FCC PART 15 B

TEST REPORT
For

Quanzhou Wouxun Electronics Co., Ltd.

Jiangnan High Technology Industry Park, No.928 Nanhuan Road, Quanzhou, Fujian, China

FCC ID: WVTWOUXUN12

Report Type: Pro duct Na me:

Orig inal Repor t Two-Wa y Rad io

Test Engineer: Kevin Hu

Report Number: RXM170418050A

Report Date: 2017-06-29

Henry Ding
EMC Leader
Reviewed By:

Test Laboratory: Bay Area Compliance Laboratories Corp. (Chengdu)

5040, HuiLongWan Plaza, No. 1, ShaWan Road,
JinNiu District, ChengDu, China
Tel: 028-65523123, Fax: 028-65525125
www.baclcorp.com

Note: This test report was prepared for the customer shown above and for the device described herein. It may not be
duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. (Chengdu).
Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and
offenders may be prosecuted to the fullest extent of the law. This report was valid only with a valid digital
signature.
 Bay Area Compliance Laboratories Corp. (Chengdu)

TABLE OF CONTENTS

GENERAL INFORMATION ........................................................................................................................................3

PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT)................................................................................3
OBJECTIVE ..................................................................................................................................................................3
RELATED SUBMITTAL(S)/GRANT(S) ............................................................................................................................3
TEST METHODOLOGY .................................................................................................................................................4
TEST FACILITY .............................................................................................................................................................4
SYSTEM TEST CONFIGURATION ...........................................................................................................................5
DESCRIPTION OF TEST CONFIGURATION ...................................................................................................................5
EUT EXERCISE SOFTWARE ........................................................................................................................................5
EQUIPMENT MODIFICATIONS ......................................................................................................................................5
LOCAL SUPPORT EQUIPMENT LIST AND DETAILS ......................................................................................................5
SUPPORT CABLE LIST AND DETAILS...........................................................................................................................5
CONFIGURATION OF TEST SETUP...............................................................................................................................6
SUMMARY OF TEST RESULTS ...............................................................................................................................7
FCC§15.107 - CONDUCTED EMISSIONS ..............................................................................................................8
EUT SETUP .................................................................................................................................................................8
EMI TEST RECEIVER SETUP ......................................................................................................................................8
TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................9
TEST PROCEDURE ......................................................................................................................................................9
CORRECTED AMPLITUDE & MARGIN CALCULATION ...................................................................................................9
TEST DATA ................................................................................................................................................................10
FCC §15.109 - RADIATED SPURIOUS EMISSIONS ..........................................................................................13
EUT SETUP ...............................................................................................................................................................13
EMI TEST RECEIVER SETUP ....................................................................................................................................14
TEST PROCEDURE ....................................................................................................................................................14
TEST EQUIPMENT LIST AND DETAILS .......................................................................................................................14
CORRECTED AMPLITUDE & MARGIN CALCULATION .................................................................................................15
TEST DATA ................................................................................................................................................................15
FCC §15.121 – COMPLIANCE FOR SCANNING RECEIVER ...........................................................................18
APPLICABLE STANDARD ............................................................................................................................................18
EUT SETUP ...............................................................................................................................................................18
TEST PROCEDURE ....................................................................................................................................................18
TEST EQUIPMENT LIST AND DETAILS .......................................................................................................................19
TEST RESULTS SUMMARY ........................................................................................................................................19
TEST DATA ................................................................................................................................................................20

Report No.: RXM170418050A Page 2 of 20

 Bay Area Compliance Laboratories Corp. (Chengdu)

GENERAL INFORMATION

Product Description for Equipment Under Test (EUT)

The Quanzhou Wouxun Electronics Co., Ltd.’s product, model number: KG-UV9D (FCC ID:
WVTWOUXUN12) (the "EUT") in this report was a Two-Way Radio, which was measured
approximately: 6.15 cm (L) x 3.39 cm (W) x 12.5 cm (H), rated input voltage: DC7.4V from Li-ion
battery or DC 12V from adapter.

Adapter Information:
Model: CA-001
Input:AC 100-240V 50/60Hz 0.3A
Output:DC12V 500Ma

Note: The series product, models KG-UV9D, KG-UV8D, KG-UV8D(Plus), KG-UV7D, KG-UV9D(Plus),
KG-UV83, KG-UV86, KG-UV66, KG-UV899, KG-UV8A, KG-UV8E, KG-UV8F, KG-UV8G, KG-UV8H,
KG-UV8T are electrically identical, we selected KG-UV9D for fully testing, and the details of the differences
between them were explained in the attached declaration letter.

