Phuentsholing Township Development Project (PTDP),

PROJECT NAME
Phuentsholing, Bhutan.

CLIENT CONSTRUCTION DEVELOPMENT CORPORATION LTD.

CONSULTANT EGIS INTERNATIONAL IN J.V WITH EGIS INDIA

DESIGN
SANGUINE INFRATECH PVT LTD
CONSULTANT

CONTRACTOR /
KALIKA RIGSAR JOINT VENTURE
CONSULTANT

DOCUMENT NO. DESIGN OF COMPOUND WALL

Contractor / Rev. R0
Consultant Document CDCL/SANGUINE/CW/DN-100
No.

PREPARED CHECKED APPROVED

REV.
DATE DESCRIPTION BY BY BY
NO.
Init. Sign Init. Sign Init. Sign
R0 22.06.2023 ISSUED FOR APPROVAL DG ABJ DMK

This Document is the property of Sanguine. It should not be used, copied or reproduced without their written permission.

Page 1 of 30
 CONTENT
Cl. Description No. Page
No.

1. Introduction of compound wall 3

2. Design Calculations of Compound wall 4

2.1 Input data 4
2.2 Loading calculation 4
2.3 Design Calculations 7
2.3.1 STAAD input File 7
2.3.2 Snaps of STAAD Model 9
2.3.3 Design of Isolated footing 11
2.3.4 Design of RCC Columns 15
2.3.5 Design of Ground Beam 16
2.3.6 Design of Coping Beam 20

3. References 24

4. List of Drawings 24

ANNEXURE LIST
i. Annexure A - Design Output of RCC Column 25
ii. Annexure B - BMD & SFD of Beams 30

Page 2 of 30
1 INTRODUCTION
Compound wall is analysed with RC beam & column arrangement at a 3m center to centre spacing. Two
columns are tied with ground beam and coping beam at top. RCC framing is filled with brick wall and
protected with barbed wire at top. There is very dense grayish brown medium sand varying from 12m to
21 m below existing ground level throughout the site. Staad software is used to prepare model for above
said configuration framing and analysed for further design of structure. Model is prepared for five column
and four bay framing of wall and maximum support reaction is taken for design of structural RCC
elements. i.e. Footing, Column, Beam etc.

Page 3 of 30
 2 Design Calculations of Compound wall

2.1 INPUT DATA

2.1.1 RCC framing above Natural ground level
Grade of concrete M30
Grade of Reinforcement bar Fe500 TMT Corrosion Resistant Steel
for mild steel Fe415
height of column 2.4 m
Size of column 0.25 x 0.35 m
C/C Spacing of the two column 3.0 m
Height of Brick wall over ground beam 2.275 m
Size of the Ground beam 0.23 x 0.30 m
Size of the Coping beam 0.28 x 0.125 m

2.1.2 RCC framing below Natural ground level

Size of Isolated Footing 1.0 m x 1.0 m

Size of Combined Footing 1.5 m x 1.5 m
Depth of the footing 1.10 m below FGL
Net SBC for design 30 T/Sqm at 1.1 m below FGL

2.2 LOADING CALCULATION

2.2.1 Load 1 – Self Weight (DL)

This load case consists of self-weight of the structure and Self-weight is applied using the
STAAD in-built command.

2.2.2 Load 2 - Dead Load

Uniformly distributed load of brick wall over beam
UDL of ground beam = 2.275m x 0.23m x 20 = 10.47 kN/m ≈ 11.0 kN/m

Concertina barbed coil wt on column:

Take 8.5kg/730mm coil wt and for 3 meter
0.35 kN ≈ 0.5kN on column
Length
Wt of ground beam = 0.23 x 0.20 x 25 = 1.73 kN/m
Wt of Coping beam = 0.28 x 0.2 x 25 = 0.88 kN/m

2.2.3 Load 3 - Live load

Live load is considered as very low value while construction stage loading only
1.00 kN/m

2.2.4 Load 4 - Wind Load

Wind force on structure shall be taken in accordance with IS: 875-1987 as applicable
Basic Design speed is 27.78 m/s in site location.
Design Wind Speed (Vz),
Vz = Vb x k1 x k2 x k3 ;

where, Vz = Design wind speed at any height in m/s

Vb = Basic wind speed at any height in m/s
K1 = Probability factor (risk coefficient)
K2 = Terrain height and structure size factor
K3 = Topographic factor

K1 = 0.82 (Table 1)
K2 = 0.91 Category 3
K3 = 1.00 Slope 0
K4 = 1.00

Vz = 27.78 x 0.82 x 0.91 x 1x 1 = 20.73m/s at 5.0m height

Design wind pressure is given by at height z

2
Pz = 0.6(Vz)^2 = 0.6 x (20.73)^2 = 257.83 N/m = 0.26 kN/m2

The design wind pressure Pd can be obtained as,

Page 4 of 30
 Pd = Kd Ka.Kc Pz
where
Kd = wind directionality factor, = 1.0
Ka = area averaging factor, and = 1.0 Tributory area <10sqm
Kc = combination factor = 1

Design wind pressure, Pd = 1x1x1 x Pz

= 1 x Pz
2
= 0.258 kN/m

Wind pressure is calculated at maximum 5 m depth by using wind parameters. Same wind
Note:- Wind pressure below the 10m is not applicable as per the codal provision. On higher
side, compound wall is designed for wind load.

2.2.5 Load 5 – Earthquake Load

Considered of Phuentsholing district.

Z = 0.36 Zone V
R=5 Moment resistance frame with shear wall
I=1 For Compound wall
SS = 3, Net SBC is 30 T/m2 for soil type of soft soil

B= 0.5 m Tentative Width of structure

L= 10 m Tentative Length of the structure.
***ZONE 0.36 RF 5 I 1 SS 3 ST 1 DM 0.05 PX 0.318 PZ 0.071
I= 1
Z= 0.36
R= 5
H= 2.5 m
Px = 0.32 sec
Pz = 0.07 sec
Sa/g = 2.5

Seismic Horizontal coefficient, Ah = (I /R ) x (Z / 2) x (Sa/g) = 0.09

Page 5 of 30
 Lump weight of structure Seismic weight
Node L/C Force-Y kN Node L/C Force-Y kN
1 99 22.3 1 99 2.007
2 99 4.4 2 99 0.396
3 99 43.9 3 99 3.951
4 99 5.7 4 99 0.513
5 99 42.8 5 99 3.852
6 99 5.8 6 99 0.522
7 99 43.9 7 99 3.951
8 99 5.7 8 99 0.513
9 99 22.3 9 99 2.007
10 99 4.4 10 99 0.396

LOAD 5 TITLE SISC X+VE (WITH LL)

