New FluiDyne Valves

Directional Valves D03 & D05

Needle Valves

Stak Valves: PO Check, Reducing,

Flow Control, Check, Relief

w w w . F l u i D y n e F P. c o m
New FluiDyne Valves

4 Way 3 and 2 position solenoid operated

directional valves for D03 and D05 valves with
a variety of voltage and spool configurations.

• D03 & D05 • 18 month warranty

• Flow rate 14 GPM for D03 • Cost effective replacement to Rexroth, Bosch,
Vickers, and Parker with superior performance
• Flow rate 22 GPM for D05
• Large inventory allows same day shipment in
• 350 bar / 5000 PSI
most cases.
• Endurance tested to 10 million cycles

WFDG4V3 Model Code Table (D03) FluiDyne - VICKERS DESIGN COIL

For coils Mfg after 2008
WFDG4V3(S) 2 C M FTWL B 560 D03 SIZE
RATED Hz WORKING IN-RUSH HOLDING POWER
DO3 Sub plate VOLTAGE VOLTAGE CURRENT CURRENT WATTS
mounted 4-way
directional valve Design Code DC12 — 10.8~13.2 — 2.5A 30
DC24 — 21.6~26.4 — 1.25A 30
Spool Config.
See Chart Cell Identification AC110V 50/60 Hz 99~121 1.7A 0.48A 30
B- 110/120 Volts AC
Spool Arrangement D- 220/240 Volts AC AC220V 50/60 Hz 198~242 0.85A 0.25A 30
A-Spring offset single
G- 12 Volt DC
solenoid
H- 24 Volt DC
D05 SIZE
B-Spring centered single
solenoid RATED Hz WORKING IN-RUSH HOLDING POWER
C-Spring centered double
FTWL- Flying lead, wired VOLTAGE VOLTAGE CURRENT CURRENT WATTS
solenoid
terminal black, wire
housing, and light kit. DC12 — 10.8~13.2 — 3A 36
Electrical Options available
(e.g. Light Kit) U-Din connector DC24 — 21.6~26.4 — 1.5A 36
(ISO 43650)
AC110V 50/60 Hz 99~121 4.49A 0.87A 40
AC220V 50/60 Hz 198~242 2.9A 0.55A 40
WFDG4S4 Model Code Table (D05)

WFDG4S4 LW 01 2 C U B 60 Spool Chart

Spool Center A B C (Rexroth
Position Spool)
DO5 Sub plate Design Code
mounted 4-way (H)
directional valve
Cell Identification
B- 110/120 Volts AC (E)
D- 220/240 Volts AC
Light Kit & G- 12 Volt DC
Wire Housing H- 24 Volt DC
(J)

Omit- for Din U-Din connecters (M)

connectors (ISO 43650)
Omit=Flying leads
ISO-4401-50-4-A (G)
NFPA D05 Spool Arrangement
A-Spring offset single solenoid Note: Spool Transition Shown
Spool Options B-Spring centered single solenoid
See spool chart C-Spring centered double solenoid

• 1-800-842-5377 • 586-296-7200 • www.FluiDyneFP.com • Page 1

New FluiDyne Valves

WFDG4V3(S) – Hydraulic Directional Valve D03

Subplate / Manifold Mounted
Solenoid Operated
P, A, B Pressure Rated 5000 psi (350 bar)
T Pressure Rate at 1450 psi (100 bar)
Flows to 14 GPM (54 l/m)
Wiring box is 1/2” NPT thread
DIN female connection plugs included

