Issue 6 -18 E

WS 5.4502
Workholding Systems MC-P Z
concentric clamping, mechanically or hydraulically operated
jaw widths 40, 60, 100 and 125 mm
Advantages Technical data
● Patented segment design Clamping principle: concentric clamping
● Compact design Operation: mechanically
● High precision and accuracy of the manufac- with a torque wrench
tured workpieces by high rigidity hydraulically
with a power unit
● High zero-point stability
● Sturdy design and good swarf protection
MC-P 40 Z
● Large jaw openings
Jaw width: 40 mm
● Extensive range of jaws
Clamping force*: 7.5 kN at 23 Nm
● Clamping of raw and finished parts without Clamping stroke: 20 mm
retrofitting Max. jaw opening: 6 – 79 mm
● Easy to maintain
MC-P 60 Z and ZH
Jaw width: 60 mm
Mechanical clamping force*: 15 kN at 60 Nm
Application Description Hydraulic clamping force*: 10 kN at 320 bar
The workholding systems MC-P Z are espe- Workholding systems of the MC-P Z series excel Clamping stroke: 30 mm
cially advantageous for 5-axis machining. by a very compact design and their patented Max. jaw opening: 6 – 150 mm
The compact design allows a good accessibil- segment design. MC-P 100 Z and ZH
ity of the tools to the workpiece. Collision-free Thanks to the adjusting spindle arranged in Jaw width: 100 mm
tool paths and a 5-sided workpiece machining the upper part of the housing, deformation in Mechanical clamping force*: 25 kN at 90 Nm
can be achieved with short standard tools. the base during clamping is ­reduced to a min- Hydraulic clamping force*: 20 kN at 270 bar
Due to the good swarf protection, workholding imum. Thus, a high rigidity of the workholding Clamping stroke: 50 mm
systems MC-P Z are particularly suitable for the system is obtained. Max. jaw opening: 6 – 204 mm
use in pallet systems. The patented segment design ensures a high
The high force and stability obviate the need for degree of precision and stability. The guiding MC-P 125 Z and ZH
pre-stamping of the workpieces. clearance is reduced to nearly zero. Jaw width: 125 mm
All essential components are made of hard- Mechanical clamping force*: 40 kN at 180 Nm
Accessories ened steel. Hydraulic clamping force*: 35 kN at 270 bar
• Clamping jaws and jaw inserts, accessories The workholding systems MC-P 100 Z / 125 Z Clamping stroke: 101 mm
for mounting, positioning and operation are already prepared for the use on zero point Max. jaw opening: 6 – 400 mm
see data sheet WS 5.450Z clamping systems. For this purpose, there are
location threads for retractable nipples at the MC-P 125 Z Compact
• Rapid change block Quintus Jaw width: 125 mm
bottom side of the housing.
see data sheet WS 5.6150 Clamping force*: 40 kN at 180 Nm
For workholding systems MC-P Z, a wide
• Hydraulic pressure generators on request Clamping stroke: 10 kN
range of clamping jaws is available (see data
sheet WS 5.450Z). Max. jaw opening: 6 – 215 mm

Consultation Versions
Application example Our experts will be pleased to advise you also MC-P Z mechanically operated
on site, and work with you to find the optimum In the mechanically-operated version, the
clamping solution. clamping force is built up with a threaded
Extensive information such as drawings and spindle. When operating, both clamping slides
CAD models are available on request. move mechanically linked to the centre of the
clamping system.
Customised versions A torque wrench is used for exact and repro-
MC-P workholding systems can also be deliv- ducible clamping force adjustment.
ered as customised versions. For example with
other lengths, height or with individual mount- MC-P ZH hydraulically operated
ing holes. In the hydraulically-operated version, the
Please contact us. clamping force is built up by an externally gen-
erated hydraulic pressure. When pressurising,
*Important note both clamping slides move mechanically linked
The specified clamping forces apply to a to the centre of the clamping system. During
clamping height (n) of 15 mm. unclamping, the clamping slides return hydrau-
For higher clamping heights, the clamping lically to the position that had been set with ad-
Workholding system MC-P Z with workpiece-specific base jaw and ­forces are reduced. justing screws for stroke limitation. Thus, a fur-
form jaw used on a 5-axis machining centre. ther unnecessary wide opening of the clamping
system is avoided.
The clamping force adjustment is made by the
n

setting of the operating pressure.

MC-P100 Z

ROEMHELD · 927 Horan Drive, Fenton, MO 63026 · Phone: (314) 386-8022 · Fax: (314) 386-8034 · [email protected]
Actual issue see www.roemheld-usa.com Subject to modifications
 Technical data • Dimensions
mechanically operated • jaw widths 40, 60 and 100 mm

MC-P 40 Z Accessory: Clamping jaw

View from below
(Fig. shows reversible step jaw 9 4581 6931)
S
SW 7
20 Stroke 80 ±0,01 M 6x7

d3
d2
g
64

52

28
MC-P40 Z

9
110 2,5 40 40 40

Accessory: Clamping jaw

MC-P 60 Z (Fig. shows reversible step jaw 9 4583 6901)
S
SW 12
30 Stroke
100 ±0,01
d2 M 8x10

d3
88

70

42
MC-P 60 Z
12

170 8 60 36 36 36 36

MC-P 100 Z

Accessory: Clamping jaw

(Fig. shows reversible step jaw 9 4585 6901)
d1: Location hole for retractable nipple
S of a zero point clamping system
S1
SW 14
50 Stroke 200 ±0,01
M 10x15

g
d1
125
115

100

70

MC-P100Z
24

260 3 100 80 80 80

All dimensions in [mm]

