5075 71.9976 0 0 0
Base 5 10 DCon3 -9.3966 8.464 64.2236 0 0 0
Base 5 10 DCon4 -9.0638 5.9642 70.6573 0 0 0
Base 5 10 DCon5 -5.2079 5.0437 41.667 0 0 0
Base 5 10 DCon6 -4.875 2.5439 48.1008 0 0 0
Base 7 14 Dead 2.3874 -2.0761 15.5702 0 0 0
Base 7 14 Live 2.5024 -2.1637 7.6373 0 0 0
Base 7 14 SDL 3.1659 -2.2109 34.423 0 0 0
Base 7 14 Wind -0.2392 1.2667 2.0422 0 0 0
Base 7 14 SLS 7.8164 -5.1839 59.6727 0 0 0
Base 7 14 Total DL 5.5533 -4.2869 49.9932 0 0 0
Base 7 14 DStlS1 7.7746 -6.0017 69.9905 0 0 0
Base 7 14 DStlS2 10.6677 -8.6062 72.2115 0 0 0
Base 7 14 DStlS3 8.927 -6.0413 69.6713 0 0 0
Base 7 14 DStlS4 9.4055 -8.5747 65.5869 0 0 0
Base 7 14 DStlS5 4.7587 -2.5915 47.0361 0 0 0
Base 7 14 DStlS6 5.2372 -5.125 42.9517 0 0 0
Base 7 14 DStlD1 5.5533 -4.2869 49.9932 0 0 0
Base 7 14 DStlD2 8.0556 -6.4506 57.6305 0 0 0
Base 7 14 DCon1 7.7746 -6.0017 69.9905 0 0 0
Base 7 14 DCon2 10.6677 -8.6062 72.2115 0 0 0
Base 7 14 DCon3 8.927 -6.0413 69.6713 0 0 0
Base 7 14 DCon4 9.4055 -8.5747 65.5869 0 0 0
Base 7 14 DCon5 4.7587 -2.5915 47.0361 0 0 0
Base 7 14 DCon6 5.2372 -5.125 42.9517 0 0 0
Base 8 16 Dead 2.049 -40.7275 54.9176 11.2706 0.4513 0.0315
Base 8 16 Live 2.1192 -43.9573 50.3124 12.1751 0.4612 0.0314
Base 8 16 SDL -0.2988 -5.9191 51.3737 1.6901 -0.1071 -0.0106
Base 8 16 Wind -0.4489 -3.0865 0.5486 2.2191 -0.1993 0.0191
Base 8 16 SLS 3.4205 -93.6904 157.1523 27.3549 0.606 0.0714
Base 8 16 Total DL 1.7502 -46.6466 106.2913 12.9607 0.3442 0.0209
Base 8 16 DStlS1 2.4503 -65.3052 148.8078 18.1449 0.4818 0.0293
Base 8 16 DStlS2 5.4909 -126.3076 208.0494 35.033 1.1509 0.0753
Base 8 16 DStlS3 3.7705 -103.0197 178.4105 29.947 0.6749 0.0756
Base 8 16 DStlS4 4.6684 -96.8467 177.3134 25.5089 1.0735 0.0374
Base 8 16 DStlS5 1.1263 -45.0684 96.2107 13.8837 0.1104 0.0379
Base 8 16 DStlS6 2.0241 -38.8954 95.1136 9.4455 0.509 -0.0002
Base 8 16 DStlD1 1.7502 -46.6466 106.2913 12.9607 0.3442 0.0209
Base 8 16 DStlD2 3.8694 -90.6039 156.6037 25.1358 0.8054 0.0523

Page 75 of 80
Analysis Results 8/31/2018

Table 5.5 - Joint Reactions (continued)

Joint Unique Load FX FY FZ MX MY MZ

Story
Label Name Case/Combo kN kN kN kN-m kN-m kN-m
Base 8 16 DCon1 2.4503 -65.3052 148.8078 18.1449 0.4818 0.0293
Base 8 16 DCon2 5.4909 -126.3076 208.0494 35.033 1.1509 0.0753
Base 8 16 DCon3 3.7705 -103.0197 178.4105 29.947 0.6749 0.0756
Base 8 16 DCon4 4.6684 -96.8467 177.3134 25.5089 1.0735 0.0374
Base 8 16 DCon5 1.1263 -45.0684 96.2107 13.8837 0.1104 0.0379
Base 8 16 DCon6 2.0241 -38.8954 95.1136 9.4455 0.509 -0.0002
Base 9 18 Dead 0.0024 -54.5828 63.2716 15.08 0.0019 0.0006
Base 9 18 Live 0.0044 -58.3685 59.8054 16.1401 0.0019 0.0008
Base 9 18 SDL 0.0131 -6.2764 55.8516 1.8127 0.002 0.0004
Base 9 18 Wind -0.0052 -3.7596 0.0212 2.3337 -0.0021 4.092E-06
Base 9 18 SLS 0.0147 -122.9873 178.9497 35.3665 0.0037 0.0019
Base 9 18 Total DL 0.0155 -60.8592 119.1232 16.8927 0.0039 0.001
Base 9 18 DStlS1 0.0217 -85.2029 166.7724 23.6498 0.0054 0.0015
Base 9 18 DStlS2 0.0257 -166.4206 238.6365 46.0954 0.0077 0.0025
Base 9 18 DStlS3 0.0178 -135.1591 202.7744 38.745 0.0044 0.0021
Base 9 18 DStlS4 0.0283 -127.64 202.732 34.0777 0.0087 0.0021
Base 9 18 DStlS5 0.0087 -58.5329 107.232 17.5371 0.0014 0.0009
Base 9 18 DStlS6 0.0192 -51.0137 107.1897 12.8698 0.0056 0.0009
Base 9 18 DStlD1 0.0155 -60.8592 119.1232 16.8927 0.0039 0.001
Base 9 18 DStlD2 0.0199 -119.2277 178.9286 33.0328 0.0058 0.0019
Base 9 18 DCon1 0.0217 -85.2029 166.7724 23.6498 0.0054 0.0015
Base 9 18 DCon2 0.0257 -166.4206 238.6365 46.0954 0.0077 0.0025
Base 9 18 DCon3 0.0178 -135.1591 202.7744 38.745 0.0044 0.0021
Base 9 18 DCon4 0.0283 -127.64 202.732 34.0777 0.0087 0.0021
Base 9 18 DCon5 0.0087 -58.5329 107.232 17.5371 0.0014 0.0009
Base 9 18 DCon6 0.0192 -51.0137 107.1897 12.8698 0.0056 0.0009
Base 10 20 Dead -2.0451 -40.7349 54.9314 11.2724 -0.4478 -0.0303
Base 10 20 Live -2.1089 -43.9197 50.379 12.165 -0.4569 -0.0299
Base 10 20 SDL 0.3408 -5.6602 51.6734 1.621 0.1158 0.0108
Base 10 20 Wind 0.4286 -3.1429 0.5466 2.2333 0.1922 -0.0183
Base 10 20 SLS -3.3847 -93.4577 157.5304 27.2918 -0.5968 -0.0676
Base 10 20 Total DL -1.7044 -46.3951 106.6048 12.8935 -0.3321 -0.0195
Base 10 20 DStlS1 -2.3861 -64.9532 149.2467 18.0509 -0.4649 -0.0273
Base 10 20 DStlS2 -5.4195 -125.9457 208.5321 34.9362 -1.1296 -0.0712
Base 10 20 DStlS3 -3.7255 -102.7367 178.8513 29.8705 -0.6632 -0.0715
Base 10 20 DStlS4 -4.5828 -96.451 177.7581 25.4038 -1.0476 -0.035
Base 10 20 DStlS5 -1.1053 -44.8985 96.4909 13.8374 -0.1067 -0.0358
Base 10 20 DStlS6 -1.9626 -38.6128 95.3977 9.3708 -0.491 0.0007
Base 10 20 DStlD1 -1.7044 -46.3951 106.6048 12.8935 -0.3321 -0.0195
Base 10 20 DStlD2 -3.8133 -90.3148 156.9838 25.0585 -0.789 -0.0494
Base 10 20 DCon1 -2.3861 -64.9532 149.2467 18.0509 -0.4649 -0.0273
Base 10 20 DCon2 -5.4195 -125.9457 208.5321 34.9362 -1.1296 -0.0712
Base 10 20 DCon3 -3.7255 -102.7367 178.8513 29.8705 -0.6632 -0.0715
Base 10 20 DCon4 -4.5828 -96.451 177.7581 25.4038 -1.0476 -0.035
Base 10 20 DCon5 -1.1053 -44.8985 96.4909 13.8374 -0.1067 -0.0358

Page 76 of 80
Analysis Results 8/31/2018

Table 5.5 - Joint Reactions (continued)

Joint Unique Load FX FY FZ MX MY MZ

Story
Label Name Case/Combo kN kN kN kN-m kN-m kN-m
Base 10 20 DCon6 -1.9626 -38.6128 95.3977 9.3708 -0.491 0.0007
Base 11 22 Dead -2.3912 -2.0781 15.5724 0 0 0
Base 11 22 Live -2.5152 -2.1605 7.6093 0 0 0
Base 11 22 SDL -3.2195 -2.1806 34.2556 0 0 0
Base 11 22 Wind 0.2674 1.2778 2.0184 0 0 0
Base 11 22 SLS -7.8586 -5.1415 59.4557 0 0 0
Base 11 22 Total DL -5.6107 -4.2588 49.828 0 0 0
Base 11 22 DStlS1 -7.855 -5.9623 69.7592 0 0 0
Base 11 22 DStlS2 -10.7572 -8.5672 71.9685 0 0 0
Base 11 22 DStlS3 -8.9807 -5.9932 69.4213 0 0 0
Base 11 22 DStlS4 -9.5154 -8.5487 65.3844 0 0 0
Base 11 22 DStlS5 -4.7823 -2.5551 46.8636 0 0 0
Base 11 22 DStlS6 -5.317 -5.1106 42.8267 0 0 0
Base 11 22 DStlD1 -5.6107 -4.2588 49.828 0 0 0
Base 11 22 DStlD2 -8.1259 -6.4192 57.4373 0 0 0
Base 11 22 DCon1 -7.855 -5.9623 69.7592 0 0 0
Base 11 22 DCon2 -10.7572 -8.5672 71.9685 0 0 0
Base 11 22 DCon3 -8.9807 -5.9932 69.4213 0 0 0
Base 11 22 DCon4 -9.5154 -8.5487 65.3844 0 0 0
Base 11 22 DCon5 -4.7823 -2.5551 46.8636 0 0 0
Base 11 22 DCon6 -5.317 -5.1106 42.8267 0 0 0
Base 12 24 Dead -13.4016 0.5937 33.7656 0 0 0
Base 12 24 Live -15.333 0.6461 28.1855 0 0 0
Base 12 24 SDL -2.9018 -0.2002 35.3003 0 0 0
Base 12 24 Wind 0.57 0.2264 1.4222 0 0 0
Base 12 24 SLS -31.0664 1.266 98.6735 0 0 0
Base 12 24 Total DL -16.3034 0.3935 69.0658 0 0 0
Base 12 24 DStlS1 -22.8248 0.5509 96.6922 0 0 0
Base 12 24 DStlS2 -44.0969 1.5059 127.9758 0 0 0
Base 12 24 DStlS3 -34.327 1.3447 112.4867 0 0 0
Base 12 24 DStlS4 -35.4671 0.8919 109.6423 0 0 0
Base 12 24 DStlS5 -14.1031 0.5805 63.5815 0 0 0
Base 12 24 DStlS6 -15.2431 0.1278 60.7371 0 0 0
Base 12 24 DStlD1 -16.3034 0.3935 69.0658 0 0 0
Base 12 24 DStlD2 -31.6364 1.0396 97.2513 0 0 0
Base 12 24 DCon1 -22.8248 0.5509 96.6922 0 0 0
Base 12 24 DCon2 -44.0969 1.5059 127.9758 0 0 0
Base 12 24 DCon3 -34.327 1.3447 112.4867 0 0 0
Base 12 24 DCon4 -35.4671 0.8919 109.6423 0 0 0
Base 12 24 DCon5 -14.1031 0.5805 63.5815 0 0 0
Base 12 24 DCon6 -15.2431 0.1278 60.7371 0 0 0
Base 13 26 Dead -13.6353 -0.5899 33.6149 0 0 0
Base 13 26 Live -15.584 -0.6349 28.0116 0 0 0
Base 13 26 SDL -2.9394 0.2384 35.1912 0 0 0
Base 13 26 Wind -0.3502 0.2049 -1.1722 0 0 0

Page 77 of 80
Analysis Results 8/31/2018

Table 5.5 - Joint Reactions (continued)

