Scribd
Upload
308 views1 page

Eddy Current Testing Exam Questions Assignment2

The document is an assignment of 30 multiple choice questions related to eddy current testing from Trinity Institute of NDT Technology. It covers topics like calculating impedance from resistance and inductive reactance, factors that influence eddy current density and flow, effects of material properties and probe design on detection, suitable frequencies for different materials, and methods for improving signal detection and analysis.

Uploaded by

Narotam Kumar Gupteshwar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
308 views1 page

Eddy Current Testing Exam Questions Assignment2

The document is an assignment of 30 multiple choice questions related to eddy current testing from Trinity Institute of NDT Technology. It covers topics like calculating impedance from resistance and inductive reactance, factors that influence eddy current density and flow, effects of material properties and probe design on detection, suitable frequencies for different materials, and methods for improving signal detection and analysis.

Uploaded by

Narotam Kumar Gupteshwar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

TRINITY INSTITUTE OF NDT TECHNOLOGY

#491, 14TH Cross, 4th Phase, Peenya Industrial Area, Bangalore 560 058. INDIA.
Phone: +91-80-41205245, 9141339994 E: [email protected] W: www.trinityndt.com

EDDY CURRENT TESTING COURSE – ASSIGNMENT - I I


1. If resistance of coil is 6 ohms and inductive reactance is 8 ohms calculate the impedance.
2. Eddy Current Density at one standard depth of penetration is __________% of the surface.
3. Alloy composition will have influence on conductivity of the material. (T/F)
4. When length of conductor increases, resistance ____(increases, decreases, remain same)
5. Eddy Currents can characterize grain size change after heat treatment. (T/F)
6. Aluminium is a ___________(dia, para, ferro) magnetic material.
7. Permeability value of Air is _____________
8. Lift-off is considered a noise source and it is undesirable in defect detection. (T/F)
9. The distance where the edge effect is present is from approximately ____ to ____ times the
diameter of the inspection coil in the case of encircling probes
10. Typical inspection frequencies in eddy current testing are in the range of ____Hz–___ MHz
11. ___ (high, low, medium) frequency is commonly used in the inspection of ferromagnetic materials
12. To detect smaller discontinuities low frequency is used to maximize eddy current flow (T/F).
13. Multi-frequency testing is also applied to cancel out undesired signals in order to improve the
signal-to noise ratio. (T/F)
14. Pancake-type coil probes are not suitable for detecting ________ flaws as currents flow parallel
to the surface
15. _____________(Absolute, Differential) probes consist of a single coil that generates eddy
currents and senses changes from the eddy current field.
16. ______________(Absolute, Differential) coils do not detect gradual dimensional or composition
variations of the test piece.
17. Differential encircling probes only detect discontinuities when a long crack that is parallel to the
major axis. (T/F)
18. Eddy current techniques also take advantage of ___________variation to measure the coating
thickness of non-conductive materials.
19. Formula for calculating fill factor for an internal coil is ________________
20. For Good Coupling, Fill Factor should always be ____________and above.
21. Reduction in coil size _______(increases, decreases) edge effect.
22. Lift off is applied for _____________(surface, encircling, bobbin) coils.
23. For ferromagnetic materials the problem of permeability variation is eliminated by ________
24. Frequency range generally suitable for Titanium is _________Hz to _______Hz
25. For eddy current testing of steels, the penetration is high due to permeability.(T/F)
26. _______(Absolute, Differential) coils have the advantage of being able to detect very small
discontinuities.
27. Coils can be and are arranged so that one coil induces the field and a second coil picks up the
signal is called _____________coils
28. The transmission method needs a maximum thickness of the test material of 5 ~ 8 times the
standard penetration depth to be able to receive the signal in the pick-up coil. (T/F)
29. In Shielded probes the former(core) is made of ___________material
30. ______________probe is suitable for finding laminar type flaws in plates.
Answers Ref: TINT/ET/B/0423/00
EDDY CURRENT TESTING QUESTIONS ASSIGNMENT 2 Find more at www.trinityndt.com

You might also like