Angle (Hot Rolled)

For uses that requires one leg of the angle to be longer than the other, the unequal Angle/L-
Angle can be used. If the steel angle's requires the angle of degree other than 90 degrees,
a V-Angle will be more suitable.

For this type of product, our company produces two variations, the Unequal Angle/L-Angle
and the Equal Angle. There are certain variations in the steel angles depending on its basic
construction.

One of hot rolled product under our range is the Angle Beam. Steel Angle is an important
structural steel section for the manufacture of communication tower and power towers, as
well as workshops and other engineering projects. It can be composed into different bearing
components with different structures and it can also be used as joint piece between the
components.

Gunung Garuda's Angles are hot rolled and are produced by rolling pre-heated blooms into
an Angle shape. Our angle bars are manufactured under strict quality controls to ensure
consistency and conformity to regional and international standards.

Grades and sizes other than shown on the table may also be available depending upon
section and quantity requirements.

Size Range : 50x50 to 250x250

Standard Length : 6m & 12m
Thickness Range : 5mm to 35mm
Annual Capacity : > 60.000 MT/Y
Standards : JIS G 3101 SS400 (Mild Steel)
JIS G 3101 SS540 (High Strength)
EQUAL ANGLE Metric Size

REMARKS

kg/6m kg/12m
40 x 40 4 4.5 2 3.080 2.42 14.52 29 1.090 3.530 5.60 1.460 1.230 1.55 0.79 1.210
22.62 45
r2
26.58 53
27.5 55 H
2
5.42 32.5 65 H 90
t
30 60 r1
r2
35.5 71

t
38.5 77 B
41 82 2
B
43.9 88
57.6 115
80 160
64 128
89.5 179
88 176 Y
119.5 239
V U

ex
130 259
iv
107.4 215

ix

iu
140.5 281 X X

iu
Cx
iv
164 328
202 403 U Cy iy
V
251.5 503 ey

191 382
236.5 473
272 544
358 716
442 883
562 1124
768 1536

NOTE : Non standard sizes are available upon request and subject to minimum quantity

Mainstream | Angle 07
UNEQUAL ANGLE Metric Size

REMARKS
tan
kg/6m kg/12m
90 x 75 9 8.5 6 14.01 11.0 66.0 132 2.75 2.00 109 68.1 143 34.1 2.78 2.20 3.19 1.56 0.676 17.4 12.4
100 x 75 7 10 5 11.87 9.32 55.9 112 3.06 1.83 118 56.9 144 30.8 3.15 2.19 3.49 1.61 0.548 17.0 10.0

A
2
100 x 75 10 10 7 16.50 13.0 78.0 156 3.17 1.94 159 76.1 194 41.3 3.11 2.15 3.43 1.58 0.543 23.3 13.7 t

A
90o
125 x 75 7 10 5 13.62 10.7 64.2 128 4.10 1.64 219 60.4 243 36.4 4.01 2.11 4.23 1.64 0.362 26.1 10.3 r1
r2

125 x 75 10 10 7 19.00 14.9 89.4 179 4.22 1.75 299 80.8 330 49.0 3.96 2.06 4.17 1.61 0.357 36.1 14.1 t
B
2
B
125 x 75 13 10 7 24.31 19.1 114.6 229 4.35 1.87 376 101 415 61.9 3.93 2.04 4.13 1.60 0.352 46.1 17.9
125 x 90 10 10 7 20.50 16.1 96.6 193 3.95 2.22 318 138 380 76.2 3.94 2.59 4.30 1.93 0.505 37.2 20.3
Y
125 x 90 13 10 7 26.26 20.6 123.6 247 4.07 2.34 401 173 477 96.3 3.91 2.57 4.26 1.91 0.501 47.5 25.9
150 x 90 9 12 6 20.94 16.4 98.4 197 4.95 1.99 485 133 537 80.4 4.81 2.52 5.06 1.96 0.361 48.2 19.0 V

ex
U

150 x 90 12 12 8.5 27.36 21.5 129.0 258 5.07 2.10 619 167 685 102 4.76 2.47 5.00 1.93 0.357 62.3 24.3

ix

iv
iu
150 x 100 9 12 6 21.84 17.1 102.6 205 4.76 2.30 502 181 579 104 4.79 2.88 5.15 2.18 0.439 49.1 23.5 X X

iu
ev

Cx

iv
U
150 x 100 12 12 8.5 28.56 22.4 134.4 269 4.88 2.41 642 228 738 132 4.74 2.83 5.09 2.15 0.435 63.4 30.1 Cy iy
ey
150 x 100 15 12 8.5 35.25 27.7 166.2 332 5.00 2.53 782 276 897 161 4.71 2.80 5.04 2.14 0.431 78.2 37.0 Y V

