[Federal Register: December 3, 2003 (Volume 68, Number 232)]

[Rules and Regulations]

[Page 67588-67590]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr03de03-2]
–––––––––––––––––––––––––––––––––––

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. 2003-CE-03-AD; Amendment 39-13376; AD 2003-24-07]

RIN 2120-AA64

Airworthiness Directives; The New Piper Aircraft, Inc. Models PA-31, PA-31-300, PA-31-325,
PA-31-350, PA-31P, PA-31T, PA-31T1, PA-31T2, PA-31T3, and PA-31P-350 Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule.

–––––––––––––––––––––––––––––––––––

SUMMARY: This amendment adopts a new airworthiness directive (AD) that applies to all The
New Piper Aircraft, Inc. (Piper) Models PA-31, PA-31-300, PA-31-325, PA-31-350, PA-31P, PA-
31T, PA-31T1, PA-31T2, PA-31T3, and PA-31P-350 airplanes. This AD requires you to install an
inspection hole (or use for inspection the tooling hole in the rudder bottom rib), conduct a detailed
visual inspection of the rudder torque tube and associated ribs for corrosion, and, if corrosion is
found, replace or repair the rib/rudder torque tube assembly. This AD is the result of reports of rudder
tube corrosion. The actions specified by this AD are intended to detect and correct corrosion in the
rudder torque tube assembly and rudder rib, which could result in failure of the rudder torque tube.
This failure could lead to loss of rudder control.

DATES: This AD becomes effective on February 9, 2004.

As of February 9, 2004, the Director of the Federal Register approved the incorporation by
reference of certain publications listed in the regulation.

ADDRESSES: You may get the service information referenced in this AD from The New Piper
Aircraft, Inc., Customer Services, 2926 Piper Drive, Vero Beach, Florida 32960; telephone: (772)
567-4361; facsimile: (772) 978-6584.
You may view this information at the Federal Aviation Administration (FAA), Central Region,
Office of the Regional Counsel, Attention: Rules Docket No. 2003-CE-03-AD, 901 Locust, Room
506, Kansas City, Missouri 64106; or at the Office of the Federal Register, 800 North Capitol Street,
NW., suite 700, Washington, DC.

FOR FURTHER INFORMATION CONTACT: William O. Herderich, Aerospace Engineer,

FAA, Atlanta Aircraft Certification Office, One Crown Center, 1895 Phoenix Boulevard, Suite 450,
Atlanta, Georgia 30349; telephone: (770) 703-6082; facsimile: (770) 703-6097.

1
SUPPLEMENTARY INFORMATION:

Discussion

What events have caused this AD? The FAA has received several reports of rudder tube and rib
corrosion on Piper PA-31 Series airplanes. The area surrounding the rudder torque tube assembly and
rudder rib does not have a means or access to inspect in this area and neither means nor exits for
water to drain out.
What is the potential impact if FAA took no action? Corrosion in the rudder torque tube assembly
and rudder rib could result in failure of the rudder torque tube. This failure could lead to loss of
rudder control.
Has FAA taken any action to this point? We issued a proposal to amend part 39 of the Federal
Aviation Regulations (14 CFR part 39) to include an AD that would apply to all Piper Models PA-31,
PA-31-300, PA-31-325, PA-31-350, PA-31P, PA-31T, PA-31T1, PA-31T2, PA-31T3, and PA-31P-
350 airplanes. This proposal was published in the Federal Register as a notice of proposed
rulemaking (NPRM) on June 3, 2003 (68 FR 33030). The NPRM proposed to require you to install
an inspection hole, conduct a detailed visual inspection of the rudder torque tube and associated ribs
for corrosion, and, if corrosion is found, replace the rib/rudder torque tube assembly.