JOINT LOAD
1 FZ -2.02
2 FZ -0.4
3 FZ -3.96
4 FZ -0.52
5 FZ -3.86
6 FZ -0.54
7 FZ -3.96
8 FZ -0.52
9 FZ -2.02
10 FZ -0.4

2.2.6 Load Combinations

Following load combination are calculated as per IS 1893 : 2000 Part - I and Clause no 6.3.1.2
A) Load Combination for Column & Beam_ Limit State design
LOAD COMB 100 1.5DL+1.5LL
LOAD COMB 101 1.2DL+1.2LL+1.2EQZ
LOAD COMB 102 1.2DL+1.2LL-1.2EQZ
LOAD COMB 103 1.2DL+1.2LL+1.2WLZ
LOAD COMB 104 1.2DL+1.2LL-1.2WLZ
LOAD COMB 105 1.5DL+1.5EQZ
LOAD COMB 106 1.5DL -1.5EQZ
LOAD COMB 107 0.9DL+1.5EQZ
LOAD COMB 108 0.9DL-1.5EQZ

B) Load combinations for Footing Design Base pressure calculation (Unfactored combination)
LOAD COMB 200 1.0(DL)
LOAD COMB 201 1.0DL+1.0IL+1.0EQZ
LOAD COMB 202 1.0DL+1.0IL-1.0EQZ
LOAD COMB 203 1.0DL+1.0IL+1.0WLZ
LOAD COMB 204 1.0DL+1.0IL-1.0WLZ
LOAD COMB 205 1.0DL+1.0EQZ
LOAD COMB 206 1.0DL-1.0EQZ
LOAD COMB 207 1.0DL+1.0WLZ
LOAD COMB 208 1.0DL-1.0WLZ

Page 6 of 30
2.3 DESIGN CALCULATION

2.3.1 STAAD INPUT FILE

STAAD SPACE
START JOB INFORMATION
ENGINEER DATE 16/06/2023
JOB NAME Compound wall
JOB CLIENT PTDP-KRJV
JOB REV R0
ENGINEER NAME DG
CHECKER NAME ABJ
APPROVED NAME DMK
CHECKER DATE 17/06/2023
END JOB INFORMATION
INPUT WIDTH 79
UNIT METER KN
JOINT COORDINATES
1 0 0 0; 2 0 2.4 0; 3 3 0 0; 4 3 2.4 0; 5 6 0 0; 6 6 2.4 0; 7 9 0 0; 8 9 2.4 0;
9 12 0 0; 10 12 2.4 0; 11 0 -0.6 0; 12 3 -0.6 0; 13 6 -0.6 0; 14 9 -0.6 0;
15 12 -0.6 0;
MEMBER INCIDENCES
1 1 2; 2 1 3; 3 2 4; 4 3 5; 5 4 6; 6 5 7; 7 6 8; 8 7 9; 9 8 10; 10 3 4; 11 5 6;
12 7 8; 13 9 10; 14 1 11; 15 3 12; 16 5 13; 17 7 14; 18 9 15;
DEFINE MATERIAL START
ISOTROPIC CONCRETE
E 2.73818e+07
POISSON 0.17
DENSITY 25
ALPHA 1e-05
DAMP 0.05
TYPE CONCRETE
STRENGTH FCU 30000
END DEFINE MATERIAL
MEMBER PROPERTY INDIAN
1 10 TO 18 PRIS YD 0.25 ZD 0.35
2 4 6 8 PRIS YD 0.3 ZD 0.23
3 5 7 9 PRIS YD 0.125 ZD 0.28
CONSTANTS
MATERIAL CONCRETE ALL
SUPPORTS
11 TO 15 FIXED
**1 TO 10 PINNED
DEFINE WIND LOAD
TYPE 1 WIND 1
INT 0.258 0.258 HEIG 0 3
EXP 1 JOINT 1 TO 10
LOAD 1 LOADTYPE Dead TITLE SELF WEIGHT
SELFWEIGHT Y -1
LOAD 2 LOADTYPE Dead TITLE DEAD LOAD
****Dead load on ground beam*********
****UDL ofkN/m
ground
? beam 11.0
= 2.275m
kN/m x 0.23m x 20 = 10.46
MEMBER LOAD
2 4 6 8 UNI GY -11
*******Concertina barbed coil weight on column =
***Take 8.5kg/730mm coil wt & for 3m Length=(8.5*3+10)*9.81/1000
JOINT LOAD
2 4 6 8 10 FY -0.5
LOAD 3 LOADTYPE Live TITLE LIVE LOAD
MEMBER LOAD
2 4 6 8 UNI GY -1
LOAD 4 LOADTYPE Wind TITLE WIND LOAD
WIND LOAD Z -1 TYPE 1 XR 0 12 YR 0 2.4 ZR -0.1 0.1
LOAD 5 LOADTYPE Seismic TITLE SISC Z+VE (WITH LL)
JOINT LOAD
1 FZ -2.02
2 FZ -0.4

Page 7 of 30
3 FZ -3.96
4 FZ -0.52
5 FZ -3.86
6 FZ -0.54
7 FZ -3.96
8 FZ -0.52
9 FZ -2.02
10 FZ -0.4
************************************************
*******LOAD COMB. 99 IS USED FOR SEISMIC WEIGHT CALCULATION IN Z DIR. ONLY**
**LOAD COMB 99 EL
**1 1.0 2 1.0 3 0.5
*******Load Combination for Column & Beam_ Limit State design
********(IS 1893, Cl 6.3.1.2)
LOAD COMB 100 1.5DL+1.5LL
1 1.5 2 1.5 3 1.5
LOAD COMB 101 1.2DL+1.2LL+1.2EQZ
1 1.2 2 1.2 3 1.2 5 1.2
LOAD COMB 102 1.2DL+1.2LL-1.2EQZ
1 1.2 2 1.2 3 1.2 5 -1.2
LOAD COMB 103 1.2DL+1.2LL+1.2WLZ
1 1.2 2 1.2 3 1.2 4 1.2
LOAD COMB 104 1.2DL+1.2LL-1.2WLZ
1 1.2 2 1.2 3 1.2 4 -1.2
LOAD COMB 105 1.5DL+1.5EQZ
1 1.5 2 1.5 5 1.5
LOAD COMB 106 1.5DL -1.5EQZ
1 1.5 2 1.5 5 -1.5
LOAD COMB 107 0.9DL+1.5EQZ
1 0.9 2 0.9 5 1.5
LOAD COMB 108 0.9DL-1.5EQZ
1 0.9 2 0.9 5 -1.5
**********************************************************
*******Load combinations for Footing Design Base pressure
*******calculation (Unfactored Load combination)
LOAD COMB 200 1.0(DL)
1 1.0 2 1.0
LOAD COMB 201 1.0DL+1.0IL+1.0EQZ
1 1.0 2 1.0 3 1.0 5 1.0
LOAD COMB 202 1.0DL+1.0IL-1.0EQZ
1 1.0 2 1.0 3 1.0 5 -1.0
LOAD COMB 203 1.0DL+1.0IL+1.0WLZ
1 1.0 2 1.0 3 1.0 4 1.0
LOAD COMB 204 1.0DL+1.0IL-1.0WLZ
1 1.0 2 1.0 3 1.0 4 -1.0
LOAD COMB 205 1.0DL+1.0EQZ
1 1.0 2 1.0 5 1.0
LOAD COMB 206 1.0DL-1.0EQZ
1 1.0 2 1.0 5 -1.0
LOAD COMB 207 1.0DL+1.0WLZ
1 1.0 2 1.0 4 1.0
LOAD COMB 208 1.0DL-1.0WLZ
1 1.0 2 1.0 4 -1.0
PERFORM ANALYSIS PRINT STATICS CHECK
LOAD LIST 100 TO 108
START CONCRETE DESIGN
CODE INDIAN
FC 30000 MEMB 1 10 TO 18
FYMAIN 500000 MEMB 1 10 TO 18
FYSEC 415000 MEMB 1 10 TO 18
MAXMAIN 10 MEMB 1 10 TO 18
RATIO 4 MEMB 1 10 TO 18
DESIGN COLUMN 1 10 TO 18
END CONCRETE DESIGN
FINISH

Page 8 of 30
2.3.2 Snaps of STAAD Model

As per input data and loading calculation, staad model is prepared. Followings are snaps to
elaborate the anlysis and design steps.

