Scribd
Upload
30 views2 pages

New Text Document

This document lists error codes for Toshiba E-Studio copiers and printers. It includes codes for paper jams in various parts of the devices like the duplex unit, feeder, and finisher. It also lists codes for problems with motors, sensors, boards, memory, communication errors, and hard drive issues. Clearing instructions are provided for some errors like fuser errors.

Uploaded by

chellam cervai balu
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
30 views2 pages

New Text Document

This document lists error codes for Toshiba E-Studio copiers and printers. It includes codes for paper jams in various parts of the devices like the duplex unit, feeder, and finisher. It also lists codes for problems with motors, sensors, boards, memory, communication errors, and hard drive issues. Clearing instructions are provided for some errors like fuser errors.

Uploaded by

chellam cervai balu
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 2

E520: Duplex entry jam.

E550: Transport jam.


E711-E743: RADF jams.
E860, E870: RADF open cover.
E910-E940: Finisher/bridge jam.
E950, E951: Job separator jam.
E960, E961: Offset tray jam.
E9F0: Finisher/punch jam.EA10,
EA20, EA30, EA40, EA50, EA60, EA70: Finisher jams.
EA80, EA90, EAA0, EAB0 EAC0, EAD0, EAE0, EAF0: Saddle-stitch finisher jams.EB30:
Finisher jam.EB50, EB60: Transport jams.F070: Communication error between system-
CPPU and engine-CPU.F090: SYS board SRAM.F091: NVRAM problem on SYS board.F092:
SRAM and NVRAM problem on SYS board.F100: Hard drive format error.F101: Hard drive
connection.F102: Hard drive start
TOSHIBA E-STUDIO E-350 / 352 / 450 / 452, DP-3520 / DP-4520TROUBLE CODESThese might
not display automatically. If the machine has a jam (\"Clear paper\") or \"picture
of awrench\" you can read these codes. To read them, press down the \"8\" key and
the “Clear/Stop”
key at the same time. All codes, except fuser errors, are reset by turning the
machine off andback on again.C010: Drive system.C040: PFP motor.C130: Upper drawer
motor.C140: Lower drawer motor.C150: PFP upper drawer motor.C160: PFP lower drawer
motor.C180: LCF tray motor.C1A0: LCF end fence motor.C1B0: LCF transport
motor.C260: Exposure lamp not detected.C270: Scan home problem.C280: Scan home
problem.C410: Fuser low temp or thermistor.C440: Fuser too high or too low.C450:
Fuser thermistor.C470: IH initialization power voltage. No AC
C480: IGBT overheat.C490: IH control problem.
To clear fuser errors; turn on power while holding down “0” & “8.” Enter 400. Press
“Start.”Change status to “0.” Press
\"ENTER\" or \"INTERRUPT.\" Shut power and turn back on.C550: Communication
problem between IF and RADF.C570: Communication problem between engine-CPU and
IPC.C580: Communication problem between IPC and finisher.C730: EEPROM
initialization problem in RADF.C810: Fan problem.C820: Read sensor adjustment
error.C830: Original length sensor adjustment error.C940: Engine-CPU problem.C970:
HVT or charge corona.CA10: Laser motor (polygon motor) problem.CA20: Laser H-SYNC
problem.CB20: Finisher exit motor.Cb30: Finisher tray1/tray2 shift motor.Cb30:
Finisher tray1/tray 2 shift motor.CB40: Finisher alignment plate motor.CB50: Staple
motor.
CB60: Staple shift motor problem.CB80: Finisher backup RAM problem.CB90: Finisher
paper push plate motor CB7: Finisher height sensor.CBA0: Saddle stitcher front
stitcher motor.CBB0: Saddle stitcher rear stitcher motor.CBC0: Saddle stitcher
alignment motor.CBD0: Saddle stitcher guide motor.CBE0: Saddle stitcher folding
motor.CBF0: Saddle stitcher paper positioning plate motor.CC00: Finisher sensor
connector error.CC10: Finisher micro switch.CC20: Saddle stitcher to finisher
communications problem.CC30: Stack process motor.CC40: Finisher swing motor.
CC50: Finisher horizontal registration motor.CC60: Finisher punch motor.CC80:
Finisher front alignment motor.CC90: Finisher upper stack tray lift motor.CCA0:
Finisher lower stack tray lift motor.CCB0: Finisher rear jogger motor.CCDO:
Finisher stack eject motor.CCE0: Finisher paper trail edge assist motor.CCF0:
Finisher gear change motor.CDF0: Offset tray home separator problem.CE00:
Communication problem between finisher and punch.E010: Exit jam.E020: Exit
jam.E030: Jam.E090: Jam
E110: Duplex jam.E120: By pass jam.E130: Upper drawer jam.E140: Lower drawer
jam.E150: PFP upper drawer jam.E160: PFP lower drawer jam.E190: LCF jam.E200: Upper
drawer transport jam.E210: Lower drawer transport jam.E220: Lower drawer transport
jam.E300, 310, 320: PFP upper drawer transport jam.E330, 340, 350, 360: PFP lower
drawer transport jam.E3C0, E3D0, E3E0: LCF transport jam.E400: Jam access cover
open.E410: Front cover open.E420: PFP side cover open.E430: Duplex unit open.E440:
Side cover open.E450: LCF side cover open.E480: Bridge open.E490: Job separator
cover open.E491: Offset tray cover open.E510: Duplex exit jam
E520: Duplex entry jam.E550: Transport jam.E711-E743: RADF jams.E860, E870: RADF
open cover.E910-E940: Finisher/bridge jam.E950, E951: Job separator jam.E960, E961:
Offset tray jam.E9F0: Finisher/punch jam.EA10, EA20, EA30, EA40, EA50, EA60, EA70:
Finisher jams.EA80, EA90, EAA0, EAB0 EAC0, EAD0, EAE0, EAF0: Saddle-stitch finisher
jams.EB30: Finisher jam.EB50, EB60: Transport jams.F070: Communication error
between system-CPPU and engine-CPU.F090: SYS board SRAM.F091: NVRAM problem on SYS
board.F092: SRAM and NVRAM problem on SYS board.F100: Hard drive format error.F101:
Hard drive connection.F102: Hard drive start
F103: Hard drive time out.F104: Hard drive data error.F105: Hard drive.F106: Point
and print partition problem.F107: SHR partition.F108: SHA partition.F110:
Communication error between system-CPU and scan-CPU.F111: Scan problem.F120:
Database problem

You might also like