Comments

Was the public invited to comment? We provided the public the opportunity to participate in the
development of this AD. The following presents the comments received on the proposal and FAA's
response to each comment:

Comment Issue No. 1: Extend the Compliance Time

What is the commenter's concern? A commenter recommends extending the compliance time
from 100 hours time-in-service (TIS) to 150 hours TIS. The commenter states that the extension is
necessary due to a reported lack of parts and the difficulty in scheduling involved with AD
compliance.
What is FAA's response to the concern? The FAA agrees that 150 hours TIS would be a more
realistic compliance time.
We are changing the final rule AD action accordingly.

Comment Issue No. 2: Allow Option to Repair Parts

What is the commenter's concern? The commenter recommends the following: if you find ''light
corrosion'' or ''corrosion that could significantly weaken the rib/rudder torque tube assembly that is
less than 50 percent of the thickness over an area less than two square inches' then you may clean up,
repair, and coat the corroded area to prevent further damage and continue the part in service.
What is FAA's response to the concern? The FAA is currently unaware of any approved repair
design for the rib/rudder torque tube assembly. However, FAA has no objection to operation of
aircraft with parts that have been repaired or reworked per an FAA-approved repair design.
Therefore, we are changing the final rule AD action to provide the option of repairing with an
FAA-approved design.

Comment Issue No. 3: Special Flight Permits Are Not Addressed in the NPRM

What is the commenter's concern? The commenter states that since special flight permits are not
addressed in the NPRM, the current 14 CFR part 39 applies and that there is no restriction against
issuing a special flight permit.

2
 What is FAA's response to the concern? On July 10, 2002, the FAA published a new version of
14 CFR part 39 (67 FR 47997, July 22, 2002), which governs the FAA's AD system. This regulation
now includes material that relates to special flight permits. This material previously was included in
each individual AD. Since this material is included in 14 CFR part 39, we did not include it in this
AD action.
We are not making any changes to the final rule AD action.

Comment Issue No. 4: Allow an Alternate Method of Inspection

What is the commenter's concern? The commenter suggests an alternative to installing an

inspection hole in the rudder skin for the rudder torque tube assembly. This alternative method of
inspection is to use the tooling hole in the rudder bottom rib since this is convenient and does not
contribute to corrosion. Further, you could enlarge the tooling hole to ease use of inspection tools.
What is FAA's response to the concern? The FAA agrees that the proposed alternative use of the
tooling hole (with optional enlargement) in the rudder bottom rib is an acceptable substitute to
installing an access hole.
We are changing the final rule AD action accordingly.

Comment Issue No. 5: Allow Application of Corrosion Inhibitor

What is the commenter's concern? The commenter recommends allowing application of rust
inhibitor compound.
What is FAA's response to the concern? The application of rust inhibitor compound to the
contact surfaces is identified in Piper Service Bulletin No. 1105A, dated September 22, 2003. As a
minor correction, we are also noting to protect bare metal per Section 8, FAA Advisory Circular
(AC) 43.13-1B.
We are incorporating the referenced correction in the final rule AD action.

Conclusion

What is FAA's final determination on this issue? We have carefully reviewed the available data
and determined that air safety and the public interest require adopting the AD as proposed except for
the changes discussed above and minor editorial corrections. We have determined that these changes
and minor corrections:

–Are consistent with the intent that was proposed in the NPRM for correcting the unsafe condition;
and
–Do not add any additional burden upon the public than was already proposed in the NPRM.

Changes to 14 CFR Part 39–Effect on the AD

How does the revision to 14 CFR part 39 affect this AD? On July 10, 2002, the FAA published a
new version of 14 CFR part 39 (67 FR 47997, July 22, 2002), which governs the FAA's AD system.
This regulation now includes material that relates to altered products, special flight permits, and
alternative methods of compliance. This material previously was included in each individual AD.
Since this material is included in 14 CFR part 39, we will not include it in future AD actions.

Costs of Compliance

How many airplanes does this AD impact? We estimate that this AD affects 2,269 airplanes in
the U.S. registry.
What is the cost impact of this AD on owners/operators of the affected airplanes?