Figure -1 - Typical plan & section of compound wall.

Figure -2 - Member number and Node number

Figure -3 - Three dimensional view of structure.

Page 9 of 30
Figure -4 - Basic load values on the wall.

Page 10 of 30
 2.3.3 DESIGN OF ISOLATED FOOTING

2.3.3.1 STAAD REACTION SUMMARY TO CALCULATE FOOTING SIZE

Horizontal Vertical Horizontal Moment
Force-X Force-Y Force-Z Moment- Moment- Moment- FOOTING tentative P/A+M/Zx+ P/A-M/Zx- EQ Col. Fdn
Node L/C SIZE P/A M/Zx M/Zy SBC CHECK Ratio
kN kN kN X kN-m Y kN-m Z kN-m Depth M/Zy M/Zy FACTOR No No
11 200 8.6 26.4 0 0 0 -0.1 1 1 0.2 27.8 0.0 -0.6 27.2 28.4 300 1 SAFE 0.09 C1 F1
201 9.2 27.8 2.5 2.6 -0.1 -0.1 1 1 0.2 29.2 15.6 -0.6 44.2 14.2 300 1.25 SAFE 0.12 F1
202 9.2 27.8 -2.5 -2.6 0.1 -0.1 1 1 0.2 29.2 -15.6 -0.6 13.0 45.4 300 1.25 SAFE 0.12 F1
203 9.2 27.8 1 2 -0.1 -0.1 1 1 0.2 29.2 12.0 -0.6 40.6 17.8 300 1.25 SAFE 0.11 F1
204 9.2 27.8 -1 -2 0.1 -0.1 1 1 0.2 29.2 -12.0 -0.6 16.6 41.8 300 1.25 SAFE 0.11 F1
205 8.6 26.4 2.5 2.6 -0.1 -0.1 1 1 0.2 27.8 15.6 -0.6 42.8 12.8 300 1.25 SAFE 0.11 F1
206 8.6 26.4 -2.5 -2.6 0.1 -0.1 1 1 0.2 27.8 -15.6 -0.6 11.6 44.0 300 1.25 SAFE 0.12 F1
207 8.6 26.4 1 2 -0.1 -0.1 1 1 0.2 27.8 12.0 -0.6 39.2 16.4 300 1.25 SAFE 0.10 F1
208 8.6 26.4 -1 -2 0.1 -0.1 1 1 0.2 27.8 -12.0 -0.6 15.2 40.4 300 1.25 SAFE 0.11 F1
12 200 -3.2 48.9 0 0 0 0.9 1 1 0.2 50.3 0.0 5.4 55.7 44.9 300 1 SAFE 0.19 C2 F1
201 -3.5 52 4.4 3.8 0 1 1 1 0.2 53.4 22.8 6.0 82.2 24.6 300 1.25 SAFE 0.22 F1
202 -3.5 52 -4.4 -3.8 0 1 1 1 0.2 53.4 -22.8 6.0 36.6 70.2 300 1.25 SAFE 0.19 F1
203 -3.5 52 1.8 3 -0.1 1 1 1 0.2 53.4 18.0 6.0 77.4 29.4 300 1.25 SAFE 0.21 F1
204 -3.5 52 -1.8 -3 0.1 1 1 1 0.2 53.4 -18.0 6.0 41.4 65.4 300 1.25 SAFE 0.17 F1
205 -3.2 48.9 4.4 3.8 0 0.9 1 1 0.2 50.3 22.8 5.4 78.5 22.1 300 1.25 SAFE 0.21 F1
206 -3.2 48.9 -4.4 -3.8 0 0.9 1 1 0.2 50.3 -22.8 5.4 32.9 67.7 300 1.25 SAFE 0.18 F1
207 -3.2 48.9 1.8 3 -0.1 0.9 1 1 0.2 50.3 18.0 5.4 73.7 26.9 300 1.25 SAFE 0.20 F1
208 -3.2 48.9 -1.8 -3 0.1 0.9 1 1 0.2 50.3 -18.0 5.4 37.7 62.9 300 1.25 SAFE 0.17 F1
13 200 0 47.8 0 0 0 0 1 1 0.2 49.2 0.0 0.0 49.2 49.2 300 1 SAFE 0.16 C3 F1
201 0 50.8 4.4 3.9 0 0 1 1 0.2 52.2 23.4 0.0 75.6 28.8 300 1.25 SAFE 0.20 F1
202 0 50.8 -4.4 -3.9 0 0 1 1 0.2 52.2 -23.4 0.0 28.8 75.6 300 1.25 SAFE 0.20 F1
203 0 50.8 1.9 3.3 0 0 1 1 0.2 52.2 19.8 0.0 72.0 32.4 300 1.25 SAFE 0.19 F1
204 0 50.8 -1.9 -3.3 0 0 1 1 0.2 52.2 -19.8 0.0 32.4 72.0 300 1.25 SAFE 0.19 F1
205 0 47.8 4.4 3.9 0 0 1 1 0.2 49.2 23.4 0.0 72.6 25.8 300 1.25 SAFE 0.19 F1
206 0 47.8 -4.4 -3.9 0 0 1 1 0.2 49.2 -23.4 0.0 25.8 72.6 300 1.25 SAFE 0.19 F1
207 0 47.8 1.9 3.3 0 0 1 1 0.2 49.2 19.8 0.0 69.0 29.4 300 1.25 SAFE 0.18 F1
208 0 47.8 -1.9 -3.3 0 0 1 1 0.2 49.2 -19.8 0.0 29.4 69.0 300 1.25 SAFE 0.18 F1