NOTE : Non standard sizes are available upon request and subject to minimum quantity
Not Available

08 Mainstream | Angle
DIMENSIONAL TOLERANCE Metric Size | JIS 3192 / TIS 1227-194

DIMENSION TOLERANCE REMARKS

Under 50 in depth ± 1.5

Leg Length 50 or over to and excl. 100 ± 2.0
(A or B) 100 or over to and excl. 200 ± 3.0
t1
200 or over ± 4.0

t2
For Leg Length A Under 6.3 ± 0.6
(B for T Section)
6.3 or over to and excl.10 ± 0.7 B
or under 130 in depth 2
10 or over to and excl.16 ± 0.8 B
16 or over ± 1.0
Thickness t,
t 1, t 2 For Leg Length A Under 6.3 ± 0.7
(B for T Section)
or under 130 or over in depth 6.3 or over to and excl.10 ± 0.8
10 or over to and excl.16 ± 1.0 t1
16 or over to and excl.25 ± 1.2
25 or over ± 1.5

7m or under + 40

t2
-0

Over 7m Add 5mm to the plus side B

Length 2
tolerance given in the above B
column for every 1m. Increase
in length or its fraction

I Section 2.0 % or under of width B

90 90
0 0

Out of 2.5 % or under of width of T

Sections excluding I and T sections T
Square (T) flange B (or leg length)

I and T Sections 0.20% or under of length To be applied to bend such

Bend as sweep and camber
Sections excluding I and T sections 0.30% or under of length
CHEMICAL COMPOSITION According JIS G 3101, G 3106

CHEMICAL COMPOSITION (%)

SYMBOL OF GRADE
C Si Mn P S

SS 400, 490 0.050 max 0.050 max

SS 540 0.3 max 1.60 max 0.040 max 0.040 max

50 mm or under in thickness 0.23 max 2.5 x c

SM 400 A
over 50 mm, up to and incl. 200 mm in thickness 0.25 max min (1) 0.035 max 0.035 max
50 mm or under in thickness 0.20 max
SM 400 B 0.35 max 0.60 -1.40 0.035 max 0.035 max
over 50 mm, up to and incl. 200 mm in thickness 0.22 max

SM 400 C 100 mm or under in thickness 0.18 max 0.35 max 1.40 max 0.035 max 0.035 max

50 mm or under in thickness 0.20 max

SM 490 A 0.55 max 1.60 max 0.035 max 0.035 max
over 50 mm, up to and incl. 200 mm in thickness 0.22 max
50 mm or under in thickness 0.18 max
SM 490 B 0.55 max 1.60 max 0.035 max 0.035 max
over 50 mm, up to and incl. 200 mm in thickness 0.20 max

SM 490 C 100 mm or under in thickness 0.18 max 0.55 max 1.60 max 0.035 max 0.035 max

SM 490 YA
100 mm or under in thickness 0.20 max 0.55 max 1.60 max 0.035 max 0.035 max
SM 490 YB
SM 520 B
100 mm or under in thickness 0.20 max 0.55 max 1.60 max 0.035 max 0.035 max
SM 520 C

SM 570 100 mm or under in thickness 0.18 max 0.55 max 1.60 max 0.035 max 0.035 max

Note: (1) The value of carbon here in is the actual cast analysis value
CORRESPONDING SPECIFICATION Metric Size

CLASSIFIED BY TENSILE STRENGTH SPECIFICA TIONS

TYPE OF MA TERIAL Tensile strength Special
Class (N/mm 2) specification JIS ASTM BS 4360 DIN