Joint Unique Load FX FY FZ MX MY MZ

Story
Label Name Case/Combo kN kN kN kN-m kN-m kN-m
Base 13 26 SLS -32.5089 -0.7816 95.6455 0 0 0
Base 13 26 Total DL -16.5747 -0.3515 68.8061 0 0 0
Base 13 26 DStlS1 -23.2045 -0.4921 96.3285 0 0 0
Base 13 26 DStlS2 -44.8241 -1.4377 127.3859 0 0 0
Base 13 26 DStlS3 -35.8238 -0.8519 109.4067 0 0 0
Base 13 26 DStlS4 -35.1235 -1.2616 111.7511 0 0 0
Base 13 26 DStlS5 -15.2674 -0.1115 60.7533 0 0 0
Base 13 26 DStlS6 -14.5671 -0.5212 63.0976 0 0 0
Base 13 26 DStlD1 -16.5747 -0.3515 68.8061 0 0 0
Base 13 26 DStlD2 -32.1587 -0.9865 96.8177 0 0 0
Base 13 26 DCon1 -23.2045 -0.4921 96.3285 0 0 0
Base 13 26 DCon2 -44.8241 -1.4377 127.3859 0 0 0
Base 13 26 DCon3 -35.8238 -0.8519 109.4067 0 0 0
Base 13 26 DCon4 -35.1235 -1.2616 111.7511 0 0 0
Base 13 26 DCon5 -15.2674 -0.1115 60.7533 0 0 0
Base 13 26 DCon6 -14.5671 -0.5212 63.0976 0 0 0
Base 14 28 Dead 13.3999 0.594 33.7736 0 0 0
Base 14 28 Live 15.3306 0.6455 28.1906 0 0 0
Base 14 28 SDL 2.8922 -0.205 35.2877 0 0 0
Base 14 28 Wind -0.5775 0.2216 1.4478 0 0 0
Base 14 28 SLS 31.0452 1.2561 98.6998 0 0 0
Base 14 28 Total DL 16.2921 0.389 69.0614 0 0 0
Base 14 28 DStlS1 22.809 0.5446 96.6859 0 0 0
Base 14 28 DStlS2 44.0795 1.4995 127.9786 0 0 0
Base 14 28 DStlS3 34.3037 1.3339 112.512 0 0 0
Base 14 28 DStlS4 35.4586 0.8906 109.6165 0 0 0
Base 14 28 DStlS5 14.0854 0.5717 63.603 0 0 0
Base 14 28 DStlS6 15.2404 0.1285 60.7075 0 0 0
Base 14 28 DStlD1 16.2921 0.389 69.0614 0 0 0
Base 14 28 DStlD2 31.6227 1.0345 97.252 0 0 0
Base 14 28 DCon1 22.809 0.5446 96.6859 0 0 0
Base 14 28 DCon2 44.0795 1.4995 127.9786 0 0 0
Base 14 28 DCon3 34.3037 1.3339 112.512 0 0 0
Base 14 28 DCon4 35.4586 0.8906 109.6165 0 0 0
Base 14 28 DCon5 14.0854 0.5717 63.603 0 0 0
Base 14 28 DCon6 15.2404 0.1285 60.7075 0 0 0
Base 15 30 Dead 13.6339 -0.5901 33.6237 0 0 0
Base 15 30 Live 15.5825 -0.635 28.0155 0 0 0
Base 15 30 SDL 2.9332 0.2391 35.1654 0 0 0
Base 15 30 Wind 0.364 0.2 -1.2171 0 0 0
Base 15 30 SLS 32.5135 -0.7861 95.5876 0 0 0
Base 15 30 Total DL 16.5671 -0.351 68.7891 0 0 0
Base 15 30 DStlS1 23.1939 -0.4915 96.3047 0 0 0
Base 15 30 DStlS2 44.8125 -1.4373 127.3718 0 0 0
Base 15 30 DStlS3 35.8269 -0.8563 109.3454 0 0 0

Page 78 of 80
Analysis Results 8/31/2018

Table 5.5 - Joint Reactions (continued)

Joint Unique Load FX FY FZ MX MY MZ

Story
Label Name Case/Combo kN kN kN kN-m kN-m kN-m
Base 15 30 DStlS4 35.099 -1.2562 111.7795 0 0 0
Base 15 30 DStlS5 15.2744 -0.116 60.6931 0 0 0
Base 15 30 DStlS6 14.5464 -0.5159 63.1272 0 0 0
Base 15 30 DStlD1 16.5671 -0.351 68.7891 0 0 0
Base 15 30 DStlD2 32.1496 -0.986 96.8046 0 0 0
Base 15 30 DCon1 23.1939 -0.4915 96.3047 0 0 0
Base 15 30 DCon2 44.8125 -1.4373 127.3718 0 0 0
Base 15 30 DCon3 35.8269 -0.8563 109.3454 0 0 0
Base 15 30 DCon4 35.099 -1.2562 111.7795 0 0 0
Base 15 30 DCon5 15.2744 -0.116 60.6931 0 0 0
Base 15 30 DCon6 14.5464 -0.5159 63.1272 0 0 0

5.4 Modal Results

Table 5.6 - Modal Periods and Frequencies

Circular
Period Frequency Eigenvalue
Case Mode Frequency
sec cyc/sec rad²/sec²
rad/sec
Modal 1 0.136 7.338 46.1047 2125.6446
Modal 2 0.115 8.671 54.48 2968.0658
Modal 3 0.113 8.888 55.8443 3118.5885
Modal 4 0.102 9.819 61.6923 3805.944
Modal 5 0.098 10.253 64.4243 4150.4962
Modal 6 0.097 10.268 64.5179 4162.5598
Modal 7 0.091 11.015 69.2096 4789.9674
Modal 8 0.08 12.495 78.5059 6163.17
Modal 9 0.077 12.968 81.4812 6639.1875
Modal 10 0.076 13.079 82.1747 6752.6853
Modal 11 0.075 13.27 83.3784 6951.9511
Modal 12 0.072 13.857 87.0654 7580.3869

Table 5.7 - Modal Participating Mass Ratios (Part 1 of 2)

Period Sum Sum

Case Mode UX UY UZ Sum UZ
sec UX UY
Modal 1 0.136 0.1166 0 0 0.1166 0 0
Modal 2 0.115 0 0.2441 0 0.1166 0.2441 0
Modal 3 0.113 1.15E-06 3.785E-05 0 0.1166 0.2442 0
Modal 4 0.102 0.1672 0 0 0.2838 0.2442 0
Modal 5 0.098 3.09E-05 0.0197 0 0.2838 0.2638 0
Modal 6 0.097 0.0006 0.0007 0 0.2845 0.2645 0
Modal 7 0.091 0 1.151E-06 0 0.2845 0.2645 0
Modal 8 0.08 5.415E-06 7.887E-06 0 0.2845 0.2645 0
Modal 9 0.077 2.486E-05 0.0004 0 0.2845 0.2649 0
Modal 10 0.076 1.76E-05 0.0004 0 0.2845 0.2653 0
Modal 11 0.075 0.0028 2.941E-05 0 0.2873 0.2653 0
Modal 12 0.072 0.0014 7.501E-06 0 0.2887 0.2653 0

Page 79 of 80
Analysis Results 8/31/2018

Table 5.7 - Modal Participating Mass Ratios (Part 2 of 2)

Sum Sum
Case Mode RX RY RZ Sum RZ
RX RY
Modal 1 0 0.6451 1.059E-05 0 0.6451 1.059E-05
Modal 2 0.6843 0 3.948E-05 0.6843 0.6451 0.0001
Modal 3 0.0001 5.495E-07 0.2525 0.6844 0.6451 0.2525
Modal 4 0 0.1311 0 0.6844 0.7762 0.2525
Modal 5 0.0329 2.574E-05 0.0004 0.7173 0.7762 0.2529
Modal 6 0.0012 0.0005 0.0101 0.7184 0.7767 0.263
Modal 7 1.239E-06 0 0.0551 0.7184 0.7767 0.318
Modal 8 6.072E-07 0 0 0.7184 0.7767 0.318
Modal 9 3.799E-05 1.656E-06 4.743E-05 0.7185 0.7767 0.3181
Modal 10 0.0001 4.719E-06 0.0002 0.7186 0.7767 0.3183
Modal 11 2.241E-06 0.0005 2.676E-05 0.7186 0.7772 0.3183
Modal 12 0 0.0001 0.0032 0.7186 0.7774 0.3215

Table 5.8 - Modal Load Participation Ratios

Static Dynamic
Case Item Type Item
% %
Modal Acceleration UX 74.62 28.87
Modal Acceleration UY 71.54 26.53
Modal Acceleration UZ 0 0

Table 5.9 - Modal Direction Factors

Period
Case Mode UX UY UZ RZ
sec
Modal 1 0.136 1 0 0 0
Modal 2 0.115 0 1 0 0
Modal 3 0.113 0 0.002 0 0.998
Modal 4 0.102 0.999 0 0 0.001
Modal 5 0.098 0.001 0.931 0 0.068
Modal 6 0.097 0.014 0.019 0 0.967
Modal 7 0.091 0 0 0 1
Modal 8 0.08 0.205 0.784 0 0.011
Modal 9 0.077 0.046 0.869 0 0.085
Modal 10 0.076 0.022 0.77 0 0.208
Modal 11 0.075 0.855 0.015 0 0.13
Modal 12 0.072 0.185 0.003 0 0.812

Page 80 of 80
ETABS 2016 16.2.1 License #*1MRY9PW5NFB4MRZ

ETABS 2016 Concrete Frame Design

ACI 318-11 Column Section Design

Column Element Details (Summary)

Level Element Unique Name Section ID Combo ID Station Loc Length (mm) LLRF Type
1F C9 48 C30x30 DCon2 0 3000 1 Sway Special

Section Properties

b (mm) h (mm) dc (mm) Cover (Torsion) (mm)

300 300 48 17.3

Material Properties

E c (MPa) f' c (MPa) Lt.Wt Factor (Unitless) f y (MPa) f ys (MPa)

24855.58 25 1 390 390

Design Code Parameters

ΦT Φ CTied Φ CSpiral Φ Vns Φ Vs Φ Vjoint Ω0

0.9 0.65 0.75 0.75 0.6 0.85 2

Axial Force and Biaxial Moment Design For P u , M u2 , M u3

Design P u Design M u2 Design M u3 Minimum M 2 Minimum M 3 Rebar % Capacity Ratio

kN kN-m kN-m kN-m kN-m % Unitless
29.3321 35.5734 0.711 0.711 0.711 1.58 0.571

Axial Force and Biaxial Moment Factors

C m Factor δ ns Factor δ s Factor K Factor Effective Length

Unitless Unitless Unitless Unitless mm
Major Bend(M3) 0.459088 1 1 1 2900
Minor Bend(M2) 0.599885 1 1 1 2900

2.EDB Page 1 of 2 8/31/2018

ETABS 2016 16.2.1 License #*1MRY9PW5NFB4MRZ

Shear Design for V u2 , V u3

Shear V u Shear ΦV c Shear ΦV s Shear ΦV p Rebar A v /s

kN kN kN kN mm²/m
Major, V u2 0.0245 48.1937 0 0 0
Minor, V u3 12.2702 48.1937 0 0 0

Joint Shear Check/Design

Joint Shear Shear Shear Shear Joint Shear

Force V u,Top V u,Tot ΦV c Area Ratio
kN kN kN kN cm² Unitless
Major Shear, V u2 N/A N/A N/A N/A N/A N/A
Minor Shear, V u3 N/A N/A N/A N/A N/A N/A

(6/5) Beam/Column Capacity Ratio

Major Ratio Minor Ratio

N/A N/A

Notes:

N/A: Not Applicable

N/C: Not Calculated

N/N: Not Needed

2.EDB Page 2 of 2 8/31/2018

ETABS 2016 16.2.1 License #*1MRY9PW5NFB4MRZ

ETABS 2016 Concrete Frame Design

ACI 318-11 Column Section Design

Column Element Details (Flexural Details)

Level Element Unique Name Section ID Combo ID Station Loc Length (mm) LLRF Type
1F C3 43 C30x30 DCon2 0 3000 1 Sway Special

Section Properties

b (mm) h (mm) dc (mm) Cover (Torsion) (mm)

300 300 48 17.3

Material Properties

E c (MPa) f' c (MPa) Lt.Wt Factor (Unitless) f y (MPa) f ys (MPa)