120 VAC Coils 60 HZ – D03 (B) Coil

Spool Valves Description

2C WF DG4V3S2CMFTWLB560 Wiring box, spring centered, two solenoids, light kit,

120 VAC 50/60 HZ

2C WF DG4V3S2CMUB560 Din connectors, spring centered, two solenoids,

120 VAC, 50/60 HZ

6C WF DG4V3S6CMFTWLB560 Wiring box, spring centered, two solenoids, light kit,

120 VAC, 50/60 HZ

6C WF DG4V3S6CMUB560 Din connectors, spring centered, two solenoids,

120 VAC, 50/60 HZ

8C WF DG4V3S8CMFTWLB560 Wiring box, spring centered, two solenoids, light kit,

120 VAC, 50/60 HZ

8C WF DG4V3S8CMUB560 Din connectors, spring centered, two solenoids

120 VAC, 50/60 HZ

2A WF DG4V3S2AMFTWLB560 Spring Offset, “A” port, Wiring Box, single

Solenoid light kit, 120 VAC 50/60 HZ

2A WF DG4V3S2AMUB560 Spring Offset, “A” port, Din Connector, single,

solenoid, 120 VAC 50/60 HZ

0C WF DG4V3S0CMFTWLB560 Wiring box, spring centered, two solenoids, light

kit, 120 VAC, 50/60 HZ

7C WF DG4V3S7CMFTWLB560 Wiring box, spring centered, two solenoids, light

kit, 120 VAC, 50/60 HZ

Note: See page 7 for spool function chart.

D03 valves have (4) # 10-24”x (45mm) 1 3/4” bolts included.

• 1-800-842-5377 • 586-296-7200 • www.FluiDyneFP.com • Page 2

New FluiDyne Valves

WFDG4V3(S) – Hydraulic Directional Valve D03

12 VDC Coils – D03 (G) Coil

Spool Valves Description
2C WF DG4V3S2CMFTWLG560 Wiring box, spring centered, two solenoids,
12 VDC
2C WF DG4V3S2CMUG560 Din connectors, spring centered, two solenoids
12 VDC
6C WF DG4V3S6CMFTWLG560 Wiring box, spring centered, two solenoids,
12 VDC
6C WF DG4V3S6CMUG560 Din connectors, spring centered, two solenoids
12 VDC
2A WF DG4V3S2AMFTWLG560 Spring Offset, “A” port, Wiring Box, single
solenoid, 12 VDC
2A WF DG4V3S2AMU560 Spring Offset, “A” port, Din Connector, single
solenoid, 12 VDC

24 VDC Coils – D03 (H) Coil

Spool Valves Description
2C WF DG4V3S2CMFTWLH560 Wiring box, spring centered, two solenoids,
light kit, 24 VDC
2C WF DG4V3S2CMUH560 Din connectors, spring centered, two solenoids
24 VDC
6C WF DG4V3S6CMFTWLH560 Wiring box, spring centered, two solenoids,
light Kit, 24 VDC
6C WF DG4V3S6CMUH560 Din connectors, spring centered, two solenoids
24 VDC
2A WF DG4V3S2AMFTWLH560 Spring Offset, “A” port, Wiring Box, single
solenoid, light kit, 24 VDC
2A WF DG4V3S2AMUH560 Spring Offset, “A” port, Din Connector, single
Solenoid, 24 VDC
7C WF DG4V3S7CMFTWLH560 Din connectors, spring centered, two solenoids,
24 VDC

Note: See page 7 for spool function chart.

D03 valves have (4) # 10-24”x (45mm) 1 3/4” bolts included.

• 1-800-842-5377 • 586-296-7200 • www.FluiDyneFP.com • Page 3

New FluiDyne Valves

WFDG4S4 – Hydraulic Directional D05

Subplate / Manifold Mounted
Solenoid Operated
P, A, B Pressure Rated 4500 psi (310 bar)
T Pressure Rate at 1000 psi (69 bar)
Flows to 21.5 GPM (80 l/m)
Wiring box is 1/2” NPT thread
DIN female connection plugs included

120 VAC Coils 60 HZ – D05 (B) Coil

Spool Valves Description

2A WF DG4S4LW012AB60 Wiring box, spring offset to “A” Single solenoid,

Light kit, 120 VAC, 50/60 HZ

2A WF DG4S4012AUB60 Din connectors, spring offset to “A” Single

solenoid, 120 VAC, 50/60 HZ

2C WF DG4S4LW012CB60 Wiring box, spring centered, two solenoids,

Light kit, 120 VAC, 50/60 HZ

2C WF DG4S4012CUB60 Din connectors, spring centered, two solenoids,

120 VAC, 50/60 HZ

6C WF DG4S4LW016CB60 Wiring box, spring centered, two solenoids,

Light kit, 120 VAC, 50/60 HZ

6C WF DG4S4016CUB60 Din connectors, spring centered, two solenoids,

120 VAC, 50/60 HZ

8C WF DG4S4LW018CB60 Wiring box, spring centered, two solenoids,

Light kit, 120 VAC, 50/60 HZ

8C WF DG4S4018CUB60 Din connectors, spring centered, two solenoids,

120 VAC, 50/60 HZ

7C WF DG4S4LW017CB60 Wiring box, spring centered, two solenoids,

Light kit, 120 VAC, 50/60 HZ

Note: See page 7 for spool function chart.

