REPAIR MANUAL & PARTS LIST FOR FUJICA ST-705 By Eva HEHOTO FILM SO, HD: wzabu 2-Chome, Minato-ku, Tokyo 106. JapiCONTENTS EUJICA ST705 CONTENTS _ Please Note: Pages 6, 28, 96 & 102 are blank and have been omitted. Page |, TROUBLESHOOTING ... 5 1, METER NEEDLE DOES NOT DEFLECT 2. METER NEEDLE DEFLECTS CONTINUOUSLY TO THE MAXIMUM 3. METER DOES NOT OPERATE ACCORDINGLY WITH SELECTSD APERTURE OR SHUTTER SPEED OR CHANGED BRIGHTNESS OF OBJECT OVER OR UNDER EXPOSURE DUPLICATE EXPOSURE FILM IS SCARRED OR SCRATCHED... LIGHT LEAKING .. FILM ADVANCE LEVER DOES NOT MOVE . MIRROR DOES NOT COME DOWN 10. INCORRECT SHUTTER SPEED 11, FLASH DOES NOT SYNCHRONIZE 1 MI. DISASSEMBLY 1. TOP COVER ASSEMBLY (1-1) .. AMPLIFIER ASSEMBLY (2-34) SHUTTER RESISTOR ASSEMBLY (2-1) 10 COUNTER ASSEMBLY (2-48)... : 2 PENTA PRISM ASSEMBLY (3-1) AND PHOTOCELL ASSEMBLY (2-43)... 14 6. PRISM (34) .. 4 FOCUSING SCREEN ASSEMBLY (3-12) 4 BOTTOM COVER (1-70) zs si i 16 9. LENS MOUNT ASSEMBLY (1-46) 10 16 10. BACK COVER ASSEMBLY (1-76) 16 11. SELP-TIMER ASSEMBLY (3-101) .. 18 12, SYNCHRO-CONTACT ASSEMBLY (3-21) AND BRAKE ASSEMBLY (8:35) eovneennnnnninnetenn 18 19. REMOVING FOCAL PLANE SHUTTER ASSEMBLY .. 20 14, DISASSEMBLING FOCAL PLANE SHUTTER ASSEMBLY : 22 15. MAIN BODY ASSEMBLY 1076.5 ACONTENTS: FUJICA ST705 WL, REPAIR & ADJUSTMENT 10. uu. 12, 13, 14, 15. 16. i. 18. IV. INSPECTION . V. PARTS LIST .. MAIN BODY ASSEMBLY FOCAL PLANE SHUTTER ASSEMBLY ... ADJUSTMENT OF 45° ALIGNMENT OF THE MIRROR STOPPED-DOWN/FULL-APERTURE LIGHT CHANGEOVER SWITCH ASSEMBLY .. ADJUSTMENT OF CONTACT POSITION FOR F-VALUE APERTURE RESISTOR ASSEMBLY (4-215) INSTALLATION OF LENS MOUNT ASSEMBLY (1-46) AND ADJUSTMENT OF FLANGEBACK LENS MOUNT ASSEMBLY (1-46) VIEWFINDER, INSTALLATION OF EXPOSURE COUNTER AND ADJUSTMENT OF ADVANCEMENT INSTALLATION OF SHUTTER RESISTOR ASSEMBLY (2-1) ADJUSTMENT OF MAIN SWITCH FOR EXPOSURE METER CIRCUIT ADJUSTMENT OF FILM ADVANCEMENT LOCK AND LOCK RELEASE MECHANISM INSTALLATION OF AMPLIFIER AND WIRING ADJUSTMENT OF EXPOSURE METER .. CHECKING EXPOSURE METER INSTALLING TOP COVER ASSEMBLY (1-1) .. INSTALLING FILM ADVANCE LEVER ASSEMBLY (1-98), FILM REWIND KNOB ASSEMBLY (1-33) AND REWIND BUTTON (1-71) LIGHT SHIELDING PARTS .. aa Page 29 30 26 62 64 66 68 70 4 78 8 80 80 82 84 86 90 92 94 7 103 1976,5TROUBLESHOOTING FUJICAST705 I. TROUBLESHOOTING 1976, 5 oe‘TROUBLESHOOTING FUJICA ST705 TROUBLESHOOTING 1. METER NEEDLE DOES NOT DEFLECT Mercury battery (3.0 + 0.2V) a No se ~~ Replace. y P86 Battery chamber (corrosion; continuity) No. Tes “Stx_Repatroramplaces ’ p.86 Power switch ————> no Yes ~~ Repair. Y p.80 Meter (wire breaking) ae No. 7 S_ Replaces ’ p.86 Amplifier See p.86 2. METER NEEDLE DEFLECTS CONTINUOUSLY TO THE MAXIMUM Amplifier (output voltage) See p. 86 3, METER DOES NOT OPERATE ACCORDINGLY WITH SELECTED APERTURE OR SHUTTER SPEED OR CHANGED BRIGHTNESS OF OBJECT Silicon photocell mg Yes Na Replace, ’ p.88 Shutter resistor Shutter jester * ~ma_Repair or replace. 