24855.58 25 1 390 390

Design Code Parameters

ΦT Φ CTied Φ CSpiral Φ Vns Φ Vs Φ Vjoint Ω0

0.9 0.65 0.75 0.75 0.6 0.85 2

Axial Force and Biaxial Moment Design For P u , M u2 , M u3

Design P u Design M u2 Design M u3 Minimum M 2 Minimum M 3 Rebar % Capacity Ratio

kN kN-m kN-m kN-m kN-m % Unitless
29.3236 -35.5894 0.7108 0.7108 0.7108 1.58 0.571

Factored & Minimum Biaxial Moments

NonSway M ns Sway M s Factored M u Minimum M min Minimum Eccentricity

kN-m kN-m kN-m kN-m mm
Major Bending(M u3) 0.0559 0 0.0559 0.7108 24.2
Minor Bending(M u2) -35.5894 0 -35.5894 0.7108 24.2

2.EDB Page 1 of 2 8/31/2018

ETABS 2016 16.2.1 License #*1MRY9PW5NFB4MRZ

Axial Force and Biaxial Moment Factors

C m Factor δ ns Factor δ s Factor K Factor Effective Length

Unitless Unitless Unitless Unitless mm
Major Bend(M3) 0.465284 1 1 1 2900
Minor Bend(M2) 0.599935 1 1 1 2900

2.EDB Page 2 of 2 8/31/2018

ETABS 2016 16.2.1 License #*1MRY9PW5NFB4MRZ

ETABS 2016 Concrete Frame Design

ACI 318-11 Column Section Design

Column Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type

1F C3 43 C30x30 3000 1 Sway Special

Section Properties

b (mm) h (mm) dc (mm) Cover (Torsion) (mm)

300 300 48 17.3

Material Properties

E c (MPa) f' c (MPa) Lt.Wt Factor (Unitless) f y (MPa) f ys (MPa)

24855.58 25 1 390 390

Design Code Parameters

ΦT Φ CTied Φ CSpiral Φ Vns Φ Vs Φ Vjoint

0.9 0.65 0.75 0.85 0.6 0.85

Longitudinal Check for P u - M u2 - M u3 Interaction

Column End Rebar Area Rebar D/C Ratio

mm² %
Top 1420 1.58 0.017
Bottom 1420 1.58 0.571

Design Axial Force & Biaxial Moment for P u - M u2 - M u3 Interaction

Column End Design P u Design M u2 Design M u3 Station Loc Controlling Combo

kN kN-m kN-m mm
kN kN-m kN-m mm
Top 21.8068 0.5286 -0.0188 2900 DCon2
Bottom 29.3236 -35.5894 0.7108 0 DCon2

Shear Reinforcement for Major Shear, V u2

Column End Rebar A v /s Design V u2 Station Loc Controlling Combo

mm²/m kN mm
Top 0 0.0258 2900 DCon2
Bottom 0 0.0258 0 DCon2

Shear Reinforcement for Minor Shear, V u3

Column End Rebar A v /s Design V u3 Station Loc Controlling Combo

mm²/m kN mm
Top 0 12.2742 2900 DCon2
Bottom 0 12.2742 0 DCon2

2.EDB Page 1 of 1 8/31/2018

ETABS 2016 16.2.1 License #*1MRY9PW5NFB4MRZ

ETABS 2016 Concrete Frame Design

ACI 318-11 Beam Section Design

Beam Element Details (Summary)

Level Element Unique Name Section ID Combo ID Station Loc Length (mm) LLRF Type
GF B24 39 B25x50 DCon2 3750 7500 1 Sway Special

Section Properties

b (mm) h (mm) b f (mm) d s (mm) d ct (mm) d cb (mm)

250 500 250 0 90 90

Material Properties

E c (MPa) f' c (MPa) Lt.Wt Factor (Unitless) f y (MPa) f ys (MPa)

24855.58 25 1 390 390

Design Code Parameters

ΦT Φ CTied Φ CSpiral Φ Vns Φ Vs Φ Vjoint

0.9 0.65 0.75 0.75 0.6 0.85

Design Moment and Flexural Reinforcement for Moment, M u3

Design Design -Moment +Moment Minimum Required

-Moment +Moment Rebar Rebar Rebar Rebar
kN-m kN-m mm² mm² mm² mm²
Top (+2 Axis) -30.7549 149 0 198 198
Bottom (-2 Axis) 158.5423 0 1181 362 1181

Shear Force and Reinforcement for Shear, V u2

Shear V u2 Shear ΦV c Shear ΦV s Shear V p Rebar A v /S

kN kN kN kN mm²/m
13.8829 63.8329 0 0 0

2.EDB Page 1 of 2 8/31/2018

ETABS 2016 16.2.1 License #*1MRY9PW5NFB4MRZ

Torsion Force and Torsion Reinforcement for Torsion, T u

Φ*T u Tcr Area A o Perimeter, p h Rebar A t /s Rebar A l

kN-m kN-m cm² mm mm²/m mm²
0.001 3.5499 562.9 1144.4 0 0

2.EDB Page 2 of 2 8/31/2018

ETABS 2016 16.2.1 License #*1MRY9PW5NFB4MRZ

ETABS 2016 Concrete Frame Design

ACI 318-11 Beam Section Design

Beam Element Details (Flexural Details)

Level Element Unique Name Section ID Combo ID Station Loc Length (mm) LLRF Type
GF B24 39 B25x50 DCon2 3750 7500 1 Sway Special

Section Properties

b (mm) h (mm) b f (mm) d s (mm) d ct (mm) d cb (mm)

250 500 250 0 90 90

Material Properties

E c (MPa) f' c (MPa) Lt.Wt Factor (Unitless) f y (MPa) f ys (MPa)

24855.58 25 1 390 390

Design Code Parameters

ΦT Φ CTied Φ CSpiral Φ Vns Φ Vs Φ Vjoint

0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Moment, M u3

Required +Moment -Moment Minimum

Rebar Rebar Rebar Rebar
mm² mm² mm² mm²
Top (+2 Axis) 198 0 149 198
Bottom (-2 Axis) 1181 1181 0 362

Design Moments, M u3

Design Design
+Moment -Moment
kN-m kN-m
158.5423 -30.7549

2.EDB Page 1 of 1 8/31/2018

ETABS 2016 16.2.1 License #*1MRY9PW5NFB4MRZ

ETABS 2016 Concrete Frame Design

ACI 318-11 Beam Section Design

Beam Element Details (Shear Details)

Level Element Unique Name Section ID Combo ID Station Loc Length (mm) LLRF Type
GF B24 39 B25x50 DCon2 3750 7500 1 Sway Special

Section Properties

b (mm) h (mm) b f (mm) d s (mm) d ct (mm) d cb (mm)

250 500 250 0 90 90

Material Properties

E c (MPa) f' c (MPa) Lt.Wt Factor (Unitless) f y (MPa) f ys (MPa)

24855.58 25 1 390 390

Design Code Parameters

ΦT Φ CTied Φ CSpiral Φ Vns Φ Vs Φ Vjoint

0.9 0.65 0.75 0.75 0.6 0.85

Shear/Torsion Design for V u2 and T u

Rbar Rbar Rbar Design Design Design Design

A vs A t /S Al V u2 Tu M u3 Pu
mm²/m mm²/m mm² kN kN-m kN-m kN
0 0 0 13.8829 0.001 158.5423 0

Design Forces

Design Design
V u2 M u3
kN kN-m
13.8829 129.3281

2.EDB Page 1 of 2 8/31/2018

ETABS 2016 16.2.1 License #*1MRY9PW5NFB4MRZ

Design Basis

Design Conc.Area Area Tensn.Reinf Strength Strength LtWt.Reduc

V u2 Ac Ag A-st f ys f cs Factor
kN cm² cm² mm² MPa MPa Unitless
13.8829 1025 1250 1181 390 25 1

Shear Rebar Design

Stress Conc.Capacity Uppr.Limit Conc.Capacity Uppr.Limit RebarArea Shear Shear Shear

v vc v max Φv c Φv max A v /s ΦV c ΦV s ΦV n
MPa MPa MPa MPa MPa mm²/m kN kN kN
0.14 0.83 4.15 0.62 3.11 0 63.8329 0 63.8329

Torsion Capacity

Torsion Critical Conc.Area Conc.Area Conc.Area Perimeter Perimeter

Tu ΦT cr A cp A oh Ao P cp Ph
kN-m kN-m cm² cm² cm² mm mm
0.001 3.5499 1250 662.3 562.9 1500 1144.4

2.EDB Page 2 of 2 8/31/2018

ETABS 2016 16.2.1 License #*1MRY9PW5NFB4MRZ

ETABS 2016 Concrete Frame Design

ACI 318-11 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type

GF B24 39 B25x50 7500 1 Sway Special

Section Properties

b (mm) h (mm) b f (mm) d s (mm) d ct (mm) d cb (mm)

250 500 250 0 90 90

Material Properties

E c (MPa) f' c (MPa) Lt.Wt Factor (Unitless) f y (MPa) f ys (MPa)

24855.58 25 1 390 390

Design Code Parameters

ΦT Φ CTied Φ CSpiral Φ Vns Φ Vs Φ Vjoint

0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, M u3

End-I End-I Middle Middle End-J End-J

Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 822 0.66 198 0.16 822 0.66
Bot (-2 Axis) 548 0.44 1181 0.94 548 0.44

Flexural Design Moment, M u3

End-I End-I Middle Middle End-J End-J

Design M u Station Loc Design M u Station Loc Design M u Station Loc
kN-m mm kN-m mm kN-m mm
Top (+2 Axis) -123.0197 150 -30.7549 5000 -122.9849 7350
Combo DCon2 DCon2 DCon2
Bot (-2 Axis) 84.5185 1666.7 158.5423 3750 84.5244 5833.3
Combo DCon2 DCon2 DCon2

Shear Reinforcement for Major Shear, V u2

End-I Middle End-J

Rebar A v /s Rebar A v /s Rebar A v /s
mm²/m mm²/m mm²/m
484.2 220.99 484.09

2.EDB Page 1 of 2 8/31/2018

ETABS 2016 16.2.1 License #*1MRY9PW5NFB4MRZ

Design Shear Force for Major Shear, V u2

End-I End-I Middle Middle End-J End-J

Design V u Station Loc Design V u Station Loc Design V u Station Loc
kN mm kN mm kN mm
121.9002 150 0.0631 5416.7 121.8877 7350
DCon2 DCon4 DCon2

Torsion Reinforcement

Shear Longitudinal
Rebar A t /s Rebar A l
mm²/m mm²
0 0

Design Torsion Force

Design T u Station Loc Design T u Station Loc

kN-m mm kN-m mm
0.0145 7350 0.0145 7350
DCon4 DCon4

2.EDB Page 2 of 2 8/31/2018

ETABS 2016 16.2.1 License #*1MRY9PW5NFB4MRZ

ETABS 2016 Steel Frame Design

AISC 360-10 Steel Section Check (Strength Summary)

Element Details

Level Element Unique Name Location (mm) Combo Element Type Section Classification
Roof D227 366 0 DStlS2 Special Moment Frame U&L chord Slender

LLRF and Demand/Capacity Ratio

L (mm) LLRF Stress Ratio Limit

978.1 1 0.95

Analysis and Design Parameters

Provision Analysis 2nd Order Reduction

LRFD Direct Analysis General 2nd Order Tau-b Fixed

Stiffness Reduction Factors

αP r /P y αP r /P e τb EA factor EI factor
0.184 0.393 1 0.8 0.8

Design Code Parameters

Φb Φc Φ TY Φ TF ΦV Φ V-RI Φ VT
0.9 0.9 0.9 0.75 0.9 1 1

Section Properties

A (cm²) J (cm ) I 33 (cm ) I 22 (cm ) A v3 (cm²) A v2 (cm²)

3.5 37.8 47.9 16.4 1.1 2.3

Design Properties

S 33 (cm³) S 22 (cm³) Z 33 (cm³) Z 22 (cm³) r 33 (mm) r 22 (mm) C w (cm )

9.6 6.6 11.6 7.2 36.8 21.5

Material Properties

E (MPa) f y (MPa) Ry α
199947.98 250 1.489 NA

HSS Section Parameters

HSS Welding Reduce HSS Thickness?

