  

https://unilag.edu.ng   [email protected]
  

Ruby Olubodun 

Home  My courses  EEG346  General  EEG 346 Lab Test

Started on Wednesday, 21 June 2023, 8:53 AM

State Finished
Completed on Wednesday, 21 June 2023, 9:08 AM
Time taken 14 mins 59 secs
Grade 17.00 out of 30.00 (57%)

Question 1 Correct Mark 1.00 out of 1.00

Suppose the oscilloscope was set to 1V per division on the vertical axis and 20 ms per division on the
horizontal axis, what is the rms voltage of the signal shown in the figure below?

a. 3.8 Vrms
b. 2.12 Vrms Correct

c. 3 Vrms
d. 4.24 Vrms

The correct answer is: 2.12 Vrms

Question 2 Correct Mark 1.00 out of 1.00

If the volts/division on a digital oscilloscope is set at 0.5, the largest signal that can fit on the screen
(assuming an 8 horizontal by 10 vertical division screen) is:

a. 5 volts peak-to-peak. Correct

b. 4 volts peak-to-peak.
c. 62.5 millivolts peak-to-peak.
d. 8 volts peak-to-peak

The correct answer is: 5 volts peak-to-peak.

Question 3 Correct Mark 1.00 out of 1.00

To set the gain of the non-inverting amplifier circuit shown in the figure below to +20 dB, the ratio of
the feedback resistance to input resistance at the negative terminal must be -----------.     

a. 10
b. 9 Correct

c. 7
d. 8

The correct answer is: 9

Question 4 Correct Mark 1.00 out of 1.00

Which region/s in frequency response curve of an amplifier maintains the constant level of gain and
output voltage?

a. High Frequency Region

b. Mid Frequency Region Correct

c. None of the mentioned

d. Low Frequency Region

The correct answer is: Mid Frequency Region

Question 5 Correct Mark 1.00 out of 1.00

Suppose the oscilloscope was set to 1V per division on the vertical axis and 4 ms per division on the
horizontal axis, what is the frequency of the signal shown in the figure below?

a. 30 Hz
b. 20 Hz
c. 50 Hz Correct

d. 40 Hz

The correct answer is: 50 Hz

Question 6 Correct Mark 1.00 out of 1.00

To operate an oscilloscope safely, you should:

a. All of the mentioned Correct

b. Learn to recognize potentially dangerous electrical components.

c. Ground the oscilloscope with the proper three-pronged power cord.
d. Avoid touching exposed connections in a circuit being tested even if the power is off.

The correct answer is: All of the mentioned

Question 7 Correct Mark 1.00 out of 1.00

The volts per division control on the oscilloscope is used to:

a. Scale a waveform horizontally

b. Attenuate or amplify noise signal.
c. Position a waveform vertically.
d. Set the numbers of volts each division represents Correct

The correct answer is: Set the numbers of volts each division represents
Question 8 Correct Mark 1.00 out of 1.00

Name another space that would be connected to A4 in the figure below:

a. C4 Correct

b. B5
c. A14
d. A6

The correct answer is: C4

Question 9 Correct Mark 1.00 out of 1.00

Which of the following is true?

a. All of the mentioned

b. Internal capacitor of a device causes the gain to fall off at low frequencies
c. None of the mentioned Correct

d. Coupling capacitors causes the gain to fall off at high frequencies

The correct answer is: None of the mentioned

Question 10 Correct Mark 1.00 out of 1.00

The trace rotation control on the oscilloscope is useful for:

a. Measuring pulse width.

b. Detecting sine wave signals.
c. Scaling waveforms on the screen.
d. Aligning the waveform trace with the screen's horizontal axis on an analog Correct
oscilloscope.

The correct answer is: Aligning the waveform trace with the screen's horizontal axis on an analog
oscilloscope.

Question 11 Correct Mark 1.00 out of 1.00

General representation of the frequency response curve is called……….

a. Thevenin Plot
b. Miller Plot
c. Bandwidth Plot
d. Bode Plot Correct

The correct answer is: Bode Plot

Question 12 Correct Mark 1.00 out of 1.00

Internal transistor junction capacitances affect the high-frequency response of amplifiers by…….

a. introducing phase shift as the signal frequency increases.

b. having no effect.
c. reducing the amplifier's gain and introducing phase shift as the signal frequency Correct
increases.
d. reducing the amplifier's gain.

The correct answer is: reducing the amplifier's gain and introducing phase shift as the signal
frequency increases.
Question 13 Correct Mark 1.00 out of 1.00

What happens if each terminal of a diode is placed on A5 and E5 in the figure below:

a. The diode becomes reverse biased

b. The diode is shorted Correct

c. The diode becomes forward biased

d. All of the mentioned

The correct answer is: The diode is shorted

Question 14 Correct Mark 1.00 out of 1.00

To set the gain of the non-inverting amplifier circuit shown in the figure below to 10, the ratio of the
feedback resistance to input resistance at the negative terminal must be -----------.     

a. 10
b. 7
c. 8
d. 9 Correct

The correct answer is: 9

Question 15 Incorrect Mark 0.00 out of 1.00

Grounding an oscilloscope is necessary:

a. To align the trace with the screen's horizontal axis

b. To provide a reference point for making measurements.
c. All of the mentioned Incorrect

d. For decreasing output voltage and current level.