*All measurement and test data in this report was gathered from final production sample, serial number:
170418050 (assigned by the BACL, Chengdu). It may have deviation from any other sample. The EUT
supplied by the applicant was received on 2017-04-18, and EUT conformed to test requirement.

Objective

This test report is prepared on behalf of Quanzhou Wouxun Electronics Co., Ltd. in accordance
with Part 2, Subpart J, and Part 15-Subparts A and B of the Federal Communications
Commission’s rules.

The objective of the manufacturer is to determine the compliance of EUT with FCC Part 15 B Class
B.

Related Submittal(s)/Grant(s)

NO Related Submittal(s)/Grant(s)

Report No.: RXM170418050A Page 3 of 20

Bay Area Compliance Laboratories Corp. (Chengdu)

Test Methodology

All measurements contained in this report were conducted with ANSI C63.4-2014, American
National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage
Electrical and Electronic Equipment in the range of 9 kHz to 40 GHz.

The Bay Area Compliance Laboratories Corp. Chengdu’s measurement Uncertainties (calculated
for a k=2 Coverage Factor corresponding to approximately 95% Coverage) were as follows:

-For all of the AC Line Conducted Emissions Tests reported herein: ±3.17 dB.

-For of all of the direct Radiated Emissions Tests reported herein are:
30 MHz to 200 MHz: ±4.7 dB;
200 MHz to 1 GHz: ±6.0 dB;
1 GHz to 6 GHz: ±5.13dB; and,
6 GHz to 40 GHz: ±5.47dB.

And the uncertainty will not be taken into consideration for all test data recorded in the report.

Test Facility

The test site used by BACL to collect test data is located in the 5040, HuiLongWan Plaza, No. 1,
ShaWan Road, JinNiu District, ChengDu, China.

Test site at BACL has been fully described in reports submitted to the Federal Communication
Commission (FCC). The details of these reports have been found to be in compliance with the
requirements of Section 2.948 of the FCC Rules on April 24, 2015. The facility also complies with
the radiated and AC line conducted test site criteria set forth in ANSI C63.4-2014.

The Federal Communications Commission has the reports on file and is listed under FCC
Registration No.: 910975. The test site has been approved by the FCC for public use and is listed
in the FCC Public Access Link (PAL) database.

Report No.: RXM170418050A Page 4 of 20

Bay Area Compliance Laboratories Corp. (Chengdu)

SYSTEM TEST CONFIGURATION

Description of Test Configuration

The system was configured for testing in a typical fashion (as normally used by a typical user).

EUT Exercise Software

No software was used during test.

Equipment Modifications

No modification was made to the EUT tested.

Local Support Equipment List and Details

Manufacturer Description Model Serial Number

HP Signal Generator 1026 320408

Support Cable List and Details

Cable Shielding Length

Ferrite Core From Port To
Description Type (m)
Power line No No 1.5 LISN EUT

Report No.: RXM170418050A Page 5 of 20

Bay Area Compliance Laboratories Corp. (Chengdu)

Configuration of Test Setup

Report No.: RXM170418050A Page 6 of 20

Bay Area Compliance Laboratories Corp. (Chengdu)

SUMMARY OF TEST RESULTS

FCC Rules Description of Test Results

§15.107 Conducted Emissions Compliance

§15.109 Radiated Emissions Compliance

§15.121 Compliance for Scanning Receiver Compliance

Report No.: RXM170418050A Page 7 of 20

Bay Area Compliance Laboratories Corp. (Chengdu)

FCC§15.107 - CONDUCTED EMISSIONS

EUT Setup

The setup of EUT is according with per ANSI C63.4-2014 measurement procedure. The
specification used was with the FCC Part 15 B Class B limits.

The external I/O cables were draped along the test table and formed a bundle 30 to 40 cm long in
the middle.

The Adapter was connected to the main LISN with a 120V/60Hz AC power source.

EMI Test Receiver Setup

The EMI test receiver was set to investigate the spectrum from 150 kHz to 30 MHz.