D05 valves have (4) # 10-24”x (45mm) 1 3/4” bolts included.
Kit Part Number WFBK702504

• 1-800-842-5377 • 586-296-7200 • www.FluiDyneFP.com • Page 4

New FluiDyne Valves

WFDG4S4 – Hydraulic Directional D05

12 VDC Coils – D05 (G) Coil
Spool Valves Description

2C WF DG4S4LW012CG60 Wiring box, spring centered, two solenoids,

Light kit, 12 VDC

2A WF DG4S4LW012AG60 Wiring box, spring offset to “A” Single solenoid,

Light kit, 12 VDC
2C WF DG4S4012CUG60 Din connectors, spring centered, two solenoids,
12 VDC
2A WF DG4S4012AUG60 Din connectors, spring offset to “A” Single solenoid,
Light kit, 12 VDC
6C WF DG4S4LW016CG60 Wiring box, spring centered, two solenoids,
Light kit, 12 VDC
6C WF DG4S4016CUG60 Din connectors, spring centered, two solenoids,
12 VDC
7C WF DG4S4017CUG60 Din connectors, spring centered, two solenoids,
12 VDC

24 VDC Coils – D05 (H) Coil

Spool Valves Description

2C WF DG4S4LW012CH60 Wiring box, spring centered, two solenoids,

Light kit, 24 VDC

2A WF DG4S4LW012AH60 Wiring box, spring offset to “A” Single solenoid,

Light kit, 24 VDC
2C WF DG4S4012CUH60 Din connectors, spring centered, two solenoids,
24 VDC
2A WF DG4S4012AUH60 Din connectors, spring offset to “A” Single solenoid,
Light kit, 24 VDC
6C WF DG4S4LW016CH60 Wiring box, spring centered, two solenoids,
Light kit, 24 VDC
6C WF DG4S4016CUH60 Din connectors, spring centered, two solenoids,
24 VDC
7C WF DG4S4017CUH60 Din connectors, spring centered, two solenoids,
24 VDC
Note: See page 7 for spool function chart.
D05 valves have (4) # 10-24”x (45mm) 1 3/4” bolts included.
Kit Part Number WFBK702504

• 1-800-842-5377 • 586-296-7200 • www.FluiDyneFP.com • Page 5

 New FluiDyne Valves

D03 & D05 Subplates, Manifolds, and Accessories

Ordering Information

Material Valve Pattern Product Type Port Location Port Threads

-6 SAE
A Aluminum - 6061-T6
3000† psi 20.7 MPa SP Subplate 6S* ISO 11926;
S Side Ported SAE 1926

D03 ISO 4401-03-02

B Bottom Ported -8 SAE
NFPA T3.5.1-D03
8S ISO 11926;
SAE 1926
D05 ISO 4401-05-04
NFPA T3.5.1-D05 *Available on D03 only

SUBPLATES, MANIFOLDS, AND ACCESSORIES

WF P/N WF Model Code Note
Subplates
WF860195 AD03SPS6S D03, Side ported SAE -6
WF860291 AD03SPS8S D03, Side ported SAE -8
WF860335 AD03SPB8S D03, Bottom ported SAE -8
WF860292 AD05SPS8S D05, Side ported SAE -8
WF860336 AD05SPB8S D05, Bottom ported SAE -8
Manifold Parallel Multi-Stations
WF860295 AD03P022S/C D03 2-STATION SAE PORTS,
D03 w/relief cavity (C-10-2)**
Dimension A B C D E F G H WF860296 AD03P032S/C D03 3-STATION SAE PORTS,
AD03SPS6* 1.00 2.50 1.31 1.25 0.50 0.25 2.25 0.88 w/relief cavity (C-10-2)**
(25.4) (63.5) (33.3) (31.8) (12.7) (6.4) (57.2) (22.4)
AD03SPS8* 1.50 3.50 1.81 1.76 0.75 0.25 3.25 1.38 WF860297 AD05P023S/C D05 2-STATION SAE PORTS,
(38.1) (88.9) (46.0) (45.2) (19.1) (6.4) (82.6) (34.9) w/relief cavity (C-10-2)**
WF860298 AD05P033S/C D05 3-STATION SAE PORTS,
w/relief cavity (C-10-2)**
Blank Cover Plate
WF860301 AD03CPP D03 BLANKING PLATE
WF860302 AD05CPP D05 BLANKING PLATE
Manifold Accessories
V889566 RV510S020/ RELIEF VALVE 100-2,000
PSI RANGE (fits C-10-2 cavity)
V02-352137 RV510S035/30 RELIEF VALVE SET @3,000 psi
(fits C-10-2 cavity) 250-3,500
PSI RANGE
V565814 BLANK PLUG BLANK CAVITY PLUG C-10-2
C-10-2 CAVITY
D05 Note: All manifolds are parallel circuit design
** Relief valve must be ordered separately

