METER

ultrasonic level transmitter

technical documentation EN Rev. of 24/09/2021

 METER - contents

CONTENTS
1-WARRANTY page 3

2-PRODUCT page 4

3-PERFORMANCE SPECIFICATIONS page 5

4-DIMENSIONS page 6

5-INSTALLATION page 7

6-ELECTRICAL CONNECTIONS page 11

7-LOCAL OPERATOR INTERFACE (LOI)-VL601 page 13

8-QUICK SETUP page 15

9-ADVANCED SETUP page 23

10-FACTORY TEST AND QUALITY CERTIFICATE page 40

Pa g e 2 o f 4 0 www.sgm-lektra.com
 METER - warranty

1-WARRANTY

Products supplied by SGM LEKTRA are guaranteed for a period of 12 (twelve) months from delivery date according to the
conditions specified in our sale conditions document.
SGM LEKTRA can choose to repair or replace the Product.
If the Product is repaired it will maintain the original term of guarantee, whereas if the Product is replaced it will have 12
(twelve) months of guarantee.
The warranty will be null if the Client modifies, repair or uses the Products for other purposes than the normal conditions
foreseen by instructions or Contract.
In no circumstances shall SGM LEKTRA be liable for direct, indirect or consequential or other loss or damage whether
caused by negligence on the part of the company or its employees or otherwise howsoever arising out of defective goods

www.sgm-lektra.eu Pa ge 3 o f 4 0
 METER - features

2- PRODUCT

1
2

1. Anticondensation filter
2. M20 skintop
3. VL601 (opt.)
4. Sensor

2.1 IDENTIFICATION
Each meter has an adhesive identifi cation plate on which are the meter main data. The following picture describes the
information and data on the identifi cation plate.

1 Mod. METER1F4D
2 P.S. 24Vdc 20÷30Vdc
3 S.N. MU0081604506

1. Product code 2. Power supply 3. Serial number

Pa g e 4 o f 4 0 www.sgm-lektra.com
 METER - features

3-FEATURES
Housing/sensor material
PC or Al / PP wetted part (only PVDF for ATEX certified vers.)
Mechanical installation
2” GAS M (PP flange DN80 opt.)
Protection degree
IP67/IP68 (Sensor)
Electrical connection
Internal push connectors
Working temperature
-30 ÷ +70°C; +80°C non-continuous
Pressure
from 0,5 to 1,5 bar (absolute)
Power supply
12Vdc / 20÷30Vdc (2-wires versions) - 24Vdc (4-wires versions)
Power consumption
0,6W (2-wires) - 1,5W (4-wires)
Analog output
4...20mA, max 750ohm (4-wires versions)
Relays output
(4-wire only) n°2 3A 230Vac (n.o.) with a resistive load
Digital communication
MUDBUS RTU for 4-wire vers. ; (opt.) HART for 2-wire vers.
Max measure range
max 0.25 ÷ 6m
max 0.40 ÷10m
In case of non perfectly reflecting surfaces, the maximum distance value will be reduced
Blind distance
0,25m (6m versions) / 0,40m (10m versions)
Temperature compensation
digital from -30 to 80°C
Accuracy
±0,2% (of the measured distance) not better than ±3mm.
Resolution
1mm.
Calibration
4 buttons or via HART / MODBUS RTU
Warm-up
5 minutes typical
LCD Display
Plug-in display/keyboard 4 buttons matrix LCD
Ex-proof
ATEX II 1/2G Ex ia II C T6 Tamb -20 ÷ +60°C

www.sgm-lektra.eu Pa ge 5 o f 4 0
 METER - dimensions

4-DIMENSIONS
4.1 MECHANICAL DIMENSIONS
PP HOUSING PP HOUSING + EXTENSION

Ø95 127,5 127,5

223

66

2" G Ø55,5
239,5

ALUMINIUM HOUSING
Ø95 127,5

Ø55,5
232,5

66

2" G Ø55,5

Pa g e 6 o f 4 0 www.sgm-lektra.com
 METER - installation

5-INSTALLATION
5.1 MOUNTING PRECAUTIONS
5.1.1 Mounting position
- With cambered roof, Do not install the sensor in the tank center (b). Leave a 300mm (d) minimum distance
between the sensor and the tank smooth wall.
- Use a protective cover to protect the sensor from weather and direct sunlight (c).
- Do not install the sensor near the load zone (a).
- Make sure that in the sensor emission beam (lobe “α”) there are no obstacles (f,s) that can be
intercepted as level.
- Make sure that there is not foam presence on the product surface to be measured.

Lobo
“α“

METER 6mt 5°

METER
5°
10mt

5.1.2 Blind distance

During installation is important to remember that in the sensor vicinity there is a blind zone (or BLIND DISTANCE) of 0.25m
(for 6m max METER range) or 0.4m (for 10m max METER range) where the sensor can not measure.

0.25mt (6mt)
0.40mt (10mt) Blind Distance

www.sgm-lektra.eu Pa ge 7 o f 4 0
 METER - installation
5.1.3 Installation in nozzle

Installing the METER sensor in a nozzle, make sure the sensor bottom protrudes at least 10 mm from the bottom nozzle.

≥10mm.

METER can be installed in an extension pipe to turn away the sensor from the maximum level point. The extension pipe must
be flat and without joints (welds, etc..), also, the pipe terminal part must be cut at 45° and with the borders without burr.

METER 6mt METER 10mt

D (mm) Lmax(mm) D (mm) Lmax(mm)

L

57 180 80 240

80 240 100 300

100 300

Pa g e 8 o f 4 0 www.sgm-lektra.com
 METER - installation
5.1.4 Reference pipe installation
Disturbing factors that may influence the level measurement in liquids, as for example:
- foam presence on the product surface
- internal structures presence in the tank
- presence on the liquid surface of floating bodies
can be avoided with the use of level measurement inside of pipes (by-pass pipe or calm pipe with 57mm min. diameter).
The pipe must have a length greater or equal than the empty distance, also, must have some of vent holes to allow the
pipe regular filling and emptying.
In the programming menu, to the “PRODUCT” parameter, must select the “LIQUID PIPE” option

Foam Internal structures Floating bodies

Vent hole Ø5÷10mm

www.sgm-lektra.eu Pa ge 9 o f 4 0
 METER - installation
5.1.5 Agitators presence

The level measurement is possible thanks to the Auto-Tuned statistical filter.