SANGUINE INFRA TECH PVT LTD Page 11 of 30

 Force-X Force-Y Force-Z Moment- Moment- Moment- FOOTING tentative P/A+M/Zx+ P/A-M/Zx- EQ Col. Fdn
Node L/C SIZE P/A M/Zx M/Zy SBC CHECK Ratio
kN kN kN X kN-m Y kN-m Z kN-m Depth M/Zy M/Zy FACTOR No No
14 200 3.2 48.9 0 0 0 -0.9 1 1 0.2 50.3 0.0 -5.4 44.9 55.7 300 1 SAFE 0.19 C4 F1
201 3.5 52 4.4 3.8 0 -1 1 1 0.2 53.4 22.8 -6.0 70.2 36.6 300 1.25 SAFE 0.19 F1
202 3.5 52 -4.4 -3.8 0 -1 1 1 0.2 53.4 -22.8 -6.0 24.6 82.2 300 1.25 SAFE 0.22 F1
203 3.5 52 1.8 3 0.1 -1 1 1 0.2 53.4 18.0 -6.0 65.4 41.4 300 1.25 SAFE 0.17 F1
204 3.5 52 -1.8 -3 -0.1 -1 1 1 0.2 53.4 -18.0 -6.0 29.4 77.4 300 1.25 SAFE 0.21 F1
205 3.2 48.9 4.4 3.8 0 -0.9 1 1 0.2 50.3 22.8 -5.4 67.7 32.9 300 1.25 SAFE 0.18 F1
206 3.2 48.9 -4.4 -3.8 0 -0.9 1 1 0.2 50.3 -22.8 -5.4 22.1 78.5 300 1.25 SAFE 0.21 F1
207 3.2 48.9 1.8 3 0.1 -0.9 1 1 0.2 50.3 18.0 -5.4 62.9 37.7 300 1.25 SAFE 0.17 F1
208 3.2 48.9 -1.8 -3 -0.1 -0.9 1 1 0.2 50.3 -18.0 -5.4 26.9 73.7 300 1.25 SAFE 0.20 F1
15 200 -8.6 26.4 0 0 0 0.1 1 1 0.2 27.8 0.0 0.6 28.4 27.2 300 1 SAFE 0.09 C5 F1
201 -9.2 27.8 2.5 2.6 0.1 0.1 1 1 0.2 29.2 15.6 0.6 45.4 13.0 300 1.25 SAFE 0.12 F1
202 -9.2 27.8 -2.5 -2.6 -0.1 0.1 1 1 0.2 29.2 -15.6 0.6 14.2 44.2 300 1.25 SAFE 0.12 F1
203 -9.2 27.8 1 2 0.1 0.1 1 1 0.2 29.2 12.0 0.6 41.8 16.6 300 1.25 SAFE 0.11 F1
204 -9.2 27.8 -1 -2 -0.1 0.1 1 1 0.2 29.2 -12.0 0.6 17.8 40.6 300 1.25 SAFE 0.11 F1
205 -8.6 26.4 2.5 2.6 0.1 0.1 1 1 0.2 27.8 15.6 0.6 44.0 11.6 300 1.25 SAFE 0.12 F1
206 -8.6 26.4 -2.5 -2.6 -0.1 0.1 1 1 0.2 27.8 -15.6 0.6 12.8 42.8 300 1.25 SAFE 0.11 F1
207 -8.6 26.4 1 2 0.1 0.1 1 1 0.2 27.8 12.0 0.6 40.4 15.2 300 1.25 SAFE 0.11 F1
208 -8.6 26.4 -1 -2 -0.1 0.1 1 1 0.2 27.8 -12.0 0.6 16.4 39.2 300 1.25 SAFE 0.10 F1

SANGUINE INFRA TECH PVT LTD Page 12 of 30

 2.3.3.2 FOOTING DESIGN X DIR 1000 (footing size) (bar 2)
A' B' Y
FOOTING NO. F1

COLUMN NOS. C1 to C5 d/2

CONCRETE GRADE 30 N/mm2

STEEL GRADE 500 N/mm2 ( " a "dim)
a-dim b-dim Y DIR X 350 X
STAAD X -Direction Z -Direction 1000
COLUMN SIZE (mm) 250 350 Considered dia as Equivalent area (footing size) d eff.
column proj. 0 0 FOR SHUTTERING IN TRAPEZOIDAL (bar 1) projection(y)
250 350 FOOTING ONLY Factor Value load case 0.325 250 ( " b "dim)
Unfactored Maximum Upward Pressure = 82.2 Kn/m2 1.25 201
A' B'
along X dir. , B = 1000 mm 0.375
along Y dir = 1000 mm projection(x)

Proj. check for Ld A' B'

X -Direction Y -Direction X -Direction Y -Direction
FOOTING SIZE (mm) 1000 1000 325 275

Net upward pressure (Limit) = 102.75 Kn/m2 (deff)

0.14

(1) CHECK FOR BENDING MOMENT A' B'

Y
PARAMETERS ABOUT Y-Y ABOUT X-X UNITS projection(x) 0.375
Bending moment = 7.2 5.4 Kn-m SECTION ALONG X - X
Effective depth of footing required 41.7 36.2
Depth of footing provided 200 NOTE :- THE EXRECISE SHOWN BELOW IS TO BE PERFORMED IN RECTANGULAR FOOTINGS,
Cover to reinforcement = 50 ONLY & ONLY FOR SATISFYING ONE WAY SHEAR CRITERION, IF REQUIRED.
Effective Depth = 140
Depth of footing at extrem edge 200 IN RECTANGULAR FOOTING
PEDASTAL PROJECTION 0 0 mm NO. OF BARS TO BE PROVIDE TO SATISFY ONE WAY SHEAR CRITERIA
2
Ast (Required)= 120 90 mm BAR NO 2 BAR NO 1
Diameter of bar = 10 10 mm AST (Provided) 392.5 392.5 mm2 Min P%
Number of bars to be provided = 2 2 NO.S BAR 5 5 240 ok
Spacing of bars = 900 900 mm SP 250 250 mm

(2) CHECK FOR ONE WAY SHEAR

PARAMETERS ABOUT Y-Y ABOUT X-X UNITS

V= 24.15 19.01 Kn
b= 1000 1000 mm
Depth of footing at extrem edge = 200 200 mm
d= 140.00 140.00 mm
M = 2.84 1.76 Kn-m
Vnet = 24.15 19.01 Kn
Tv = 0.172 0.136 N/mm2
Pt (Provided)= 0.280 0.280 %
Beta = 12.42 12.42
Tc = 0.388 0.388

NO CORRECTION NO CORRECTION
REQUIRED REQUIRED

(3) CHECK FOR TWO WAY SHEAR

Critical section peri = 1760

d1 = 145.00
d2 = 145.00
d= 145.00
V= 83.11
Tv = 0.33
Beta = 0.71
Ks = 1
Tc = 1.37
NO CORRECTION
REQUIRED

SANGUINE INFRA TECH PVT LTD

Page 13 of 30
 2.3.3.3 SUMMARY

STAAD Node Nos and Grouping of Footing

F5

F4

F3

F2
F1

Isolated Footing
COLUMN
FOOTING SIZE FDN Rebar along Rebar along
FDN Col. No SIZE
Lx Ly DEPTH length (Lx) width (Ly)
x y

F1 C1 to C5 250 350 1000 1000 200 T10@250c/c T10@250c/c

SANGUINE INFRA TECH PVT LTD Page 14 of 30

2.3.4 - Reinforcement and ties of the Column are calculated based on the staad output.

Col. Size of the Ast Minimum Ast Column

Rebars-1 Rebars-2 Check
Nos Column Required % of Steel Provided Type

Building No 1

C1 250 x 350 91 644 4 Nos 12 Dia 2 Nos 12 Dia 678.6 Type 1 OK

C2 250 x 350 47 644 4 Nos 12 Dia 2 Nos 12 Dia 678.6 Type 1 OK
C3 250 x 350 46 644 4 Nos 12 Dia 2 Nos 12 Dia 678.6 Type 1 OK
C4 250 x 350 47 644 4 Nos 12 Dia 2 Nos 12 Dia 678.6 Type 1 OK
C5 250 x 350 91 644 4 Nos 12 Dia 2 Nos 12 Dia 678.6 Type 1 OK
Note:- Provide ties at T8@100c/c in the confinement zone and T8@100c/c in the regular zone as shown in the
drawing.