General Structure 400 G 3101 SS 400 A 36 Gr. 43A St 33

490 G 3101 SS 490 Gr. 50A St 50-2
G 3106 SM 400A A 572 Gr. 42 Gr. 43B
Charpy impact test G 3106 SM 400B,C Gr. 43C St 37-2
400 RSt 37-2
Charpy impact test Gr. 43D
for low temperature
G 3106 SM 490A Gr. 43DD
Welded Structure 490
Charpy impact test G 3106 SM 490B, C
G 3106 SM 490 YA A 572 Gr. 42 Gr. 50B
Charpy impact test G 3106 SM 490 YB, Gr. 50C St 52-3
490
SM 520 B, C
(High yield point)
Charpy impact test Gr. 50D
for low temperature
 EQUAL ANGLE
PT. GUNUNG GARUDA
(HOT ROLLED)

METRIC SIZE

r2
STANDARD INFORMATIVE REFERENCE
SECTION
SECTIONAL UNIT CENTER GEOMETRICAL MOMENT RADIUS OF GYRATION MODULUS H
AREA OF
DIMENSIONS WEIGHT OF INERTIA OF AREA OF SECTION 2
GRAVITY
90
H x B t r 1 r2 A Cx = Cy Ix = Iy Max Iu Min Iv ix = iy Max iu Min iv Zx = Zy H
t
mm x mm mm mm mm cm2 kg/m cm cm4 cm4 cm4 cm cm cm cm3

r1
25 x 25 3 4 2 1.427 1.12 0.719 0.797 1.26 0.332 0.747 0.94 0.48 0.448

r2
30 x 30 3 4 2 1.727 1.36 0.844 1.420 2.26 0.590 0.908 1.14 0.58 0.661

t
40 x 40 3 4.5 2 2.336 1.83 1.090 3.530 5.60 1.460 1.230 1.55 0.79 1.210
40 x 40 4 4.5 2 2.336 1.83 1.090 3.530 5.60 1.460 1.230 1.55 0.79 1.210
B
40 x 40 5 4.5 3 3.755 2.95 1.170 5.420 8.59 2.250 1.200 1.51 0.77 1.910
2
45 x 45 5 6.5 3 4.302 3.38 1.280 7.910 12.50 3.290 1.360 1.71 0.87 2.460 B
45 x 45 4 6.5 3 3.492 2.74 1.240 6.500 10.30 2.700 1.360 1.72 0.88 2.000
50 x 50 4 6.5 3 3.892 3.06 1.370 9.060 14.40 3.760 1.530 1.92 0.98 2.490
50 x 50 5 6.5 3 4.802 3.77 1.410 11.100 17.50 4.580 1.520 1.91 0.98 3.080
50 x 50 6 6.5 4.5 5.644 4.43 1.440 12.600 20.00 5.230 1.500 1.88 0.96 3.550 Y
60 x 60 4 6.5 3 4.692 3.68 1.610 16.000 25.40 6.620 1.850 2.33 1.19 3.660
60 x 60 5 6.5 3 5.802 4.55 1.660 19.600 31.20 8.090 1.840 2.32 1.18 4.520
V U

ex
60 x 60 6 8 4 6.910 5.40 1.700 22.790 36.16 9.420 1.820 2.29 1.17 5.280
65 x 65 5 8.5 3 6.367 5.00 1.770 25.300 40.10 10.500 1.990 2.51 1.28 5.350

iv
ix
65 x 65 6 8.5 4 7.527 5.91 1.810 29.400 46.60 12.200 1.980 2.49 1.27 6.260

iu
65 x 65 8 8.5 6 9.761 7.66 1.880 36.800 58.30 15.300 1.940 2.44 1.25 7.960 X X