Should rarely need to adjust the filter setting by editing 2 METER sensor programming parameters:
- FILTER; this parameter is present in the Quick Setup menu and in the Advanced Configuration “SETUP” menu;
increasing the parameter value, decreases the sensor sensitivity to the level measurement sudden variations.
- F-WINDOW; this parameter is present in the Advanced Configuration “SERVICE” menu; decreasing the parameter
programmed value, increases the sensor immunity to false echoes.

Page 10 of 40 www.sgm-lektra.com
 METER - electrical connections

6-ELECTRICAL CONNECTIONS
6.1 WIRING
1) Separate the engine control cables or power cables from the METER connection cables
2) Open the cap by unscrewing.
3) Lead the cables into the transmitter through the glands
4) Do not use sleeves terminals, because they might interfere with the VL601 module insertion
5) Close the cap and tighten the cable glands

2 - WIRE VERSION 4 - WIRE VERSION

ALIM. 24Vdc

B
MUDBUS A
+
RL1 c

RL2 c
No

No

4÷20mA -
4÷20mA (24Vdc)
HART (opz.)

6.2 HUMIDITY INFILTRATIONS

To avoid the humidity infiltration inside the housing is recommended:
- for electrical connections, use a cable with a 6÷12mm outer diameter and fully tighten the M20 cable gland
- fully tighten the cap
- position the cable so that it forms a downward curve at the M20 output; in this way the condensation and/or rain
water will tend to drip from the curve bottom

www.sgm-lektra.eu Page 11 of 40
 METER - electrical connections
6.3 DIGITAL COMMUNICATIONS CONNECTION
6.3.1 - 4-wires METER; MODBUS RTU PC connection

1) METER4____ or METER8____ with MODBUS RTU communication protocol

2) USB/RS485 interface module, cod.694A004A
3) MODBUS RTU communication S/W, cod.010F105A, for METER transmitter
With this software is possible:
- connect, by selecting the UID address, the METER transmitters in MODBUS RTU network
- read on your PC monitor all measures in reading and METER operation data
- programming all METER configuration parameters
- storing on files, data logger function; METER measures in reading and operating states

USB/RS485

6.3.2 - 2-wires METER; HART Hand Held connection or HART PC/MODEM

1) METER-__, METER0__, METER2__, METER7__, with HART communication protocol

2) 250ohm resistance
3) HART MODEM
4) HART communication S/W, cod.010E105A (for PC HART MODEM only)
5) HART HAND-HELD

4
3

Page 12 of 40 www.sgm-lektra.com
 METER - local operator interface (LOI) - VL601

7-LOCAL OPERATOR INTERFACE (LOI) - VL601

LOI is an operator communications center for the METER. Through the LOI, the operator can access any
transmitter function for changing configuration parameter settings or other functions.

7.1 VL601 FEATURES

The VL601 program module has 4 buttons which allow to perform all operational, control and programming
instrument functions.
In the configuration menus, is possible:

1. Submenus and parameters access; press to select and press to access.

2. Parameter options choice: Press to select the option and press to store the option.

Press to exit without storing.

3. Configure the parameter values; in some parameters the configuration is done by setting a value (eg., in the
SET DISTANCE 4mA parameter is possible to change the the corresponding distance value, in mm):

press to select the digit to be modified (the digit is highlighted in inverse ), press to change the high

lighted digits number, press to save the set value and exit automatically.

Press to exit without storing.

LEFT ARROW button:

• Exit configuration
• Back to previous menu
• Echo map (from RUN mode)

UP ARROW button:
• Parameter values modification
• Parameter scroll

SCROLL button:
• Cursor movement (to the right)
• Parameter scroll

ENTER button:
• Configuration access
• Options confirmation
• Parameters values confirmation

Displayed at the bottom indicates the correct echo signal reception

!
Displayed at the top alerts that there is a generic error; press SCROLL to show the message that
indicates the present error type.
The METER returns automatically to RUN mode.

www.sgm-lektra.eu Page 13 of 40
 METER - local operator interface (LOI) - VL601

The VL601 programming module can be mounted and removed from the METER without affecting the unit operation. Unscrewing
the cap, the VL601 module can be mounted (by clockwise rotation until it clicks) or dismounted (by rotation counterclockwise)
as shown in figure.

LOCK UNLOCK

Page 14 of 40 www.sgm-lektra.com
 METER - quick setup

8-QUICK SETUP
8.1 - Quick Setup menu structure

Parameter Default Values

Set Distance 4mA 6000mm (6mt max range)

0000 mm 10000mm (10mt max range)
Set Distance 20mA 300mm (6mt max range)
0000 mm 500mm (10mt max range)
Quick Setup Set Distance 4mA Medium
>Liquids
Set Distance 20mA Liquids
Solids
Liquids Pipe
Medium
Filter Coefficient
20
Filter Coefficient 000
Blind Distance 250mm (6mt max range)
Blind Distance 0000 mm 400mm (10mt max range)
Display Distance mm
Level mm
RL1 Threshold Level % Distance mm
Output mA
RL2 Threshold Temperature °C
RL1 Threshold
0mm (Disabled RL1)
0000 mm
RL1 Threshold 0mm (Disabled RL2)
0000 mm

8.2 - QUICK SETUP MODE

4321
D
From “RUN” mode press ENTER to access the Quick Setup menu.
mm

Select the parameters by moving the cursor with SCROLL, and confirm with ENTER; ► SET DISTANCE 4mA
SET DISTANCE 20mA
press LEFT ARROW to exit.
FILTER TYPE
FILTER COEFFICENT
BLIND DISTANCE
DISPLAY
RL1 THRESHOLD
RL2 THRESHOLD

www.sgm-lektra.eu Page 15 of 40
 METER - quick setup

8.2.1 SET DISTANCE 4mA ► SET DISTANCE 4mA

SET DISTANCE 20mA
Press ENTER to display the distance value associated with 4mA output. FILTER TYPE
FILTER COEFFICENT
BLIND DISTANCE
DISPLAY
RL1 THRESHOLD
RL2 THRESHOLD

Use SCROLL and UP ARROW to modify that value; in the example the 4mA distance
is 3500mm. SET DISTANCE 4mA
Press ENTER to confirm.