Page 15 of 30
SANGUINE INFRA TECH PVT LTD.
2.3.5 DESIGN OF GROUND BEAM
Drawing Beam No. GB1
STAAD Beam No. 2
Location @ 3.0 m Loc 0.23 m Loc 1.50 m Loc 3.00 m
Width mm 230 230 230
Depth mm 300 300 300
Fck Mpa 30 30 30
Fy Mpa 500 500 500
Clear cover mm 30 30 30
Effective coverd'to Ast mm 44 44 44
Effective depth 'd' mm 256 256 256
Mbal. kN-m 60 60 60
Moment Mu kN-m 12 8 17
Percentage redistribution % 0.0 0.0
Net Moment after redistibution (kN-m) 12.0 8.0 17.0
Shear force Vu kN 30 2 32
Torsion Tu kN-m 0 0 0
Ve kN 30 2 32
Me kN-m 12 8 17
b1 mm 102 102 102
d1 mm 192 192 192
2
Asv/Sv for torsion mm /mm 0.17 0.01 0.18
Remark O.K. O.K. O.K.
2
mm 111 73 160
Beam type to identify for ductile detail Frame Beam Frame beam Frame beam
Minimum Pt (0.85/fy or 0.24√fck/fy) % 0.263 0.263 0.263
Pt required % 0.26 0.26 0.27
Ast req for flexure bending= mm 2 155 155 160
Provide Dia. of reinf. mm Y12 Y12 Y12
Nos. 2 Nos. 2 Nos. 2 Nos.
+ Dia. of reinf. Y0 Y0 Y0
Nos. 0 Nos. 0 Nos. 0 Nos.
2
Giving Ast mm 226 226 226
2
mm Safe Safe Safe
Pt provided % 0.38 0.38 0.38
Shear stress Mpa 0.51 0.03 0.54
Beta 9.07 9.07 9.07
Permissible shear stress Mpa 0.44 0.44 0.44
Remark SR Req. Provide Min SR SR Req.
2
Asv/Sv req = mm /mm 0.04 -0.26 0.06
2
Asv/Sv min = mm /mm 0.25 0.25 0.25
Provide 2 Legged 2 Legged 2 Legged
Outer Strps Dia. of reinf. mm Y8 Y8 Y8
@ @ @ @
stirrups spacing mm 250c/c 250c/c 250c/c
0.40 0.40 0.40
Safe Safe Safe

Page 16 of 30
Drawing Beam No. GB2
STAAD Beam No. 4
Location @ 3.0 m Loc 0.23 m Loc 1.50 m Loc 2.78 m
Width mm 230 230 230
Depth mm 300 300 300
Fck Mpa 30 30 30
Fy Mpa 500 500 500
Clear cover mm 30 30 30
Effective coverd'to Ast mm 44 44 44
Effective depth 'd' mm 256 256 256
Mbal. kN-m 60 60 60
Moment Mu kN-m 17 8 15
Percentage redistribution % 0.0 0.0
Net Moment after redistibution (kN-m) 17.0 8.0 15.0
Shear force Vu kN 32 2 32
Torsion Tu kN-m 0 1 1
Ve kN 32 9 39
Me kN-m 17 9 16
b1 mm 102 102 102
d1 mm 192 192 192
2
Asv/Sv for torsion mm /mm 0.18 0.15 0.33
Remark O.K. O.K. O.K.
2
mm 160 86 154
Beam type to identify for ductile detail Frame Beam Frame beam Frame beam
Minimum Pt (0.85/fy or 0.24√fck/fy) % 0.263 0.263 0.263
Pt required % 0.27 0.26 0.26
Ast req for flexure bending= mm 2 160 155 155
Provide Dia. of reinf. mm Y12 Y12 Y12
Nos. 2 Nos. 2 Nos. 2 Nos.
+ Dia. of reinf. Y0 Y0 Y0
Nos. 0 Nos. 0 Nos. 0 Nos.
2
Giving Ast mm 226 226 226
2
mm Safe Safe Safe
Pt provided % 0.38 0.38 0.38
Shear stress Mpa 0.54 0.15 0.66
Beta 9.07 9.07 9.07
Permissible shear stress Mpa 0.44 0.44 0.44
Remark SR Req. Provide Min SR SR Req.
2
Asv/Sv req = mm /mm 0.06 -0.19 0.14
2
Asv/Sv min = mm /mm 0.25 0.25 0.25
Provide 2 Legged 2 Legged 2 Legged
Outer Strps Dia. of reinf. mm Y8 Y8 Y8
@ @ @ @
stirrups spacing mm 250c/c 250c/c 250c/c
0.40 0.40 0.40
Safe Safe Safe

Page 17 of 30
Drawing Beam No. GB3
STAAD Beam No. 6
Location @ 3.0 m Loc 0.23 m Loc 1.50 m Loc 2.78 m
Width mm 230 230 230
Depth mm 300 300 300
Fck Mpa 30 30 30
Fy Mpa 500 500 500
Clear cover mm 30 30 30
Effective coverd'to Ast mm 44 44 44
Effective depth 'd' mm 256 256 256
Mbal. kN-m 60 60 60
Moment Mu kN-m 15 8 17
Percentage redistribution % 0.0 0.0
Net Moment after redistibution (kN-m) 15.0 8.0 17.0
Shear force Vu kN 30 2 30
Torsion Tu kN-m 0 0 1
Ve kN 30 2 37
Me kN-m 15 8 18
b1 mm 102 102 102
d1 mm 192 192 192
2
Asv/Sv for torsion mm /mm 0.17 0.01 0.31
Remark O.K. O.K. O.K.
2
mm 140 73 173
Beam type to identify for ductile detail Frame Beam Frame beam Frame beam
Minimum Pt (0.85/fy or 0.24√fck/fy) % 0.263 0.263 0.263
Pt required % 0.26 0.26 0.29
Ast req for flexure bending= mm 2 155 155 173
Provide Dia. of reinf. mm Y12 Y12 Y12
Nos. 2 Nos. 2 Nos. 2 Nos.
+ Dia. of reinf. Y0 Y0 Y0
Nos. 0 Nos. 0 Nos. 0 Nos.
2
Giving Ast mm 226 226 226
2
mm Safe Safe Safe
Pt provided % 0.38 0.38 0.38
Shear stress Mpa 0.51 0.03 0.63
Beta 9.07 9.07 9.07
Permissible shear stress Mpa 0.44 0.44 0.44
Remark SR Req. Provide Min SR SR Req.
2
Asv/Sv req = mm /mm 0.04 -0.26 0.12
2
Asv/Sv min = mm /mm 0.25 0.25 0.25
Provide 2 Legged 2 Legged 2 Legged
Outer Strps Dia. of reinf. mm Y8 Y8 Y8
@ @ @ @
stirrups spacing mm 250c/c 250c/c 250c/c
0.40 0.40 0.40
Safe Safe Safe