Cx
70 x 70 6 8.5 4 8.127 6.38 1.930 37.100 58.90 15.300 2.140 2.69 1.37 7.330

iu
iv
75 x 75 6 8.5 4 8.727 6.85 2.060 46.100 73.20 19.000 2.300 2.90 1.48 8.470
75 x 75 9 8.5 6 12.690 9.96 2.170 64.400 102.00 26.700 2.250 2.84 1.45 21.100 Cy iy
75 x 75 12 8.5 6 16.560 13.00 2.290 81.900 129.00 34.500 2.220 2.79 1.44 15.700
U V
80 x 80 6 8.5 4 9.230 7.32 2.180 56.400 89.60 23.200 2.460 3.10 1.58 9.700 Y ey
90 x 90 6 10 5 10.550 8.28 2.420 80.700 128.00 33.400 2.770 3.48 1.78 12.300
90 x 90 7 10 5 12.220 9.59 2.460 93.000 148.00 38.300 2.760 3.48 1.77 14.200
90 x 90 10 10 7 17.000 13.30 2.570 125.000 199.00 51.700 2.710 3.42 1.74 19.500
90 x 90 13 10 7 21.710 17.00 2.690 156.000 248.00 65.300 2.680 3.38 1.73 24.800
100 x 100 7 10 5 13.620 10.70 2.710 129.000 205.00 53.200 3.080 3.88 1.98 17.700
100 x 100 13 10 7 24.310 19.10 2.940 220.000 348.00 91.100 3.000 3.78 1.94 31.100
100 x 100 10 10 7 19.000 14.90 2.820 175.000 278.00 72.000 3.040 3.83 1.95 24.400
120 x 120 8 12 5 18.760 14.70 3.240 258.000 410.00 106.000 3.710 4.67 2.38 29.500
120 x 120 11 13 6.5 25.370 19.90 3.300 340.000 541.00 140.000 3.660 4.62 2.35 39.360
120 x 120 12 13 6.5 27.540 21.60 3.400 367.000 583.00 151.000 3.650 4.60 2.35 42.680
130 x 130 9 12 6 22.740 17.90 3.530 366.000 583.00 150.000 4.010 5.06 2.57 38.700
HEAD OFFICE & FACTORY 130 x 130 15 12 8.5 36.750 28.80 3.760 568.000 902.00 234.000 3.930 4.95 2.53 41.600
Jl. Imam Bonjol 4, Warung Bongkok, 130 x 130 12 12 8.5 29.760 23.40 3.640 467.000 743.00 192.000 3.960 5.00 2.54 49.900
Sukadanau, Cikarang Barat, 150 x 150 12 14 7 34.770 27.30 4.140 740.000 1,180.00 304.000 4.610 5.82 2.96 68.100
Bekasi 17520, West Java, INDONESIA 150 x 150 15 14 10 42.740 33.60 4.240 888.000 1,410.00 365.000 4.560 5.75 2.92 82.600
150 x 150 19 14 10 53.380 41.90 4.400 1,090.000 1,730.00 451.000 4.520 5.69 2.91 103.000
Sales Department
175 x 175 12 15 11 40.520 31.80 4.730 1,170.000 1,860.00 480.000 5.380 6.78 3.44 91.800
Phone DID : (62-21) 898 38 161 - 167 175 x 175 15 15 11 50.210 39.40 4.850 1,440.000 2,290.00 589.000 5.350 6.75 3.48 114.000
Phone Flexy : 200 x 200 15 17 12 57.750 45.30 5.460 2,180.000 3,470.00 891.000 6.140 7.75 3.93 150.000
(021) 7085 3164 - 165 200 x 200 20 17 12 76.000 59.70 5.670 2,820.000 4,490.00 1,160.000 6.090 7.68 3.90 197.000
(021) 7085 3169 200 x 200 25 17 12 93.750 73.60 5.860 3,420.000 5,420.00 1,410.000 6.040 7.61 3.88 242.000
Fax. : (62-21) 8910 - 7711, 250 x 250 35 24 18 162.600 128.00 7.450 9,110.000 14,400.00 3,790.000 7.490 9.42 4.83 519.000
250 x 250 25 24 12 119.400 93.70 7.100 6,950.000 11,000.00 2,860.000 7.630 9.62 4.89 388.000
(62-21) 8900-555 / 976 / 977 continue .......>>
e-mail : [email protected] NOTE : Can be supplied by our mill
[email protected]
www.grdsteel.com
 EQUAL ANGLE
PT. GUNUNG GARUDA
(HOT ROLLED)

DIMENSIONAL TOLERANCE
JIS G3192/TIS 1227-194 METRIC SIZE CHEMICAL COMPOSITION ACCORDING JIS G 3101, G 3106
SYMBOL CHEMICAL COMPOSITION (%)
DIMENSION TOLERANCE REMARK OF
GRADE C Si Mn P S
Under 50 in depth 1.5 SS 400, 490 0.050 max 0.050 max
Leg length 50 or over to and excl. 100 2.0

A
2

A
2
0.3 max 1.60 max 0.040 max 0.040 max
(A or B) 100 or over to and excl. 200 3.0 t SS 540

A
t1 50 mm or under in thickness 0.23 max 2.5 x c
4.0 SM 400 A
200 or over

t
over 50 mm, up to and incl. 200 mm in thickness 0.25 max min (1) 0.035 max 0.035 max