During the conducted emission test, the EMI test receiver was set with the following configurations:

Frequency Range IF B/W

150 kHz – 30 MHz 9 kHz

Report No.: RXM170418050A Page 8 of 20

Bay Area Compliance Laboratories Corp. (Chengdu)

Test Equipment List and Details

Serial Calibration Calibration

Manufacturer Description Model
Number Date Due Date
EMI Test
Rohde & Schwarz ESCS 30 836858/0016 2016-12-02 2017-12-01
Receiver
Rohde & Schwarz L.I.S.N. ENV216 100018 2016-12-02 2017-12-01
SOLAR 9252-50-24
L.I.S.N. 984413 2016-12-02 2017-12-01
ELECTRONICS -BNC
Rohde & Schwarz PULSE LIMITER ESH3Z2 DE14781 2016-10-31 2017-10-30
Unknown Conducted Cable Unknown NO.5 2016-11-10 2017-11-09
R&S Test Software EMC32 Version8.53.0 N/A N/A

* Statement of Traceability: BACL(Chengdu) attests that all of the calibrations on the equipment items
listed above were traceable to NIM or to another internationally recognized National Metrology Institute
(NMI), and were compliant with the NIST HB 150-2016 Normative Annex B “Implementation of traceability
policy in accredited laboratories”.

Test Procedure

During the conducted emission test, the Adapter was connected to the outlet of the first LISN and
the other support equipments were connected to the outlet of the second LISN.

Maximizing procedure was performed on the six (6) highest emissions of the EUT.

All data was recorded in the Quasi-peak and average detection mode.

Corrected Amplitude & Margin Calculation

The basic equation is as follows:

VC = VR + AC + VDF

Herein,
VC: corrected voltage amplitude

VR: reading voltage amplitude

Ac: attenuation caused by cable loss

VDF: voltage division factor of AMN or ISN

Report No.: RXM170418050A Page 9 of 20

Bay Area Compliance Laboratories Corp. (Chengdu)

The “Margin” column of the following data tables indicates the degree of compliance within the
applicable limit. For example, a margin of 7dB means the emission is 7dB below the maximum
limit. The equation for margin calculation is as follows:

Margin = Limit – Corrected Amplitude

Test Data

Environmental Conditions

Temperature: 26.2 C
Relative Humidity: 56 %
ATM Pressure: 99.7 kPa

The testing was performed by Kevin Hu on 2017-06-17.

Report No.: RXM170418050A Page 10 of 20

Bay Area Compliance Laboratories Corp. (Chengdu)

Test Mode: Downloading

AC120V, 60Hz, Line:

80

70
Quasi-Peak Limit
60
Average Limit
50
Level in dBμ

40

30

20

10

0
150k 300 400 500 800 1M 2M 3M 4M 5M 6 8 10M 20M 30M
Frequency in Hz

Frequency QuasiPeak Bandwidth Corr. Margin Limit

Line Comment
(MHz) (dBμV) (kHz) (dB) (dB) (dBμV)
0.161152 59.1 9.000 L1 19.7 6.3 65.4 Compliance
0.192030 53.4 9.000 L1 19.7 10.5 63.9 Compliance
0.223418 47.9 9.000 L1 19.7 14.8 62.7 Compliance
0.524077 38.5 9.000 L1 19.7 17.5 56.0 Compliance
0.639600 46.3 9.000 L1 19.7 9.7 56.0 Compliance
4.261034 40.3 9.000 L1 19.7 15.7 56.0 Compliance

Frequency Average Bandwidth Corr. Margin Limit

Line Comment
(MHz) (dBμV) (kHz) (dB) (dB) (dBμV)
0.162441 51.1 9.000 L1 19.7 4.2 55.3 Compliance
0.193566 43.0 9.000 L1 19.7 10.9 53.9 Compliance
0.511698 33.4 9.000 L1 19.7 12.6 46.0 Compliance
0.545378 33.8 9.000 L1 19.7 12.2 46.0 Compliance
0.639600 39.6 9.000 L1 19.7 6.4 46.0 Compliance
4.227217 34.2 9.000 L1 19.7 11.8 46.0 Compliance

Report No.: RXM170418050A Page 11 of 20

Bay Area Compliance Laboratories Corp. (Chengdu)

AC120V, 60Hz, Neutral:

80

70
Quasi-Peak Limit
60

Average Limit
50
Level in dBμ

40

30

20

10

0
150k 300 400 500 800 1M 2M 3M 4M 5M 6 8 10M 20M 30M
Frequency in Hz

Frequency QuasiPeak Bandwidth Corr. Margin Limit

Line Comment
(MHz) (dBμV) (kHz) (dB) (dB) (dBμV)
0.161152 61.7 9.000 N 19.7 3.7 65.4 Compliance
0.193566 55.7 9.000 N 19.6 8.2 63.9 Compliance
0.225205 50.2 9.000 N 19.6 12.4 62.6 Compliance
0.262017 43.5 9.000 N 19.6 17.9 61.4 Compliance
3.547503 37.7 9.000 N 19.7 18.3 56.0 Compliance
4.127365 39.3 9.000 N 19.7 16.7 56.0 Compliance

Frequency Average Bandwidth Corr. Margin Limit

Line Comment
(MHz) (dBμV) (kHz) (dB) (dB) (dBμV)
0.163741 51.6 9.000 N 19.7 3.7 55.3 Compliance
0.193566 45.2 9.000 N 19.6 8.7 53.9 Compliance
0.227007 39.3 9.000 N 19.6 13.3 52.6 Compliance
0.515791 32.6 9.000 N 19.6 13.4 46.0 Compliance
0.644717 31.0 9.000 N 19.6 15.0 46.0 Compliance
4.261034 32.7 9.000 N 19.7 13.3 46.0 Compliance

Report No.: RXM170418050A Page 12 of 20

Bay Area Compliance Laboratories Corp. (Chengdu)

FCC §15.109 - RADIATED SPURIOUS EMISSIONS

EUT Setup

Below 1GHz:

Above 1GHz:

The radiated emission tests were performed at the 3 meters distance in chamber, using the setup
accordance with the ANSI C63.4-2014. The specification used was the FCC Part 15.109 Class B
limits.

Report No.: RXM170418050A Page 13 of 20

Bay Area Compliance Laboratories Corp. (Chengdu)

EMI Test Receiver Setup

The system was investigated from 30 MHz to 6.0 GHz.

During the radiated emission test, the EMI test receiver was set with the following configurations:

Frequency Range RBW Video B/W IF B/W Detector

30 MHz – 1000 MHz 120 kHz 300 kHz 120 kHz QP
1 MHz 3 MHz / Peak
Above 1 GHz
1 MHz 10 Hz / AVG

Test Procedure

During the radiated emissions, the Adapter was connected to the first AC floor outlet and the other
support equipments were connected to the second AC floor outlet.

Maximizing procedure was performed on the highest emissions to ensure that the EUT complied
with all installation combinations.

The data was recorded in the Quasi-peak detection mode for below 1 GHz, peak and average
detection mode above 1 GHz.

Test Equipment List and Details

Serial Calibration Calibration

Manufacturer Description Model
Number Date Due Date
Agilent Amplifier 8447D 2944A10442 2016-12-02 2017-12-01
Rohde &
EMI Test Receiver ESCI 100028 2016-12-02 2017-12-01
Schwarz
Sunol Sciences Broadband Antenna JB3 A121808 2016-04-10 2019-04-09
Rohde &
Spectrum Analyzer FSEM30 100018 2016-12-02 2017-12-01
Schwarz
ETS Horn Antenna 3115 003-6076 2016-12-02 2017-12-01
Mini-circuits Amplifier ZVA-183-S+ 771001215 2017-05-20 2018-05-19
Semi-Anechoic
EMCT 966 966-1 2015-04-24 2018-04-23
Chamber
RF Cable
Unknown Unknown NO.1 2016-11-10 2017-11-09
(below 1GHz)
RF Cable
Unknown Unknown NO.4 2016-11-10 2017-11-09
(below 1GHz)
RF Cable
Unknown Unknown NO.2 2016-11-10 2017-11-09
(above 1GHz)
* Statement of Traceability: BACL(Chengdu) attests that all of the calibrations on the equipment items
listed above were traceable to NIM or to another internationally recognized National Metrology Institute
(NMI), and were compliant with the NIST HB 150-2016 Normative Annex B “Implementation of traceability
policy in accredited laboratories”.