ERW No

Stress Check forces and Moments

Location (mm) P u (kN) M u33 (kN-m) M u22 (kN-m) V u2 (kN) V u3 (kN) T u (kN-m)
0 -16.3287 0.3903 -0.003 0.1881 -0.0023 -0.0001

2.EDB Page 1 of 2 8/31/2018

ETABS 2016 16.2.1 License #*1MRY9PW5NFB4MRZ

Axial Force & Biaxial Moment Design Factors (H1-1a)

L Factor K1 K2 B1 B2 Cm
Major Bending 1 1 1 1 1 1
Minor Bending 2.857 1 1 1 1 1

Parameters for Lateral Torsion Buckling

L ltb K ltb Cb
2.857 1 1.834

Demand/Capacity (D/C) Ratio Eqn.(H1-1a)

(P r /P c ) + (8/9)(M r33 /M c33 ) + (8/9)(M r22

D/C Ratio =
/M c22 )
0.709 = 0.54 + 0.166 + 0.003

Axial Force and Capacities

P u Force (kN) ϕP nc Capacity (kN) ϕP nt Capacity (kN)

16.3287 30.2135 79.704

Moments and Capacities

M u Moment (kN-m) ϕM n (kN-m) ϕM n No LTB (kN-m) ϕM n Cb=1 (kN-m)

Major Bending 0.3903 2.09 2.09 2.6198
Minor Bending 0.003 0.9525

Torsion Moment and Capacities

T u Moment (kN-m) T n Capacity (kN-m) ϕT n Capacity (kN-m)

-0.0001 1.4778 1.33

Shear Design

V u Force (kN) ϕV n Capacity (kN) Stress Ratio

Major Shear 0.1881 27.0453 0.007
Minor Shear 0.0023 15.0336 1.538E-04

End Reaction Axial Forces

Left End Reaction (kN) Load Combo Right End Reaction (kN) Load Combo
-16.3287 DStlS6 -15.4680 DStlS6

2.EDB Page 2 of 2 8/31/2018

ETABS 2016 16.2.1 License #*1MRY9PW5NFB4MRZ

ETABS 2016 Steel Frame Design

AISC 360-10 Steel Section Check (Strength Envelope)

Element Details

Level Element Unique Name Section Combo Location Frame Type Classification
Roof D227 366 U&L chord DStlS2 0 Special Moment Frame Slender

LLRF and Demand/Capacity Ratio

L (mm) LLRF Stress Ratio Limit

978.1 1 0.95

Analysis and Design Parameters

Provision Analysis 2nd Order Reduction

LRFD Direct Analysis General 2nd Order Tau-b Fixed

Stiffness Reduction Factors

αP r /P y αP r /P e τb EA factor EI factor
0.184 0.393 1 0.8 0.8

Design Code Parameters

Φb Φb Φ TY Φ TF ΦV Φ V-RI Φ VT
0.9 0.9 0.9 0.75 0.9 1 1

Section Properties

A (cm²) J (cm ) I 33 (cm ) I 22 (cm ) A v3 (cm²) A v2 (cm²)

3.5 37.8 47.9 16.4 1.1 2.3

Design Properties

S 33 (cm³) S 22 (cm³) Z 33 (cm³) Z 22 (cm³) r 33 (mm) r 22 (mm)

9.6 6.6 11.6 36.8 21.5

Material Properties

E (MPa) f y (MPa) Ry α
199947.98 250 1.489 NA

HSS Section Parameters

HSS Welding Reduce HSS Thickness?

ERW No

Stress Check forces and Moments

Location (mm) P u (kN) M u33 (kN-m) M u22 (kN-m) V u2 (kN) V u3 (kN) T u (kN-m)
0 -16.3287 0.3903 -0.003 0.1881 -0.0023 -0.0001

2.EDB Page 1 of 2 8/31/2018

ETABS 2016 16.2.1 License #*1MRY9PW5NFB4MRZ

Axial Force & Biaxial Moment Design Factors (H1-1a)

L Factor K1 K2 B1 B2 Cm
Major Bending 1 1 1 1 1 1
Minor Bending 2.857 1 1 1 1 1

Parameters for Lateral Torsion Buckling

L ltb K ltb Cb
2.857 1 1.834

Demand/Capacity (D/C) Ratio

(P r /P c ) + (8/9)(M r33 /M c33 ) + (8/9)(M r22

D/C Ratio =
/M c22 )
0.709 = 0.54 + 0.166 + 0.003

Axial Force and Capacities

P u Force (kN) ϕP nc Capacity (kN) ϕP nt Capacity (kN)

16.3287 30.2135 79.704

Moments and Capacities

M u Moment (kN-m) ϕM n Capacity (kN-m) ϕM n No LTB (kN-m) ϕM n Cb=1 (kN-m)

Major Bending 0.3903 2.09 2.09 2.6198
Minor Bending 0.003 0.9525

Torsion Moment and Capacities

T u Moment (kN-m) T n Capacity (kN-m) ϕT n Capacity (kN-m)

-0.0001 1.4778 1.33

Shear Design

V u Force (kN) ϕV n Capacity (kN) Stress Ratio

Major Shear 1.0699 27.0453 0.04
Minor Shear 0.0023 15.0336 1.538E-04

End Reaction Axial Forces

Left End Reaction (kN) Load Combo Right End Reaction (kN) Load Combo
-16.3287 DStlS6 -15.4680 DStlS6

2.EDB Page 2 of 2 8/31/2018

ETABS 2016 16.2.1 License #*1MRY9PW5NFB4MRZ

ETABS 2016 Steel Frame Design

AISC 360-10 Steel Section Check (Strength Summary)

Element Details

Level Element Unique Name Location (mm) Combo Element Type Section Classification
Roof B107 472 25 DStlS4 Special Moment Frame W&P chord Slender

LLRF and Demand/Capacity Ratio

L (mm) LLRF Stress Ratio Limit

1000.0 1 0.95

Analysis and Design Parameters

Provision Analysis 2nd Order Reduction

LRFD Direct Analysis General 2nd Order Tau-b Fixed

Stiffness Reduction Factors

αP r /P y αP r /P e τb EA factor EI factor
0.178 0.494 1 0.8 0.8

Design Code Parameters

Φb Φc Φ TY Φ TF ΦV Φ V-RI Φ VT
0.9 0.9 0.9 0.75 0.9 1 1

Section Properties

A (cm²) J (cm ) I 33 (cm ) I 22 (cm ) A v3 (cm²) A v2 (cm²)

2.3 13.9 9.3 9.3 1.1 1.1

Design Properties

S 33 (cm³) S 22 (cm³) Z 33 (cm³) Z 22 (cm³) r 33 (mm) r 22 (mm) C w (cm )

3.7 3.7 4.3 4.3 19.9 19.9

Material Properties

E (MPa) f y (MPa) Ry α
199947.98 250 1.489 NA

HSS Section Parameters

HSS Welding Reduce HSS Thickness?

ERW No

Stress Check forces and Moments

Location (mm) P u (kN) M u33 (kN-m) M u22 (kN-m) V u2 (kN) V u3 (kN) T u (kN-m)
25 -10.4262 -0.0527 0.0288 -0.1248 0.0484 -0.0017

2.EDB Page 1 of 2 8/31/2018

ETABS 2016 16.2.1 License #*1MRY9PW5NFB4MRZ

Axial Force & Biaxial Moment Design Factors (H1-1a)

L Factor K1 K2 B1 B2 Cm
Major Bending 0.95 1 1 1 1 1
Minor Bending 2.95 1 1 1 1 1

Parameters for Lateral Torsion Buckling

L ltb K ltb Cb
2.95 1 2.134

Demand/Capacity (D/C) Ratio Eqn.(H1-1a)

(P r /P c ) + (8/9)(M r33 /M c33 ) + (8/9)(M r22

D/C Ratio =
/M c22 )
0.713 = 0.626 + 0.056 + 0.031

Axial Force and Capacities

P u Force (kN) ϕP nc Capacity (kN) ϕP nt Capacity (kN)

10.4262 16.6505 52.704

Moments and Capacities

M u Moment (kN-m) ϕM n (kN-m) ϕM n No LTB (kN-m) ϕM n Cb=1 (kN-m)

Major Bending 0.0527 0.8361 0.8361 0.9647
Minor Bending 0.0288 0.8361

Torsion Moment and Capacities

T u Moment (kN-m) T n Capacity (kN-m) ϕT n Capacity (kN-m)

-0.0017 0.8563 0.7707

Shear Design

V u Force (kN) ϕV n Capacity (kN) Stress Ratio

Major Shear 0.1248 15.0336 0.008
Minor Shear 0.0484 15.0336 0.003

End Reaction Major Shear Forces

Left End Reaction (kN) Load Combo Right End Reaction (kN) Load Combo
0.136 DStlS6 0.1154 DStlS6

2.EDB Page 2 of 2 8/31/2018

ETABS 2016 16.2.1 License #*1MRY9PW5NFB4MRZ

ETABS 2016 Steel Frame Design

AISC 360-10 Steel Section Check (Strength Envelope)

Element Details

Level Element Unique Name Section Combo Location Frame Type Classification
Roof B107 472 W&P chord DStlS4 25 Special Moment Frame Slender

LLRF and Demand/Capacity Ratio

L (mm) LLRF Stress Ratio Limit

1000.0 1 0.95

Analysis and Design Parameters

Provision Analysis 2nd Order Reduction

LRFD Direct Analysis General 2nd Order Tau-b Fixed

Stiffness Reduction Factors

αP r /P y αP r /P e τb EA factor EI factor
0.178 0.494 1 0.8 0.8

Design Code Parameters

Φb Φb Φ TY Φ TF ΦV Φ V-RI Φ VT
0.9 0.9 0.9 0.75 0.9 1 1

Section Properties

A (cm²) J (cm ) I 33 (cm ) I 22 (cm ) A v3 (cm²) A v2 (cm²)

2.3 13.9 9.3 9.3 1.1 1.1

Design Properties

S 33 (cm³) S 22 (cm³) Z 33 (cm³) Z 22 (cm³) r 33 (mm) r 22 (mm)

3.7 3.7 4.3 19.9 19.9

Material Properties

E (MPa) f y (MPa) Ry α
199947.98 250 1.489 NA

HSS Section Parameters

HSS Welding Reduce HSS Thickness?

ERW No

Stress Check forces and Moments

Location (mm) P u (kN) M u33 (kN-m) M u22 (kN-m) V u2 (kN) V u3 (kN) T u (kN-m)
25 -10.4262 -0.0527 0.0288 -0.1248 0.0484 -0.0017

2.EDB Page 1 of 2 8/31/2018

ETABS 2016 16.2.1 License #*1MRY9PW5NFB4MRZ

Axial Force & Biaxial Moment Design Factors (H1-1a)

L Factor K1 K2 B1 B2 Cm
Major Bending 0.95 1 1 1 1 1
Minor Bending 2.95 1 1 1 1 1

Parameters for Lateral Torsion Buckling

L ltb K ltb Cb
2.95 1 2.134

Demand/Capacity (D/C) Ratio

(P r /P c ) + (8/9)(M r33 /M c33 ) + (8/9)(M r22

D/C Ratio =
/M c22 )
0.713 = 0.626 + 0.056 + 0.031

Axial Force and Capacities

P u Force (kN) ϕP nc Capacity (kN) ϕP nt Capacity (kN)

10.4262 16.6505 52.704

Moments and Capacities

M u Moment (kN-m) ϕM n Capacity (kN-m) ϕM n No LTB (kN-m) ϕM n Cb=1 (kN-m)

Major Bending 0.0527 0.8361 0.8361 0.9647
Minor Bending 0.0288 0.8361

Torsion Moment and Capacities

T u Moment (kN-m) T n Capacity (kN-m) ϕT n Capacity (kN-m)

-0.0017 0.8563 0.7707

Shear Design

V u Force (kN) ϕV n Capacity (kN) Stress Ratio

Major Shear 0.136 15.0336 0.009
Minor Shear 0.0476 15.0336 0.003

End Reaction Major Shear Forces

Left End Reaction (kN) Load Combo Right End Reaction (kN) Load Combo
0.136 DStlS6 0.1154 DStlS6

2.EDB Page 2 of 2 8/31/2018

 FOUNDATION CALCULATION SHEET

One-Stop Solution for Foundation

TITLE DESCRIPTION
PROJECT/JOB NO. 001
PROJECT/JOB NAME Apartment
CLIENT NAME xx
SITE NAME xx
DOCUMENT NO.
REFERENCE NO.
STRUCTURE NAME The Resident
LOAD COMBINATION GROUP NAME
REV DATE DESCRIPTION PREP'D CHK'D APPR'D APPR'D

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 1

FOUNDATION LISTS
Group Name No. Description No. Description
F1 1 F1
F2 2 F2

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 2

CONTENTS

1. GENERAL
1.1 CODE & STANDARD
1.2 MATERIALS & UNIT WEIGHT
1.3 SUBSOIL CONDITION & SAFETY FACTORS
1.4 LOAD COMBINATION

2. DRAWING
2.1 LOCATION PLAN & DETAIL SKETCH

3. FOUNDATION DATA
3.1 FOOTING AND SECTION DATA
3.2 PIER DATA
3.3 LOAD CASE
3.4 LOAD COMBINATION

4. CHECK OF STABILITY
4.1 CHECK OF SLIDING
4.2 CHECK OF OVERTURNING MOMENT
4.3 CHECK OF CONTACT PRESSURE

5. DESIGN OF FOOTING
5.1 DESIGN MOMENT AND SHEAR FORCE
5.2 REQUIRED REINFORCEMENT
5.3 ONE WAY SHEAR FORCE
5.4 TWO WAY SHEAR FORCE