Under 100 1.5 B 50 mm or under in thickness 0.20 max

2 SM 400 B over 50 mm, up to and incl. 200 mm in thickness 0.22 max 0.35 max 0.60 -1.40 0.035 max 0.035 max

t2
B
100 or over to and excl. 200 2.0
Dept (H) B
SM 400 C 100 mm or under in thickness 0.18 max 0.35 max 1.40 max 0.035 max 0.035 max
200 or over to and excl. 400 3.0 2
B 50 mm or under in thickness 0.20 max
400 or over 4.0 SM 490 A 0.55 max 1.60 max 0.035 max 0.035 max

t2
over 50 mm, up to and incl. 200 mm in thickness 0.22 max

For leg length Under 6.3 0.6 SM 490 B

50 mm or under in thickness 0.18 max
0.20 max
over 50 mm, up to and incl. 200 mm in thickness 0.55 max 1.60 max 0.035 max 0.035 max

H
2
A (B for T 6.3 or over

H
B-t1 B-t1 SM 490 C 100 mm or under in thickness 0.18 max 0.55 max 1.60 max 0.035 max 0.035 max
Thickness Section) or to and excl. 10 0.7 4 4 t1

t, t1 , t2 under 130 10 or over to

SM 490 YA 100 mm or under in thickness 0.20 max 0.55 max 1.60 max 0.035 max 0.035 max
SM 490 YB

t2
in depth and excl.16 0.8 SM 520 B
100 mm or under in thickness 0.20 max 0.55 max 1.60 max 0.035 max 0.035 max
SM 520 C
16 or over 1.0 B
SM 570 100 mm or under in thickness 0.18 max 0.55 max 1.60 max 0.035 max 0.035 max
Under 6.3 0.7
For leg length
6.3 or over to Note: (1) The value of carbon here in is the actual cast analysis value

t2
H
A (B for T

2
and excl. 10 0.8 B-t1 B-t1
Section) :

H
2 2
10 or over to
130 or over t1 MECHANICAL PROPERTIES METRIC SIZE
and excl. 16 1.0
in depth

t2
16 or over to Yield Point Elongation, %
and excl. 25 1.2
B N/mm2 Tensile Strength
min
Classification N/mm2

A
Thickness (mm)

2
25 or order 1.5 Thickness (mm)
t
16 or under over 16 5 or under 5 to 16 over 16

A
40
7 m or under
0 JIS G3101 SS400 245 235 400-510 21 17 21

Add 5 mm to the plus side B JIS G3101 sS540 400 390 min. 540 16 13 17
Length B
tolerance given in the above 4
JIS G3101 Ss490 285 275 490-610 19 15 19
over 7 m
column for every 1 m. r2
t2
H

r1 JIS G3106 SM400, A,B,C 245 235 400-510 23 18 22

Increase in length or its fraction. t1
JIS G3106 SM490 A,B,C 325 315 490-610 22 17 21

T
I Section 2.0% or under of width B
T

Out of JIS G3106 SM490 YA,YB 365 355 490-610 19 15 19

Sections excluding I 2.5% or under of width of 900 900
Square (T)
T

365 355 520-640 19 15 19

T

JIS G3106 SM520 B,C

and T sections flange B (or leg length)
T

JIS G3106 SM 570 460 450 570-720 19 19 26

I and T sections 0.20% or under of length To be applied to bend such
Bend Sections excluding I 0.30% or under of length as sweep and camber.
and T sections
Web-off- 300 or under in T Section 3.0 b1 - b2
center (S) width B S=
2
b1 b2