3
 We estimate the following costs to accomplish the installation of inspection and drain holes and
inspection of torque tube and associated ribs for corrosion:

Labor cost Parts cost Total cost per Total cost on U.S.
airplane operators
3 workhours x $60 per hour = $180. $10 $190 2,269 x $190 = $431,110

We estimate the following costs to accomplish any necessary corrosion repairs/replacements of

the rib/torque tube assembly that would be required based on the results of this proposed inspection.
We have no way of determining the number of airplanes that may need this repair/replacement:

Labor cost Parts cost Total cost per airplane

16 workhours x $60 per hour = $960 $800 $1,760

Regulatory Findings

Will this AD impact various entities? We have determined that this AD will not have federalism
implications under Executive Order 13132. This AD will not have a substantial direct effect on the
States, on the relationship between the National Government and the States, or on the distribution of
power and responsibilities among the various levels of Government.
Will this AD involve a significant rule or regulatory action? For the reasons discussed above, I
certify that this AD:
1. Is not a ''significant regulatory action'' under Executive Order 12866;
2. Is not a ''significant rule'' under the DOT Regulatory Policies and Procedures (44 FR 11034,
February 26, 1979); and
3. Will not have a significant economic impact, positive or negative, on a substantial number of
small entities under the criteria of the Regulatory Flexibility Act.
We prepared a summary of the costs to comply with this AD and placed it in the AD Docket.
You may get a copy of this summary by sending a request to us at the address listed under
ADDRESSES. Include ''2003-CE-03-AD'' in your request.

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.

Adoption of the Amendment

Accordingly, under the authority delegated to me by the Administrator, the Federal Aviation
Administration amends part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39–AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

§ 39.13 [Amended]

2. FAA amends § 39.13 by adding a new AD to read as follows:

4
AIRWORTHINESS DIRECTIVE

Aircraft Certification Service U.S. Department

Washington, DC of Transportation
Federal Aviation
Administration
We post ADs on the internet at "www.faa.gov"
The following Airworthiness Directive issued by the Federal Aviation Administration in accordance with the provisions of Title 14 of the Code of Federal Regulations (14 CFR) part 39,
applies to an aircraft model of which our records indicate you may be the registered owner. Airworthiness Directives affect aviation safety and are regulations which require immediate
attention. You are cautioned that no person may operate an aircraft to which an Airworthiness Directive applies, except in accordance with the requirements of the Airworthiness
Directive (reference 14 CFR part 39, subpart 39.3).

2003-24-07 The New Piper Aircraft, Inc.: Amendment 39-13376; Docket No. 2003-CE-03-AD.

When Does This AD Become Effective?

(a) This AD becomes effective on February 9, 2004.

What Other ADs Are Affected by This Action?

(b) None.

What Airplanes Are Affected by This AD?

(c) This AD affects the following airplane models and serial numbers that are certificated in any
category:

Model Serial numbers

PA–31, PA–31–300, PA–31-325 31–2 through 31–8312019
PA–31–350 31–5001 through 31–8553002
PA–31P 31P–1 through 31P–7730012
PA–31P–350 31P–8414001 through 31P–8414050
PA–31T 31T–7400001 through 31T–8120104
PA–31T1 31T–7804001 through 31T–1104017
PA–31T2 31T–8166001 through 31T–1166008
PA–31T3 31T–8275001 through 31T–5575001

What Is the Unsafe Condition Presented in This AD?

(d) This AD is the result of reports of rudder tube corrosion. The actions specified by this AD are
intended to detect and correct corrosion in the rudder torque tube assembly and rudder rib, which
could result in failure of the rudder torque tube. This failure could lead to loss of rudder control.

What Must I Do to Address This Problem?