3500 mm
8.2.2 SET DISTANCE 20mA SET DISTANCE 4mA
► SET DISTANCE 20mA
FILTER TYPE
Press ENTER to display the distance value associated with 20mA output.
FILTER COEFFICENT
BLIND DISTANCE
DISPLAY
RL1 THRESHOLD
RL2 THRESHOLD

Use SCROLL and UP ARROW to modify that value; in the example the 20mA dis-
SET DISTANCE 20mA
tance is 500mm.
Press ENTER to confirm.
0500 mm

METER
Reference point

20mA distance
100%
Level measurement

0%
4mA distance

Page 16 of 40 www.sgm-lektra.com
 METER - quick setup

8.2.3 MEDIUM SET DISTANCE 4mA

SET DISTANCE 20mA
Press ENTER to display the previous setting ► MEDIUM
FILTER COEFFICENT
BLIND DISTANCE
DISPLAY
RL1 THRESHOLD
RL2 THRESHOLD

Press SCROLL to select the medium type. MEDIUM

Press ENTER to confirm. ► LIQUIDS

SOLIDS

LIQUIDS PIPE

LIQUIDS SOLIDS LIQUIDS PIPE

www.sgm-lektra.eu Page 17 of 40
 METER - quick setup

8.2.4 FILTER COEFFICIENT SET DISTANCE 4mA

SET DISTANCE 20mA
Press ENTER. FILTER TYPE
Use SCROLL and UP ARROW to modify the value. Input a value from 1 to 99. ► FILTER COEFFICENT
BLIND DISTANCE
1 maximum speed, 99 maximum slowness.
DISPLAY
The function is deactivated with 0 (immediate response). RL1 THRESHOLD
Press ENTER to confirm RL2 THRESHOLD

FILTER COEFFICENT

20

Fast resp. 5÷10 Normal resp. 20 Slow resp. 40÷100

Page 18 of 40 www.sgm-lektra.com
 METER - quick setup

8.2.5 BLIND DISTANCE SET DISTANCE 4mA

SET DISTANCE 20mA
Press ENTER. FILTER TYPE
he BLIND ZONE is used to avoid undesired measures near to the transmitter. FILTER COEFFICENT
► BLIND DISTANCE
DISPLAY
RL1 THRESHOLD
RL2 THRESHOLD

Use SCROLL and UP ARROW to modify the value. Press ENTER to confirm. The
BLIND DISTANCE
minimum value is 250mm (6m max vers.) or 400mm (10m max vers.).

0250 mm

METER
reference point

BLIND ZONE

BLIND
DISTANCE

8.2.6 DISPLAY SET DISTANCE 4mA

SET DISTANCE 20mA
Press ENTER to access the settings change. FILTER TYPE
FILTER COEFFICENT
BLIND DISTANCE
► DISPLAY
RL1 THRESHOLD
RL2 THRESHOLD

With the SCROLL button is possible to select the data to display

► DISTANCE mm
Press ENTER to confirm. LEVEL mm
LEVEL %
OUTPUT mA

www.sgm-lektra.eu Page 19 of 40
 METER - quick setup

8.2.7 RL1 THRESHOLD SET DISTANCE 4mA

SET DISTANCE 20mA
Press ENTER to display the previous setting. Set the distance from the sensor FILTER TYPE
FILTER COEFFICENT
BLIND DISTANCE
DISPLAY
► RL1 THRESHOLD
Use SCROLL and UP ARROW to modify the value; in the example the RL1 max. level RL2 THRESHOLD
threshold distance is 700mm.
Press ENTER to confirm.
RL1 THRESHOLD
NB - RL1 inactive with 0000mm
0700 mm
When confirming with the ENTER button the maximum level threshold value storage, in the example 700m, the METER
activates RL1 with the following default settings for level alarm threshold:
1) MIN / MAX = MIN; maximum level alarm
2) DELAY = 0 sec.; no switching delay
3) SECURITY = YES; relay de-energized, and contact open, during the maximum level alarm
4) ENABLE / DISABLE = ENABLE; alarm threshold function enabled
5) MIN/MAX HYSTERESIS mm = 40mm
To change these relay settings is necessary to access the advanced setup menu and any subsequent changes to the RL1
threshold value not affect the relay custom settings..

RL1, MAX LEVEL ALARM METER

reference point

allarm zone
700mm.

Max level
Le
ve
l RL1 THRESHOLD
SET
HYSTERESIS

Max. Max.
Alarm Alarm
RL1 “ON”
RL1 RL1 RL1 RL1
RL1 “OFF”
RL1 RL1 RL1 RL1

Page 20 of 40 www.sgm-lektra.com
 METER - quick setup

8.2.8 RL2 THRESHOLD SET DISTANCE 4mA

SET DISTANCE 20mA
Press ENTER to display the previous setting. Set the distance from the sensor FILTER TYPE
FILTER COEFFICENT
BLIND DISTANCE
DISPLAY
RL1 THRESHOLD
Use SCROLL and UP ARROW to modify the value; in the example the RL2 min. level ► RL2 THRESHOLD
threshold distance is 3000mm.
Press ENTER to confirm.
RL2 THRESHOLD
NB - RL2 inactive with 0000mm
3000 mm
When confirming with the ENTER button the maximum level threshold value storage, in the example 3000mm the ME-
TER activates RL2 with the following default settings for level alarm threshold:
1) MIN / MAX = MAX; minimum level alarm
2) DELAY = 0 sec.; no switching delay
3) SECURITY = YES; relay de-energized, and contact open, during the maximum level alarm
4) ENABLE / DISABLE = ENABLE; alarm threshold function enabled
5) MIN/MAX HYSTERESIS mm = 40mm
To change these relay settings is necessary to access the advanced setup menu and any subsequent changes to the RL2
threshold value not affect the relay custom settings.

RL2, MIN. LEVEL ALARM METER

reference point
3000mm.