Report No.: RXM170418050A Page 14 of 20

Bay Area Compliance Laboratories Corp. (Chengdu)

Corrected Amplitude & Margin Calculation

The Corrected Amplitude is calculated by adding the Antenna Loss and Cable Loss, and
subtracting the Amplifier Gain from the Meter Reading. The basic equation is as follows:

Corrected Amplitude = Meter Reading + Antenna Factor + Cable Loss - Amplifier Gain

The “Margin” column of the following data tables indicates the degree of compliance with the
applicable limit. For example, a margin of 7 dB means the emission is 7 dB below the limit. The
equation for margin calculation
is as follows:

Margin = Limit – Corrected Amplitude

Test Data

Environmental Conditions

Temperature: 26 C
Relative Humidity: 38 %
ATM Pressure: 102kPa

* The testing was performed by Kevin Hu on 2017-06-16.

Test Result: Compliance

Test Mode: Receiver

Report No.: RXM170418050A Page 15 of 20

 Bay Area Compliance Laboratories Corp. (Chengdu)

30MHz-5GHz:

SG Frequency: 145MHz
Receiver Rx Antenna Cable Amplifier Corrected
Frequency Limit Margin
Reading Polar Factor loss Gain Amplitude
(MHz) Detector (dBμV/m) (dB)
(dBμV) (H/V) (dB(1/m)) (dB) (dB) (dBμV/m)
77.53 51.33 QP H 7.88 0.45 28.41 31.25 40.00 8.75
113.42 39.94 QP H 13.97 0.56 28.21 26.26 43.50 17.24
175.5 48.15 QP H 11.43 0.93 27.95 32.56 43.50 10.94
238.55 42.74 QP H 12.24 1.08 27.55 28.51 46.00 17.49
332.64 28.34 QP H 14.73 1.17 27.68 16.56 46.00 29.44
361.74 32.08 QP H 15.70 1.49 27.93 21.34 46.00 24.66
38.73 48.59 QP V 16.30 0.38 28.52 36.75 40.00 3.25
76.56 55.72 QP V 7.83 0.46 28.41 35.60 40.00 4.40
130.88 42.12 QP V 14.66 0.71 28.15 29.34 43.50 14.16
173.56 49.49 QP V 11.52 0.92 27.96 33.97 43.50 9.53
237.58 40.6 QP V 12.20 1.09 27.56 26.33 46.00 19.67
336.52 27.15 QP V 14.77 1.15 27.70 15.37 46.00 30.63
1245 45.68 PK H 23.44 2.32 26.57 44.87 74.00 29.13
1245 35.1 AV H 23.44 2.32 26.57 34.29 54.00 19.71
1130.261 51.39 PK V 23.14 2.16 26.68 50.01 74.00 23.99
1130.261 40.6 AV V 23.14 2.16 26.68 39.22 54.00 14.78
1350.701 52.57 PK V 23.71 2.46 26.47 52.27 74.00 21.73
1350.701 41.66 AV V 23.71 2.46 26.47 41.36 54.00 12.64
2452.906 50.98 PK V 23.36 3.00 26.88 50.46 74.00 23.54
2452.906 40.18 AV V 23.36 3.00 26.88 39.66 54.00 14.34

Report No.: RXM170418050A Page 16 of 20

 Bay Area Compliance Laboratories Corp. (Chengdu)

SG Frequency: 435 MHz

Receiver Rx Antenna Cable Amplifier Corrected
Frequency Limit Margin
Reading Polar Factor loss Gain Amplitude
(MHz) Detector (dBμV/m) (dB)
(dBμV) (H/V) (dB(1/m)) (dB) (dB) (dBμV/m)
77.53 52.36 QP H 7.88 0.45 28.41 32.28 40.00 7.72
113.42 40.21 QP H 13.97 0.56 28.21 26.53 43.50 16.97
175.5 46.26 QP H 11.43 0.93 27.95 30.67 43.50 12.83
238.55 44.36 QP H 12.24 1.08 27.55 30.13 46.00 15.87
332.64 34.26 QP H 14.73 1.17 27.68 22.48 46.00 23.52
361.74 33.69 QP H 15.70 1.49 27.93 22.95 46.00 23.05
38.73 47.84 QP V 16.30 0.38 28.52 36.00 40.00 4.00
76.56 55.64 QP V 7.83 0.46 28.41 35.52 40.00 4.48
130.88 43.21 QP V 14.66 0.71 28.15 30.43 43.50 13.07
173.56 48.74 QP V 11.52 0.92 27.96 33.22 43.50 10.28
237.58 42.65 QP V 12.20 1.09 27.56 28.38 46.00 17.62
1350.701 53.69 PK V 23.71 2.46 26.47 53.39 74.00 20.61
1350.701 42.36 AV V 23.71 2.46 26.47 42.06 54.00 11.94
2452.906 51.44 PK V 23.36 3.00 26.88 50.92 74.00 23.08
2452.906 42.69 AV V 23.36 3.00 26.88 42.17 54.00 11.83