www.grdsteel.com
Angle Shape
Product Specifications
Hot Rolled

JIS 3192 Metric Size

Standard Section Informative Reference
Sectional Area Unit Weight Center of Modulus of
Geometrical Moment of Inertia Radius of Gyration of Area
Dimensions Gravity Section
H x B t r1 r2 A Cx = Cy Ix = Iy Max Iu Min Iv Ix = Iy Max Iu Min Iv Zx = Zy
mm x mm mm mm mm cm2 Kg/m cm cm 4
cm 4
cm 4
cm cm cm cm3
25 x 25 3 4 2 1.427 1.12 0.719 0.797 1.26 0.332 0.747 0.94 0.48 0.448
30 x 30 3 4 2 1.727 1.36 0.844 1.42 2.26 0.59 0.908 1.14 0.58 0.661
40 x 40 3 4.5 2 2.336 1.83 1.09 3.53 5.6 1.46 1.23 1.55 0.79 1.21
40 x 40 4 4.5 2 2.336 1.83 1.09 3.53 5.6 1.46 1.23 1.55 0.79 1.21
40 x 40 5 4.5 3 3.755 2.95 1.17 5.42 8.59 2.25 1.2 1.51 0.77 1.91
45 x 45 5 6.5 3 4.302 3.38 1.28 7.91 12.5 3.29 1.36 1.71 0.87 2.46
45 x 45 4 6.5 3 3.492 2.74 1.24 6.5 10.3 2.7 1.36 1.72 0.88 2
50 x 50 4 6.5 3 3.892 3.06 1.37 9.06 14.4 3.76 1.53 1.92 0.98 2.49
50 x 50 5 6.5 3 4.802 3.77 1.41 11.1 17.5 4.58 1.52 1.91 0.98 3.08
50 x 50 6 6.5 4.5 5.644 4.43 1.44 12.6 20 5.23 1.5 1.88 0.96 3.55
60 x 60 4 6.5 3 4.692 3.68 1.61 16 25.4 6.62 1.85 2.33 1.19 3.66
60 x 60 5 6.5 3 5.802 4.55 1.66 19.6 31.2 8.09 1.84 2.32 1.18 4.52
60 x 60 6 8 4 6.91 5.4 1.7 22.79 36.16 9.42 1.82 2.29 1.17 5.28
65 x 65 5 8.5 3 6.367 5 1.77 25.3 40.1 10.5 1.99 2.51 1.28 5.35
65 x 65 6 8.5 4 7.527 5.91 1.81 29.4 46.6 12.2 1.98 2.49 1.27 6.26
65 x 65 8 8.5 6 9.761 7.66 1.88 36.8 58.3 15.3 1.94 2.44 1.25 7.96
70 x 70 6 8.5 4 8.127 6.38 1.93 37.1 58.9 15.3 2.14 2.69 1.37 7.33
75 x 75 6 8.5 4 8.727 6.85 2.06 46.1 73.2 19 2.3 2.9 1.48 8.47
75 x 75 9 8.5 6 12.69 9.96 2.17 64.4 102 26.7 2.25 2.84 1.45 21.1
75 x 75 12 8.5 6 16.56 13 2.29 81.9 129 34.5 2.22 2.79 1.44 15.7
80 x 80 6 8.5 4 9.23 7.32 2.18 56.4 89.6 23.2 2.46 3.1 1.58 9.7
90 x 90 6 10 5 10.55 8.28 2.42 80.7 128 33.4 2.77 3.48 1.78 12.3
90 x 90 7 10 5 12.22 9.59 2.46 93 148 38.3 2.76 3.48 1.77 14.2
90 x 90 10 10 7 17 13.3 2.57 125 199 51.7 2.71 3.42 1.74 19.5
90 x 90 13 10 7 21.71 17 2.69 156 248 65.3 2.68 3.38 1.73 24.8
100 x 100 7 10 5 13.62 10.7 2.71 129 205 53.2 3.08 3.88 1.98 17.7
100 x 100 13 10 7 24.31 19.1 2.94 220 348 91.1 3 3.78 1.94 31.1
100 x 100 10 10 7 19 14.9 2.82 175 278 72 3.04 3.83 1.95 24.4
120 x 120 8 12 5 18.76 14.7 3.24 258 410 106 3.71 4.67 2.38 29.5
120 x 120 11 13 6.5 25.37 19.9 3.3 340 541 140 3.66 4.62 2.35 39.36
120 x 120 12 13 6.5 27.54 21.6 3.4 367 583 151 3.65 4.6 2.35 42.68
130 x 130 9 12 6 22.74 17.9 3.53 366 583 150 4.01 5.06 2.57 38.7
130 x 130 12 12 8.5 29.76 23.4 3.64 467 743 192 3.96 5 2.54 49.9
130 x 130 15 12 8.5 36.75 28.8 3.76 568 902 234 3.93 4.95 2.53 41.6
150 x 150 12 14 7 34.77 27.3 4.14 740 1180 304 4.61 5.82 2.96 68.1
150 x 150 15 14 10 42.74 33.6 4.24 888 1410 365 4.56 5.75 2.92 82.6
150 x 150 19 14 10 53.38 41.9 4.4 1090 1730 451 4.52 5.69 2.91 103
175 x 175 12 15 11 40.52 31.8 4.73 1170 1860 480 5.38 6.78 3.44 91.8
175 x 175 15 15 11 50.21 39.4 4.85 1440 2290 589 5.35 6.75 3.48 114
200 x 200 15 17 12 57.75 45.3 5.46 2180 3470 891 6.14 7.75 3.93 150
200 x 200 20 17 12 76 59.7 5.67 2820 4490 1160 6.09 7.68 3.9 197
200 x 200 25 17 12 93.75 73.6 5.86 3420 5420 1410 6.04 7.61 3.88 242
250 x 250 25 24 12 119.4 93.7 7.1 6950 11000 2860 7.63 9.62 4.89 388
250 x 250 35 24 18 162.6 128 7.45 9110 14400 3790 7.49 9.42 4.83 519
Angle Shape
Chemical Composition