• 1-800-842-5377 • 586-296-7200 • www.FluiDyneFP.com • Page 6

New FluiDyne Valves

D03 & D05 Subplates, Manifolds, and Accessories

Hydraulic Directional Valves
Solenoids Standards:
Functional symbols related to
solenoid identity “A” and / or “B”
according to NFPA standards, i.e.
energizing solenoid “A” gives flow
P to B, solenoid “B” gives flow P to A.

D03 Bolt Kits:

Valve Length Kit #
* Valve Only 1.75” (44.45 mm) WFBK702500
Valve + 1 module 3.5” (88.9 mm) WFBK702501
Valve + 2 modules 5” (127 mm) WFBK702502
Valve + 3 modules 6.5” (165.10 mm) WFBK702503

D05 Bolt Kits:

Valve Length Kit #
* Valve Only 1.5” (38.1 mm) WFBK702504
Valve + 50 mm 3.75” (95.25 mm) WFBK702505
Valve + 55 mm 3.75” (95.25 mm) WFBK702506
Valve + 60 mm 3.75” (95.25 mm) WFBK702506
Valve + 50 mm 6” (152.4 mm) WFBK702508
Valve + 50 mm + 55 mm 6” (152.4 mm) WFBK702509
Valve + 55 mm + 60 mm 6” (152.4 mm) WFBK702510
Valve + 55 mm + 55 mm 6” (152.4 mm) WFBK702510
*Included with WFD Valve WFBK Bolt Kits have (4) bolts in each kit

• 1-800-842-5377 • 586-296-7200 • www.FluiDyneFP.com • Page 7

New FluiDyne Valves

D03 Stack Valves

PO Check Valves: D03

14.5 psi check cracking pressure
Sandwich Thickness 40 mm

Valves: Description:

WF DGMPC-3ABK BAK-41 Dual Cross over checks

WF DGMPC-3ABK-41 Check in "A", pilot from "B"

WF DGMPC-3BAK-41 Check in "B", pilot from "A"

Reducing Valves: D03

Pressure reduced in "P", piloted from "P"
Hand knob Adjustment
Sandwich Thickness 40 mm

Valves: Description:

WF DGMX2 3 PP B-41 Adjustment range 50 to 1000 psi, Reduced in P

WF DGMX2 3 PP C-41 Adjustment range 145 to 2000 psi, Reduced in P

WF DGMX2 3 PP F-41 Adjustment range 290 to 3625 psi, Reduced in P

WF DGMX2 3 PA B-41 Adjustment range 50 to 1000 psi, Reduced in A

WF DGMX2 3 PA C-41 Adjustment range 145 to 2000 psi, Reduced in A

WF DGMX2 3 PA F-41 Adjustment range 290 to 3625 psi, Reduced in A

WF DGMX2 3 PB B-41 Adjustment range 50 to 1000 psi, Reduced in B

WF DGMX2 3 PB C-41 Adjustment range 290 to 3625 psi, Reduced in B

WF DGMX2 3 PB F-41 Adjustment range 290 to 3625 psi, Reduced in B

Note: See page 7 for spool function chart.

D03 valves have (4) # 10-24”x (45mm) 1 3/4” bolts included.