Series MC-P 40 Z MC-P 60 Z MC-P 100 Z

Clamping principle concentric concentric concentric
Operation mechanical mechanical mechanical
Clamping force / torque [kN/Nm] 7.5 / 23 15 / 60 25 / 90
Repetitive clamping accuracy [mm] ± 0.015 ± 0.015 ± 0.015
S* [mm] 6 – 79 6 – 150 18 – 204
S1* [mm] – – 6 – 192
d1 [mm] – – 25 +0.01 x 5 / M10 x 14
d2 [mm] 6 F7 10 F7 –
d3 [mm] M10 x 12 M10 x 11 –
g on both sides [mm] M 5 x 6 M 8 x 10 M 8 x 14
Weight without clamping jaws [kg] 1.5 4.7 17.7
Part no. without clamping jaws 9 4581 0301 9 4583 0301 9 4585 0301
* depending on the used clamping jaw

2 Actual issue see www.roemheld-usa.com ROEMHELD

WS 5.4502 / 6 -18 E Subject to modifications

 Technical data • Dimensions
mechanically operated • jaw width 125 mm

MC-P 125 Z View from below

Accessory: Clamping jaw
(Fig. shows reversible step jaw 9 4586 6901)
S d1: Location hole for retractable nipple
SW 17 of a zero point clamping system
S1

101 Stroke 200 ±0,01

M12x18

g
160
150

130

66
MC-P125 Z

d1
27
465 4,5 125 83 164 83

MC-P 125 Z Compact
Accessory: Clamping jaw
(Fig. shows reversible step jaw 9 4586 6901)

S d1: Location hole for retractable nipple

of a zero point clamping system
SW 17
S1

101 Stroke 200 ±0,01

M12x16

g
160
150

66
130
MC-P125 Z
27

d1
283 3 125 164

All dimensions in [mm]

Series MC-P 125 Z MC-P 125 Z Compact

Clamping principle concentric concentric
Operation mechanical mechanical
Clamping force / torque [kN] 40 / 180 40 / 180
Repetitive clamping accuracy [mm] ± 0.015 ± 0.015
S* [mm] 18 – 400 18 – 215
S1* [mm] 6 – 388 6 – 203
d1 [mm] 25 + 0.01 x 5 / M 10 x 18 25 + 0.01 x 5 / M 10 x 18
g on both sides [bar] M 12 x 18 M 12 x 18
Weight without clamping jaws [kg] 52.3 30.5
Part no. without clamping jaws 9 4586 0301 9 4586 0601
* depending on the used clamping jaw

ROEMHELD Actual issue see www.roemheld-usa.com 3

WS 5.4502 / 6 -18 E Subject to modifications

 Technical data • Dimensions
hydraulically operated • jaw widths 60, 100 and 125 mm

MC-P 60 ZH View from below

Accessory: Clamping jaw
(Fig. shows reversible step jaw 9 4583 6901)
Stroke limitation S

30 Stroke 150 ±0,01 M8x10

55 54
d2
g
98

80

18
MC-P60ZH

42

19
12
170 12 60 36 72 36

A: Clamping B: 10 H7 A: 10 H7
B: Unclamping

MC-P 100 ZH
Accessory: Clamping jaw
(Fig. shows reversible step jaw 9 4585 6901) d1: Location hole for retractable nipple
of a zero point clamping system
S
Stroke limitation
S1
200 ±0,01
50 Stroke
75 75 M10x15

g
125

35
115

100

70
MC-P100 ZH

35
14

d1
266 12,5 100 80 80 80

G 1/8" B: 10 H7 A: 10 H7

MC-P 125 ZH
Accessory: Clamping jaw
(Fig. shows reversible step jaw 9 4586 6901) d1: Location hole for retractable nipple
Stroke limitation of a zero point clamping system
S
400 ±0,01
S1
100 100
101 Stroke
M12x16

g
150

29
160

130
66

MC-P125 ZH

29
27

d1

465 20 125 83 164 83

G 1/4" B: 10 H7 A: 10 H7

All dimensions in [mm]

Series MC-P 60 ZH MC-P 100 ZH MC-P 125 ZH

Clamping principle concentric concentric concentric
Operation hydraulic hydraulic hydraulic
Clamping force / operating pressure [kN/bar] 10 / 320 20 / 270 35 / 270
Max. unclamping pressure [bar] 50 50 50
Max. oil volume [cm³ ] 15 51 161
Oil volume per 1 mm stroke [cm³ ] 0.5 1 1.6
Repetitive clamping accuracy [mm] ± 0.02 ± 0.02 ± 0.02
S* [mm] 6 – 150 18 – 204 18 – 400
S1* [mm] – 6 – 192 6 – 388
d1 [mm] – 25 +0.01 x 5 / M10 x 14 25 +0.01 x 5 / M10 x 14
d2 [mm] 12 F7 – –
g on both sides [mm] M 6 x 7 M 8 x 11 M 8 x 11
Weight without clamping jaws [kg] 5.4 17.4 50.5
Part no. without clamping jaws 9 4583 0401 9 4585 0401 9 4586 0401
* depending on the used clamping jaw

4 Actual issue see www.roemheld-usa.com ROEMHELD

WS 5.4502 / 6 -18 E Subject to modifications