According JIS G 3101, G 3106

Symbol
Chemical Composition
Of
Grade C Si Mn P S
SS 400, 490 - - - 0.050 max 0.050 max
SS 540 0.3 max - 1.60 max 0.040 max 0.040 max
50mm or under in thickness 0.23 max 2.5 x c
SM 400 A - 0.035 max 0.035 max
Over 50 mm, up to and incl. 200mm in thickness 0.25 max min (1)
50mm or under in thickness 0.20 max
SM 400 B 0.35 max 0.6 - 1.40 0.035 max 0.035 max
Over 50 mm, up to and incl. 200mm in thickness 0.22 max
SM 400 C 100mm or under in thickness 0.18 max 0.35 max 1.40 max 0.035 max 0.035 max
50mm or under in thickness 0.20 max
SM 490 A 0.55 max 1.60 max 0.035 max 0.035 max
Over 50 mm, up to and incl. 200mm in thickness 0.22 max
50mm or under in thickness 0.18 max
SM 490 B 0.55 max 1.60 max 0.035 max 0.035 max
Over 50 mm, up to and incl. 200mm in thickness 0.20 max
SM 490 C 100mm or under in thickness 0.18 max 0.55 max 1.60 max 0.035 max 0.035 max
SM 490 YA
100mm or under in thickness 0.20 max 0.55 max 1.60 max 0.035 max 0.035 max
SM 490 YB
SM 520 B
100mm or under in thickness 0.20 max 0.55 max 1.60 max 0.035 max 0.035 max
SM 520 C
SM 570 100mm or under in thickness 0.18 max 0.55 max 1.60 max 0.035 max 0.035 max
Angle Shape
Corresponding Specification

Metric Size
Classified By Tensile Strength Specifications
Type of Material Tensile Strength Special
Class Specification JIS ASTM BS 4360 DIN
(N/mm2)
400 - G 3101 SS 400 A 36 Gr. 43 A St 33
General Structure
490 - G 3101 SS 490 - Gr. 50 A St 50-2
- G 3106 SM 400 A A 572 Gr. 42 Gr. 43 B -
Charpy impact St 37-2
G 3106 SM 400 B, C - Gr. 43 C
test RSt 37-2
400
Charpy impact
test for low - - Gr. 43 D -
temperature
- G 3106 SM 490 A - Gr. 43 DD -
Welded Structure 490 Charpy impact
G 3106 SM 490 B, C - - -
test
- G 3106 SM 490 YA A 572 Gr. 42 Gr. 50 B -
Charpy impact G 3106 SM 490 B, C
- Gr. 50 C St 52-3
490 test SM 520 B, C
(High Yield Charpy impact
Point) test for low - - Gr. 50 D -
temperature
Angle Shape
Mechanical Properties

Metric Size
Yield Point
2 Elongation, %
N/mm Tensile Strength
Classification
Thickness (mm) N/mm2 Thickness (mm)
16 or under over 16 5 or under 5 to 16 over 16
JIS G 3101 SS400 245 235 400 - 510 21 17 21
JIS G 3101 SS540 400 390 min 540 16 13 17
JIS G 3101 SS490 285 275 490 - 610 19 15 19
JIS G 3106 SM400 A, B, C 245 235 400 - 510 23 18 22
JIS G 3106 SM490 A, B, C 325 315 490 - 610 22 17 21
JIS G 3106 SM490 YA, YB 365 355 490 - 610 19 15 19
JIS G 3106 SM520 B, C 365 355 520 - 640 19 15 19
JIS G 3106 SM570 460 450 570 - 720 19 19 26
Angle Shape
Dimensional Tolerance