88 F-value selector =—=e_oseoe——~. ‘No Yes ~m_ Replace. 1 p88 Amplifier Now Replace. p.86 -2- 1976, 5‘TROUBLESHOOTING FUJICA ST705 4, OVER OR UNDER EXPOSURE Mercury battery (3.0+ 0.2V) es ase No, Yes Replace. ’ P. 86 Power switch (contact; short-circuiting) No Yes ee Repair. p. 80 Amplifier No Yes ~m__Replace. p.86 Meter 7 No Yes 7 Replace. 1 Ss Shutter esistor —no Yes ~a_ Repair or replace. ’ p.88 value selector Shc Rapalnaneel ae) =, p. 88 ~~__Replace. p85 Exposurt meter ~~ ‘No ~~ Adiust 5, DUPLICATE EXPOSURE Sprocket No ~a_Remair p. 82 Film take-up ratchet No ~~ Repair. p30 1976,5 -3-TROUBLESHOOTING FUJICA ST705, 6. FILM IS SCARRED OR SCRATCHED Coated side of film (projection in camera body) ~ No Yes ~~ Repair Base side of film (pressure plate; roller) No Yes ~~ Repair or replace. Cassette ——~1, —~ja_ Repair or replace. LIGHT LEAKING Film and cassette (moquette and other ight shielding parts) 1 No, Yes ’ aa See p. 94 Actual photographing test 8, FILM ADVANCE LEVER DOES NOT MOVE Lock/release mechanism TN Yes ~~ Repair. p.80 Shutter release No. ~~ _Repair. p48 ss 1976, 5TROUBLESHOOTING FUJICA ST708 9. MIRROR DOES NOT COME DOWN Mirror setting system (set/stop lever (4-149). en i, Yes ~_ Repair, v p.36 Shutter blind starting system No —~a__Repair. 10. INCORRECT SHUTTER SPEED Shutter blind traveling velocity (12 msec.) ie te Yes —~a_Repair. + PAs Shutter peed no Adjust. . 50, p. 62 ‘11, FLASH DOES NOT SYNCHRONIZE X-contact {time lag: 0.6 to 1.5 msec.) No ~x_ Repair p88 1976, 5 -5-DISASSEMnLy FUJICA ST705 IL. DISASSEMBLY 1976.5 -7-DISASSEMBLY FUJICA ST705 Il. DISASSEMBLY 1, TOP COVER ASSEMBLY (1-1) a. Film rewind knob assembly (1-23) Hold the rewind shaft (2-82), and turn the fim rewind knob assembly (1-33) counter- clockwise to remove it. b, Film advance lever assembly (1-98) ‘Turn the serew (1-96) counterclockwise with a piece of rubber or other proper tool to remove it, and remove the film advance lever assembly (1-98). c. Remove the cap (1-5). d. ‘Turn the ring (1-12) counterclockwise with a piece of rubber or other proper tool, and remove (Recommend repair tool (J306) be used.) e, Remove two screws (1-32). £, Pullup the top cover assembly (1-1) slowly and carefully. NOTE: 1. Pay attention for the lead wire connected to the accessory shoe. 2, Be careful not to lose connector plate assembly (1-29). 