The correct answer is: To provide a reference point for making measurements.
Question 16 Incorrect Mark 0.00 out of 1.00

What happens if each terminal of a diode is placed on A5 and F5 in the figure below:

a. The diode is short circuited

b. The diode becomes forward biased Incorrect

c. The diode becomes reverse biased

d. The diode is open circuited

The correct answer is: The diode is open circuited

Question 17 Incorrect Mark 0.00 out of 1.00

From the figure below, the overall gain of the LM 386 can generally be set by:

Figure: LM 386 IC

a. Placing a resistor between pin 1 and 8 as well as between 1 and 5

b. All of the mentioned Incorrect

c. Placing a resistor between pin 1 and 5 as well as between 2 and 8

d. Placing a resistor between pin 1 and 8 as well as between 2 and 8

The correct answer is: Placing a resistor between pin 1 and 8 as well as between 1 and 5
Question 18 Incorrect Mark 0.00 out of 1.00

Refer to the figure below. With a capacitor placed between pin 1 and 8, the LM 386 has a gain
of

Figure : LM 386 IC

a. 46 dB
b. 40 dB Incorrect

c. 16 dB
d. 10 dB

The correct answer is: 46 dB

Question 19 Incorrect Mark 0.00 out of 1.00

The rate of -20 dB/decade is almost equivalent to __________

a. -8 dB/octave Incorrect

b. -6 dB/octave
c. -10 dB/octave
d. -4 dB/octave

The correct answer is: -6 dB/octave

Question 20 Correct Mark 1.00 out of 1.00

What is the name of the item shown in the figure below?

a. Resistor
b. Battery leads
c. Alligator clips
d. Jumper wires Correct

The correct answer is: Jumper wires

Question 21 Correct Mark 1.00 out of 1.00

In the low frequency region, amplifier gain………….

a. decreases with frequency

b. is constant
c. increases with frequency Correct

d. all of the mentioned

The correct answer is: increases with frequency

Question 22 Not answered Marked out of 1.00

One characteristic of amplifiers is that the sum of the voltage gain and the bandwidth is always
constant when the roll-off is -20 dB/decade.

a. False
b. True

The correct answer is: False

Question 23 Not answered Marked out of 1.00

If the seconds/division on a digital oscilloscope is set at 0.1 ms, the amount of time represented by
the width of the screen (assuming an 8 horizontal by 10 vertical division screen) is:

a. 1s
b. 1 ms.
c. 0.1 kHz.
d. 0.8 ms.

The correct answer is: 0.8 ms.

Question 24 Not answered Marked out of 1.00

Refer to the figure shown below. Without external components, the LM 386 has a gain of

Figure: LM 386 IC

a. 26 dB
b. 20 dB
c. 16 dB
d. 10 dB

The correct answer is: 26 dB

Question 25 Not answered Marked out of 1.00

In the midband region, amplifier gain ……………

a. all of the mentioned

b. increases with frequency
c. is constant
d. decreases with frequency

The correct answer is: is constant

Question 26 Not answered Marked out of 1.00

Halving the power corresponds to a _____ dB ______.

a. 3, increase
b. 3, decrease
c. 10, decrease
d. 10, increase

The correct answer is: 3, decrease

Question 27 Not answered Marked out of 1.00

Circuit loading is caused by:

a. An input signal having too large a voltage.

b. The probe and oscilloscope interacting with the circuit being tested.
c. Putting too much weight on a circuit.
d. A 10X attenuator probe being uncompensated.

The correct answer is: The probe and oscilloscope interacting with the circuit being tested.

Question 28 Incorrect Mark 0.00 out of 1.00

An amplifier has an input signal voltage of 0.054 mV. The output voltage is 12.5 V. The voltage gain in
dB is……….

a. 116 dB.
b. 231 dB.
c. 107.3 dB.
d. 53.6 dB. Incorrect

The correct answer is: 107.3 dB.

Question 29 Incorrect Mark 0.00 out of 1.00

The value of dBm in power measurement is estimated by assuming the reference, which is equal to
________

a. 10mW
b. 1/10 mW Incorrect

c. 1/100 Mw
d. 1mW

The correct answer is: 1mW

Question 30 Correct Mark 1.00 out of 1.00

Doubling the voltage gain causes a _____ dB ______.

a. 6, increase Correct

b. 10, decrease
c. 6, decrease
d. 10, increase

The correct answer is: 6, increase

◄ Announcements Jump to...