• 1-800-842-5377 • 586-296-7200 • www.FluiDyneFP.com • Page 8

New FluiDyne Valves

D03 Stack Valves

Flow Control Valves: D03

Hand Knob Adjustment
Sandwich Thickness 40 mm

Valves: Description:

WF DGMFN 3 Y A2W-41 Flow Control Meter-out A port

WF DGFN 3 X A2W-41 Flow Control Meter-in A port

WF DGMFN 3 Y B2W-41 Flow Control Meter-out B port

WF DGMFN 3 X B2W-41 Flow Control Meter-in B port

WF DGMFN 3 Y A2W B2W-41 Flow Control Meter-out A & B ports

WF DMFN 3 X A2W B2W-41 Flow Control Meter-in A & B ports

Check Valves: D03

Sandwich Thickness 40 mm

Valves: Description:

WF DGMDC 3 T XL-41 Free flow away from actuator, Check in T port, 5 psi

WF DGMDC 3 A XL-41 Free flow away from actuator, Check in A port, 5 psi

WF DGMDC 3 B XL-41 Free flow away from actuator, Check in B port, 5 psi

WF DGMDC 3 P YL-41 Free flow towards actuator, Check in P port, 5 psi

WF DGMDC 3 T XR-41 Free flow away from actuator, Check in T port, 50 psi

WF DGMDC 3 A XR-41 Free flow away from actuator, Check in A port, 50 psi

WF DGMDC 3 B XR-41 Free flow away from actuator, Check in B port, 50 psi

WF DGMDC 3 P YR-41 Free flow towards actuator, Check in P port, 50 psi

Note: See page 7 for spool function chart.

D03 valves have (4) # 10-24”x (45mm) 1 3/4” bolts included.

• 1-800-842-5377 • 586-296-7200 • www.FluiDyneFP.com • Page 9

New FluiDyne Valves

D03 Stack Valves

Relief Valves: D03

Hand Knob Adjustment
Sandwich Thickness 40 mm

Valves: Description:

WF DGMC3 PT B-41 Pressure in "P" relieved to "T", 44 psi thru 1450 psi (3-100 Bar)

WF DGMC3 AT B-41 Pressure in "A" relieved to "T", 44 psi thru 1450 psi (3-100 Bar)

WF DGMC3 BT B-41 Pressure in "B" relived to "T", 44 psi thru 1450 psi (3-100 Bar)

WF DGMC2 3 AT B BT B-41 Dual Relief Pressure in "A" relieved to "T" Pressure in "B"
port relieved to "T", 47 psi thru 1450 psi (3-100 Bar)

WF DGMC3 PT C-41 Pressure in "P" relieved to "T", 500 psi thru 2000 psi

WF DGMC3 AT C-41 Pressure in "A" relieved to "T", 500 psi thru 2000 psi

WF DGMC3 BT C-41 Pressure in "B" relived to "T", 500 psi thru 2000 psi

WF DGMC2 3 AT C BT C-41 Dual Relief Pressure in "A" relieved to "T" Pressure in "B"
port relieved to "T", 500 psi thru 2000 psi

WF DGMC2 3 AT F BT F-41 Dual Relief Pressure in "A" relieved to "T" Pressure in "B"
port relieved to "T", 800 psi thru 3600 psi

WF DGMC3 PT F-41 Pressure in "P" relieved to "T", 800 psi thru 3600 psi

WF DGMC3 AT F-41 Pressure in "A" relieved to "T", 800 psi thru 3600 psi

WF DGMC3 BT F-41 Pressure in "B" relived to "T", 800 psi thru 3600 psi

Note: See page 7 for spool function chart.

D03 valves have (4) # 10-24”x (45mm) 1 3/4” bolts included.

• 1-800-842-5377 • 586-296-7200 • www.FluiDyneFP.com • Page 10

New FluiDyne Valves

D05 Stack Valves

PO Check Valves: D05

14.5 psi check cracking pressure
Sandwich Thickness 50 mm

Valves: Description:

WF DGMPC-5ABK BAK-41 Dual Cross over checks

WF DGMPC-5ABK-41 Check in "A", pilot from "B"

WF DGMPC-5BAK-41 Check in "B", pilot from "A"

Reducing Valves: D05

Pressure reduced in "P", piloted from "P" and reduced in “A” and “B”
Hand knob Adjustment
Sandwich Thickness 60 mm

Valves: Description:

WF DGMX2 5 PP B-41 Adjustment range 50 to 1000 psi, Reduced in P

WF DGMX2 5 PP C-41 Adjustment range 145 to 2000 psi, Reduced in P

WF DGMX2 5 PP F-41 Adjustment range 290 to 3625 psi, Reduced in P

WF DGMX2 5 PA B-41 Adjustment range 50 to 1000 psi, Reduced in A

WF DGMX2 5 PA C-41 Adjustment range 145 to 2000 psi, Reduced in A

WF DGMX2 5 PA F-41 Adjustment range 290 to 3625 psi, Reduced in A

WF DGMX2 5 PB B-41 Adjustment range 50 to 1000 psi, Reduced in B

WF DGMX2 5 PB C-41 Adjustment range 145 to 2000 psi, Reduced in B

WF DGMX2 5 PB F-41 Adjustment range 290 to 3625 psi, Reduced in B

Note: See page 7 for spool function chart.

D05 valves have (4) # 10-24”x (45mm) 1 3/4” bolts included.

• 1-800-842-5377 • 586-296-7200 • www.FluiDyneFP.com • Page 11

New FluiDyne Valves

D05 Stack Valves

Flow Control Valves: D05

Hand Knob Adjustment
Sandwich Thickness 55 mm

Valves: Description:

WF DGMFN 5 Y A2W-41 Flow Control Meter-out A port

WF DGFN 5 X A2W-41 Flow Control Meter-in A Port

WF DGMFN 5 Y B2W-41 Flow Control Meter-out B port

WF DGMFN 5 X B2W-41 Flow Control Meter-in B port

WF DGMFN 5 Y A2W B2W-41 Flow Control Meter-out A & B ports

WF DGMFN 5 X A2W B2W-41 Flow Control Meter-in A & B ports

Check Valves: D05

Sandwich Thickness 55 mm

Valves: Description:

WF DGMDC 5 X TL-41 Free flow away from actuator, Check in T port, 5 psi

WF DGMDC 5 X AL-41 Free flow away from actuator, Check in A port, 5 psi

WF DGMDC 5 X BL-41 Free flow away from actuator, Check in B port, 5 psi

WF DGMDC 5 Y PL-41 Free flow towards actuator, Check in P port, 5 psi

WF DGMDC 5 X TR-41 Free flow away from actuator, Check in T port, 60 psi

WF DGMDC 5 X AR-41 Free flow away from actuator, Check in A port, 60 psi

WF DGMDC 5 X BR-41 Free flow away from actuator, Check in B port, 60 psi

WF DGMDC 5 Y PR-41 Free flow towards actuator, Check in P port, 60 psi

Note: See page 7 for spool function chart.

D05 valves have (4) # 10-24”x (45mm) 1 3/4” bolts included.

• 1-800-842-5377 • 586-296-7200 • www.FluiDyneFP.com • Page 12

New FluiDyne Valves

D05 Stack Valves

Relief Valves: D05

Hand Knob Adjustment
Sandwich Thickness 55 mm

Valves: Description:

WF DGMC5 PT B-41 Pressure in "P" relieved to "T", 48 psi thru 1450 psi

WF DGMC5 AT B-41 Pressure in "A" relieved to "T", 48 psi thru 1450 psi

WF DGMC5 BT B-41 Pressure in "B" relived to "T", 48 psi thru 1450 psi

WF DGMC2 5 AT B BT B-41 Dual Relief Pressure in "A" relieved to "T" Pressure in "B"
port relieved to "T", 48 psi thru 1450 psi

WF DGMC5 PT C-41 Pressure in "P" relieved to "T", 100 psi thru 2000 psi

WF DGMC5 AT C-41 Pressure in "A" relieved to "T", 100 psi thru 2000 psi

WF DGMC5 BT C-41 Pressure in "B" relived to "T", 100 psi thru 2000 psi

WF DGMC2 5 AT C BT C-41 Dual Relief Pressure in "A" relieved to "T" Pressure in "B"
port relieved to "T", 100 psi thru 2000 psi

WF DGMC5 PT F-41 Pressure in "P" relieved to "T", 125 psi thru 3600 psi

WF DGMC5 AT F-41 Pressure in "A" relieved to "T", 125 psi thru 3600 psi

WF DGMC5 BT F-41 Pressure in "B" relived to "T", 125 psi thru 3600 psi

WF DGMC2 5 AT F BT F-41 Dual Relief Pressure in "A" relieved to "T" Pressure in "B"
port relieved to "T", 125 psi thru 3600 psi

Note: See page 7 for spool function chart.