8- 1976.5DISASSEMBLY EUJICA ST705 2. AMPLIFIER ASSEMBLY (234) a. Unsolder and disconnect six lead wires (6-1, 6-2, 6-3, 6-5, printed circuit board of the amplifier assembly (2-34), 8, 6-10, 6-23 and 6-24) from the b. Unsolder and isconnect the lead wire (6-9) from the contact spring (2-25). cc. Unsolder and disconnect two lead wires (6-11 and 6-12) from the transit plate assembly (2-28) a. Remove the serew (2-33). fe. With the lead wires connected to the transit plate assembly, remove the transit plate assembly (2-23), 3. SHUTTER RESISTOR ASSEMBLY (2-1) a, Disconnect terminals of lead wires (6-5, 6-11, 6-12 and 6-23). b. Remove the serew (2-20), and remove the index plate (2-21), c. Remove three screws (2-22). d, Remove the shutter resistor assembly (2-1) upward. fe. Be careful not to lose the coupling (3-40). 1976.5DISASSEMBLY FUJICA ST705, 4. COUNTER ASSEMBLY (2-48) a. Turn two columns (2-79) counterclockwise, and remove them. b. Remove the counter assembly (2-45) upward. @ 1976.5DISASSEMBLY FUJICA 7705 ase are) Lg “4 eee 1978,5 t=DISASSEMBLY FUJIGA ST705 5. PENTA PRISM ASSEMBLY (3-1) AND PHOTOCELL ASSEMBLY (2-43) Remove screws (2-47 and 2-75), and remove the photocell assembly (2-43). b. Remove two screws (3-11). 6 PRISM (3-6) When cleaning inside of the viewfinder, remove the prism (3-6) alone as described below. a. Remove two screws (3-4). b, Hold the rough surface of the prism, and remove it. . Carefully handle the frame (3-7). It is made of film, 7. FOCUSING SCREEN ASSEMBLY (3-12) Remove three screws (3-17), and remove the focusing screen assembly (3-12). NOTE: Be careful not to lose leaf springs (3-18 and 3-19). -14- 1976,EDISASSEMBLY FUJICA ST705 8 BOTTOM COVER (1-70) Remove two screws (1-72), and remove the bottom cover (1-70). NOTE: Be careful not lose the rewind button (1-71), 9. LENS MOUNT ASSEMBLY (1-46) a, Use solvent such as ketone to solve Pliobond, and peel off leathers (1-74 and 1-78), Set the self-timer in a half way. Remove four screws (1-108). d. Remove the lens mount assembly (1-46) forward and carefully so as not to lose the shaft (1-67). 10. BACK COVER ASSEMBLY (1-76) Remove three screws (1-109), and remove the back cover assembly (1-76). =1Bs 1976, 5Fig. 5DISASSEMBLY FUJICA ST705 11. SELF-TIMER ASSEMBLY (3-101) a. _ Use solvent such as ketone to solve Pliobond used in the joint between shutter release shaft assembly (3-92) and release shaft (3-102), and separate them by turning the shutter release shaft assembly and release shaft counterclockwise. b. Remove two screws (3-100), and remove the self-timer assembly. 12. SYNCHRO-CONTACT ASSEMBLY (3-21) AND BRAKE ASSEMBLY (3-35) a, Disconnect two lead wires (3-25). b. Remove screws (3-28 and 3-29). ¢. Remove the synchro-contact assembly carefully so as not to lose the collar (3-30). 4. Remove the screw (3-31). fe. Remove the spring (3-38) carefully so that it is not deformed. Recommend the screw (5-18) to which the spring has been hooked be removed. £, Remove the brake assembly carefully. Helicolube/Molykote mixed grease has been applied. ~48~ 1976,5