Leve
l
HYSTERESIS RL2 THRESHOLD
SET
alarm zone
Min. level

Min. Min.
Alarm Alarm
RL2 “ON”
RL2 RL2 RL2 RL2
RL2 “OFF”
RL2 RL2 RL2 RL2

www.sgm-lektra.eu Page 21 of 40
 METER - quick setup

8.3 - ECHO MAP

Pressing LEFT ARROW, from RUN mode, to access directly to the echoes digital map display, which are in
METER receiving.
This function is useful for:
- properly orient the transducer pointing.
- verify the echoes in acquisition correctness.
- identify any false echo signals that may cause measurement errors.

Measured distance from Measure status

Echo frequency
METER in real time

D 721mm G 020 57.2KHz

Echo signal normalization

threshold

1 2 3 4 5
m

The rectangle placed at the echo line base, indicates

the measurement range within which the echo signal
in reception is considered always valid for the distance
measurement. This interval value is variable depending
on the measurement conditions: min. ± 2.5% of the
measured distance.

Page 22 of 40 www.sgm-lektra.com
 METER - advanced configuration

9-ADVANCED CONFIGURATION
9.1 - “SETUP” MENU

SET DISTANCE 4mA

0000mm
SETUP SET DISTANCE 4mA
SET DISTANCE 20mA
SET DISTANCE 20mA 0000mm
LIQUIDS
MEDIUM SOLIDS
LIQUIDS PIPE
FILTER COEFFICIENT
FILTER COEFFICENT VALUE
BLIND DISTANCE 000 0000mm
BLIND DISTANCE
ACTUAL LEVEL 4mA 0000mm VALUE >MIN
MAX
ACTUAL LEVEL 20mA OK to confirm MIN/MAX
DELAY
RELAY RL1 THRESHOLD DELAY 00 s
RL2 THRESHOLD SAFETY
>NO
ENABLE/DISABLE YES

MIN/MAX HYSTERESIS mm
>DISABLE
ENABLE
MIN/MAX HYSTERESIS mm
040 mm

VALUE
0000mm
UPPER VALUE
0000mm
LOWER
DELAY
RL1 PUMP DELAY 00 s

FILL./EMPT. >EMPTING
FILLING
ENABLE/DISABLE
>DISABLE
ENABLE

>DISABLE
RL2 DIAGNOSTIC
ENABLE

9.2 - SETUP

4321
D

mm

From “RUN” mode, holding down UP ARROW, press ENTER to the advanced con- ► SETUP
figuration mode access. DISPLAY
DIAGNOSTIC
SERVICE
INFO

Press SCROLL to select the menu and press ENTER to access. ► SET DISTANCE 4mA
SET DISTANCE 20mA
Press LEFT ARROW to exit.
FILTER TYPE
FILTER COEFFICIENT
BLIND DISTANCE
ACTUAL LEV. 4mA
ACTUAL LEV. 20mA
RELAYS

www.sgm-lektra.eu Page 23 of 40
 METER - advanced configuration
9.2.1 - SET DISTANCE 4mA ► SET DISTANCE 4mA
SET DISTANCE 20mA
Position the cursor on DISTANCE 4mA, press ENTER to access. FILTER TYPE
FILTER COEFFICIENT
BLIND DISTANCE
ACTUAL LEV. 4mA
ACTUAL LEV. 20mA
RELAYS

Use UP ARROW and SCROLL to modify the value.

Press ENTER to confirm. SET DISTANCE 4mA
LEFT ARROW to exit without changes

Default value: 6000mm (range 6m) or 10000mm (range 10m) 6000 mm

9.2.2 - SET DISTANCE 20mA SET DISTANCE 4mA
► SET DISTANCE 20mA
Position the cursor on DISTANCE 20mA, press ENTER to access. FILTER TYPE
FILTER COEFFICIENT
BLIND DISTANCE
ACTUAL LEV. 4mA
ACTUAL LEV. 20mA
RELAYS

Use UP ARROW and SCROLL to modify the value.

Press ENTER to confirm. SET DISTANCE 20mA
LEFT ARROW to exit without changes

Default value: 300mm (range 6m) or 500mm (range 10m) 0300 mm

9.2.3 - MEDIUM SET DISTANCE 4mA
SET DISTANCE 20mA
► FILTER TYPE
Position the cursor on MEDIUM, press ENTER to access.
FILTER COEFFICIENT
BLIND DISTANCE
ACTUAL LEV. 4mA
3 configurations are possible: ACTUAL LEV. 20mA
LIQUIDS - liquids measurement RELAYS
SOLIDS - granular solids measurement
LIQUIDS PIPE - liquids measurement in pipe reference MEDIUM
Press SCROLL to select the product type. ► LIQUIDS
Press ENTER to confirm.
LEFT ARROW to exit without changes SOLIDS

Default value: LIQUIDS LIQUIDS PIPE

9.2.4 - FILTER COEFFICIENT SET DISTANCE 4mA

SET DISTANCE 20mA
FILTER TYPE
Position the cursor on FILTER COEFFICIENT, press ENTER to access. ► FILTER COEFFICIENT
BLIND DISTANCE
ACTUAL LEV. 4mA
ACTUAL LEV. 20mA
RELAYS
Enter a value from 1 to 99: 1 maximum speed, 99 maximum slowness.
The function is deactivated with 0 (immediate response) FILTER COEFFICENT
Use UP ARROW and SCROLL to modify the value.
Press ENTER to confirm.
LEFT ARROW to exit without changes
20
Default value: 20

Page 24 of 40 www.sgm-lektra.com
 METER - advanced configuration
9.2.5 - BLIND DISTANCE SET DISTANCE 4mA
SET DISTANCE 20mA
Position the cursor on DISTANCE 4mA, press ENTER to access. FILTER TYPE
Represent the “BLIND ZONE” FILTER COEFFICIENT
► BLIND DISTANCE
ACTUAL LEV. 4mA
ACTUAL LEV. 20mA
Input the desired value in order to avoid measures near the surface of the sensor RELAYS
(if necessary).
The minimum value is 250mm (6m vers.) or 400mm (10m vers.)
Use UP ARROW and SCROLL to modify the value. BLIND DISTANCE
Press ENTER to confirm.
LEFT ARROW to exit without changes
0250 mm
Default values: 250mm (range 6m) or 400mm (range 10m)

9.2.6 - ACTUAL LEV. 4mA SET DISTANCE 4mA

SET DISTANCE 20mA
Position the cursor on ACTUAL LEV. 4mA, press ENTER to access. FILTER TYPE
FILTER COEFFICIENT
BLIND DISTANCE
► ACTUAL LEV. 4mA
ACTUAL LEV. 20mA
RELAYS

Self distance learning function that is associated with the 4mA (lower value).
Make sure that the level corresponds to 0%, ENTER to associate the actual meas-
ure with 4mA output value;
OK TO CONFIRM .
LEFT ARROW to exit without changes.