Page 18 of 30
Drawing Beam No. GB4
STAAD Beam No. 8
Location @ 3.0 m Loc 0.23 m Loc 1.50 m Loc 2.78 m
Width mm 230 230 230
Depth mm 300 300 300
Fck Mpa 30 30 30
Fy Mpa 500 500 500
Clear cover mm 30 30 30
Effective coverd'to Ast mm 44 44 44
Effective depth 'd' mm 256 256 256
Mbal. kN-m 60 60 60
Moment Mu kN-m 17 9 12
Percentage redistribution % 0.0 0.0
Net Moment after redistibution (kN-m) 17.0 9.0 12.0
Shear force Vu kN 30 2 30
Torsion Tu kN-m 0 0 1
Ve kN 30 2 37
Me kN-m 17 9 13
b1 mm 102 102 102
d1 mm 192 192 192
2
Asv/Sv for torsion mm /mm 0.17 0.01 0.31
Remark O.K. O.K. O.K.
2
mm 160 83 124
Beam type to identify for ductile detail Frame Beam Frame beam Frame beam
Minimum Pt (0.85/fy or 0.24√fck/fy) % 0.263 0.263 0.263
Pt required % 0.27 0.26 0.26
Ast req for flexure bending= mm 2 160 155 155
Provide Dia. of reinf. mm Y12 Y12 Y12
Nos. 2 Nos. 2 Nos. 2 Nos.
+ Dia. of reinf. Y0 Y0 Y0
Nos. 0 Nos. 0 Nos. 0 Nos.
2
Giving Ast mm 226 226 226
2
mm Safe Safe Safe
Pt provided % 0.38 0.38 0.38
Shear stress Mpa 0.51 0.03 0.63
Beta 9.07 9.07 9.07
Permissible shear stress Mpa 0.44 0.44 0.44
Remark SR Req. Provide Min SR SR Req.
2
Asv/Sv req = mm /mm 0.04 -0.26 0.12
2
Asv/Sv min = mm /mm 0.25 0.25 0.25
Provide 2 Legged 2 Legged 2 Legged
Outer Strps Dia. of reinf. mm Y8 Y8 Y8
@ @ @ @
stirrups spacing mm 250c/c 250c/c 250c/c
0.40 0.40 0.40
Safe Safe Safe

Page 19 of 30
2.3.6 DESIGN OF COPING BEAM
Drawing Beam No. CB1
STAAD Beam No. 3
Location @ 3.0 m Loc 0.23 m Loc 1.50 m Loc 3.00 m
Width mm 280 280 280
Depth mm 125 125 125
Fck Mpa 30 30 30
Fy Mpa 500 500 500
Clear cover mm 30 30 30
Effective coverd'to Ast mm 43 43 43
Effective depth 'd' mm 82 82 82
Mbal. kN-m 8 8 8
Moment Mu kN-m 1 1 1
Percentage redistribution % 0.0 0.0
Net Moment after redistibution (kN-m) 1.0 1.0 1.0
Shear force Vu kN 2 1 2
Torsion Tu kN-m 0 0 0
Ve kN 2 1 2
Me kN-m 1 1 1
b1 mm 154 154 154
d1 mm 19 19 19
2
Asv/Sv for torsion mm /mm 0.12 0.06 0.12
Remark O.K. O.K. O.K.
2
mm 29 29 29
Beam type to identify for ductile detail Frame Beam Frame beam Frame beam
Minimum Pt (0.85/fy or 0.24√fck/fy) % 0.263 0.263 0.263
Pt required % 0.26 0.26 0.26
Ast req for flexure bending= mm 2 60 60 60
Provide Dia. of reinf. mm Y10 Y10 Y10
Nos. 2 Nos. 2 Nos. 2 Nos.
+ Dia. of reinf. Y0 Y0 Y0
Nos. 0 Nos. 0 Nos. 0 Nos.
2
Giving Ast mm 157 157 157
2
mm Safe Safe Safe
Pt provided % 0.68 0.68 0.68
Shear stress Mpa 0.09 0.04 0.09
Beta 5.09 5.09 5.09
Permissible shear stress Mpa 0.56 0.56 0.56
Remark Provide Min SR Provide Min SR Provide Min SR
2
Asv/Sv req = mm /mm -0.37 -0.40 -0.37
2
Asv/Sv min = mm /mm 0.31 0.31 0.31
Provide 2 Legged 2 Legged 2 Legged
Outer Strps Dia. of reinf. mm Y8 Y8 Y8
@ @ @ @
stirrups spacing mm 250c/c 250c/c 250c/c
0.40 0.40 0.40
Safe Safe Safe

Page 20 of 30
Drawing Beam No. CB2
STAAD Beam No. 5
Location @ 3.0 m Loc 0.23 m Loc 1.50 m Loc 2.78 m
Width mm 280 280 280
Depth mm 125 125 125
Fck Mpa 30 30 30
Fy Mpa 500 500 500
Clear cover mm 30 30 30
Effective coverd'to Ast mm 43 43 43
Effective depth 'd' mm 82 82 82
Mbal. kN-m 8 8 8
Moment Mu kN-m 1 1 1
Percentage redistribution % 0.0 0.0
Net Moment after redistibution (kN-m) 1.0 1.0 1.0
Shear force Vu kN 2 1 2
Torsion Tu kN-m 0 0 0
Ve kN 2 1 2
Me kN-m 1 1 1
b1 mm 154 154 154
d1 mm 19 19 19
2
Asv/Sv for torsion mm /mm 0.12 0.06 0.12
Remark O.K. O.K. O.K.
2
mm 29 29 29
Beam type to identify for ductile detail Frame Beam Frame beam Frame beam
Minimum Pt (0.85/fy or 0.24√fck/fy) % 0.263 0.263 0.263
Pt required % 0.26 0.26 0.26
Ast req for flexure bending= mm 2 60 60 60
Provide Dia. of reinf. mm Y10 Y10 Y10
Nos. 2 Nos. 2 Nos. 2 Nos.
+ Dia. of reinf. Y0 Y0 Y0
Nos. 0 Nos. 0 Nos. 0 Nos.
2
Giving Ast mm 157 157 157
2
mm Safe Safe Safe
Pt provided % 0.68 0.68 0.68
Shear stress Mpa 0.09 0.04 0.09
Beta 5.09 5.09 5.09
Permissible shear stress Mpa 0.56 0.56 0.56
Remark Provide Min SR Provide Min SR Provide Min SR
2
Asv/Sv req = mm /mm -0.37 -0.40 -0.37
2
Asv/Sv min = mm /mm 0.31 0.31 0.31
Provide 2 Legged 2 Legged 2 Legged
Outer Strps Dia. of reinf. mm Y8 Y8 Y8
@ @ @ @
stirrups spacing mm 250c/c 250c/c 250c/c
0.40 0.40 0.40
Safe Safe Safe

