Scribd
Upload
29 views

CEMS

The document describes an online continuous emission monitoring system that can monitor multiple parameters such as particulate matter, HCl, SPM, SO2, CO, O2, CO2, NOx, and SOx from emission stacks. The system uses specific sensors and analytical measurements to determine gas and particulate concentrations and emission rates with data updates every 1 to 30 minutes. It has features like online remote calibration, alarms, data storage of up to a year, and fault diagnosis. The system can operate between -45°C to 45°C and uses 5-32V DC power.

Uploaded by

Zulfequar Ali Ahmad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
29 views

CEMS

The document describes an online continuous emission monitoring system that can monitor multiple parameters such as particulate matter, HCl, SPM, SO2, CO, O2, CO2, NOx, and SOx from emission stacks. The system uses specific sensors and analytical measurements to determine gas and particulate concentrations and emission rates with data updates every 1 to 30 minutes. It has features like online remote calibration, alarms, data storage of up to a year, and fault diagnosis. The system can operate between -45°C to 45°C and uses 5-32V DC power.

Uploaded by

Zulfequar Ali Ahmad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Online Continuous Emission Monitoring System

SPM HCL

CO2
O2
CO

SOX
NOX

Introduction
In recent years Online Emission Monitoring Technology has received attention and interest in context of providing
accurate and continuous information on particulate matter/ gaseous emission from stacks. There are already com-
mercially available systems for monitoring parameters such as PM, HCL, SPM, SO2, CO, O2, CO2, NOx, SOX, etc.
The Continuous Emission Monitoring (CEMS) System comprises of the total equipment necessary to determine the
concentration of gaseous emission and/or particulate matter concentration and/or emission rate using analytical
measurement.

Alarms For Automatic


Low & High Operation
Specific Sensors Low Cost Of
Maintenance
Features -
• Data Uploading Time 1 Min To 30 Min.
• Online Remote Calibration (Optional).
• Online Calibration Of Gases.
• Online System Failure Alarms (Optional).
• Build In Cloud Connector For Online Data Transfer.
• Sampling Time Variable From 1 Sec To 999 Sec.
• Data storage Time Up to 90 Days (Optional Up to 1 Year).
• Online Fault Diagnostic Feature.
• Password protection For Users And Pollution Board.

Technical Specification

Sensors Technology Measurement Range Operating Temp Power supply

SOX NDIR/EC 0-1000 ppm 0-45°C 5 – 32V DC

NOX NDIR/EC 0-1000 ppm 0 -45°C 5-32V DCv

CO2 NDIR/EC 0-2550000 ppm 10-45°C 5-32V DCv


CO NDIR/EC 0-10000 ppm 10-45°C 5-32V DCv
O2 NDIR/EC 0-2550000 ppm 0 -45°C 5-32V DCv
SPM Optical 0 – 1000 ppm 10 -40°C 5-32V DCv

HCL NDIR/EC 0-1000 ppm 0-45°C 5-32V DCv

Outdoor Suction unit SO2 NU NU

Gas Filter
Solenoid Moisture
Pump
Walve Trap

Display
To Servers

Main Panel

BOD COD
Unit
Probe
Shott-off value
EMF
Effluent

TDS SAR TSS pH

Stack Transmitters

Effluent Treatment Plant

You might also like