CyBe MORTAR 3DPRINTABLE MORTAR :

For architectural, structural, industrial, and

design 3Dconcrete printing applications

Professional 3Dconcrete printing

CyBe MORTAR Datasheet

Highlights: PRODUCT NAME:

CyBe MORTAR
• 3DPRINTABLE 3Dprintable MORTAR
Specially developed for 3Dconcrete
printing applications. DESCRIPTION:
CyBe MORTAR is a high-performance, singlepurpose
• DURABLE material. Durable in all environments, CyBe MORTAR is
non-metallic with a very low chloride and sulphate
Formulated for long life even in critical
applications. content. Use CyBe MORTAR with a 3Dconcrete printer
to produce high durability objects where low shrinkage
• STRUCTURAL is desired. CyBe MORTAR sets in 3 minutes and
For structural and non structural achieves structural strength in 1 hour.
construction components and objects.
3DCONCRETE PRINTING:
• SINGLEPURPOSE CyBe MORTAR enables to 3Dprint at speeds of max.
Usage only for 3Dconcrete printing 600 mm/s and layer heights up to 50 mm. Moreover,
with 3Dconcrete printers analysed and the timewindow to print on top of a 3Dprinted layer
approved by CyBe Construction. only takes 10 seconds.

EXCLUSIVE SUPPLIER: APPLICATIONS:

CyBe Construction B.V. Use CyBe MORTAR with 3Dconcrete printing for
Kanaalstraat 12b architectural, structural, industrial and design purposes.
5347 KM Oss
the Netherlands ENVIRONMENTAL ADVANTAGES:
Tel: +31 (0)412 669 444
Use CyBe MORTAR to reduce your carbon footprint
Web: www.CyBe.eu and lower your environmental impact. Production
E-mail: [email protected] of CyBe MORTAR emits up to 60% less CO2 than
portland cement.

CyBe Construction, the Netherlands l [email protected] l www.CyBe.eu 1/3

Technical specifications
Color concrete grey

Grain size 0 – 3 mm DIN/BS EN 933-1

Consumption approx. 1,5 kg per 1,7 s. – 5 s.

corresponds to a layer of 1m length, 40mm width and
20mm height and depends on printing speed ranging 200 – 600 mm/s

Layer thickness variable; standard 20x40mm (h x w)

depending on the selected nozzle, preliminary testing required

Setting time initial set approx. 3 min DIN/BS EN 196-3

final set approx. 5 min

Load bearing after 60 min

Compressive strength (fck) after 5h approx. 20 N/mm² DIN/BS EN 12390-13

after 1d approx. 25 N/mm² DIN/BS EN 1015-11
DIN/BS EN 12504-1
after 7d approx. 30 N/mm²
after 28d approx. 40 N/mm²

Tensile/Bond strength (fctm) after 1d fctk,// = approx. 2,4 N/mm² DIN/NEN EN 1542
Parallel to layer : // fctk,Ʇ = approx. 2,4 N/mm² CUR Aanbeveling 20
Perpendicular to layer : Ʇ
after 28d fctk,// = approx. 4 N/mm²
fctk,Ʇ = approx. 4 N/mm²

Flexural strength (fctm,fl)* after 5h approx. 4 N/mm² DIN/BS EN 1015-11

*: Identical in different orientations DIN/BS EN 13892-2
after 1d approx. 4 N/mm²
perpendicular and parallel to layer
after 7d approx. 5 N/mm²
after 28d approx. 6 N/mm²

Density (ρ) hardened approx. 2100 - 2200 kg/m³ DIN EN 12390-13, DIN EN 12390-7
DIN EN 12504-1
Flow approx. 160mm ASTM C1437-01

Air void content approx. 5,3 Vol.-% DIN/BS EN 1015-7; Method A

Static stabilized secant approx. 26.000 – 28.000 N/mm² DIN EN 12390-13; Method B
E-modulus (Ecm) DIN EN 13412

Thermal resistance 0,054 (m2* K)/W ASTM C177:10

*: At mean temperature 35 °C

(1 (2
Thermal conductivity (λ) 0,781 – 0,979 W/(m.K) DIN 52612
(1
*: At various temperatures, based : Performed on 3Dprinted specimen ASTM C177:10
on corresponding standard (2
: Performed on densified lab specimen

Specific heat capacity (c) 1,10 J/(g*K) ±0,06 Determined with Macro-DSC

Thermal expansion coefficient (αm) 15,0 * 10-6/K DIN EN 1770

Depth of water penetration 23 mm DIN EN 12390-8

pH value 12
Sulfate resistance Requirement fulfilled; V According to W. Wittekindt
According to W. Wittekindt High chemical resistance From : ZKG, Zement, Kalk, Gips - 1960

Fire classification Class A1: non-combustible DIN EN 13501-1;

acc.to EN ISO 1182 and EN ISO 1716

* With every 3Dprint variables can be attuned to the most optimal 3Dprint strategy to 3Dprint the product.
Therefore no rights can be derived from the information provided in the specifications.
* Data may be changed without notice.