(e) To address this problem, you must accomplish the following:

5
 Actions Compliance Procedures
(1) Install an inspection hole in the Within the next 150 Install an inspection hole per The
rudder skin for the rudder torque tube hours time-in-service New Piper Aircraft, Inc. Service
assembly; OR instead of installing an (TIS) after February Bulletin No. 1105A, dated
inspection hole, use the tooling hole in 9, 2004 (the effective September 22, 2003. Protect bare
the rudder bottom rib. You may date of this AD), metal per Section 8, FAA Advisory
enlarge the diameter of the tooling unless already Circular (AC) 43.13–1B.
hole no more than 0.25 inches to accomplished.
facilitate inspection and corrosion
treatment.
(2) Visually inspect the rudder torque Before further flight Follow The New Piper Aircraft,
tube and associated ribs for corrosion.
after the installation Inc. Service Bulletin No. 1105A,
required in paragraph September 22, 2003.
(e)(1) of this AD and
thereafter at intervals
not to exceed 12
calendar months.
(3) If you find corrosion damage: Before further flight Follow The New Piper Aircraft,
(i) Replace the rib/rudder torque after any inspection Inc. Service Bulletin No. 1105A,
assembly; OR required in paragraph dated September 22, 2003. Repairs
(ii) Repair the damaged torque tube (e)(2) of this AD must address items in paragraph (f)
using an FAA-approved repair design. where corrosion of this AD and may be approved
damage is found. per FAA Order 8300.10 (Volume
2, Chapter 1), Airworthiness
Inspector’s Handbook.

(f) All repairs must address the following:

(1) Detect hidden corrosion damage:
(i) In the faying surface between the rudder ribs and torque tube assembly attachments.
(ii) Inside the bore of the torque tube.
(2) Establish procedures for removing corrosion or for corrosion prevention of repaired parts.
Advisory Circular (AC) 43.13-1B Acceptable Methods, Techniques, and Practices-Aircraft
Inspection and Repair, and AC 43-4A, Corrosion Control for Aircraft, provide resources for
establishment of these procedures.
(3) For repairs involving material removal without reinforcement: Define a clear, accurate, and
complete description of negligible damage limits. Note that acceptable amounts of material removal
may be location-dependent. Higher-stressed areas will be less tolerant of material removal.
(4) For all repairs involving reinforcement: A clear, accurate, and complete description of the
repair design must be established per 14 CFR part 21.31.
(5) Verify that all repairs follow Subpart C–Strength Requirements and Subpart D–Design and
Construction of Civil Aviation Regulations (CAR) 3, dated May 15, 1956 (the original certification
basis for the Piper PA-31 Series as shown in type certificate data sheets A8EA and A20SO).

May I Request an Alternative Method of Compliance?

(g) You may request a different method of compliance or a different compliance time for this AD
by following the procedures in 14 CFR 39.13. Send your request to the Manager, Atlanta Aircraft
Certification Office (ACO), FAA. For information on any already approved alternative methods of

6
compliance, contact William O. Herderich, Aerospace Engineer, FAA, Atlanta ACO, One Crown
Center, 1895 Phoenix Boulevard, Suite 450, Atlanta, Georgia 30349; telephone: (770) 703-6082;
facsimile: (770) 703-6097.

Does This AD Incorporate Any Material by Reference?

(h) You must do the actions required by this AD following the instructions in The New Piper
Aircraft, Inc. Service Bulletin No. 1105A, dated September 22, 2003. The Director of the Federal
Register approved the incorporation by reference of this service bulletin per 5 U.S.C. 552(a) and 1
CFR part 51. You may get a copy from The New Piper Aircraft, Inc., Customer Services, 2926 Piper
Drive, Vero Beach, Florida 32960; telephone: (772) 567-4361; facsimile: (772) 978-6584. You may
review copies at FAA, Central Region, Office of the Regional Counsel, 901 Locust, Room 506,
Kansas City, Missouri 64106; or at the Office of the Federal Register, 800 North Capitol Street, NW.,
suite 700, Washington, DC.

Issued in Kansas City, Missouri, on November 24, 2003.

James E. Jackson,
Acting Manager, Small Airplane Directorate, Aircraft Certification Service.
[FR Doc. 03-29871 Filed 12-2-03; 8:45 am]
BILLING CODE 4910-13-P