9.2.7 - ACTUAL LEV. 20mA SET DISTANCE 4mA

SET DISTANCE 20mA
Position the cursor on ACTUAL LEV. 20mA, press ENTER to access. FILTER TYPE
FILTER COEFFICIENT
BLIND DISTANCE
ACTUAL LEV. 4mA
► ACTUAL LEV. 20mA
RELAYS

Self distance learning function that is associated with the 20mA (upper value).
Make sure that the level corresponds to 100%, ENTER to associate the actual
measure with 20mA output value;
OK TO CONFIRM .
LEFT ARROW to exit without changes.

www.sgm-lektra.eu Page 25 of 40
 METER - advanced configuration
9.2.8 - RELAYS SET DISTANCE 4mA
SET DISTANCE 20mA
Position the cursor on RELAYS, press ENTER to access. FILTER TYPE
FILTER COEFFICIENT
BLIND DISTANCE
ACTUAL LEV. 4mA
ACTUAL LEV. 20mA
► RELAYS
In this sub-menù it’s possible to setup onboard relays (only 4-wires versions)
RL1 can be set as threshold relay or pump-control relay;
RL2 can be set as threshold relay or diagnostic relay. ► RL1 THRESHOLD
With the SCROLL button you can select the operation mode, then pressing EN- RL2 THRESHOLD
TER to confirm the selection RL1 PUMP

9.2.8.1 - RL1 THRESHOLD (RL2 THRESHOLD equivalent)

Position the cursor on RL1 THRESHOLD, press ENTER to access. ► RL1 THRESHOLD
RL2 THRESHOLD
RL1 PUMP

In this submenu you can set the set-point and the relay 1 and 2 action type
► VALUE
(only 4-wires versions). MIN/MAX
With the SCROLL button you can select the parameter to be programmed. DELAY
Press ENTER to confirm SAFETY
ANABLE/DISABLE
MIN/MAX HYSTERESIS

9.2.8.1.1 - VALUE
► VALUE
Position the cursor on VALUE, press ENTER to access. MIN/MAX
DELAY
SAFETY
ANABLE/DISABLE
MIN/MAX HYSTERESIS
It’s possible to input the threshold value that corresponds to the distance
in mm from the sensor.
Use UP ARROW and SCROLL to modify the value.
Press ENTER to confirm.
VALUE
LEFT ARROW to exit without changes

Default value: 0000mm 1000 mm
NB-RL1/2 inactive with 0000mm

9.2.8.1.2 - MIN/MAX
VALUE
► MIN/MAX
Position the cursor on VALUE, press ENTER to access.
DELAY
SAFETY
ANABLE/DISABLE
MIN/MAX HYSTERESIS

It’s possible to select if the relay works as maximum level threshold or mini-
mum level threshold.
With the SCROLL button you can select the operation mode.
Press ENTER to confirm. MIN
LEFT ARROW to exit without changes ► MAX

Default value: MAX for RL1; MIN for RL2

Page 26 of 40 www.sgm-lektra.com
 METER - advanced configuration
9.2.8.1.3 - DELAY
VALUE
Position the cursor on DELAY, press ENTER to access. MIN/MAX
► DELAY
SAFETY
ANABLE/DISABLE
MIN/MAX HYSTERESIS

It’s possible to set the activation delay for the selected relay, from 0 to 99 sec.
Use UP ARROW and SCROLL to modify the value.
Press ENTER to confirm. DELAY
LEFT ARROW to exit without changes

Default value: 00s 00 s
9.2.8.1.4 - SAFETY
VALUE
Position the cursor on SAFETY, press ENTER to access. MIN/MAX
DELAY
► SAFETY
ANABLE/DISABLE
A “safety alarm” provides a “closed” contact with relay energized in normal MIN/MAX HYSTERESIS
condition (no alarm), the contact switches to “open”:
- Alarm condition (eg overcoming MAX);
- In power failure case.
With the SCROLL button you can select the alarm mode.,
Press ENTER to confirm.
NO
LEFT ARROW to exit without changes
► YES

Default value: YES

9.2.8.1.5 - ENABLE/DISABLE
VALUE
Position the cursor on ENABLE/DISABLE, press ENTER to access. MIN/MAX
DELAY
SAFETY
► ANABLE/DISABLE
MIN/MAX HYSTERESIS

Select ENABLE to activate relay threshold.

Select DISABLE to not activate relay threshold.
With the SCROLL button you can select the operation mode.
Press ENTER to confirm.
DISABLE
LEFT ARROW to exit without changes ► ENABLE

Default value: DISABLE

9.2.8.1.6 - MIN/MAX HYSTERESIS mm

VALUE
MIN/MAX
Position the cursor on MIN/MAX HYSTERESIS mm, press ENTER to access.
DELAY
SAFETY
ANABLE/DISABLE
► MIN/MAX HYSTERESIS

It’s possible to input the threshold hysteresis.

Use UP ARROW and SCROLL to modify the value. MIN/MAX HYSTERESIS mm
Press ENTER to confirm.
LEFT ARROW to exit without changes

Default value: 40mm

040 mm

www.sgm-lektra.eu Page 27 of 40
 METER - advanced configuration
9.2.8.2 - RL1 PUMP (only for RL1)

Position the cursor on RL1 PUMP, press ENTER to access RL1 THRESHOLD
RL2 THRESHOLD
► RL1 PUMP

A pump control functioning activation, with hysteresis, is possible two thresh-

olds setting is required: ► UPPER
upper and lower threshold. LOWER
With the SCROLL button you can select the parameter to be programmed, DELAY
Press ENTER to confirm. FILL./EMPT.
ENABLE/DISABLE

9.2.8.2.1 - UPPER

Position the cursor on UPPER, press ENTER to access. ► UPPER

The upper threshold is expressed in mm distance from the sensor. Represents LOWER
the pump starting point, EMPTY case, or pump stopping point, FILLING case. DELAY
FILL./EMPT.
ENABLE/DISABLE

Use UP ARROW and SCROLL to modify the value.