D05 valves have (4) # 10-24”x (45mm) 1 3/4” bolts included.

• 1-800-842-5377 • 586-296-7200 • www.FluiDyneFP.com • Page 13

New FluiDyne Valves

In-Line Valves
Rated to 5000 PSI (315 Bar)

In-Line Needle Valves

Controls Flow in both Directions

(
(
WFD Part Number Description Parker Part Number Max.
(For reference only) Flow
WF860144 1/4 inch NPT Female-Female N400SFV 5 GPM
WF860145 3/8 inch NPT Female-Female N600SFV 8 GPM
WF860146 1/2 inch NPT Female-Female N800SFV 15 GPM
WF860147 3/4 inch NPT Female-Female N1200SFV 25 GPM
WF860148 1 inch NPT Female-Female N1600SFV 40 GPM
WF860149 1 1/4 inch NPT Female-Female N2000SFV 70 GPM
WF860150 # 4 SAE Female –Female N420SFV 5 GPM
WF860151 # 6 SAE Female –Female N620SFV 8 GPM
WF860152 # 8 SAE Female –Female N820SFV 15 GPM
WF860153 # 10 SAE Female –Female N1020SFV 15 GPM
WF860154 # 12 SAE Female –Female N1220SFV 25 GPM
WF860155 # 16 SAE Female –Female N1620SFV 40 GPM
WF860156 # 20 SAE Female –Female N2020SFV 70 GPM
WF860157 # 24 SAE Female –Female N/A

In-Line Flow Control Valves

Controls Flow in one Direction

(
(

WFD Part Number Description Parker Part Number Max.

(For reference only) Flow
WF860158 1/4 inch NPT Female-Female F400SFV 5 GPM
WF860159 3/8 inch NPT Female-Female F600SFV 8 GPM
WF860160 1/2 inch NPT Female-Female F800SFV 15 GPM
WF860161 3/4 inch NPT Female-Female F1200SFV 25 GPM
WF860162 1 inch NPT Female-Female F1600SFV 40 GPM
WF860163 1 1/4 inch NPT Female-Female F2000SFV 70 GPM
WF860164 # 4 SAE Female –Female F420SFV 5 GPM
WF860165 # 6 SAE Female –Female F620SFV 8 GPM
WF860166 # 8 SAE Female –Female F820SFV 15 GPM
WF860167 # 10 SAE Female –Female F1020SFV 15 GPM
WF860168 # 12 SAE Female –Female F1220SFV 25 GPM
WF860169 # 16 SAE Female –Female F1620SFV 40 GPM
WF860170 # 20 SAE Female –Female F2020SFV 70 GPM
WF860171 # 24 SAE Female –Female F2420SFV 100 GPM

• 1-800-842-5377 • 586-296-7200 • www.FluiDyneFP.com • Page 14

New FluiDyne Valves

4 Way 3 and 2 position lever operated

directional valves for D05 and D03 valves
with a variety of spool configurations.

WFDG17V3 Model Code Table (D03)

• D03 & D05
WFDG17V3 2 C 60
• Flow rate 14 GPM for D03
D03 Sub plate
mounted 4-way • Flow rate 26 GPM for D05
directional valve Design Code
• 4500 PSI
Spool Config.
See Chart • Endurance tested to 10 million cycles
Spool Arrangement • 18 month warranty
A- Spring offset single lever operated
C- Spring centered lever operated • Cost effective replacement to Rexroth, Bosch,
N- Detented lever operated, no spring Vickers, and Parker with superior performance
• Large inventory allows same day shipment in
most cases.

WFDG17S4 Model Code Table (D05) DG17* Valve Configuration

WFDG17S4 01 2 C 60 OC ON

D05 Sub plate

mounted 4-way 2C
directional valve Design Code 2N

Spool Options 6C 6N
See valve
configuration
chart Spool Arrangement OA(L)
A- Spring offset single lever operated
2A(L)
C- Spring centered lever operated
N- Detented lever operated, no spring (L) 6A(L)

• 1-800-842-5377 • 586-296-7200 • www.FluiDyneFP.com • Page 15

12/11