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 3

1. GENERAL
1.1 CODE & STANDARD
Items Description
Design Code American Concrete Institute (ACI 318) [SI]
Horizontal Force for Wind AMERICAN SOCIETY OF CIVIL ENGINEERS [ASCE 7-05]
Horizontal Force for Seismic AMERICAN SOCIETY CIVIL ENGINEERS [ASCE 7-05]
Unit System Input : SI, Output : SI, Calculation Unit : SI

1.2 MATERIALS & UNIT WEIGHT

Items Value
2
Concrete (f'c : compressive strength) 28.000 N/mm
2
Lean Concrete (Lf'c : compressive strength) 0.000 N/mm
2
Reinforcement (#6 ~ #18 , yield strength) 390.000 N/mm
2
Reinforcement (#20 ~ , yield strength) 390.000 N/mm
3
Rs (Soil unit weight) 18.000 kN/m
3
Rc (Concrete unit weight) 24.000 kN/m
2
Es (Steel Modulus of Elasticity) 200.000 kN/mm
2
Ec (Concrete Modulus of Elasticity) 26.000 kN/mm

- Soil Capacity
Items Value
Soil Name Unit-01
Footing List F1, F2
2
Qa (Soil Bearing Capacity) 81 kN/m
Buoyancy Not Consider
WL (Water Label from the EL = 0) 0 mm
FD (Frost Depth from the EL = 0) 0 mm
Internal Friction Angle 0
Passive Soil Pressure Not Consider
2
Cu (Undrained cohesion) Clay , 0 kN/m

1.3 SUBSOIL CONDITION & SAFETY FACTORS

Items Description
Allowable Increase of Soil (Wind) 0%
Allowable Increase of Soil (Seismic) 0%
Allowable Increase of Soil (Test) 0%
Safety factor against overturning for OVM1(FO1) 1.5
Safety factor against overturning for OVM2(FO2) 1.5
Safety factor against overturning for OVM3(FO3) 1.5
Safety factor against overturning for OVM4(FO4) 1.9

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 4

Safety factor against sliding for the SL1(FS1) 1.5

Safety factor against sliding for the SL2(FS2) 1.8
Safety factor against sliding for the SL3(FS3) 1.5
Safety factor against sliding for the SL4(FS4) 1.5
Friction factor (m) 0.35

1.4 LOAD COMBINATION

Index Load Case Name Load Case Description
1 SW SELF WEIGHT
2 SN SNOW LOAD
3 DL DEAD LOAD
4 LL LIVE LOAD
5 WL WIND LOAD

1.4.1 Group - F1
Footing List = F1
Comb . ID Load Combination for stability
1 1.0 SW + 1.0 DL + 1.0 LL + 1.0 SN
2 .6 SW + .6 DL + 1.0 WL
3 .6 SW + .6 DL + .7 SL2
4 1.0 SW + 1.0 DL + .75 LL + .75 WL + .5 SN
5 1.0 SW + 1.0 DL + .75 LL + .525 SL2
Comb . ID Load Combination for Reinforcement
101 1.4 SW + 1.4 DL
102 1.2 SW + 1.2 DL + 1.6 LL + .5 SN
103 1.2 SW + 1.2 DL + 1.0 LL + 1.6 SN
104 1.2 SW + 1.2 DL + .5 WL + 1.6 SN
105 1.2 SW + 1.2 DL + 1.0 LL + 1.0 WL + .5 SN
106 1.2 SW + 1.2 DL + 1.0 LL
107 .9 SW + .9 DL + 1.0 WL
108 .9 SW

1.4.2 Group - F2
Footing List = F2
Comb . ID Load Combination for stability
1 1.0 SW + 1.0 DL + 1.0 LL + 1.0 SN
2 .6 SW + .6 DL + 1.0 WL
3 .6 SW + .6 DL + .7 SL2
4 1.0 SW + 1.0 DL + .75 LL + .75 WL + .5 SN
5 1.0 SW + 1.0 DL + .75 LL + .525 SL2
Comb . ID Load Combination for Reinforcement
101 1.4 SW + 1.4 DL

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 5

102 1.2 SW + 1.2 DL + 1.6 LL + .5 SN

103 1.2 SW + 1.2 DL + 1.0 LL + 1.6 SN
104 1.2 SW + 1.2 DL + .5 WL + 1.6 SN
105 1.2 SW + 1.2 DL + 1.0 LL + 1.0 WL + .5 SN
106 1.2 SW + 1.2 DL + 1.0 LL
107 .9 SW + .9 DL + 1.0 WL
108 .9 SW

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018 Page 6

2. DRAWING REFERENCE DWGS

NO. DWG NO. DWG TITLE

A01 A02
NOTES
* OUTPUT UNIT : mm
3200

01
1 2
Apartment PROJECT

F1

F2

FOUNDATION LOCATION PLAN

The Resident

SQUAD CHECK
Y PROCESS PIPING VESSELS STRUCT. ELEC. INST.

Z X SCALE JOB NO. MICROFILM NO.

AS SHOWN 001

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018 Page 7

2.2 DETAIL SKETCH

OUTPUT UNIT : mm

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018 Page 8

REFERENCE DWGS
NO. DWG NO. DWG TITLE

1500 CL FOOTING
750 TOP BOTTOM

TYP.
75
750

#12@150

#16@150
1500

NOTES
* ANCHOR BOLT
1X4-M12 ANC. BOLTS (TYPE TYPE L)

* OUTPUT UNIT : mm

#12@150
#16@150
FOUNDATION PLAN FOOTING REINF. PLAN
75 PROJ.

Apartment PROJECT
300
100 50

TOC EL. + 0
81.25 81.25
137.5 75
TYP.
81.25
1700
1700

@200

FOUNDATION DETAIL FOR

#10

#12
137.5
300

F1
#10
81.25

SQUAD CHECK
100

8-#12
75
350

PEDESTAL
50

PROCESS PIPING VESSELS STRUCT. ELEC. INST.

LEAN CONC. 50 THK

CRUSHED STONE 100 THK
SECTION SCALE JOB NO. MICROFILM NO.

REV. DATE DESCRIPTION DRWNCHKDAPPDAPPDAPPD

AS SHOWN 001

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018 Page 9

2.2 DETAIL SKETCH

OUTPUT UNIT : mm

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018 Page 10

REFERENCE DWGS
NO. DWG NO. DWG TITLE

2500 CL FOOTING
1050 TOP BOTTOM

TYP.
75
1000

#12@150

#16@100
2000

NOTES
* ANCHOR BOLT
1X4-M12 ANC. BOLTS (TYPE TYPE L)

#12@150 * OUTPUT UNIT : mm

#16@150
FOUNDATION PLAN FOOTING REINF. PLAN
75 PROJ.

Apartment PROJECT
300
100 50

TOC EL. - 100 81.25 81.25

137.5 75
TYP.
81.25
1500

@200
#10

#12 FOUNDATION DETAIL FOR

137.5
300

F2
#10
81.25

SQUAD CHECK
100
75

8-#12
400

PEDESTAL
50

PROCESS PIPING VESSELS STRUCT. ELEC. INST.

LEAN CONC. 50 THK
CRUSHED STONE 100 THK
SECTION
SCALE JOB NO. MICROFILM NO.

REV. DATE DESCRIPTION DRWNCHKDAPPDAPPDAPPD

AS SHOWN 001

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 11

3. FOUNDATION DATA
3.1 FOOTING AND SECTION DATA
( mm ) Ft. Name F1
Ft. Type ISO
2
1500 Area 2.250 m
Ft. Thickness 350.00 mm
3
Ft. Volume 0.788 m
Ft. Weight 18.912 kN
Soil Height 1700.00 mm
3
Soil Volume 3.672 m
300 300
Soil Weight 66.096 kN
1500

Buoyancy Not Consider

Self Weight (except Pr.SW) 85.008 kN

1700

The Origin coordinate

350

The Center of gravity (0,0) mm

Section Data
( mm )
Ft.Name Direction Ft. Volume Soil Volume Pier Wt
3 3
F1 All Direct 0.788 m 3.672 m 3.672 kN

Sec.Name Section Area Ft. Weight Soil Weight Total Weight

2
S1 2.250 m 18.912 kN 66.096 kN 88.680 kN

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 12

( mm ) Ft. Name F2
Ft. Type ISO
2
Area 5.000 m

2500 Ft. Thickness 400.00 mm

3
Ft. Volume 2.000 m
Ft. Weight 48.000 kN
Soil Height 1600.00 mm
3
Soil Volume 7.865 m
300 300 Soil Weight 141.570 kN
2000

Buoyancy Not Consider

Self Weight (except Pr.SW) 189.570 kN

1600
1500
The Origin coordinate
400
The Center of gravity (0,0) mm

Section Data
( mm )
Ft.Name Direction Ft. Volume Soil Volume Pier Wt
3 3
F2 All Direct 2.000 m 7.865 m 3.240 kN

Sec.Name Section Area Ft. Weight Soil Weight Total Weight

2
S1 5.000 m 48.000 kN 141.570 kN 192.810 kN

3.2 PIER DATA

Off X , Off Y is offset position from the Center of the footing
If Pier Shape is Circle or Circle wall, Pl is a Diameter. and Pw is a Inner Diameter
Area is pier concrete area
Weight is pier and inner soil weight in case circle wall except Tank1 Type(Circle Ring Footing Shape)
2
Unit( Length : mm , Weight : kN , Area : m )
Ft.Name Pr.Name Shape Pl Pw Ph Area Weight Off X Off Y
F1 1 Rectangle 300.000 300.000 1700.000 0.090 3.672 0.000 0.000
F2 2 Rectangle 300.000 300.000 1500.000 0.090 3.240 -200.000 0.000

3.3 LOAD CASE

Fz
Fy
Mz
Input the point loads in the global coordinate system direction. Positive directions of moments (shown in the sketch) are
My based on the right hand rule.
Fx
Mx

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 13

Index Load Case Name Load Case Description

1 SW SELF WEIGHT
2 SN SNOW LOAD
3 DL DEAD LOAD
4 LL LIVE LOAD
5 WL WIND LOAD

Unit( kN , kN-m )
Ft.Name Pr.Name Load Case Fx Fy Fz Mx My
1 0 0 -3.67 0 0
2 0 0 0 0 0
1 3 0 0 -68 0 0
F1
4 0 0 -25 0 0
5 0 0 -2 0 0
Footing SW 0.000 0.000 -85.008 0.000 0.000
1 0 0 -3.24 0 0
2 0 0 0 0 0
2 3 0 0 -118 0 18
F2
4 0 0 -60 0 16.34
5 0 0 -0.3 0 2
Footing SW 0.000 0.000 -189.570 0.000 0.000

3.4 LOAD COMBINATION

In Pier Top In Footing Bottom In Footing Bottom Center
without Self Weight with Pier Self Weight, with Pier & Footing Self Weight & Soil Weight,
But without Footing Self Weight, Case PileType
in centroid of Pile Group
Case NonPileType
in centroid of Footing

3.4.1 Load Combination in Pier Top (Without SW)

Group 1 - F1 Unit( kN , kN-m )
Ft.Name Pr.Name L.Comb. SFx SFy SFz SMx SMy
F1 1 0.000 0.000 -93.000 0.000 0.000
2 0.000 0.000 -42.800 0.000 0.000
3 0.000 0.000 -40.800 0.000 0.000
4 0.000 0.000 -88.250 0.000 0.000
1 5 0.000 0.000 -86.750 0.000 0.000
101 0.000 0.000 -95.200 0.000 0.000
102 0.000 0.000 -121.600 0.000 0.000
103 0.000 0.000 -106.600 0.000 0.000
104 0.000 0.000 -82.600 0.000 0.000

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 14

105 0.000 0.000 -108.600 0.000 0.000

106 0.000 0.000 -106.600 0.000 0.000
107 0.000 0.000 -63.200 0.000 0.000
108 0.000 0.000 0.000 0.000 0.000

Group 2 - F2 Unit( kN , kN-m )