Press ENTER to confirm. VALUE
LEFT ARROW to exit without changes

Default value: 0
0900 mm
9.2.8.2.2 - LOWER

Position the cursor on LOWER, press ENTER to access. UPPER

The lower threshold is expressed in mm distance from the sensor. Represents ► LOWER
the pump stopping point, EMPTY case, or pump starting point, FILLING case. DELAY
FILL./EMPT.
ENABLE/DISABLE

Use UP ARROW and SCROLL to modify the value.

Press ENTER to confirm. VALUE
LEFT ARROW to exit without changes

Default value: 0
4000 mm

FILLING EMPTING
900mm

UPPER UPPER
UPPER TH. TH.
THRESHOLD
4000mm

OFF ON OFF

OFF ON OFF

LOWER LOWER
LOWER TH. TH.
THRESHOLD

RL1 ON

RL1 OFF

Page 28 of 40 www.sgm-lektra.com
 METER - advanced configuration
9.2.8.2.3 - DELAY

Position the cursor on DELAY, press ENTER to access. UPPER

LOWER
► DELAY
FILL./EMPT.
ENABLE/DISABLE

Set the relay delay activation, from 0 to 99 sec. DELAY

Use UP ARROW and SCROLL to modify the value.
Press ENTER to confirm.
LEFT ARROW to exit without changes 05 s
Default value: 0
9.2.8.2.4 - FILL./EMPT

Position the cursor on DELAY, press ENTER to access. UPPER

LOWER
DELAY
► FILL./EMPT.
ENABLE/DISABLE

it’s possible to select the mode of pump control (FILLING or EMPTING)

With the SCROLL button you can select the operation mode.
Press ENTER to confirm.
LEFT ARROW to exit without changes ► EMPTING
FILLING
Default value: EMPTING

9.2.8.2.5 - ENABLE/DISABLE

Position the cursor on ENABLE/DISABLE, press ENTER to access. UPPER

LOWER
DELAY
FILL./EMPT.
► ENABLE/DISABLE
Select ENABLE to activate relay threshold.
Select DISABLE to not activate relay threshold.
With the SCROLL button you can select the operation mode.
Press ENTER to confirm.
LEFT ARROW to exit without changes ► DISABLE
ENABLE
Default value: DISABLE

9.2.8.3 - RL2 DIAGNOSTIC

Position the cursor on RL2 DIAGNOSTIC, press ENTER to access. RL1 THRESHOLD
RL2 THRESHOLD
If it becomes necessary the METER functional control, it’s possible to enable the RL1 PUMP
► RL2 DIAGNOSTIC
RL2 alarm output function. In this case, enabling the function, RL2 is energized
in normal operation (RL2 LED on) and is de-energized (LED RL2 off, safety alarm)
when at least one of the four conditions mentioned below, shall be verified:
- TEMP. : temperature out of range
- ECHO : no echo is detected
- GAIN : the sensor’s gain exceed the value setted in Max Gain TH (7.3.5) ► DISABLE
- DIST. : the measured distance exceed the 120% of the maximum ENABLE
distance in setup
Select ENABLE to activate relay threshold.
Select DISABLE to not activate relay threshold.
With the SCROLL button you can select the operation mode.
Press ENTER to confirm.
LEFT ARROW to exit without changes
Default value: DISABLE
when an error occurs, a “!” is flashing on the display: press SCROLL to show a
message that indicate what kind of error is present. The METER automatically
returns to RUN mode.

www.sgm-lektra.eu Page 29 of 40
 METER - advanced configuration
9.3 “DISPLAY” menu

>1 VALUE DISTANCE mm

DISPLAY DISPLAY VALUES 2 VALUES LEVEL mm
LEVEL %
OUTPUT mA
1 VALUE TEMPERATURE °C
>2 VALUES
>PRIMARY VALUE DISTANCE mm
SECONDARY VALUE LIVEL mm
LCD CONTRAST
LCD CONTRAST 00 LIVEL %
PRIMARY VALUE OUTPUT mA
WELCOME TEXT >SECONDARY VALUE TEMPERATURE °C
WELCOME TEXT SGM-LEKTRA METER

9.4 - DISPLAY
SETUP
► DISPLAY
From “RUN” mode, holding down UP ARROW, press ENTER to access DIAGNOSTIC
Position the cursor on DISPLAY and press ENTER SERVICE
INFO

Select the parameters by moving the cursor with SCROLL and confirm with ENTER ► DISPLAY VALUES
LCD CONTRAST
WELCOME TEXT

9.4.1 - DISPLAY VALUES

► DISPLAY VALUES
LCD CONTRAST
Position the cursor on DISPLAY VALUES, press ENTER to access. WELCOME TEXT

It’s possible to select if one value with big digits or two values are shown on the
display in “RUN” mode.
Select the parameters by moving the cursor with SCROLL and confirm with ► 1 VALUE
ENTER. 2 VALUES
LEFT ARROW to exit without changes

9.4.1.1 - 1 VALUE

Position the cursor on 1 VALUE, press ENTER to access.

► 1 VALUE
2 VALUES

Only one value is displayed; it’s possible to choose from 5 parameters. ► DISTANCE mm
With the SCROLL button you can select data to display. LEVEL mm
Press ENTER to confirm. LEVEL %
LEFT ARROW to exit without changes OUTPUT mA

4321
D

mm

Page 30 of 40 www.sgm-lektra.com
 METER - advanced configuration

9.4.1.2 - 2 VALUE

Position the cursor on 2 VALUE, press ENTER to access.

