Scribd
Upload
61 views

Operator Manual-E4402-Distance To Fault Accessory Kit 90012

Agilent ESA Spectrum Analyser

Uploaded by

István Bujáki
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
61 views

Operator Manual-E4402-Distance To Fault Accessory Kit 90012

Agilent ESA Spectrum Analyser

Uploaded by

István Bujáki
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 9

User’s Guide

Agilent Technologies
ESA-E Series Spectrum Analyzers
Option B7K Distance to Fault Accessory Kit
Kit Part Number E4402-60009

Agilent Part Number E4402-90012


Printed in USA May 2000
Notice.
The information contained in this document is subject to change without notice.

Agilent Technologies makes no warranty of any kind with regard to this material, including but not limited
to, the implied warranties of merchantability and fitness for a particular purpose. Agilent Technologies
shall not be liable for errors contained herein or for incidental or consequential damages in connection with
the furnishing, performance, or use of this material.

© Copyright 2000 Agilent Technologies, Inc.


General Information

Introduction
Option B7K Distance to Fault Accessory Kit has been assembled to ensure that you have the
necessary ancillary equipment to set up the Cable Fault Location, Return Loss, and Loss/Gain
measurements. Because your site installation may be unique, you must provide any
additional connectors, adaptors, and cables to make the final connections to your system
equipment. This document describes and illustrates the measurement and normalization
configurations needed for each measurement. For more information on performing the
measurement or measurement normalization, you must refer to the measurement
instructions located in the ESA-E Series Spectrum Analyzers GSM Measurement Personality
Measurement Guide or the ESA-E Series Spectrum Analyzers cdmaOne Measurement
Personality Measurement Guide.

Option B7K Accessory Kit Contents


The Option B7K Accessory Kit contains the devices listed below.

Item Description Specifications Quantity Part Number

1 RF Bridge 300 kHz to 6 GHz 1 86205A


Type N
50 ohm

2 Power Divider DC to 18 GHz 1 11636A


Type N
50 ohm

3 Coaxial Termination DC to 18 GHz 1 909A Option 012


Type N(m)
50 ohm

4 Coaxial Short DC to 18 GHz 1 11512A


Type N(m)

5 Coaxial Cable 2 Foot 2 8121-0101


Type N-N
50 ohm

6 Coaxial Attenuator DC to 18 GHz 2 0955-0826


Type N(m)
50 ohm

User’s Guide E4402-90012 3


Cable Fault Location Measurement Setup

Purpose
To make the Cable Fault Location measurements using the Option B7K Accessory Kit, set up
the equipment as illustrated below.

Measurement Normalization Setup


Connect the tracking generator output, power divider, coaxial short (or open), 6 dB attenuator
(optional), and the spectrum analyzer RF input as shown in Figure 1-1. For more information
on performing the measurement normalization, refer to the Cable Fault Location
measurement in the ESA-E Series Spectrum Analyzers GSM Measurement Personality
Measurement Guide.

Figure 1-1 Normalizing the Measurement

4 User’s Guide E4402-90012


Measurement Setup
Connect the tracking generator output, power divider, cable under test, 6 dB attenuator
(optional), and the spectrum analyzer RF input as shown in Figure 1-2. For more information
on performing the measurement, refer to the Cable Fault Location measurement in the ESA-
E Series Spectrum Analyzers GSM Measurement Personality Measurement Guide.

Figure 1-2 Measurement Setup

User’s Guide E4402-90012 5


Return Loss Measurement Setup

Purpose
To make the Return Loss Location measurements using the Option B7K Accessory Kit, set up
the equipment as illustrated below.

Measurement Normalization Setup


Connect the tracking generator output, RF bridge, coaxial short (or open), 6 dB attenuator
(optional), and the spectrum analyzer RF input as shown in Figure 1-3. For more information
on performing the measurement normalization, refer to the Return Loss measurement in the
ESA-E Series Spectrum Analyzers GSM Measurement Personality Measurement Guide or
ESA-E Series Spectrum Analyzers cdmaOne Measurement Personality Measurement Guide.

Figure 1-3 Normalizing the Measurement

6 User’s Guide E4402-90012


Measurement Setup
Connect the tracking generator output, RF bridge, device under test, 50 ohm load (if the
device is a two-port device), 6 dB attenuator (optional), and the spectrum analyzer RF input
as shown in Figure 1-4. For more information on performing the measurement, refer to the
Return Loss measurement in the ESA-E Series Spectrum Analyzers GSM Measurement
Personality Measurement Guide or ESA-E Series Spectrum Analyzers cdmaOne Measurement
Personality Measurement Guide.

Figure 1-4 Measurement Setup

User’s Guide E4402-90012 7


Loss/Gain Measurement Setup

Purpose
To make the Loss/Gain measurements using the Option B7K Accessory Kit, set up the
equipment as illustrated below.

Measurement Normalization Setup


Connect the tracking generator output, 6 dB attenuator (optional), and the spectrum analyzer
RF input as shown in Figure 1-5. For more information on performing the measurement
normalization, refer to the Loss/Gain measurement in the ESA-E Series Spectrum Analyzers
GSM Measurement Personality Measurement Guide or ESA-E Series Spectrum Analyzers
cdmaOne Measurement Personality Measurement Guide.

Figure 1-5 Normalizing the Measurement

8 User’s Guide E4402-90012


Measurement Setup
Connect the tracking generator output, device under test, 6 dB attenuator (optional), and the
spectrum analyzer RF input as shown in Figure 1-6. For more information on performing the
measurement, refer to the Loss/Gain measurement in the ESA-E Series Spectrum Analyzers
GSM Measurement Personality Measurement Guide or ESA-E Series Spectrum Analyzers
cdmaOne Measurement Personality Measurement Guide.

Figure 1-6 Measurement Setup

User’s Guide E4402-90012 9

You might also like