Ft.Name Pr.Name L.Comb. SFx SFy SFz SMx SMy
1 0.000 0.000 -178.000 0.000 34.340
2 0.000 0.000 -71.100 0.000 12.800
3 0.000 0.000 -70.800 0.000 10.800
4 0.000 0.000 -163.225 0.000 31.755
5 0.000 0.000 -163.000 0.000 30.255
101 0.000 0.000 -165.200 0.000 25.200
F2 2 102 0.000 0.000 -237.600 0.000 47.744
103 0.000 0.000 -201.600 0.000 37.940
104 0.000 0.000 -141.750 0.000 22.600
105 0.000 0.000 -201.900 0.000 39.940
106 0.000 0.000 -201.600 0.000 37.940
107 0.000 0.000 -106.500 0.000 18.200
108 0.000 0.000 0.000 0.000 0.000

3.4.2 Load Combination in Footing Bottom (With Pier SW)

Group 1 - F1 Unit( kN , kN-m )
Ft.Name Pr.Name L.Comb. SFx SFy SFz SMx SMy
1 0.000 0.000 -96.672 0.000 0.000
2 0.000 0.000 -45.003 0.000 0.000
3 0.000 0.000 -43.003 0.000 0.000
4 0.000 0.000 -91.922 0.000 0.000
5 0.000 0.000 -90.422 0.000 0.000
101 0.000 0.000 -100.341 0.000 0.000
F1 1 102 0.000 0.000 -126.006 0.000 0.000
103 0.000 0.000 -111.006 0.000 0.000
104 0.000 0.000 -87.006 0.000 0.000
105 0.000 0.000 -113.006 0.000 0.000
106 0.000 0.000 -111.006 0.000 0.000
107 0.000 0.000 -66.505 0.000 0.000
108 0.000 0.000 -3.305 0.000 0.000

Group 2 - F2 Unit( kN , kN-m )

Ft.Name Pr.Name L.Comb. SFx SFy SFz SMx SMy
F2 1 0.000 0.000 -181.240 0.000 34.340
2 0.000 0.000 -73.044 0.000 12.800
3 0.000 0.000 -72.744 0.000 10.800
4 0.000 0.000 -166.465 0.000 31.755
2
5 0.000 0.000 -166.240 0.000 30.255
101 0.000 0.000 -169.736 0.000 25.200
102 0.000 0.000 -241.488 0.000 47.744
103 0.000 0.000 -205.488 0.000 37.940

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 15

104 0.000 0.000 -145.638 0.000 22.600

105 0.000 0.000 -205.788 0.000 39.940
106 0.000 0.000 -205.488 0.000 37.940
107 0.000 0.000 -109.416 0.000 18.200
108 0.000 0.000 -2.916 0.000 0.000

3.4.3 Load Combination in Footing Bottom Center (With Pier & Footing SW)
Load Combination of Elastic Condition
Group 1 - F1
- C.G. of Load is coordinate from left bottom. Unit : mm Unit( kN , kN-m )
Ft.Name L.Comb. SFx SFy SFz SMx SMy C.G. of Loads
1 0.000 0.000 -181.680 0.000 0.000 750.0 , 750.0
2 0.000 0.000 -96.008 0.000 0.000 750.0 , 750.0
F1 3 0.000 0.000 -94.008 0.000 0.000 750.0 , 750.0
4 0.000 0.000 -176.930 0.000 0.000 750.0 , 750.0
5 0.000 0.000 -175.430 0.000 0.000 750.0 , 750.0

Group 2 - F2
- C.G. of Load is coordinate from left bottom. Unit : mm Unit( kN , kN-m )
Ft.Name L.Comb. SFx SFy SFz SMx SMy C.G. of Loads
1 0.000 0.000 -370.810 0.000 -1.908 1152.2 , 1000.0
2 0.000 0.000 -186.786 0.000 -1.809 1194.4 , 1000.0
F2 3 0.000 0.000 -186.486 0.000 -3.749 1194.5 , 1000.0
4 0.000 0.000 -356.035 0.000 -1.538 1156.5 , 1000.0
5 0.000 0.000 -355.810 0.000 -2.993 1156.6 , 1000.0

Load Combination of Ultimate Condition

Group 1 - F1
- C.G. of Load is coordinate from left bottom. Unit : mm Unit( kN , kN-m )
Ft.Name Sec.Nam L.Comb. SFx SFy SFz SMx SMy C.G. of Loads
101 0.000 0.000 -219.352 0.000 0.000 750.0 , 750.0
102 0.000 0.000 -228.016 0.000 0.000 750.0 , 750.0
103 0.000 0.000 -213.016 0.000 0.000 750.0 , 750.0
104 0.000 0.000 -189.016 0.000 0.000 750.0 , 750.0
F1 S1
105 0.000 0.000 -215.016 0.000 0.000 750.0 , 750.0
106 0.000 0.000 -213.016 0.000 0.000 750.0 , 750.0
107 0.000 0.000 -143.012 0.000 0.000 750.0 , 750.0
108 0.000 0.000 -79.812 0.000 0.000 750.0 , 750.0

Group 2 - F2
- C.G. of Load is coordinate from left bottom. Unit : mm Unit( kN , kN-m )
Ft.Name Sec.Nam L.Comb. SFx SFy SFz SMx SMy C.G. of Loads
F2 S1 101 0.000 0.000 -435.134 0.000 -8.747 1155.5 , 1000.0

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 16

102 0.000 0.000 -468.972 0.000 -0.554 1138.0 , 1000.0

103 0.000 0.000 -432.972 0.000 -3.158 1146.0 , 1000.0
104 0.000 0.000 -373.122 0.000 -6.528 1163.1 , 1000.0
105 0.000 0.000 -433.272 0.000 -1.218 1145.9 , 1000.0
106 0.000 0.000 -432.972 0.000 -3.158 1146.0 , 1000.0
107 0.000 0.000 -280.029 0.000 -3.683 1176.8 , 1000.0
108 0.000 0.000 -173.529 0.000 -0.583 1247.0 , 1000.0

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 17

4. CHECK OF STABILITY
4.1 CHECK OF SLIDING
mSFz + P.F
Formula : > Fs -> OK (Bi-Axial)
SFx2 + SFy2
P.F = Passive Force (apply only in case checked passive force, mark by P )
Group 1 - F1 Unit ( kN )
( mSFz + P.F ) / SFx + SFy
2 2
Ft.Name Dir. L.Comb. Fs(i) Result
SFx + SFy = 0 , Then N/A
2 2
F1 Bi-Axial 5 1.8 OK

Group 2 - F2 Unit ( kN )
( mSFz + P.F ) / SFx + SFy
2 2
Ft.Name Dir. L.Comb. Fs(i) Result
SFx + SFy = 0 , Then N/A
2 2
F2 Bi-Axial 5 1.8 OK

4.2 CHECK OF OVERTURNING MOMENT

Formula : (SMry / SMoy or SMrx / SMox) > OVM(i) -> OK
Group 1 - F1 Unit ( kN-m )
Ft.Name Dir. L.Comb. SMry / SMoy = OVM or SMrx / SMox = OVM OVM(i) Result
X 5 SMo = 0 , Then N/A 1.5 OK
F1
Y 5 SMo = 0 , Then N/A 1.5 OK

Group 2 - F2 Unit ( kN-m )

Ft.Name Dir. L.Comb. SMry / SMoy = OVM or SMrx / SMox = OVM OVM(i) Result
X 3 -233.11 / -3.75 = 62.18 1.5 OK
F2
Y 3 SMo = 0 , Then N/A 1.5 OK

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 18

4.3 CHECK OF CONTACT PRESSURE

4.3.1 Contact Pressure Formula
'Handbook CONCRETE ENGINEERING' Second Edition edited by Mark Fintel

SFz SMy X(i) SMx Y(i)

q1,q2 =
Af Iy Ix
if q1 or q2 < 0 , than q1 and q2 will be recalculated
by following formula
L
q(x) width(x) X dx
Px = 0 L
0
q(x) width(x) dx
P = L0 q(x) width(x) dx

4.3.2 Input Data

2 4 4
Ft.Name Af (m ) Fl (m ) Fw (m ) Ix (m ) Iy (m )
F1 2.250 1.500 1.500 0.4219 0.4219
F2 5.000 2.500 2.000 1.6667 2.6042

4.3.3 Pressure Check

- Qa = Soil bearing capacity
- Uc = Uplift Allowable capacity
Group 1 - F1
- XY-Direction (Bi-Axial) Unit( kN , kN-m , kN/m )
2

Ft.Name L.Comb. q1 q2 ci cj Qmax Qa Cont.A.R Result

F1 1 80.747 80.747 0.000 1.500 80.7 81.0(gross) 100 / 80 % OK

Group 2 - F2
- XY-Direction (Bi-Axial) Unit( kN , kN-m , kN/m )
2

Ft.Name L.Comb. q1 q2 ci cj Qmax Qa Cont.A.R Result

F2 1 73.246 75.078 0.000 2.500 75.1 81.0(gross) 100 / 80 % OK

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 19

5. DESIGN OF FOOTING
5.1 DESIGN MOMENT AND SHEAR FORCE
Footing design is in accordance with unltimate strength method at footing bottom.
Calculated total pier load as
SQ = SFz - Self Weight Factor (Soil Weight + Footing Weight)
Ft.Name : Footing Name , Sec.Name : Strip Name for Footing Reinforcement Design
Dir. : Direction , L.Comb. : Load Combination Index , Sl or Sw : Strip X or Y width

5.1.1 Data
Group 1 - F1 Unit( mm , kN , kN-m )
Ft.Name Sec.Nam Dir. L.Comb. Fl or Fw Sl or Sw SFz SM SQ
101 1500.00 1500.00 219.352 0.00 100.341
102 1500.00 1500.00 228.016 0.00 126.006
103 1500.00 1500.00 213.016 0.00 111.006
104 1500.00 1500.00 189.016 0.00 87.006
S1 X
105 1500.00 1500.00 215.016 0.00 113.006
106 1500.00 1500.00 213.016 0.00 111.006
107 1500.00 1500.00 143.012 0.00 66.505
108 1500.00 1500.00 79.812 0.00 3.305
F1
101 1500.00 1500.00 219.352 0.000 100.341
102 1500.00 1500.00 228.016 0.000 126.006
103 1500.00 1500.00 213.016 0.000 111.006
104 1500.00 1500.00 189.016 0.000 87.006
S1 Y
105 1500.00 1500.00 215.016 0.000 113.006
106 1500.00 1500.00 213.016 0.000 111.006
107 1500.00 1500.00 143.012 0.000 66.505
108 1500.00 1500.00 79.812 0.000 3.305

Group 2 - F2 Unit( mm , kN , kN-m )

Ft.Name Sec.Nam Dir. L.Comb. Fl or Fw Sl or Sw SFz SM SQ
101 2500.00 2000.00 435.134 -8.75 169.736
102 2500.00 2000.00 468.972 -0.55 241.488
103 2500.00 2000.00 432.972 -3.16 205.488
104 2500.00 2000.00 373.122 -6.53 145.638
S1 X
105 2500.00 2000.00 433.272 -1.22 205.788
106 2500.00 2000.00 432.972 -3.16 205.488
F2
107 2500.00 2000.00 280.029 -3.68 109.416
108 2500.00 2000.00 173.529 -0.58 2.916
101 2000.00 2500.00 435.134 0.000 169.736
102 2000.00 2500.00 468.972 0.000 241.488
S1 Y
103 2000.00 2500.00 432.972 0.000 205.488
104 2000.00 2500.00 373.122 0.000 145.638

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 20

105 2000.00 2500.00 433.272 0.000 205.788

106 2000.00 2500.00 432.972 0.000 205.488
107 2000.00 2500.00 280.029 0.000 109.416
108 2000.00 2500.00 173.529 0.000 2.916

5.1.2 Design Parameters

Yield Strength - #6 ~ #18 : fy1 , #20 ~ : fy2
f_cl : Clear Cover for edge of footing reinforcement
f_clt : Clear Cover for top of footing reinforcement
f_clb : Clear Cover for bottom of footing reinforcement
Loc. : Location of Critical Point from left side of footing

2
Unit(N/mm ,mm)
f(Flexure) f(Shear) f'c fy1 fy2 f_cl f_clt f_clb
0.9 0.75 28.00 390.00 390.00 75.0 75.0 50.0

5.2 REQUIRED REINFORCEMENT

5.2.1 Reinforcement Formula
- Shrinkage and temperature reinforcement
As = fac b h , fac = 0.002 ( User input)
- Required Reinforcement by Analysis
As As2
- At every section of flexural members where tensile reinforcement is required
As As5
As As4
- The requirements of Eq (6.3.2) need not be applied, if every section As provided is
at least one -third greater than that required by analysis
As2 = r.req b d
As3 = 1.333 r.req b d
1.4
As4 = bd
fy
0.25 fck
As5 = bd
fy
Asmax = 0.75 rb b d
fck 0.003 Es
rb = 0.85 b 1
fy 0.003 Es + fy
Selected As = Max ( As1 , As2 , Min ( As3 , Max ( As4 , As5 ) ) )
If Selected As < Using As < Asmax , then OK!!