Page 21 of 30
Drawing Beam No. CB3
STAAD Beam No. 7
Location @ 3.0 m Loc 0.23 m Loc 1.50 m Loc 2.78 m
Width mm 280 280 280
Depth mm 125 125 125
Fck Mpa 30 30 30
Fy Mpa 500 500 500
Clear cover mm 30 30 30
Effective coverd'to Ast mm 43 43 43
Effective depth 'd' mm 82 82 82
Mbal. kN-m 8 8 8
Moment Mu kN-m 1 1 1
Percentage redistribution % 0.0 0.0
Net Moment after redistibution (kN-m) 1.0 1.0 1.0
Shear force Vu kN 2 1 2
Torsion Tu kN-m 0 0 0
Ve kN 2 1 2
Me kN-m 1 1 1
b1 mm 154 154 154
d1 mm 19 19 19
2
Asv/Sv for torsion mm /mm 0.12 0.06 0.12
Remark O.K. O.K. O.K.
2
mm 29 29 29
Beam type to identify for ductile detail Frame Beam Frame beam Frame beam
Minimum Pt (0.85/fy or 0.24√fck/fy) % 0.263 0.263 0.263
Pt required % 0.26 0.26 0.26
Ast req for flexure bending= mm 2 60 60 60
Provide Dia. of reinf. mm Y10 Y10 Y10
Nos. 2 Nos. 2 Nos. 2 Nos.
+ Dia. of reinf. Y0 Y0 Y0
Nos. 0 Nos. 0 Nos. 0 Nos.
2
Giving Ast mm 157 157 157
2
mm Safe Safe Safe
Pt provided % 0.68 0.68 0.68
Shear stress Mpa 0.09 0.04 0.09
Beta 5.09 5.09 5.09
Permissible shear stress Mpa 0.56 0.56 0.56
Remark Provide Min SR Provide Min SR Provide Min SR
2
Asv/Sv req = mm /mm -0.37 -0.40 -0.37
2
Asv/Sv min = mm /mm 0.31 0.31 0.31
Provide 2 Legged 2 Legged 2 Legged
Outer Strps Dia. of reinf. mm Y8 Y8 Y8
@ @ @ @
stirrups spacing mm 250c/c 250c/c 250c/c
0.40 0.40 0.40
Safe Safe Safe

Page 22 of 30
Drawing Beam No. CB4
STAAD Beam No. 9
Location @ 3.0 m Loc 0.23 m Loc 1.50 m Loc 2.78 m
Width mm 280 280 280
Depth mm 125 125 125
Fck Mpa 30 30 30
Fy Mpa 500 500 500
Clear cover mm 30 30 30
Effective coverd'to Ast mm 43 43 43
Effective depth 'd' mm 82 82 82
Mbal. kN-m 8 8 8
Moment Mu kN-m 1 1 1
Percentage redistribution % 0.0 0.0
Net Moment after redistibution (kN-m) 1.0 1.0 1.0
Shear force Vu kN 2 1 2
Torsion Tu kN-m 0 0 0
Ve kN 2 1 2
Me kN-m 1 1 1
b1 mm 154 154 154
d1 mm 19 19 19
2
Asv/Sv for torsion mm /mm 0.12 0.06 0.12
Remark O.K. O.K. O.K.
2
mm 29 29 29
Beam type to identify for ductile detail Frame Beam Frame beam Frame beam
Minimum Pt (0.85/fy or 0.24√fck/fy) % 0.263 0.263 0.263
Pt required % 0.26 0.26 0.26
Ast req for flexure bending= mm 2 60 60 60
Provide Dia. of reinf. mm Y10 Y10 Y10
Nos. 2 Nos. 2 Nos. 2 Nos.
+ Dia. of reinf. Y0 Y0 Y0
Nos. 0 Nos. 0 Nos. 0 Nos.
2
Giving Ast mm 157 157 157
2
mm Safe Safe Safe
Pt provided % 0.68 0.68 0.68
Shear stress Mpa 0.09 0.04 0.09
Beta 5.09 5.09 5.09
Permissible shear stress Mpa 0.56 0.56 0.56
Remark Provide Min SR Provide Min SR Provide Min SR
2
Asv/Sv req = mm /mm -0.37 -0.40 -0.37
2
Asv/Sv min = mm /mm 0.31 0.31 0.31
Provide 2 Legged 2 Legged 2 Legged
Outer Strps Dia. of reinf. mm Y8 Y8 Y8
@ @ @ @
stirrups spacing mm 250c/c 250c/c 250c/c
0.40 0.40 0.40
Safe Safe Safe

Page 23 of 30
3.0 REFERENCES

3.1 IS-456:2000 Standard specification and code of practice for Plain &
Reinforced Concrete structures.
3.2 IS-1893:2002 Criteria for Earthquake Resistance Design of Structure
Part 1: General provision and Buildings
3.3 IS-1893 (Part 1): 2002 - Criteria for earthquake resistant design of structures
3.4 IS- 875 (Part 1)-1987 Code of practice for design loads (Other than Earthquake)
Dead Loads - Unit weights of building Materials and Stored Materials (Second Revision)
3.5 IS- 875 (Part 2) 1987- Code of practice for design loads (other than Earthquake)
buildings and structures . Part 2 Imposed Loads
3.6 IS- 875 (Part 3) 2015 -Code of practice for design loads (Other than earthquake)
for (Reaffirmed 2003) building and structures . Part -3 Wind Loads
3.7 SP- 16 – 1980 Design aids for reinforced concrete
3.8 SP- 34 – 1987 Handbook on concrete reinforcement detailing
3.9 Reinforced concrete – Limit State design – Ashok K. Jain

4.0 LIST OF DRAWINGS

4.1 KRCPL-SIT-PTDP-CW-DD-100 Overall plan of compound wall

4.2 KRCPL-SIT-PTDP-CW-DD-101 Overall plan of compound wall
4.3 KRCPL-SIT-PTDP-CW-DD-102 Elevation of compound wall
4.4 KRCPL-SIT-PTDP-CW-DD-103 Sections & details of compound wall

Page 24 of 30
i. Annexure A - DESIGN OUTPUT OF RCC COLUMN

=========================================================
IS 456 - 2000 C O L U M N D E S I G N R E S U L T S
=========================================================
IS-456 L I M I T STATE DESIGN
C O L U M N N O. 1 DESIGN RESULTS

M30 Fe500 (Main) Fe415 (Sec.)

LENGTH: 2400.0 mm CROSS SECTION: 350.0 mm X 250.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 105 END JOINT: 1 SHORT COLUMN

REQD. STEEL AREA : 69.05 Sq.mm.

REQD. CONCRETE AREA: 8631.87 Sq.mm.
MAIN REINFORCEMENT : Provide 4 - 12 dia. (0.52%, 452.39 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1206.21 Muz1 : 4.90 Muy1 : 6.86

INTERACTION RATIO: 0.93 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 105
END JOINT: 1 Puz : 1344.79 Muz : 20.68 Muy : 30.02 IR: 0.22
=========================================================

=========================================================
IS-456 L I M I T STATE DESIGN
C O L U M N N O. 10 D E S I G N R E S U L T S

M30 Fe500 (Main) Fe415 (Sec.)

LENGTH: 2400.0 mm CROSS SECTION: 350.0 mm X 250.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 100 END JOINT: 3 SHORT COLUMN

REQD. STEEL AREA : 8.75 Sq.mm.