Report No.: RXM170418050A Page 17 of 20

Bay Area Compliance Laboratories Corp. (Chengdu)

FCC §15.121 – COMPLIANCE FOR SCANNING RECEIVER

Applicable Standard
FCC §15.121

EUT Setup

For FCC §15.121 (b) Scanning Receiver Cellular Band Rejection Test

RF Signal Grenrator EUT Distortion Meter

Power Supply

Test Procedure

1) Connected the EUT as shown in the above block diagram.

2) Apply a RF signal to the receiver input port at lowest, middle and highest channel frequencies of
receiver operation band.

3) Adjust the audio output level of the receiver to it’s rated value with the distortion less than 10%.

4) Adjust the RF Signal Generator Output Power to produce 12 dB SINAD without the audio output
power dropping by more than 3 dB.This output level of the RF SG at each channel frequency is the
sensitivity of the receiver.

5) Select the lowest or worse-case sensitivity level for all of the bands as the reference sensitivity.

6) Adjust the RF Signal Generator output to a level of +60 dB above the reference sensitivity
obtained in step 5) and its frequency to the frequency points in the cellular band.

7) Set the Receiver squelch to threshold, the signal required to open the squelch must be lower
than the reference sensitivity level.

8) Set the receiver in a scanning mode and allow it to scan through it’s complete receiving range.

9) If the receiver unsquelched or stopped on any frequency, receiving at this frequency, then adjust
the signal generator output level until 12 dB SINAD is produced, this level is the spurious value and
the difference between the reference sensitivity and the spurious value is the rejection ratio and
must be at least 38dB.

10) Repeat above procedure at the frequencies 824.5, 836.0, and 848.5 MHz for the mobile band,
and 869.1, 881.5, and 893.5MHz for the cellular base band.

Report No.: RXM170418050A Page 18 of 20

Bay Area Compliance Laboratories Corp. (Chengdu)

Test Equipment List and Details

Serial Calibration Calibration

Manufacturer Description Model
Number Date Due Date
RF Communications
HP 8920A 00 247 2016-08-10 2017-08-09
Test Set
HEWLETT Signal Generator ESG-D3000A N/A 2016-12-02 2017-12-01
FLUKE Multimeter 1587 27870099 2016-12-30 2017-12-29

* Statement of Traceability: BACL (Chengdu) attested that all calibrations have been performed, traceable
to National Primary Standards and International System of Units (SI).

Test Results Summary

Comply with FCC 121(a):

– Please refer to the technical informations or the attestation letter conforming compliance with this
requirement.

Comply with FCC 121(b):

– Please refer to the following Scanning Receiver Cellular Band Rejection Test Result.

Comply with FCC 121(c):

– Not applicable.

Comply with FCC 121(d):

–Please refer to the User Manual.

Comply with FCC 121(e):

– This Scanning Receiver is not assembled from kits or marketed in kit form.

Comply with FCC 121(f):

–Please refer to the label of the product.

Report No.: RXM170418050A Page 19 of 20

Bay Area Compliance Laboratories Corp. (Chengdu)

Test Data

For FCC §15.121(b) Scanning Receiver Cellular Band Rejection

Environmental Conditions

Temperature: 26 C
Relative Humidity: 38 %
ATM Pressure: 102kPa

* The testing was performed by Kevin Hu on 2017-06-16.

Test Result: Compliance

Scanning Receiver Cellular Band Rejection Test Data:

EUT’s
Test Spurious Value of Reference
Scanning Rejection Rejection
Frequencies of Cellular Frequencies Sensitivity for
Frequency Ratio Ratio Limit
Cellular Band for 12 dB SINAD 12 dB SINAD
Band (dB) (dB)
(MHz) (dBm) (dBm)
(MHz)
824.5, 836.0,
144-148 848.5,
> -51.2 -116.5 < -65.3 < -38.0
420-450 869.1, 881.5,
893.5

Note: Rejection Ratio = Reference Sensitivity - Spurious Value

Result

Compliance with the requirements specified in Part 15.121 for scanning receiver.

***** END OF REPORT *****

Report No.: RXM170418050A Page 20 of 20