Note : The reinforcement is calculated bases on the maximum moment under the foundation in each direction.
But, the 'ISO' , 'OCT' , 'HEX' , 'COMB' , 'TANK1' foundations are calaulated as face pier
Where,
Mu 0.85 fck 2Rn
Rn =
fbd
2 , f = 0.9 , r.req =
fy (
1- 1-
0.85fck )

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 21

5.2.2 Check of Footing Reinforcement

Group 1 - F1
Footing Name : F1 GroupType : Isolated
- X direction (All Width)

2
Sec.Name L.Comb. Using Bar (mm) Loc. (m) Width b (m) d (mm) As (mm )
108 top 10 - #12 @ 150 0.750 1.500 269.000 1130.974
S1
102 botom 10 - #16 @ 150 0.900 1.500 292.000 2010.620

Sec.Name L.Comb. Mu (kN-m) Rn r.Req

108 top - - -
S1
102 bottom 27.362 0.238 0.0006
2 2 2 2 2 2
Sec.Name L.Comb. As1(mm ) As2(mm ) As3(mm ) As4(mm ) As5(mm ) Asmax(mm )
108 top 525.000 - - 1448.462 1368.668 9513.761
S1
102 bottom 525.000 268.314 357.662 1572.308 1485.691 10327.210
2 2
Sec.Name L.Comb. Using As(mm ) Select As(mm ) Result
108 top 1130.974 525.000 OK
S1
102 bottom 2010.620 525.000 OK

- Y direction (All Width)

2
Sec.Name L.Comb. Using Bar (mm) Loc. (m) Width b (m) d (mm) As (mm )
108 top 10 - #12 @ 150 0.750 1.500 253.000 1130.974
S1
102 botom 10 - #16 @ 150 0.900 1.500 276.000 2010.620

Sec.Name L.Comb. Mu (kN-m) Rn r.Req

108 top - - -
S1
102 bottom 27.362 0.266 0.0007
2 2 2 2 2 2
Sec.Name L.Comb. As1(mm ) As2(mm ) As3(mm ) As4(mm ) As5(mm ) Asmax(mm )
108 top 525.000 - - 1362.308 1287.260 8947.887
S1
102 bottom 525.000 284.040 378.626 1486.154 1404.284 9761.330
2 2
Sec.Name L.Comb. Using As(mm ) Select As(mm ) Result
108 top 1130.974 525.000 OK
S1
102 bottom 2010.620 525.000 OK

Group 2 - F2
Footing Name : F2 GroupType : Isolated
- X direction (All Width)

2
Sec.Name L.Comb. Using Bar (mm) Loc. (m) Width b (m) d (mm) As (mm )
108 top 14 - #12 @ 150 1.250 2.000 319.000 1583.363
S1
102 botom 20 - #16 @ 100 1.200 2.000 342.000 4021.239

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 22

Sec.Name L.Comb. Mu (kN-m) Rn r.Req

108 top - - -
S1
102 bottom 158.219 0.752 0.0020
2 2 2 2 2 2
Sec.Name L.Comb. As1(mm ) As2(mm ) As3(mm ) As4(mm ) As5(mm ) Asmax(mm )
108 top 800.000 - - 2290.257 2164.089 15042.820
S1
102 bottom 800.000 1339.523 1785.584 2455.385 2320.121 16127.410
2 2
Sec.Name L.Comb. Using As(mm ) Select As(mm ) Result
108 top 1583.363 800.000 OK
S1
102 bottom 4021.239 1785.584 OK

- Y direction (All Width)

2
Sec.Name L.Comb. Using Bar (mm) Loc. (m) Width b (m) d (mm) As (mm )
108 top 17 - #12 @ 150 1.000 2.500 303.000 1922.655
S1
102 botom 17 - #16 @ 150 1.150 2.500 326.000 3418.053

Sec.Name L.Comb. Mu (kN-m) Rn r.Req

108 top - - -
S1
102 bottom 84.708 0.354 0.0009
2 2 2 2 2 2
Sec.Name L.Comb. As1(mm ) As2(mm ) As3(mm ) As4(mm ) As5(mm ) Asmax(mm )
108 top 1000.000 - - 2719.231 2569.432 17860.400
S1
102 bottom 1000.000 745.880 994.258 2925.641 2764.471 19216.140
2 2
Sec.Name L.Comb. Using As(mm ) Select As(mm ) Result
108 top 1922.655 1000.000 OK
S1
102 bottom 3418.053 1000.000 OK

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 23

Title

Bending Moment Diagram 1500

Foundation name Section name Direction L/C ID

F1 S1 X 102
Analysis Method
Conventional Rigid Method with reaction (Method 1)

1500
SFz SMy Moment intia 4
-228.016 kN 0.000 kN-m 0.4219 m
Area 2 Contact Area 2 Critical Point Method
2.250 m 2.250 m (100 %) Critical Point
Critical Value
Mubottom = 27.362 kN-m , Mutop = 0 kN-m

00
0

0
60

90

15
0

[ mm ]

[Loading]

[ kN , kN/m ]

152.01 152.01

[B.M.D] [ kN-m ]

-27.4
-20.5
-13.7
-6.8
0
7.21 7.21
6.8
13.7
20.5
27.36
27.4

[B/L.M.D] [ kN-m / m ]

-18.2
-13.7
-9.1
-4.6
0
4.81 4.81
4.6
9.1
13.7
18.24
18.2

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 24

Title

Bending Moment Diagram 1500

Foundation name Section name Direction L/C ID

F1 S1 X 108
Analysis Method
Conventional Rigid Method with reaction (Method 1)

1500
SFz SMy Moment intia 4
-79.812 kN 0.000 kN-m 0.4219 m
Area 2 Contact Area 2 Critical Point Method
2.250 m 2.250 m (100 %) Critical Point
Critical Value
Mubottom = 9.577 kN-m , Mutop = 0 kN-m

00
0

0
60

90

15
0

[ mm ]

[Loading]

[ kN , kN/m ]

53.21 53.21

[B.M.D] [ kN-m ]

-9.6
-7.2
-4.8
-2.4
0
2.53 2.53
2.4
4.8
7.2
9.58
9.6

[B/L.M.D] [ kN-m / m ]

-6.4
-4.8
-3.2
-1.6
0
1.68 1.68
1.6
3.2
4.8
6.39
6.4

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 25

Title

Bending Moment Diagram 1500

Foundation name Section name Direction L/C ID

F1 S1 Y 102
Analysis Method
Conventional Rigid Method with reaction (Method 1)

1500
SFz SMx Moment intia 4
-228.016 kN 0.000 kN-m 0.4219 m
Area 2 Contact Area 2 Critical Point Method
2.250 m 2.250 m (100 %) Critical Point
Critical Value
Mubottom = 27.362 kN-m , Mutop = 0 kN-m

00
0

0
60

90

15
0

[ mm ]

[Loading]

[ kN , kN/m ]

152.01 152.01

[B.M.D] [ kN-m ]

-27.4
-20.5
-13.7
-6.8
0
7.21 7.21
6.8
13.7
20.5
27.36
27.4

[B/L.M.D] [ kN-m / m ]

-18.2
-13.7
-9.1
-4.6
0
4.81 4.81
4.6
9.1
13.7
18.24
18.2

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 26

Title

Bending Moment Diagram 1500

Foundation name Section name Direction L/C ID

F1 S1 Y 108
Analysis Method
Conventional Rigid Method with reaction (Method 1)

1500
SFz SMx Moment intia 4
-79.812 kN 0.000 kN-m 0.4219 m
Area 2 Contact Area 2 Critical Point Method
2.250 m 2.250 m (100 %) Critical Point
Critical Value
Mubottom = 9.577 kN-m , Mutop = 0 kN-m

00
0

0
60

90

15
0

[ mm ]

[Loading]

[ kN , kN/m ]

53.21 53.21

[B.M.D] [ kN-m ]

-9.6
-7.2
-4.8
-2.4
0
2.53 2.53
2.4
4.8
7.2
9.58
9.6

[B/L.M.D] [ kN-m / m ]

-6.4
-4.8
-3.2
-1.6
0
1.68 1.68
1.6
3.2
4.8
6.39
6.4

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 27

Title

Bending Moment Diagram 2500

Foundation name Section name Direction L/C ID
F2 S1 X 102
Analysis Method
Conventional Rigid Method with reaction (Method 1)

2000
SFz SMy Moment intia 4
-468.972 kN -0.554 kN-m 2.6042 m
Area 2 Contact Area 2 Critical Point Method
5.000 m 5.000 m (100 %) Critical Point
Critical Value
Mubottom = 158.219 kN-m , Mutop = 0 kN-m

00

00
0
90

12

25
0

[ mm ]

[Loading]

[ kN , kN/m ]

188.12 187.74 187.61 187.06

[B.M.D] [ kN-m ]

-158.2
-118.7
-79.1
-39.6
0 29.27
39.6
79.1 85.91
118.7
158.22
158.2

[B/L.M.D] [ kN-m / m ]

-79.1
-59.3
-39.6
-19.8
0 14.64
19.8
39.6 42.95
59.3
79.11
79.1

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 28

Title

Bending Moment Diagram 2500

Foundation name Section name Direction L/C ID
F2 S1 X 108
Analysis Method
Conventional Rigid Method with reaction (Method 1)

2000
SFz SMy Moment intia 4
-173.529 kN -0.583 kN-m 2.6042 m
Area 2 Contact Area 2 Critical Point Method
5.000 m 5.000 m (100 %) Critical Point
Critical Value
Mubottom = 58.344 kN-m , Mutop = 0 kN-m

00

00
0
90

12

25
0

[ mm ]

[Loading]

[ kN , kN/m ]

69.97 69.57 69.43 68.85

[B.M.D] [ kN-m ]

-58.3
-43.8
-29.2
-14.6
0 10.88
14.6
29.2 31.66
43.8
58.34
58.3

[B/L.M.D] [ kN-m / m ]

-29.2
-21.9
-14.6
-7.3
0 5.44
7.3
14.6 15.83
21.9
29.17
29.2

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 29

Title

Bending Moment Diagram 2500

Foundation name Section name Direction L/C ID
F2 S1 Y 102
Analysis Method
Conventional Rigid Method with reaction (Method 1)

2000
SFz SMx Moment intia 4
-468.972 kN 0.000 kN-m 1.6667 m
Area 2 Contact Area 2 Critical Point Method
5.000 m 5.000 m (100 %) Critical Point
Critical Value
Mubottom = 84.708 kN-m , Mutop = 0 kN-m

50

00
0
85

11

20
0

[ mm ]

[Loading]

[ kN , kN/m ]

234.49 234.49

[B.M.D] [ kN-m ]

-84.7
-63.5
-42.4
-21.2
0
21.2 30.26 30.26
42.4
63.5
84.71
84.7

[B/L.M.D] [ kN-m / m ]

-33.9
-25.4
-16.9
-8.5
0
8.5 12.1 12.1
16.9
25.4
33.88
33.9

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 30

Title

Bending Moment Diagram 2500

Foundation name Section name Direction L/C ID
F2 S1 Y 108
Analysis Method
Conventional Rigid Method with reaction (Method 1)

2000
SFz SMx Moment intia 4
-173.529 kN 0.000 kN-m 1.6667 m
Area 2 Contact Area 2 Critical Point Method
5.000 m 5.000 m (100 %) Critical Point
Critical Value
Mubottom = 31.343 kN-m , Mutop = 0 kN-m

50

00
0
85

11

20
0

[ mm ]

[Loading]

[ kN , kN/m ]

86.76 86.76

[B.M.D] [ kN-m ]

-31.3
-23.5
-15.7
-7.8
0
7.8 11.2 11.2
15.7
23.5
31.34
31.3

[B/L.M.D] [ kN-m / m ]

-12.5
-9.4
-6.3
-3.1
0
3.1 4.48 4.48
6.3
9.4
12.54
12.5

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 31

5.3 ONE WAY SHEAR FORCE

5.3.1 One-Way Shear Formula
- f Vc = 0.75 1/6 fck B'w d
- Vu <= f Vc , then OK!!

5.3.2 Check of One-Way Shear

Group 1 - F1

Footing Name : F1 GroupType : Isolated PileType : False

Unit : mm
1500
1500

1192

1192

- X direction One-Way Shear (All Width)