1 VALUE
► 2 VALUES

Two values are displayed; it’s possible to choose which one is the primary and
which is the secondary, each with a choice of 5 parameters.
With the SCROLL button you can select data to display. ► PRIMARY VALUE
Press ENTER to confirm. SECONDARY VALUE
LEFT ARROW to exit without changes

► DISTANCE mm
LEVEL mm
LEVEL %
OUTPUT mA

PRIMARY VALUE
► SECONDARY VALUE

DISTANCE mm
► LEVEL mm
LEVEL %
OUTPUT mA
TEMPERATURE °C

9.4.2 - LCD CONTRAST

DISPLAY VALUES
► LCD CONTRAST
Position the cursor on LCD CONTRAST, press ENTER to access. WELCOME TEXT

it’s possible to adjust the contrast of LCD, simply increasing or decreasing the
value of a parameter from 0 to 63. LCD CONTRAST
Use UP ARROW and SCROLL to modify the value.
Press ENTER to confirm.
LEFT ARROW to exit without changes 22
Default value: 32

www.sgm-lektra.eu Page 31 of 40
 METER - advanced configuration

9.4.3 - WELCOME TEXT

DISPLAY VALUES
LCD CONTRAST
Position the cursor on WELCOME TEXT, press ENTER to access.
► WELCOME TEXT

It’s possible to edit or delete the message that is displayed by the METER during
the ignition phase.
Use UP ARROW (up scroll) and SCROLL (down scroll) to change the digit; ENTER WELCOME TEXT
to move the digit to the right. To confirm press ENTER repeatedly until leave the
parameter.
LEFT ARROW to exit without changes
SGM-LEKTRA
METER
Default value: SGM-LEKTRA METER

Page 32 of 40 www.sgm-lektra.com
 METER - advanced configuration

9.5 “DIAGNOSTIC” menu

TEMPERATURE
NO ECHO FOUND
DIAGNOSTIC ALARM CONFIGURATION MAX GAIN DISABLE
ECHO IN BLIND >ENABLE
DISTANCE >120%

MEASURE STATUS MEASURE STATUS

G : 00000

FROZEN GAIN FROZEN GAIN

000

MAX GAIN TH. MAX GAIN TH

200
PEAK VALUES
PEAK VALUES >DISPLAY VALUES Max 0000mm
RESET VALUES Min 0000mm
OUTPUT SIMUL
OUTPUT SIMUL
00.0mA

9.6 - DIAGNOSTIC
SETUP
DISPLAY
From “RUN” mode, holding down UP ARROW, press ENTER to access ► DIAGNOSTIC
Position the cursor on DIAGNOSTIC and press ENTER SERVICE
INFO

Select the parameters by moving the cursor with SCROLL and confirm with ENTER ► ALARM CONFIGURATION
MEASURE STATUS
FROZEN GAIN
MAX GAIN TH.
PEAK VALUES
OUTPUT SIMUL.

9.6.1 - ALARM CONFIGURATION ► ALARM CONFIGURATION

MEASURE STATUS
Position the cursor on ALARM CONFIGURATION, press ENTER to access FROZEN GAIN
MAX GAIN TH.
PEAK VALUES
To enable or disable each diagnostic alarms. OUTPUT SIMUL.

- with UP ARROW or SCROLL chose the desired item and press ENTER ► TEMPERATURE
NO ECHO FOUND
MAX GAIN
ECHO IN BLIND
DISTANCE >120%

- with UP ARROW or SCROLL enable or disable the alarm signal and

press ENTER to confirm

DISABLE
► ENABLE

www.sgm-lektra.eu Page 33 of 40
 METER - advanced configuration
9.6.2 - MEASURE STATUS ALARM CONFIGURATION
► MEASURE STATUS
Position the cursor on MEASURE STATUS, press ENTER to access. FROZEN GAIN
MAX GAIN TH.
PEAK VALUES
OUTPUT SIMUL.

It’s possible to display the gain of the system, with values from 0 to 255.
LEFT ARROW to exit MEASURE STATUS

G: 00000
9.6.3 - FROZEN GAIN
ALARM CONFIGURATION
MEASURE STATUS
Position the cursor on MEASURE STATUS, press ENTER to access. ► FROZEN GAIN
MAX GAIN TH.
PEAK VALUES
OUTPUT SIMUL.
It’s possible to fix a value of gain (from 1 to 255) and consequently disable the
automatic gain control. Once the value is 000 the automatic gain control re-
starts.
Use UP ARROW and SCROLL to modify the value.
FROZEN GAIN
Press ENTER to confirm.
LEFT ARROW to exit without changes
000
Default value: 000
9.6.4 - MAX GAIN TH ALARM CONFIGURATION
MEASURE STATUS
Position the cursor on MAX GAIN TH, press ENTER to access. FROZEN GAIN
► MAX GAIN TH.
PEAK VALUES
OUTPUT SIMUL.
It’s possible to change the max value of gain. If the gain reaches this value, the
“GAIN” error code is activated
Use UP ARROW and SCROLL to modify the value.
Press ENTER to confirm.
MAX GAIN TH
LEFT ARROW to exit without changes

Default value: 200

255
9.6.5 - PEAK VALUES ALARM CONFIGURATION
MEASURE STATUS
Position the cursor on PEAK VALUES, press ENTER to access. FROZEN GAIN
MAX GAIN TH.
► PEAK VALUES
OUTPUT SIMUL.

The system store the maximum distance and the minimum distance measured
since the power is turned ON.
It’s possible to see those values or reset the values. ► DISPLAY VALUES
With the SCROLL button you can select the function.
Press ENTER to confirm. RESET VALUES

Page 34 of 40 www.sgm-lektra.com
 METER - advanced configuration
9.6.5.1 - DISPLAY VALUES

Position the cursor on DISPLAY VALUES, press ENTER to access.

► DISPLAY VALUES

RESET VALUES

Displays the max. and min. distance measured from power on.
LEFT ARROW to exit. PEAK VALUES
NB - The peak values stored are erased every time the METER turns-off
MAX 0000mm

MIN 0000mm

9.6.5.2 - RESET VALUES

Position the cursor on RESET VALUES, press ENTER to access.

DISPLAY VALUES

LEFT ARROW to return to the previous menu ► RESET VALUES

9.6.6 - OUTPUT SIMULATION ALARM CONFIGURATION

MEASURE STATUS
WARNING - entering in the SIMULATION function, the current output is not FROZEN GAIN
in function of the level measurement. To restore the current as a measured level MAX GAIN TH.
function, press the LEFT ARROW button 3 times (RUN mode) PEAK VALUES
► OUTPUT SIMUL.
Position the cursor on OUTPUT SIMULATION, press ENTER to access.