REQD. CONCRETE AREA: 1093.75 Sq.mm.
MAIN REINFORCEMENT : Provide 4 - 12 dia. (0.52%, 452.39 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1184.41 Muz1 : 2.01 Muy1 : 2.81

INTERACTION RATIO: 0.21 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 105
END JOINT: 3 Puz : 1344.79 Muz : 20.84 Muy : 30.27 IR: 0.07
=========================================================

=========================================================

Page 25 of 30
 IS-456 L I M I T STATE DESIGN
C O L U M N N O. 11 D E S I G N R E S U L T S

M30 Fe500 (Main) Fe415 (Sec.)

LENGTH: 2400.0 mm CROSS SECTION: 350.0 mm X 250.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 107 END JOINT: 5 SHORT COLUMN

REQD. STEEL AREA : 22.72 Sq.mm.

REQD. CONCRETE AREA: 2839.38 Sq.mm.
MAIN REINFORCEMENT : Provide 4 - 12 dia. (0.52%, 452.39 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1189.46 Muz1 : 2.14 Muy1 : 3.00

INTERACTION RATIO: 0.71 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 105
END JOINT: 5 Puz : 1344.79 Muz : 20.84 Muy : 30.28 IR: 0.08
=========================================================

=========================================================
IS-456 L I M I T STATE DESIGN
C O L U M N N O. 12 D E S I G N R E S U L T S

M30 Fe500 (Main) Fe415 (Sec.)

LENGTH: 2400.0 mm CROSS SECTION: 350.0 mm X 250.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 100 END JOINT: 7 SHORT COLUMN

REQD. STEEL AREA : 8.75 Sq.mm.

REQD. CONCRETE AREA: 1093.75 Sq.mm.
MAIN REINFORCEMENT : Provide 4 - 12 dia. (0.52%, 452.39 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1184.41 Muz1 : 2.01 Muy1 : 2.81

INTERACTION RATIO: 0.21 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 105
END JOINT: 7 Puz : 1344.79 Muz : 20.84 Muy : 30.27 IR: 0.07

=========================================================

=========================================================
IS-456 L I M I T STATE DESIGN
C O L U M N N O. 13 D E S I G N R E S U L T S

M30 Fe500 (Main) Fe415 (Sec.)

LENGTH: 2400.0 mm CROSS SECTION: 350.0 mm X 250.0 mm COVER: 40.0 mm

Page 26 of 30
 ** GUIDING LOAD CASE: 105 END JOINT: 9 SHORT COLUMN

REQD. STEEL AREA : 69.05 Sq.mm.

REQD. CONCRETE AREA: 8631.87 Sq.mm.
MAIN REINFORCEMENT : Provide 4 - 12 dia. (0.52%, 452.39 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1206.21 Muz1 : 4.90 Muy1 : 6.86

INTERACTION RATIO: 0.93 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 105
END JOINT: 9 Puz : 1344.79 Muz : 20.68 Muy : 30.02 IR: 0.22
=========================================================

=========================================================
IS-456 L I M I T STATE DESIGN
C O L U M N N O. 14 D E S I G N R E S U L T S

M30 Fe500 (Main) Fe415 (Sec.)

LENGTH: 600.0 mm CROSS SECTION: 350.0 mm X 250.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 105 END JOINT: 1 SHORT COLUMN

REQD. STEEL AREA : 90.89 Sq.mm.

REQD. CONCRETE AREA: 11360.94 Sq.mm.
MAIN REINFORCEMENT : Provide 4 - 12 dia. (0.52%, 452.39 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1214.11 Muz1 : 8.99 Muy1 : 12.53

INTERACTION RATIO: 0.98 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 105
END JOINT: 1 Puz : 1344.79 Muz : 22.99 Muy : 33.61 IR: 0.38
=========================================================

=========================================================
IS-456 L I M I T STATE DESIGN
C O L U M N N O. 15 D E S I G N R E S U L T S

M30 Fe500 (Main) Fe415 (Sec.)

LENGTH: 600.0 mm CROSS SECTION: 350.0 mm X 250.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 100 END JOINT: 12 SHORT COLUMN

REQD. STEEL AREA : 46.63 Sq.mm.

REQD. CONCRETE AREA: 5828.79 Sq.mm.
MAIN REINFORCEMENT : Provide 4 - 12 dia. (0.52%, 452.39 Sq.mm.)

Page 27 of 30
 (Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1198.11 Muz1 : 11.21 Muy1 : 15.66

INTERACTION RATIO: 0.24 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 105
END JOINT: 12 Puz : 1344.79 Muz : 26.00 Muy : 38.27 IR: 0.20

=========================================================

=========================================================
IS-456 L I M I T STATE DESIGN
C O L U M N N O. 16 D E S I G N R E S U L T S

M30 Fe500 (Main) Fe415 (Sec.)

LENGTH: 600.0 mm CROSS SECTION: 350.0 mm X 250.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 100 END JOINT: 13 SHORT COLUMN

REQD. STEEL AREA : 45.59 Sq.mm.

REQD. CONCRETE AREA: 5699.33 Sq.mm.
MAIN REINFORCEMENT : Provide 4 - 12 dia. (0.52%, 452.39 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1197.73 Muz1 : 10.98 Muy1 : 15.34

INTERACTION RATIO: 0.24 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 105
END JOINT: 13 Puz : 1344.79 Muz : 25.86 Muy : 38.06 IR: 0.21
=========================================================

=========================================================
IS-456 L I M I T STATE DESIGN
C O L U M N N O. 17 D E S I G N R E S U L T S

M30 Fe500 (Main) Fe415 (Sec.)

LENGTH: 600.0 mm CROSS SECTION: 350.0 mm X 250.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 100 END JOINT: 14 SHORT COLUMN

REQD. STEEL AREA : 46.63 Sq.mm.

REQD. CONCRETE AREA: 5828.79 Sq.mm.
MAIN REINFORCEMENT : Provide 4 - 12 dia. (0.52%, 452.39 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1198.11 Muz1 : 11.21 Muy1 : 15.66

Page 28 of 30
 INTERACTION RATIO: 0.24 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 105
END JOINT: 14 Puz : 1344.79 Muz : 26.00 Muy : 38.27 IR: 0.20
=========================================================

=========================================================
IS-456 L I M I T STATE DESIGN
C O L U M N N O. 18 D E S I G N R E S U L T S

M30 Fe500 (Main) Fe415 (Sec.)

LENGTH: 600.0 mm CROSS SECTION: 350.0 mm X 250.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 105 END JOINT: 9 SHORT COLUMN

REQD. STEEL AREA : 90.89 Sq.mm.

REQD. CONCRETE AREA: 11360.94 Sq.mm.
MAIN REINFORCEMENT : Provide 4 - 12 dia. (0.52%, 452.39 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1214.11 Muz1 : 8.99 Muy1 : 12.53

INTERACTION RATIO: 0.98 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 105
END JOINT: 9 Puz : 1344.79 Muz : 22.99 Muy : 33.61 IR: 0.38

=========================================================

********************END OF COLUMN DESIGN RESULTS********************

Page 29 of 30
ii. Annexure B - BMD & SFD of Beams

BENDING MOMENT DIAGRAM (ENVELOPE)

SHEAR FORCE DIAGRAM (ENVELOPE)

Page 30 of 30