Sec.Name L.Comb. Loc. (mm) d (mm) Bw (mm) fVc (kN) Vu (kN) Result
S1 102 1192 292 1500 289.71 46.819 OK
- Y direction One-Way Shear (All Width)
Sec.Name L.Comb. Loc. (mm) d (mm) Bw (mm) fVc (kN) Vu (kN) Result
S1 102 1192 276 1500 273.835 46.819 OK

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 32

Group 2 - F2

Footing Name : F2 GroupType : Isolated PileType : False

Unit : mm

2500
2000

1492

1542

- X direction One-Way Shear (All Width)

Sec.Name L.Comb. Loc. (mm) d (mm) Bw (mm) fVc (kN) Vu (kN) Result
S1 102 1542 342 2000 452.423 179.396 OK
- Y direction One-Way Shear (All Width)
Sec.Name L.Comb. Loc. (mm) d (mm) Bw (mm) fVc (kN) Vu (kN) Result
S1 102 1492 326 2500 539.072 119.119 OK

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 33

Title

Shear Force Diagram 1500

Foundation name Section name Direction L/C ID

F1 S1 X 102
Analysis Method
Conventional Rigid Method with reaction (Method 1)

1500
SFz SMy Moment intia 4
-228.016 kN 0.000 kN-m 0.4219 m
Area 2 Contact Area 2 Critical Point Method
2.250 m 2.250 m (100 %) Critical Point
Critical Value
Vu = -46.819 kN

92

00
0

0
60

90

11

15
0

[ mm ]

[Loading]

[ kN , kN/m ]

152.01 152.01

[S.F.D] [ kN ]
91.21
91.2
68.4
46.82
45.6
22.8
0
-22.8
-46.82
-45.6
-68.4
-91.2

[S/L.F.D] [ kN / m ]
60.8
60.8
45.6
31.21
30.4
15.2
0
-15.2
-31.21
-30.4
-45.6
-60.8

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 34

Title

Shear Force Diagram 1500

Foundation name Section name Direction L/C ID

F1 S1 Y 102
Analysis Method
Conventional Rigid Method with reaction (Method 1)

1500
SFz SMx Moment intia 4
-228.016 kN 0.000 kN-m 0.4219 m
Area 2 Contact Area 2 Critical Point Method
2.250 m 2.250 m (100 %) Critical Point
Critical Value
Vu = -46.819 kN

92

00
0

0
60

90

11

15
0

[ mm ]

[Loading]

[ kN , kN/m ]

152.01 152.01

[S.F.D] [ kN ]
91.21
91.2
68.4
46.82
45.6
22.8
0
-22.8
-46.82
-45.6
-68.4
-91.2

[S/L.F.D] [ kN / m ]
60.8
60.8
45.6
31.21
30.4
15.2
0
-15.2
-31.21
-30.4
-45.6
-60.8

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 35

Title

Shear Force Diagram 2500

Foundation name Section name Direction L/C ID
F2 S1 X 102
Analysis Method
Conventional Rigid Method with reaction (Method 1)

2000
SFz SMy Moment intia 4
-468.972 kN -0.554 kN-m 2.6042 m
Area 2 Contact Area 2 Critical Point Method
5.000 m 5.000 m (100 %) Critical Point
Critical Value
Vu = -179.396 kN

00

42

00
0
90

12

15

25
0

[ mm ]

[Loading]

[ kN , kN/m ]

188.12 187.74 187.61 187.06

[S.F.D] [ kN ]

243.5
182.7
121.8 104.9
60.9
0
-60.9
-121.8
-179.4
-182.7
-243.5

[S/L.F.D] [ kN / m ]

121.8
91.3
60.9 52.45
30.4
0
-30.4
-60.9
-89.7
-91.3
-121.8

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 36

Title

Shear Force Diagram 2500

Foundation name Section name Direction L/C ID
F2 S1 Y 102
Analysis Method
Conventional Rigid Method with reaction (Method 1)

2000
SFz SMx Moment intia 4
-468.972 kN 0.000 kN-m 1.6667 m
Area 2 Contact Area 2 Critical Point Method
5.000 m 5.000 m (100 %) Critical Point
Critical Value
Vu = -119.119 kN

50

92

00
0
85

11

14

20
0

[ mm ]

[Loading]

[ kN , kN/m ]

234.49 234.49

[S.F.D] [ kN ]
199.31
199.3
149.5 119.12
99.7
49.8
0
-49.8
-99.7 -119.12
-149.5
-199.3

[S/L.F.D] [ kN / m ]
79.72
79.7
59.8 47.65
39.9
19.9
0
-19.9
-39.9 -47.65
-59.8
-79.7

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 37

5.4 TWO WAY SHEAR FORCE

5.4.1 Two-Way Shear Formula
Vu = SFz Shade Ratio
f Vc1 = 0.75 1/6 (1 + 2/ b c) fck bo d
f Vc2 = 0.75 1/6 (1 + as d / 2 bo) fck bo d
f Vc3 = 0.75 1/3 fck bo d
f Vc = Min(f Vc1 , f Vc2 , f Vc3)
Vu f Vc , then OK
where
b c = ratio of long side to short side of the column, concentrated load or reaction area
as = 40 for interior colimns
= 30 for edge columns
= 20 for corner columns
bo = perimeter of critical section
Footing Area - Punching Area
Shade Ratio =
Footing Area

5.4.2 Check of Two-WayShear

2
Ft.Name F1 Punching Area 350464.000 mm

1500 Pr.Name 1 Ratio Shade 0.844

Shape Rectangle f Vc1 1372.066 kN

L.Comb. 102 f Vc2 1585.292 kN

1500

Pl 300 mm f Vc3 914.710 kN

1
Pw 300 mm f Vc 914.710 kN

bo / d 2368 / 292 mm Vu 106.379 kN

bc / as 1 / 40 Result OK

2
Ft.Name F2 Punching Area 412164.000 mm

Pr.Name 2 Ratio Shade 0.918

2500

Shape Rectangle f Vc1 1742.735 kN

L.Comb. 102 f Vc2 2128.200 kN

2000

Pl 300 mm f Vc3 1161.823 kN

2

Pw 300 mm f Vc 1161.823 kN

bo / d 2568 / 342 mm Vu 221.581 kN

bc / as 1 / 40 Result OK

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 1

SUMMARY REPORT FOR FOUNDATION DESIGN

Project Information
Project Name Apartment
Structure Name The Resident

1. CHECK OF STABILITY
1.1 Check of Sliding Force (Bi-Axial)
Ft.Name # L/C Fs Allowable Result
1 N/A 1.8 OK
2 N/A 1.8 OK
F1 3 N/A 1.8 OK
4 N/A 1.8 OK
5 N/A 1.8 OK
1 N/A 1.8 OK
2 N/A 1.8 OK
F2 3 N/A 1.8 OK
4 N/A 1.8 OK
5 N/A 1.8 OK

1.2 Check of Overturning Moment

Ft.Name # L/C X - OVM Y - OVM Allowable Result
1 N/A N/A 1.5 OK / OK
2 N/A N/A 1.5 OK / OK
F1 3 N/A N/A 1.5 OK / OK
4 N/A N/A 1.5 OK / OK
5 N/A N/A 1.5 OK / OK
1 242.93 N/A 1.5 OK / OK
2 129.08 N/A 1.5 OK / OK
F2 3 62.18 N/A 1.5 OK / OK
4 289.37 N/A 1.5 OK / OK
5 148.6 N/A 1.5 OK / OK

1.3 Check of Bearing Pressure (Bi-Axial)

2
Ft.Name # L/C Qu(kN/m ) Allowable Result
1 80.75 81 OK
2 42.67 81 OK
F1 3 41.78 81 OK
4 78.64 81 OK
5 77.97 81 OK
1 75.08 81 OK
F2 2 38.23 81 OK
3 39.1 81 OK

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 2

4 71.95 81 OK
5 72.6 81 OK

2. DESIGN OF FOOTING
2.1 Check of Reinforcement 2
(Unit : mm )
Ft.Name Sec.Nam # L/C Req.As top / bottom Used.As top / bottom Result
101 525.00 / 525.00 1130.97 / 2010.62 OK / OK
102 525.00 / 525.00 1130.97 / 2010.62 OK / OK
103 525.00 / 525.00 1130.97 / 2010.62 OK / OK
104 525.00 / 525.00 1130.97 / 2010.62 OK / OK
S1 (X)
105 525.00 / 525.00 1130.97 / 2010.62 OK / OK
106 525.00 / 525.00 1130.97 / 2010.62 OK / OK
107 525.00 / 525.00 1130.97 / 2010.62 OK / OK
108 525.00 / 525.00 1130.97 / 2010.62 OK / OK
F1
101 525.00 / 525.00 1130.97 / 2010.62 OK / OK
102 525.00 / 525.00 1130.97 / 2010.62 OK / OK
103 525.00 / 525.00 1130.97 / 2010.62 OK / OK
104 525.00 / 525.00 1130.97 / 2010.62 OK / OK
S1 (Y)
105 525.00 / 525.00 1130.97 / 2010.62 OK / OK
106 525.00 / 525.00 1130.97 / 2010.62 OK / OK
107 525.00 / 525.00 1130.97 / 2010.62 OK / OK
108 525.00 / 525.00 1130.97 / 2010.62 OK / OK
101 800.00 / 1604.85 1583.36 / 4021.24 OK / OK
102 800.00 / 1785.58 1583.36 / 4021.24 OK / OK
103 800.00 / 1630.38 1583.36 / 4021.24 OK / OK
104 800.00 / 1379.11 1583.36 / 4021.24 OK / OK
S1 (X)
105 800.00 / 1643.31 1583.36 / 4021.24 OK / OK
106 800.00 / 1630.38 1583.36 / 4021.24 OK / OK
107 800.00 / 1039.06 1583.36 / 4021.24 OK / OK
108 800.00 / 800.00 1583.36 / 4021.24 OK / OK
F2
101 1000.00 / 1000.00 1922.65 / 3418.05 OK / OK
102 1000.00 / 1000.00 1922.65 / 3418.05 OK / OK
103 1000.00 / 1000.00 1922.65 / 3418.05 OK / OK
104 1000.00 / 1000.00 1922.65 / 3418.05 OK / OK
S1 (Y)
105 1000.00 / 1000.00 1922.65 / 3418.05 OK / OK
106 1000.00 / 1000.00 1922.65 / 3418.05 OK / OK
107 1000.00 / 1000.00 1922.65 / 3418.05 OK / OK
108 1000.00 / 1000.00 1922.65 / 3418.05 OK / OK

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 3

2.2 Check of One Way Shear (Unit : kN)

Ft.Name Sec.Nam # L/C fVc Vu Result
101 289.71 45.04 OK
102 289.71 46.82 OK
103 289.71 43.74 OK
104 289.71 38.81 OK
S1 (X)
105 289.71 44.15 OK
106 289.71 43.74 OK
107 289.71 29.36 OK
108 289.71 16.39 OK
F1
101 273.84 45.04 OK
102 273.84 46.82 OK
103 273.84 43.74 OK
104 273.84 38.81 OK
S1 (Y)
105 273.84 44.15 OK
106 273.84 43.74 OK
107 273.84 29.36 OK
108 273.84 16.39 OK
101 452.42 161.78 OK
102 452.42 179.40 OK
103 452.42 164.12 OK
104 452.42 139.28 OK
S1 (X)
105 452.42 165.34 OK
106 452.42 164.12 OK
107 452.42 105.22 OK
108 452.42 66.17 OK
F2
101 539.07 110.52 OK
102 539.07 119.12 OK
103 539.07 109.97 OK
104 539.07 94.77 OK
S1 (Y)
105 539.07 110.05 OK
106 539.07 109.97 OK
107 539.07 71.13 OK
108 539.07 44.08 OK

2.3 Check of Two Way Shear (Unit : kN)

Ft.Name # L/C Ct. Pr.Name fVc Vu Result
101 1 914.710 84.712 OK
102 1 914.710 106.379 OK
F1
103 1 914.710 93.716 OK
104 1 914.710 73.454 OK

Copyright (c) GS E&C. All Rights Reserved

 8/31/2018

Project Na. : Apartment

Calculation Sheet
of Project No. : 001

Foundation Client : xx Page 4

105 1 914.710 95.404 OK

106 1 914.710 93.716 OK
107 1 914.710 56.146 OK
108 1 914.710 2.790 OK
101 2 1161.823 155.744 OK
102 2 1161.823 221.581 OK
103 2 1161.823 188.549 OK
104 2 1161.823 133.633 OK
F2
105 2 1161.823 188.824 OK
106 2 1161.823 188.549 OK
107 2 1161.823 100.397 OK
108 2 1161.823 2.676 OK

Copyright (c) GS E&C. All Rights Reserved