Scribd
Upload
294 views

Lab Assignment 1 (TempRTD) 1

This document provides instructions for a lab assignment on calibrating a resistance temperature device (RTD) sensor to measure temperature. Students will use an RTD sensor module connected to a temperature control unit to take resistance and temperature readings as heat is applied. They are to record readings over time in a table, then plot a graph of resistance versus temperature and write a report on the results. The document explains how to set up the circuit and sensor, calibrate the RTD for 20°C, take readings as heat is applied, and how to convert the voltage readings into temperature and resistance values to chart and analyze.

Uploaded by

MuTaYaM_EmArAtI
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
294 views

Lab Assignment 1 (TempRTD) 1

This document provides instructions for a lab assignment on calibrating a resistance temperature device (RTD) sensor to measure temperature. Students will use an RTD sensor module connected to a temperature control unit to take resistance and temperature readings as heat is applied. They are to record readings over time in a table, then plot a graph of resistance versus temperature and write a report on the results. The document explains how to set up the circuit and sensor, calibrate the RTD for 20°C, take readings as heat is applied, and how to convert the voltage readings into temperature and resistance values to chart and analyze.

Uploaded by

MuTaYaM_EmArAtI
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 6

EELX N302

Instrumentation & Control 1

Year 2011

EELX N302

Lab Assignment 1 RTD Temperature Sensor (Calibration)

Purpose : To investigate the suitability of a resistance-temperature-device (RTD) as a


sensor for measuring temperature.

Introduction
In this lab you will use the temperature sensor module (fig. 1) on the Digiac 1750 Transducer and Instrumentation Trainer module. The trainer is described in Appendix A at the end of this document. The active transducers are mounted within a clear plastic enclosure, which contains a heater. The heated enclosure is provided to raise the temperature of the sensor transducer to allow measurements to be taken during the experiment.

Figure 1

70009365.doc

Page 1 of 6

EELX N302

Instrumentation & Control 1

Year 2011

PLATINUM RTD TRANSDUCER


Platinum RTD (Resistance Temperature Detector) consists of a thin film of platinum deposited on a ceramic substrate having gold contact plates at each end that makes contact with the film as shown below:

The resistance of the film increases as the temperature increases. Thus it has a positive temperature coefficient p.t.c. Rt = Ro + 0.385 t Where, Rt = resistance at temperature t C Ro = resistance at 0 C (=100) The increase in resistance is linear, the relationship between resistance changes and temperature rise being 0.385 /C Set the slider of the 10 K carbon resistor to mid-way and connect the circuit as shown below with the digital voltmeter set to its 200 mV or 2 V DC range.

Switch ON the power supply and adjust the slider control of the 10 K resistor so that the voltage drop across the platinum RTD is 108 mV. This calibrates the platinum RTD for an assumed ambient temperature of 20 C since the resistance of the RTD at 20C will be 108 . Note that the voltage reading across the RTD

70009365.doc

Page 2 of 6

EELX N302

Instrumentation & Control 1

Year 2011

in mV is the same as the RTD resistance in , since the current flowing must be 0.108 = 1mA. 108 Connect the +12V supply to the heater element input and note the voltage across the RTD with the voltmeter set to its 200mV or 2V range (representing the RTD resistance) and the output voltage from the IC temperature sensor with the voltmeter set to its 20V range (representing the temperature of the RTD) every one minute Convert the two voltage readings to RTD temperature (K) and RTD resistance measured () and record the values in the table below Convert the RTD temperature into C (K 273) and record in the table below. Calculate the RTD resistance (= 100 + 0.385 x C) and record in the table below. Time (minutes)
RTD Temperature RTD Resistance

0 K C

10

Plot the graph of RTD resistance (measured) against temperature C .

70009365.doc

Page 3 of 6

EELX N302

Instrumentation & Control 1

Year 2011

Report
You should complete a report for this lab and submit it by ____________

Assessment Descriptor
Report Layout Table /Results Graph Summary/Conclusion 1 1 1 1

Grading
2 3 4 5 2 3 4 5 2 3 4 5 2 3 4 5

Weight
*2 *3 *3 *1

Score

/10 /15 /15 /5 Total /45 For the grading, 1 represents the lowest score and 4 the highest score. No attempt will receive no score in that element.

70009365.doc

Page 4 of 6

EELX N302

Instrumentation & Control 1

Year 2011

Appendix A
The layout diagram of the DIGIAC 1750 Transducer and Instrumentation trainer unit

70009365.doc

Page 5 of 6

EELX N302

Instrumentation & Control 1

Year 2011

PART A (IC TEMPERATURE SENSOR)


The IC temperature sensor is an LM 335 providing an output of 10 mV/K

The IC temperature sensor gives a voltage output of 10mV/ oK. That is 0.01 x oK. In other words, V = 0.01oK, or
o

K = 100 x V.

Therefore, oC = 100V 273, since oC = oK 273.

70009365.doc

Page 6 of 6

You might also like