CyBe Construction, the Netherlands l [email protected] l www.CyBe.eu 2/3

Implementation
STRENGTH DEVELOPMENT:
If applied under recommendations and properly
executed with curing under the advised
circumstances, the graph shown to the right is a
representation of the strength development of CyBe
MORTAR. Indicative load bearing capacity could be
achieved after already 1 hour. The structural engineer
can determine based on specific situations what the
lead-time for individual 3DCP objects is.
The graph is indicative and depends on the
circumstances and specifically designed and applied
CyBe MORTAR.
* Indicative; curve-type remains, specific values are influenced due to external
factors and specifically required material design
MINIMUM PRINTING REQUIREMENTS:
To enable 3Dconcrete printing a set of minimum · Water supply min. 300 L/h, temperature min. 13 °C – max. 20 °C (55 °F – 68 °F)
requirements on the construction site is needed. The · Water supply min. 50 L/h, for curing immediately after 3Dconcrete printing
following specific requirements are needed but · Controlled workspace temperature min. 5 °C – max. 30 °C
depend on specific circumstances and therefore are · Waste containers for mortar packaging, plastic and hardened concrete
not limited to : · Additional requirements will be specified depending on specific project and
· Supply of clean tap water, similar to water construction-site requirements
quality in the Netherlands
· Short and long term specified storage facilities
for 3DCP equipment and mortar pallets.

Application, storage and liability

3DPRINTING: WARNING: DO NOT BREATHE DUST,
The use of a CyBe 3Dprinter is recommended. Organize AVOID CONTACT WITH SKIN AND EYES
work so that all personnel and equipment are in place
before 3Dprinting. Use clean potable water. The needed Use material in well-ventilated areas only. Exposure to cement dust may irritate
quantity of water dependeds on the 3Dprint strategy. eyes, nose, throat, and the upper respiratory system/lungs. Seek medical
treatment if you experience difficulty breathing while using this product. Eat and
PLACEMENT: drink only in dust-free areas to avoid ingesting cement dust. Skin contact with dry
CyBe MORTAR shall only be applied using a 3Dconcrete material or wet mixtures may result in moderate irritation to thickening/cracking
printer. Organize work so that all personnel and of skin to severe skin damage from chemical burns. If irritation or burning
equipment are ready before 3Dconcrete printing. occurs, seek medical treatment. Protect eyes with goggles or safety glasses with
3Dprint, consolidate and screed quickly to allow for side shields. Cover skin with protective clothing. Use chemical resistant gloves
maximum finishing time. Use a method of consolidation and waterproof boots. in case of skin contact with cement dust, immediately
that eliminates air voids. Do not wait for bleed water; wash off dust with soap and water to avoid skin damage. Wash skin areas exposed
apply final finish as soon as possible. CyBe MORTAR may to wet concrete with cold, running water as soon as possible. in case of eye
be troweled, floated or broom finished. Do not install on contact with cement dust, flush immediately and repeatedly with clean water and
frozen surfaces. CyBe MORTAR may be applied in consult a physician. if wet concrete splashes into eyes, rinse eyes with clean water
temperatures ranging from 5°C to 30°C. for at least 15 minutes and contact a hospital for possible further treatment.

CURING: LIMITED WARRANTY

Water cures CyBe MORTAR installations by keeping CyBe Construction warrants its materials to be of good quality and at its option,
exposed surfaces wet for a minimum of 1 hour. Begin within 6 months from date of sale, will replace material proven detective or
curing as soon as the surface starts to lose its moist refund purchase price therefor, and such replacement or refund shall be the limit
sheen. When experiencing extended setting time due to of CyBe’s responsibility. Except for the foregoing, all warranties expressed or
cold temperature, longer curing times may be implier, including merchantability and fitness are excluded. CyBe shall not be
required. The objective of water curing shall be to liable for any consequential, incidental, or special damages arising directly from
maintain a continuously wet surface until the product the use of the material.
has achieved sufficient strength.
USER RESPONSIBILITY
YIELD & PACKAGING: Before using CyBe MORTAR, read current technical data sheet and 3Dprinter
CyBe MORTAR is available in 55-lb (25-kg) sizes. One 55- manual. It is the user’s responsibility to review instructions and warnings for any
lb (25-kg) bag of CyBe MORTAR will yield approximately CyBe MORTAR product in current technical data sheet prior to use.
14 liter.
* With every 3Dprint variables can be attuned to the most optimal 3Dprint
SHELF LIFE: strategy to 3Dprint the product. Therefore no rights can be derived from the
6 Months when stored in cool, dry humidity stable information provided in the specifications.
conditions out of direct sunlight. * Data may be changed without notice.

CyBe Construction, the Netherlands l [email protected] l www.CyBe.eu 3/3