It’s possible to force the analog output to a desired value, from 3,5 to 21mA. OUTPUT SIMUL.
Use UP ARROW and SCROLL to modify the value.
LEFT ARROW to return to the previous menu.
04.0mA

www.sgm-lektra.eu Page 35 of 40
 METER - advanced configuration
9.7 “SERVICE” menu

21.5 mA
SERVICE OUTPUT SAFE MODE 3.85 mA
>HOLD LAST VALUE

SET UID SET UID

000

ENGLISH
LANGUAGE >ITALIANO
FRANCAIS

FREQUENCY FREQUENCY
00.0 kHz

F_WINDOW F_WINDOW
00

RESTORE SETTINGS OK TO CONFIRM

9.8 - SERVICE
SETUP
DISPLAY
From “RUN” mode, holding down UP ARROW, press ENTER to access DIAGNOSTIC
Position the cursor on SERVICE and press ENTER ► SERVICE
INFO

Select the parameters by moving the cursor with SCROLL and confirm with ENTER ► OUTPUT SAFE MODE
SET UID
LANGUAGE
F_WINDOW
RESTORE SETTING
BLUETOOTH

9.8.1 - OUTPUT SAFE MODE ► OUTPUT SAFE MODE

SET UID
Position the cursor on OUTPUT SAFE MODE, press ENTER to access. LANGUAGE
F_WINDOW
RESTORE SETTING
It’s possible to choose a analog output value during diagnostic errors. BLUETOOTH
“21.5 mA” forces the current output to 21,5mA
“3.85 mA” forces the current output to 3,85mA
”HOLD LAST VALUE” maintains the output at the last valid value.
► 21.5 mA
With the SCROLL button you can select the operation mode.
Press ENTER to confirm. 3.85 mA
LEFT ARROW to exit without changes
HOLD LAST VALUE
Default value: HOLD LAST VALUE

9.8.2 - SET UID OUTPUT SAFE MODE

► SET UID
Position the cursor on SET UID, press ENTER to access. LANGUAGE
F_WINDOW
Can assign the address UID in this parameter, for a MUDBUS RTU RESTORE SETTING
network. BLUETOOTH

Use UP ARROW and SCROLL to modify the value. SET UID

Press ENTER to confirm.
LEFT ARROW to exit without changes

Default value 001

001

Page 36 of 40 www.sgm-lektra.com
 METER - advanced configuration

9.8.3 - LANGUAGE OUTPUT SAFE MODE

SET UID
Position the cursor on LANGUAGE, press ENTER to access. ► LANGUAGE
F_WINDOW
Sets the menu language: English, Italian, French RESTORE SETTING
BLUETOOTH

Press SCROLL to select the menu language.

Press ENTER to confirm. ENGLISH
► ITALIANO
LEFT ARROW to exit without changes
FRANCAIS

9.8.4 - FREQUENCY OUTPUT SAFE MODE

SET UID
Position the cursor on FREQUENCY, press ENTER to access. LANGUAGE
► FREQUENCY
It’s possible to check the computed sensor emission frequency. F_WINDOW
RESTORE SETTING

LEFT ARROW to exit without changes

FREQUENCY

00.0 kHz
9.8.5 - F_ WINDOWS OUTPUT SAFE MODE
SET UID
Position the cursor on F_WINDOWS, press ENTER to access. LANGUAGE
► F_WINDOW
It is the increase value (in cm), step to step, of the window width during the echo RESTORE SETTING
signal research phase. BLUETOOTH
The “F_WINDOWS” is the area where the echo reception is active.
Normally it is positioned around the real echo signal and all echoes detected
within the F_WINDOW are deemed valid.
SET WIDTH
Example: F_WINDOW parameter set to 5.
- The METER detects an echo signal which is 4 meters from the sensor.
- Suddenly, the echo signal disappears and a new echo signal to 3.5 mt
away from the sensor is detected.
05
- Each time the echo signal will be emitted, the METER will enlarge
“F_WINDOW” with 5cm step, until covering the new eco detected area.
Now the F_WINDOW will start to tighten around the new echo signal and
the new measurement of 3,5mt distance will be used to calculate the level
measurement, alarm thresholds, etc..
F_WINDOW serves to filter false echo signals products, for example, by the agita-
tor blades
Range: 05÷20
Use UP ARROW and SCROLL to modify the value.
Press ENTER to confirm.
LEFT ARROW to exit without changes

Default value: 05 (2 wires versions) e 10 (4 wires versions)

www.sgm-lektra.eu Page 37 of 40
 METER - advanced configuration

9.8.6 - RESTORE SETTING OUTPUT SAFE MODE

SET UID
Position the cursor on SET UID, press ENTER to access. LANGUAGE
F_WINDOW
► RESTORE SETTING
BLUETOOTH

Press ENTER to restore the METER default settings

LEFT ARROW to exit without restored the METER default settings OK TO CONFIRM

9.8.7 “INFO” menu

SGM-LEKTRA
METER
INFO
FIRMWARE REV.
IC

9.8.8 - INFO SETUP

DISPLAY
Position the cursor on INFO, press ENTER to access. DIAGNOSTIC
SERVICE
► INFO

In addition to information about the manufacturer, are displayed the SGM-LEKTRA

firmware revision and the configuration index METER
FIRMWARE REV.
I.C.

Page 38 of 40 www.sgm-lektra.com
www.sgm-lektra.eu Page 39 of 40
 Documentation subject to technical change with no prior warning

10-FACTORY TEST AND QUALITY CERTIFICATE

In conformity to the company and check procedures I certify that the equipment:

(Ultrasonic sensor)

is conform to the technical requirements on Technical Data and it is made in conformity to the procedure

Quality Control Manager: .......................................................... Production and check date: .................................................

SGM-LEKTRA S.r.l.
Via Papa Giovanni XXIII, 49
20090 Rodano (MI) - ITALY
tel: ++39 02 95328257
fax: ++39 02 95328321
e-mail: [email protected]
web: sgm-lektra.com