Scribd
Upload
21 views

Summing Forssell

The document describes an 8 channel passive summing bus circuit. Each input channel consists of a 5k ohm resistor between the tip and ring connections of an XLR or TRS jack. The sleeve connections of inputs 1-7 are connected directly to chassis ground, while input 8 shows an optional 0.1uF capacitor to ground to prevent loops. Input 4 sums the signals and provides a combined output through another XLR/TRS jack. The source impedance is 600 ohms and input impedance is 5.7k ohms. The load impedance should be 10k ohms or higher.

Uploaded by

Anderson Goulart
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
21 views

Summing Forssell

The document describes an 8 channel passive summing bus circuit. Each input channel consists of a 5k ohm resistor between the tip and ring connections of an XLR or TRS jack. The sleeve connections of inputs 1-7 are connected directly to chassis ground, while input 8 shows an optional 0.1uF capacitor to ground to prevent loops. Input 4 sums the signals and provides a combined output through another XLR/TRS jack. The source impedance is 600 ohms and input impedance is 5.7k ohms. The load impedance should be 10k ohms or higher.

Uploaded by

Anderson Goulart
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

1 2 3 4 5 6

Pin 1/Sleeve Pin 1/Sleeve


Input #1
5k Input #1
5k
Pin 2/Tip Pin 2/Tip
D D
Pin 3/Ring Pin 3/Ring
XLR or TRS Jack
5k XLR or TRS Jack
Chassis Ground
Pin 1/Sleeve Pin 1/Sleeve
Input #2
5k Input #2
5k
Pin 2/Tip Pin 2/Tip

Pin 3/Ring Pin 3/Ring


XLR or TRS Jack
5k XLR or TRS Jack

Pin 1/Sleeve Pin 1/Sleeve


Input #3
5k Input #3
5k
Pin 2/Tip Pin 2/Tip

Pin 3/Ring Pin 3/Ring


XLR or TRS Jack
5k XLR or TRS Jack

C C
Pin 1/Sleeve Pin 1/Sleeve Pin 1/Sleeve Pin 1/Sleeve
Input #4
5k Input #4
5k Summed Output
Pin 2/Tip Pin 2/Tip Pin 2/Tip Pin 2/Tip
Summed Output
Pin 3/Ring Pin 3/Ring Pin 3/Ring Pin 3/Ring
XLR or TRS Jack
5k XLR or TRS Jack XLR or TRS Jack XLR or TRS Jack

Pin 1/Sleeve Pin 1/Sleeve


Input #5
5k Input #5
5k
Pin 2/Tip Pin 2/Tip

Pin 3/Ring Pin 3/Ring


XLR or TRS Jack
5k XLR or TRS Jack

Pin 1/Sleeve Pin 1/Sleeve


Input #6
5k Input #6
5k
Pin 2/Tip Pin 2/Tip

Pin 3/Ring Pin 3/Ring


B
XLR or TRS Jack
5k XLR or TRS Jack
B

Pin 1/Sleeve Pin 1/Sleeve


Input #7
5k Input #7
5k
Pin 2/Tip Pin 2/Tip

Pin 3/Ring Note.... Pin 3/Ring


XLR or TRS Jack
5k XLR or TRS Jack
To prevent ground loops, you can use a 0.1mfd
ceramic cap from pin #1/Sleeve to chassis ground,
Pin 1/Sleeve
instead of a hardwire connection. Pin 1/Sleeve
Input #8
5k Input #8
5k
Pin 2/Tip The Source impedance (looking back into the output Pin 2/Tip
connector) is appox 600 ohms with the values shown.
Pin 3/Ring Pin 3/Ring
XLR or TRS Jack
5k XLR or TRS Jack
The Input impedance for each input is appox 5.7k
ohms.

Load impedance (the input impedance of the device


A to which the output of the summing buss is attached) A
Balanced Input Summing should be 10k ohms or higher. Un-Balanced Input Summing
Title
8 Channel Passive Summing Busses
Size Number Revision
B
Date: 29-Jun-2003 Sheet of
File: C:\Website\protel database\website.ddb Drawn By:
1 2 3 4 5 6

You might also like