JIS G3192/ TIS 1227-194 Metric Size

Dimensional Tolerance Remark

Under 50 in depth + 1.5

Leg Length 50 or over to and excl. 100 + 2.0
(A or B) 100 or over to and excl. 200 + 3.0
200 or over + 4.0
Under 6.3 + 0.6
6.3 or over to and
For Leg Length A (B + 0.7

t
excl.10
for T Section) or
10 or over to and B
under 130 in depth + 0.8 2
excl.16 B
16 or over + 1.0
Thickness t, Under 6.3 + 0.7
t1 , t 2 6.3 or over to and
+ 0.8
For Leg Length A (B excl.10
for T Section) or 10 or over to and

A
2
+ 1.0
under 130 or over in excl.16
depth 16 or over to and t1
+ 1.2
excl.25
25 or over + 1.5
+ 40
7m or under

t2
-0
Add 5mm to the plus side B
Length 2
tolerance given in the above
Over 7m B
column for every 1m. Increase
in length or its fraction

I Section 2.0 % or under of width B

Out of 90
0 0
90
Square (T) 2.5 % or under of width of T
T

Sections excluding I and T sections

flange B (or leg length)

I and T Sections 0.20% or under of length

To be applied to bend such
Bend
as sweep and camber
Sections excluding I and T sections 0.30% or under of length
Angle Shape
Table Weight

Weight
SIZE
Kg/m Kg/6m Kg/12m
Equal Angle (Hot Rolled)
L 45 x 45 x 4 2.74 16.5 33
L 50 x 50 x 4 3.06 18.5 37
L 50 x 50 x 5 3.77 22.62 45.24
L 60 x 60 x 5 4.55 27.5 55
L 60 x 60 x 6 5.42 32.5 65
L 65 x 65 x 5 5 30 60
L 65 x 65 x 6 5.91 35.5 71
L 70 x 70 x 6 6.38 38.5 77
L 70 x 70 x 7 7.38 44.5 89
L 75 x 75 x 6 6.85 41 82
L 90 x 90 x 6 8.28 49.5 99
L 90 x 90 x 7 9.6 58 115
L 90 x 90 x 8 10.8 65 130
L 90 x 90 x 9 12.2 73 146
L 90 x 90 x 10 13.3 80 160
L 90 x 90 x 13 17 102 204
L 100 x 100 x 7 10.7 64 128
L 100 x 100 x 8 12.1 73 146
L 100 x 100 x 9 13.5 81 162
L 100 x 100 x 10 14.9 89.5 179
L 100 x 100 x 12 17.8 107 214
L 100 x 100 x 13 19.1 114.6 229
L 120 x 120 x 8 14.7 88 176
L 120 x 120 x 10 18.2 109 218
L 120 x 120 x 11 19.9 119.5 239
L 120 x 120 x 12 21.6 130 260
L 130 x 130 x 9 17.9 107.5 215
L 130 x 130 x 10 19.7 118 236
L 130 x 130 x 12 23.4 140.5 281
L 150 x 150 x 10 23 138 276
L 150 x 150 x 12 27.3 164 328
L 150 x 150 x 15 33.6 202 404
L 175 x 175 x 12 31.8 191 382
L 175 x 175 x 15 39.4 236.5 473
L 180 x 180 x 14 38 228 456
L 200 x 200 x 15 45.3 272 544
L 200 x 200 x 20 59.7 358 716
L 200 x 200 x 25 73.6 442 884
L 250 x 250 x 25 93.7 562 1124
L 250 x 250 x 35 128 768 1536
Unequal Angle (Hot Rolled)
L 125 x 75 x 8 12.2 73 146
L 125 x 75 x 9 13.49 81 162
L 125 x 75 x 10 14.9 89 178
L 150 x 90 x 9 16.4 98.5 197
L 150 x 90 x 10 18.1 109 218
L 150 x 90 x 12 21.6 129.5 259